ASDX005D44D [HONEYWELL]
Peizoresistive Sensor, Differential, 0Psi Min, 5Psi Max, 2%, 0.50-4.50V, Rectangular, Through Hole Mount, DIP-8;
| 型号： | ASDX005D44D |
| 厂家： | 
Honeywell |
| 描述： | Peizoresistive Sensor, Differential, 0Psi Min, 5Psi Max, 2%, 0.50-4.50V, Rectangular, Through Hole Mount, DIP-8 传感器 换能器 |
| 文件： | 总4页 (文件大小：263K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Microstructure Pressure Sensors
0 psi to 1 psi through 0 psi to 100 psi
ASDX Series
FEATURES
• ASIC enhanced output
• Wide compensated
temperature range 0 °C to
85 °C [32 °F to 185 °F]
• Available in absolute,
differential and gage types
• Pressure ranges from
0 psi to 1 psi through
0 psi to 100 psi
• Accuracy 2 % max. Volts
Full Scale
• Quantization step of 3 mV
• Response time 8 ms
TYPICAL APPLICATIONS
• Flow calibrators
The ASDX series is an amplified version of Honeywell’s proven performer
and industry leading SDX series sensor. The amplified ASDX sensor’s
footprint is slightly larger than the SDX but it offers a high level output (4.0
Vdc span) on a very cost-effective basis. This series is fully calibrated and
temperature compensated with on-board Application Specific Integrated
Circuitry (ASIC). They are intended for use with non-corrosive, non-ionic
working fluids; such as air and dry gases.
• Ventilation and air flow
monitors
• Gas flow instrumentation
• Dialysis equipment
• Sleep apnea monitoring
and therapy equipment
• Barometry
• HVAC controls
• Pneumatic controls
Sensors are available to measure absolute, differential, and gage pressures.
The absolute devices have an internal vacuum reference and an output
voltage proportional to absolute pressure. Differential devices allow
application of pressure to either side of the sensing diaphragm and can be
used for gauge or differential measurements.
All ASDX devices are accurate to within 2.0 % full scale, designed for
operation from a single 5.0 Vdc supply and are manufactured in accordance
with ISO 9001 standards.
WARNING
PERSONAL INJURY
DO NOT USE these
products as safety or
emergency stop devices or
in any other application
where failure of the product
could result in personal
injury.
Failure to comply with
these instructions could
result in death or serious
injury.
WARNING
MISUSE OF DOCUMENTATION
• The information presented in this product sheet is for reference only. Do
not use this document as a product installation guide.
• Complete installation, operation, and maintenance information is provided
in the instructions supplied with each product.
Failure to comply with these instructions could result in death or
serious injury.
Sensing and Control
Microstructure Pressure Sensors
0 psi to 1 psi through 0 psi to 100 psi
ASDX Series
BLOCK DIAGRAM
ELECTRICAL CONNECTIONS(2) PIN OUT
ASDXxxxD4*
ASDXxxxG2*
ASDXxxxA2*
* N/C means no connection, connecting to ground will damage to sensor.
SPECIFICATIONS (Maximum Ratings)
Supply Voltage (Vs)*
Maximum Supply Voltage*
Consumption Current
Output Current - Sink
Output Current - Source
Lead Temperature
4.75 Vdc to 5.25 Vdc
6.50 Vdc (max.)
6 mA (typ.)
2 mA (max.)
2 mA (max.)
2 Sec to 4 Sec @ 250 °C [482 °F]
*Note: The sensor is not reverse polarity protected. Incorrect application of excitation voltage or ground to the wrong pin can cause
electrical failure. Application of supply voltage above the maximum can cause electrical failure.
ENVIRONMENTAL SPECIFICATIONS (ALL DEVICES)
Temperature Ranges:
Compensated:
Operating:
Storage:
0 °C to 85 °C [32 °F to 185 °F]
-20 °C to 105 °C [-4 °F to 221 °F]
-40 °C to 125 °C [-40 °F to 257 °F]
10 g at 20 Hz to 2000 Hz
50 g for 11 ms
Vibration:
Shock:
Life:
1 million cycles minimum
PRESSURE RANGE SPECIFICATIONS
Part No.
Pressure Range
0 psi to 1 psi
0 psi to 5 psi
0 psi to 15 psi
0 psi to 30 psi
0 psi to 100 psi
Burst Pressure (3)
5 psi
Sensitivity
4.00 V/psi
0.80 V/psi
0.267 V/psi
0.133 V/psi
0.040 V/psi
ASDX001
ASDX005
ASDX015
ASDX030
ASDX100
20 psi
30 psi
60 psi
150 psi
2 Honeywell • Sensing and Control
Microstructure Pressure Sensors
0 psi to 1 psi through 0 psi to 100 psi
ASDX Series
PERFORMANCE SPECIFICATIONS(4)
Characteristic
Symbol
Voff
Min.
Typ.
0.500
4.00
4.500
–
Max.
Units
Vdc
Vdc
Vdc
% Vfs
ms
Zero Pressure Offset
Full Scale Span(5)
Output at FS Pressure
Accuracy(6)
Response Time(7)
Quantization Step(8)
0.420
0.580
Vfss
Vfso
–
4.420
4.580
2.0
–
–
–
–
8
3
–
mV
SPECIFICATION NOTES
Note 1: Capacitor 220 nF required between +Vs and GND pin.
Note 2: Pins 4, 5, 6, 7 and 8 are internal device connections and should not be connected to external circuitry or ground.
Note 3: If maximum burst pressure is exceeded, even momentarily, the package may leak or burst, or the pressure sensing die may
fracture.
Note 4: Reference Conditions (unless otherwise noted): Supply voltage, VS=5.0 0.01 Vdc; TA=25 °C [77 °F]. Output is ratiometric within
the supply voltage range (Vs).
Note 5: Span is the algebraic difference between the output voltage at the specified pressure and the output at zero pressure. Span is
ratiometric to the supply voltage.
Note 6: Accuracy is the combined errors from offset and span calibration, linearity, pressure hysteresis, and temperature effects.
Linearity is the measured deviation based on a straight line.
Hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing
pressure.
Calibration errors include the deviation of offset and full scale from nominal values.
Note 7: Response time for a 0 psi to full-scale pressure step change, 10 % to 90 % rise time.
Note 8: The smallest change in the output voltage, given any change in pressure.
PRESSURE TRANSDUCER PERFORMANCE CHARACTERISTICS
Error Band Multiplier Over -20 °C to 105 °C [-4 °F to 221 °F]
ORDERING INFORMATION - PART NUMBER DESCRIPTION
ASDX XXX
XX
4X
Sensor Series
Device Output
4R = 0.5 Vdc to 4.5 Vdc
4D = 2.5 ±2.0 Vdc*
4H = 0.25 Vdc to 4.25 Vdc*
4M = 0.2 Vdc to 4.7 Vdc*
For example:
Pressure Ranges
001 = 0 psi to 1 psi
005 = 0 psi to 5 psi
Part #ASDX015A24R=ASDX
device 15 psi absolute,
A2 Package, 0.5 Vdc to 4.5 Vdc
Output
D, G
D, G
015 = 0 psi to 15 psi D, G, A
030 = 0 psi to 30 psi D, G, A
100 = 0 psi to 100 psi D, G, A
Package Style and Type
A2 = DIP Package Absolute
D4 = DIP Package Differential
D2, G2 = DIP Package, Gage
* Contact Honeywell for additional information.
Honeywell • Sensing and Control 3
Microstructure Pressure Sensors
ASDX Series
0 to 1 psi through 0 to 100 psi
TO ORDER, USE THE FOLLOWING PART NUMBER(S)
Pressure Range
Absolute
Gauge
Differential
Bidirectional
0 psi to 1 psi
0 psi to 5 psi
0 psi to 15 psi
0 psi to 30 psi
0 psi to 100 psi
–
–
ASDX001G24R
ASDX005G24R
ASDX015G24R
ASDX030G24R
ASDX100G24R
ASDX001D44R
ASDX005D44R
ASDX015D44R
ASDX030D44R
ASDX100D44R
ASDX001D44D
ASDX005D44D
ASDX015D44D
ASDX030D44D
ASDX100D44D
ASDX015A24R
ASDX030A24R
ASDX100A24R
DIMENSIONAL DRAWINGS - For Reference Only mm [in]
D4 Package
G2 Package
A2 Package
WARRANTY/REMEDY
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
For application assistance, current specifications, or name of the
nearest Authorized Distributor, contact a nearby sales office. Or call:
1-800-537-6945 USA
1-800-737-3360 Canada
1-815-235-6847 International
FAX
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Contact your local sales
office for warranty information. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair or
replace without charge those items it finds defective. The foregoing
is Buyer’s sole remedy and is in lieu of all other warranties,
expressed or implied, including those of merchantability and
fitness for a particular purpose.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
1-815-235-6545 USA
INTERNET
www.honeywell.com/sensing
info.sc@honeywell.com
Sensing and Control
www.honeywell.com/sensing
Honeywell
11 West Spring Street
Freeport, Illinois 61032
008090-3-EN IL50 GLO 1105 Printed in USA
Copyright 2005 Honeywell International Inc. All Rights Reserved.
相关型号：
ASDX005G24R
Peizoresistive Sensor, Gage, 0Psi Min, 5Psi Max, 2%, 0.50-4.50V, Rectangular, Through Hole Mount, DIP-8
HONEYWELL
©2020 ICPDF网 联系我们和版权申明