4AV15F [HONEYWELL]

Installation Instructions; 安装说明


型号：	4AV15F
厂家：	Honeywell
描述：	Installation Instructions 安装说明
文件：	总4页 (文件大小：77K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ISSUE 2

Installation Instructions for the

4AV Series Vane Sensors

PK 87605

GENERAL INFORMATION

4AV Hall effect vane sensors include a Hall effect

sensor and a magnet in a common package. They

are operated by passing a ferrous vane through the

gap between the magnet and the sensor.

With no vane in the gap, the output is Operated

(conducting). With the vane in the gap, the output is

Released (non-conducting). The vane actuator is

annealed low carbon cold rolled steel, type AISI

1018 or lower in carbon. Minimum recommended

vane dimensions are required to ensure operating

characteristics will be met.

PERSONAL INJURY

DO NOT USE these products as safety or

emergency stop devices or in any other application

where failure of the product could result in personal

injury.

Failure to comply with these instructions could

result in death or serious injury.

ELECTRICAL CHARACTERISTICS

Supply

Current

Output

Voltage

Output

Catalog

Listing

Lead

Termination

Voltage

Sink Current

All listings

Length

All Listings

All listings

4AV15F

4AV16F

24 AWG Wire

.015 X .025 PCB

5.50 ± 0.25

7.45 ± 0.25

13.15 ± 0.50

18.15 ± 0.50

22.00 ± 0.50

0.140

18.5 mA Max

@ -40 °C

0.4 V Max

@125 °C

0.1 typical

4.5 VDC

through

40 mA Max

15.25 mA typical

4AV17F

26.5 VDC

Dual output

sink currents

are summed

to reach total.

4AV18F

11.75 mA

@25 °C

typical

0.075 V

4AV19F

@25 °C typical

4AV20F

4AV20F-T1*

.025 X .025

Connector

AMP Terminal

Block 103323-4

4AV20F-T2**

.025 X .025

Connector

Molex Terminal

Block 22-05-3041

*Will mate with AMP Connector Housing 87499-8, not supplied

**Will mate with Molex Connector Housing 2695/6471, not supplied

VANE DIMENSIONS (mm/in)

Thickness Min.

Window

Min.

Tooth

Min. Tooth

Depth

1,0/0.4

1,6/.06

10,2/.40

6,3/.25

9,27/.365

Sensing and Control

ISSUE 2 PK 87605

4AV Series Vane Sensors

MECHANICAL CHARACTERISTICS (mm/in)

Series Left

Operate

Left

Release

Left

Diff.

Right

Operate

Right

Release

Right

Diff

L-R

Diff.

4AV*

5,4/.213

6,0/.237

0,6/.024 8,6/.337

7,9/.313

0,6/.024 2,5/.100

*Operating characteristics of the 4AV are adjusted to produce a .100 + .010 dimension between

the Operate point on one side of the package to the Release point on the other side. The actuator

can be designed to produce a specific pulse width for timing or sequencing operations.

MOUNTING DIMENSIONS (for reference only)

CAUTION

PRODUCT DAMAGE

• Do not exceed electrical specifications.

• Do not mis-wire the output connection.

• Do not reverse supply voltage polarity.

• Handle terminals with care.

Failure to comply with these instructions may

result in product damage.

Mates with AMP housing 87499-8

2 Honeywell • Sensing and Control

For application help: call 1-800-537-6945

ISSUE 2 PK 87605

4AV Series Vane Sensors

SOLDERING

CLEANING

Hand Cleaning

CAUTION

PRODUCT DAMAGE

Clean areas with a 50-50 mixture of isopropyl

alcohol and clean tap water. Dry in a 71 °C (160 °F)

oven for 10-15 minutes, preferably in a non-

circulating oven. This will remove all moisture from

the assembly, which must be done before electrical

testing, or application.

• Ensure iron tip is clean when soldering.

Failure to comply with these instructions may result in

product damage.

Hand Soldering

The following is recommended:

1. Flux: Rosin Base

2. Solder: Kester #44 60-40 rosin core, or

equivalent.

Machine Cleaning *

Detergent: London Chemical Company

Loncoterge 444-NRT6 or equivalent. Equipment:

Dee Electric Aqueous Cleaner or equivalent. The

following is reccommended:

3. Soldering Iron: Type; Weller, Model TC-552, 55

watt or equivalent.

4. Tip Size: 3mm (.118 in.) Diameter x 30mm

(1.182 in.) long

1. Wash Section: 55 °C (130 °F) maximum water

5. Tip Temperature: 288°C (550°F) max

temperature, 5 to 10% maximum solution soft

water, low pressure nozzles (60 psi) on top

spray and high pressure nozzles (120 psi) on

bottom spray, conveyor speed 3 feet/minute

minimum. Recirculating tank.

6. Terminal Contact Time: 6 seconds max.

Wave Soldering

The following is recommended:

1. Flux: London Chemical Co. Loncoflux - 106A35

or equivalent

2. Preheat: Preheaters should be set to give 95 °C

(200 °F) on the top (component side) of printed

circuit board just prior to board entering the

wave. (May have to be adjusted depending

upon board thickness.)

2. Rinse Section #1: Clean tap water up to 25

grains hard, salt free (to minimize possibility of

corrosion), unheated, non-recirculating, with

high pressure nozzles (120 psi).

3. Rinse Section #2: Clean deionized water only,

high pressure nozzles (120 psi), unheated and

non-recirculating.

4. Air Knife Section: To remove excessive amounts

of water.

5. Drying Section: 71°C (160 °F) drying for 10-15

3. Solder Temperature: 260 °C (500 °F) max.;

preferably 252 °C to 260 °C (485 °F to 500 °F).

4. Speed: Set conveyor speed to approximately

4.5 feet/minute (1,37 meters/minute).

5. Printed circuit board requires rigid support

during wave soldering.

minutes, preferably in a non-circulating conveyor

oven.

* In this cleaning system, the detergent in the wash

section removes the non-polar contaminants, the first rinse

removes the detergent solution, and the deionized water

rinse removes the polar contaminants. The air knife and

dryer remove all the moisture from the assembly, which

must be done before electrical testing or application.

CAUTION

PRODUCT DAMAGE

• Ensure cleaner does not come in contact with sensor If

other cleaning methods are selected for removal of flux

residue.

Failure to comply with these instructions may result in

product damage.

For application help: call 1-800-537-6945

Honeywell • Sensing and Control 3

ISSUE 2 PK 87605

4AV Series Vane Sensors

EXAMPLE WIRING DIAGRAMS

WARRANTY/REMEDY

While we provide application assistance

Honeywell warrants goods of its manufacture as

being free of defective materials and faulty

workmanship. Contact your local sales office for

warranty information. If warranted goods are

personally, through our literature and the Honeywell

web site, it is up to the customer to determine the

suitability of the product in the application.

For application assistance, current specifications,

returned to Honeywell during the period of coverage, or name of the nearest Authorized Distributor,

Honeywell will repair or replace without charge those contact a nearby sales office. Or call:

items it finds defective. The foregoing is Buyer’s sole 1-800-537-6945 USA

remedy and is in lieu of all other warranties,

expressed or implied, including those of

merchantability and fitness for a particular

purpose.

1-800-737-3360 Canada

1-815-235-6847 International

FAX

1-815-235-6545 USA

INTERNET

Specifications may change without notice. The

information we supply is believed to be accurate and www.honeywell.com/sensing

reliable as of this printing. However, we assume no

responsibility for its use.

info.sc@honeywell.com

Sensing and Control

Honeywell Inc.

11 West Spring Street

Freeport, Illinois 61032

www.honeywell.com/sensing

Printed with Soy Ink

on 50% Recycled Paper

PK 87605-2-EN IL50 GLO 0303 Printed in USA

4AV15F [HONEYWELL]

相关型号：

4AV16F

4AV17F

4AV18F

4AV19F

4AV20F

4AV20F-T1

4AV20F-T2

4AV20F-T2-FE

4AX103K1

4AX103K2

4AX103K3

4AX103K4