GS842Z18CB-250 [GSI]
ZBT SRAM, 256KX18, 5.5ns, CMOS, PBGA119, FPBGA-119;型号: | GS842Z18CB-250 |
厂家: | GSI TECHNOLOGY |
描述: | ZBT SRAM, 256KX18, 5.5ns, CMOS, PBGA119, FPBGA-119 静态存储器 |
文件: | 总29页 (文件大小:248K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GS842Z18CB/GS842Z36CB
250 MHz–100 MHz
119-Bump BGA
Commercial Temp
Industrial Temp
4Mb Pipelined and Flow Through
Synchronous NBT SRAMs
3.3 V V
DD
2.5 V and 3.3 V V
DDQ
Because it is a synchronous device, address, data inputs, and
Features
read/ write control inputs are captured on the rising edge of the
input clock. Burst order control (LBO) must be tied to a power
rail for proper operation. Asynchronous inputs include the
sleep mode enable (ZZ) and Output Enable. Output Enable can
be used to override the synchronous control of the output
drivers and turn the RAM's output drivers off at any time.
Write cycles are internally self-timed and initiated by the rising
edge of the clock input. This feature eliminates complex off-
chip write pulse generation required by asynchronous SRAMs
and simplifies input signal timing.
• 256K x 18 and 128K x 36 configurations
• User configurable Pipeline and Flow Through mode
• NBT (No Bus Turn Around) functionality allows zero wait
read-write-read bus utilization
• Fully pin compatible with both pipelined and flow through
NtRAM™, NoBL™ and ZBT™ SRAMs
• Pin-compatible with 2Mb, 9Mb, and 18Mb devices
• 3.3 V +10%/–10% core power supply
• 2.5 V or 3.3 V I/O supply
• LBO pin for Linear or Interleave Burst mode
• Byte write operation (9-bit Bytes)
• 3 chip enable signals for easy depth expansion
• Clock Control, registered address, data, and control
• ZZ Pin for automatic power-down
• JEDEC-standard 119-bump BGA package
• RoHS-compliant package available
The GS842Z18/36CB may be configured by the user to operate
in Pipeline or Flow Through mode. Operating as a pipelined
synchronous device, in addition to the rising-edge-triggered
registers that capture input signals, the device incorporates a
rising-edge-triggered output register. For read cycles, pipelined
SRAM output data is temporarily stored by the edge triggered
output register during the access cycle and then released to the
output drivers at the next rising edge of clock.
Functional Description
The GS842Z18/36CB is a 4Mbit Synchronous Static SRAM.
GSI's NBT SRAMs, like ZBT, NtRAM, NoBL or other
pipelined read/double late write or flow through read/single
late write SRAMs, allow utilization of all available bus
bandwidth by eliminating the need to insert deselect cycles
when the device is switched from read to write cycles.
The GS842Z18/36CB is implemented with GSI's high
performance CMOS technology and is available in a JEDEC-
standard 119-bump BGA package.
Parameter Synopsis
–250
–200
–166
–150
–100
tCycle
tKQ
IDD
4.0 ns
2.5 ns
TBD
5.5 ns
3.0 ns
TBD
6.0 ns
3.5 ns
TBD
6.7 ns
3.8 ns
TBD
10 ns
4.5 ns
TBD
Pipeline
3-1-1-1
Flow
Through
2-1-1-1
tKQ
tCycle
IDD
5.5 ns
5.5 ns
TBD
6.5 ns
6.5 ns
TBD
7.0 ns
7.0 ns
TBD
7.5 ns
7.5 ns
TBD
12 ns
12 ns
TBD
Rev: 1.01 8/2011
1/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
GS842Z18C Pad Out—119-Bump BGA—Top View (Packge B)
1
2
A
3
A
A
A
4
5
A
A
A
6
A
7
A
B
C
D
E
F
V
NC
V
DDQ
DDQ
NC
NC
E2
ADV
E3
NC
NC
A
V
A
DD
DQB
NC
NC
DQB
NC
DQB
NC
V
ZQ
E1
G
V
DQPA
NC
DQA
NC
DQA
NC
SS
SS
SS
SS
SS
SS
V
V
V
V
DQA
V
V
DDQ
DDQ
G
H
J
NC
BB
NC
W
NC
DQA
DQB
V
V
NC
SS
SS
V
V
NC
V
NC
V
V
DDQ
DDQ
DD
DD
DD
K
L
NC
DQB
NC
V
CK
V
NC
DQA
NC
DQA
NC
A
DQA
SS
SS
DQB
NC
NC
CKE
A1
BA
NC
M
N
P
R
T
V
DQB
NC
V
V
V
V
V
DDQ
DDQ
SS
SS
SS
SS
SS
SS
DQB
V
V
NC
NC
NC
NC
DQPB
A
A0
DQA
NC
ZZ
LBO
A
V
FT
A
DD
A
NC
A
U
V
TMS
TDI
TCK
TDO
NC
V
DDQ
DDQ
Rev: 1.01 8/2011
2/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
GS842Z36C Pad Out— 119-Bump BGA—Top View (Package B)
1
2
A
3
A
A
A
4
5
A8
A
6
A
7
A
B
C
D
E
F
V
NC
V
DDQ
DDQ
NC
NC
E2
ADV
E3
NC
NC
A
V
A
A
DD
DQC
DQC
DQPC
DQC
DQC
DQC
DQC
V
ZQ
E1
G
V
DQPB
DQB
DQB
DQB
DQB
DQB
DQB
SS
SS
SS
SS
SS
SS
V
V
V
V
V
V
DDQ
DDQ
G
H
J
DQC
BC
NC
W
BB
DQB
DQC
V
V
DQB
SS
SS
V
V
NC
V
NC
V
V
DDQ
DDQ
DD
DD
DD
K
L
DQD
DQD
DQD
DQD
DQD
DQPD
A
V
CK
V
DQA
DQA
DQA
DQA
DQPA
A
DQA
SS
SS
DQD
BD
NC
CKE
A1
BA
DQA
M
N
P
R
T
V
V
V
V
DDQ
DDQ
SS
SS
SS
SS
SS
SS
DQD
V
V
V
V
DQA
DQD
NC
A0
DQA
NC
ZZ
LBO
A
V
FT
A
DD
NC
NC
A
NC
U
V
TMS
TDI
TCK
TDO
NC
V
DDQ
DDQ
Rev: 1.01 8/2011
3/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
GS842Z18/36C Pin Description
Symbol
A0, A1
An
Type
Description
I
I
Address field LSBs and Address Counter Preset Inputs
Address Inputs
DQA
DQB
DQC
DQD
I/O
Data Input and Output pins
BA, BB, BC, BD
I
I
I
I
I
I
I
I
I
I
I
Byte Write Enable for DQA, DQB, DQC, DQA I/Os; active low ( x36 Version)
Clock Input Signal; active high
CK
CKE
W
Clock Input Buffer Enable; active low
Write Enable. Writes all enabled bytes; active low
Chip Enable; active low
E1
Chip Enable; active high
G
Output Enable; active low
ADV
ZZ
Burst address counter advance enable; active high
Sleep Mode control; active high
FT
Flow Through or Pipeline mode; active low
Linear Burst Order mode; active low
LBO
FLXDrive Output Impedance Control
(Low = Low Impedance [High Drive], High = High Impedance [Low Drive])
ZQ
I
NC
TMS
TDI
—
No Connect
Scan Test Mode Select
Scan Test Data In
Scan Test Data Out
Scan Test Clock
I
I
TDO
TCK
VDD
O
I
I
Core power supply
VSS
VDDQ
CK
I
I
I
I/O and Core Ground
Output driver power supply
Clock Input Signal; active high
Rev: 1.01 8/2011
4/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Functional Details
Clocking
Deassertion of the Clock Enable (CKE) input blocks the Clock input from reaching the RAM's internal circuits. It may be used to
suspend RAM operations. Failure to observe Clock Enable set-up or hold requirements will result in erratic operation.
Pipelined Mode Read and Write Operations
All inputs (with the exception of Output Enable, Linear Burst Order and Sleep) are synchronized to rising clock edges. Single cycle
read and write operations must be initiated with the Advance/Load pin (ADV) held low, in order to load the new address. Device
activation is accomplished by asserting all three of the Chip Enable inputs (E1, E2, and E3). Deassertion of any one of the Enable
inputs will deactivate the device.
Function
Read
W
H
L
BA
X
BB
X
BC
X
BD
X
Write Byte “a”
Write Byte “b”
Write Byte “c”
Write Byte “d”
Write all Bytes
Write Abort/NOP
L
H
L
H
H
L
H
H
H
L
L
H
H
H
L
L
H
H
L
L
H
L
L
L
L
H
H
H
H
Read operation is initiated when the following conditions are satisfied at the rising edge of clock: CKE is asserted low, all three
chip enables (E1, E2, and E3) are active, the write enable input signal W is deasserted high, and ADV is asserted low. The address
presented to the address inputs is latched in to address register and presented to the memory core and control logic. The control
logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At
the next rising edge of clock the read data is allowed to propagate through the output register and onto the Output pins.
Write operation occurs when the RAM is selected, CKE is active and the write input is sampled low at the rising edge of clock. The
Byte Write Enable inputs (BA, BB, BC, and BD) determine which bytes will be written. All or none may be activated. A write cycle
with no Byte Write inputs active is a no-op cycle. The Pipelined NBT SRAM provides double late write functionality, matching the
write command versus data pipeline length (2 cycles) to the read command versus data pipeline length (2 cycles). At the first rising
edge of clock, Enable, Write, Byte Write(s), and Address are registered. The Data In associated with that address is required at the
third rising edge of clock.
Flow through Mode Read and Write Operations
Operation of the RAM in Flow Through mode is very similar to operations in Pipeline mode. Activation of a read cycle and the use
of the Burst Address Counter is identical. In Flow Through mode the device may begin driving out new data immediately after new
address are clocked into the RAM, rather than holding new data until the following (second) clock edge. Therefore, in Flow
Through mode the read pipeline is one cycle shorter than in Pipeline mode.
Write operations are initiated in the same way as well, but differ in that the write pipeline is one cycle shorter as well, preserving
the ability to turn the bus from reads to writes without inserting any dead cycles. While the pipelined NBT RAMs implement a
double late write protocol, in Flow Through mode a single late write protocol mode is observed. Therefore, in Flow Through mode,
address and control are registered on the first rising edge of clock and data in is required at the data input pins at the second rising
edge of clock.
Rev: 1.01 8/2011
5/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Synchronous Truth Table
Operation
Read Cycle, Begin Burst
Read Cycle, Continue Burst
NOP/Read, Begin Burst
Dummy Read, Continue Burst
Write Cycle, Begin Burst
Write Abort, Begin Burst
Write Cycle, Continue Burst
Write Abort, Continue Burst
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Continue
Sleep Mode
Type
R
Address
External
Next
CK CKE ADV
W
H
X
H
X
L
Bx E1 E2 E3
G
L
ZZ
L
L
L
L
L
L
L
L
L
L
L
L
H
L
DQ
Q
Notes
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
X
L
L
L
L
L
L
L
L
L
L
L
L
X
H
L
H
L
X
X
X
X
L
L
X
L
H
X
H
X
H
H
X
X
X
X
L
L
X
L
B
L
Q
1,10
2
1,2,10
3
R
External
Next
H
H
X
X
X
X
X
X
X
X
X
X
High-Z
High-Z
D
B
H
L
X
L
X
L
W
D
External
None
1
L
L
H
L
L
L
High-Z
D
1,3,10
B
Next
H
H
L
X
X
X
X
X
X
X
X
X
X
H
X
X
X
X
X
X
X
X
H
X
X
X
X
B
Next
H
X
X
X
X
X
X
High-Z 1,2,3,10
High-Z
D
None
D
None
L
High-Z
D
None
L
High-Z
1
4
D
None
H
X
X
X
X
X
High-Z
High-Z
-
None
Clock Edge Ignore, Stall
Current
L-H
Notes:
1. Continue Burst cycles, whether read or write, use the same control inputs. A Deselect continue cycle can only be entered into if a Deselect
cycle is executed first.
2. Dummy Read and Write abort can be considered NOPs because the SRAM performs no operation. A Write abort occurs when the W pin is
sampled low but no Byte Write pins are active so no write operation is performed.
3. G can be wired low to minimize the number of control signals provided to the SRAM. Output drivers will automatically turn off during write
cycles.
4. If CKE High occurs during a pipelined read cycle, the DQ bus will remain active (Low Z). If CKE High occurs during a write cycle, the bus
will remain in High Z.
5. X = Don’t Care; H = Logic High; L = Logic Low; Bx = High = All Byte Write signals are high; Bx = Low = One or more Byte/Write signals
are Low
6. All inputs, except G and ZZ must meet setup and hold times of rising clock edge.
7. Wait states can be inserted by setting CKE high.
8. This device contains circuitry that ensures all outputs are in High Z during power-up.
9. A 2-bit burst counter is incorporated.
10. The address counter is incriminated for all Burst continue cycles.
Rev: 1.01 8/2011
6/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Pipelined and Flow Through Read-Write Control State Diagram
D
B
Deselect
R
D
D
W
New Read
New Write
R
R
W
B
B
R
W
W
R
Burst Read
Burst Write
B
B
D
D
Key
Notes
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
2. W, R, B, and D represent input command
codes as indicated in the Synchronous Truth Table.
Current State (n)
Next State (n+1)
n
n+1
n+2
n+3
Clock (CK)
Command
ƒ
ƒ
ƒ
ƒ
Current State
Next State
Current State and Next State Definition for Pipelined and Flow Through Read/Write Control State Diagram
Rev: 1.01 8/2011
7/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Pipeline Mode Data I/O State Diagram
Intermediate
Intermediate
B
R
W
B
Intermediate
R
Data Out
(Q Valid)
High Z
(Data In)
W
D
Intermediate
D
Intermediate
W
R
High Z
B
D
Intermediate
Key
Notes
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
Transition
2. W, R, B, and D represent input command
codes as indicated in the Truth Tables.
Current State (n)
Next State (n+2)
Intermediate State (N+1)
n
n+1
n+2
n+3
Clock (CK)
Command
ƒ
ƒ
ƒ
ƒ
Intermediate
State
Current State
Next State
Current State and Next State Definition for Pipeline Mode Data I/O State Diagram
Rev: 1.01 8/2011
8/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Flow Through Mode Data I/O State Diagram
R
W
B
B
R
Data Out
(Q Valid)
High Z
(Data In)
W
D
D
W
R
High Z
B
D
Key
Notes
Input Command Code
1. The Hold command (CKE Low) is not
shown because it prevents any state change.
ƒ
Transition
2. W, R, B, and D represent input command
codes as indicated in the Truth Tables.
Current State (n)
Next State (n+1)
n
n+1
n+2
n+3
Clock (CK)
Command
Current State
Next State
Current State and Next State Definition for: Pipelined and Flow Through Read Write Control State Diagram
Rev: 1.01 8/2011
9/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Burst Cycles
Although NBT RAMs are designed to sustain 100% bus bandwidth by eliminating turnaround cycle when there is transition from
Read to Write, multiple back-to-back reads or writes may also be performed. NBT SRAMs provide an on-chip burst address
generator that can be utilized, if desired, to further simplify burst read or write implementations. The ADV control pin, when
driven high, commands the SRAM to advance the internal address counter and use the counter generated address to read or write
the SRAM. The starting address for the first cycle in a burst cycle series is loaded into the SRAM by driving the ADV pin low, into
Load mode.
Burst Order
The burst address counter wraps around to its initial state after four addresses (the loaded address and three more) have been
accessed. The burst sequence is determined by the state of the Linear Burst Order pin (LBO). When this pin is low, a linear burst
sequence is selected. When the RAM is installed with the LBO pin tied high, interleaved burst sequence is selected. See the tables
below for details.
FLXDrive™
The ZQ pin allows selection between NBT RAM nominal drive strength (ZQ low) for multi-drop bus applications and low drive
strength (ZQ floating or high) point-to-point applications. See the Output Driver Characteristics chart for details.
Mode Pin Functions
Mode Name
Pin Name
State
Function
Linear Burst
Interleaved Burst
Flow Through
Pipeline
L
Burst Order Control
LBO
H
L
Output Register Control
Power Down Control
FT
ZZ
ZQ
H or NC
L or NC
H
Active
Standby, I = I
DD SB
L
High Drive (Low Impedance)
Low Drive (High Impedance)
FLXDrive Output Impedance Control
H or NC
Note:
There are pull-up devices on the ZQ and FT pins and a pull-down device on the ZZ pin, so those input pins can be unconnected and the chip
will operate in the default states as specified in the above tables.
Rev: 1.01 8/2011
10/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Burst Counter Sequences
Linear Burst Sequence
Interleaved Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0]
A[1:0] A[1:0] A[1:0] A[1:0]
1st address
2nd address
3rd address
4th address
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
1st address
2nd address
3rd address
4th address
00
01
01
00
10
11
11
10
10
11
11
10
00
01
01
00
Note:
Note:
The burst counter wraps to initial state on the 5th clock.
The burst counter wraps to initial state on the 5th clock.
BPR 1999.05.18
8
Sleep Mode
During normal operation, ZZ must be pulled low, either by the user or by its internal pull-down resistor. When ZZ is pulled high,
the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to
low, the SRAM operates normally after 2 cycles of wake up time.
Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to I 2. The duration of
SB
Sleep Mode is dictated by the length of time the ZZ is in a high state. After entering Sleep mode, all inputs except ZZ become
disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode.
When the ZZ pin is driven high, I 2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending
SB
operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated
until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a Deselect or Read commands
may be applied while the SRAM is recovering from Sleep mode.
Sleep Mode Timing Diagram
tKH
tKC
tKL
CK
ZZ
tZZR
tZZS
tZZH
Designing for Compatibility
The GSI NBT SRAMs offer users a configurable selection between Flow Through mode and Pipeline mode via the FT signal
found on Bump R5. Not all vendors offer this option, however, most mark Bump R5 as V or V
on pipelined parts and V
DD
DDQ
SS
on flow through parts. GSI NBT SRAMs are fully compatible with these sockets.
Rev: 1.01 8/2011
11/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Absolute Maximum Ratings
(All voltages reference to V
)
SS
Symbol
VDD
VDDQ
VI/O
Description
Value
Unit
Voltage on VDD Pins
Voltage in VDDQ Pins
–0.5 to 4.6
V
V
–0.5 to 4.6
–0.5 to VDDQ +0.5 ( 4.6 V max.)
–0.5 to VDD +0.5 ( 4.6 V max.)
Voltage on I/O Pins
Voltage on Other Input Pins
Input Current on Any Pin
Output Current on Any I/O Pin
Package Power Dissipation
Storage Temperature
V
VIN
V
IIN
+/–20
+/–20
mA
mA
W
IOUT
PD
1.5
oC
oC
TSTG
–55 to 125
–55 to 125
TBIAS
Temperature Under Bias
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of
this component.
Power Supply Voltage Ranges
Parameter
Symbol
VDD3
Min.
3.0
Typ.
3.3
Max.
3.6
Unit
V
3.3 V Supply Voltage
VDD2
2.5 V Supply Voltage
2.3
2.5
2.7
V
3.3 V VDDQ I/O Supply Voltage
2.5 V VDDQ I/O Supply Voltage
VDDQ3
VDDQ2
3.0
3.3
3.6
V
2.3
2.5
2.7
V
V
Range Logic Levels
DD3
Parameter
Symbol
VIH
Min.
2.0
Typ.
—
Max.
Unit
V
VDD + 0.3
Input High Voltage
Input Low Voltage
VIL
–0.3
—
0.8
V
Note:
(max) is voltage on V
V
pins plus 0.3 V.
DDQ
IHQ
Rev: 1.01 8/2011
12/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
V
Range Logic Levels
DD2
Parameter
Symbol
VIH
Min.
Typ.
—
Max.
Unit
V
0.6*VDD
VDD + 0.3
0.3*VDD
Input High Voltage
Input Low Voltage
VIL
–0.3
—
V
Note:
(max) is voltage on V
V
pins plus 0.3 V.
DDQ
IHQ
Operating Temperature
Parameter
Symbol
Min.
Typ.
Max.
Unit
Junction Temperature
(Commercial Range Versions)
TJ
0
25
25
85
C
C
Junction Temperature
(Industrial Range Versions)*
TJ
–40
100
Note:
* The part numbers of Industrial Temperature Range versions end with the character “I”. Unless otherwise noted, all performance specifications
quoted are evaluated for worst case in the temperature range marked on the device.
Thermal Impedance
Test PCB
Substrate
JA (C°/W)
Airflow = 0 m/s
JA (C°/W)
Airflow = 1 m/s
JA (C°/W)
Airflow = 2 m/s
Package
JB (C°/W)
JC (C°/W)
100 TQFP
4-layer
28.3
27.2
25.4
—
7.1
Notes:
1. Thermal Impedance data is based on a number of samples from mulitple lots and should be viewed as a typical number.
2. Please refer to JEDEC standard JESD51-6.
3. The characteristics of the test fixture PCB influence reported thermal characteristics of the device. Be advised that a good thermal path to
the PCB can result in cooling or heating of the RAM depending on PCB temperature.
Undershoot Measurement and Timing
Overshoot Measurement and Timing
V
IH
20% tKC
V
+ 2.0 V
DD
V
SS
50%
50%
V
DD
V
– 2.0 V
SS
20% tKC
V
IL
Note:
Input Under/overshoot voltage must be –2 V > Vi < V +2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC.
DDn
Rev: 1.01 8/2011
13/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Capacitance
o
(T = 25 C, f = 1 MHZ, V = 2.5 V)
A
DD
Parameter
Symbol
CIN
Test conditions
VIN = 0 V
Typ.
Max.
Unit
pF
Input Capacitance
4
6
5
7
CI/O
VOUT = 0 V
Input/Output Capacitance
pF
Note:
These parameters are sample tested.
AC Test Conditions
Parameter
Conditions
VDD – 0.2 V
Input high level
Input low level
0.2 V
1 V/ns
VDD/2
Input slew rate
Input reference level
VDDQ/2
Output reference level
Output load
Fig. 1
Notes:
1. Include scope and jig capacitance.
2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted.
3. Device is deselected as defined by the Truth Table.
Output Load 1
DQ
*
50
30pF
V
DDQ/2
* Distributed Test Jig Capacitance
Rev: 1.01 8/2011
14/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
DC Electrical Characteristics
Parameter
Symbol
Test Conditions
Min
Max
Input Leakage Current
(except mode pins)
IIL
VIN = 0 to VDD
–1 uA
1 uA
VDD VIN VIH
0 V VIN VIH
–1 uA
–1 uA
1 uA
100 uA
IIN1
ZZ Input Current
VDD VIN VIL
0 V VIN VIL
–100 uA
–1 uA
1 uA
1 uA
IIN2
FT, ZQ Input Current
IOL
Output Disable, VOUT = 0 to VDD
IOH = –8 mA, VDDQ = 2.375 V
IOH = –8 mA, VDDQ = 3.135 V
IOL = 8 mA
Output Leakage Current
Output High Voltage
Output High Voltage
Output Low Voltage
–1 uA
1.7 V
2.4 V
—
1 uA
—
VOH2
VOH3
VOL
—
0.4 V
Operating Currents
-250
-200
-166
-150
-100
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
Parameter Test Conditions
Mode
Symbol
70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C
IDD
195
30
215
30
170
25
190
25
160
25
180
25
140
20
160
20
120
15
140
15
Pipeline
mA
mA
mA
mA
IDDQ
(x32/
x36)
IDD
Flow
Through
155
25
175
25
140
20
160
20
135
20
155
20
130
15
150
15
110
15
130
15
Device Selected;
IDDQ
All other inputs
VIH or VIL
Operating
Current
IDD
180
15
200
15
155
15
175
15
140
10
160
10
130
10
150
10
110
10
130
10
Pipeline
Output open
IDDQ
(x18)
IDD
Flow
Through
145
15
165
15
130
10
150
10
125
15
145
15
120
8
140
8
110
10
130
10
IDDQ
ISB
ISB
IDD
IDD
Pipeline
25
25
65
65
45
45
85
85
25
25
65
65
45
45
85
85
25
25
65
65
45
45
85
85
25
25
60
60
45
45
80
80
25
25
60
60
45
45
80
80
mA
mA
mA
mA
Standby
Current
ZZ VDD – 0.2 V
—
—
Flow
Through
Pipeline
Device Deselected;
All other inputs
VIH or VIL
Deselect
Current
Flow
Through
Rev: 1.01 8/2011
15/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
AC Electrical Characteristics
-250
-200
-166
-150
-100
Parameter
Symbol
Min
4.0
—
Max
—
Min
5.5
—
Max
—
Min
6.0
—
Max
—
Min Max Min Max
Clock Cycle Time
tKC
tKQ
6.7
—
—
3.8
—
10
—
—
4.5
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
Clock to Output Valid
2.5
—
3.0
—
3.5
—
Clock to Output Invalid
Pipeline
tKQX
1.5
1.5
1.2
0.2
5.5
—
1.5
1.5
1.4
0.4
6.5
—
1.5
1.5
1.5
0.5
7.0
—
1.5
1.5
1.5
0.5
7.5
—
1.5
1.5
2.0
0.5
12.0
—
tLZ1
tS
Clock to Output in Low-Z
—
—
—
—
Setup time
Hold time
—
—
—
—
tH
—
—
—
—
Clock Cycle Time
Clock to Output Valid
tKC
tKQ
tKQX
—
—
—
—
5.5
—
6.5
—
7.0
—
7.5
—
12.0 ns
Clock to Output Invalid
2.0
2.0
1.5
0.5
1.3
1.5
1.5
—
2.0
2.0
1.5
0.5
1.3
1.5
1.5
—
2.0
2.0
1.5
0.5
1.3
1.5
1.5
—
2.0
2.0
1.5
0.5
1.3
1.5
1.5
—
2.0
2.0
2.0
0.5
1.3
1.5
1.5
—
—
—
—
—
—
—
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
Flow
Through
tLZ1
tS
Clock to Output in Low-Z
Setup time
—
—
—
—
—
—
—
—
Hold time
tH
—
—
—
—
Clock HIGH Time
Clock LOW Time
Clock to Output in High-Z
G to Output Valid
G to output in Low-Z
tKH
tKL
—
—
—
—
—
—
—
—
tHZ1
tOE
2.5
2.5
—
3.0
3.0
—
3.0
3.5
—
3.0
3.8
—
5
tOLZ1
tOHZ1
tZZS2
0
0
0
0
0
—
G to output in High-Z
ZZ setup time
ZZ hold time
—
5
2.5
—
—
—
—
5
3.0
—
—
—
—
5
3.0
—
—
—
—
5
3.0
—
—
—
—
5
5
ns
ns
ns
ns
—
—
—
tZZH2
tZZR
1
1
1
1
1
ZZ recovery
20
20
20
20
20
Notes:
1. These parameters are sampled and are not 100% tested.
2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold
times as specified above.
Rev: 1.01 8/2011
16/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Pipeline Mode Timing
Write A
Read B
Suspend
tKH
Read C
tKC
Write D
Write No-op Read E
Deselect
tKL
CK
A
tH
tH
tH
tH
tH
tH
tS
A
B
C
D
E
tS
tS
tS
tS
tS
CKE
E*
ADV
W
tH
tS
Bn
tH
tLZ
tHZ
tS
tKQ
tKQX
D(A)
Q(B)
Q(C)
D(D)
Q(E)
DQ
Rev: 1.01 8/2011
17/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Flow Through Mode Timing
Write A
Write B
Write B+1 Read C
tKL
Cont
Read D
Write E
Read F
Write G
tKH
tKC
CK
CKE
E
tH
tH
tH
tH
tH
tH
tS
tS
tS
tS
tS
tS
ADV
W
Bn
A0–An
A
B
C
D
E
F
G
tKQ
tLZ
tH
tKQ
tLZ
D(B+1)
tKQX
tS
D(A)
tHZ
Q(D)
tKQX
D(G)
DQ
D(B)
Q(C)
D(E)
Q(F)
tOLZ
tOE
tOHZ
G
*Note: E = High(False) if E1 = 1 or E2 = 0 or E3 = 1
Rev: 1.01 8/2011
18/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
JTAG Port Operation
Overview
The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan
interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with V . The JTAG output
DD
drivers are powered by V
.
DDQ
Disabling the JTAG Port
It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless
clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG
Port unused, TCK, TDI, and TMS may be left floating or tied to either V or V . TDO should be left unconnected.
DD
SS
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate
from the falling edge of TCK.
TCK
Test Clock
In
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP
TMS
TDI
Test Mode Select
Test Data In
In controller state machine. An undriven TMS input will produce the same result as a logic one input
level.
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers
placed between TDI and TDO. The register placed between TDI and TDO is determined by the
In state of the TAP Controller state machine and the instruction that is currently loaded in the TAP
Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce
the same result as a logic one input level.
Output that is active depending on the state of the TAP state machine. Output changes in
Out response to the falling edge of TCK. This is the output side of the serial registers placed between
TDI and TDO.
TDO
Test Data Out
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Rev: 1.01 8/2011
19/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z,
SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register.
JTAG TAP Block Diagram
·
·
·
·
·
·
·
·
Boundary Scan Register
·
·
·
0
Bypass Register
2
1 0
Instruction Register
TDI
TDO
ID Code Register
31 30 29
2 1
0
·
· · ·
Control Signals
Test Access Port (TAP) Controller
TMS
TCK
* For the value of M, see the BSDL file, which is available at by contacting us at apps@gsitechnology.com.
Identification (ID) Register
The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in
Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM.
It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the
controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins.
Rev: 1.01 8/2011
20/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
ID Register Contents
GSI Technology
JEDEC Vendor
ID Code
Not Used
Bit # 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
0 1 1 0 1 1 0 0 1
0
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
0
Tap Controller Instruction Set
Overview
There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific
(Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be
implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load
address, data or control signals into the RAM or to preload the I/O buffers.
When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01.
When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired
instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the
TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this
device is listed in the following table.
Rev: 1.01 8/2011
21/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
JTAG Tap Controller State Diagram
Test Logic Reset
1
0
1
1
1
Run Test Idle
Select DR
Select IR
0
0
0
1
1
1
Capture DR
Capture IR
0
0
Shift DR
Shift IR
0
0
1
1
1
Exit1 DR
Exit1 IR
0
0
Pause DR
Pause IR
0
0
1
1
Exit2 DR
Exit2 IR
0
0
1
1
Update DR
Update IR
1
0
1
0
Instruction Descriptions
BYPASS
When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This
occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facili-
tate testing of other devices in the scan path.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Rev: 1.01 8/2011
22/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
RFU
These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction.
JTAG TAP Instruction Set Summary
Instruction
EXTEST
Code
000
Description
Notes
1
Places the Boundary Scan Register between TDI and TDO.
Preloads ID Register and places it between TDI and TDO.
IDCODE
001
1, 2
Captures I/O ring contents. Places the Boundary Scan Register between TDI and
SAMPLE-Z
RFU
010
011
TDO.
1
1
Forces all RAM output drivers to High-Z.
Do not use this instruction; Reserved for Future Use.
Replicates BYPASS instruction. Places Bypass Register between TDI and TDO.
SAMPLE/
PRELOAD
Captures I/O ring contents. Places the Boundary Scan Register between TDI and
TDO.
100
101
110
111
1
1
1
1
GSI
RFU
GSI private instruction.
Do not use this instruction; Reserved for Future Use.
Replicates BYPASS instruction. Places Bypass Register between TDI and TDO.
BYPASS
Places Bypass Register between TDI and TDO.
Notes:
1. Instruction codes expressed in binary, MSB on left, LSB on right.
2. Default instruction automatically loaded at power-up and in test-logic-reset state.
Rev: 1.01 8/2011
23/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
JTAG Port Recommended Operating Conditions and DC Characteristics (2.5/3.3 V Version)
Parameter
Symbol
Min.
Max.
Unit Notes
V
0.6 * V
V
+0.3
DD2
2.5 V Test Port Input High Voltage
2.5 V Test Port Input Low Voltage
3.3 V Test Port Input High Voltage
3.3 V Test Port Input Low Voltage
TMS, TCK and TDI Input Leakage Current
TMS, TCK and TDI Input Leakage Current
TDO Output Leakage Current
V
V
1
1
IHJ2
DD2
V
–0.3
0.3 * V
DD2
ILJ2
V
V
+0.3
DD3
2.0
–0.3
–300
–1
V
1
IHJ3
V
0.8
V
1
ILJ3
I
1
100
1
uA
uA
uA
V
2
INHJ
I
3
INLJ
I
–1
4
OLJ
V
Test Port Output High Voltage
1.7
—
0.4
—
5, 6
5, 7
5, 8
5, 9
OHJ
V
Test Port Output Low Voltage
—
V
OLJ
V
V
– 100 mV
DDQ
Test Port Output CMOS High
V
OHJC
V
Test Port Output CMOS Low
—
100 mV
V
OLJC
Notes:
1. Input Under/overshoot voltage must be –2 V < Vi < V
+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tTKC.
DDn
2.
V
V V
ILJ
IN
DDn
3. 0 V V V
IN
ILJn
4. Output Disable, V
= 0 to V
DDn
OUT
5. The TDO output driver is served by the V
supply.
DDQ
6.
7.
8.
9.
I
I
I
I
= –4 mA
OHJ
= + 4 mA
OLJ
= –100 uA
= +100 uA
OHJC
OLJC
JTAG Port AC Test Conditions
Parameter
Conditions
JTAG Port AC Test Load
DQ
V
– 0.2 V
Input high level
Input low level
DD
0.2 V
1 V/ns
*
50
30pF
Input slew rate
V
/2
DDQ
V
V
/2
Input reference level
DDQ
* Distributed Test Jig Capacitance
/2
Output reference level
DDQ
Notes:
1. Include scope and jig capacitance.
2. Test conditions as shown unless otherwise noted.
Rev: 1.01 8/2011
24/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
JTAG Port Timing Diagram
tTKC
tTKH
tTKL
TCK
tTH
tTH
tTS
tTS
TDI
TMS
TDO
tTKQ
tTH
tTS
Parallel SRAM input
JTAG Port AC Electrical Characteristics
Parameter
Symbol
tTKC
tTKQ
tTKH
tTKL
tTS
Min
Max
—
Unit
TCK Cycle Time
50
—
ns
ns
ns
ns
ns
ns
TCK Low to TDO Valid
TCK High Pulse Width
TCK Low Pulse Width
TDI & TMS Set Up Time
TDI & TMS Hold Time
20
—
20
20
10
10
—
—
tTH
—
Rev: 1.01 8/2011
25/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Package Dimensions—119-Bump FPBGA (Package B, Variation 2)
TOP VIEW
BOTTOM VIEW
A1
A1
S
Ø0.10
C
S
S
S
Ø0.30 C A
B
Ø0.60~0.90 (119x)
1
2
3
4
5
6
7
7
6
5
4 3
2
1
A
B
C
D
E
F
A
B
C
D
E
F
G
H
J
G
H
J
K
L
M
N
P
R
T
U
K
L
M
N
P
R
T
U
B
1.27
7.62
14±0.10
A
0.20(4x)
SEATING PLANE
C
BPR 1999.05.18
Rev: 1.01 8/2011
26/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Ordering Information—GSI NBT Synchronous SRAMs
2
Speed
3
1
Org
Type
Package
T
Part Number
J
(MHz/ns)
256K x 18
256K x 18
256K x 18
256K x 18
256K x 18
128K x 36
128K x 36
128K x 36
128K x 36
128K x 36
256K x 18
256K x 18
256K x 18
256K x 18
256K x 18
128K x 36
128K x 36
128K x 36
128K x 36
128K x 36
256K x 18
256K x 18
256K x 18
256K x 18
256K x 18
128K x 36
128K x 36
128K x 36
128K x 36
128K x 36
GS842Z18CB-250
GS842Z18CB-200
GS842Z18CB-166
GS842Z18CB-150
GS842Z18CB-100
GS842Z36CB-250
GS842Z36CB-200
GS842Z36CB-166
GS842Z36CB-150
GS842Z36CB-100
GS842Z18CB-250I
GS842Z18CB-200I
GS842Z18CB-166I
GS842Z18CB-150I
GS842Z18CB-100I
GS842Z36CB-250I
GS842Z36CB-200I
GS842Z36CB-166I
GS842Z36CB-150I
GS842Z36CB-100I
GS842Z18CGB-250
GS842Z18CGB-200
GS842Z18CGB-166
GS842Z18CGB-150
GS842Z18CGB-100
GS842Z36CGB-250
GS842Z36CGB-200
GS842Z36CGB-166
GS842Z36CGB-150
GS842Z36CGB-100
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
BGA (var. 2)
BGA (var. 2)
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
C
C
C
C
C
C
C
C
C
C
I
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
BGA (var. 2)
I
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
C
C
C
C
C
C
C
C
C
C
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS842Z36CB-100IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. C = Commercial Temperature Range. I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.01 8/2011
27/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
Ordering Information—GSI NBT Synchronous SRAMs
2
Speed
3
1
Org
Type
Package
T
Part Number
J
(MHz/ns)
256K x 18
256K x 18
256K x 18
256K x 18
256K x 18
128K x 36
128K x 36
128K x 36
128K x 36
128K x 36
GS842Z18CGB-250I
GS842Z18CGB-200I
GS842Z18CGB-166I
GS842Z18CGB-150I
GS842Z18CGB-100I
GS842Z36CGB-250I
GS842Z36CGB-200I
GS842Z36CGB-166I
GS842Z36CGB-150I
GS842Z36CGB-100I
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
NBT Pipeline/Flow Through
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
RoHS-compliant BGA (var. 2)
250/5.5
200/6.5
166/7.0
150/7.5
100/12
250/5.5
200/6.5
166/7.0
150/7.5
100/12
I
I
I
I
I
I
I
I
I
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS842Z36CB-100IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. C = Commercial Temperature Range. I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.01 8/2011
28/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS842Z18CB/GS842Z36CB
4Mb Synchronous NBT Datasheet Revision History
Types of Changes
File Name
Revision
Format or Content
• Creation of new datasheet
842ZxxC_r1
• Updated Operating Currents table
842ZxxC_r1_01
Content
Rev: 1.01 8/2011
29/29
© 2011, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
相关型号:
©2020 ICPDF网 联系我们和版权申明