H5DU2562GTR-K2 [HYNIX]
DDR DRAM, 16MX16, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66;型号: | H5DU2562GTR-K2 |
厂家: | HYNIX SEMICONDUCTOR |
描述: | DDR DRAM, 16MX16, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66 动态存储器 双倍数据速率 光电二极管 |
文件: | 总28页 (文件大小:376K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
256Mb DDR SDRAM
H5DU2562GTR-xxI
H5DU2582GTR-xxI
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 1.0 / Jul. 2009
1
H5DU2562GTR-xxI
H5DU2582GTR-xxI
Revision History
Revision No.
History
Draft Date Remark
0.1
0.2
1.0
Preliminary
Revised tRC, tWR spec @ DDR500
Release
Jun. 2009
Jun. 2009
Jul. 2009
Rev. 1.0 / Jul. 2009
2
H5DU2562GTR-xxI
H5DU2582GTR-xxI
DESCRIPTION
The H5DU2582GTR and H5DU2562GTR are a 268,435,456-bit CMOS Double Data Rate(DDR) Synchronous DRAM, ide-
ally suited for the main memory applications which requires large memory density and high bandwidth.
This Hynix 256Mb DDR SDRAMs offer fully synchronous operations referenced to both rising and falling edges of the
clock. While all addresses and control inputs are latched on the rising edges of the CK (falling edges of the /CK), Data,
Data strobes and Write data masks inputs are sampled on both rising and falling edges of it. The data paths are inter-
nally pipelined and 2-bit prefetched to achieve very high bandwidth. All input and output voltage levels are compatible
with SSTL_2.
FEATURES
•
•
VDD, VDDQ = 2.5V +/- 0.2V
•
All addresses and control inputs except data, data
strobes and data masks latched on the rising edges
of the clock
All inputs and outputs are compatible with SSTL_2
interface
•
•
•
Programmable CAS latency 2/2.5 (DDR200, 266,
333), 3 (DDR400) and 4 (DDR500) supported
•
•
•
Fully differential clock inputs (CK, /CK) operation
Double data rate interface
Programmable burst length 2/4/8 with both sequen-
tial and interleave mode
Source synchronous - data transaction aligned to
bidirectional data strobe (DQS)
Internal four bank operations with single pulsed
/RAS
•
•
x16 device has two bytewide data strobes (UDQS,
LDQS) per each x8 I/O
•
•
•
•
Auto refresh and self refresh supported
tRAS lock out function supported
8192 refresh cycles/64ms
Data outputs on DQS edges when read (edged DQ)
Data inputs on DQS centers when write (centered
DQ)
•
•
On chip DLL align DQ and DQS transition with CK
transition
JEDEC standard 400mil 66pin TSOP-II with 0.65mm
pin pitch
DM mask write data-in at the both rising and falling
edges of the data strobe
•
This product is in compliance with the direc-
tive pertaining of RoHS.
OPERATING FREQUENCY
ORDERING INFORMATION
Remark
(CL-tRCD-tRP)
Part No.
Configuration
Package
Grade
Clock Rate
H5DU2582GTR-XXI
32Mx8
400mil
66pin
- FA
- E3
- J3
- K2
- K3
250MHz@CL4
200MHz@CL3
166MHz@CL2.5
133MHz@CL2
133MHz@CL2.5
DDR500 (4-4-4)
DDR400 (3-3-3)
DDR333 (2.5-3-3)
DDR266A (2-3-3)
DDR266B (2.5-3-3)
16Mx16
H5DU2562GTR-XXI
TSOP-II
* X means speed grade
*ROHS (Restriction Of Hazardous Substances)
Rev. 1.0 / Jul. 2009
3
H5DU2562GTR-xxI
H5DU2582GTR-xxI
PIN CONFIGURATION
x8
x16
x16
x8
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
NC
VSS
DQ7
VSSQ
NC
1
2
VDD
DQ0
VDDQ
NC
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
NC
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
3
4
DQ6
VDDQ
NC
5
DQ1
VSSQ
NC
6
7
DQ5
VSSQ
NC
8
DQ2
VDDQ
NC
9
10
DQ4
VDDQ
NC
DQ3
VSSQ
NC
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
NC
NC
VSSQ
UDQS
NC
VSSQ
DQS
NC
VDDQ
NC
VDDQ
LDQS
NC
400mil X 875mil
66pin TSOP -II
NC
VREF
VSS
UDM
/CK
VREF
VSS
DM
VDD
NC
VDD
NC
0.65mm pin pitch
NC
LDM
/WE
(Lead free)
/CK
CK
/WE
/CAS
/RAS
/CS
CK
/CAS
/RAS
/CS
CKE
NC
CKE
NC
A12
A12
A11
A9
NC
NC
A11
BA0
BA1
A10/AP
A0
BA0
BA1
A10/AP
A0
A9
A8
A8
A7
A7
A6
A6
A1
A1
A5
A5
A2
A2
A4
A4
A3
A3
VSS
VSS
VDD
VDD
ROW AND COLUMN ADDRESS TABLE
ITEMS
32Mx8
16Mx16
Organization
Row Address
8M x 8 x 4banks
A0 - A12
A0-A9
4M x 16 x 4banks
A0 - A12
A0-A8
Column Address
Bank Address
Auto Precharge Flag
Refresh
BA0, BA1
A10
BA0, BA1
A10
8K
8K
Rev. 1.0 / Jul. 2009
4
H5DU2562GTR-xxI
H5DU2582GTR-xxI
PIN DESCRIPTION
PIN
TYPE
DESCRIPTION
Clock: CK and /CK are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of /CK. Output
(read) data is referenced to the crossings of CK and /CK (both directions of crossing).
CK, /CK
Input
Clock Enable: CKE HIGH activates, and CKE LOW deactivates internal clock signals, and
device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER
DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN (row
ACTIVE in any bank). CKE is synchronous for POWER DOWN entry and exit, and for SELF
REFRESH entry. CKE is asynchronous for SELF REFRESH exit, and for output disable. CKE
must be maintained high throughout READ and WRITE accesses. Input buffers, excluding
CK, /CK and CKE are disabled during POWER DOWN. Input buffers, excluding CKE are dis-
abled during SELF REFRESH. CKE is an SSTL_2 input, but will detect an LVCMOS LOW level
after VDD is applied.
CKE
Input
Chip Select: Enables or disables all inputs except CK, /CK, CKE, DQS and DM. All com-
mands are masked when CS is registered high. CS provides for external bank selection on
systems with multiple banks. CS is considered part of the command code.
/CS
Input
Input
Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVE, Read, Write or PRE-
CHARGE command is being applied.
BA0, BA1
Address Inputs: Provide the row address for ACTIVE commands, and the column address
and AUTO PRECHARGE bit for READ/WRITE commands, to select one location out of the
memory array in the respective bank. A10 is sampled during a precharge command to
determine whether the PRECHARGE applies to one bank (A10 LOW) or all banks (A10
HIGH). If only one bank is to be precharged, the bank is selected by BA0, BA1. The
address inputs also provide the op code during a MODE REGISTER SET command. BA0 and
BA1 define which mode register is loaded during the MODE REGISTER SET command (MRS
or EMRS).
A0 ~ A12
Input
Command Inputs: /RAS, /CAS and /WE (along with /CS) define the command being
entered.
/RAS, /CAS, /WE
Input
Input
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM
is sampled HIGH along with that input data during a WRITE access. DM is sampled on both
edges of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS
loading. For the x16, LDM corresponds to the data on DQ0-Q7; UDM corresponds to the
data on DQ8-Q15.
DM
(LDM,UDM)
Data Strobe: Output with read data, input with write data. Edge aligned with read data,
centered in write data. Used to capture write data. For the x16, LDQS corresponds to the
data on DQ0-Q7; UDQS corresponds to the data on DQ8-Q15.
DQS
(LDQS,UDQS)
I/O
DQ
VDD/VSS
VDDQ/VSSQ
VREF
I/O
Data input / output pin: Data bus
Supply
Supply
Supply
NC
Power supply for internal circuits and input buffers.
Power supply for output buffers for noise immunity.
Reference voltage for inputs for SSTL interface.
No connection.
NC
Rev. 1.0 / Jul. 2009
5
H5DU2562GTR-xxI
H5DU2582GTR-xxI
FUNCTIONAL BLOCK DIAGRAM (32Mx8)
4Banks x 8Mbit x 8 I/O Double Data Rate Synchronous DRAM
8
Write Data Register
DQS
DM
2-bit Prefetch Unit
16
Bank
8Mx8 / Bank0
8Mx8 / Bank1
8Mx8 / Bank2
8Mx8 / Bank3
Control
CLK
/CLK
CKE
/CS
/RAS
/CAS
/WE
16
8
Command
Decoder
DQ[0:7]
Mode
Register
Row
Decoder
Column Decoder
DQS
ADD
BA
Address
Buffer
Column Address
Counter
Data Strobe
Transmitter
CLK_DLL
DQS
Data Strobe
Receiver
CLK,
/CLK
DLL
Block
Mode
Register
Rev. 1.0 / Jul. 2009
6
H5DU2562GTR-xxI
H5DU2582GTR-xxI
FUNCTIONAL BLOCK DIAGRAM (16Mx16)
4Banks x 4Mbit x 16 I/O Double Data Rate Synchronous DRAM
16
Write Data Register
LDQS, UDQS
LDM, UDM
2-bit Prefetch Unit
32
Bank
4Mx16 / Bank0
4Mx16 / Bank1
4Mx16 / Bank2
4Mx16 / Bank3
Control
CLK
/CLK
CKE
/CS
/RAS
/CAS
/WE
32
16
Command
Decoder
DQ[0:15]
Mode
Register
Row
Decoder
Column Decoder
LDQS, UDQS
ADD
BA
Address
Buffer
Column Address
Counter
Data Strobe
CLK_DLL
Transmitter
LDQS
UDQS
Data Strobe
Receiver
CLK,
/CLK
DLL
Block
Mode
Register
Rev. 1.0 / Jul. 2009
7
H5DU2562GTR-xxI
H5DU2582GTR-xxI
SIMPLIFIED COMMAND TRUTH TABLE
Command
CKEn-1
CKEn
/CS
/RAS
/CAS
/WE
ADDR
A10/AP
OP code
OP code
BA
Extended Mode Register Set1,2
Mode Register Set1,2
Device Deselect1
No Operation1
H
H
X
X
L
L
L
L
L
L
L
L
H
L
X
H
L
X
H
H
X
H
H
H
H
H
X
X
X
X
Bank Active1
L
RA
V
V
Read1
L
H
L
L
L
L
H
H
L
L
L
H
L
CA
CA
X
Read with Autoprecharge1,3
Write1
H
H
X
X
V
Write with Autoprecharge1,4
Precharge All Banks1,5
Precharge selected Bank1
Read Burst Stop1
Auto Refresh1
H
H
L
X
V
H
L
H
H
H
X
H
L
L
L
L
H
L
H
L
L
H
H
X
X
L
L
Entry
X
H
L
X
H
X
H
X
H
X
V
X
H
X
H
X
H
X
V
X
H
X
H
X
H
X
V
Self Refresh1
Exit
L
H
L
H
L
H
L
Entry
Precharge Power
X
X
Down Mode1
H
L
H
Exit
H
L
H
L
L
Entry
Exit
Active Power
Down Mode1
H
X
( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation )
Note:
1. LDM/UDM states are Don’t Care. Refer to below Write Mask Truth Table.
2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Register setting during Extended MRS or MRS.
Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP
period from Precharge command.
3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+tRP).
4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+1+tWR+tRP). Write Recovery Time(tWR) is needed to guarantee that the last data has been
completely written.
5. If A10/AP is High when Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be precharged.
*For more information about Truth Table, refer to “Device Operation” section in Hynix website.
Rev. 1.0 / Jul. 2009
8
H5DU2562GTR-xxI
H5DU2582GTR-xxI
WRITE MASK TRUTH TABLE
/CS, /RAS,
/CAS, /WE
ADDR
Function
Data Write1
CKEn-1
CKEn
DM
A10/AP
BA
H
H
X
X
X
X
L
X
X
Data-In Mask1
H
Note:
1. Write Mask command masks burst write data with reference to LDQS/UDQS(Data Strobes) and it is not related with read data.
In case of x16 data I/O, LDM and UDM control lower byte(DQ0~7) and Upper byte(DQ8~15) respectively.
Rev. 1.0 / Jul. 2009
9
H5DU2562GTR-xxI
H5DU2582GTR-xxI
SIMPLIFIED STATE DIAGRAM
P o w er
A p p lied
P o w er
O n
P rec harg
e
P R E A LL
S elf
R e fresh
R E FS
R E FS X
R E FA
M R S
M R S
E M R S
A uto
R e fresh
Id le
C K E L
C K E H
A c tive
P o w er
D o w n
P re ch arg
e
P o w er
D o w n
A C T
C K E H
C K E L
B urst
S to p
R o w
A c tive
W rite
R ea d
W rite
R ead
W rite
A
R ea d
R ea d
A
W rite
R e ad
W rite
A
R ea d
A
R ea d
A
W rite
A
R ea d A
P R E
P R E
P R E
P rec ha rg
e
P R E
P R E A LL
A uto m atic S eq uen ce
C o m m an d S eq uen c e
P R E A LL = P recharg e A ll B anks
M R S = M o d e R eg ister S et
E M R S = E xtend ed M o d e R eg ister S et
R E F S = E nter S elf R efresh
R E F S X = E xit S elf R efresh
R E F A = A uto R efresh
C K E L = E n ter P o w er D o w n
C K E H = E xit P o w er D o w n
A C T = A c tive
W rite A = W rite w ith A uto p recharg e
R ead A = R ead w ith A uto p recharg e
P R E = P recharg e
Rev. 1.0 / Jul. 2009
10
H5DU2562GTR-xxI
H5DU2582GTR-xxI
POWER-UP SEQUENCE AND DEVICE INITIALIZATION
DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those
specified may result in undefined operation. Power must first be applied to VDD, then to VDDQ, and finally to VREF
(and to the system VTT). VTT must be applied after VDDQ to avoid device latch-up, which may cause permanent dam-
age to the device. VREF can be applied anytime after VDDQ, but is expected to be nominally coincident with VTT.
Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input, but will detect an
LVCMOS LOW level after VDD is applied. Maintaining an LVCMOS LOW level on CKE during power-up is required to
guarantee that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal oper-
ation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR
SDRAM requires a 200us delay prior to applying an executable command.
Once the 200us delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be
brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a EXTENDED
MODE REGISTER SET command should be issued for the Extended Mode Register, to enable the DLL, then a MODE
REGISTER SET command should be issued for the Mode Register, to reset the DLL, and to program the operating
parameters. After the DLL reset, tXSRD(DLL locking time) should be satisfied for read command. After the Mode Reg-
ister set command, a PRECHARGE ALL command should be applied, placing the device in the all banks idle state.
Once in the idle state, two AUTO REFRESH cycles must be performed. Additionally, a MODE REGISTER SET command
for the Mode Register, with the reset DLL bit deactivated low (i.e. to program operating parameters without resetting
the DLL) must be performed. Following these cycles, the DDR SDRAM is ready for normal operation.
1. Apply power - VDD, VDDQ, VTT, VREF in the following power up sequencing and attempt to maintain CKE at LVC-
MOS low state. (All the other input pins may be undefined.)
• VDD and VDDQ are driven from a single power converter output.
• VTT is limited to 1.44V (reflecting VDDQ(max)/2 + 50mV VREF variation + 40mV VTT variation.
• VREF tracks VDDQ/2.
• A minimum resistance of 42 Ohms (22 ohm series resistor + 22 ohm parallel resistor - 5% tolerance) limits the
input current from the VTT supply into any pin.
• If the above criteria cannot be met by the system design, then the following sequencing and voltage relation-
ship must be adhered to during power up.
Voltage description
Sequencing
Voltage relationship to avoid latch-up
< VDD + 0.3V
VDDQ
VTT
After or with VDD
After or with VDDQ
After or with VDDQ
< VDDQ + 0.3V
VREF
< VDDQ + 0.3V
2. Start clock and maintain stable clock for a minimum of 200usec.
3. After stable power and clock, apply NOP condition and take CKE high.
4. Issue Extended Mode Register Set (EMRS) to enable DLL.
5. Issue Mode Register Set (MRS) to reset DLL and set device to idle state with bit A8=high. (An additional 200
cycles(tXSRD) of clock are required for locking DLL)
6. Issue Precharge commands for all banks of the device.
7. Issue 2 or more Auto Refresh commands.
8. Issue a Mode Register Set command to initialize the mode register with bit A8 = Low
Rev. 1.0 / Jul. 2009
11
H5DU2562GTR-xxI
H5DU2582GTR-xxI
Power-Up Sequence
VDD
VDDQ
tVTD
VTT
VREF
/CLK
CLK
tIS tIH
LVCMOS Low Level
CKE
NOP
PRE
EMRS
MRS
NOP
PRE
AREF
MRS
ACT
RD
CMD
DM
CODE
CODE
CODE
CODE
CODE
CODE
CODE
CODE
CODE
CODE
ADDR
A10
BA0, BA1
DQS
CODE
CODE
CODE
CODE
CODE
DQ'S
T=200usec
tRP
tMRD
tMRD
tRP
tRFC
tMRD
tXSRD*
Power UP
VDD and CK stable
EMRS Set
MRS Set
(with A8=L)
MRS Set
Reset DLL
(with A8=H)
READ
Precharge All
Non-Read
Command
2 or more
Auto Refresh
Precharge All
* 200 cycle(tXSRD) of CK are required (for DLL locking) before Read Command
Rev. 1.0 / Jul. 2009
12
H5DU2562GTR-xxI
H5DU2582GTR-xxI
MODE REGISTER SET (MRS)
The mode register is used to store the various operating modes such as /CAS latency, addressing mode, burst length,
burst type, test mode, DLL reset. The mode register is programed via MRS command. This command is issued by the
low signals of /RAS, /CAS, /CS, /WE and BA0. This command can be issued only when all banks are in idle state and
CKE must be high at least one cycle before the Mode Register Set Command can be issued. Two cycles are required to
write the data in mode register. During the MRS cycle, any command cannot be issued. Once mode register field is
determined, the information will be held until reset by another MRS command.
BA1
0
BA0
0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
BT
A2
A1
A0
Operating Mode
CAS Latency
Burst Length
A6
0
A5
0
A4
0
CAS Latency
Reserved
Reserved
2
A3
0
Burst Type
Sequential
Interleave
BA0
MRS Type
MRS
0
1
0
0
1
1
EMRS
0
1
0
0
1
1
3
1
0
0
Reserved
1.5
1
0
1
Burst Length
A2
A1
A0
1
1
0
2.5
Sequential
Reserved
2
Interleave
Reserved
2
1
1
1
Reserved
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
4
4
A12~A9 A8
A7 A6~A0
Operating Mode
8
8
0
0
0
-
0
1
0
-
0
0
1
-
Valid
Normal Operation
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Valid
VS
-
Normal Operation/ Reset DLL
Vendor specific Test Mode
All other states reserved
Rev. 1.0 / Jul. 2009
13
H5DU2562GTR-xxI
H5DU2582GTR-xxI
BURST DEFINITION
Burst Length
Starting Address (A2,A1,A0)
Sequential
0, 1
Interleave
0, 1
XX0
XX1
X00
X01
X10
X11
000
001
010
011
100
101
110
111
2
1, 0
1, 0
0, 1, 2, 3
0, 1, 2, 3
1, 2, 3, 0
1, 0, 3, 2
4
2, 3, 0, 1
2, 3, 0, 1
3, 0, 1, 2
3, 2, 1, 0
0, 1, 2, 3, 4, 5, 6, 7
1, 2, 3, 4, 5, 6, 7, 0
2, 3, 4, 5, 6, 7, 0, 1
3, 4, 5, 6, 7, 0, 1, 2
4, 5, 6, 7, 0, 1, 2, 3
5, 6, 7, 0, 1, 2, 3, 4
6, 7, 0, 1, 2, 3, 4, 5
7, 0, 1, 2, 3, 4, 5, 6
0, 1, 2, 3, 4, 5, 6, 7
1, 0, 3, 2, 5, 4, 7, 6
2, 3, 0, 1, 6, 7, 4, 5
3, 2, 1, 0, 7, 6, 5, 4
4, 5, 6, 7, 0, 1, 2, 3
5, 4, 7, 6, 1, 0, 3, 2
6, 7, 4, 5, 2, 3, 0, 1
7, 6, 5, 4, 3, 2, 1, 0
8
BURST LENGTH & TYPE
Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being programmable. The burst
length determines the maximum number of column locations that can be accessed for a given Read or Write com-
mand. Burst lengths of 2, 4 or 8 locations are available for both the sequential and the interleaved burst types.
Reserved states should not be used, as unknown operation or incompatibility with future versions may result.
When a Read or Write command is issued, a block of columns equal to the burst length is effectively selected. All
accesses for that burst take place within this block, meaning that the burst wraps within the block if a boundary is
reached. The block is uniquely selected by A1-Ai when the burst length is set to two, by A2 -Ai when the burst length
is set to four and by A3 -Ai when the burst length is set to eight (where Ai is the most significant column address bit
for a given configuration). The remaining (least significant) address bit(s) is (are) used to select the starting location
within the block. The programmed burst length applies to both Read and Write bursts.
Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the
burst type and is selected via bit A3. The ordering of accesses within a burst is determined by the burst length, the
burst type and the starting column address, as shown in Burst Definition Table
Rev. 1.0 / Jul. 2009
14
H5DU2562GTR-xxI
H5DU2582GTR-xxI
CAS LATENCY
The Read latency or CAS latency is the delay in clock cycles between the registration of a Read command and the
availability of the first burst of output data. The latency can be programmed 2 or 2.5 clocks for DDR200/266/333 and
3 clocks for DDR400.
If a Read command is registered at clock edge n, and the latency is m clocks, the data is available nominally coincident
with clock edge n + m.
Reserved states should not be used as unknown operation or incompatibility with future versions may result.
DLL RESET
The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon return-
ing to normal operation after having disabled the DLL for the purpose of debug or evaluation. The DLL is automatically
disabled when entering self refresh operation and is automatically re-enabled upon exit of self refresh operation. Any
time the DLL is enabled, 200 clock cycles must occur to allow time for the internal clock to lock to the externally
applied clock before an any command can be issued.
OUTPUT DRIVER IMPEDANCE CONTROL
The normal drive strength for all outputs is specified to be SSTL_2, Class II. Hynix also supports a half strength driver
option, intended for lighter load and/or point-to-point environments. Selection of the half strength driver option will
reduce the output drive strength by 50% of that of the full strength driver. I-V curves for both the full strength driver
and the half strength driver are included in this document.
Rev. 1.0 / Jul. 2009
15
H5DU2562GTR-xxI
H5DU2582GTR-xxI
EXTENDED MODE REGISTER SET (EMRS)
The Extended Mode Register controls functions beyond those controlled by the Mode Register; these additional func-
tions include DLL enable/disable, output driver strength selection(optional). These functions are controlled via the bits
shown below. The Extended Mode Register is programmed via the Mode Register Set command (BA0=1 and BA1=0)
and will retain the stored information until it is programmed again or the device loses power.
The Extended Mode Register must be loaded when all banks are idle and no bursts are in progress, and the controller
must wait the specified time before initiating any subsequent operation. Violating either of these requirements will
result in unspecified operation.
BA1 BA0 A12 A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
0*
A1
DS
A0
0
1
Operating Mode
DLL
A0
0
DLL enable
Enable
BA0
0
MRS Type
MRS
1
Disable
1
EMRS
Output Driver
A1
Impedance Control
Full Strength Driver
Half Strength Driver
0
1
An~A3
A2~A0
Operating Mode
Normal Operation
0
_
Valid
_
All other states reserved
* This part do not support/QFC function, A2 must be programmed to Zero.
Rev. 1.0 / Jul. 2009
16
H5DU2562GTR-xxI
H5DU2582GTR-xxI
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
oC
Operating Temperature (Ambient)
TA
-40 ~ 85
oC
V
Storage Temperature
TSTG
VDD
-55 ~ 150
-1.0 ~ 3.6
-1.0 ~ 3.6
-1.0 ~ 3.6
-0.5 ~3.6
50
Voltage on VDD relative to VSS
Voltage on VDDQ relative to VSS
Voltage on inputs relative to VSS
Voltage on I/O pins relative to VSS
Output Short Circuit Current
Soldering Temperature ⋅ Time
VDDQ
VINPUT
VIO
V
V
V
IOS
mA
oC ⋅ Sec
TSOLDER
260 ⋅ 10
Note: Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITIONS (TA=-40 to 85 oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Min
Typ.
Max
Unit
Power Supply Voltage
Power Supply Voltage 1
VDD
2.3
2.3
2.5
2.5
2.7
2.7
V
V
VDDQ
Input High Voltage
VIH
VIL
VREF + 0.15
-0.3
-
-
VDDQ + 0.3
VREF - 0.15
V
V
Input Low Voltage2
Termination Voltage
Reference Voltage3
VTT
VREF - 0.04
0.49*VDDQ
VREF
VREF + 0.04
0.51*VDDQ
V
V
VREF
0.5*VDDQ
Input Voltage Level, CK and CK inputs
VIN(DC)
VID(DC)
VI(RATIO)
ILI
-0.3
0.36
0.71
-2
-
-
-
-
-
VDDQ+0.3
V
V
Input Differential Voltage, CK and CK inputs4
V-I Matching: Pullup to Pulldown Current Ratio5
Input Leakage Current6
VDDQ+0.6
1.4
2
-
uA
uA
Output Leakage Current7
ILO
-5
5
Output High Current
IOH
IOL
IOH
IOL
-16.8
16.8
-13.6
13.6
-
-
-
-
-
-
-
-
mA
mA
mA
mA
Normal Strength
(min VDDQ, min VREF, min VTT)
Output Driver
Output Low Current
(VOUT=VTT ± 0.84)
(min VDDQ, max VREF, max VTT)
Output High Current
Half Strength Out-
(min VDDQ, min VREF, min VTT)
put Driver
Output Low Current
(VOUT=VTT ± 0.68)
(min VDDQ, max VREF, max VTT)
Note:
1. VDDQ must not exceed the level of VDD.
2. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of duration.
3. VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of the same.
Peak to peak noise on VREF may not exceed ± 2% of the DC value.
4. VID is the magnitude of the difference between the input level on CK and the input level on /CK.
5. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the entire temper-
ature and voltage range, for device drain to source voltages from 0.25V to 1.0V. For a given output, it represents the maximum dif-
ference between pullup and pulldown drivers due to process variation. The full variation in the ratio of the maximum to minimum
pullup and pulldown current will not exceed 1/7 for device drain to source voltages from 0.1 to 1.0.
6. VIN=0 to VDD, All other pins are not tested under VIN =0V.
7. DQs are disabled, VOUT=0 to VDDQ
Rev. 1.0 / Jul. 2009
17
H5DU2562GTR-xxI
H5DU2582GTR-xxI
IDD SPECIFICATION AND CONDITIONS (TA=-40 to 85 oC, Voltage referenced to VSS = 0V)
Test Conditions
Test Condition
Symbol
Operating Current:
One bank; Active - Precharge; tRC=tRC(min); tCK=tCK(min); DQ,DM and DQS inputs changing twice per clock
cycle; address and control inputs changing once per clock cycle
IDD0
Operating Current:
One bank; Active - Read - Precharge;
IDD1
Burst Length=2; tRC=tRC(min); tCK=tCK(min); address and control inputs changing once per clock cycle
Precharge Power Down Standby Current:
All banks idle; Power down mode; CKE=Low, tCK=tCK(min)
IDD2P
Idle Standby Current:
/CS=High, All banks idle; tCK=tCK(min);
CKE=High; address and control inputs changing once per clock cycle.
VIN=VREF for DQ, DQS and DM
IDD2F
Idle Quiet Standby Current:
/CS>=Vih(min); All banks idle; CKE>=Vih(min); Addresses and other control inputs stable, Vin=Vref for DQ, DQS
and DM
IDD2Q
IDD3P
Active Power Down Standby Current:
One bank active; Power down mode; CKE=Low, tCK=tCK(min)
Active Standby Current:
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge; tRC=tRAS(max); tCK=tCK(min);
DQ, DM and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock
cycle
IDD3N
Operating Current:
Burst=2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle;
tCK=tCK(min); IOUT=0mA
IDD4R
IDD4W
IDD5
Operating Current:
Burst=2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle;
tCK=tCK(min); DQ, DM and DQS inputs changing twice per clock cycle
Auto Refresh Current:
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz, 10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
tRC=tRFC(min) - 14*tCK for DDR400 at 200Mhz
Self Refresh Current:
CKE =< 0.2V; External clock on; tCK=tCK(min)
IDD6
IDD7
Operating Current - Four Bank Operation:
Four bank interleaving with BL=4
Rev. 1.0 / Jul. 2009
18
H5DU2562GTR-xxI
H5DU2582GTR-xxI
IDD Specification
32Mx8
Speed
DDR500 DDR400B DDR333 DDR266A DDR266B
Parameter
Symbol
Unit
Operating Current
IDD0
IDD1
60
70
55
65
50
60
3
50
60
3
50
60
3
mA
mA
mA
mA
mA
mA
mA
Operating Current
Precharge Power Down Standby Current
Idle Standby Current
IDD2P
IDD2F
IDD2Q
IDD3P
IDD3N
IDD4R
IDD4W
IDD5
4
4
25
20
20
18
15
30
120
120
90
3
20
20
Idle Quiet Standby Current
Active Power Down Standby Current
Active Standby Current
Operating Current
22
18
18
15
18
15
15
15
30
30
30
120
120
90
3
30
120
120
90
3
140
140
110
3
130
130
100
3
Operating Current
mA
Auto Refresh Current
Normal
Self Refresh Current
mA
mA
mA
IDD6
IDD7
Low Power
1.5
220
1.5
210
1.5
200
1.5
200
1.5
200
Operating Current - Four Bank Operation
16Mx16
Speed
Parameter
Symbol
Unit
DDR500 DDR400B DDR333 DDR266A DDR266B
Operating Current
IDD0
IDD1
60
70
55
65
50
60
3
50
60
3
50
60
3
mA
mA
mA
mA
mA
mA
mA
Operating Current
Precharge Power Down Standby Current
Idle Standby Current
IDD2P
IDD2F
IDD2Q
IDD3P
IDD3N
IDD4R
IDD4W
IDD5
4
4
25
20
20
18
15
30
120
120
90
3
20
20
Idle Quiet Standby Current
Active Power Down Standby Current
Active Standby Current
Operating Current
22
18
18
15
18
15
15
15
30
30
30
120
120
90
3
30
120
120
90
3
140
140
110
3
130
130
100
3
Operating Current
mA
Auto Refresh Current
Normal
Self Refresh Current
mA
mA
mA
IDD6
IDD7
Low Power
1.5
220
1.5
210
1.5
200
1.5
200
1.5
200
Operating Current - Four Bank Operation
Rev. 1.0 / Jul. 2009
19
H5DU2562GTR-xxI
H5DU2582GTR-xxI
AC OPERATING CONDITIONS (TA=-40 to 85 oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Min
Max
Unit
Input High (Logic 1) Voltage, DQ, DQS and DM signals
Input Low (Logic 0) Voltage, DQ, DQS and DM signals
VIH(AC)
VIL(AC)
VID(AC)
VREF + 0.31
-
V
V
V
-
VREF - 0.31
VDDQ + 0.6
Input Differential Voltage, CK and /CK inputs1
Input Crossing Point Voltage, CK and /CK inputs2
0.7
VIX(AC)
0.5*VDDQ-0.2
0.5*VDDQ+0.2
V
Note:
1. VID is the magnitude of the difference between the input level on CK and the input on /CK.
2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same.
*For more information about AC Overshoot/Undershoot Specifications, refer to “Device Operation” section in hynix website.
AC OPERATING TEST CONDITIONS (TA=-40 to 85oC, Voltage referenced to VSS = 0V)
Parameter
Value
Unit
Reference Voltage
VDDQ x 0.5
V
V
Termination Voltage
VDDQ x 0.5
AC Input High Level Voltage (VIH, min)
AC Input Low Level Voltage (VIL, max)
Input Timing Measurement Reference Level Voltage
Output Timing Measurement Reference Level Voltage
Input Signal maximum peak swing
VREF + 0.31
V
VREF - 0.31
V
VREF
VTT
1.5
1
V
V
V
Input minimum Signal Slew Rate
V/ns
Termination Resistor (RT)
50
Ω
W
pF
Series Resistor (RS)
25
Output Load Capacitance for Access Time Measurement (CL)
30
Rev. 1.0 / Jul. 2009
20
H5DU2562GTR-xxI
H5DU2582GTR-xxI
AC CHARACTERISTICS (note: 1 - 9 / AC operating conditions unless otherwise noted)
DDR500
DDR400B
DDR333
DDR266A
DDR266B
UN
IT
Parameter
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Row Cycle Time
tRC
48
-
55
-
60
-
65
-
65
-
ns
ns
Auto Refresh Row Cycle
Time
tRFC
tRAS
tRAP
56
32
-
70
40
-
72
42
-
75
45
-
120K
-
75
45
-
Row Active Time
70K
-
70K
-
70K
-
120K ns
Active to Read with
tRCD or
tRASmin
tRCD or
tRASmin
tRCD or
tRASmin
tRCD or
tRASmin
tRCD or
tRASmin
-
-
-
-
ns
ns
Auto Precharge Delay
Row Address to Column
Address Delay
tRCD
tRRD
tCCD
16
8
-
-
-
15
10
1
-
-
-
18
12
1
-
-
-
20
15
1
-
-
-
20
15
1
Row Active to Row
Active Delay
ns
Column Address to
Column Address Delay
1
tCK
Row Precharge Time
Write Recovery Time
tRP
16
15
-
-
15
15
-
-
18
15
-
-
20
15
-
-
20
15
-
-
ns
ns
tWR
Internal Write to Read
Command Delay
tWTR
2
-
2
-
1
-
1
-
1
-
tCK
Auto Precharge Write
Recovery + Precharge
Time22
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
tDAL
-
-
-
-
-
tCK
CL = 4
4
7
ns
ns
System
Clock Cycle
CL = 3
5
10
12
-
-
-
-
-
-
tCK
CL = 2.5
Time24
6
6
12
7.5
12
7.5
12 ns
12 ns
CL = 2
Clock High Level Width
Clock Low Level Width
7.5
0.45
0.45
12
7.5
0.45
0.45
12
7.5
12
10
tCH
tCL
0.45
0.45
0.55
0.55
0.55
0.55
0.55
0.55
0.45
0.45
0.55
0.55
0.45
0.45
0.55 tCK
0.55 tCK
Data-Out edge to Clock
edge Skew
tAC
-0.65 0.65
-0.7
0.7
-0.7
-0.6
-
0.7
0.6
-0.75 0.75 -0.75 0.75 ns
-0.75 0.75 -0.75 0.75 ns
DQS-Out edge to Clock
edge Skew
tDQSCK -0.55 0.55 -0.55 0.55
DQS-Out edge to Data-
Out edge Skew21
tDQSQ
tQH
-
0.35
-
0.4
-
0.45
-
0.5
-
0.5 ns
Data-Out hold time
from DQS20
tHP
-tQHS
tHP
-tQHS
tHP
-tQHS
tHP
-tQHS
tHP
-tQHS
-
-
-
-
-
-
-
-
ns
ns
min
(tCL,tCH)
min
(tCL,tCH)
min
(tCL,tCH)
min
(tCL,tCH)
min
(tCL,tCH)
Clock Half Period19,20
tHP
-
Data Hold Skew
Factor20
tQHS
tDV
-
0.5
-
0.5
-
0.55
-
0.75
-
0.75 ns
Valid Data Output
Window
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ
tQH-tDQSQ ns
Rev. 1.0 / Jul. 2009
21
H5DU2562GTR-xxI
H5DU2582GTR-xxI
- Continue
DDR500 DDR400B DDR333 DDR266A DDR266B
Min Max Min Max Min Max Min Max Min Max
UN
IT
Parameter
Symbol
Data-out high-impedance window
from CK,/CK10
tHZ
tLZ
tIS
tIH
tIS
-0.65 0.65 -0.7 0.7 -0.7 0.7 -0.75 0.75 -0.75 0.75 ns
-0.65 0.65 -0.7 0.7 -0.7 0.7 -0.75 0.75 -0.75 0.75 ns
Data-out low-impedance window
from CK, /CK10
Input Setup Time (fast slew
rate)14,16-18
0.6
0.6
0.6
-
-
-
-
0.6
0.6
0.7
0.7
-
-
-
-
0.75
0.75
0.8
-
-
-
-
0.9
0.9
1.0
1.0
-
-
-
-
0.9
0.9
1.0
1.0
-
-
-
-
ns
ns
ns
ns
Input Hold Time (fast slew
rate)14,16-18
Input Setup Time (slow slew
rate)15-18
Input Hold Time (slow slew
rate)15-18
tIH
0.6
2.2
0.8
Input Pulse Width17
tIPW
-
-
-
2.2
-
-
-
2.2
-
-
-
2.2
-
-
-
2.2
-
-
-
ns
Write DQS High Level Width
Write DQS Low Level Width
tDQSH 0.35
tDQSL 0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
tCK
tCK
Clock to First Rising edge of DQS-
In
tDQSS 0.72 1.25 0.72 1.25 0.75 1.25 0.75 1.25 0.75 1.25 tCK
DQS falling edge to CK setup time
tDSS
tDSH
0.2
0.2
-
-
0.2
0.2
-
-
0.2
0.2
-
-
0.2
0.2
-
-
0.2
0.2
-
-
tCK
tCK
DQS falling edge hold time from
CK
DQ & DM input setup time25
DQ & DM input hold time25
tDS
tDH
0.4
0.4
-
-
-
0.4
0.4
-
-
0.45
0.45
-
-
0.5
0.5
-
-
0.5
0.5
-
-
-
ns
ns
ns
DQ & DM Input Pulse Width17
Read DQS Preamble Time
Read DQS Postamble Time
tDIPW 1.6
1.75
-
1.1
0.6
-
1.75
0.9
0.4
0
-
1.1
0.6
-
1.75
0.9
0.4
0
-
1.1
0.6
-
1.75
0.9
0.4
0
tRPRE
tRPST
0.9
0.4
0
1.1 0.9
0.6 0.4
1.1 tCK
0.6 tCK
Write DQS Preamble Setup Time12
Write DQS Preamble Hold Time
tWPRES
-
-
0
-
-
ns
tWPREH 0.25
tWPST 0.4
0.25
-
0.25
0.4
2
-
0.25
0.4
2
-
0.25
0.4
2
tCK
Write DQS Postamble Time11
Mode Register Set Delay
0.6 0.4
0.6
-
0.6
-
0.6
-
0.6 tCK
tMRD
2
-
-
2
-
-
tCK
ns
Exit Self Refresh to non-Read
command23
tXSNR
75
75
-
-
75
200
-
-
-
75
200
-
-
-
75
200
-
Exit Self Refresh to Read
command
tXSRD 200
-
200
-
-
tCK
us
Average Periodic Refresh
Interval13,25
tREFI
-
7.8
7.8
7.8
7.8
7.8
Rev. 1.0 / Jul. 2009
22
H5DU2562GTR-xxI
H5DU2582GTR-xxI
Note:
1. All voltages referenced to Vss.
2. Tests for ac timing, IDD, and electrical, ac and dc characteristics, may be conducted at nominal reference/supply voltage levels,
but the related specifications and device operation are guaranteed for the full voltage range specified.
3. Below figure represents the timing reference load used in defining the relevant timing parameters of the part. It is not intended to
be either a precise representation of the typical system environment nor a depiction of the actual load presented by a production
tester. System designers will use IBIS or other simulation tools to correlate the timing reference load to a system environment.
Manufacturers will correlate to their production test conditions (generally a coaxial transmission line terminated at the tester elec-
tronics).
VDDQ
50 Ω
Output
(VOUT)
30 pF
Figure: Timing Reference Load
4. AC timing and IDD tests may use a VIL to VIHswing of up to 1.5 V in the test environment, but input timing is still referenced to
VREF (or to the crossing point for CK, /CK), and parameter specifications are guaranteed for the specified ac input levels under
normal use conditions. The minimum slew rate for the input signals is 1 V/ns in the range between VIL(ac) and VIH(ac).
5. The ac and dc input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result
of the signal crossing the ac input level and will remain in that state as long as the signal does not ring back above (below) the
dc input LOW (HIGH) level.
6. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE < 0.2VDDQ is
recognized as LOW.
7. The CK, /CK input reference level (for timing referenced to CK, /CK) is the point at which CK and /CK cross; the input reference
level for signals other than CK, /CK is VREF.
8. The output timing reference voltage level is VTT.
9. Operation or timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must
be powered down and then restarted through the specified initialization sequence before normal operation can continue.
10. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to
a specific voltage level but specify when the device output is no longer driving (HZ), or begins driving (LZ).
11. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but
system performance (bus turnaround) will degrade accordingly.
12. The specific requirement is that DQS be valid (HIGH, LOW, or at some point on a valid transition) on or before this CK edge. A
valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previ-
ously in progress on the bus, DQS will be transitioning from High-Z to logic LOW. If a previous write was in progress, DQS could
be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS.
13. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM device.
14. For command/address input slew rate ≥ 1.0 V/ns.
15. For command/address input slew rate ≥ 0.5 V/ns and < 1.0 V/ns
16. For CK & /CK slew rate ≥ 1.0 V/ns (single-ended)
17. These parameters guarantee device timing, but they are not necessarily tested on each device.
They may be guaranteed by device design or tester correlation.
18. Slew Rate is measured between VOH(ac) and VOL(ac).
19. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this
value can be greater than the minimum specification limits for tCL and tCH).
For example, tCL and tCH are = 50% of the period, less the half period jitter (tJIT(HP)) of the clock source, and less the half
period jitter due to crosstalk (tJIT(crosstalk)) into the clock traces.
Rev. 1.0 / Jul. 2009
23
H5DU2562GTR-xxI
H5DU2582GTR-xxI
20.tQH = tHP - tQHS, where:
tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS accounts for 1) The
pulse duration distortion of on-chip clock circuits; and 2) The worst case push--out of DQS on one transition followed by the
worst case pull--in of DQ on the next transition, both of which are, separately, due to data pin skew and output pattern effects,
and p-channel to n-channel variation of the output drivers.
21. tDQSQ:
Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers for any given
cycle.
22. tDAL = (tWR/tCK) + (tRP/tCK)
For each of the terms above, if not already an integer, round to the next highest integer.
Example: For DDR266B at CL=2.5 and tCK=7.5 ns
tDAL = ((15 ns / 7.5 ns) + (20 ns / 7.5 ns)) clocks
= ((2) + (3)) clocks
= 5 clocks
23. In all circumstances, tXSNR can be satisfied using
tXSNR = tRFCmin + 1*tCK
24. The only time that the clock frequency is allowed to change is during self-refresh mode.
25. If refresh timing or tDS/tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid
READ can be executed.
Rev. 1.0 / Jul. 2009
24
H5DU2562GTR-xxI
H5DU2582GTR-xxI
SYSTEM CHARACTERISTICS CONDITIONS for DDR SDRAMS
The following tables are described specification parameters that required in systems using DDR devices to ensure
proper performannce. These characteristics are for system simulation purposes and are guaranteed by design.
Input Slew Rate for DQ/DM/DQS (Table a.)
AC CHARACTERISTICS
DDR500
DDR400
DDR333
DDR266
DDR200
UNIT Note
PARAMETER
Symbol min max min max min max min max min max
DQ/DM/DQS input slew rate
measured between VIH(DC),
VIL(DC) and VIL(DC), VIH(DC)
DCSLEW 0.5
4.0
0.5
4.0
0.5
4.0
0.5
4.0
0.5
4.0
V/ns
1,12
Address & Control Input Setup & Hold Time Derating (Table b.)
Input Slew Rate
0.5 V/ns
Delta tIS
0
Delta tIH
UNIT
ps
Note
0
0
0
9
9
9
0.4 V/ns
+50
ps
0.3 V/ns
+100
ps
DQ & DM Input Setup & Hold Time Derating (Table c.)
Input Slew Rate
0.5 V/ns
Delta tDS
0
Delta tDH
UNIT
ps
Note
11
0
0
0
0.4 V/ns
+75
ps
11
0.3 V/ns
+150
ps
11
DQ & DM Input Setup & Hold Time Derating for Rise/Fall Delta Slew Rate (Table d.)
Input Slew Rate
Delta tDS
0
Delta tDH
UNIT
ps
Note
10
0
± 0.0 ns/V
+50
+50
+100
ps
10
± 0.25 ns/V
± 0.5 ns/V
+100
ps
10
Output Slew Rate Characteristics (for x8 Devices) (Table e.)
Typical Range (V/
Slew Rate Characteristic
Minimum (V/ns)
Maximum (V/ns)
Note
ns)
Pullup Slew Rate
1.2 - 2.5
1.2 - 2.5
1.0
1.0
4.5
4.5
1,3,4,6,7,8
2,3,4,6,7,8
Pulldown Slew Rate
Output Slew Rate Characteristics (for x16 Device) (Table f.)
Typical Range (V/
Slew Rate Characteristic
Minimum (V/ns)
Maximum (V/ns)
Note
ns)
Pullup Slew Rate
1.2 - 2.5
1.2 - 2.5
1.0
1.0
4.5
4.5
1,3,4,6,7,8
2,3,4,6,7,8
Pulldown Slew Rate
Output Slew Rate Matching Ratio Characteristics (Table g.)
Slew Rate Characteristic
Parameter
DDR266A
DDR266B
DDR200
Note
min
max
min
max
min
max
Output Slew Rate Matching Ratio
(Pullup to Pulldown)
-
-
-
-
0.71
1.4
5,12
Rev. 1.0 / Jul. 2009
25
H5DU2562GTR-xxI
H5DU2582GTR-xxI
Note:
1. Pullup slew rate is characterized under the test conditions as shown in below Figure.
Test Point
Output
(VOUT)
Ω
50
VSSQ
Figure: Pullup Slew rate
2. Pulldown slew rate is measured under the test conditions shown in below Figure.
VDDQ
Ω
50
Output
(VOUT)
Test Point
Figure: Pulldown Slew rate
3. Pullup slew rate is measured between (VDDQ/2 - 320 mV ± 250mV)
Pulldown slew rate is measured between (VDDQ/2 + 320mV ± 250mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example: For typical slew, DQ0 is switching
For minimum slew rate, all DQ bits are switching worst case pattern
For maximum slew rate, only one DQ is switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
4. Evaluation conditions
Typical: 25 oC (Ambient), VDDQ = nominal, typical process
Minimum: 70 oC (Ambient), VDDQ = minimum, slow-slow process
Maximum: 0 oC (Ambient), VDDQ = Maximum, fast-fast process
5. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature
and voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process
variation.
6. Verified under typical conditions for qualification purposes.
7. TSOP-II package devices only.
8. Only intended for operation up to 256 Mbps per pin.
9. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5 V/ns as shown in Table b.
The Input slew rate is based on the lesser of the slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), sim-
ilarly for rising transitions.
10. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables c
& d. Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, fall rate. Input slew rate is based on
the lesser of the slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions. The
delta rise/fall rate is calculated as:
{1/(Slew Rate1)} - {1/(slew Rate2)}
For example:
If Slew Rate 1 is 0.5 V/ns and Slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is -0.5 ns/V. Using the table given, this would
result in the need for an increase in tDS and tDH of 100ps.
11. Table c is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the
lesser of the AC-AC slew rate and the DC-DC slew rate. The input slew rate is based on the lesser of the slew rates determined by
either VIH(ac) to VIL(AC) or VIH(DC) to VIL(DC), and similarly for rising transitions.
12. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal tran-
sitions through the DC region must be monotonic.
Rev. 1.0 / Jul. 2009
26
H5DU2562GTR-xxI
H5DU2582GTR-xxI
CAPACITANCE (TA=25oC, f=100MHz)
Parameter
Pin
Symbol
Min
Max
Unit
Input Clock Capacitance
Delta Input Clock Capacitance
Input Capacitance
CK, /CK
CK, /CK
CI1
Delta CI1
CI1
2.0
-
3.0
0.25
3.0
0.5
5.0
0.5
pF
pF
pF
pF
pF
pF
All other input-only pins
All other input-only pins
DQ, DQS, DM
2.0
-
Delta Input Capacitance
Input / Output Capacitance
Delta Input / Output Capacitance
Delta CI2
CIO
4.0
-
DQ, DQS, DM
Delta CIO
Note:
1. VDD = min. to max., VDDQ = 2.3V to 2.7V, VODC = VDDQ/2, VOpeak-to-peak = 0.2V
2. Pins not under test are tied to GND.
3. These values are guaranteed by design and are tested on a sample basis only.
OUTPUT LOAD CIRCUIT
VTT
RT=50Ω
Output
Zo=50Ω
VREF
CL=30pF
Rev. 1.0 / Jul. 2009
27
H5DU2562GTR-xxI
H5DU2582GTR-xxI
PACKAGE INFORMATION
400mil 66pin Thin Small Outline Package
max
min
,
Unit : mm(Inch)
11.94 (0.470)
11.79 (0.462)
10.26 (0.404)
10.05 (0.396)
BASE PLANE
22.33 (0.879)
22.12 (0.871)
0 ~ 5 Deg.
0.35 (0.0138)
0.65 (0.0256) BSC
0.25 (0.0098)
SEATING PLANE
1.194 (0.0470)
0.991 (0.0390)
0.15 (0.0059)
0.05 (0.0020)
0.597 (0.0235)
0.406 (0.0160)
0.210 (0.0083)
0.120 (0.0047)
Rev. 1.0 / Jul. 2009
28
相关型号:
H5DU2562GTR-K2L
DDR DRAM, 16MX16, 0.75ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2562GTR-K3
DDR DRAM, 16MX16, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2562GTR-K3L
DDR DRAM, 16MX16, 0.75ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-E3
DDR DRAM, 32MX8, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-FA
DDR DRAM, 32MX8, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-FAC
DDR DRAM, 32MX8, 0.65ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-FAI
DDR DRAM, 32MX8, 0.65ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-FAJ
DDR DRAM, 32MX8, 0.65ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-FAL
DDR DRAM, 32MX8, 0.65ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-J3L
DDR DRAM, 32MX8, 0.7ns, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
H5DU2582GTR-K2
DDR DRAM, 32MX8, CMOS, PDSO66, 0.400 X 0.875 INCH, 0.65 MM PITCH, ROHS COMPLIANT, TSOP2-66
HYNIX
©2020 ICPDF网 联系我们和版权申明