GS8160ZV18AGT-150T [GSI]
ZBT SRAM, 1MX18, 7.5ns, CMOS, PQFP100, TQFP-100;型号: | GS8160ZV18AGT-150T |
厂家: | GSI TECHNOLOGY |
描述: | ZBT SRAM, 1MX18, 7.5ns, CMOS, PQFP100, TQFP-100 静态存储器 |
文件: | 总23页 (文件大小:489K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
100-Pin TQFP
Commercial Temp
Industrial Temp
350 MHz–150 MHz
18Mb Pipelined and Flow Through
1.8 V VDD
1.8 V I/O
Synchronous NBT SRAM
read/ write control inputs are captured on the rising edge of the
input clock. Burst order control (LBO) must be tied to a power
rail for proper operation. Asynchronous inputs include the
Sleep mode enable (ZZ) and Output Enable. Output Enable can
be used to override the synchronous control of the output
drivers and turn the RAM's output drivers off at any time.
Write cycles are internally self-timed and initiated by the rising
edge of the clock input. This feature eliminates complex off-
chip write pulse generation required by asynchronous SRAMs
and simplifies input signal timing.
Features
• NBT (No Bus Turn Around) functionality allows zero wait
read-write-read bus utilization; Fully pin-compatible with
both pipelined and flow through NtRAM™, NoBL™ and
ZBT™ SRAMs
• 1.8 V +10%/–10% core power supply
• 1.8 V I/O supply
• User-configurable Pipeline and Flow Through mode
• LBO pin for Linear or Interleave Burst mode
• Pin compatible with 2M, 4M, and 8M devices
• Byte write operation (9-bit Bytes)
The GS8160ZV18/36AT may be configured by the user to
operate in Pipeline or Flow Through mode. Operating as a
pipelined synchronous device, meaning that in addition to the
rising edge triggered registers that capture input signals, the
device incorporates a rising-edge-triggered output register. For
read cycles, pipelined SRAM output data is temporarily stored
by the edge triggered output register during the access cycle
and then released to the output drivers at the next rising edge of
clock.
• 3 chip enable signals for easy depth expansion
• ZZ Pin for automatic power-down
• JEDEC-standard 100-lead TQFP package
Functional Description
The GS8160ZV18/36AT is an 18Mbit Synchronous Static
SRAM. GSI's NBT SRAMs, like ZBT, NtRAM, NoBL or
other pipelined read/double late write or flow through read/
single late write SRAMs, allow utilization of all available bus
bandwidth by eliminating the need to insert deselect cycles
when the device is switched from read to write cycles.
The GS8160ZV18/36AT is implemented with GSI's high
performance CMOS technology and is available in a JEDEC-
standard 100-pin TQFP package.
Because it is a synchronous device, address, data inputs, and
Parameter Synopsis
-350 -333 -300 -250 -200 -150 Unit
tKQ
tCycle
1.8
2.85
2.0
3.0
2.2
3.3
2.3
4.0
2.7
5.0
3.3
6.7
ns
ns
Pipeline
3-1-1-1
395
455
370
430
335
390
280
330
230
270
185
210
mA
mA
Curr (x18)
Curr (x36)
tKQ
4.5
4.5
4.7
4.7
5.0
5.0
5.5
5.5
6.5
6.5
7.5
7.5
ns
ns
Flow
Through
2-1-1-1
tCycle
270
305
250
285
230
270
210
240
185
205
170
190
mA
mA
Curr (x18)
Curr (x36)
Rev: 1.00a 6/2003
1/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
NoBL is a trademark of Cypress Semiconductor Corp.. NtRAM is a trademark of Samsung Electronics Co.. ZBT is a trademark of Integrated Device Technology, Inc.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
GS8160ZV18AT Pinout
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
A
NC
1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
NC
V
NC
NC
2
3
V
4
DDQ
DDQ
SS
V
NC
V
5
SS
NC
NC
6
DQPA
DQA
DQA
7
8
DQB
DQB
V
9
1M x 18
Top View
V
V
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
SS
DDQ
SS
V
DDQ
DQA
DQB
DQA
DQB
FT
V
SS
NC
V
V
DD
DD
SS
V
DD
ZZ
V
DQA
DQA
DQB
DQB
V
V
V
DDQ
DDQ
SS
V
SS
DQA
DQA
NC
DQB
DQB
DQPB
NC
NC
V
V
SS
DDQ
SS
V
V
DDQ
NC
NC
NC
NC
NC
NC
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.00a 6/2003
2/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
GS8160ZV36AT Pinout
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
DQPB
DQB
DQPC
1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQC
DQC
2
DQB
3
V
V
V
4
DDQ
DDQ
SS
V
5
SS
DQB
DQB
DQB
DQB
DQC
DQC
DQC
DQC
6
7
8
9
512K x 36
Top View
V
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
SS
DDQ
SS
V
V
DDQ
DQB
DQC
DQB
DQC
FT
V
SS
NC
V
V
V
DD
DD
SS
V
DD
ZZ
DQA
DQA
DQD
DQD2
V
V
V
DDQ
DDQ
SS
V
SS
DQA
DQA
DQA
DQA
DQD
DQD
DQD
DQD
V
V
DDQ
DQD
DQD
DQPD
SS
DDQ
SS
V
V
DQA
DQA
DQPA
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.00a 6/2003
3/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
100-Pin TQFP Pin Descriptions
Symbol
A0, A1
A
Type
In
Description
Burst Address Inputs; Preload the burst counter
In
Address Inputs
Clock Input Signal
CK
In
BA
In
Byte Write signal for data inputs DQA1-DQA9; active low
Byte Write signal for data inputs DQB1-DQB9; active low
Byte Write signal for data inputs DQC1-DQC9; active low
Byte Write signal for data inputs DQD1-DQD9; active low
Write Enable; active low
BB
In
BC
In
BD
In
W
In
E1
In
Chip Enable; active low
E2
In
Chip Enable; Active High. For self decoded depth expansion
Chip Enable; Active Low. For self decoded depth expansion
Output Enable; active low
E3
In
G
In
ADV
CKE
NC
DQA
DQB
DQC
DQD
ZZ
In
Advance/Load; Burst address counter control pin
Clock Input Buffer Enable; active low
No Connect
In
—
I/O
I/O
I/O
I/O
In
Byte A Data Input and Output pins
Byte B Data Input and Output pins
Byte C Data Input and Output pins
Byte D Data Input and Output pins
Power down control; active high
FT
In
Pipeline/Flow Through Mode Control; active low
Linear Burst Order; active low
LBO
In
V
In
Core power supply
DD
V
In
In
Ground
SS
V
Output driver power supply
DDQ
Rev: 1.00a 6/2003
4/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
GS8160ZV18/36A NBT SRAM Functional Block Diagram
n s e e S A m p s
i t r e W D r i v e r
s
Rev: 1.00a 6/2003
5/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Functional Details
Clocking
Deassertion of the Clock Enable (CKE) input blocks the Clock input from reaching the RAM's internal circuits. It may be used to
suspend RAM operations. Failure to observe Clock Enable set-up or hold requirements will result in erratic operation.
Pipeline Mode Read and Write Operations
All inputs (with the exception of Output Enable, Linear Burst Order and Sleep) are synchronized to rising clock edges. Single cycle
read and write operations must be initiated with the Advance/Load pin (ADV) held low, in order to load the new address. Device
activation is accomplished by asserting all three of the Chip Enable inputs (E1, E2 and E3). Deassertion of any one of the Enable
inputs will deactivate the device.
Function
Read
W
H
L
BA
X
BB
X
BC
X
BD
X
Write Byte “a”
Write Byte “b”
Write Byte “c”
Write Byte “d”
Write all Bytes
Write Abort/NOP
L
H
L
H
H
L
H
H
H
L
L
H
H
H
L
L
H
H
L
L
H
L
L
L
L
H
H
H
H
Read operation is initiated when the following conditions are satisfied at the rising edge of clock: CKE is asserted Low, all three
chip enables (E1, E2, and E3) are active, the write enable input signals W is deasserted high, and ADV is asserted low. The address
presented to the address inputs is latched in to address register and presented to the memory core and control logic. The control
logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At
the next rising edge of clock the read data is allowed to propagate through the output register and onto the output pins.
Write operation occurs when the RAM is selected, CKE is active, and the Write input is sampled low at the rising edge of clock.
The Byte Write Enable inputs (BA, BB, BC, & BD) determine which bytes will be written. All or none may be activated. A write
cycle with no Byte Write inputs active is a no-op cycle. The pipelined NBT SRAM provides double late write functionality,
matching the write command versus data pipeline length (2 cycles) to the read command versus data pipeline length (2 cycles). At
the first rising edge of clock, Enable, Write, Byte Write(s), and Address are registered. The Data In associated with that address is
required at the third rising edge of clock.
Flow Through Mode Read and Write Operations
Operation of the RAM in Flow Through mode is very similar to operations in Pipeline mode. Activation of a Read Cycle and the
use of the Burst Address Counter is identical. In Flow Through mode the device may begin driving out new data immediately after
new address are clocked into the RAM, rather than holding new data until the following (second) clock edge. Therefore, in Flow
Through mode the read pipeline is one cycle shorter than in Pipeline mode.
Write operations are initiated in the same way, but differ in that the write pipeline is one cycle shorter as well, preserving the ability
to turn the bus from reads to writes without inserting any dead cycles. While the pipelined NBT RAMs implement a double late
write protocol, in Flow Through mode a single late write protocol mode is observed. Therefore, in Flow Through mode, address
and control are registered on the first rising edge of clock and data in is required at the data input pins at the second rising edge of
clock.
Rev: 1.00a 6/2003
6/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Synchronous Truth Table
Operation
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Continue
Read Cycle, Begin Burst
Read Cycle, Continue Burst
NOP/Read, Begin Burst
Dummy Read, Continue Burst
Write Cycle, Begin Burst
Write Cycle, Continue Burst
NOP/Write Abort, Begin Burst
Write Abort, Continue Burst
Clock Edge Ignore, Stall
Sleep Mode
Type Address E1 E2 E3 ZZ ADV W Bx G CKE CK DQ Notes
D
D
D
D
R
B
None
None
H
X
X
X
L
X
X
L
X
H
X
X
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
X
X
X
X
H
X
H
X
L
X
X
X
X
X
X
X
X
L
X
X
X
X
L
L
L
L
L
L
L
L
L
L
L
L
L
H
X
L-H High-Z
L-H High-Z
L-H High-Z
L-H High-Z
None
L
None
X
H
X
H
X
H
X
H
X
X
X
H
L
1
External
Next
L-H
L-H
Q
Q
X
L
X
L
H
L
L
1,10
2
R
B
External
Next
H
H
X
X
X
X
X
X
L-H High-Z
X
L
X
L
H
L
L-H High-Z 1,2,10
W
B
External
Next
L-H
L-H
D
D
3
X
L
X
L
H
L
X
L
L
1,3,10
2,3
W
B
None
H
H
X
X
L-H High-Z
Next
X
X
X
X
X
X
H
X
X
X
X
X
L-H High-Z 1,2,3,10
Current
None
L-H
X
-
4
High-Z
Notes:
1. Continue Burst cycles, whether read or write, use the same control inputs. A Deselect continue cycle can only be entered into if a Dese-
lect cycle is executed first.
2. Dummy Read and Write abort can be considered NOPs because the SRAM performs no operation. A Write abort occurs when the W
pin is sampled low but no Byte Write pins are active so no write operation is performed.
3. G can be wired low to minimize the number of control signals provided to the SRAM. Output drivers will automatically turn off during
write cycles.
4. If CKE High occurs during a pipelined read cycle, the DQ bus will remain active (Low Z). If CKE High occurs during a write cycle, the bus
will remain in High Z.
5. X = Don’t Care; H = Logic High; L = Logic Low; Bx = High = All Byte Write signals are high; Bx = Low = One or more Byte/Write
signals are Low
6. All inputs, except G and ZZ must meet setup and hold times of rising clock edge.
7. Wait states can be inserted by setting CKE high.
8. This device contains circuitry that ensures all outputs are in High Z during power-up.
9. A 2-bit burst counter is incorporated.
10. The address counter is incriminated for all Burst continue cycles.
Rev: 1.00a 6/2003
7/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Pipeline and Flow Through Read Write Control State Diagram
D
B
Deselect
R
D
D
W
New Read
New Write
R
R
W
B
B
R
W
W
R
Burst Read
Burst Write
B
B
D
D
Key
Notes:
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
2. W, R, B and D represent input command
codes ,as indicated in the Synchronous Truth Table.
Current State (n)
Next State (n+1)
n
n+1
n+2
n+3
Clock (CK)
Command
ƒ
ƒ
ƒ
ƒ
Current State
Next State
Current State and Next State Definition for Pipeline and Flow Through Read/Write Control State Diagram
Rev: 1.00a 6/2003
8/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Pipeline Mode Data I/O State Diagram
Intermediate
Intermediate
R
B
W
B
Intermediate
R
Data Out
(Q Valid)
High Z
(Data In)
W
D
Intermediate
D
Intermediate
W
R
High Z
B
D
Intermediate
Key
Notes:
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
Transition
2. W, R, B, and D represent input command
codes as indicated in the Truth Tables.
Current State (n)
Next State (n+2)
Intermediate State (N+1)
n
n+1
n+2
n+3
Clock (CK)
Command
ƒ
ƒ
ƒ
ƒ
Intermediate
State
Current State
Next State
Current State and Next State Definition for Pipeline Mode Data I/O State Diagram
Rev: 1.00a 6/2003
9/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Flow Through Mode Data I/O State Diagram
R
B
W
B
R
Data Out
(Q Valid)
High Z
(Data In)
W
D
D
W
R
High Z
B
D
Key
Notes
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
2. W, R, B and D represent input command
codes as indicated in the Truth Tables.
Current State (n)
Next State (n+1)
n
n+1
n+2
n+3
Clock (CK)
Command
ƒ
ƒ
ƒ
ƒ
Current State
Next State
Current State and Next State Definition for: Pipeline and Flow Through Read Write Control State Diagram
Rev: 1.00a 6/2003
10/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Burst Cycles
Although NBT RAMs are designed to sustain 100% bus bandwidth by eliminating turnaround cycle when there is transition from
read to write, multiple back-to-back reads or writes may also be performed. NBT SRAMs provide an on-chip burst address
generator that can be utilized, if desired, to further simplify burst read or write implementations. The ADV control pin, when
driven high, commands the SRAM to advance the internal address counter and use the counter generated address to read or write
the SRAM. The starting address for the first cycle in a burst cycle series is loaded into the SRAM by driving the ADV pin low, into
Load mode.
Burst Order
The burst address counter wraps around to its initial state after four addresses (the loaded address and three more) have been
accessed. The burst sequence is determined by the state of the Linear Burst Order pin (LBO). When this pin is low, a linear burst
sequence is selected. When the RAM is installed with the LBO pin tied high, Interleaved burst sequence is selected. See the tables
below for details.
Mode Pin Functions
Pin
Mode Name
Burst Order Control
Output Register Control
Power Down Control
State
Function
Name
L
Linear Burst
Interleaved Burst
Flow Through
Pipeline
LBO
H
L
FT
ZZ
H or NC
L or NC
H
Active
Standby, I = I
DD SB
Note:
There are pull-up devices on the FT pin and a pull-down device on the ZZ pin, so those input pins can be unconnected and the chip
will operate in the default states as specified in the above tables.
Burst Counter Sequences
Linear Burst Sequence
Interleaved Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0]
A[1:0] A[1:0] A[1:0] A[1:0]
1st address
2nd address
3rd address
4th address
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
1st address
2nd address
3rd address
4th address
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Note: The burst counter wraps to initial state on the 5th clock.
Note: The burst counter wraps to initial state on the 5th clock.
BPR 1999.05.18
Rev: 1.00a 6/2003
11/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Sleep Mode
During normal operation, ZZ must be pulled low, either by the user or by it’s internal pull down resistor. When ZZ is pulled high,
the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to
low, the SRAM operates normally after ZZ recovery time.
Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to I 2. The duration of
SB
Sleep mode is dictated by the length of time the ZZ is in a high state. After entering Sleep mode, all inputs except ZZ become
disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode.
When the ZZ pin is driven high, I 2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending
SB
operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated
until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a deselect or read commands
may be applied while the SRAM is recovering from Sleep mode.
Sleep Mode Timing Diagram
CK
tZZR
ZZ
Sleep
tZZS
tZZH
Designing for Compatibility
The GSI NBT SRAMs offer users a configurable selection between Flow Through mode and Pipeline mode via the FT signal found
on Pin 14. Not all vendors offer this option, however most mark Pin 14 as V or V
on pipelined parts and V on flow
DD
DDQ
SS
through parts. GSI NBT SRAMs are fully compatible with these sockets.
Rev: 1.00a 6/2003
12/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Absolute Maximum Ratings
(All voltages reference to V
)
SS
Symbol
Description
Value
Unit
V
V
Voltage on V Pins
–0.5 to 3.6
DD
DD
V
Voltage in V
Pins
DDQ
–0.5 to 3.6
V
DDQ
V
–0.5 to V
+0.5 (≤ 3.6 V max.)
DDQ
Voltage on I/O Pins
Voltage on Other Input Pins
Input Current on Any Pin
Output Current on Any I/O Pin
Package Power Dissipation
Storage Temperature
V
I/O
V
–0.5 to V +0.5 (≤ 3.6 V max.)
V
IN
DD
I
+/–20
+/–20
mA
mA
W
IN
I
OUT
P
1.5
D
o
T
–55 to 125
–55 to 125
C
STG
o
T
Temperature Under Bias
C
BIAS
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of
this component.
Rev: 1.00a 6/2003
13/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Power Supply Voltage Ranges
Parameter
Symbol
Min.
1.6
Typ.
1.8
Max.
2.0
Unit
V
Notes
V
1.8 V Supply Voltage
DD1
1.8 V V
I/O Supply Voltage
V
1.6
1.8
2.0
V
DDQ
DDQ1
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are
evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 3.6 V maximum, with a pulse width not to exceed 20% tKC.
V
Range Logic Levels
Parameter
DDQ
Symbol
Min.
Typ.
—
Max.
Unit
Notes
V
Input High Voltage
V
0.6*V
V
+ 0.3
DD
V
V
V
V
1
DD
IH
DD
V
Input Low Voltage
V
0.3*V
DD
–0.3
—
1
DD
IL
V
I/O Input High Voltage
I/O Input Low Voltage
V
0.6*V
V
+ 0.3
DDQ
—
1,3
1,3
DDQ
IHQ
DD
V
V
0.3*V
DD
–0.3
—
DDQ
ILQ
Notes:
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are
evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 3.6 V maximum, with a pulse width not to exceed 20% tKC.
3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V.
Recommended Operating Temperatures
Parameter
Symbol
Min.
0
Typ.
25
Max.
70
Unit
°C
Notes
T
Ambient Temperature (Commercial Range Versions)
2
2
A
T
Ambient Temperature (Industrial Range Versions)
Note:
–40
25
85
°C
A
1. The part numbers of Industrial Temperature Range versions end the character “I”. Unless otherwise noted, all performance specifications quoted are
evaluated for worst case in the temperature range marked on the device.
2. Input Under/overshoot voltage must be –2 V > Vi < VDDn+2 V not to exceed 3.6 V maximum, with a pulse width not to exceed 20% tKC.
Rev: 1.00a 6/2003
14/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Undershoot Measurement and Timing
Overshoot Measurement and Timing
V
IH
20% tKC
V
+ 2.0 V
50%
DD
V
SS
50%
V
DD
V
– 2.0 V
SS
20% tKC
V
IL
Capacitance
o
(T = 25 C, f = 1 MHZ, V = 2.5 V)
A
DD
Parameter
Symbol
Test conditions
Typ.
Max.
Unit
pF
C
V
= 0 V
Input Capacitance
4
6
5
7
IN
IN
C
V
OUT
= 0 V
Input/Output Capacitance
pF
I/O
Note: These parameters are sample tested.
AC Test Conditions
Parameter
Conditions
V
– 0.2 V
Input high level
Input low level
DD
0.2 V
1 V/ns
/2
Input slew rate
V
Input reference level
DD
V
/2
Output reference level
Output load
DDQ
Fig. 1
Notes:
1. Include scope and jig capacitance.
2. Test conditions as specified with output loading as shown in Fig. 1
unless otherwise noted.
3. Device is deselected as defined by the Truth Table.
Output Load 1
DQ
*
50Ω
30pF
V
DDQ/2
* Distributed Test Jig Capacitance
Rev: 1.00a 6/2003
15/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
DC Electrical Characteristics
Parameter
Symbol
Test Conditions
Min
Max
Input Leakage Current
(except mode pins)
I
V = 0 to V
IN DD
–1 uA
1 uA
IL
V
≥ V ≥ V
IN
–1 uA
–1 uA
1 uA
100 uA
DD
IH
IH
I
ZZ Input Current
FTInput Current
IN1
0 V ≤ V ≤ V
IN
V
≥ V ≥ V
IN
–100 uA
–1 uA
1 uA
1 uA
DD
IL
IL
I
IN2
0 V ≤ V ≤ V
IN
I
Output Disable, V
= 0 to V
Output Leakage Current
Output High Voltage
Output Low Voltage
–1 uA
– 0.4 V
DDQ
1 uA
—
OL
OUT
DD
V
I
= –4 mA, V
= 1.6 V
V
OH
OH
DDQ
V
I
= 4 mA, V = 1.6 V
OL DD
—
0.4 V
OL
Rev: 1.00a 6/2003
16/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Rev: 1.00a 6/2003
17/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
AC Electrical Characteristics
-350
-333
-300
-250
-200
-150
Parameter
Symbol
Unit
Min
Max
—
1.8
—
—
—
—
—
4.5
—
—
—
—
—
Min
Max
—
2.0
—
—
—
—
—
4.7
—
—
—
—
—
Min
Max
—
2.2
—
—
—
—
—
5.0
—
—
—
—
—
Min
Max
—
2.3
—
—
—
—
—
5.5
—
—
—
—
—
Min
Max
—
2.7
—
—
—
—
—
6.5
—
—
—
—
—
Min
6.7
—
Max
—
3.3
—
—
—
—
—
7.5
—
—
—
—
—
Clock Cycle Time
Clock to Output Valid
Clock to Output Invalid
Clock to Output in Low-Z
Setup time
tKC
tKQ
2.85
—
3.0
—
3.3
—
4.0
—
5.0
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tKQX
1.0
1.0
1.0
0.1
4.5
—
1.0
1.0
1.0
0.1
4.7
—
1.0
1.0
1.0
0.1
5.0
—
1.0
1.0
1.2
0.2
5.5
—
1.0
1.0
1.4
0.4
6.5
—
1.0
1.0
1.5
0.5
7.5
—
Pipeline
tLZ1
tS
Hold time
tH
Clock Cycle Time
Clock to Output Valid
Clock to Output Invalid
Clock to Output in Low-Z
Setup time
tKC
tKQ
tKQX
3.0
3.0
1.3
0.3
1.0
3.0
3.0
1.4
0.4
1.0
3.0
3.0
1.4
0.4
1.3
3.0
3.0
1.5
0.5
1.3
3.0
3.0
1.5
0.5
1.3
3.0
3.0
1.5
0.5
1.5
Flow
Through
tLZ1
tS
Hold time
tH
Clock HIGH Time
tKH
Clock LOW Time
tKL
1.2
1.0
—
1.2
1.0
—
1.5
1.0
—
1.5
1.0
—
1.5
1.0
—
1.7
1.0
—
ns
ns
Clock to Output in
High-Z
tHZ1
1.8
2.0
2.2
2.3
2.7
3.0
G to Output Valid
G to output in Low-Z
G to output in High-Z
ZZ setup time
tOE
—
0
1.8
—
1.8
—
—
—
—
0
2.0
—
2.0
—
—
—
—
0
2.2
—
2.2
—
—
—
—
0
2.3
—
2.3
—
—
—
—
0
2.7
—
2.7
—
—
—
—
0
3.3
—
3.0
—
—
—
ns
ns
ns
ns
ns
ns
tOLZ1
tOHZ1
tZZS2
tZZH2
tZZR
—
5
—
5
—
5
—
5
—
5
—
5
ZZ hold time
1
1
1
1
1
1
ZZ recovery
20
20
20
20
20
20
Notes:
1. These parameters are sampled and are not 100% tested.
2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold
times as specified above.
Rev: 1.00a 6/2003
18/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Rev: 1.00a 6/2003
19/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Rev: 1.00a 6/2003
20/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
TQFP Package Drawing
θ
L
c
L1
Symbol
Description
Standoff
Min. Nom. Max
A1
A2
b
0.05
1.35
0.20
0.09
0.10
1.40
0.30
—
0.15
1.45
0.40
0.20
20.1
20.1
16.1
14.1
—
Body Thickness
Lead Width
c
Lead Thickness
D
Terminal Dimension 21.9
Package Body 19.9
Terminal Dimension 15.9
22.0
20.0
16.0
14.0
0.65
0.60
1.00
—
e
D1
E
b
E1
e
Package Body
Lead Pitch
13.9
—
L
Foot Length
Lead Length
Coplanarity
Lead Angle
0.45
—
0.75
—
L1
Y
A1
A2
E1
E
—
0.10
7°
θ
0°
—
Notes:
1. All dimensions are in millimeters (mm).
2. Package width and length do not include mold protrusion.
BPR 1999.05.18
Rev: 1.00a 6/2003
21/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
Ordering Information—GSI NBT Synchronous SRAM
2
Speed
3
1
Org
Type
Package
Status
T
Part Number
A
(MHz/ns)
1M x 18
1M x 18
GS8160ZV18AT-350
GS8160ZV18AT-333
GS8160ZV18AT-300
GS8160ZV18AT-250
GS8160ZV18AT-200
GS8160ZV18AT-150
GS8160ZV36AT-350
GS8160ZV36AT-333
GS8160ZV36AT-300
GS8160ZV36AT-250
GS8160ZV36AT-200
GS8160ZV36AT-150
GS8160ZV18AT-350I
GS8160ZV18AT-333I
GS8160ZV18AT-300I
GS8160ZV18AT-250I
GS8160ZV18AT-200I
GS8160ZV18AT-150I
GS8160ZV36AT-350I
GS8160ZV36AT-333I
GS8160ZV36AT-300I
GS8160ZV36AT-250I
GS8160ZV36AT-200I
GS8160ZV36AT-150I
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
TQFP
350/4.5
333/4.7
300/5
C
C
C
C
C
C
C
C
C
C
C
C
I
1M x 18
1M x 18
250/5.5
200/6.5
150/7.5
350/4.5
333/4.7
300/5
1M x 18
1M x 18
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
1M x 18
250/5.5
200/6.5
150/7.5
350/4.5
333/4.7
300/5
1M x 18
I
1M x 18
I
1M x 18
250/5.5
200/6.5
150/7.5
350/4.5
333/4.7
300/5
I
1M x 18
I
1M x 18
I
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
Notes:
I
I
I
250/5.5
200/6.5
150/7.5
I
I
I
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS8160ZV18A-.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow through mode-selectable by the user.
3. T = C = Commercial Temperature Range. T = I = Industrial Temperature Range.
A
A
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.00a 6/2003
22/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Preliminary
GS8160ZV18/36AT-350/333/300/250/200/150
18Mb Sync SRAM Datasheet Revision History
DS/DateRev. Code: Old;
New
Types of Changes
Format or Content
Page;Revisions;Reason
• Creation of new datasheet
8160ZV18A_r1
Rev: 1.00a 6/2003
23/23
© 2003, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
相关型号:
©2020 ICPDF网 联系我们和版权申明