HMC541LP3ETR [HITTITE]
暂无描述;
| 型号： | HMC541LP3ETR |
| 厂家： | 
HITTITE MICROWAVE CORPORATION |
| 描述： | 暂无描述 射频 微波 衰减器 |
| 文件： | 总6页 (文件大小：177K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HMC541LP3 / 541LP3E
v01.1005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Typical Applications
Features
The HMC541LP3 / HMC541LP3E is ideal for both RF
and IF applications:
0.2 dB Typical Step Error
Low Insertion Loss: 1 dB
High IP3: +50 dBm
• Cellular Infrastructure
• ISM, MMDS, WLAN, WiMAX, WiBro
• Microwave Radio & VSAT
• Test Equipment and Sensors
Single Control Line
TTL/CMOS Compatible Control
Single +5V Supply
3x3 mm SMT Package
Functional Diagram
General Description
The HMC541LP3 & HMC541LP3E are broadband
1-bit GaAs IC digital attenuators in low cost lead-
less surface mount packages. This single posi-
tive control line digital attenuator utilizes off chip
AC ground capacitors for near DC operation,
making it suitable for a wide variety of RF and IF
applications. Covering DC to 5 GHz, the insertion
loss is less than 1 dB typical. Attenuation accuracy
is excellent at 0.2 dB typical step error. The attenu-
ator also features a high IIP3 of +50 dBm. One TTL/
CMOS control input is used to select the attenuation
state. A single Vdd bias of +5V is required.
Electrical Specifications,
TA = +25° C, With Vdd = +5V & Vctl = 0/+5V (Unless Otherwise Noted)
Parameter
Frequency (GHz)
Min.
Typ.
Max.
Units
DC - 2.0 GHz
2.0 - 3.5 GHz
3.5 - 5.0 GHz
0.5
1.0
2.0
0.8
1.3
2.3
dB
dB
dB
Insertion Loss
Attenuation Range
DC - 5 GHz
10
dB
DC - 2.5 GHz
2.5 - 5.0 GHz
25
15
dB
dB
Return Loss (RF1 & RF2, All Atten. States)
Attenuation Accuracy: (Referenced to Insertion Loss)
Input Power for 0.1 dB Compression
DC - 5 GHz
0.4 Max.
27
dB
0.1 - 5.0 GHz
dBm
Input Third Order Intercept Point
(Two-Tone Input Power= 0 dBm Each Tone)
0.1 - 5.0 GHz
DC - 5 GHz
50
dBm
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
20
23
ns
ns
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 176
HMC541LP3 / 541LP3E
v01.1005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Insertion Loss
Return Loss RF1, RF2
0
0
-1
-2
-3
-4
-10
I.L.dB
10 dB
+25 C
+85 C
-40 C
-20
-30
-40
0
1
2
3
4
5
6
0
1
2
3
4
5
5
5
6
6
6
FREQUENCY (GHz)
FREQUENCY (GHz)
Normalized Attenuation
Relative Phase vs. Frequency
0
40
30
-2
-4
20
10
-6
0
-10
-20
-30
-40
-8
-10
-12
0
1
2
3
4
5
6
0
1
2
3
4
FREQUENCY (GHz)
FREQUENCY (GHz)
Bit Error vs. Frequency
Input IP3 vs. Frequency
1
60
50
40
30
20
10
0
0.6
0.2
-0.2
-0.6
-1
I.L. dB
10 dB
0
1
2
3
4
5
6
0
1
2
3
4
FREQUENCY (GHz)
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 177
HMC541LP3 / 541LP3E
v0ꢀ.ꢀ005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Bias Voltage & Current
Truth Table
Vdd = +5.0 Vdc ꢀ0%
Control Voltage Input
Attenuation State
Vdd
(VDC)
Idd (Typ.)
(mA)
Vꢀ
ꢀ0 dB
RFꢀ - RF2
+4.5
+5.0
+5.5
ꢀ.3
High
Low
Reference I.L.
ꢀ0 dB
ꢀ.5
ꢀ.7
Control Voltage
State
Bias Condition
Low
0 to +0.8V @ -5 uA Typ.
High
+2.0 to + 5.0 Vdc @ 40 uA Typ.
Note: Vdd = +5V
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 178
HMC541LP3 / 541LP3E
v0ꢀ.ꢀ005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Absolute Maximum Ratings
RF Input Power (DC - 5 GHz)
Control Voltage Range (Vꢀ)
Bias Voltage (Vdd)
+27 dBm (T = +85 °C)
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
-ꢀV to Vdd +ꢀV
+7.0 Vdc
ꢀ50 °C
Channel Temperature
Continuous Pdiss (T = 85 °C)
(derate ꢀ4.7 mW/°C above 85 °C)
0.96 W
Thermal Resistance
Storage Temperature
Operating Temperature
ESD Sensitivity (HBM)
68 °C/W
-65 to +ꢀ50 °C
-40 to +85 °C
Class ꢀB
Outline Drawing
NOTES:
ꢀ. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.ꢀ5mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
MSLꢀ [ꢀ]
Package Marking [3]
54ꢀ
XXXX
HMC54ꢀLP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
54ꢀ
XXXX
MSLꢀ [2]
HMC54ꢀLP3E
RoHS-compliant Low Stress Injection Molded Plastic
ꢀ00% matte Sn
[ꢀ] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 179
HMC541LP3 / 541LP3E
v0ꢀ.ꢀ005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Pin Descriptions
Pin Number
Function
Vdd
Description
Interface Schematic
ꢀ
Supply Voltage.
This pin is DC coupled and matched to 50 Ohm.
Blocking capacitors are required.
Select value based on lowest frequency of operation.
2, ꢀꢀ
RFꢀ, RF2
N/C
3, 4, 6, 7,
9, ꢀ0, ꢀ2,
ꢀ3, ꢀ5, ꢀ6
These pins should be connected to PCB RF ground to
maximize performance.
External capacitor to ground is required. Select value for
lowest frequency of operation. Place capacitor as close
to pins as possible.
5, 8
ACGꢀ, ACG2
ꢀ4
Vꢀ
See truth table and control voltage table.
Package bottom has an exposed metal paddle that must be
connected to RF Ground.
GND
Application Circuit
Recommended Component Values
Cꢀ - C3
C4, C5
ꢀ,000 pF ꢀ0%
330 pF ꢀ0%
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 180
HMC541LP3 / 541LP3E
v0ꢀ.ꢀ005
10 dB GaAs MMIC 1-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 5 GHz
5
Evaluation PCB
List of Material for Evaluation PCB 111317 [1]
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be con-
nected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
Item
Description
Jꢀ - J2
J3 - J5
Cꢀ - C3
C4 - C5
PCB Mount SMA Connector
DC Connector
ꢀ000 pF Capacitor, 0402 Pkg.
330 pF Capacitor, 0402 Pkg.
HMC54ꢀLP3 / HMC54ꢀLP3E
Digital Attenuator
Uꢀ
[2]
PCB
ꢀꢀꢀ290 Evaluation PCB
[ꢀ] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 181
相关型号：
HMC542BLP4E
Variable Attenuator, 0MHz Min, 4000MHz Max, 2.3dB Insertion Loss-Max, 4 X 4 MM, ROHS COMPLIANT, LEADLESS, PLASTIC, SMT, QFN-24
HITTITE
©2020 ICPDF网 联系我们和版权申明