FH18-25S-0.3SHW [HRS]
Low Profile 0.3mm Pitch Connectors For FPC; 薄型0.3mm间距连接器对FPC
| 型号： | FH18-25S-0.3SHW |
| 厂家： | 
HRS |
| 描述： | Low Profile 0.3mm Pitch Connectors For FPC |
| 文件： | 总8页 (文件大小：276K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Low Profile 0.3mm Pitch Connectors For FPC
FH18 Series
1.8mm height above
the mounting surface
ꢀFeatures
LIF terminal contacts
1. Low profile 0.3mm pitch FPC connectors
In response to continuous miniturization of products, the demand for
smaller contact spacing on connectors is increasing. Flexible printed
circuits(FPC) with contact pitch of 0.3mm are used with increased
frequency. FH18 series connectors fullfill this requirement. In
addition, these connectors occupy less board space and are lighter
than comparable connectors with contacts spaced at 0.5mm.
FPC
2. Improved Retention of FPC
Non – ZIF Contact
Two types of contacts design are combined in the FH18 connector,
zero insertion force(ZIF) and low insertion force(LIF). Inserted FPC is
held in place by the LIF contact, allowing operator to close down the
actuator and engage the ZIF contacts to assure complete connection.
Retention of FPC
3. Easy to use Flip-Lock Actuator
(
) ZIF mechanism enables good connectivity of
Flip-lock rotating type
FPC by a simple operation and light force. No board space is required
for flip lock operation as compared to slide lock ZIF connectors.
Connection completed
4. Placement on Board
The leads are on two sides of the connector, spaced on 0.6mm and
are visible for solder joint inspection. Flat top surface of the connector
allows board placement with automated equipment.
Actuator closed
ZIF contact
5. Variety of Contact Positions
The connectors are available with 17,21,25,27,39,45 and 51 contacts.
ꢀApplications
Notebook computers, printers, PDAs, digital cameras and other
compact devices for interconnecting the main circuit board with the
LCD, PDP (Plasma Display),HDD or other device.
LIF : Low insertion Force
ZIF : Zero insertion Force
*
*
47
ꢀProduct Specifications
Operating temperature range -40ç to +85ç (Note 1)
Storage temperature range -10ç to +50ç (Note 2)
Current rating 0.15A
Voltage rating 30V AC
Rating
Operating humidity range
Relative humidity 90% max.
(without condensation)
Storage humidity range
Relative humidity 90% max.
(without condensation)
Applicable FPC
Item
t=0.2 0.03 Tin-lead plating (Note 4)
Specification
Conditions
1.Insulation resistance
2.Withstanding voltage
3.Contact resistance
100V DC
50M ohms minimum
90V AC/1 minute
No flashover or insulation breakdown.
100m ohms maximum
1mA
4.
Contact resistance : 100m ohms maximum
No damage, cracks, or parts dislocation.
Durability
10 cycles
(Insertion/withdrawal)
No electrical discontinuity of 1µs or more
Contact resistance: 100m ohms maximum
No damage, cracks, or parts dislocation.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
2 hours in each of the 3 directions.
5.Vibration
No electrical discontinuity of 1µs or more
Contact resistance: 100m ohms maximum
No damage, cracks, or parts dislocation.
2
Acceleration of 490 m/s , 11 ms duration,
6.Shock
sine half-wave waveform, 3 cycles in each of the 3 axis.
Contact resistance: 100m ohms maximum
Insulation resistance: 50M ohms minimum
No damage, cracks, or parts dislocation.
7.Humidity
96 hours at temperature of 40ç and humidity of 90% to 95%
(Steady state)
5 cycles under conditions as follows; Temperature:
-40ç / 15 to 35ç / 85ç / 15 to 35ç,
Time: 30 / 5max. / 30 / 5 max.(minutes)
Contact resistance: 100m ohms maximum.
Insulation resistance: 50M ohms minimum.
No damage, cracks, or parts dislocation.
8.Temperature cycle
9.Resistance to
soldering heat
Reflow: At the recommended temperature profile
Manual soldering: 350 5ç for 3 seconds
No deformation of components affecting performance.
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers nonconducting condition of installed connectors in storage, shipment or during transportation.
Note 3: When FPC is gold plated, the connector contacts should be also gold plated: Select the (05) specification.
ꢀMaterial
Part
Material
Finish
Remarks
UL 94V-0
Color : Beige
Color : Black
Tin-lead plating
Tin-lead plating
Insulator
LCP
————
————
Contact
Phosphor bronze
Bronze
Metal fitting
ꢀOrdering Information
1
2
3
4
5
Series name
FH18
( )
FH18 - 27S - 0.3 SHW 05
Number of contacts 17, 21, 25, 27, 39, 45, 51
Contact pitch
Contact style
0.3mm
1
2
3
4
5
SHW : SMT horizontal mounting type
Plating specifications No symbol : Tin-lead plating
(05) : Gold plating
48
BConnector Operating Instructions, precautions and recommendations
Operation
Precautions
1) Do not apply excessive force or use any type of
tool to operate the actuator.
1.FPC Termination procedure. Connector
installed on the board.
1) Lift up the actuator. Use thumb or index finger.
2) Rotate down the actuator until firmly closed.
It is critical that the inserted FPC is not moved and
remains fully inserted. Should the FPC be moved,
open the actuator and repeat the process, starting
with Step 1 above.
2) The connector will assure reliable performance
when the actuator is open to 130° maximum (see
fig.1) Do not exceed this angle, as this may cause
permanent damage to the connector.
Fig.1
90ç
3) Assure that the FPC/FFC is fully inserted parallel
to mounting surface, with the exposed conductive
traces facing down.
2.FPC Removal
1) Lift up the actuator.
2) Carefully remove the FPC.
FPC conductive traces
49
A
B
)
(
1.7
( 0.15 )
P=0.6
Contact #1
Indicates the number
of contacts
Position indicator
* *
( 0.12 )
( 0.2 )
P=0.6
0.675
(
)
1.4
C
D
1.8(Lead is included)
0
J
0.15 MAX
E : FPC slot dimension*
1
2
Notes ( Indicates the distance from J surface.
1
2
3
The coplanarity of each lead and metal fitting within 0.1.(coplanarity : The distance between the lowest and highest land)
This connector uses LIF(Low Insertion Force) and ZIF(Zero Insertion Force)
contact design. Slight friction will be felt during insertion of FPC in the slot.
Full insertion of FPC is required for secure connection.
Unit: mm
Part Number
CL No.
Number of contacts
A
B
C
D
E
FH18-17S-0.3SHW
FH18-21S-0.3SHW
FH18-25S-0.3SHW
FH18-27S-0.3SHW
FH18-39S-0.3SHW
FH18-45S-0.3SHW
FH18-51S-0.3SHW
586-0684-5
586-0669-1
586-0685-8
586-0658-5
586-0646-6
586-0694-9
586-0671-3
17
21
25
27
39
45
51
07.6
08.8
10.0
10.6
14.2
16.0
17.8
04.2
05.4
06.6
07.2
10.8
12.6
14.4
04.8
06.0
07.2
07.8
11.4
13.2
15.0
06.15
07.35
08.55
09.15
12.75
14.55
16.35
05.4
06.6
07.8
08.4
12.0
13.8
15.6
Note : Embossed tape reel packaging (2,500 pieces/reel).
Order by number of reels.
50
BRecommended Land/ Metal Mask Dimensions
B
0.05
0.6 0.05
0.3 0.05 (Land)
0.25 0.05 (Metal mask)
0.3 0.05
0.5 0.05
0.6 0.05
0.675 0.05
C 0.05
*Recommended metal mask thickness: t=0.15
BRecommended FPC Dimensions
0.05
E
C
0.03
+0.04
_0.03
2
0.4
0.6 0.02
0.3 0.07
0.2
+0.04
_0.03
0.3
(2-0.07)
2-R0.2
0.2 0.03
0.2
(0.1)
0.2 (Conductor width)
0.1 (Conductor gap)
0.6 0.07
0.05
0.6 0.02
0.3 0.02
0.03
B
Note 1 Polyimide and thermal hardening glue are a recommendation for the stiffener.
When drawing a plated lead, 0.3+0.04 is also permitted.
2
-
0.03
Unit: mm
E
Part Number
CL No.
Number of contacts
B
C
FH18-17S-0.3SHW
FH18-21S-0.3SHW
FH18-25S-0.3SHW
FH18-27S-0.3SHW
FH18-39S-0.3SHW
FH18-45S-0.3SHW
FH18-51S-0.3SHW
586-0684-5
586-0669-1
586-0685-8
586-0658-5
586-0646-6
586-0694-9
586-0671-3
17
21
25
27
39
45
51
04.2
05.4
06.6
07.2
10.8
12.6
14.4
04.8
06.0
07.2
07.8
11.4
13.2
15.0
05.4
06.6
07.8
08.4
12.0
13.8
15.6
51
BPackaging Specifications
ꢀEmbossed Carrier Tape Dimensions
(
)
2.3
0.3
4
2
12
(
)
(
)
(
)
0.85
0.85
4.4
Flat surface for placement
with Automatic equipment
2.45
Unreeling direction
Unit: mm
R
Part Number
CL No.
Number of contacts
K
L
M
N
Q
FH18-17S-0.3SHW
FH18-21S-0.3SHW
FH18-25S-0.3SHW
FH18-27S-0.3SHW
FH18-39S-0.3SHW
FH18-45S-0.3SHW
FH18-51S-0.3SHW
586-0684-5
586-0669-1
586-0685-8
586-0658-5
586-0646-6
586-0694-9
586-0671-3
17
21
25
27
39
45
51
16
16
24
24
24
24
24
17.5
17.5
11.5
11.5
11.5
11.5
11.5
07.9
09.1
10.3
10.9
14.5
16.3
18.1
06.6
07.8
09.0
09.6
13.2
15.0
16.8
05.1
06.3
07.5
08.1
11.7
13.5
15.3
16.5
16.5
24.5
24.5
24.5
24.5
24.5
Note:2,500 pieces per reel.
ꢀReel Dimensions
(
)
R
2
Lead portion (400 mm min.)
End portion
Mounting portion
Top cover tape
Blank portion
(10 pockets min.)
Blank portion
(10 pockets min.)
Embossed carrier tape
52
BRecommended Temperature Profile
HRS test conditions
3 seconds or less
240ç
Solder method
:Reflow, IR/hot air
250
200
150
100
50
(Nihon Den-netsu Co., Ltd.’s
Part Number: SENSBY NR-2)
:Room air
200ç
Environment
Solder composition
:Paste, 63%Sn/37%Pb
(Senju Metal Industry, Co., Ltd.’s Part
Number: OZ63-201C-50-9)
160ç
150ç
Test board
:
Glass epoxy 70mm∞70mm∞1.6mm thick
:0.3mm 1.25mm
:0.25mm 1.25mm
Land dimensions
Metal mask
∞
∞
∞0.15mm thick
This temperature profile is based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume/thickness and board
size/thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
(30 seconds)
25ç(60 seconds)
(20-30 seconds)
60-90 seconds
0
Preheating
Time (seconds)
Soldering
180
Start
60
120
53
BFH18 Series Construction (Recommended Specifications)
1. Single-Sided FPC
Material Name
Covering layer film
Cover adhesive
Surface treatment
Copper foil
Material
Thickness (µm)
Polyamide 1 mil
25
25
5
Tin-lead plating
Cu
1oz
35
25
25
30
75
195
Base adhesive
Base film
Polyamide 1 mil
Reinforcement material adhesive
Stiffener
Polyamide 3 mil
Total
2. Using Double-Sided FPC
Material Name
Covering layer film
Cover adhesive
Surface treatment
Through hole copper
Copper foil
Material
Thickness (µm)
Polyamide 1 mil
25
25
5
Tin-lead plating
Cu
15
18
18
25
18
18
25
25
25
25
199
Cu
1/2oz
Base adhesive
Base film
Polyamide 1 mil
Base adhesive
Copper foil
Cu
1/2oz
Cover adhesive
Cover layer film
Reinforcement material adhesive
Stiffener
Polyamide 1 mil
Polyamide 1 mil
Total
Note: Stiffener is not required for the double-sided FPC.
To prevent release of the lock due to FPC bending, please do not use copper foil on the rear side.
3. Precautions
1. This specification is a recommendation for the construction of the FH18 Series FPC (t=0.2 0.03).
2. For details about the construction, please contact the FPC/FFC manufacturers.
FPC/FFC Manufactures' Contact List
Sumitomo Bakelite Co., Ltd. Flexible Printed Circuit Board Division
5-8, Higashi-shinagawa 2-chome, Shinagawa-ku, Tokyo, Japan
TEL:+81 3 5462 4191
FAX:+81 3 5462 4882
Fujikura Ltd. Electronics Global Marketing Department
1-5-1, Kiba, Koto-ku, Tokyo, Japan
TEL:+81 3 5606 1165
FAX:+81 3 5606 1530
NOK Corporation Sales Division Overseas Business Department
1-12-15, Shiba-Daimon, Minato-ku, Tokyo, Japan
TEL:+81 3 3432 6976/8415
FAX:+81 3 3432 3919
54
相关型号：
FH18-25S-0.3SHW(05)
Card Edge Connector, 25 Contact(s), 1 Row(s), Female, Right Angle, 0.024 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-25S-0.3SHW(55)
Card Edge Connector, 25 Contact(s), 1 Row(s), Right Angle, 0.012 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-27S-0.3SHW(05)
Card Edge Connector, 27 Contact(s), 1 Row(s), Female, Right Angle, 0.024 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-27S-0.3SHW(55)
Card Edge Connector, 27 Contact(s), 1 Row(s), Right Angle, 0.012 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-39S-0.3SHW(05)
Card Edge Connector, 39 Contact(s), 1 Row(s), Female, Right Angle, 0.024 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-45S-0.3SHW(05)
Card Edge Connector, 45 Contact(s), 1 Row(s), Female, Right Angle, 0.024 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-51S-0.3SHW(05)
Card Edge Connector, 51 Contact(s), 1 Row(s), Female, Right Angle, 0.024 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
FH18-51S-0.3SHW(55)
Card Edge Connector, 51 Contact(s), 1 Row(s), Right Angle, 0.012 inch Pitch, Surface Mount Terminal, Eject Lever
HRS
©2020 ICPDF网 联系我们和版权申明