HR30-6RA-10PD [HRS]
Miniature Waterproof Plastic Connectors; 微型防水塑料连接器型号: | HR30-6RA-10PD |
厂家: | HRS |
描述: | Miniature Waterproof Plastic Connectors |
文件: | 总12页 (文件大小:867K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NEW
Miniature Waterproof Plastic Connectors
HR30 Series
Mated dimensions
32.3
3 and 6 pos.
42.1
10 and 12 pos.
ꢀFeatures
Lock/release operation
1. Small size
Short in length when fully terminated and mated.
Push-pull- single action lock
2. Water and dust protected
IP67 protection rating: Complete protection against dust
penetration and against water penetration when
submerged 1 meter deep for half hour. Mated with
corresponding connector or protective cap.
3. Simple pull lock release
Built-in lock/release mechanism securely locks mated
connectors while allowing quick disconnection by simply
pulling on the plug’s release collar. Molded-in grooves
prevent hand slippage when pulled.
Alignment marks
The round configuration of the collar allows easy side-by-
side panel mounting and will not snag on objects when
the cable is pulled-out.
Push-pull locking collar
4. Light weight, corrosion resistant
Glass reinforced thermoplastic compounds and non-
corrosive components are used in all assemblies.
5. Contact protection and self- alignment
Multiple polarizing keys protect the contacts from miss-
alignment or attempted insertion of the wrong connector,
while assuring correct mating between the corresponding
connectors.
6. Visual alignment indicators
Permanent alignment indicators in a contrasting color on
all connectors aid in correct alignment and engagement.
Polarized interface
7. Built-in cable strain relief
ꢀApplications
Test and measuring equipment, portable devices,
instrumentation, industrial devices, recreational equipment,
I/O applications and other applications requiring use of
lightweight, corrosion resistant quick mate/ release cable
connections.
2004.6
1
ꢀProduct Specifications
5A (3 pos.)
2A (6,10,12 pos.)
Current rating
Ratings
Operation Temperature Range
StorageTemperature Range
+
-25ç to 85ç
100V AC,140V DC(3,6 pos.)
30V AC,42V DC(10,12 pos.)
Voltage rating
+
-25ç to 85ç
Characteristic
Specification
Conditions
5m ohms max. (3 pos.)
15m ohms max. (Solder type: 6, 10, and 12 pos.)
30m ohms max. (Through hole type: 6 and 12 pos.)
1.Contact resistance
1A DC
1000M ohms min.
2.Insulation resistance
3.Withstanding voltage
100 V DC
No flashover or insulation breakdown
300 V AC / one minute
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
2 hours in each of the 3 directions
4.Vibration
No electrical discontinuity of 10 µs or more
Contact resistance 10m ohms min.(3 pos.)
Contact resistance 30m ohms min. (Solder type: 6, 10, and 12 pos.)
Contact resistance 100m ohms min. (Through hole type: 6 and 12 pos.)
5.Durability (mating/un-mating)
6.Temperature cycle
7.Humidity resistance
1000 cycles
ꢀ
ꢀ
(-55ç: 30 minutes Room temperature: 10 to 15 minutes +85ç: 30
Insulation resistance 100 M ohms min.
ꢀ
minutes Room temperature: 10 to 15 minutes) for 5 cycles
Insulation resistance
10M ohms min. (when humidity high)
100M ohms min. (when dry)
96 hours at temperature of 40ohmsC and humidity of 90% to 95%
8.Waterproof performance
9.Dust protection
While mated with corresponding or protective cap submerged at
depth of 1m for half hour.
No penetration inside.
ꢀMaterial
Assembly
Component
Insulator
Material
Finish
Remarks
UL94V-0
UL94V-0
----------
PPS
Black
PBT
Black
Polyacetal
Natural
Plug
Gasket
Silicone rubber, chloroprene rubber
Brass, phosphor bronze
Stainless steel
Red/Black
----------
Contacts
Spring
Gold plated
----------
----------
----------
Insulator
Gasket
PPS
Black
UL94V-0
----------
Chloroprene rubber
Brass, phosphor bronze
Zinc alloy
Black
Receptacles
Contacts
Hexagonal nut
Washer
Gold plated
Chromate
Nickel plated
----------
----------
Phosphor bronze
----------
Crimp contact
(male/female)
Contacts
Phosphor bronze
Selective gold plated
----------
ꢀOrdering information
HR 3 0 - 6 P A - 6 S C
1
2
3
4
5
6
7
Number of Contacts : 3, 6, 10 and 12
5
1
2
Series name
Shell size
: HR30
Outside diameter/plug mating side
:
6 Contact type
S
P
: Female contact
: Male contact
Connector type : P : Plug
Connector type : R : Receptacle
Connector type : J : Jack
3
7
Contact wiring type
Blank : Solder
C
D
: Crimping
: Through hole
4 Variation
Blank : Standard
: Fine wire
A
2
ꢀPlugs
ꢀSolder Type
HR30-6P-6S (Shown)
A(Fully tightened)
Applicable
cable diameter
1
6
5
2
4
3
Part Number
CL No.
A
B
Solder pot inner diameter Applicable cable diameter range
1.1 mm
Weight
HR30-6P-3S
HR30-6P-6S
HR30-6P-6P
HR30-6PA-3S
HR30-6PA-6S
HR30-6PA-6P
HR30-7P-12S
HR30-8P-12P
130-0004-1
130-0010-4
130-0009-5
130-0021-0
130-0019-9
130-0020-8
130-0027-7
130-0026-4
29.8
30.3
29.8
30.3
4.2 to 5
0.8 mm
4g
12.6
1.1 mm
3.5 to 4.3
0.8 mm
6.7g
6.2 to 7
39.8
15.5
0.6 mm
ꢀCrimp Type
HR30-7P-12SC (Shown)
Applicable
A(Fully tightened)
cable diameter
Shown with terminated and installed contacts.
Part Number
CL No.
A
Crimp contact
Applicable cable diameter range
Weight
6g
HR30-7P-10SC
HR30-7P-12SC
HR30-8P-12PC
130-0013-2
130-0014-5
130-0015-8
HR30-SC-211
6.2 to 7
39.8
HR30-PC-211
Note: Crimp contacts are not included. Please order applicable contacts separately.
3
ꢀReceptacles
ꢀSolder Type
A
HR30-6R-6P (Shown)
Gasket
B
1
6
2
5
4
3
E(Thread)
F(Hex nut)
Lock washer
Part Number
HR30-6R-3P
HR30-6R-6P
HR30-6R-6S
HR30-7R-12P
HR30-8R-12S
CL No.
Solder pot inner diameter Weight
A
B
C
D
E
F
130-1003-4
130-1009-0
130-1008-8
130-1016-6
130-1018-1
1.1mm
16
∞
8.3
12
8.9
M8 0.75
10
2g
0.8mm
18.4
18.6
∞
9.3
15
11.5
M11 1
13
3.4g
0.6mm
ꢀCrimp Type
15.5
HR30-7R-12PC (Shown)
9.3
Gasket
M11X1(Thread)
SShhoowwnnwwiitthhtteerrmmiinnaatteeddaannddiinnssttaallleeddccoonnttaaccttss..
13(Hex nut)
Lock washer
Part Number
CL No.
Crimp contact
HR30-PC-211
Weight
3g
HR30-7R-10PC
HR30-7R-12PC
HR30-8R-12SC
130-1012-5
130-1013-8
130-1014-0
HR30-SC-211
ꢀThrough hole Type
HR30-8R-12SD (Shown)
A
B
2
Through hole post
(0.2∞0.5)
E
F(Hex nut)
Lock washer
Gasket
Part Number
HR30-6R-6PD
HR30-6R-6SD
HR30-7R-12PD
HR30-8R-12SD
CL No.
Weight
A
B
C
D
E
F
130-1020-3
130-1021-6
130-1017-9
130-1019-4
14.9
15.2
∞
8.3
12
8.9
M8 0.75
10
2g
∞
16
9.3
15
11.5
M11 1
13
3.4g
4
ꢀJacks
ꢀSolder Type
HR30-6J-6P (Shown)
Applicable
cable diameter
B(Fully tightened)
1
6
2
5
3
4
Part Number
CL No.
A
B
Applicable cable diameter range Solder pot inner diameter
Weight
3g
HR30-6J-6P
HR30-6JA-6P
HR30-7J-12P
HR30-8J-12S
130-2009-6
130-2018-7
130-2020-9
130-2019-0
4.2 to 5
12
28.9
0.8 mm
3.5 to 4.3
5.7g
5.9g
15
37.3
0.6 mm
6.2 to 7
ꢀCrimp Type
HR30-7J-12PC (Shown)
37.3(Fully tightened)
Applicable
cable diameter
Shown with terminated and installed contacts.
Part Number
HR30-7J-10PC
HR30-7J-12PC
HR30-8J-12SC
CL No.
Crimp contact
HR30-PC-211
Applicable cable diameter range
Weight
5g
130-2015-9
130-2017-4
130-2016-1
6.2 to 7
HR30-SC-211
Note: Crimp contacts are not included. Please order applicable contacts separately.
5
ꢀCaps
ꢀFor Plugs
HR30-6P-C
Ø
E
Part Number
HR30-6P-C
CL No.
Applicable connector
A
B
C
D
4
E
Weight
1g
HR30-6P-3S
HR30-6P-6S
HR30-6P-6P
13
8.4
8.9
8.8
130-3000-7
HR30-6PA-3S
HR30-6PA-6S
HR30-6PA-6P
HR30-7P-10SC
HR30-7P-12S
HR30-7P-12SC
HR30-8P-12P
HR30-8P-12PC
HR30-7P-C
HR30-8P-C
130-3004-8
130-3003-5
16
10.4
10.5
6
11.4
2g
ꢀFor Receptacle
HR30-6R-C
Ø
E
Ø
D
Part Number
HR30-6R-C
CL No.
Applicable connector
A
B
C
D
E
Weight
HR30-6R-3P
HR30-6R-6P
130-3001-0
HR30-6R-6PD
HR30-6R-6S
12.6
11.8
7.5
12.1
9.1
HR30-6R-6SD
HR30-7R-10PC
HR30-7R-12P
HR30-7R-12PC
HR30-7R-12PD
HR30-8R-12S
HR30-8R-12SC
HR30-8R-12SD
1g
HR30-7R-C
130-3002-2
15.5
14.8
8.5
15
12.1
Note : When using these caps, do not use the gasket that is normally supplied with the receptacle. The “B” diameter end of the
receptacle cap will serve as the gasket.
6
ꢀCrimp Contacts
Male contact
Female contact
1.2
1.2
A
A
A
A
11
A-A cross-section
11
A-A cross-section
Part Number
CL No.
Packaging type
100pcs/bag
Weight
Part Number
CL No.
Packaging type
100pcs/bag
Weight
HR30-PC-111 130-0022-3
0.03g/1per pin
HR30-SC-111 130-0023-6
0.03g/1 pin
0.03g/1 pin
HR30-PC-211 130-0016-0 10,000pcs/reel 0.03g/1per pin
HR30-SC-211 130-0017-3 10,000pcs/reel
Note : Use wire size AWG 26 to 30 with a jacket diameter of 1 mm max.
BConnecting Combinations
Plugs
Receptacles
HR30- R-
*
**
HR30- P-
*
**
Jacks
*
**
HR30- J-
Caps for Receptacle
Caps for Plug
*
HR30- R-C
*
HR30- P-C
Panel
(Shown for reference only.)
Cable
(Shown for reference only.)
Cap
Cap
Note 1 : When selecting connectors, take into account the shell size, contact count and gender of the contacts.
Note 2 : When using the protective caps for the receptacles, do not use the gaskets normally supplied with the receptacle. Protective caps must
be fully inserted to assure specified IP67 water and dust protection.
7
BApplicable Fixtures
ꢀSolder termination fixture
Part Number
CL No.
Applicable Connectors
HR30-6P-3S
HR30-6P-3S-T01
HR30-6P-6S-T01
150-0220-1
HR30-6PA-3S
HR30-6P-6S
150-0214-9
HR30-6PA-6S
HR30-6P-6P
HR30-6P-6P-T01
150-0221-4
150-0228-3
150-0223-0
HR30-6PA-6P
HR30-7P-10SC
HR30-7P-12S
HR30-7P-12SC
HR30-8P-12P
HR30-8P-12PC
HR30-6R-3P
HR30-7P-10SC-T01
HR30-7P-12SC-T01
HR30-8P-12PC-T01
HR30-6R-3P-T01
150-0227-0
150-0225-5
HR30-6R-6P
HR30-6R-6P-T01
150-0218-0
HR30-6J-6P
HR30-6JA-6P
HR30-6R-6S
HR30-6R-6S-T01
150-0222-7
150-0231-8
150-0230-5
150-0226-8
HR30-7J-10PC-T01
HR30-7J-12PC-T01
HR30-8J-12SC-T01
HR30-7J-10PC
HR30-7J-12PC
HR30-8J-12SC
Note : The back shell tightening collar is used to tighten the back shell to the specified torque.
Refer to assembly procedures.
ꢀTightening collar for back shell
Part Number
HR30-6P-T02
HR30-8P-T02
CL No.
Applicable Connectors
3 and 6 pos.
150-0216-4
150-0224-2
10 and 12 pos.
Note: The back shell tightening collar is used to tighten the back shell to specified torque.
Refer to assembly procedures.
Solder termination fixture
Back shell tightening collar
HR30-6P-6S-T01
HR30-6R-6P-T01
HR30-6P-T02
8
ꢀApplicable Tools
Type
Description
Part Number
HT-102/HR30-1
CM-105
CL No.
Applicable contact
HR30-SC-111
HR30-PC-111
----------
Applicable wire
Manual
Manual crimping tool
Automatic crimping machine
Applicator
150-0229-6
901-0005-4
901-2015-9
AWG#26~#30
----------
Automatic
HR30-SC-211
HR30-PC-211
HR30-SC-111
HR30-SC-211
HR30-PC-111
HR30-PC-211
AP105-HR30-1
AWG#26~#30
----------
Extraction tool
HR30-TP
150-0219-2
----------
Manual contact crimping tool HT-102/HR30-1
Automatic contact crimping machine CM-105
Contact extraction tool HR30-TP
BReceptacle, Board Mounting Through Hole Pattern
2.16
1.44
2.16
1.44
2.16
1.44
2.16
1.44
0.9
0.9
0.9
0.9
6-Ø0.65
6-Ø0.65
12-Ø0.65
12-Ø0.65
6
1
3
1
1
3
1
5
2
6
7
4
4
7
5
4
2
10
12
8
8
10
12
3
4
3
11
11
0.9
0.9
0.72
0.72
0.72
0.72
1.81.8
1.52 1.52
6R-6PD
6R-6SD
7R-12PD
8R-12SD
Notes 1.The receptacle through hole configuration depicts a view from the mating side of the connector.
2.The recommended board maximum thickness :1.2 mm.
3.Tolerance of +0.03 mm is recommended for the plated through hole location.
Tolerance of +0.02 mm is recommended for the plated through hole diameter.
BContact Position Arrangement
BPanel Cutout
Alignment mark
A+0.05
Alignment mark
0
1
3
6
4
5
1
1
3
6
3
2
5
4
2
2
HR30-6P-3S
HR30-6P-6S
HR30-6P-6P
3
2
9
1
8
1
8
2
9
3
3
2
9
1
8
7
6
5
4
4
5
6
7
7
6
5
4
10
10
A
B
C
D
Panel Thishness
0.7~2
10
11
12
11 12
3,6 pos
1.25
6.45
9.25
8.05
11.05
3.95
5.45
HR30-7P-10SC
HR30-7P-12SC
HR30-8P-12PC
10,12 pos 1.35
0.7~3
Notes 1.The contact configuration depicts a view from the wiring side.
2. Mounting to the panel is accomplished by tightening the hexagonal nut from the rear side of the panel.
9
BAssembly Procedures
Plug Assembly Sequence
Push/pull locking collar
Seal bushing
Strain relief
Insulator/contact assembly
Back shell
Spring
1
A
B
Cable
A
B
2 mm
Solder type : 3 and 6 pos.
Solder type : 12 pos.
5.5 mm max.
10 mm max.
15 to 20 mm
2 mm
-0
-0.5
2
mm
Crimp type : 10 and 12 pos.
Thread the back shell, strain relief, seal bushing, spring and push/pull locking collar over the cable as shown above.
Block end face
Insulator/contact assembly
Solder termination fixture
2
Solder type
1. Pre-solder the exposed cable conductors (dia. A). The diameter of the pre-soldered conductors should not exceed 0.7
mm for 6 contact plug and 1.0 mm for 3 contact plug.
2. Insert the insulator body over the applicable solder termination fixture.
3. Insert the pre-soldered conductors in the contact soldering pot and solder them in place.
Soldering iron temperature should be 280 10ç applied for 3-4 second.
Crimp type
1. Crimp the applicable contact to the stripped conductor. Use correct crimp tools. Verify the dimensions and crimp
configuration.
2. Insert the contact into the appropriate opening in the insulator body.
3. Verify fully seated position by applying a slight pull force on the conductor. The contact should remain in place.
Re-insert if not seated.
10
Cable
Back shell
Cable
Push/pull
locking collar
Guide keys
Tightening collar for back shell
A
Plug insulator body
Solder termination fixture
Cable
View A (2:1)
3
Groove - sealing bushing
Front edge of cable jacket
Figure B
Figure C
Back shell tightening collar size Torque
Connector
.
3 and 6 Pos.
16 mm
18 mm
0.5N m
.
10 and 12 Pos.
0.5N m
1. To prevent accidental loosening of the back shell it is recommended that a small amount of primer (Loctite® 7649) and
adhesive (Loctite® 271) be applied to the threads of the insulator body before proceeding.
2. Keeping the terminated insulator body on the fixture, re-assembly the plug in order shown.
4. Using the correct back-tightening collar tighten the back shell to the specified torque.
When tightening the collar make sure that the cable will NOT turn.
5. Remove the assembly from the fixture.
Note: Loctite is a registered trademark of the Henkel Loctite Corporation.
11
BGeneral usage notes
1. Mating
2. Un-mating
Mounting panel
Receptacle
Cable
D
Plug
Push/pull locking collar
C
Cable
A
D
Alignment marks
B
C
When mounting, smooth mating will be achieved by holding plug
in any are “A” and aligning the arrow of the plug with that of the
receptacle ,then pushing the plug straight in.
When removing the plug from its connected condition, hold the
plug by push/pull locking collar (area “B”) and pull straight off.
BPrecautions
1. Do NOT apply force in excess of 30N in the directions shown below.
30 N max.
30 N max.
Panel
30 N max.
2. To maintain the water/dust protection performance and the cable clamp force, use a cable that is within the range of applicable cable diameter.
3. Consult HRS representative when using different cables.
®
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
http://www.hirose-connectors.com
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
12
相关型号:
©2020 ICPDF网 联系我们和版权申明