FH30-80S-0.3SHW [HRS]
0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors;
| 型号： | FH30-80S-0.3SHW |
| 厂家： | 
HRS |
| 描述： | 0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors |
| 文件： | 总8页 (文件大小：634K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator,
Flexible Printed Circuit ZIF connectors
FH30 Series
Strong actuator construction
Enclosed shaft of the actuator
prevents it from dislocation
Simple FPC insertion
■Features
1. Strong actuator retention
Actuator will not be dislodged when operating under harsh
conditions.
2. Rotating Flip–Lock actuator
Rotating actuator permits easy insertion and retention of the
FPC.
Tactile sensation confirms complete FPC insertion and reliable
mechanical and electrical connection.
3. FPC position hold
Tabs on each side of the FPC assure correct placement and
hold in the connector prior to closing of the actuator.
FPC positioning tab
4. Accepts standard FPC thickness
0.3mm thick standard Flexible Printed Circuit (FPC) can be
used.
Lock
5. Easy solderability on the PC board
The soldering leads are on 0.6 mm or 0.8 mm pitch, exiting on
the front and back of the connector.
6. Board placement with automatic equipment
Flat upper surface and tape and reel packaging facilitate vacuum
pick-up and placement. Standard reel packaging contains 1000
connectors.
7. Conductive traces on the PCB can run under
the connector
No exposed contacts on the bottom of the connector.
8. Halogen-free*
* As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
1
2013.11w
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■Product Specifications
0.3 mm pitch 0.4 mm pitch Operating temperature range -40 to +85°C (Note 2)
Storage temperature range -10 to +50°C (Note 3)
Relative humidity 90% max. Storage humidity range Relative humidity 90% max.
(No condensation)
Ratings Current rating(Note 1)
Voltage rating
0.15 A
0.3 A
Operating humidity range
(No condensation)
30 Vrms AC 50 Vrms AC
Recommended FPC
Item
Thickness: 0.3 0.05, Gold plated contact pads
Specification
Conditions
1. Insulation resistance 500 Mø min.
100 V DC
0.3 mm pitch: 90 Vrms AC / 1 minute
0.4mm pitch: 150 Vrms AC / 1 minute
2. Withstanding voltage No flashover or insulation breakdown
150 mø max.
3. Contact resistance
1 mA AC
20 cycles
* Including FPC conductor resistance
Contact resistance: 150 mø max.
4. Durability
No damage, cracks, or parts dislocation
No electrical discontinuity of 1μs or longer
Contact resistance: 150 mø max.
No damage, cracks, or parts dislocation
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm
10 cycles in each of the 3 directions
5. Vibration
No electrical discontinuity of 1μs or longer
Contact resistance: 150 mø max.
No damage, cracks, or parts dislocation
Acceleration of 981m/s2, 6 ms duration,
sine half-wave, 3 cycles in each of the 3 axis
6. Shock
Contact resistance: 150 mø max.
Insulation resistance: 50Mø min.
No damage, cracks, or parts dislocation
7. Humidity (Steady state)
96 hours at 40°C and humidity of 90 to 95%
Contact resistance: 150 mø max.
Insulation resistance: 50Mø min.
Temperature: -40°C ➝ +15°C to 35°C ➝ +85°C➝ +15°C to 35°C
8. Temperature cycle
Time:
-30
➝
2 to 3
➝ +30 ➝ +2 to 3
No damage, cracks, or parts dislocation 5 cycles
No deformation of components affecting Reflow: At the recommended temperature profile
performance. Manual soldering: 350°C for 5 seconds
9. Resistance to soldering heat
Note1: When passing the current through all of the contacts, use 70% of the rated current.
Note2: Includes temperature rise caused by current flow.
Note3: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of connectors after installation on a
board.
■Materials
Part
Material
LCP
Finish
Remarks
UL94V-0
FH30 series Color:Gray
FH30M series Color:Beige
Gold plated
Insulator
Contacts
Phosphor bronze
--------------
■Ordering information
q
w
e
Series name
: FH
Series No.
Blank
M
: 30
: 0.3mm pitch
: 0.4 mm pitch
( )
FH 30 M - 80S - 0.3 SHW 05
1
2
3
4
5
6
7
r
Number of contacts : FH30 series 60, 80, 90
FH30M series 80, 96
t
y
u
Contact pitch
Contact type
: 0.3 mm, 0.4 mm
SHW(SMT horizontal staggered mounting)
:
Plating specifications : (05)…Gold plated
(98)…Gold plated, 500 pieces/reel
2
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■Dimensions
A
B
C
Q
R
9
(0.12)
Vacuum pick-up surface
R
(0.12)
D
Vacuum pick-up surface
**
0.8
0.8
(E: FPC insertion slot dimension)
Number of contacts indicator
Notes 1: The coplanarity of each terminal lead is within 0.1.
2: Packaged on tape and reel only. Check packaging specification.
3: Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.
4: After reflow, the terminal plating may change color, however this does not represent a quality issue.
All dimensions: mm
Part Number
CL No.
Number of Contacts FPC contact pitch
A
B
C
D
E
Q
R
17.7
23.7
26.7
31.6
38
18.35 0.3
24.35 0.3
27.35 0.3
32.25 0.4
38.65 0.4
FH30-60S-0.3SHW(05)
FH30-80S-0.3SHW(05)
FH30-90S-0.3SHW(05)
FH30M-80S-0.4SHW(05)
FH30M-96S-0.4SHW(05)
580-0105-8-05
580-0100-4-05
580-0106-0-05
580-0102-0-05
580-0103-2-05
60
80
90
80
96
0.3
0.3
0.3
0.4
0.4
21.9
27.9
30.9
35.8
42.2
17.4 17.4
23.4 23.4
26.4 26.4
31.2 31.2
37.6 37.6
0.6
0.6
0.6
0.8
0.8
Tape and reel packaging (1,000 pieces/reel, 500 pieces/reel).
Order by number of reels.
3
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■
Recommended PCB mounting ■Recommended FPC Dimensions
pattern and metal mask dimensions
0.3+0.04
-0.03
0.1 0.05
0.07 0.07
No(n-1)
B
0.05
A
No.1
Q
0.05
C
0.05
0.3 0.03(Land)
R
0.05
0.25 0.03(Metal mask)
No.2
No (n)
0.3 0.05
Q
R
0.02
0.02
2
0.3+0.04
-0.03
Detail A
0.3 0.07
B
F
0.03
0.05
0.1
0.3 0.07
R
0.05
0.3 0.03(Land)
Mark side
0.25 0.03(Metal mask)
G
D
0.05
H
J
MIN
Recommended metal mask thickness: t=0.15
0.1
Note 1
:
Conductor width shall be 0.1 0.05 if FPC has plating bars.
All dimensions: mm
Part Number
CL No.
Number of Contacts FPC contact pitch
B
C
D
F
G
H
J
Q
R
FH30-60S-0.3SHW(05) 580-0105-8-05
FH30-80S-0.3SHW(05) 580-0100-4-05
FH30-90S-0.3SHW(05) 580-0106-0-05
FH30M-80S-0.4SHW(05) 580-0102-0-05
FH30M-96S-0.4SHW(05) 580-0103-2-05
60
80
90
80
96
0.3
0.3
0.3
0.4
0.4
17.7 17.4 17.4 18.3 18.8 19.3 20.3 0.3 0.6
23.7 23.4 23.4 24.3 24.8 25.3 26.3 0.3 0.6
26.7 26.4 26.4 27.3 27.8 28.3 29.3 0.3 0.6
31.6 31.2 31.2 32.2 32.7 33.2 34.2 0.4 0.8
38 37.6 37.6 38.6 39.1 39.6 40.6 0.4 0.8
■FH30 Series Recommended FPC Construction
Material Thickness
(μm)
1. Using Single-sided FPC
Material Name
Material
1 mil thick
Covering film layer
Cover adhesive
Polyimide
(25)
(25)
3
0.2μm thick gold plated over 1 to
5μm thick nickel underplating
Surface treatment
Copper foil
Base adhesive
Base film
Cu
Thermosetting adhesive
Polyimide 1 mil thick
1oz
35
25
25
Reinforcement material adhesive Thermosetting adhesive
30
Stiffener
Polyimide
Total
7 mil thick
175
293
Material Thickness
(μm)
2. Using Double-sided FPC
Material Name
Material
1 mil thick
Covering layer film
Cover adhesive
(25)
(25)
3
Polyimide
0.2μm thick gold plated over 1 to
5μm thick nickel underplating
Surface treatment
Through-hole copper
Copper foil
Cu
15
18
Cu
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
Cu 1/2oz
Thermosetting adhesive
Polyimide 1 mil thick
1/2oz
Base adhesive
Base film
18
25
Base adhesive
Copper foil
18
(18)
25
Cover adhesive
Covering film layer
25
50
Reinforcement material adhesive Thermosetting adhesive
100
Stiffener
Polyimide
Total
4 mil thick
297
* To prevent release of the FPC due to it’s bending, use of the double-sided FPC with copper foil on the back side is NOT RECOMMENDED.
3. Precautions
1. This specification is a recommendation for the construction of the FH30 Series FPC (t=0.3 0.05).
2. For details about the construction, please contact the FPC manufacturers.
4
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■Packaging Specifications
●Embossed Carrier Tape Dimensions
●Reel Dimensions
2
0.15
(4.9)
4
0.1
12 0.1
0.4 0.1
(T: INSIDE)
(U: OUTSIDE)
End section
Mounting section
Lead section (400mm min.)
1.5+0.1
0
1.35 0.1
(6.8)
Top cover tape
Embossed carrier tape
No connector inserted
(10 pockets min.)
No connector inserted
(10 pockets min.)
Unreeling direction
All dimensions: mm
L
Part Number
CL No.
Number of Contacts
K
M
N
T
U
FH30-60S-0.3SHW(05)
FH30-80S-0.3SHW(05)
FH30-90S-0.3SHW(05)
FH30M-80S-0.4SHW(05)
FH30M-96S-0.4SHW(05)
60
80
90
80
96
44
44
44
56
56
40.4
40.4
40.4
52.4
52.4
20.2
20.2
20.2
26.2
26.2
22.1
28.1
31.1
36
45.4
45.4
45.4
57.4
57.4
49.4
49.4
49.4
61.4
61.4
580-0105-8-05
580-0100-4-05
580-0106-0-05
580-0102-0-05
580-0103-2-05
42.4
Tape and reel packaging (1,000 pieces/reel).
■Temperature Profile
● Using Lead-free Solder Paste
HRS test condition
Solder method
Environment
MAX 250ç
:Reflow, IR/hot air
:Room air
250
230ç
Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part
200
150
100
50
200ç
Number:M705-221CM5-32-10.5)
Test board
:Glass epoxy FH30:45∞80∞1.6mm thick
FH30M:70∞130∞1.6mm
thick
150ç
Land dimensions
Metal mask
:0.3mm∞1.7mm
:0.15mm thick
0.25mm∞1.7mm
25ç
(60 sec.)
90 to 120 sec.
Preheating
(30 sec.)
Soldering
The temperature profiles shown are based on the above
conditions.
0
Start
In individual applications the actual temperature may
vary,depending on solder paste type, volume / thickness and
board size / thickness. Consult your solder paste and
equipment manufacturer for specific recommendations.
Time (Seconds)
5
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■Operation and Precautions
Operation and Precautions
q Install on the PC board with the actuator open.
e Actuator closing after the FPC is fully inserted.
Rotate the actuator down to a full stop, pushing it at
the center.
w FPC Insertion
Orient the FPC with the contact pads facing down.
Insert in the connector at an angle, assuring that the
positioning tabs are placed in the corresponding
positioning tab areas on both sides of the insulator
body.
Lower the FPC to a position parallel to the mounting
surface.
Verify the correct position by slightly pulling
horizontally on the FPC.
Positioning tab area (each side)
r Removing the FPC
Carefully rotate the actuator up, lifting it at the center.
Lift the FPC slightly to clear the positioning tabs and
withdraw it from the connector.
Positioning part
6
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
■Precautions
Operation and Precautions
q Actuator operation
w FPC Insertion and closing of the actuator.
Do not insert the FPC on an angle as illustrated in the
photograph below.
The actuator rotates at the center of it’s shaft, as
illustrated in the figure below.
Rotation shaft
Be careful not to apply excessive force when
operating the actuator from the open position (before
the FPC has been inserted).
Exercise care not to touch the contacts with
fingernails or any other object.
Properly insert the FPC positioning tabs into the
corresponding areas on both sides of the insulator
body.
Incorrect FPC insertion
Correct FPC insertion
During the closing of the actuator do not pull up or
push on it directly down.
e Make sure that the FPC does not rub against the
insertion slot or the contacts, as illustrated on the
figure below.
Do not grasp the actuator and pull on it (photograph
below).
7
FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
Operation and Precautions
Closing of the actuator.
r Opening of the actuator
Rotate down pushing it at the center or evenly at
each end, as shown on the photographs below. Do
not push at one end only.
Rotate up, lifting it at the center or evenly at each end
of the actuator.
Do not lift at one end only.
t Forces to the FPC after insertion and closing of
the actuator.
Do not apply upward pull-force to the FPC close to the
connector.
If a need arise to route the FPC upward, assure that
it is NOT transferring any forces to the closed
actuator.
8
相关型号：
FH30-80S-0.3SHW(05)
Card Edge Connector, 80 Contact(s), 1 Row(s), Female, Right Angle, Surface Mount Terminal, Locking, ROHS COMPLIANT
HRS
FH30-80S-0.3SHW(98)
Card Edge Connector, 80 Contact(s), 1 Row(s), Right Angle, 0.012 inch Pitch, Surface Mount Terminal, Locking, Gray Insulator
HRS
FH30-90S-0.3SHW
0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
HRS
FH30M-80S-0.4SHW
0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
HRS
FH30M-80S-0.4SHW(05)
Card Edge Connector, 80 Contact(s), 1 Row(s), Female, Right Angle, 0.016 inch Pitch, Surface Mount Terminal, Locking, Beige Insulator, ROHS COMPLIANT
HRS
FH30M-80S-0.4SHW(98)
Card Edge Connector, 80 Contact(s), 1 Row(s), Right Angle, 0.016 inch Pitch, Surface Mount Terminal, Locking, Beige Insulator
HRS
FH30M-96S-0.4SHW
0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
HRS
FH30M-96S-0.4SHW(05)
Card Edge Connector, 96 Contact(s), 1 Row(s), Right Angle, 0.016 inch Pitch, Surface Mount Terminal, Locking, Beige Insulator
HRS
©2020 ICPDF网 联系我们和版权申明