HFE4050-013/ABA [HONEYWELL]
LED Emitter, 810nm Min, 885nm Max, SMA Connector, Through Hole Mount;
| 型号： | HFE4050-013/ABA |
| 厂家： | 
Honeywell |
| 描述： | LED Emitter, 810nm Min, 885nm Max, SMA Connector, Through Hole Mount 光纤 |
| 文件： | 总6页 (文件大小：318K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HFE4050-01X/XXX
High Power Fiber Optic LED
FEATURES
•
High power LED sends 410 µW into 100/140 micron
fiber
•
•
•
•
High speed: 85 MHz
Rated to 100 mA forward current operation
Wave solderable
Designed to operate with Honeywell fiber optic
receivers
•
Mounting options
SMA single hole
ST single hole
SMA PCB
ST PCB
SMA 4 hole
DESCRIPTION
The HFE4050-01X/XXX is a high radiance GaAlAs
850 nanometer LED optimized for coupling into small
fiber core diameters at a forward current up to 100 mA.
The patented "Caprock"™ LED chip combines high power
coupling with wide bandwidth. The peak wavelength is
matched for use with Honeywell silicon fiber optic
detectors and receivers.
APPLICATION
The HFE4050-01X/XXX is a high radiance LED
packaged in a fiber optic connector that aligns the optical
axis of the base component to the axis of the optical fiber.
Data rates can vary from DC to above 85 MHz depending
upon component application. The LED converts electrical
current into optical power that can be used in fiber optic
communications. As the current varies (typically from 10
to 100 mA), the light intensity increases proportionally.
The HFE4050-01X/XXX LED provides the maximum
amount of radiance for the amount of forward current in
the industry. A 0.25 mm diameter glass microlens over
the "Caprock"™ junction collimates the light, increasing
the intensity. Thus, greater power is directed toward
standard fiber optic cables.
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible.
226
h
HFE4050-01X/XXX
High Power Fiber Optic LED
ELECTRO-OPTICAL CHARACTERISTICS(TÙ = -40¡C to +100¡C unless otherwise stated)
TYP
PARAMETER
Fiber Coupled Power [À]
SYMBOL MIN
MAX UNITS
TEST CONDITIONS
PÞÙ
I¸ = 100 mA, 50/125 micron, [Á]
0.20 NA fiber, T = 25¡C [Â]
HFE4050-013/XXX
30
40
µW
dBm
µW
-15.2 -14.0
20
Over Temp. Range
-17.0
50
dBm
µW
HFE4050-014/XXX
70
-13.0 -11.5
33
dBm
µW
Over Temp. Range
-14.8
dBm
Forward Voltage
Reverse Voltage
Peak Wavelength
Spectral Bandwidth (FWHM)
Response Time
V¸
Báß
æÎ
1.50
1.0
810
1.85
5.0
850
50
2.25
885
V
V
nm
nm
ns
I¸ = 100 mA
Iß = 10 µA
I¸ = 50 mA DC
êæ
I¸ = 50 mA DC
1 V Prebias, 100 mA peak [Â]
T = 25¡C, 10-90%
T = 25¡C, 90-10%
Analog Bandwidth
tß
t¸
BWE
6
6
85
10
10
MHz
I¸ = 100 mA DC, sinusoidal
modulation [Â]
PÞ Temperature Coefficient
êPÞ/êT
-0.02
dB/¡C
I¸ = 100 mA
(over 25 to 125¡C)
DC
Vß = 0 V, f = 1 MHz
Heat sinked [Â]
Not heat sinked
Series Resistance
Capacitance
Thermal Resistance
rØ
C
4.0
70
150
300
í
pF
¡C/W
¡C/W
Notes
1. Dash numbers indicate power output. See ORDER GUIDE.
2. HFE4050-01X/XXX is tested using a 10 meter length of 50/125 µm dia. fiber cable, terminated in a precision ST ferrule. Actual
coupled power values may vary due to alignment procedures and/or receptacle and fiber tolerances.
3. HFE4050-01X/XXX must be heat sinked for continuous I¸ > 100 mA operation for maximum reliability (i.e. mounted in a metal
connector with thermally conductive epoxy).
ABSOLUTE MAXIMUM RATINGS
FIBER INTERFACE
(25¡C Free-Air Temperature unless otherwise noted)
Honeywell LEDs are designed to interface with
multimode fiber with sizes ranging from 50/125 to
200/230 microns. Honeywell performs final tests using
50/125 micron core fiber. All multimode fiber optic cables
between 50/125 and 200/230 should operate with similar
excellent performance. See table for typical powers.
Storage temperature
-65 to + 150¡C
-55 to + 125¡C
260¡C , 10 s
100 mA
Case operating temperature
Lead solder temperature
Continuous forward current
(heat sinked)
TYPICAL COUPLED POWER (µW/dBm) @ I¸= 100 mA
Reverse voltage
1 V @ 10 µA
Dia.
Index
Step
N.A.
---
-013
-014
Stresses greater than those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect
reliability.
8/125
1.0/-30.0
40/-14.0
88/-10.6
232/-6.4
1.8/-27.5
70/-11.5
153/-8.1
406/-3.9
50/125
62.5/125
100/140
Graded 0.20
Graded 0.28
Graded 0.29
Honeywell reserves the right to make
changes in order to improve design and
227
h
supply the best products possible.
HFE4050-01X/XXX
High Power Fiber Optic LED
ORDER GUIDE
WARNING
Under certain application conditions, the infrared optical output
of this device may exceed Class 1 eye safety limits, as defined
by IEC 825-1 (1993-11). Do not use magnification (such as a
microscope or other focusing equipment) when viewing the
device's output.
Description
Catalog Listing
Standard screening, typical power HFE4050-013/XXX
out 25 µW
Standard screening, typical power HFE4050-014/XXX
out 33 µW
CAUTION
The inherent design of this component causes
it to be sensitive to electrostatic discharge
(ESD). To prevent ESD-induced damage
and/or degradation to equipment, take normal
ESD precautions when handling this product.
MOUNTING OPTIONS
substitute XXX with one of the following 3
letter combinations
SMA single hole
ST single hole
SMA PCB
ST PCB
SMA 4 hole
- AAA
- BAA
- ABA
- BBA
- ADA
Dimensions on page 203
Fig. 1
Typical Optical Power Output vs Forward
Fig. 2
Typical Spectral Output vs Wavelength
FIBER021.GRA
FIBER105.GRA
Current
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible.
228
h
HFE4050-01X/XXX
High Power Fiber Optic LED
Fig. 3
Typical Optical Power Output vs Case
FIBER023.GRA
Temperature
All Performance Curves Show Typical Values
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible.
229
h
European Connectorized
LEDs/Transmitters
Honeywell LED/transmitter components are available in the following connector styles. Each style has a three-digit reference
used in the order guides.
SMA SINGLE HOLE MOUNTING (REF.: AAA)
ST SINGLE HOLE MOUNTING (REF.: BAA)
SMA PCB MOUNTING (REF.: ABA)
Honeywell Optoelectronics reserves the right to make
changes at any time in order to improve design and
supply the best products possible.
203
European Connectorized
LEDs/Transmitters
ST PCB MOUNTING (REF.: BBA)
SMA 4 HOLE MOUNTING (REF.: ADA)
Honeywell Optoelectronics reserves the right to make
changes at any time in order to improve design and
supply the best products possible.
204
相关型号：
HFE4050-014
LED Emitter, 810nm Min, 885nm Max, ST Connector, TO-46, Through Hole Mount, METAL CAN, TO-46 HEADER, 3 PIN
HONEYWELL
©2020 ICPDF网 联系我们和版权申明