HSCDAND006BDAA5_技术文档

TruStability^®Board Mount

Pressure Sensors

HSC Series—High Accuracy, Compensated/Ampliﬁed

1.6 mbar to 10 bar | 160 Pa to 1 MPa | 0.5 inH₂O to 150 psi

Digital or Analog Output

Datasheet

TruStability^®Board Mount Pressure Sensors

The TruStability^®High Accuracy Silicon Ceramic (HSC) Series is a piezoresistive silicon pressure sensor offering a ratiometric

analog or digital output for reading pressure over the specified full scale pressure span and temperature range.

The HSC Series is fully calibrated and temperature compensated for sensor offset, sensitivity, temperature effects, and non-

linearity using an on-board Application Specific Integrated Circuit (ASIC). Calibrated output values for pressure are updated at

approximately 1 kHz for analog and 2 kHz for digital.

The HSC Series is calibrated over the temperature range of 0 °C to 50 °C [32 °F to 122 °F]. The sensor is characterized for

operation from a single power supply of either 3.3 Vdc or 5.0 Vdc.

These sensors measure absolute, gage, or differential pressures. The absolute versions have an internal vacuum reference

and an output value proportional to absolute pressure. Gage versions are referenced to atmospheric pressure and provide an

output proportional to pressure variations from atmosphere. Differential versions allow measurement of pressure between the

two pressure ports.

The TruStability^®pressure sensors are intended for use with non-corrosive, non-ionic gases, such as air and other dry gases.

Available options extend the performance of these sensors to non-corrosive, non-ionic liquids for pressure ranges above

40 mbar | 4 kPa | 20 inH₂O.

All products are designed and manufactured according to ISO 9001 standards.

,

What makes our sensors better?

• Stability and reliability

Table of Contents

Features and Beneﬁts. . . . . . . . . . . . . . . . . . 3-5

Potential Applications. . . . . . . . . . . . . . . . . . . . 6

General Speciﬁcations . . . . . . . . . . . . . . . . . 7-8

Analog Operating Speciﬁcations . . . . . . . . . . . 9

Digital Operating Speciﬁcations. . . . . . . . . . . 10

Transfer Function Limits . . . . . . . . . . . . . . . . . 11

Total Error Band Values . . . . . . . . . . . . . . . . . 12

Nomenclature and Order Guide . . . . . . . . . . . 13

Pressure Range Speciﬁcations

• Industry-leading accuracy of 0.25 ꢀFSS BFSꢁ

• Port and housing options simplify integration

• Wide pressure range, from 1.ꢂ mbar to 10 bar |

1ꢂ0 Pa to 1 MPa | 0.5 inH₂O to 150 psi

• Small package size

• Extremely low power consumption

1.6 mbar to 10 bar . . . . . . . . . . . . . . . . . . 14

160 Pa to 1 MPa. . . . . . . . . . . . . . . . . . . . 15

0.5 inH₂O to 150 psi. . . . . . . . . . . . . . . . . 16

Available Standard Conﬁgurations. . . . . . .17-18

Dimensional Drawings

DIP Packages. . . . . . . . . . . . . . . . . . . . . 19-21

SMT Packages . . . . . . . . . . . . . . . . . . . 21-24

SIP Packages. . . . . . . . . . . . . . . . . . . . . 24-29

Pinouts, PCB Layouts. . . . . . . . . . . . . . . . . . . 30

TruStability^®Board Mount Pressure Sensors

Portfolio Overview . . . . . . . . . . . . . . . . . . . . . 31

Additional Information. . . . . . . . . . . . . . . . . . . 32

stability • accuracy • flexibility • small size

sensing.honeywell.com

2

PꢀꢁPꢀꢂꢃꢄAꢀꢅ Hꢁꢆꢃꢅwꢃꢇꢇ ꢄꢃCHꢆꢁꢇꢁꢈꢅ

Features

and Beneﬁts

Combines high sensitivity with high overpressure and burst pressure while

providing industry leading stability—performance factors that are difficult to

achieve in the same product; this gives the customer more flexibility in sensor

implementation and reduces the customer design requirements for protecting the

sensor without sacrificing the ability to sense very small changes in pressure.

PꢀꢁꢄꢃCꢄꢃD Bꢅ MUꢇꢄꢂPꢇꢃ ꢈꢇꢁBAꢇ PAꢄꢃꢆꢄS

ꢂꢆDUSꢄꢀꢅ-ꢇꢃADꢂꢆꢈ ꢇꢁꢆꢈ-ꢄꢃꢀM SꢄABꢂꢇꢂꢄꢅ

Even after long-term use and thermal extremes, the sensor’s stability remains best

in class:

• Minimizes system calibration needs.

• Improves system performance.

• Helps support system uptime by minimizing the need to service or replace the

sensor during its application life.

ꢄꢁꢄAꢇ ꢃꢀꢀꢁꢀ BAꢆD (ꢄꢃB)

Honeywell specifies TEB—the most comprehensive, clear, and meaningful

measurement—that provides the sensor’s true performance over a compensated

range of 0 °C to 50 °C [32 °F to 122 °F] (see Figure 1):

• Minimizes individually testing and calibrating every sensor, decreasing

manufacturing time and process costs.

• Improves system accuracy.

• Provides enhanced sensor interchangeability—there is minimal part-to-part

variation in accuracy.

All Possible Errors

Offset

+

Full Scale Span

+

Pressure Non-Linearity

+

=

Accuracy

Pressure Hysteresis

Total

=

+

Error Band

Pressure Non-Repeatability

+

Thermal Effect on Offset

+

Thermal Effect on Span

+

Thermal Hysteresis

Figure 1. TEB Components for TruStability^®Board Mount Pressure Sensors

sensing.honeywell.com

3

ꢂꢆDUSꢄꢀꢅ-ꢇꢃADꢂꢆꢈ ACCUꢀACꢅ

Features

and Beneﬁts

Extremely tight accuracy of 0.25 ꢀFSS BFSꢁ (Full Scale Span Best Fit Straight

ꢁine) reduces software needed to correct system inaccuracies, minimizing system

design time:

• Avoids additional customer calibration.

• Helps to improve system efficiency.

• Often simplifies software development.

HꢂꢈH BUꢀSꢄ PꢀꢃSSUꢀꢃS

• Promotes system reliability and reduces potential system downtime.

• Can simplify the design process.

HꢂꢈH wꢁꢀkꢂꢆꢈ PꢀꢃSSUꢀꢃ ꢀAꢆꢈꢃS

Allows ultra-low pressure sensors to be used continuously well above the

calibrated pressure range.

ꢂꢆDUSꢄꢀꢅ-ꢇꢃADꢂꢆꢈ fꢇꢃxꢂBꢂꢇꢂꢄꢅ

Modular, flexible design with many package styles (with the same industry-

leading stability), pressure ports, and options simplify integration into the device

manufacturer’s application.

wꢂDꢃ vAꢀꢂꢃꢄꢅ ꢁf PꢀꢃSSUꢀꢃ ꢀAꢆꢈꢃS

From 1.ꢂ mbar to 10 bar | 1ꢂ0 Pa to 1 MPa | 0.5 inH₂O to 150 psi provide

support for many unique applications.

MꢃꢃꢄS ꢂPC/JꢃDꢃC J-SꢄD-020D.1 MꢁꢂSꢄUꢀꢃ SꢃꢆSꢂꢄꢂvꢂꢄꢅ ꢇꢃvꢃꢇ

1 ꢀꢃqUꢂꢀꢃMꢃꢆꢄS

• Allows the customer to avoid the thermal and mechanical damage during

solder reflow attachment and/or repair that lesser rated products would incur.

• Allows unlimited floor life when stored as specified (<30 ºC/85 ꢀRH),

simplifying storage and reducing scrap.

• Never requires lengthy bakes prior to reflow.

• Stable and usable shortly after reflow process allows for lean manufacturing.

ꢁPꢄꢂꢁꢆAꢇ ꢂꢆꢄꢃꢀꢆAꢇ DꢂAꢈꢆꢁSꢄꢂC fUꢆCꢄꢂꢁꢆS

• May reduce the need for redundant sensors in the system.

• Detects most internal failures including burst sensors.

ꢃꢆꢃꢀꢈꢅ ꢃffꢂCꢂꢃꢆꢄ

Extremely low power consumption (less than 10 mW, typ.):

• Reduces system power requirements.

• Enables extended battery life.

• Optional sleep mode available upon special request.

sensing.honeywell.com

4

ꢁUꢄPUꢄ: ꢀAꢄꢂꢁMꢃꢄꢀꢂC AꢆAꢇꢁꢈ; ꢂ²C- ꢁꢀ SPꢂ-CꢁMPAꢄꢂBꢇꢃ

14-Bꢂꢄ DꢂꢈꢂꢄAꢇ ꢁUꢄPUꢄ (Mꢂꢆ. 12-Bꢂꢄ SꢃꢆSꢁꢀ ꢀꢃSꢁꢇUꢄꢂꢁꢆ)

Features

and Beneﬁts

Accelerates performance through reduced conversion requirements and the

convenience of direct interface to microprocessors.

SMAꢇꢇ Sꢂzꢃ

Miniature 10 mm x 10 mm [0.39 in x 0.39 in] package is very small when

compared to many board mount pressure sensors:

• Occupies less area on the PCB.

• Typically allows for easy placement on crowded PCBs or in small devices.

ꢀꢃACH AꢆD ꢀꢁHS CꢁMPꢇꢂAꢆꢄ

ꢇꢂqUꢂD MꢃDꢂA ꢁPꢄꢂꢁꢆ

• Provides robustness in environments with condensing humidity.

• Compatible with a variety of non-ionic fluids.

• Available for pressure ranges above 40 mbar | 4 kPa | 20 inH₂0.

sensing.honeywell.com

5

Potential Applications

MꢃDꢂCAꢇ

• Aꢂꢀfꢇꢁw MꢁꢆꢂꢄꢁꢀS

• AꢆꢃSꢄHꢃSꢂA MACHꢂꢆꢃS

• BꢇꢁꢁD AꢆAꢇꢅSꢂS MACHꢂꢆꢃS

• ꢈAS CHꢀꢁMAꢄꢁꢈꢀAPHꢅ

• ꢈAS fꢇꢁw ꢂꢆSꢄꢀUMꢃꢆꢄAꢄꢂꢁꢆ

• kꢂDꢆꢃꢅ DꢂAꢇꢅSꢂS MACHꢂꢆꢃS

• ꢁxꢅꢈꢃꢆ CꢁꢆCꢃꢆꢄꢀAꢄꢁꢀS

• PꢆꢃUMAꢄꢂC CꢁꢆꢄꢀꢁꢇS

• ꢀꢃSPꢂꢀAꢄꢁꢀꢅ MACHꢂꢆꢃS

• SꢇꢃꢃP APꢆꢃA ꢃqUꢂPMꢃꢆꢄ

• vꢃꢆꢄꢂꢇAꢄꢁꢀS

• SPꢂꢀꢁMꢃꢄꢃꢀS

• ꢆꢃBUꢇꢂzꢃꢀS

• HꢁSPꢂꢄAꢇ ꢀꢁꢁM Aꢂꢀ PꢀꢃSSUꢀꢃ

ꢂꢆDUSꢄꢀꢂAꢇ

• BAꢀꢁMꢃꢄꢀꢅ

• fꢇꢁw CAꢇꢂBꢀAꢄꢁꢀS

• ꢈAS CHꢀꢁMAꢄꢁꢈꢀAPHꢅ

• ꢈAS fꢇꢁw ꢂꢆSꢄꢀUMꢃꢆꢄAꢄꢂꢁꢆ

• HvAC

• ꢇꢂfꢃ SCꢂꢃꢆCꢃS

• PꢆꢃUMAꢄꢂC Cꢁꢆꢄꢀꢁꢇ

• vAv (vAꢀꢂABꢇꢃ Aꢂꢀ vꢁꢇUMꢃ) Cꢁꢆꢄꢀꢁꢇ

• CꢇꢁꢈꢈꢃD HvAC fꢂꢇꢄꢃꢀ DꢃꢄꢃCꢄꢂꢁꢆ

• HvAC ꢄꢀAꢆSMꢂꢄꢄꢃꢀS

• ꢂꢆDꢁꢁꢀ Aꢂꢀ qUAꢇꢂꢄꢅ

sensing.honeywell.com

6

General Speciﬁcations

ꢄable 1. Absolute Maꢉimum ꢀatings¹

Characteristic

Min.

-0.3

Maꢉ.

ꢂ.0

Unit

Vdc

V

Supply voltage (V_supply

)

Voltage on any pin

V_supply+ 0.3

Digital interface clock frequency:

I²C

SPI

400

800

kHz

100

50

ESD susceptibility (human body model)

Storage temperature

3

—

kV

-40 [-40]

85 [185]

°C [°F]

Soldering time and temperature:

lead solder temperature (SIP, DIP)

peak reflow temperature (SMT)

4 s max. at 250 °C [482 °F]

15 s max. at 250 °C [482 °F]

¹Absolute maximum ratings are the extreme limits the device will withstand without damage.

ꢄable 2. ꢃnꢊironmental Speciꢋications

Characteristic

Parameter

Humidity:

gases only (See “Options N and D” in Figure 4.)

0ꢀ to 95ꢀ RH, non-condensing

liquid media (See “Options T and V” in Figure 4.)

100ꢀ condensing or direct liquid media on Port 1

MIꢁ-STD-202G, Method 204D, Condition B (15 g, 10 Hz to 2 Hz)

MIꢁ-STD-202G, Method 213B, Condition C (100 g, ꢂ ms duration)

1 million pressure cycles minimum

Vibration

Shock

ꢁife¹

J-STD-020-D.1 Moisture Sensitivity ꢁevel 1

(unlimited shelf life when stored at <30 °C/85 ꢀ RH)

Solder reflow

¹ꢁife may vary depending on specific application in which the sensor is utilized.

sensing.honeywell.com

7

General Speciﬁcations

ꢄable 3. wetted Materials¹

Component

Port 1 (Pressure Port)

high temperature polyamide

alumina ceramic

Port 2 (ꢀeꢋerence Port)

high temperature polyamide

alumina ceramic

Ports and covers

Substrate

Adhesives

epoxy, silicone

Electronic components

ceramic, silicon, glass, solder

silicon, glass, gold

¹Contact Honeywell Customer Service for detailed material information.

CAUTION

PRODUCT DAMAGE FOR SENSORS WITH LIQUID MEDIA OPTION (ONLY AVAILABLE 60 MBAR |

6 KPA | 1 PSI AND ABOVE)

• Ensure liquid media is applied to Port 1 only; Port 2 is not compatible with liquids.

• Ensure liquid media contains no particulates. All TruStability® sensors are dead-ended devices. Particulates can accumulate

inside the sensor, causing damage or affecting sensor output.

• Recommend that the sensor be positioned with Port 1 facing downwards; any particulates in the system are less likely to enter

and settle within the pressure sensor if it is in this position.

• Ensure liquid media does not create a residue when dried; build-up inside the sensor may affect sensor output. Rinsing of a

dead-ended sensor is difﬁcult and has limited effectiveness for removing residue.

• Ensure liquid media are compatible with wetted materials. Non-compatible liquid media will degrade sensor performance and

may lead to sensor failure.

Failure to comply with these instructions may result in product damage.

ꢄable 4. Sensor Pressure ꢄypes

Pressure ꢄype

Absolute

Description

Output is proportional to the difference between applied pressure and a built-in vacuum reference.

Output is proportional to the difference between the pressures applied to each port (Port 1 – Port 2).

Output is proportional to the difference between applied pressure and atmospheric (ambient) pressure.

Differential

Gage

sensing.honeywell.com

8

Analog Operating Speciﬁcations

ꢄable 5. Analog ꢁperating Speciꢋications

Characteristic

Min.

ꢄyp.

Maꢉ.

Unit

Supply voltage (V_supply):^{1, 2, 3}

pressure ranges >ꢂ0 mbar | ꢂ kPa | 1 psi:

3.0

4.75

3.3

5.0

3.ꢂ

5.25

3.3 Vdc

5.0 Vdc

Vdc

pressure ranges <40 mbar | 4 kPa | 20 inH₂O:

3.3 Vdc

5.0 Vdc

3.27

4.95

3.3

5.0

3.33

5.05

Supply current:

3.3 Vdc

5.0 Vdc

—

2.1

2.7

2.8

3.5

mA

Operating temperature range⁴

Compensated temperature range⁵

Startup time (power up to data ready)

Response time

-20 [-4]

0 [-32]

—

1

85 [185]

50 [122]

5

°C [°F]

ms

—

ms

Clipping limit:

upper

lower

—

2.5

—

97.5

—

ꢀVsupply

Accuracy^ꢂ

ꢀFSS BFSꢁ⁸

ꢀFSS

—

0.25

—

Output resolution

0.03

Orientation sensitivity ( 1 g):^{7, 9}

pressure ranges <40 mbar | 4 kPa | 20 inH₂O

pressure ranges <2.5 mbar | 250 Pa | 1 inH₂O

—

0.1

0.2

—

ꢀFSS⁸

¹Sensors are either 3.3 Vdc or 5.0 Vdc based on the catalog listing selected.

²Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specified operating voltage.

³The sensor is not reverse polarity protected. Incorrect application of supply voltage or ground to the wrong pin may cause electrical failure.

⁴Operating temperature range: The temperature range over which the sensor will produce an output proportional to pressure.

⁵Compensated temperature range: The temperature range over which the sensor will produce an output proportional to pressure within the specified

performance limits.

^ꢂAccuracy: The maximum deviation in output from a Best Fit Straight ꢁine (BFSꢁ) fitted to the output measured over the pressure range at 25 °C [77 °F]. Includes

all errors due to pressure non-linearity, pressure hysteresis, and non-repeatability.

⁷Orientation sensitivity: The maximum change in offset of the sensor due to a change in position or orientation relative to Earth’s gravitational field.

⁸Full Scale Span (FSS): The algebraic difference between the output signal measured at the maximum (Pmax.) and minimum (Pmin.) limits of the pressure range.

(See Figure 4 for ranges.)

⁹Insignificant for pressure ranges above 40 mbar | 4 kPa | 20 inH₂O.

sensing.honeywell.com

9

Digital Operating Speciﬁcations

ꢄable 6. Digital ꢁperating Speciꢋications

Characteristic

Min.

ꢄyp.

Maꢉ.

Unit

1, 2, 3

:

)

Supply voltage (V_supply

pressure ranges >ꢂ0 mbar | ꢂ kPa | 1 psi:

3.0

4.75

3.3

5.0

3.ꢂ

5.25

3.3 Vdc

5.0 Vdc

Vdc

pressure ranges <40 mbar | 4 kPa | 20 inH₂O:

3.3 Vdc

5.0 Vdc

3.27

4.95

3.3

5.0

3.33

5.05

Supply current:

3.3 Vdc

5.0 Vdc

—

3.1

3.7

3.9

4.ꢂ

mA

Operating temperature range⁴

Compensated temperature range⁵

Startup time (power up to data ready)

Response time

-20 [-4]

0 [-32]

—

85 [185]

50 [122]

3

°C [°F]

ms

—

0.4ꢂ

—

ms

SPI/I²C voltage level:

low

high

—

80

—

20

—

ꢀVsupply

Pull up on SDA/MISO, SCꢁ/SCꢁK, SS

Accuracy^ꢂ

1

—

kOhm

ꢀFSS BFSꢁ⁸

bits

—

12

0.25

—

Output resolution

Orientation sensitivity ( 1 g):^{7, 9}

pressure ranges <40 mbar | 4 kPa | 20 inH₂O

pressure ranges <2.5 mbar | 250 Pa | 1 inH₂O

—

0.1

0.2

—

ꢀFSS⁸

¹Sensors are either 3.3 Vdc or 5.0 Vdc based on the catalog listing selected.

²Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specified operating voltage.

³The sensor is not reverse polarity protected. Incorrect application of supply voltage or ground to the wrong pin may cause electrical failure.

⁴Operating temperature range: The temperature range over which the sensor will produce an output proportional to pressure.

⁵Compensated temperature range: The temperature range over which the sensor will produce an output proportional to pressure within the specified

performance limits.

^ꢂAccuracy: The maximum deviation in output from a Best Fit Straight ꢁine (BFSꢁ) fitted to the output measured over the pressure range at 25 °C [77 °F]. Includes

all errors due to pressure non-linearity, pressure hysteresis, and non-repeatability.

⁷Orientation sensitivity: The maximum change in offset of the sensor due to a change in position or orientation relative to Earth’s gravitational field.

⁸Full Scale Span (FSS): The algebraic difference between the output signal measured at the maximum (Pmax.) and minimum (Pmin.) limits of the pressure range.

(See Figure 4 for ranges.)

⁹Insignificant for pressure ranges above 40 mbar | 4 kPa | 20 inH₂O.

ꢄable 7. Sensor ꢁutput at Signiꢋicant Percentages (Digital versions ꢁnly)

% ꢁutput

Digital Counts (decimal)

Digital Counts (heꢉ)

0x0000

0

10

0

1ꢂ38

8192

1474ꢂ

1ꢂ383

0x0ꢂꢂꢂ

50

90

100

0x2000

0x399A

0x3FFF

sensing.honeywell.com

10

Transfer Function Limits

figure 2. ꢄransꢋer function ꢇimits¹

Analog versions

Compensated Pressure Range

100

90

80

70

60

50

40

30

20

10

0

Ideal

1% Total Error Band

0

7

9

1

2

3

4

5

6

8

10

max.

P_min.

P

Pressure (example unit)

0.8 x Vsupply

x (Pressure_applied– P_min.) + 0.10 x Vsupply

Output (V) =

P

_max.– P_min.

Digital versions

Compensated Pressure Range

100

90

80

70

60

50

40

30

20

10

0

Ideal

1% Total Error Band

0

7

9

1

2

3

4

5

6

8

10

max.

P_min.

P

Pressure (example unit)

80%

_max.– P_min.

Output (% of 2¹⁴counts) =

x (Pressure_applied– P_min.) + 10%

P

¹Transfer Function “A” is shown. See Figure 4 for other available transfer function options.

sensing.honeywell.com

11

Total Error Band Values

figure 3. ꢄotal ꢃrror Band values ꢋor full Scale Span Pressure ꢀanges

Differential

Gage

10 bar | 1 MPa

150 psi

Low to Mid

Pressure

Low to Mid

Pressure

± psi

60 mbar | 6 kPa

20 inH₂O

Ultra-Low

Pressure

Ultra-Low

Pressure

40 mbar | 4 kPa

25 mbar | 2.5 kPa

16 mbar | 1.6 kPa

25 mbar | 2.5 kPa

10 inH₂O

16 mbar | 1.6 kPa

10 mbar | 1 kPa

4 mbar | 400 Pa

5 inH₂O

10 mbar | 1 kPa

6 mbar | 600 Pa

2 inH₂O

0 inH₂O

2 inH₂O

0 inH₂O

2.5 mbar | 250 Pa

1.6 mbar | 160 Pa

0 mbar | 0 Pa

0%

Ideal

±±

±±.5

±ꢀ

±±.5

±ꢀ

Accuracy (%FSS)

Total Error Band (%FSS)

±ꢁ

±ꢀ.5

sensing.honeywell.com

12

Nomenclature and Order Guide

figure 4. ꢆomenclature and ꢁrder ꢈuide

For example, HSCDNNN150PGAA3 deꢀnes an HSC Series TruStability^®Pressure Sensor, DIP package, NN pressure port, no

special options,150 psi gage pressure range, analog output type, 10% to 90% of Vsupply transfer function, 3.3 Vdc supply voltage.

H S C

D

N N

N

1 5 0 P G

A

3

Supply Voltage

Product Series

3.3 Vdc

3

5

5.0 Vdc

High Accuracy, Compensated/Amplified

HSC

Transfer Function¹

Package

10% to 90% of Vsupply (analog), 2¹⁴counts (digital)

5% to 95% of Vsupply (analog), 2¹⁴counts (digital)

5% to 85% of Vsupply (analog), 2¹⁴counts (digital)

4% to 94% of Vsupply (analog), 2¹⁴counts (digital)

A

B

C

F

DIP (Dual Inline Pin)

D

M

S

SMT (Surface Mount Technology)

SIP (Single Inline Pin)

Output Type²

Pressure Port

DIP

SMT

SIP

Analog

I²C, Address 0x48

I²C, Address 0x58

I²C, Address 0x68

I²C, Address 0x78

A

S

2

3

4

5

6

7

SPI

No ports

NN

No ports

NN

AA

AN

LN

FF

I²C, Address 0x28

I²C, Address 0x38

Pressure Range^{3, 4}

1.6 mbar to 10 bar

Dual axial

barbed ports,

opposite sides

0.5 inH₂O to 150 psi

160 Pa to 1 MPa

Absolute

0 psi to 15 psi

Single axial

barbed port

Single axial

barbed port

Single axial

barbed port

0 bar to 1 bar

0 bar to 1.6 bar

0 bar to 2.5 bar

0 bar to 4 bar

0 bar to 6 bar

0 bar to 10 bar

0 kPa to 100 kPa

001BA

1.6BA

2.5BA

004BA

006BA

010BA

100KA

015PA

AN

LN

0 kPa to 160 kPa

0 kPa to 250 kPa

0 kPa to 400 kPa

0 kPa to 600 kPa

0 kPa to 1 MPa

0 psi to 30 psi

0 psi to 60 psi

0 psi to 100 psi

0 psi to 150 psi

160KA

250KA

400KA

600KA

001GA

030PA

060PA

100PA

150PA

Single axial

barbless port

Single axial

barbless port

Single axial

barbless port

LN

Fastener

mount, dual

axial barbed

ports, opposite

sides

Differential

160 Pa

250 Pa

400 Pa

600 Pa

1 kPa

Differential

0.5 inH₂O

1 inH₂O

2 inH₂O

4 inH₂O

5 inH₂O

10 inH₂O

20 inH₂O

30 inH₂O

1 psi

1.6MD 1.6 mbar

2.5MD 2.5 mbar

004MD 4 mbar

006MD 6 mbar

010MD 10 mbar

016MD 16 mbar

025MD 25 mbar

040MD 40 mbar

060MD 60 mbar

100MD 100 mbar

160MD 160 mbar

250MD 250 mbar

400MD 400 mbar

600MD 600 mbar

0.5ND

001ND

002ND

004ND

005ND

010ND

020ND

030ND

001PD

005PD

015PD

030PD

060PD

160LD

250LD

400LD

600LD

001KD

1.6KD

2.5KD

004KD

006KD

010KD

016KD

025KD

040KD

060KD

100KD

160KD

250KD

400KD

Fastener

mount, single

axial barbed

port

FN

GN

NB

RN

RR

DR

JN

JJ

Ribbed

fastener mount,

single axial

barbed port

008B

1.6 kPa

2.5 kPa

4 kPa

Fastener

mount, dual

axial ports,

same side

6 kPa

Single radial

barbed port

Single radial

barbed port

Single radial

barbed port

10 kPa

16 kPa

25 kPa

40 kPa

60 kPa

100 kPa

160 kPa

250 kPa

400 kPa

5 psi

15 psi

RN

RR

DR

JN

JJ

RN

30 psi

Dual radial

barbed ports,

same side

Dual radial

barbed ports,

same side

Dual radial

barbed ports,

RR

60 psi

same side

Dual radial

1 bar

001BD

1.6BD

2.5BD

004BD

barbed ports,

opposite sides

barbed ports,

opposite sides

DR

1.6 bar

2.5 bar

4 bar

opposite sides

Single radial

barbless port

Single radial

barbless port

JN

barbless port

Gage

0 Pa to 250 Pa

0 Pa to 400 Pa

0 Pa to 600 Pa

0 kPa to 1 kPa

0 kPa to 1.6 kPa

0 kPa to 2.5 kPa

0 kPa to 4 kPa

0 kPa to 6 kPa

0 kPa to 10 kPa

0 kPa to 16 kPa

0 kPa to 25 kPa

0 kPa to 40 kPa

0 kPa to 60 kPa

0 kPa to 100 kPa

0 kPa to 160 kPa

0 kPa to 250 kPa

0 kPa to 400 kPa

0 kPa to 600 kPa

0 kPa to 1 MPa

2.5MG

004MG

006MG

010MG

016MG

025MG

040MG

060MG

100MG

160MG

250MG

400MG

600MG

001BG

1.6BG

250LG

400LG

600LG

001KG

1.6KG

2.5KG

004KG

006KG

010KG

016KG

025KG

040KG

060KG

100KG

160KG

250KG

400KG

600KG

001GG

001NG

002NG

004NG

005NG

010NG

020NG

030NG

001PG

005PG

015PG

030PG

060PG

100PG

150PG

0 mbar to 2.5 mbar

0 mbar to 4 mbar

0 mbar to 6 mbar

0 mbar to 10 mbar

0 mbar to 16 mbar

0 mbar to 25 mbar

0 mbar to 40 mbar

0 mbar to 60 mbar

0 mbar to 100 mbar

0 mbar to 160 mbar

0 mbar to 250 mbar

0 bar to 400 mbar

0 bar to 600 mbar

0 bar to 1 bar

0 inH₂O to 1 inH₂O

0 inH₂O to 2 inH₂O

0 inH₂O to 4 inH₂O

0 inH₂O to 5 inH₂O

0 inH₂O to 10 inH₂O

0 inH₂O to 20 inH₂O

0 inH₂O to 30 inH₂O

0 psi to 1 psi

Dual radial

barbless ports,

same side

barbless ports,

same side

JJ

same side

Fastener

mount, dual

radial barbed

ports, same

side

HH

HN

Fastener

mount, single

radial barbed

port

0 psi to 5 psi

Manifold

mount, outer

MN _{diameter seal}

0 psi to 15 psi

0 psi to 30 psi

Manifold

0 psi to 60 psi

mount, inner

SN

0 psi to 100 psi

0 psi to 150 psi

diameter seal

Options^{5, 6}

0 bar to 1.6 bar

2.5BG

0 bar to 2.5 bar

Dry gases only, no diagnostics

N

004BG

006BG

010BG

0 bar to 4 bar

Dry gases only, diagnostics on

D

T

V

0 bar to 6 bar

Liquid media on Port 1, no diagnostics

Liquid media on Port 1, diagnostics on

0 bar to 10 bar

¹The transfer function limits define the output of the sensor at a given pressure input. By specifying Pmin. and Pmax., the output at Pmin. and Pmax., the complete transfer function of the sensor is defined. See

the graphical representations of the transfer function in Figure 2. For other available transfer functions contact Honeywell Customer Service.

²SPI output function is not available in SIP package.

³Custom pressure ranges are available. Contact Honeywell Customer Service for more information.

⁴See the explanation of sensor pressure types in Table 4.

⁵See the CAUTION in this document.

^ꢂOptions T and V are only available on pressure ranges ꢂ0 mbar to 10 bar | ꢂ kPa to 1 MPa | 1 psi to 150 psi.

sensing.honeywell.com

13

Pressure Range Speciﬁcations

1.6 mbar to 10 bar

ꢄable 8. Pressure ꢀange Speciꢋications ꢋor 1.6 mbar to 10 bar

Pressure

ꢀange

(see

ꢄotal ꢃrror

Band aꢋter

Auto-zero⁶

(%fSS)

ꢇong-term

Stability

1000 hr, 25 °C

(%fSS)

Common

Mode

ꢄotal ꢃrror

Band⁵

(%fSS)

ꢀange

worꢌing

ꢁꢊer

Burst

Unit

Pressure¹

Pressure²

Pressure³

Pressure⁴

figure 4)

Absolute

001BA

1.ꢂBA

2.5BA

004BA

00ꢂBA

010BA

0

1

1.ꢂ

2.5

4

ꢂ

10

bar

-

2

4

ꢂ

8

17

4

8

1ꢂ

17

-

1ꢀ

-

0.25ꢀ

Diꢋꢋerential

1.ꢂMD

2.5MD

004MD

00ꢂMD

010MD

01ꢂMD

025MD

040MD

0ꢂ0MD

100MD

1ꢂ0MD

250MD

400MD

ꢂ00MD

001BD

1.ꢂBD

-1.ꢂ 1.ꢂ

-2.5 2.5

mbar

335

375

435

-

ꢂ75

750

850

1400

2000

4

1000

1250

1350

1000

2500

4000

8

3450

5450

10450

10000

10

2.5ꢀ

2ꢀ

1.5ꢀ

1ꢀ

1.75ꢀ

1.25ꢀ

0.75ꢀ

0.5ꢀ

-

0.5ꢀ

0.35ꢀ

0.25ꢀ

-4

-ꢂ

4

ꢂ

-10

-1ꢂ

-25

-40

-ꢂ0

10

1ꢂ

25

40

ꢂ0

-100 100 mbar

-1ꢂ0 1ꢂ0 mbar

-250 250 mbar

-400 400 mbar

-ꢂ00 ꢂ00 mbar

-1

1

bar

-1.ꢂ 1.ꢂ

-2.5 2.5

-4.0 4.0

8

1ꢂ

17

10

2.5BD

004BD

ꢈage

2.5MG

004MG

00ꢂMG

010MG

01ꢂMG

025MG

040MG

0ꢂ0MG

100MG

1ꢂ0MG

250MG

400MG

ꢂ00MG

001BG

1.ꢂBG

0

2.5

4

ꢂ

10

1ꢂ

25

40

ꢂ0

mbar

335

375

-

ꢂ75

750

850

1400

2000

2

1000

1250

1000

2500

4000

4

3450

5450

10000

10

3ꢀ

2ꢀ

1.5ꢀ

1ꢀ

2ꢀ

1.25ꢀ

1ꢀ

0.75ꢀ

0.5ꢀ

-

0.5ꢀ

0.35ꢀ

0.25ꢀ

100 mbar

1ꢂ0 mbar

250 mbar

400 mbar

ꢂ00 mbar

1

1.ꢂ

2.5

4

bar

4

8

17

8

1ꢂ

17

10

1ꢂ

17

2.5BG

004BG

00ꢂBG

010BG

ꢂ

10

17

¹Working pressure: The maximum pressure that may be applied to any port of the sensor in continuous use. This pressure may be outside the operating pressure range

limits (Pmin. to Pmax.) in which case the sensor may not provide a valid output until presssure is returned to within the operating pressure range. Tested to 1 million cycles,

minimum.

²Overpressure: The maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the operating pressure range. Exposure

to higher pressures may cause permanent damage to the product. Unless otherwise specified this applies to all available pressure ports at any temperature with the operating

temperature range.

³Burst pressure: The maximum pressure that may be applied to any port of the product without causing escape of pressure media. Product should not be expected to function after

exposure to any pressure beyond the burst pressure.

⁴Common mode pressure: The maximum pressure that can be applied simultaneously to both ports of a differential pressure sensor without causing changes in specified

performance.

⁵Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure range. Includes all errors due to offset, full scale

span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span, and thermal hysteresis (see Figure 1).

^ꢂTotal Error Band after Auto-Zero: The maximum deviation from the ideal transfer function over the entire compensated pressure range at a constant temperature and supply voltage

for a minimum of 24 hours after an auto-zero operation. Includes all errors due to full scale span, pressure non-linearity, pressure hysteresis, and thermal effect on span.

sensing.honeywell.com

14

Pressure Range Speciﬁcations

160 Pa to 1 MPa

ꢄable 9. Pressure ꢀange Speciꢋications ꢋor 160 Pa to 1 MPa

Pressure

ꢀange

(see

ꢄotal ꢃrror

Band aꢋter

Auto-zero⁶

(%fSS)

ꢇong-term

Stability

1000 hr, 25 °C

(%fSS)

Common

Mode

ꢄotal ꢃrror

Band⁵

(%fSS)

ꢀange

worꢌing

ꢁꢊer

Burst

Unit

Pressure¹

Pressure²

Pressure³

Pressure⁴

figure 4)

Absolute

100KA

1ꢂ0KA

250KA

400KA

ꢂ00KA

001GA

0

100

1ꢂ0

250

400

ꢂ00

1

kPa

MPa

-

200

400

ꢂ00

800

1700

400

800

1ꢂ00

1700

-

1ꢀ

-

0.25ꢀ

Diꢋꢋerential

1ꢂ0ꢁD

250ꢁD

400ꢁD

ꢂ00ꢁD

001KD

1.ꢂKD

2.5KD

004KD

00ꢂKD

010KD

01ꢂKD

025KD

040KD

0ꢂ0KD

100KD

1ꢂ0KD

250KD

400KD

-1ꢂ0 1ꢂ0

-250 250

-400 400

-ꢂ00 ꢂ00

Pa

33500

37.5

43.5

-

ꢂ7500

75

85

140

200

400

800

1ꢂ00

100000

125

135

100

250

400

800

1ꢂ00

1700

345000

545

1045

1000

2.5ꢀ

2ꢀ

1.5ꢀ

1ꢀ

1.75ꢀ

1.25ꢀ

0.75ꢀ

0.5ꢀ

-

0.5ꢀ

0.35ꢀ

0.25ꢀ

-1

1

kPa

-1.ꢂ 1.ꢂ

-2.5 2.5

-4

-ꢂ

4

ꢂ

-10

-1ꢂ

-25

-40

-ꢂ0

10

1ꢂ

25

40

ꢂ0

-100 100

-1ꢂ0 1ꢂ0

-250 250

-400 400

ꢈage

250ꢁG

400ꢁG

ꢂ00ꢁG

001KG

1.ꢂKG

0

250

400

ꢂ00

1

1.ꢂ

2.5

4

ꢂ

10

1ꢂ

25

Pa

33500

33.5

37.5

-

ꢂ7500

ꢂ7.5

75

85

140

200

400

800

1700

1.7

100000

100

125

100

345000

345

545

3ꢀ

2ꢀ

1.5ꢀ

1ꢀ

2ꢀ

1.25ꢀ

1ꢀ

0.75ꢀ

0.5ꢀ

-

0.5ꢀ

0.35ꢀ

0.25ꢀ

kPa

MPa

2.5KG

004KG

00ꢂKG

010KG

01ꢂKG

025KG

040KG

0ꢂ0KG

100KG

1ꢂ0KG

250KG

400KG

ꢂ00KG

001GG

545

1000

1ꢂ00

1700

1.7

250

400

40

ꢂ0

100

1ꢂ0

250

400

ꢂ00

1

800

1ꢂ00

1700

1.7

¹Working pressure: The maximum pressure that may be applied to any port of the sensor in continuous use. This pressure may be outside the operating pressure range

limits (Pmin. to Pmax.) in which case the sensor may not provide a valid output until presssure is returned to within the operating pressure range. Tested to 1 million cycles,

minimum.

²Overpressure: The maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the operating pressure range. Exposure

to higher pressures may cause permanent damage to the product. Unless otherwise specified this applies to all available pressure ports at any temperature with the operating

temperature range.

³Burst pressure: The maximum pressure that may be applied to any port of the product without causing escape of pressure media. Product should not be expected to function after

exposure to any pressure beyond the burst pressure.

⁴Common mode pressure: The maximum pressure that can be applied simultaneously to both ports of a differential pressure sensor without causing changes in specified

performance.

⁵Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure range. Includes all errors due to offset, full scale

span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span, and thermal hysteresis (see Figure 1).

^ꢂTotal Error Band after Auto-Zero: The maximum deviation from the ideal transfer function over the entire compensated pressure range at a constant temperature and supply voltage

for a minimum of 24 hours after an auto-zero operation. Includes all errors due to full scale span, pressure non-linearity, pressure hysteresis, and thermal effect on span.

sensing.honeywell.com

15

Speciﬁcations

0.5 inH₂O to 150 psi

ꢄable 10. Pressure ꢀange Speciꢋications ꢋor 0.5 inH₂ꢁ to 150 psi

Pressure

ꢀange

(see

Common

Mode

ꢄotal ꢃrror

Band aꢋter

ꢇong-term

Stability

ꢄotal ꢃrror

Band⁵

(%fSS)

ꢀange

worꢌing

ꢁꢊer

Burst

Unit

Pressure¹

Pressure²

Pressure³

Pressure⁴

Auto-zero⁶1000 hr, 25 °C

figure 4)

(%fSS)

Absolute

015PA

030PA

0ꢂ0PA

100PA

150PA

0

15

30

ꢂ0

100

150

psi

-

30

ꢂ0

120

250

ꢂ0

-

1ꢀ

-

0.25ꢀ

120

240

250

Diꢋꢋerential

0.5ND

001ND

002ND

004ND

005ND

010ND

020ND

030ND

001PD

005PD

015PD

030PD

0ꢂ0PD

-0.5 0.5

inH₂O

psi

135

150

175

-

270

300

350

10

30

ꢂ0

120

250

415

500

550

15

1400

2200

4200

150

250

3ꢀ

2ꢀ

1ꢀ

2ꢀ

1.25ꢀ

0.75ꢀ

0.5ꢀ

-

0.5ꢀ

0.35ꢀ

0.25ꢀ

-1

-2

1

2

-4

4

-5

5

-10

-20

-30

-1

10

20

30

1

-5

5

40

-15

-30

-ꢂ0

15

30

ꢂ0

120

240

250

ꢈage

135

150

175

-

270

300

350

10

30

ꢂ0

120

250

415

500

550

15

40

ꢂ0

120

240

250

1400

2200

4200

150

250

0.5ꢀ

0.35ꢀ

0.25ꢀ

001NG

002NG

004NG

005NG

010NG

020NG

030NG

001PG

005PG

015PG

030PG

0ꢂ0PG

100PG

150PG

0

1

2

4

inH₂O

psi

3ꢀ

2ꢀ

1.5ꢀ

1ꢀ

2ꢀ

1.25ꢀ

0.75ꢀ

0.5ꢀ

-

5

10

20

30

1

5

15

30

ꢂ0

100

150

psi

-

250

¹Working pressure: The maximum pressure that may be applied to any port of the sensor in continuous use. This pressure may be outside the operating pressure range limits (Pmin. to

Pmax.) in which case the sensor may not provide a valid output until pressure is returned to within the operating pressure range. Tested to 1 million cycles, minimum.

²Overpressure: The maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the operating pressure range. Exposure

to higher pressures may cause permanent damage to the product. Unless otherwise specified this applies to all available pressure ports at any temperature with the operating

temperature range.

³Burst pressure: The maximum pressure that may be applied to any port of the product without causing escape of pressure media. Product should not be expected to function after

exposure to any pressure beyond the burst pressure.

⁴Common mode pressure: The maximum pressure that can be applied simultaneously to both ports of a differential pressure sensor without causing changes in specified

performance.

⁵Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure range. Includes all errors due to offset, full scale

span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span, and thermal hysteresis

^ꢂTotal Error Band after Auto-Zero: The maximum deviation from the ideal transfer function over the entire compensated pressure range at a constant temperature and supply voltage

for a minimum of 24 hours after an auto-zero operation. Includes all errors due to full scale span, pressure non-linearity, pressure hysteresis, and thermal effect on span.

sensing.honeywell.com

16

Available Standard Conﬁgurations

figure 5. All Aꢊailable Standard Conꢋigurations (Dimensional draꢍings on pages noted beloꢍ.)

Pressure Port

Pacꢌage

Code

DꢂP

SMꢄ

SꢂP

NN

AA

AN

LN

FF

page 19

page 21

page 24

page 25

—

page 19

page 22

—

page 25

page 26

FN

GN

NB

RN

page 26

page 27

page 20

page 22

sensing.honeywell.com

17

Available Standard Conﬁgurations

figure 5. All Aꢊailable Standard Conꢋigurations (Continued; dimensional draꢍings on pages noted beloꢍ.)

Pressure Port

Pacꢌage

Code

DꢂP

SMꢄ

SꢂP

RR

DR

JN

page 20

page 21

page 23

page 27

page 28

page 29

page 23

page 24

—

JJ

HH

HN

MN

SN

—

page 29

sensing.honeywell.com

18

Dimensional Drawings

DIP Packages

figure 6. DꢂP Pacꢌage Dimensional Draꢍings (for reꢋerence only: mm [in].)

Dimensions

DꢂP ꢆꢆ: No ports

0,25

10,0

5,44

[0.010]

[0.39]

[0.214]

8

7

6

5

13,3

6,99

[0.53]

PORT 1

PORT 2

[0.275]

PIN 1

INDICATOR

1

2

3

4

9,24

[0.364]

2,54 TYP.

[0.100]

10,85

[0.427]

8X 0,46

[0.018]

DIP AN: SIngle axial barbed

port

13,75

0,25

[0.010]

[0.541]

10,0

[0.39]

8

7

6

5

7,95

[0.313]

6,2

[0.24]

13,3

[0.53]

6,99

4,93

PORT 2

[0.275]

[0.194]

PIN 1

INDICATOR

PORT 1

1

2

3

4

9,24

[0.364]

11,21

[0.441]

2,54 TYP.

[0.100]

8X 0,46

[0.018]

DꢂP ꢇꢆ: Single axial barbless

port

13,75

0,25

[0.010]

[0.541]

10,0

[0.39]

5,80

[0.228]

8

7

6

5

13,3

6,99

[0.275 ]

PORT 2

[0.53]

PORT 1

PIN 1

INDICATOR

2,47

[0.097]

1

2

3

4

9,24

[0.364]

11,21

[0.441]

2, 54 TYP.

[0.100]

6,95

[0.274]

1,00

[0.039]

8X 0,46

[0.018]

sensing.honeywell.com

19

Dimensional Drawings

DIP Packages

figure 6. DꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

DIP RN: Single radial barbed

port

0,25

[0.010]

10,0

5,80

[0.39]

[0.228]

8

7

6

5

4,2

13,3

[0.17]

[0.53]

6,99

PORT 1

PORT 2

[0.275]

1,93

[0.076]

1

2

3

4

9,24

[0.364]

2,54 TYP.

[0.100]

11,21

[0.441]

8X 0,46

[0.018]

DꢂP ꢀꢀ: Dual radial barbed

ports, same side

0,25

10,0

6,16

[0.242]

[0.010]

[0.39]

4,0

8

7

6

5

[0.16]

2X 1,93

[0.076]

13,3

[0.53]

PORT 1

6,99

PORT 1

PORT 2

[0.275]

PORT 2

4,65

[0.183]

1

2

3

4

9,24

[0.364]

2,54 TYP.

[0.100]

11,21

[0.441]

3,78

[0.149]

8X 0,46

[0.018]

DIP DR: Dual radial barbed

ports, opposite sides

0,25

15,76

6,16

[0.010]

10,0

[0.620]

[0.242]

[0.39]

2X 1,93

[0.076]

8

7

6

5

13,3

[0.53]

6,99

[0.275]

PORT 1

PORT 2

PORT 1

9,24

1

2

3

4

[0.364]

2,54 TYP.

[0.100]

11,21

[0.441]

3,78

[0.149]

8X 0,46

[0.018]

sensing.honeywell.com

20

Dimensional Drawings

DIP and SMT Packages

figure 6. DꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

DꢂP Jꢆ: Single radial barbless

port

9,91

7,58

[0.298]

[0.390]

6,75

1,9

[0.07]

9,40

[0.370]

3,28

[0.129]

[0.266]

[0.129]

8

7

6

5

2,34

[0.092]

4,1

[0.16]

PORT 1

13,3

[0.53]

7,00

[0.276]

PORT 1

PORT 2

1

2

3

4

9,24

[0.364]

0,25

[0.010]

11,92

[0.469]

6,70

[0.264]

8 X 0,461

[0.018]

DIP JJ: Dual radial radial

barbless ports, same side

9,91

6,51

[0.256]

[0.390]

4,76

[0.187]

2X 6,75

[0.266]

9,40

[0.370]

3,28

[0.129]

2,21

[0.087]

1,9

8

7

6

5

[0.07]

2X 2,34

[0.092]

4,1

[0.16]

PORT 1

13,3

[0.53]

7,00

[0.276]

PORT 1

PORT 2

4,1

[0.16]

4,2

[0.16]

1

2

3

4

9,24

0,25

[0.010]

2,54

[0.364]

[0.100]

11,92

[0.469]

1,94

[0.076]

8 X 0,46

[0.018]

figure 7. SMꢄ Pacꢌage Dimensional Draꢍings (for reꢋerence only: mm [in].)

Dimensions

SMꢄ ꢆꢆ: No ports

10,0

5,44

[0.214]

[0.39]

8

7

6

5

13,3

[0.53]

6,99

[0.275]

PORT 1

PORT 2

PIN 1

INDICATOR

1

2

3

4

4,80

8X 0,46

[0.018]

2,54 TYP.

[0.100]

[0.189]

6,41

[0.252]

sensing.honeywell.com

21

Dimensional Drawings

SMT Packages

figure 7. SMꢄ Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SMꢄ Aꢆ: Single axial barbed port

13,75

[0.541]

10,0

[0.39]

8

7

6

5

7,95

[0.313]

13,3

4,93 DIA.

[0.194]

6,99

[0.53]

2

PORT

[0.275]

PIN 1

INDICATOR

PORT 1

1

2

3

4

4,80

8X 0,46

[0.018]

[0.189]

2,54 TYP.

[0.100]

6,77

[0.266]

SMꢄ ꢇꢆ: Single axial barbless port

13,75

[0.541]

10,0

5,80

[0.394]

[0.228]

8

7

6

5

13,3

[0.53]

6,99

PORT 2

[0.275]

PORT 1

PIN 1

INDICATOR

2,47 DIA.

[0.097]

1

2

3

4

4,80

8X 0,46

[0.018]

2,54 TYP.

[0.100]

[0.189]

6,77

[0.266]

SMꢄ ꢀꢆ: Single radial barbed port

5,80

10,0

[0.228]

[0.39]

8

7

6

5

4,2

13,3

[0.53]

[0.17]

6,99

PORT 1

PORT 2

[0.275]

1,93 DIA.

[0.076]

1

2

3

4

4,80

8X 0,46

[0.018]

2,54 TYP.

[0.100]

[0.189]

6,77

[0.266]

sensing.honeywell.com

22

Dimensional Drawings

SMT Packages

figure 7. SMꢄ Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SMꢄ ꢀꢀ: Dual radial barbed

ports, same side

10,0

6,16

[0.39]

[0.242]

4,0

8

7

6

5

[0.16]

2X 1,93 DIA.

[0.076]

13,3

PORT 1

PORT 2

[0.53]

6,99

PORT 1

PORT 2

[0.275]

4,6

[0.18]

1

2

3

4

4,80

8X 0,46

[0.018]

2,54 TYP.

[0.100]

[0.189]

6,77

[0.266]

3,78

[0.149]

SMT DR: Dual radial barbed

ports, opposite sides

15,8

[0.62]

10,0

6,16

2X 2,93

[0.39]

[0.242]

[0.115]

8

7

6

5

13,3

2X 1,93 DIA.

[0.076]

6,99

[0.53]

[0.275]

PORT 1

PORT 2

1

2

3

4

4,80

8X 0,46

2,54 TYP.

[0.100]

[0.189]

[0.018]

6,77

3,78

[0.149]

[0.266]

SMꢄ Jꢆ: Single radial barbless

port

9,91

6,51

[0.256]

[0.390]

1,87

6,75

3,28

2,21

[0.087]

9,40

[0.370]

[0.074]

[0.266]

[0.129]

8

7

6

3

5

4

2,34

[0.092]

4,15

[0.163]

PORT 1

13,3

[0.53]

PORT 1

6,98

[0.275]

7,00

[0.276]

PORT 2

1

2

8 X 1,28

[0.050]

4,80

[0.189]

8 X 0,461

[0.018]

2,54

[0.100]

7,48

[0.294]

5,38

[0.212]

sensing.honeywell.com

23

Dimensional Drawings

SMT and SIP Packages

figure 7. SMꢄ Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SMT JJ: Dual radial

barbless ports, same side

9,91

[0.390]

7,58

[0.298]

4,76

[0.187]

2X 6,75

[0.266]

9,40

[0.370]

3,28

8

7

6

5

[0.129]

2X 2,34

[0.092]

4,15

[0.163]

PORT 1

PORT 2

6,98

[0.275]

7,00

[0.276]

13,3

[0.53]

4,162

[0.1639]

1

2

3

4

8 X 1,28

[0.050]

5,68

[0.189]

8 X 0,461

[0.018]

2,54

[0.100]

8,36

[0.329]

5,38

[0.212]

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (for reꢋerence only: mm [in].)

Dimensions

SꢂP ꢆꢆ: No ports

10,0

4,87

[0.192]

[0.39]

10,0

PORT 1

PORT 2

[0.39]

15,2

[0.60]

1

2

3

4

0,25

2,54 TYP.

[0.100]

4X 0,51

[0.020]

[0.010]

SIP AA: Dual axial barbed

ports, opposite sides

10,0

[0.39]

22,06

[0.869]

10,0

PORT 2

PORT 1

[0.39]

2X 4.93 DIA.

[0.194]

15,2

[0.60]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

[0.010]

4X 0,51

[0.020]

2,54 TYP.

[0.100]

sensing.honeywell.com

24

Dimensional Drawings

SIP Packages

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SꢂP Aꢆ: Single axial barbed

port

13,75

10,0

[0.541]

[0.39]

10,0

PORT 1

PORT 2

[0.39]

4.93 DIA.

[0.194]

15,2

[0.60]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

2,54 TYP.

[0.100]

[0.010]

4X 0,51

[0.020]

SIP LN: Single axial

barbless port

10,0

13,75

[0.541]

[0.39]

10,0

PORT 2

[0.39]

PORT 1

2,47 DIA.

[0.097]

15,2

[0.60]

1

2

3

4

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

SꢂP ff: Fastener mount,

dual axial barbed ports,

opposite sides

29,48

27,20

[1.071]

[1.161]

23,12

10,44

[0.910]

[0.411]

17,78

[0.700]

PORT 2

PORT 1

2X 3.94 DIA.

[0.155]

2X 4,78 DIA.

[0.188]

20,16

[0.794]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

sensing.honeywell.com

25

Dimensional Drawings

SIP Packages

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SꢂP fꢆ: Fastener mount,

single axial barbed port

29,48

[1.161]

16,38

23,12

[0.645]

[0.910]

17,78

[0.700]

3257ꢁꢂ

3257ꢁꢀ

2X 3.94 DIA.

[0.155]

4.78 DI.A

[0.188]

20,16

[0.794]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

2,54 TYP.

4X 0,51

[0.020]

[0.010]

[0.100]

SꢂP ꢈꢆ: Ribbed fastener

mount, single axial barbed

port

27,96

[1.101]

21,60

16,51

[0.850]

[0.650]

19,06

[0.750]

PORT 2

PORT 1

2X 3,94 DIA.

[0.155]

4.78 DIA.

[0.188]

10,63

[0.418]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢄꢁꢁ

0,25

2,54 TYP.

[0.100]

[0.010]

4X 0,51

[0.020]

SꢂP ꢆB: Fastener mount,

dual axial ports, same side

27,31

[1.075]

25,3

[0.996]

21,60

[0.850]

2X 4,80 DIA.

[0.189]

PORT 2

PORT 1

22,87

[0.900]

2X 3.50 DIA.

[0.138]

13

[0.52]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

[0.010]

4X 0,51

[0.020]

2,54 TYP.

[0.100]

sensing.honeywell.com

26

Dimensional Drawings

SIP Packages

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SIP RN: Single radial barbed

port

10,0

[0.39]

5,80

[0.228]

PORT 1

10,0

[0.39]

PORT 2

1,92 DIA.

[0.076]

15,2

[0.60]

1

2

3

4

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

SIP RR: Dual radial barbed

ports, same side

10,0

[0.39]

6,16

[0.243]

PORT 1

PORT 2

PORT 1

10,0

PORT 2

[0.39]

2X 1,92 DIA.

[0.076]

15,2

[0.60]

1

2

3

4

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

SIP DR: Dual radial barbed

ports, opposite sides

15,8

[0.62]

10,0

[0.39]

6,16

[0.243]

10,0

[0.39]

PORT 2

PORT 1

2X 4.93 DIA.

[0.194]

15,2

[0.60]

1

2

3

4

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

sensing.honeywell.com

27

Dimensional Drawings

SIP Packages

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SIP JN: Single radial barbless

port

10,0

7,58

[0.298]

[0.39]

6,75

[0.266]

1,7

3,28

[0.129]

2,2

[0.087]

9,40

[0.370]

[0.07]

1,9

[0.07]

2,34

[0.092]

PORT 1

7,00

[0.276]

10,0

[0.39]

PORT 2

25,0

[0.98]

15,20

[0.598]

1

2

3

4

1,14

[0.045]

2,1

[0.08]

2,54 TYP.

[0.100]

4 X 0,51

[0.020]

SIP JJ: Dual radial barbless

ports, same side

7,58

[0.298]

4,76

[0.187]

6,75

1,7

[0.07]

[0.266]

3,28

[0.129]

10,0

[0.39]

1,9

[0.07]

2X 2,34

[0.092]

PORT 1

5,8

[0.23]

7,00

[0.276]

10,0

[0.39]

PORT 2

4,2

[0.16]

25,0

[0.98]

15,20

[0.598]

1

2

3

4

1,14

[0.045]

2,1

[0.08]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

29,62

[1.166]

10,58

SIP HH: Fastener mount dual

radial barbed ports, same side

[0.416]

23,12

[0.910]

6,64

[0.261]

PORT 2

PORT 1

PORT 2

PORT 1

28,96

[1.140]

11,27

[0.444]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢄꢁꢁ

0,25

[0.010]

2,54 TYP.

[0.100]

4X 0,51

[0.020]

sensing.honeywell.com

28

Dimensional Drawings

SIP Packages

figure 8. SꢂP Pacꢌage Dimensional Draꢍings (continued)

Dimensions

SIP HN: Fastener mount single

radial barbed port

23,12

[0.910]

7,97

[0.314]

4,78 DIA.

[0.188]

3257ꢁꢀ

28,96

[1.140]

PORT 2

2X 3,94 DIA.

[0.155]

11,27

[0.444]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢃꢁꢁꢁꢄꢁꢁ

0,25

2,54 TYP.

[0.100]

4X 0,51

[0.010]

[0.020]

SIP MN: Manifold mount, outer

diameter seal

5,36

[0.211]

PORT 2

PORT 1

15,24.DIA

[0.600]

12,5

[0.49]

ꢀꢁꢁꢁꢁꢂꢁꢁꢁꢁꢃꢁꢁꢁꢁꢄꢁꢁ

0,25

[0.010]

4X 0,51

[0.020]

2,54 TYP.

[0.100]

SIP SN: Manifold mount, inner

diameter seal

PORT 2

5,1

[0.20]

12,57

PORT 1

[0.495]

13,11

[0.516]

15,6

[0.61]

1

2

3

4

2,54 TYP.

[0.100]

4X 0,51

[0.020]

sensing.honeywell.com

29

Pinouts, PCB Pad Layout

ꢄable 11. Pinouts ꢋor DꢂP and SMꢄ Pacꢌages

ꢁutput ꢄype

I²C

Pin 1

GND

NC

Pin 2

V_supply

Pin 3

SDA

MISO

V_out

Pin 4

SCꢁ

Pin 5

NC

Pin 6

NC

Pin 7

NC

Pin 8

NC

SPI

SCꢁK

GND

SS

NC

Analog

NC

ꢄable 12. Pinouts ꢋor SꢂP Pacꢌages

ꢁutput ꢄype

I²C

Pin 1

GND

NC

Pin 2

V_supply

Pin 3

SDA

V_out

Pin 4

SCꢁ

Analog

GND

figure 9. ꢀecommended PCB Pad ꢇayouts

DꢂP

SMꢄ

SꢂP

1,143

[0.045]

0,813

0,914

[0.036]

[0.032]

13,08

2,032

[0.080]

9,40

[0.515]

[0.370]

2,54

[0.100]

2,54

[0.100]

sensing.honeywell.com

30

TruStability^®Board Mount Pressure Sensors Portfolio Overview

ꢄable 13. ꢄruStability^®Board Mount Pressure Sensors Portꢋolio ꢁꢊerꢊieꢍ

Series

Characteristic

HSC

SSC

ꢄSC

ꢆSC

Pacꢌage:

DIP (Dual In-ꢁine Pin)

SMT (Surface Mount Technology)

SIP (Single In-ꢁine Pin)



ꢁption:

dry gases only, no diagnostics (all pressure ranges)

dry gases only, diagnostics on (all pressure ranges)

liquid media on port 1, no diagnostics ( ꢂ0 mbar to 10 bar | ꢂ kPa to 1 MPa | 1 psi to 150 psi)

liquid media on port 1, diagnostics on ( ꢂ0 mbar to 10 bar | ꢂ kPa to 1 MPa | 1 psi to 150 psi)



—



—

Pressure range:

Absolute:

1 bar to 10 bar | 100 kPa to 1 MPa | 15 psi to 150 psi

Differential:

—



ꢂ0 mbar to 10 bar | ꢂ kPa to 1 MPa | 1 psi to 150 psi

1.ꢂ mbar to 40 mbar | 1ꢂ0 Pa to 4 kPa | 0.5 inH₂O to 30 inH₂O

Gage:



—

ꢂ0 mbar to 10 bar | ꢂ kPa to 1 MPa | 1 psi to 150 psi

2.5 mbar to 40 mbar | 250 Pa to 4 kPa | 1 inH₂O to 30 inH₂O



—

ꢄemperature compensated

Ampliꢋied



—

ꢁutput type:

analog



digital (SPI and I²C)

—

ꢄransꢋer ꢋunction:

10ꢀ to 90ꢀ of Vsupply (analog), 2¹⁴counts (digital)

5ꢀ to 95ꢀ of Vsupply (analog), 2¹⁴counts (digital)

5ꢀ to 85ꢀ of Vsupply (analog), 2¹⁴counts (digital)

4ꢀ to 94ꢀ of Vsupply (analog), 2¹⁴counts (digital)

—



Supply ꢊoltage:

3.3 Vdc

5.0 Vdc

—



1.5 Vdc to 12.0 Vdc (for pressure ranges >ꢂ0 mbar | ꢂ kPa | 1 psi)

2.7 Vdc to ꢂ.5 Vdc (for pressure ranges <40 mbar | 4 kPa | 20 inH₂O)

—



—

Accuracy <0.25 %fSS BfSꢇ



Compensated temperature range:

-20 °C to 85 °C [-4 °F to 185 °F]

0 °C to 85 °C [32 °F to 185 °F]

0 °C to 50 °C [32 °F to 122 °F]

—



—



—



ꢁperating temperature range:

-20 °C to 85 °C [-4 °F to 185 °F]

-40 °C to 85 °C [-40 °F to 185 °F]

—



—



ꢄotal ꢃrror Band:

down to 1ꢀ Full Scale Span max.

down to 2ꢀ Full Scale Span max.

—



—



sensing.honeywell.com

31

ADDꢂꢄꢂꢁꢆAꢇ ꢂꢆfꢁꢀMAꢄꢂꢁꢆ

WARNING

PERSONAL INJURY

The following associated literature is available at sensing.honeywell.com:

• Product line guide

DO NOT USE these products as safety or emergency stop

devices or in any other application where failure of the product

could result in personal injury.

• Product range guide

• Product nomenclature tree

• Installation instructions

Failure to comply with these instructions could result in

death or serious injury.

• Application information

• Technical notes:

- I²C Communications with Honeywell Digital Output

Pressure Sensors

WARNING

MISUSE OF DOCUMENTATION

•

- SPI Communications with Honeywell Digital Output

Pressure Sensors

The information presented in this product sheet is for

reference only. Do not use this document as a product

installation guide.

•

Complete installation, operation, and maintenance

information is provided in the instructions supplied with

each product.

Failure to comply with these instructions could result in

death or serious injury.

wAꢀꢀAꢆꢄꢅ/ꢀꢃMꢃDꢅ

Honeywell warrants goods of its manufacture as being free of

defective materials and faulty workmanship. Honeywell’s standard

product warranty applies unless agreed to otherwise by Honeywell

in writing; please refer to your order acknowledgement or consult

your local sales office for specific warranty details. If warranted

goods are returned to Honeywell during the period of coverage,

Honeywell will repair or replace, at its option, without charge

those items it finds defective. ꢄhe ꢋoregoing is buyer’s sole

remedy and is in lieu oꢋ all other ꢍarranties, eꢉpressed or

implied, including those oꢋ merchantability and ꢋitness ꢋor

a particular purpose. ꢂn no eꢊent shall Honeyꢍell be liable

ꢋor conseꢎuential, special, or indirect damages.

While we provide application assistance personally, through our

literature and the Honeywell website, it is up to the customer to

determine the suitability of the product in the application.

Specifications may change without notice. The information we

supply is believed to be accurate and reliable as of this printing.

However, we assume no responsibility for its use.

sensing.honeywell.com

32

Sales and Service

Honeywell serves its customers through

a worldwide network of sales ofﬁces,

representatives and distributors. For

application assistance, current

speciﬁcations, pricing or name of the

nearest Authorized Distributor, contact

your local sales ofﬁce or email us at

info.sc@honeywell.com. Visit us on

the Web at sensing.honeywell.com

Phone and Fax:

Asia Paciﬁc

+65 6355-2828

+65 6445-3033 Fax

+44 (0) 1698 481481

+44 (0) 1698 481676 Fax

Europe

Latin America +1-305-805-8188

+1-305-883-8257 Fax

USA/Canada +1-800-537-6945

+1-815-235-6847

+1-815-235-6545 Fax

Sensing and Control

Honeywell

1985 Douglas Drive North

Golden Valley, MN 55422

honeywell.com

50099148-A-EN IL50

August 2014


型号：	HSCDAND006BDAA5
厂家：	Honeywell
描述：	BRD MNT PRESSURE SENSORS
文件：	总33页 (文件大小：4655K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

HSCDAND006BDAA5 [HONEYWELL]

相关型号：

HSCDAND010BC2A3

HSCDAND010BC2A5

HSCDAND010BC3A3

HSCDAND010BC3A5

HSCDAND010BC4A3

HSCDAND010BC4A5

HSCDAND010BC5A3

HSCDAND010BC5A5

HSCDAND010BC6A3

HSCDAND010BC6A5

HSCDAND010BC7A3

HSCDAND010BC7A5