HMA82GS7AFR8N-UH [HYNIX]
DDR4 SDRAM SO-DIMM Based on 8Gb A-die;型号: | HMA82GS7AFR8N-UH |
厂家: | HYNIX SEMICONDUCTOR |
描述: | DDR4 SDRAM SO-DIMM Based on 8Gb A-die 动态存储器 双倍数据速率 |
文件: | 总73页 (文件大小:1643K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
260pin DDR4 SDRAM SODIMM
DDR4 SDRAM SO-DIMM
Based on 8Gb A-die
HMA851S6AFR6N
HMA81GS6AFR8N
HMA81GS7AFR8N
HMA82GS6AFR8N
HMA82GS7AFR8N
*SK hynix reserves the right to change products or specifications without notice.
Rev. 1.4 / Sep.2017
1
Revision History
Revision No.
History
Draft Date
Oct.2015
Remark
0.01
0.1
Initial Release
Added Development plan (1Rx16)
Updated JEDEC Specification
Deleted Speed Grade Table
Dec.2015
0.2
Added Development plan (ECC 1Rx8/2Rx8)
Updated 2133Mbps (tCK(min) : 0.938ns->0.937ns)
Updated JEDEC Specification
Mar.2016
Updated IDD Specification
1.0
1.1
1.2
1.3
1.4
Updated IDD Specification (1Rx16)
Updated IPP Specification (1Rx8/2Rx8)
Updated IDD Specification (2133Mbps)
Corrected Module Dimension : 1Rx16 / thickness
Corrected Block Diagram / Module Dimension
Apr.2016
Apr.2016
Jun.2016
Aug.2016
Sep.2017
Rev. 1.4 / Sep.2017
2
Description
SK hynix Unbuffered Small Outline DDR4 SDRAM DIMMs (Unbuffered Small Outine Double Data Rate Syn-
chronous DRAM Dual In-Line Memory Modules) are low power, high-speed operation memory modules
that use DDR4 SDRAM devices. These DDR4 SDRAM Unbuffered Small Outline DIMMs are intended for use
as main memory when installed in systems such as micro servers and mobile personal computres.
Features
• Power Supply: VDD=1.2V (1.14V to 1.26V)
• VDDQ = 1.2V (1.14V to 1.26V)
• VPP - 2.5V (2.375V to 2.75V)
• VDDSPD=2.25V to 3.6V
• Functionality and operations comply with the DDR4 SDRAM datasheet
• 16 internal banks
• Bank Grouping is applied, and CAS to CAS latency (tCCD_L, tCCD_S) for the banks in the same or dif-
ferent bank group accesses are available
• Data transfer rates: PC4-2400, PC4-2133, PC4-1866, PC4-1600
• Bi-Directional Differential Data Strobe
• 8 bit pre-fetch
• Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)
• Supports ECC error correction and detection
• On-Die Termination (ODT)
• Temperature sensor with integrated SPD
• This product is in compliance with the RoHS directive.
• Per DRAM Addressability is supported
• Internal Vref DQ level generation is available
Ordering Information
# of
ranks
Part Number
Density
Organization
Component Composition
HMA851S6AFR6N-TF/UH
HMA81GS6AFR8N-TF/UH
HMA81GS7AFR8N-TF/UH
HMA82GS6AFR8N-TF/UH
HMA82GS7AFR8N-TF/UH
4GB
8GB
512Mx64
1Gx64
1Gx72
2Gx64
2Gx72
512Mx16(H5AN8G6NAFR)*4
1Gx8(H5AN8G8NAFR)*8
1Gx8(H5AN8G8NAFR)*9
1Gx8(H5AN8G8NAFR)*16
1Gx8(H5AN8G8NAFR)*18
1
1
1
2
2
8GB
16GB
16GB
Rev. 1.4 / Sep.2017
3
Key Parameters
CAS
Latency
(tCK)
tCK
(ns)
tRCD
(ns)
tRP
(ns)
tRAS
(ns)
tRC
(ns)
MT/s
Grade
CL-tRCD-tRP
13.75
13.75
48.75
(48.50)*
DDR4-1600
DDR4-1866
DDR4-2133
DDR4-2400
-PB
-RD
-TF
-UH
1.25
1.071
0.937
0.833
11
13
15
17
35
34
33
32
11-11-11
13-13-13
15-15-15
17-17-17
(13.50)* (13.50)*
13.92 13.92
(13.50)* (13.50)*
14.06 14.06
(13.50)* (13.50)*
14.16 14.16
(13.75)* (13.75)*
47.92
(47.50)*
47.06
(46.50)*
46.16
(45.75)*
*SK hynix DRAM devices support optional downbinning to CL15, CL13 and CL11. SPD setting is programmed to match.
Address Table
4GB(1Rx16)
8GB(1Rx8)
16GB(2Rx8)
# of Bank Groups
Bank Address BG Address
Bank Address in a BG
2
4
4
BG0
BG0~BG1
BA0~BA1
A0~A15
A0~ A9
1 KB
BG0~BG1
BA0~BA1
A0~A15
A0~ A9
1 KB
BA0~BA1
A0~A15
A0~ A9
2KB
Row Address
Column Address
Page size
Rev. 1.4 / Sep.2017
4
Pin Descriptions
Pin Name
Description
Pin Name
Description
SDRAM address bus
SDRAM bank select
SCL
SDA
A0-A16
BA0, BA1
BG0, BG1
I2C serial bus clock for SPD/TS
I2C serial bus data line for SPD/TS
I2C slave address select for SPD/TS
SDRAM parity input
SDRAM bank group select
SDRAM row address strobe
SDRAM column address strobe
SDRAM write enable
SA0-SA2
PARITY
VDD
RAS_n1
CAS_n2
WE_n3
SDRAM I/O & core power supply
SDRAM activating power supply
VPP
CS0_n, CS1_n,
CS2_n, CS3_n
Rank Select Lines
C0, C1
Chip ID lines for 3DS components
SDRAM command/address reference
supply
CKE0, CEK1
SDRAM clock enable lines
VREFCA
ODT0, ODT1
ACT_n
SDRAM on-die termination control lines
SDRAM activate
VSS
Power supply return (ground)
Serial SPD/TS positive power supply
SDRAM ALERT_n
VDDSPD
ALERT_n
DQ0-DQ63
CB0-CB7
DIMM memory data bus
DIMM ECC check bits
SDRAM data strobes
DQS0_t-DQS8_t
DQS0_c-DQS8_c
RESET_n
EVENT_n
VTT
Set SDRAMs to a Known State
(positive line of differential pair)
SDRAM data strobes
SPD signals a thermal event has
occurred
(negative line of differential pair)
SDRAM data masks/data bus inversion
(x8-based x72 DIMMs)
DM0_n-DM8_n,
DBI0_n-DBI8_n
Termination supply for the Address,
Command and Control bus
SDRAM clocks (positive line of differen-
tial pair)
CK0_t, CK1_t
CK0_c, CK1_c
NC
No connection
SDRAM clocks (negative line of differ-
ential pair)
1. RAS_n is a multiplexed function with A16.
2. CAS_n is a multiplexed function with A15.
3. WE_n is a multiplexed function with A14.
Rev. 1.4 / Sep.2017
5
Input/Output Functional Descriptions
Symbol
Type
Function
CK0_t, CK0_c,
CK1_t, CK1_c
Clock: CK_t and CK_c are differential clock inputs. All address and control input signals
are sampled on the crossing of the positive edge of CK_t and negative edge of CK_c.
Input
Clock Enable: CKE HIGH activates and CKE LOW deactivates internal clock signals and
device input buffers and output drivers. Taking CKE LOW provides Precharge Power-
Down and Self-Refresh operation (all banks idle), or Active Power-Down (row Active in
any bank). CKE is synchronous for Self-Refresh exit. After VREFCA and Internal DQ Vref
CKE0, CKE1
Input have become stable during the power on and initialization sequence, they must be
maintained during all operations (including Self-Refresh). CKE must be maintained high
throughout read and write accesses. Input buffers, excluding CK_t, CK_c, ODT and CKE,
are disabled during power-down. Input buffers, excluding CKE, are disabled during Self-
Refresh.
Chip Select: All commands are masked when CS_n is registered HIGH. CS_n provides for
Input external Rank selection on systems with multiple Ranks. CS_n is considered part of the
command code.
CS0_n, CS1_n,
CS2_n, CS3_n
Chip ID: Chip ID is only used for 3DS for 2 and 4 high stack via TSV to select each slice
of stacked component. Chip ID is considered part of the command code.
C0, C1
Input
On-Die Termination: ODT (registered HIGH) enables RTT_NOM termination resistance
internal to the DDR4 SDRAM. When enabled, ODT is only applied to each DQ, DQS_t,
DQS_c and DM_n/DBI_n, signal. The ODT pin will be ignored if MR1 is programmed to
ODT0, ODT1
Input
disable RTT_NOM.
Activation Command Input: ACT_n defines the Activation command being entered along
Input with CS_n. The input into RAS_n/A16, CAS_n/A15 and WE_n/A14 will be considered as
Row Address A16, A15, and A14.
ACT_n
Command Inputs: RAS_n/A16, CAS_n/A15 and WE_n/A14 (along with CS_n) define the
command being entered. Those pins have multi function. For example, for activation
Input with ACT_n Low, these are Addresses like A16, A15, and A14 but for non-activation
command with ACT_n High, these are Command pins for Read, Write, and other
command defined in command truth table.
RAS_n/A16,
CAS_n/A15,
WE_n/A14
Input Data Mask and Data Bus Inversion: DM_n is an input mask signal for write data.
Input data is masked when DM_n is sampled LOW coincident with that input data during
Input/ a Write access. DM_n is sampled on both edges of DQS. DM is muxed with DBI function.
Output DBI_n is an input/output identifying wherther to store/output the true or inverted data.
If DBI_n is LOW, the data will be stored/output after inversion inside the DDR4 SDRAM
and not inverted if DBI_n is HIGH.
DM_n/DBI_n
BG0-BG1
Bank Group Inputs: BG0 - BG1 define which bank group an Active, Read, Write, or
Precharge command is being applied. BG0 also determines which mode register is to be
accessed during a MRS cycle. For x4/8 based SDRAMs, BG0 and BG1 are valid. For x16
Input
based SDRAM components, only BG0 is valid.
Bank Address Inputs: BA0 - BA1 define to which bank an Active, Read, Write, or
Input Precharge command is being applied. Bank address also determines which mode
register is to be accessed during a MRS cycle.
BA0-BA1
Rev. 1.4 / Sep.2017
6
Symbol
Type
Function
Address Inputs: Provide the row address for ACTIVATE Commands and the column
address for Read/Write commands to select one location out of the memory array in the
A0 - A16
Input respective bank. A10/AP, A12/BC_n, RAS_n/A16, CAS_n/A15, and WE_n/A14 have
additional functions. See other rows. The address inputs also provide the op-code during
Mode Register Set commands.
Auto-precharge: A10 is sampled during Read/Write commands to determine whether
Autoprecharge should be performed to the accessed bank after the Read/Write
operation. (HIGH: Autoprecharge; LOW: no Autoprecharge). A10 is sampled during a
Precharge command to determine whether the Precharge applies to one bank (A10
A10 / AP
Input
LOW) or all banks (A10 HIGH). If only one bank is to be precharged, the bank is selected
by bank addresses.
Burst Chop: A12/BC_n is sampled during Read and Write commands to determine if
Input burst chop (on-the-fly) will be performed. (HIGH, no burst chop; LOW: burst chopped).
See command truth table for details.
A12 / BC_n
RESET_n
CMOS Active Low Asynchronous Reset: Reset is active when RESET_n is LOW, and inactive
Input when RESET_n is HIGH. RESET_n must be HIGH during normal operation.
Data Input/ Output: Bi-directional data bus. If CRC is enabled via Mode register then
Input/ CRC code is added at the end of Data Burst. Any DQ from DQ0-DQ3 may indicate the
Output internal Vref level during test via Mode Register Setting MR4 A4=High. Refer to vendor
specific data sheets to determine which DQ is used.
DQ
Data Strobe: output with read data, input with write data. Edge-aligned with read data,
centered in write data. DDR4 SDRAMs support differential data strobe only and does not
support single-ended.
Input/
Output
DQS_t, DQS_c,
Command and Address Parity Input : DDR4 Supports Even Parity check in DRAMs with
MR setting. Once it’s enabled via Register in MR5, then DSRAM calculates Parity with
Input ACT_n, RAS_n/A16, CAS_n/A15, WE_n/A14, BG0-BG1, BA0-BA1, A16-A0. Input parity
should be maintained at the rising edge of the clock and at the same time with
command & address with CS_n LOW.
PARITY
ALERT: It has multiple functions, such as CRC error flag or Command and Address Parity
error flag, as an Output signal. If there is an error in CRC, then ALERT_n goes LOW for
the period time interval and goes back HIGH. If there is an error in Command Address
Output Parity Check, then ALERT_n goes LOW for relatively long period until on going DRAM
internal recovery transaction is complete.
ALERT_n
During Connectivity Test mode, this pin functions as an input.
Use of this signal or not is dependent on the system.
SA0-SA1
RFU
Input Device address for the SPD.
Reserved for Future Use. No on DIMM electrical connection is present.
No Connect: No on DIMM electrical connection is present.
NC
VDD1
Supply
Supply
Supply
Power Supply: 1.2 V +/- 0.06 V
Ground
VSS
VTT2
Power Supply : 0.6V
Rev. 1.4 / Sep.2017
7
Symbol
Type
Function
Supply
Supply
Supply
DRAM Activating Power Supply: 2.5V (2.375V min , 2.75V max)
Reference voltage for CA
VPP
VREFCA
VDDSPD
Power supply used to power the I2C bus on the SPD.
Note:
1. For PC4, VDD 1.2V. For PC4L VDD is TBD.
2. For PC4, VTT is 0.6V. For PC4L VTT is TBD.
Rev. 1.4 / Sep.2017
8
Pin Assignments
Front Side
Pin
Back Side
Pin Label
Front Side
Pin Label
Back Side
Pin Label
Pin
Pin
Pin
Pin Label
1
VSS
DQ5
VSS
2
VSS
DQ4
131
133
135
137
139
141
143
A3
A1
132
134
136
138
140
142
144
A2
3
4
EVENT_
n
5
6
VSS
VDD
VDD
7
DQ1
VSS
8
DQ0
CK0_t
CK0_c
VDD
CK1_t
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
VSS
CK1_C
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
DQS0_
C
DM0_n, DBI0_n
VSS
VDD
A0
DQS0_t
VSS
PARITY
DQ6
KEY
DQ7
VSS
VSS
DQ2
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
201
BA1
VDD
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
202
A10/AP
VDD
DQ3
VSS
VSS
DQ12
VSS
CS0_n
A14/WE_n
VDD
BA0
DQ13
VSS
A16/RAS_n
VDD
DQ8
DQ9
VSS
ODT0
CS1_n
VDD
A15/CAS_n
A13
VSS
DQS1_C
DM1_n, DBI1_n
VSS
DQS1_t
VSS
VDD
ODT1
VDD
C0, CS2_n, NC
VREFCA
SA2
DQ15
VSS
DQ14
VSS
C1, CS3_n, NC
VSS
DQ10
VSS
DQ11
VSS
VSS
DQ37
VSS
DQ36
DQ21
VSS
DQ20
VSS
VSS
DQ33
VSS
DQ32
VSS
DQ17
VSS
DQ16
VSS
DQS4_
C
DM4_n, DBI4_n
VSS
DQS2_c
DQS2_t
VSS
DM2_n, DBI2_n
VSS
DQS4_t
VSS
DQ39
DQ22
VSS
DQ38
VSS
DQ23
VSS
VSS
DQ35
VSS
DQ18
DQ34
VSS
DQ19
VSS
VSS
DQ45
VSS
DQ28
VSS
DQ44
VSS
DQ29
VSS
DQ41
DQ24
VSS
DQ40
VSS
DQ25
VSS
VSS
DQS5_c
DQS5_t
VSS
DQS3_c
DQS3_t
DM5_n, DBI5_n
VSS
DM3_n, DBI3_n
Rev. 1.4 / Sep.2017
9
Front Side
Pin Label
Back Side
Pin Label
Front Side
Pin Label
Back Side
Pin Label
Pin
Pin
Pin
Pin
77
79
VSS
DQ30
VSS
78
80
VSS
DQ31
203
205
207
209
211
213
215
217
219
221
223
225
227
229
231
233
235
237
239
241
243
245
247
249
251
253
255
257
259
DQ46
VSS
204
206
208
210
212
214
216
218
220
222
224
226
228
230
232
234
236
238
240
242
244
246
248
250
252
254
256
258
260
DQ47
VSS
81
82
VSS
DQ42
VSS
DQ43
VSS
83
DQ26
VSS
84
DQ27
VSS
85
86
DQ52
VSS
DQ53
VSS
87
CB5, NC
VSS
88
CB4, NC
VSS
89
90
DQ49
VSS
DQ48
VSS
91
CB1, NC
VSS
92
CB0, NC
VSS
93
94
DQS6_
C
DM6_n, DBI6_n
VSS
95
DQS8_c
DQS8_t
VSS
96
DM8_n, DBI8_n
VSS
DQS6_t
VSS
97
98
DQ54
VSS
99
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
CB6, NC
VSS
DQ55
VSS
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
CB2, NC
VSS
DQ50
VSS
CB7, NC
VSS
DQ51
VSS
CB3, NC
VSS
DQ60
VSS
RESET_n
CKE1
VDD
DQ61
VSS
CKE0
VDD
DQ57
VSS
DQ56
VSS
BG1
ACT_n
ALERT_n
VDD
DQS7_c
DQS7_t
VSS
BG0
DM7_n, DBI7_n
VSS
VDD
A12
A11
DQ62
VSS
DQ63
VSS
A9
A7
VDD
VDD
DQ58
VSS
DQ59
VSS
A8
A5
A6
A4
SCL
SDA
VDD
VDD
VDDSPD
VPP
SA0
VTT
VPP
SA1
Rev. 1.4 / Sep.2017
10
Functional Block Diagram
4GB, 512Mx64 Module(1Rank of x16)
CK0_t, CK0_c
A[16:0], BA[1:0]
ACT_n, PARITY,BG[0]
CS0_n
ODT0
CKE0
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
DQS0_t
DQS0_c
DQ [7:0]
DQS1_t
DQS1_c
DQSL_t
DQSL_c
DQL[7:0]
DQSU_t
DQSU_c
DQU[7:0]
D0
D1
D2
D3
Serial PD
DQ [15:8]
DM0_n/DBI0_n
DM1_n/DBI1_n
DM_n/DBI_n
DM_n/DBI_n
SCL
SDA
NC
A0
A1
A2
DQS2_t
DQS2_c
DQ [23:16]
DQS3_t
DQS3_c
DQ [15:8]
DQSL_t
DQSL_c
DQL[7:0]
DQSU_t
DQSU_c
DQU[7:0]
SA0 SA1 SA2
DM2_n/DBI2_n
DM3_n/DBI3_n
DM_n/DBI_n
DM_n/DBI_n
VDDSPD
SPD
VPP
D0–D4
D0–D4
DQS4_t
DQS4_c
DQ [39:32]
DQS5_t
DQS5_c
DQ [47:40]
DQSL_t
DQSL_c
DQL[7:0]
DQSU_t
DQSU_c
DQU[7:0]
VDD
VTT
D0–D4
D0–D4
VREFCA
VSS
DM4_n/DBI4_n
DM5_n/DBI5_n
DM_n/DBI_n
DM_n/DBI_n
DQS6_t
DQS6_c
DQ [55:48]
DQSL_t
DQSL_c
DQL[7:0]
DQS7_t
DQS7_c
DQ [63:56]
DQSU_t
DQSU_c
DQU[7:0]
DM6_n/DBI6_n
DM7_n/DBI7_n
DM_n/DBI_n
DM_n/DBI_n
Note:
1. Unless otherwize noted, resistor values are 15Ω±5%.
2. ZQ resistors are 240 Ω±1%.For all other resistor values refer to the appropriate wiring diagram.
3. CK1_t, CK1_c terminated with 75Ω±5% resistor.
Rev. 1.4 / Sep.2017
11
8GB, 1Gx64 Module(1Rank of x8)
CK0_t, CK0_c
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
CS0_n
ODT0
CKE0
ZQ
VSS
VSS
VSS
VSS
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
DQS2_t
DQS2_c
DQ [23:16]
DQS_t
DQS_c
DQ [7:0]
DQS4_t
DQS4_c
DQ [39:32]
DQS_t
DQS_c
DQ [7:0]
D1
D0
D7
D6
D5
D4
D3
D2
DM2_n/DBI2_n
DM_n/DBI_n
DM4_n/DBI4_n
DM_n/DBI_n
ZQ
ZQ
ZQ
DQS0_t
DQS0_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DQS6_t
DQS6_c
DQ [55:48]
DQS_t
DQS_c
DQ [7:0]
DM0_n/DBI0_n
DM_n/DBI_n
DM6_n/DBI6_n
DM_n/DBI_n
DQS1_t
DQS1_c
DQ [15:8]
DQS_t
DQS_c
DQ [7:0]
DQS7_t
DQS7_c
DQ [63:56]
DQS_t
DQS_c
DQ [7:0]
DM1_n/DBI1_n
DM_n/DBI_n
DM7_n/DBI7_n
DM_n/DBI_n
DQS3_t
DQS3_c
DQ [31:24]
DQS_t
DQS_c
DQ [7:0]
DQS5_t
DQS5_c
DQ [47:40]
DQS_t
DQS_c
DQ [7:0]
DM3_n/DBI3_n
DM_n/DBI_n
DM5_n/DBI5_n
DM_n/DBI_n
Serial PD
VDDSPD
SPD
SCL
EVENT_n
VPP
D0–D7
D0–D7
SDA
R1
NC
A0
A1
A2
VDD
VTT
SA2 (pin 166)
VSS
SA0 SA1
D0–D7
D0–D7
VREFCA
R2
VSS
Note:
1. Unless otherwize noted, resistor values are 15Ω±5%.
2. ZQ resistors are 240 Ω±1%.For all other resistor values refer to the appropriate wiring diagram.
3. To connect the SPD A2 input to the edge connector pin 166 install R1. To tie the SPD input A2 to ground install R2.
Do not install both R1 and R2. The values for R1 and R2 are not critical. Any value less than 100 Ohms may be used.
Rev. 1.4 / Sep.2017
12
8GB, 1Gx72 Module(1Rank of x8)
CK1_t, CK1_c
CK0_t, CK0_c
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
CS0_n
ODT0
CKE0
CS0_n
ODT0
CKE0
ZQ
VSS
VSS
VSS
VSS
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
DQS8_t
DQS8_c
CB[7:0]
DQS_t
DQS_c
DQ [7:0]
DQS2_t
DQS2_c
DQ [23:16]
DQS_t
DQS_c
DQ [7:0]
D6
D5
D4
D3
D1
D0
D8
D7
DM8_n/DBI8_n
DM_n/DBI_n
DM2_n/DBI2_n
DM_n/DBI_n
ZQ
ZQ
ZQ
DQS4_t
DQS4_c
DQ [39:32]
DQS_t
DQS_c
DQ [7:0]
DQS0_t
DQS0_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM4_n/DBI4_n
DM_n/DBI_n
DM0_n/DBI0_n
DM_n/DBI_n
DQS6_t
DQS6_c
DQ [55:48]
DQS_t
DQS_c
DQ [7:0]
DQS1_t
DQS1_c
DQ [15:8]
DQS_t
DQS_c
DQ [7:0]
DM6_n/DBI6_n
DM_n/DBI_n
DM1_n/DBI1_n
DM_n/DBI_n
DQS7_t
DQS7_c
DQ [63:56]
DQS_t
DQS_c
DQ [7:0]
DQS3_t
DQS3_c
DQ [31:24]
DQS_t
DQS_c
DQ [7:0]
DM7_n/DBI7_n
DM_n/DBI_n
DM3_n/DBI3_n
DM_n/DBI_n
ZQ
VSS
DQS5_t
DQS5_c
DQ [47:40]
DQS_t
DQS_c
DQ [7:0]
D2
DM5_n/DBI5_n
DM_n/DBI_n
Serial PD with Thermal sensor
EVENT_n/NC
VDDSPD
SPD
VPP
D0–D8
D0–D8
SCL
VDD
VTT
SDA
EVENT_n
A0
A1
A2
R1
D0–D8
D0–D8
VREFCA
pin 166
VSS
SA0 SA1
VSS
R2
Note:
1. Unless otherwize noted, resistor values are 15Ω±5%.
2. ZQ resistors are 240 Ω±1%.For all other resistor values refer to the appropriate wiring diagram.
3. To connect the SPD A2 input to the edge connector pin 166 install R1. To tie the SPD input A2 to ground install R2.
Do not install both R1 and R2. The values for R1 and R2 are not critical. Any value less than 100 Ohms may be used.
Rev. 1.4 / Sep.2017
13
16GB, 2Gx64 Module(2Rank of x8) - page1
CK0_t, CK0_c
CK1_t, CK1_c
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
CS0_n
ODT0
CKE0
CS1_n
ODT1
CKE1
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
DQS2_t
DQS2_c
DQ [23:16]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D5
D4
D0
D1
D14
D15
D11
D10
DM2_n/DBI2_n
DM_n/DBI_n
DM_n/DBI_n
DQS0_t
DQS0_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM0_n/DBI0_n
DM_n/DBI_n
DM_n/DBI_n
DQS1_t
DQS1_c
DQ [15:8]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM1_n/DBI1_n
DM_n/DBI_n
DM_n/DBI_n
DQS3_t
DQS3_c
DQ [31:24]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM3_n/DBI3_n
DM_n/DBI_n
DM_n/DBI_n
Rev. 1.4 / Sep.2017
14
16GB, 2Gx64 Module(2Rank of x8) - page2
CK0_t, CK0_c
CK1_t, CK1_c
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
A[16:0], BA[1:0]
ACT_n, PARITY,BG[1:0]
CS0_n
ODT0
CKE0
CS1_n
ODT1
CKE1
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
DQS4_t
DQS4_c
DQ [39:32]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D2
D3
D7
D6
D9
DM4_n/DBI4_n
DM_n/DBI_n
DM_n/DBI_n
DQS6_t
DQS6_c
DQ [55:48]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D8
DM6_n/DBI6_n
DM_n/DBI_n
DM_n/DBI_n
DQS7_t
DQS7_c
DQ [63:56]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D12
D13
DM7_n/DBI7_n
DM_n/DBI_n
DM_n/DBI_n
DQS5_t
DQS5_c
DQ [47:40]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM5_n/DBI5_n
DM_n/DBI_n
DM_n/DBI_n
Serial PD
VDDSPD
VPP
SPD
SCL
SDA
D0–D15
D0–D15
A0
A1
A2
VDD
VTT
SA0 SA1 SA2
D0–D15
D0–D15
VREFCA
VSS
Note:
1. Unless otherwize noted, resistor values are 15Ω±5%.
2. ZQ resistors are 240 Ω±1%.For all other resistor values refer to the appropriate wiring diagram.
3. SDRAMs for ODD ranks (D8 to D15), which are placed on the back side of the module use the address mirroing for A4-A3, A6-A5, A8-A7,
A13-A11, BA1-BA0 and BG1-BG0. More detail can be found in the DDR4 SODIMM Common Section of the Design Specification.
Rev. 1.4 / Sep.2017
15
16GB, 2Gx72 Module(2Rank of x8)
CK0_t, CK0_c
CK1_t, CK1_c
PARITY
A[16:0],BA[1:0],BG[1:0],ACT_n
CS0_n
CS1_n
ODT1
CKE1
ODT0
CKE0
DQS0_t
DQS0_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D1
D2
D0
D3
D5
D8
D6
D7
D4
D10
D11
D9
DM0_n/DBI0_n
DM_n/DBI_n
DM_n/DBI_n
ZQ
ZQ
ZQ
VSS
VSS
VSS
ZQ
ZQ
ZQ
VSS
VSS
VSS
DQS1_t
DQS1_c
DQ [15:8]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM1_n/DBI1_n
DM_n/DBI_n
DM_n/DBI_n
DQS2_t
DQS2_c
DQ [23:16]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM2_n/DBI2_n
DM_n/DBI_n
DM_n/DBI_n
DQS3_t
DQS3_c
DQ [31:24]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D12
D14
D17
D15
D16
D13
DM3_n/DBI3_n
DM_n/DBI_n
DM_n/DBI_n
ZQ
ZQ
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
VSS
VSS
ZQ
ZQ
ZQ
ZQ
ZQ
ZQ
VSS
VSS
VSS
VSS
VSS
DQS4_t
DQS4_c
DQ [39:32]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM4_n/DBI4_n
DM_n/DBI_n
DM_n/DBI_n
DQS5_t
DQS5_c
DQ [47:40]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
VDDSPD
VPP
SPD
DM5_n/DBI5_n
DM_n/DBI_n
DM_n/DBI_n
D0–D17
D0–D17
VDD
VTT
DQS6_t
DQS6_c
DQ [55:48]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
D0–D17
D0–D17
VREFCA
VSS
DM6_n/DBI6_n
DM_n/DBI_n
DM_n/DBI_n
DQS7_t
DQS7_c
DQ [63:56]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
DM7_n/DBI7_n
DM_n/DBI_n
DM_n/DBI_n
Serial PD with Thermal sensor
SCL
DQS8_t
DQS8_c
CB [7:0]
DQS_t
DQS_c
DQ [7:0]
DQS_t
DQS_c
DQ [7:0]
SDA
EVENT_n
VSS
EVENT_n
A0 A1
A2
DM8_n/DBI8_n
DM_n/DBI_n
DM_n/DBI_n
SA0 SA1 SA2
Note:
1. DQ-to-I/O wiring is shown as recommended but may be changed.
2. Unless otherwize noted, resistor values are 15Ω±5%.
3. See the Net Structure diagrams for all resistors associated with the command, address and control bus.
4. ZQ resistors are 240 Ω±1%.For all other resistor values refer to the appropriate wiring diagram.
Rev. 1.4 / Sep.2017
16
Absolute Maximum Ratings
Absolute Maximum DC Ratings
Absolute Maximum DC Ratings
Symbol
Parameter
Rating
Units
NOTE
VDD
-0.3 ~ 1.5
-0.3 ~ 1.5
-0.3 ~ 3.0
-0.3 ~ 1.5
-55 to +100
V
1,3
Voltage on VDD pin relative to Vss
Voltage on VDDQ pin relative to Vss
Voltage on VPP pin relative to Vss
Voltage on any pin except VREFCA relative to Vss
Storage Temperature
VDDQ
VPP
V
V
1,3
4
VIN, VOUT
TSTG
V
1,3,5
1,2
°C
NOTE :
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at these or any other conditions above those indi-
cated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect reliability
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement
conditions, please refer to JESD51-2 standard.
3. VDD and VDDQ must be within 300 mV of each other at all times;and VREFCA must be not greater than 0.6 x
VDDQ, When VDD and VDDQ are less than 500 mV; VREFCA may be equal to or less than 300 mV
4. VPP must be equal or greater than VDD/VDDQ at all times
5. Overshoot area above 1.5V is specified in DDR4 Device Operation.
DRAM Component Operating Temperature Range
Temperature Range
Symbol
Parameter
Rating
Units
oC
oC
Notes
0 to 85
1,2
Normal Operating Temperature Range
Extended Temperature Range
TOPER
85 to 95
1,3
NOTE:
1. Operating Temperature TOPER is the case surface temperature on the center / top side of the DRAM. For measure-
ment conditions, please refer to the JEDEC document JESD51-2.
2. The Normal Temperature Range specifies the temperatures where all DRAM specifications will be supported.
During operation, the DRAM case temperature must be maintained between 0 - 85oC under all operating condi-
tions.
3. Some applications require operation of the DRAM in the Extended Temperature Range between 85oC and 95oC
case temperature. Full specifications are guaranteed in this range, but the following additional conditions apply:
a. Refresh commands must be doubled in frequency, therefore reducing the Refresh interval tREFI to 3.9 µs. It is
also possible to specify a component with 1X refresh (tREFI to 7.8µs) in the Extended Temperature Range.
Please refer to the DIMM SPD for option availability
b. If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use
the Manual Self-Refresh mode with Extended Temperature Range capability (MR2 A6 = 0b and MR2 A7 = 1b)
or enable the optional Auto Self-Refresh mode (MR2 A6 = 1b and MR2 A7 = 0b).
Rev. 1.4 / Sep.2017
17
AC & DC Operating Conditions
Recommended DC Operating Conditions
Recommended DC Operating Conditions
Rating
Typ.
1.2
Symbol
Parameter
Unit
NOTE
Min.
1.14
1.14
Max.
1.26
VDD
VDDQ
VPP
Supply Voltage
V
V
V
1,2,3
1,2,3
3
Supply Voltage for Output
1.2
1.26
2.75
Supply Voltage for DRAM Activating 2.375
2.5
NOTE:
1. Under all conditions VDDQ must be less than or equal to VDD.
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.
3. DC bandwidth is limited to 20MHz.
Rev. 1.4 / Sep.2017
18
AC & DC Input Measurement Levels
AC & DC Logic input levels for single-ended signals
Single-ended AC & DC input levels for Command and Address
DDR4-1600/1866/2133/
DDR4-2666/3200
2400
Symbol
Parameter
Unit NOTE
Min.
Max.
Min.
Max.
VREFCA
0.075
+
VIH.CA(DC75)
VIL.CA(DC75)
DC input logic high
DC input logic low
VDD
TBD
TBD
V
V
VREFCA
0.075
-
VSS
TBD
TBD
VIH.CA(AC100)
VIL.CA(AC100)
VREF + 0.1
Note 2
AC input logic high
AC input logic low
Note 2
TBD
TBD
TBD
TBD
V
V
1
1
VREF - 0.1
Reference Voltage for
ADD, CMD inputs
VREFCA(DC)
0.49*VDD
0.51*VDD
TBD
TBD
V
2,3
NOTE :
1. See “Overshoot and Undershoot Specifications”
2. The AC peak noise on VREFCA may not allow VREFCA to deviate from VREFCA(DC) by more than ± 1% VDD (for
reference : approx. ± 12mV)
3. For reference : approx. VDD/2 ± 12mV
Rev. 1.4 / Sep.2017
19
AC and DC Input Measurement Levels: V
Tolerances
REF
The DC-tolerance limits and ac-noise limits for the reference voltages V
is illustrated in Figure below.
REFCA
It shows a valid reference voltage V (t) as a function of time. (V
stands for V
).
REF
REF
REFCA
V
(DC) is the linear average of V
(t) over a very long period of time (e.g. 1 sec). This average has to
REF
REF
meet the min/max requirement in Table X. Furthermore V
(t) may temporarily deviate from V
(DC) by
REF
REF
no more than ± 1% V
.
DD
voltage
VDD
VSS
time
Illustration of V
(DC) tolerance and V
AC-noise limits
REF
REF
The voltage levels for setup and hold time measurements V (AC), V (DC), V (AC) and V (DC) are
IH
IH
IL
IL
dependent on V
.
REF
"V " shall be understood as V (DC), as defined in Figure above.
REF
REF
This clarifies, that DC-variations of V
affect the absolute voltage a signal has to reach to achieve a valid
REF
high or low level and therefore the time to which setup and hold is measured. System timing and voltage
budgets need to account for V (DC) deviations from the optimum position within the data-eye of the
REF
input signals.
This also clarifies that the DRAM setup/hold specification and derating values need to include time and
voltage associated with V
AC-noise. Timing and voltage effects due to AC-noise on V
up to the spec-
REF
REF
ified limit (+/-1% of V ) are included in DRAM timings and their associated deratings.
DD
Rev. 1.4 / Sep.2017
20
AC and DC Logic Input Levels for Differential Signals
Differential signal definition
tDVAC
VIH.DIFF.AC.MIN
VIH.DIFF.MIN
0.0
half cycle
VIL.DIFF.MAX
VIL.DIFF.AC.MAX
tDVAC
time
NOTE:
1. Differential signal rising edge from VIL.DIFF.MAX to VIH.DIFF.MIN must be monotonic slope.
2. Differential signal falling edge from VIH.DIFF.MIN to VIL.DIFF.MAX must be monotonic slope.
Definition of differential ac-swing and “time above ac-level” t
DVAC
Rev. 1.4 / Sep.2017
21
Differential swing requirements for clock (CK_t - CK_c)
Differential AC and DC Input Levels
DDR4 -1600,1866,2133
DDR4 -2400,2666 & 3200
Symbol
Parameter
unit NOTE
min
+0.150
max
NOTE 3
-0.150
min
TBD
max
NOTE 3
TBD
VIHdiff
VILdiff
differential input high
differential input low
V
V
1
1
NOTE 3
NOTE 3
2 x (VIH(AC) -
2 x (VIH(AC) -
V
IHdiff(AC)
differential input high ac
ILdiff(AC)
differential input low ac
NOTE 3
NOTE 3
V
V
2
2
VREF
)
VREF
)
2 x (VIL(AC) -
2 x (VIL(AC) -
V
NOTE 3
NOTE 3
VREF
)
VREF)
NOTE :
1. Used to define a differential signal slew-rate.
2. for CK_t - CK_c use VIH.CA/VIL.CA(AC) of ADD/CMD and VREFCA
;
3. These values are not defined; however, the differential signals CK_t - CK_c, need to be within the respective limits
(VIH.CA(DC) max, VIL.CA(DC)min) for single-ended signals as well as the limitations for overshoot and undershoot.
Allowed time before ringback (tDVAC) for CK_t - CK_c
tDVAC [ps] @ |VIH/Ldiff(AC)| = 200mV tDVAC [ps] @ |VIH/Ldiff(AC)| = TBDmV
Slew Rate [V/ns]
min
120
115
110
105
100
95
max
min
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
max
> 4.0
4.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.0
2.0
1.8
1.6
1.4
90
1.2
85
1.0
80
< 1.0
80
Rev. 1.4 / Sep.2017
22
Single-ended requirements for differential signals
Each individual component of a differential signal (CK_t, CK_c) has also to comply with certain require-
ments for single-ended signals.
CK_t and CK_c have to approximately reach VSEHmin / VSELmax (approximately equal to the ac-levels
(VIH.CA(AC) / VIL.CA(AC) ) for ADD/CMD signals) in every half-cycle.
Note that the applicable ac-levels for ADD/CMD might be different per speed-bin etc. E.g., if Different
value than VIH.CA(AC100)/VIL.CA(AC100) is used for ADD/CMD signals, then these ac-levels apply also for
the single-ended signals CK_t and CK_c
VDD or VDDQ
VSEH min
VSEH
VDD/2 or VDDQ/2
CK
VSEL max
VSEL
VSS or VSSQ
time
Single-ended requirement for differential signals
Note that, while ADD/CMD signal requirements are with respect to VrefCA, the single-ended components
of differential signals have a requirement with respect to VDD / 2; this is nominally the same. The transi-
tion of single-ended signals through the ac-levels is used to measure setup time. For single-ended compo-
nents of differential signals the requirement to reach VSELmax, VSEHmin has no bearing on timing, but
adds a restriction on the common mode characteristics of these signals.
Rev. 1.4 / Sep.2017
23
Single-ended levels for CK_t, CK_c
DDR4-1600/1866/2133 DDR4-2400/2666/3200
Symbol
VSEH
Parameter
Unit NOTE
Min
Max
Min
Max
Single-ended high-level for
CK_t , CK_c
Single-ended low-level for
CK_t , CK_c
(VDD/2)
+0.100
NOTE3
TBD
NOTE3
V
V
1, 2
1, 2
(VDD/2)-
0.100
VSEL
NOTE3
NOTE3
TBD
NOTE :
1. For CK_t - CK_c use VIH.CA/VIL.CA(AC) of ADD/CMD;
2. VIH(AC)/VIL(AC) for ADD/CMD is based on VREFCA
;
3. These values are not defined, however the single-ended signals CK_t - CK_c need to be within the respective limits
(VIH.CA(DC) max, VIL.CA(DC)min) for single-ended signals as well as the limitations for overshoot and undershoot.
Rev. 1.4 / Sep.2017
24
Address and Control Overshoot and Undershoot specifications
AC overshoot/undershoot specification for Address, Command and Control pins
Specification
Parameter
Unit
DDR4-
1600
DDR4-
1866
DDR4-
2133
DDR4-
2400
DDR4-
2666
Maximum peak amplitude above VDD Absolute Max
allowed for overshoot area
0.06
0.06
0.06
0.06
TBD
V
Delta value between VDD Absolute Max and VDD Max
allowed for overshoot area
0.24
0.3
0.24
0.3
0.24
0.3
0.24
0.3
TBD
TBD
TBD
V
Maximum peak amplitude allowed for undershoot area
V-ns
V-ns
Maximum overshoot area per 1tCK Above Absolute
Max
0.0083
0.0071
0.0062
0.0055
Maximum overshoot area per 1tCK Between Absolute
Max
0.2550
0.2644
0.2185
0.2265
0.1914
0.1984
0.1699
0.1762
TBD
TBD
V-ns
V-ns
Maximum undershoot area per 1tCK Below VSS
(A0-A13,A17,BG0-BG1,BA0-BA1,ACT_n,RAS_n/A16,CAS_n/A15,WE_n/A14,CS_n,CKE,ODT,C2-C0)
Overshoot Area above VDD Absolute Max
VDD Absolute Max
Overshoot Area Between
VDD Absolute Max and VDD Max
VDD
VSS
Volts
(V)
1 tCK
Undershoot Area below VSS
Address,Command and Control Overshoot and Undershoot Definition
Rev. 1.4 / Sep.2017
25
Clock Overshoot and Undershoot Specifications
AC overshoot/undershoot specification for Clock
Specification
Parameter
Unit
DDR4-
1600
DDR4-
1866
DDR4-
2133
DDR4-
2400
DDR4-
2666
Maximum peak amplitude above VDD Absolute Max
allowed for overshoot area
0.06
0.06
0.24
0.06
0.24
0.06
0.24
TBD
TBD
V
V
Delta value between VDD Absolute Max and VDD Max
allowed for overshoot area
0.24
0.3
Maximum peak amplitude allowed for undershoot area
0.3
0.3
0.3
TBD
TBD
V
Maximum overshoot area per 1UI Above Absolute Max 0.0038
0.0032
0.0028
0.0025
V-ns
Maximum overshoot area per 1UI Between Absolute
Max
0.1125
0.0964
0.0980
0.0844
0.0858
0.0750
0.0762
TBD
TBD
V-ns
V-ns
Maximum undershoot area per 1UI Below VSS
0.1144
(CK_t, Ck_c)
Overshoot Area above VDD Absolute Max
Overshoot Area Between
VDD Absolute Max
VDD Absolute Max and VDD Max
VDD
Volts
(V)
1 UI
VSS
Undershoot Area below VSS
Clock Overshoot and Undershoot Definition
Rev. 1.4 / Sep.2017
26
Data, Strobe and Mask Overshoot and Undershoot Specifications
AC overshoot/undershoot specification for Data, Strobe and Mask
Specification
Parameter
Unit
DDR4-
1600
DDR4-
1866
DDR4-
2133
DDR4-
2400
DDR4-
2666
Maximum peak amplitude above Max absolute level of
Vin,Vout
0.16
0.24
0.16
0.24
0.16
0.24
0.16
0.24
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
V
V
Overshoot area Between Max Absolute level of Vin,
Vout and VDDQ Max
Undershoot area Between Min absolute level of
Vin,Vout and VDDQ Max
0.30
0.30
0.30
0.30
V
Maximum peak amplitude below Min absolute level of
Vin,Vout
0.10
0.10
0.10
0.10
V
Maximum overshoot area per 1UI Above Max absolute
level of Vin,Vout
0.0150
0.1050
0.1050
0.0150
0.0129
0.0900
0.0900
0.0129
0.0113
0.0788
0.0788
0.0113
0.0100
0.0700
0.0700
0.0100
V-ns
V-ns
V-ns
V-ns
Maximum overshoot area per 1UI Between Max abso-
lute level of Vin,Vout and VDDQ Max
Maximum undershoot area per 1UI Between Min abso-
lute level of Vin,Vout and VSSQ
Maximum undershoot area per 1UI Below Min abso-
lute level of Vin,Vout
(DQ,DQS_t,DQS_c,DM_n, DBI_n, TDQS_t, TDQS_c)
Overshoot Area above Max absolute level of Vin,Vout
Max absolute level of Vin,Vout
Overshoot Area Between
Max absolute level of Vin,Vout and VDDQ
VDDQ
VSSQ
Volts
(V)
1 UI
Undershoot Area Between
Min absolute level of Vin,Vout and VSSQ
Min absolute level of Vin,Vout
Undershoot Area below Min absolute level of Vin, Vout
Data, Strobe and Mask Overshoot and Undershoot Definition
Rev. 1.4 / Sep.2017
27
Slew Rate Definitions
Slew Rate Definitions for Differential Input Signals (CK)
Input slew rate for differential signals (CK_t, CK_c) are defined and measured as shown in Table and Fig-
ure below.
Differential Input Slew Rate Definition
Description
Defined by
from
to
V
V
V
V
V
V
V
Differential input slew rate for rising edge(CK_t - CK_c)
Differential input slew rate for falling edge(CK_t - CK_c)
[
[
ILdiffmax ] / DeltaTRdiff
ILdiffmax
IHdiffmin
IHdiffmin -
V
ILdiffmax ] / DeltaTFdiff
IHdiffmin
ILdiffmax
IHdiffmin -
NOTE: The differential signal (i,e.,CK_t - CK_c) must be linear between these thresholds.
Delta TRdiff
V
IHdiffmin
0
V
ILdiffmax
Delta TFdiff
Differential Input Slew Rate Definition for CK_t, CK_c
Rev. 1.4 / Sep.2017
28
Slew Rate Definition for Single-ended Input Signals (CMD/ADD)
Delta TRsingle
V
IHCA(AC) Min
V
IHCA(DC) Min
VREFCA(DC)
V
ILCA(DC) Max
V
ILCA(AC) Max
Delta TFsingle
Single-ended Input Slew Rate definition for CMD and ADD
NOTE :
1. Single-ended input slew rate for rising edge = { VIHCA(AC)Min - VILCA(DC)Max } / Delta TR single
2. Single-ended input slew rate for falling edge = { VIHCA(DC)Min - VILCA(AC)Max } / Delta TF single
3. Single-ended signal rising edge from VILCA(DC)Max to VIHCA(DC)Min must be monotonic slope.
4. Single-ended signal falling edge from VIHCA(DC)Min to VILCA(DC)Max must be monotonic slope
Rev. 1.4 / Sep.2017
29
Differential Input Cross Point Voltage
To guarantee tight setup and hold times as well as output skew parameters with respect to clock, each
cross point voltage of differential input signals (CK_t, CK_c) must meet the requirements in Table. The dif-
ferential input cross point voltage VIX is measured from the actual cross point of true and complement sig-
nals to the midlevel between of VDD and VSS.
VDD
CK_t
Vix
VDD/2
Vix
CK_c
VSEL
VSEH
VSS
Vix Definition (CK)
Cross point voltage for differential input signals (CK)
DDR4-1600/1866/2133
Symbol
Parameter
min
max
VDD/2 - 145mV VDD/2 + 100mV
VSEL =<
VDD/2 - 145mV
VDD/2 + 145mV
=< VSEH
-
Area of VSEH, VSEL
=< VSEL =<
=< VSEH =<
VDD/2 - 100mV VDD/2 + 145mV
Differential Input Cross Point
VlX(CK) Voltage relative to VDD/2 for
CK_t, CK_c
- (VDD/2 - VSEL) (VSEH - VDD/2)
-120mV
120mV
+ 25mV
- 25mV
DDR4-2400/2666/3200
Symbol
Parameter
min
max
-
Area of VSEH, VSEL
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Differential Input Cross Point
VlX(CK) Voltage relative to VDD/2 for
CK_t, CK_c
Rev. 1.4 / Sep.2017
30
CMOS rail to rail Input Levels
CMOS rail to rail Input Levels for RESET_n
CMOS rail to rail Input Levels for RESET_n
Parameter
Symbol
Min
0.8*VDD
0.7*VDD
VSS
Max
VDD
Unit
V
NOTE
AC Input High Voltage
DC Input High Voltage
DC Input Low Voltage
AC Input Low Voltage
Rising time
VIH(AC)_RESET
VIH(DC)_RESET
VIL(DC)_RESET
VIL(AC)_RESET
TR_RESET
6
2
VDD
V
0.3*VDD
0.2*VDD
1.0
V
1
VSS
V
7
-
us
us
4
RESET pulse width
tPW_RESET
1.0
-
3,5
NOTE :
1. After RESET_n is registered LOW, RESET_n level shall be maintained below VIL(DC)_RESET during tPW_RESET,
otherwise, SDRAM may not be reset.
2. Once RESET_n is registered HIGH, RESET_n level must be maintained above VIH(DC)_RESET, otherwise, SDRAM
operation will not be guaranteed until it is reset asserting RESET_n signal LOW.
3. RESET is destructive to data contents.
4. No slope reversal(ringback) requirement during its level transition from Low to High.
5. This definition is applied only “Reset Procedure at Power Stable”.
6. Overshoot might occur. It should be limited by the Absolute Maximum DC Ratings.
7. Undershoot might occur. It should be limited by Absolute Maximum DC Ratings
tPW_RESET
0.8*VDD
0.7*VDD
0.3*VDD
0.2*VDD
TR_RESET
RESET_n Input Slew Rate Definition
Rev. 1.4 / Sep.2017
31
AC and DC Logic Input Levels for DQS Signals
Differential signal definition
Definition of differential DQS Signal AC-swing Level
Differential swing requirements for DQS (DQS_t - DQS_c)
Differential AC and DC Input Levels for DQS
DDR4-1600,1866,2133
DDR4-2400
DDR4-2666,3200
Symbol
Parameter
Unit Note
Min
186
Max
Note2
-186
Min
Max
TBD
TBD
Min
TBD
TBD
Max
TBD
TBD
VIHDiffPeak VIH.DIFF.PeakVoltage
VILDiffPeak VIL.DIFF.Peak Voltage
TBD
TBD
mV
mV
1
1
Note2
NOTE :
1. Used to define a differential signal slew-rate.
2. These values are not defined; however, the differential signals DQS_t - DQS_c, need to be within the respective
limits Overshoot, Undershoot Specification for single-ended signals.
Rev. 1.4 / Sep.2017
32
Peak voltage calculation method
The peak voltage of Differential DQS signals are calculated in a following equation.
VIH.DIFF.Peak Voltage = Max(f(t))
VIL.DIFF.Peak Voltage = Min(f(t))
f(t) = VDQS_t - VDQS_c
The Max(f(t)) or Min(f(t)) used t o determine the midpoint which to reference the +/-35% window of the
exempt non-monotonic signaling shall be the samllest peak voltage observed in all ui’s.
Definition of differential DQS Peak Voltage and rage of exempt non-monotonic signaling
Rev. 1.4 / Sep.2017
33
Differential Input Cross Point Voltage
To achieve tight RxMask input requirements as well as output skew parameters with respect to strobe, the
cross point voltage of differential input signals (DQS_t, DQS_c) must meet the requirements in Tabel
below. The differential input cross point voltage VIX_DQS (VIX_DQS_FR and VIX_DQS_RF) ins measured
from the actual cross point of DQS_t, DQS_c relative to the VDQSmid fo the DQS_t and DQS_c signals.
VDQSmid is the midpoint of the minimum levels achieved by the transitioning DQS_t and DQS_c signals,
and noted by VDQS_trans. VDQS_trans is the difference between the lowest horizontal tangent above
VDQSmid of the transitioning DQS signals and the highest horizontal tangent below VDQSmid of the tran-
sitioning DQS signals.
A non-monotonic transitioning signal’s ledge is exempt or not used in determination of a horizontal tangent
provieded the said ledge occurs within +/- 30% of the midpoint of either VID.DIFF.Peak Voltage (DQS_t
rising) of VIL.DIFF.Peak Voltage (DQS_c rising), refer to Furure Definition of differential DQS Peak Voltage
and rage of exempt non-monotonic signaling. A secondary horizontal tangent resulting from a ring-back
transition is also exempt in determination of a horizontal tangent. Thath is, a falling transition’s horizontal
tangent is derived from its negative slope to zero slope transition (point A in Fugure bloew) and a ring-
back’s horizontal tangent derived from its positive slope to zero slope transition (point B in Figure below) is
not a valid horizontal tangent; and a rising transition’s horizontal tangent is derived from its positive slope
to zero slope transition (point C in Figure below) and a ring-back’s horizontal tangent derived from its neg-
ative slope to zero slope transition (point D in Figure below) is not a valid horizontal tangent.
Vix Definition (DQS)
Rev. 1.4 / Sep.2017
34
Cross point voltage for differential input signals
DDR4-
1600,1866,2133,2400
DDR4-
2666,2933,3200
Symbol
Parameter
Unit Note
Min
Max
Min
Max
DQS_t and DQS_c crossing relative
to the midpoint of the DQS_t and
DQS_c signal swings
Vix_DOS_
ratio
-
25
TBD
25
%
1,2
NOTE :
1. Vix_DQS_Ratio is DQS VIX crossing (Vix_DQS_FR or Vix_DQS_RF) divided by VDQS_trans. VDQS_trans is the
difference between the lowest horizontal tangent above VDQSmid of the transitioning DQS signals and the highest
horizontal tangent below VDQSmid of the transitioning DQS signals.
2. VDQSmid will be similar to the VREFDQ internal setting value obtained during Vref Training if the DQS and DQs
drivers and paths are matched.
Rev. 1.4 / Sep.2017
35
Differential Input Slew Rate Definition
Input slew rate for differential signals (DQS_t, DQS_c) are defined and measured as shown in Figure
below.
NOTE :
1. Differential signal rising edge from VILDiff_DQS to VIHDiff_DQS must be monotonic slope.
2. Differential signal falling edge from VIHDiff_DQS to VILDiff_DQS must be monotonic slope.
Differential Input Slew Rate Definition for DQS_t, DQS_c
Differential Input Slew Rate Definition for DQS_t, DQS_c
Description
Defined by
From
To
Differential input slew rate for
rising edge(DQS_t - DQS_c)
VILDiff_DQS
VIHDiff_DQS
|VILDiff_DQS - VIHDiff_DQS|/DeltaTRdiff
|VILDiff_DQS - VIHDiff_DQS|/DeltaTFdiff
Differential input slew rate for
falling edge(DQS_t - DQS_c)
VIHDiff_DQS
VILDiff_DQS
Differential Input Level for DQS_t, DQS_c
DDR4-1600,1866,2133
DDR4-2400
DDR4-2666,3200
Symbol
Parameter
Unit Note
Min
136
-
Max
-
Min
Max
-
Min
TBD
TBD
Max
TBD
TBD
VIHDiff_DQS Differential Input High
VILDiff_DQS Differential Input Low
130
-
mV
mV
-136
-130
Rev. 1.4 / Sep.2017
36
Differential Input Slew Rate for DQS_t, DQS_c
DDR4-1600,1866,2133
DDR4-2400
DDR4-2666,3200
Symbol
SRIdiff
Parameter
Unit Note
Min
Max
Min
Max
Min
Max
Differential Input
Slew Rate
3
18
3
18
TBD
TBD
V/ns
Rev. 1.4 / Sep.2017
37
AC and DC output Measurement levels
Single-ended AC & DC Output Levels
Single-ended AC & DC output levels
DDR4-1600/1866/2133/
2400/2666/3200
Symbol Parameter
Units NOTE
V
OH(DC) DC output high measurement level (for IV curve linearity)
OM(DC) DC output mid measurement level (for IV curve linearity)
VOL(DC) DC output low measurement level (for IV curve linearity)
OH(AC) AC output high measurement level (for output SR)
1.1 x VDDQ
0.8 x VDDQ
V
V
V
V
0.5 x VDDQ
V
(0.7 + 0.15) x VDDQ
(0.7 - 0.15) x VDDQ
V
V
1
1
VOL(AC) AC output low measurement level (for output SR)
NOTE :
1. The swing of ± 0.15 × VDDQ is based on approximately 50% of the static single-ended output peak-to-peak swing
with a driver impedance of RZQ/7Ω and an effective test load of 50Ω to VTT = VDDQ
.
Differential AC & DC Output Levels
Differential AC & DC output levels
DDR4-1600/1866/
2133/2400/2666/3200
Symbol Parameter
Units NOTE
V
OHdiff(AC) AC differential output high measurement level (for output SR)
OLdiff(AC) AC differential output low measurement level (for output SR)
NOTE :
+0.3 x VDDQ
-0.3 x VDDQ
V
V
1
1
V
1. The swing of ± 0.3 × VDDQ is based on approximately 50% of the static differential output peak-to-peak swing with
a driver impedance of RZQ/7Ω and an effective test load of 50Ω to VTT = VDDQ at each of the differential outputs.
Rev. 1.4 / Sep.2017
38
Single-ended Output Slew Rate
With the reference load for timing measurements, output slew rate for falling and rising edges is defined
and measured between V
and V
for single ended signals as shown in Table and Figure below.
OL(AC)
OH(AC)
Single-ended output slew rate definition
Measured
Description
Defined by
From
To
[VOH(AC)-VOL(AC)] /
Delta TRse
VOL(AC)
VOH(AC)
Single ended output slew rate for rising edge
[VOH(AC)-VOL(AC)] /
Delta TFse
VOH(AC)
VOL(AC)
Single ended output slew rate for falling edge
NOTE :
1. Output slew rate is verified by design and characterization, and may not be subject to production test.
V
OH(AC)
V
OL(AC)
delta TFse
delta TRse
Single-ended Output Slew Rate Definition
Single-ended output slew rate
DDR4-1600 DDR4-1866 DDR4-2133 DDR4-2400 DDR4-2666 DDR4-2933 DDR4-3200
Min Max Min Max Min Max Min Max Min Max Min Max Min Max
Parameter
Symbol
Units
Single ended output slew rate SRQse
4
9
4
9
4
9
4
9
4
9
4
9
4
9
V/ns
Description: SR: Slew Rate
Q: Query Output (like in DQ, which stands for Data-in, Query-Output)
se: Single-ended Signals
For Ron = RZQ/7 setting
NOTE:
1. In two cases, a maximum slew rate of 12 V/ns applies for a single DQ signal within a byte lane.
-Case 1 is defined for a single DQ signal within a byte lane which is switching into a certain direction (either from high
to low or low to high) while all remaining DQ signals in the same byte lane are static (i.e. they stay at either high or
low).
-Case 2 is defined for a single DQ signal within a byte lane which is switching into a certain direction (either from high
to low or low to high) while all remaining DQ signals in the same byte lane are switching into the opposite direction
(i.e. from low to high or high to low respectively). For the remaining DQ signal switching into the opposite direction,
the regular maximum limit of 9 V/ns applies
Rev. 1.4 / Sep.2017
39
Differential Output Slew Rate
With the reference load for timing measurements, output slew rate for falling and rising edges is defined
and measured between VOLdiff(AC) and VOHdiff(AC) for differential signals as shown in Table and Figure
below.
Differential output slew rate definition
Measured
Description
Defined by
From
To
[VOHdiff(AC)-VOLdiff(AC)] /
Delta TRdiff
VOLdiff(AC)
VOHdiff(AC)
Differential output slew rate for rising edge
[VOHdiff(AC)-VOLdiff(AC)] /
Delta TFdiff
VOHdiff(AC)
VOLdiff(AC)
Differential output slew rate for falling edge
NOTE :
1. Output slew rate is verified by design and characterization, and may not be subject to production test.
V
(AC)
OHdiff
V
(AC)
OLdiff
delta TFdiff
delta TRdiff
Differential Output Slew Rate Definition
Differential output slew rate
DDR4-1600 DDR4-1866 DDR4-2133 DDR4-2400 DDR4-2666 DDR4-2933 DDR4-3200
Min Max Min Max Min Max Min Max Min Max Min Max Min Max
Parameter
Symbol
Units
Differential output slew rate SRQdiff
Description:
8
18
8
18
8
18
8
18
8
18
8
18
8
18
V/ns
SR: Slew Rate
Q: Query Output (like in DQ, which stands for Data-in, Query-Output)
diff: Differential Signals
For Ron = RZQ/7 setting
Rev. 1.4 / Sep.2017
40
Single-ended AC & DC Output Levels of Connectivity Test Mode
Following output parameters will be applied for DDR4 SDRAM Output Signal during Connectivity Test
Mode.
Single-ended AC & DC output levels of Connectivity Test Mode
DDR4-1600/1866/2133/
Symbol Parameter
OH(DC) DC output high measurement level (for IV curve linearity)
Unit Note
2400/2666/3200
V
1.1 x VDDQ
V
V
V
V
V
V
VOM(DC) DC output mid measurement level (for IV curve linearity)
VOL(DC) DC output low measurement level (for IV curve linearity)
VOB(DC) DC output below measurement level (for IV curve linearity)
0.8 x VDDQ
0.5 x VDDQ
0.2 x VDDQ
V
OH(AC) AC output high measurement level (for output SR)
VTT + (0.1 x VDDQ
)
1
1
VOL(AC) AC output below measurement level (for output SR)
VTT - (0.1 x VDDQ
)
NOTE :
1. The effective test load is 50 terminated by VTT = 0.5 * VDDQ.
VOH(AC)
VTT
0.5 * VDDQ
VOL(AC)
TF_output_CT
TR_output_CT
Differential Output Slew Rate Definition of Connectivity Test Mode
Single-ended output slew rate of Connectivity Test Mode
DDR4-1600/1866/2133/2400/2666/3200
Parameter
Symbol
Unit Note
Min
Max
10
Output signal Falling time TF_output_CT
Output signal Rising time TR_output_CT
-
-
ns/V
ns/V
10
Rev. 1.4 / Sep.2017
41
Standard Speed Bins
DDR4-1600 Speed Bins and Operations
Speed Bin
DDR4-1600K
11-11-11
CL-nRCD-nRP
Unit NOTE
Parameter
Symbol
min
max
13.75
Internal read command to first
data
tAA
18.00
ns
ns
ns
10
10
10
(13.50)5,10
Internal read command to first
data with read DBI enabled
tAA_DBI
tRCD
tAA(min) + 2nCK
tAA(max) +2nCK
-
13.75
(13.50)5,10
ACT to internal read or write
delay time
13.75
PRE command period
tRP
tRAS
tRC
-
ns
ns
ns
10
10
10
(13.50)5,10
ACT to PRE command period
35
9 x tREFI
-
48.75
(48.50)5,10
ACT to ACT or REF command
period
Normal Read DBI
1,2,3,4,9,
12
CL = 9
CL = 11 tCK(AVG)
1.5
1.6
ns
CWL = 9
CL = 10 CL = 12 tCK(AVG)
CL = 10 CL = 12 tCK(AVG)
Reserved
ns 1,2,3,4,9
Reserved
ns
ns
1,2,3,4
1,2,3,4
1,2,3
11,12
11
CWL = 9,11 CL = 11 CL = 13 tCK(AVG)
CL = 12 CL = 14 tCK(AVG)
Supported CL Settings
1.25
1.25
<1.5
<1.5
ns
9,11,12
11,13,14
9,11
nCK
nCK
nCK
Supported CL Settings with read DBI
Supported CWL Settings
Rev. 1.4 / Sep.2017
42
DDR4-1866 Speed Bins and Operations
Speed Bin
DDR4-1866M
13-13-13
CL-nRCD-nRP
Unit NOTE
Parameter
Symbol
min
max
Internal read command to first
data
13.9212
tAA
18.00
ns
ns
ns
10
10
10
(13.50)5,10
Internal read command to first
data with read DBI enabled
tAA_DBI
tRCD
tAA(min) + 2nCK
tAA(max) +2nCK
-
13.92
(13.50)5,10
ACT to internal read or write delay
time
13.92
PRE command period
tRP
tRAS
tRC
-
ns
ns
ns
10
10
10
(13.50)5,10
ACT to PRE command period
34
9 x tREFI
-
47.92
(47.50)5,10
ACT to ACT or REF command
period
Normal Read DBI
1,2,3,4,9,
10
CL = 9
CL = 11 tCK(AVG)
1.5
1.6
ns
CWL = 9
CL = 10 CL = 12 tCK(AVG)
CL = 10 CL = 12 tCK(AVG)
Reserved
ns 1,2,3,4,9
ns
ns 1,2,3,4,6
Reserved
4
CWL = 9,11 CL = 11 CL = 13 tCK(AVG)
CL = 12 CL = 14 tCK(AVG)
CL = 12 CL = 14 tCK(AVG)
CWL = 10,12 CL = 13 CL = 15 tCK(AVG)
CL = 14 CL = 16 tCK(AVG)
Supported CL Settings
1.25
1.25
<1.5
<1.5
ns
ns
1,2,3,6
1,2,3,4
1,2,3,4
1,2,3
Reserved
1.071
1.071
<1.25
<1.25
ns
ns
9,11,12,13,14
11,13,14 ,15,16
9,10,11,12
nCK
nCK
nCK
11,12
12
Supported CL Settings with read DBI
Supported CWL Settings
Rev. 1.4 / Sep.2017
43
DDR4-2133 Speed Bins and Operations
Speed Bin
DDR4-2133P
15-15-15
CL-nRCD-nRP
Unit
NOTE
Parameter
Symbol
min
max
14.0612
Internal read command to first data
tAA
18.00
ns
ns
ns
10
10
10
(13.50)5,10
Internal read command to first data
with read DBI enabled
tAA_DBI
tRCD
tAA(min)+3nCK
tAA(max)+3nCK
-
14.06
(13.50)5,10
ACT to internal read or write delay
time
14.06
PRE command period
ACT to PRE command period
ACT to ACT or REF command period
Normal Read DBI
tRP
tRAS
tRC
-
ns
ns
ns
10
10
10
(13.50)5,10
33
9 x tREFI
-
47.06
(46.50)5,10
1,2,3,4,9,1
2
CL = 9
CL = 11 tCK(AVG)
1.5
1.6
ns
CWL = 9
CL = 10 CL = 12 tCK(AVG)
CL = 11 CL = 13 tCK(AVG)
CL = 12 CL = 14 tCK(AVG)
CL = 13 CL = 15 tCK(AVG)
CL = 14 CL = 16 tCK(AVG)
CL = 14 CL = 17 tCK(AVG)
Reserved
ns
ns
1,2,3,9
1,2,3,4,7
1,2,3,7
1,2,3,4,7
1,2,3,7
1,2,3,4
1,2,3,4
1,2,3
1.25
1.25
<1.5
<1.5
CWL = 9,11
ns
1.071
1.071
<1.25
<1.25
ns
CWL = 10,12
ns
Reserved
ns
CWL = 11,14 CL = 15 CL = 18 tCK(AVG)
CL = 16 CL = 19 tCK(AVG)
Supported CL Settings
0.937
0.937
<1.071
<1.071
ns
ns
9,11,12,13,14,15,16
11,13,14,15,16,18,19
9,10,11,12,14
nCK
nCK
nCK
11,12
Supported CL Settings with read DBI
Supported CWL Settings
Rev. 1.4 / Sep.2017
44
DDR4-2400 Speed Bins and Operations
Speed Bin
DDR4-2400T
17-17-17
CL-nRCD-nRP
Unit
NOTE
Parameter
Symbol
min
max
14.16
Internal read command to first data
tAA
18.00
ns
ns
ns
10
10
10
(13.75)5,10
Internal read command to first data
with read DBI enabled
tAA_DBI
tRCD
tAA(min)+3nCK
tAA(max)+3nCK
-
14.16
(13.75)5,10
ACT to internal read or write delay
time
14.16
PRE command period
ACT to PRE command period
ACT to ACT or REF command period
Normal Read DBI
tRP
tRAS
tRC
-
ns
ns
ns
10
10
10
(13.75)5,10
32
9 x tREFI
-
46.16
(45.75)5,10
CL = 9
CL = 11 tCK(AVG)
Reserved
ns
ns
1,2,3,4,9
1,2,3,4,9
4
CWL = 9
1.6
CL = 10 CL = 12 tCK(AVG)
CL = 10 CL = 12 tCK(AVG)
1.5
Reserved
Reserved
Reserved
ns
CWL = 9,11 CL = 11 CL = 13 tCK(AVG)
CL = 12 CL = 14 tCK(AVG)
1.25
1.25
<1.5
<1.5
ns
1,2,3,4,8
1,2,3,8
4
ns
CL = 12 CL = 14 tCK(AVG)
ns
CWL = 10,12 CL = 13 CL = 15 tCK(AVG)
CL = 14 CL = 16 tCK(AVG)
1.071
1.071
<1.25
<1.25
ns
1,2,3,4,8
1,2,3,8
4
ns
CL = 14 CL = 17 tCK(AVG)
ns
CWL = 11,14 CL = 15 CL = 18 tCK(AVG)
CL = 16 CL = 19 tCK(AVG)
0.937
0.937
<1.071
<1.071
ns
1,2,3,4,8
1,2,3,8
1,2,3,4
1,2,3,4
ns
CL = 15 CL = 18 tCK(AVG)
Reserved
Reserved
ns
CL = 16 CL = 19 tCK(AVG)
CWL = 12,16
ns
CL = 17 CL = 20 tCK(AVG)
0.833
0.833
<0.937
<0.937
ns
CL = 18 CL = 21 tCK(AVG)
Supported CL Settings
ns
1,2,3
11
10,11,12,13,14,15,16,17,18
12,13,14,15,16,18,19,20,21
9,10,11,12,14,16
nCK
nCK
nCK
Supported CL Settings with read DBI
Supported CWL Settings
Rev. 1.4 / Sep.2017
45
Speed Bin Table Notes
Absolute Specification
- VDDQ = VDD = 1.20V +/- 0.06 V
- VPP = 2.5V +0.25/-0.125 V
- The values defined with above-mentioned table are DLL ON case.
- DDR4-1600, 1866, 2133 and 2400 Speed Bin Tables are valid only when Geardown Mode is disabled.
1. The CL setting and CWL setting result in tCK(avg).MIN and tCK(avg).MAX requirements. When making
a selection of tCK(avg), both need to be fulfilled: Requirements from CL setting as well as require-
ments from CWL setting.
2. tCK(avg).MIN limits: Since CAS Latency is not purely analog - data and strobe output are synchronized
by the DLL - all possible intermediate frequencies may not be guaranteed. CL in clock cycle is calcu-
lated from tAA following rounding algorithm defined in DDR4 Device Operation(Rounding Algorithms)
3. tCK(avg).MAX limits: Calculate tCK(avg) = tAA.MAX / CL SELECTED and round the resulting tCK(avg)
down to the next valid speed bin (i.e. 1.5ns or 1.25ns or 1.071 ns or 0.938 ns or 0.833 ns). This result
is tCK(avg).MAX corresponding to CL SELECTED.
4. ‘Reserved’ settings are not allowed. User must program a different value.
5. 'Optional' settings allow certain devices in the industry to support this setting, however, it is not a
mandatory feature. Refer to supplier's data sheet and/or the DIMM SPD information if and how this
setting is supported.
6. Any DDR4-1866 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
7. Any DDR4-2133 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
8. Any DDR4-2400 speed bin also supports functional operation at lower frequencies as shown in the
table which are not subject to Production Tests but verified by Design/Characterization.
9. DDR4-1600 AC timing apply if DRAM operates at lower than 1600 MT/s data rate.
10. Parameters apply from tCK(avg)min to tCK(avg)max at all standard JEDEC clock period values as
stated in the Speed Bin Tables.
11. CL number in parentheses, it means that these numbers are optional.
12. DDR4 SDRAM supports CL=9 as long as a system meets tAA(min).
13. Each speed bin lists the timing requirements that need to be supported in order for a given DRAM to
be JEDEC compliant. JEDEC compliance does not require support for all speed bins within a given
speed. JEDEC compliance requires meeting the parameters for a least one of the listed speed bins.
Rev. 1.4 / Sep.2017
46
IDD and IDDQ Specification Parameters and Test Conditions
IDD, IPP and IDDQ Measurement Conditions
In this chapter, IDD, IPP and IDDQ measurement conditions such as test load and patterns are defined.
Figure shows the setup and test load for IDD, IPP and IDDQ measurements.
•
IDD currents (such as IDD0, IDD0A, IDD1, IDD1A, IDD2N, IDD2NA, IDD2NL, IDD2NT, IDD2P, IDD2Q,
IDD3N, IDD3NA, IDD3P, IDD4R, IDD4RA, IDD4W, IDD4WA, IDD5B, IDD5F2, IDD5F4, IDD6N, IDD6E,
IDD6R, IDD6A, IDD7 and IDD8) are measured as time-averaged currents with all VDD balls of the
DDR4 SDRAM under test tied together. Any IPP or IDDQ current is not included in IDD currents.
•
•
IPP currents have the same definition as IDD except that the current on the VPP supply is measured.
IDDQ currents (such as IDDQ2NT and IDDQ4R) are measured as time-averaged currents with all
VDDQ balls of the DDR4 SDRAM under test tied together. Any IDD current is not included in IDDQ cur-
rents.
Attention: IDDQ values cannot be directly used to calculate IO power of the DDR4 SDRAM. They can
be used to support correlation of simulated IO power to actual IO power as outlined in Figure 2. In
DRAM module application, IDDQ cannot be measured separately since VDD and VDDQ are using one
merged-power layer in Module PCB.
For IDD, IPP and IDDQ measurements, the following definitions apply:
•
•
•
•
•
•
•
“0” and “LOW” is defined as VIN <= VILAC(max).
“1” and “HIGH” is defined as VIN >= VIHAC(min).
“MID-LEVEL” is defined as inputs are VREF = VDD / 2.
Timings used for IDD, IPP and IDDQ Measurement-Loop Patterns are provided in Table 1.
Basic IDD, IPP and IDDQ Measurement Conditions are described in Table 2.
Detailed IDD, IPP and IDDQ Measurement-Loop Patterns are described in Table 3 through Table 11.
IDD Measurements are done after properly initializing the DDR4 SDRAM. This includes but is not lim-
ited to setting
RON = RZQ/7 (34 Ohm in MR1);
RTT_NOM = RZQ/6 (40 Ohm in MR1);
RTT_WR = RZQ/2 (120 Ohm in MR2);
RTT_PARK = Disable;
Qoff = 0 (Output Buffer enabled) in MR1;
B
TDQS_t disabled in MR1;
CRC disabled in MR2;
CA parity feature disabled in MR5;
Gear down mode disabled in MR3
Read/Write DBI disabled in MR5;
DM disabled in MR5
•
•
•
Attention: The IDD, IPP and IDDQ Measurement-Loop Patterns need to be executed at least one time
before actual IDD or IDDQ measurement is started.
Define D = {CS_n, ACT_n, RAS_n, CAS_n, WE_n } := {HIGH, LOW, LOW, LOW, LOW} ; apply BG/BA
changes when directed.
Define D# = {CS_n, ACT_n, RAS_n, CAS_n, WE_n } := {HIGH, HIGH, HIGH, HIGH, HIGH} ; apply
invert of BG/BA changes when directed above.
Rev. 1.4 / Sep.2017
47
I
I
I
DDQ
DD
PP
V
V
V
DDQ
DD
PP
RESET
CK_t/CK_c
DDR4 SDRAM
CKE
CS
C
DQS_t/DQS_c
DQ
DM
ACT,RAS,CAS,WE
A,BG,BA
ODT
V
V
SSQ
SS
ZQ
NOTE:
1. DIMM level Output test load condition may be different from above
Figure 1 - Measurement Setup and Test Load for IDD, IPP and IDDQ Measurements
Application specific
IDDQ
TestLad
memory channel
environment
Channel
IO Powe
Simulatin
IDDQ
Simuaion
IDDQ
Measurement
Correlation
X
X
Channel IO Power
Number
Figure 2 - Correlation from simulated Channel IO Power to actual Channel IO Power supported by IDDQ
Measurement
Rev. 1.4 / Sep.2017
48
Table 1 -Timings used for IDD, IPP and IDDQ Measurement-Loop Patterns
DDR4-1600
DDR4-1866
DDR4-2133
DDR4-2400
Symbol
Unit
11-11-11
13-13-13
15-15-15
17-17-17
tCK
CL
1.25
11
11
11
39
28
11
16
20
28
4
1.071
13
12
13
45
32
13
16
22
28
4
0.937
15
14
15
51
36
15
16
23
32
4
0.833
17
17
17
56
39
17
16
26
36
4
ns
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
nCK
CWL
nRCD
nRC
nRAS
nRP
x4
nFAW x8
x16
x4
nRRDS x8
x16
4
4
4
4
5
5
6
7
x4
5
5
6
6
nRRDL x8
x16
5
5
6
6
6
6
7
8
tCCD_S
tCCD_L
tWTR_S
tWTR_L
nRFC 2Gb
nRFC 4Gb
nRFC 8Gb
nRFC 16Gb
4
4
4
4
5
5
6
6
2
3
3
3
6
7
8
9
128
208
280
TBD
150
243
327
TBD
171
278
374
TBD
193
313
421
TBD
Rev. 1.4 / Sep.2017
49
Table 2 -Basic IDD, IPP and IDDQ Measurement Conditions
Symbol
Description
Operating One Bank Active-Precharge Current (AL=0)
CKE: High; External clock: On; tCK, nRC, nRAS, CL: see Table 1; BL: 81; AL: 0; CS_n: High
between ACT and PRE; Command, Address, Bank Group Address, Bank Address Inputs: partially
toggling according to Table 3; Data IO: VDDQ; DM_n: stable at 1; Bank Activity: Cycling with one
bank active at a time: 0,0,1,1,2,2,... (see Table 3); Output Buffer and RTT: Enabled in Mode Regis-
IDD0
ters2; ODT Signal: stable at 0; Pattern Details: see Table 3
Operating One Bank Active-Precharge Current (AL=CL-1)
AL = CL-1, Other conditions: see IDD0
IDD0A
IPP0
Operating One Bank Active-Precharge IPP Current
Same condition with IDD0
Operating One Bank Active-Read-Precharge Current (AL=0)
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, CL: see Table 1; BL: 81; AL: 0; CS_n: High
between ACT, RD and PRE; Command, Address, Bank Group Address, Bank Address Inputs,
Data IO: partially toggling according to Table 4; DM_n: stable at 1; Bank Activity: Cycling with one
bank active at a time: 0,0,1,1,2,2,... (see Table 4); Output Buffer and RTT: Enabled in Mode Regis-
IDD1
ters2; ODT Signal: stable at 0; Pattern Details: see Table 4
Operating One Bank Active-Read-Precharge Current (AL=CL-1)
AL = CL-1, Other conditions: see IDD1
IDD1A
IPP1
Operating One Bank Active-Read-Precharge IPP Current
Same condition with IDD1
Precharge Standby Current (AL=0)
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: stable at 1; Command,
Address, Bank Group Address, Bank Address Inputs: partially toggling according to Table 5; Data
IO: VDDQ; DM_n: stable at 1; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in
IDD2N
Mode Registers2; ODT Signal: stable at 0; Pattern Details: see Table 5
Precharge Standby Current (AL=CL-1)
AL = CL-1, Other conditions: see IDD2N
IDD2NA
IPP2N
Precharge Standby IPP Current
Same condition with IDD2N
Precharge Standby ODT Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: stable at 1; Command,
IDD2NT Address, Bank Group Address, Bank Address Inputs: partially toggling according to Table 6; Data
IO: VSSQ; DM_n: stable at 1; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in
Mode Registers2; ODT Signal: toggling according to Table 6; Pattern Details: see Table 6
IDDQ2NT Precharge Standby ODT IDDQ Current
(Optional) Same definition like for IDD2NT, however measuring IDDQ current instead of IDD current
Precharge Standby Current with CAL enabled
IDD2NL
Same definition like for IDD2N, CAL enabled3
Precharge Standby Current with Gear Down mode enabled
IDD2NG
Same definition like for IDD2N, Gear Down mode enabled3,5
Precharge Standby Current with DLL disabled
IDD2ND
Same definition like for IDD2N, DLL disabled3
Rev. 1.4 / Sep.2017
50
Precharge Standby Current with CA parity enabled
IDD2N_par
IDD2P
Same definition like for IDD2N, CA parity enabled3
Precharge Power-Down Current CKE: Low; External clock: On; tCK, CL: see Table 1; BL: 81; AL:
0; CS_n: stable at 1; Command, Address, Bank Group Address, Bank Address Inputs: stable at
0; Data IO: VDDQ; DM_n: stable at 1; Bank Activity: all banks closed; Output Buffer and RTT:
Enabled in Mode Registers2; ODT Signal: stable at 0
Precharge Power-Down IPP Current
Same condition with IDD2P
IPP2P
Precharge Quiet Standby Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: stable at 1; Command,
Address, Bank Group Address, Bank Address Inputs: stable at 0; Data IO: VDDQ; DM_n: stable
at 1;Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers2; ODT
Signal: stable at 0
IDD2Q
IDD3N
Active Standby Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: stable at 1; Command,
Address, Bank Group Address, Bank Address Inputs: partially toggling according to Table 5; Data
IO: VDDQ; DM_n: stable at 1;Bank Activity: all banks open; Output Buffer and RTT: Enabled in
Mode Registers2; ODT Signal: stable at 0; Pattern Details: see Table 5
Active Standby Current (AL=CL-1)
AL = CL-1, Other conditions: see IDD3N
IDD3NA
IPP3N
Active Standby IPP Current
Same condition with IDD3N
Active Power-Down Current
CKE: Low; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: stable at 1; Command,
Address, Bank Group Address, Bank Address Inputs: stable at 0; Data IO: VDDQ; DM_n: stable
at 1; Bank Activity: all banks open; Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal:
stable at 0
IDD3P
IPP3P
Active Power-Down IPP Current
Same condition with IDD3P
Operating Burst Read Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 82; AL: 0; CS_n: High between RD;
Command, Address, Bank Group Address, Bank Address Inputs: partially toggling according to
Table 7; Data IO: seamless read data burst with different data between one burst and the next one
according to Table 7; DM_n: stable at 1; Bank Activity: all banks open, RD commands cycling through
banks: 0,0,1,1,2,2,... (see Table 7); Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal:
stable at 0; Pattern Details: see Table 7
IDD4R
Operating Burst Read Current (AL=CL-1)
AL = CL-1, Other conditions: see IDD4R
IDD4RA
IDD4RB
IPP4R
Operating Burst Read Current with Read DBI
Read DBI enabled3, Other conditions: see IDD4R
Operating Burst Read IPP Current
Same condition with IDD4R
IDDQ4R Operating Burst Read IDDQ Current
(Optional) Same definition like for IDD4R, however measuring IDDQ current instead of IDD current
IDDQ4RB Operating Burst Read IDDQ Current with Read DBI
(Optional) Same definition like for IDD4RB, however measuring IDDQ current instead of IDD current
Rev. 1.4 / Sep.2017
51
Operating Burst Write Current
CKE: High; External clock: On; tCK, CL: see Table 1; BL: 81; AL: 0; CS_n: High between WR;
Command, Address, Bank Group Address, Bank Address Inputs: partially toggling according to
IDD4W Table 8; Data IO: seamless write data burst with different data between one burst and the next one
according to Table 8; DM_n: stable at 1; Bank Activity: all banks open, WR commands cycling through
banks: 0,0,1,1,2,2,... (see Table 8); Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal:
stable at HIGH; Pattern Details: see Table 8
Operating Burst Write Current (AL=CL-1)
IDD4WA
AL = CL-1, Other conditions: see IDD4W
Operating Burst Write Current with Write DBI
IDD4WB
Write DBI enabled3, Other conditions: see IDD4W
Operating Burst Write Current with Write CRC
IDD4WC
Write CRC enabled3, Other conditions: see IDD4W
Operating Burst Write Current with CA Parity
IDD4W_par
CA Parity enabled3, Other conditions: see IDD4W
Operating Burst Write IPP Current
IPP4W
Same condition with IDD4W
Burst Refresh Current (1X REF)
CKE: High; External clock: On; tCK, CL, nRFC: see Table 1; BL: 81; AL: 0; CS_n: High between REF;
Command, Address, Bank Group Address, Bank Address Inputs: partially toggling according to
IDD5B
Table 9; Data IO: VDDQ; DM_n: stable at 1; Bank Activity: REF command every nRFC (see Table 9);
Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal: stable at 0; Pattern Details: see
Table 9
Burst Refresh Write IPP Current (1X REF)
Same condition with IDD5B
IPP5B
Burst Refresh Current (2X REF)
IDD5F2
tRFC=tRFC_x2, Other conditions: see IDD5B
Burst Refresh Write IPP Current (2X REF)
IPP5F2
Same condition with IDD5F2
Burst Refresh Current (4X REF)
IDD5F4
tRFC=tRFC_x4, Other conditions: see IDD5B
Burst Refresh Write IPP Current (4X REF)
IPP5F4
Same condition with IDD5F4
Self Refresh Current: Normal Temperature Range
TCASE: 0 - 85°C; Low Power Array Self Refresh (LP ASR) : Normal4; CKE: Low; External clock:
IDD6N
IPP6N
IDD6E
IPP6E
Off; CK_t and CK_c#: LOW; CL: see Table 1; BL: 81; AL: 0; CS_n#, Command, Address, Bank Group
Address, Bank Address, Data IO: High; DM_n: stable at 1; Bank Activity: Self-Refresh operation;
Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal: MID-LEVEL
Self Refresh IPP Current: Normal Temperature Range
Same condition with IDD6N
Self-Refresh Current: Extended Temperature Range)
TCASE: 0 - 95°C; Low Power Array Self Refresh (LP ASR) : Extended4; CKE: Low; External clock:
Off; CK_t and CK_c: LOW; CL: see Table 1; BL: 81; AL: 0; CS_n, Command, Address, Bank Group
Address, Bank Address, Data IO: High; DM_n:stable at 1; Bank Activity: Extended Temperature
Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal: MID-LEVEL
Self Refresh IPP Current: Extended Temperature Range
Same condition with IDD6E
Rev. 1.4 / Sep.2017
52
Self-Refresh Current: Reduced Temperature Range
TCASE: 0 - TBD (~35-45)°C; Low Power Array Self Refresh (LP ASR) : Reduced4; CKE: Low;
External clock: Off; CK_t and CK_c#: LOW; CL: see Table 1; BL: 81; AL: 0; CS_n#, Command,
Address, Bank Group Address, Bank Address, Data IO: High; DM_n:stable at 1; Bank Activity:
Extended Temperature Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers2;
ODT Signal: MID-LEVEL
IDD6R
Self Refresh IPP Current: Reduced Temperature Range
Same condition with IDD6R
IPP6R
IDD6A
IPP6A
Auto Self-Refresh Current
TCASE: 0 - 95°C; Low Power Array Self Refresh (LP ASR) : Auto4; CKE: Low; External clock: Off;
CK_t and CK_c#: LOW; CL: see Table 1; BL: 81; AL: 0; CS_n#, Command, Address, Bank Group
Address, Bank Address, Data IO: High; DM_n:stable at 1; Bank Activity: Auto Self-Refresh
operation; Output Buffer and RTT: Enabled in Mode Registers2; ODT Signal: MID-LEVEL
Auto Self-Refresh IPP Current
Same condition with IDD6A
Operating Bank Interleave Read Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, nRRD, nFAW, CL: see Table 1; BL: 81; AL:
CL-1; CS_n: High between ACT and RDA; Command, Address, Bank Group Address, Bank Address
Inputs: partially toggling according to Table 10; Data IO: read data bursts with different data between
one burst and the next one according to Table 10; DM_n: stable at 1; Bank Activity: two times
interleaved cycling through banks (0, 1, ...7) with different addressing, see Table 10; Output Buffer and
RTT: Enabled in Mode Registers2; ODT Signal: stable at 0; Pattern Details: see Table 10
IDD7
Operating Bank Interleave Read IPP Current
Same condition with IDD7
IPP7
IDD8
IPP8
Maximum Power Down Current
TBD
Maximum Power Down IPP Current
Same condition with IDD8
Rev. 1.4 / Sep.2017
53
NOTE :
1. Burst Length: BL8 fixed by MRS: set MR0 [A1:0=00].
2. Output Buffer Enable
- set MR1 [A12 = 0] : Qoff = Output buffer enabled
- set MR1 [A2:1 = 00] : Output Driver Impedance Control = RZQ/7
RTT_Nom enable
- set MR1 [A10:8 = 011] : RTT_NOM = RZQ/6
RTT_WR enable
- set MR2 [A10:9 = 01] : RTT_WR = RZQ/2
RTT_PARK disable
- set MR5 [A8:6 = 000]
3. CAL enabled : set MR4 [A8:6 = 001] : 1600MT/s
010] : 1866MT/s, 2133MT/s
011] : 2400MT/s
Gear Down mode enabled :set MR3 [A3 = 1] : 1/4 Rate
DLL disabled : set MR1 [A0 = 0]
CA parity enabled :set MR5 [A2:0 = 001] : 1600MT/s,1866MT/s, 2133MT/s
010] : 2400MT/s
Read DBI enabled : set MR5 [A12 = 1]
Write DBI enabled : set :MR5 [A11 = 1]
4. Low Power Array Self Refresh (LP ASR) : set MR2 [A7:6 = 00] : Normal
01] : Reduced Temperature range
10] : Extended Temperature range
11] : Auto Self Refresh
5. IDD2NG should be measured after sync pulse(NOP) input.
Rev. 1.4 / Sep.2017
54
Table 3 - IDD0, IDD0A and IPP0 Measurement-Loop Pattern1
Data4
0
0
ACT
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-
-
1,2
D, D
D_#,
D_#
32
3,4
1
1
1
1
1
0
0
3
0
0
0
7
F
0
-
...
nRAS
...
repeat pattern 1...4 until nRAS - 1, truncate if necessary
PRE
repeat pattern 1...4 until nRC - 1, truncate if necessary
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
-
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 0 instead
1
2
1*nRC
2*nRC
3*nRC
4*nRC
5*nRC
6*nRC
7*nRC
8*nRC
9*nRC
10*nRC
11*nRC
12*nRC
13*nRC
14*nRC
15*nRC
3
4
5
6
7
8
9
10
11
12
13
14
15
For x4
and x8
only
NOTE:
1 .DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4. DQ signals are VDDQ.
Rev. 1.4 / Sep.2017
55
Table 4 - IDD1, IDD1A and IPP1 Measurement-Loop Patterna)
Data4
0 0
1, 2
ACT
D, D
D#, D#
0
1
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
0
0
0
0
0
3b
0
0
3
0
0
0
0
0
0
0
0
0
0
0
7
0
0
F
0
0
0
-
-
-
3, 4
...
repeat pattern 1...4 until nRCD - AL - 1, truncate if necessary
nRCD -AL
RD
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
D0=00, D1=FF
D2=FF, D3=00
D4=FF, D5=00
D6=00, D7=FF
...
repeat pattern 1...4 until nRAS - 1, truncate if necessary
nRAS
PRE
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
-
...
repeat pattern 1...4 until nRC - 1, truncate if necessary
1
1*nRC + 0
1*nRC + 1, 2 D, D
1*nRC + 3, 4 D#, D#
ACT
0
1
1
0
0
1
0
0
1
1
0
1
1
0
1
0
0
0
0
0
0
1
0
3b
1
0
3
0
0
0
0
0
0
0
0
0
0
0
7
0
0
F
0
0
0
-
-
-
...
repeat pattern nRC + 1...4 until 1*nRC + nRAS - 1, truncate if necessary
1*nRC + nRCD RD
- AL
0
1
1
0
1
0
0
1
1
0
0
0
0
0
0
D0=FF, D1=00
D2=00, D3=FF
D4=00, D5=FF
D6=FF, D7=00
...
1*nRC + nRAS PRE
... repeat nRC + 1...4 until 2*nRC - 1, truncate if necessary
repeat pattern 1...4 until nRAS - 1, truncate if necessary
0
1
0
1
0
0
0
1
1
0
0
0
0
0
0
-
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 1, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 0 instead
2 2*nRC
3 3*nRC
4 4*nRC
5 5*nRC
6 6*nRC
8 7*nRC
9 9*nRC
10 10*nRC
11 11*nRC
12 12*nRC
13 13*nRC
14 14*nRC
15 15*nRC
16 16*nRC
For x4 and x8 only
NOTE:
1. DQS_t, DQS_c are used according to RD Commands, otherwise VDDQ
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4.Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are VDDQ.
Rev. 1.4 / Sep.2017
56
Table 5 - IDD2N, IDD2NA, IDD2NL, IDD2NG, IDD2ND, IDD2N_par, IPP2,IDD3N,
IDD3NA and IDD3P
Measurement-Loop Pattern1
Data4
0 0
D, D
D, D
1
1
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
0
0
0
0
0
32
0
0
3
0
0
0
0
0
0
0
0
0
0
0
7
0
0
F
0
0
0
0
1
2
0
0
D#,
D#
32
3
D#,
D#
1
1
1
1
1
0
0
3
0
0
0
7
F
0
0
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 3, BA[1:0] = 0 instead
1 4-7
2 8-11
3 12-15
4 16-19
5 20-23
6 24-27
7 28-31
8 32-35
9 36-39
10 40-43
11 44-47
12 48-51
13 52-55
14 56-59
15 60-63
NOTE :
1. DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4. DQ signals are VDDQ.
Rev. 1.4 / Sep.2017
57
Table 6 - IDD2NT and IDDQ2NT Measurement-Loop Pattern1
Data4
0 0
D, D
1
1
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
0
0
0
0
0
32
32
0
0
3
0
0
0
0
0
0
0
0
0
0
0
7
0
0
F
0
0
0
-
-
-
1
2
D, D
D#, D#
3
D#, D#
1
1
1
1
1
0
0
3
0
0
0
7
F
0
-
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 1, BA[1:0] = 1 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, but ODT = 0 and BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 0, but ODT = 1 and BG[1:0]2 = 3, BA[1:0] = 0 instead
1 4-7
2 8-11
3 12-15
4 16-19
5 20-23
6 24-27
7 28-31
8 32-35
9 36-39
10 40-43
11 44-47
12 48-51
13 52-55
14 56-59
15 60-63
For x4
andx8
only
NOTE :
1. DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4. DQ signals are VDDQ.
Rev. 1.4 / Sep.2017
58
Table 7 - IDD4R, IDDR4RA, IDD4RB and IDDQ4R Measurement-Loop Pattern1
Data4
0
1
0
RD
0
1
1
0
1
0
0
0
0
32
1
0
0
0
0
0
0
0
D0=00, D1=FF
D2=FF, D3=00
D4=FF, D5=00
D6=00, D7=FF
1
D
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
2,3
D#, D#
4
RD
0
1
1
0
1
0
0
1
0
0
0
7
F
0
D0=FF, D1=00
D2=00, D3=FF
D4=00, D5=FF
D6=FF, D7=00
5
D
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
32
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
6,7
D#, D#
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 0 instead
2
3
4
5
6
7
8
9
8-11
12-15
16-19
20-23
24-27
28-31
32-35
36-39
10 40-43
11 44-47
12 48-51
13 52-55
14 56-59
15 60-63
For x4 and x8 only
NOTE :
1. DQS_t, DQS_c are used according to RD Commands, otherwise VDDQ.
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4. Burst Sequence driven on each DQ signal by Read Command.
Rev. 1.4 / Sep.2017
59
Table 8 - IDD4W, IDD4WA, IDD4WB and IDD4W_par Measurement-Loop Pattern1
Data4
0
1
0
WR
0
1
1
0
1
1
0
0
0
32
1
0
0
0
0
0
0
0
D0=00, D1=FF
D2=FF, D3=00
D4=FF, D5=00
D6=00, D7=FF
1
D
1
1
0
1
0
1
0
1
0
1
1
1
0
0
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
2,3
D#, D#
4
WR
0
1
1
0
1
1
0
1
0
0
0
7
F
0
D0=FF, D1=00
D2=00, D3=FF
D4=00, D5=FF
D6=FF, D7=00
5
D
1
1
0
1
0
1
0
1
0
1
1
1
0
0
0
32
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
6,7
D#, D#
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 0 instead
2
3
4
5
6
7
8
9
8-11
12-15
16-19
20-23
24-27
28-31
32-35
36-39
10 40-43
11 44-47
12 48-51
13 52-55
14 56-59
15 60-63
For x4 and x8 only
NOTE :
1. DQS_t, DQS_c are used according to WR Commands, otherwise VDDQ.
2. BG1 is don’t care for x16 device
3. C[2:0] are used only for 3DS device
4. Burst Sequence driven on each DQ signal by Write Command.
Rev. 1.4 / Sep.2017
60
Table 9 - IDD4WC Measurement-Loop Pattern1
Datad
0 0
WR
0
1
1
0
1
1
0
0
0
32
1
0
0
0
0
0
0
0
D0=00, D1=FF
D2=FF, D3=00
D4=FF, D5=00
D6=00, D7=FF
D8=CRC
1,2
D, D
1
1
0
1
0
1
0
1
0
1
1
1
0
0
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
3,4
5
D#, D#
WR
0
1
1
0
1
1
0
1
0
0
0
7
F
0
D0=FF, D1=00
D2=00, D3=FF
D4=00, D5=FF
D6=FF, D7=00
D8=CRC
6,7
8,9
D, D
1
1
0
1
0
1
0
1
0
1
1
1
0
0
0
32
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
-
D#, D#
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 0 instead
2 10-14
3 15-19
4 20-24
5 25-29
6 30-34
7 35-39
8 40-44
9 45-49
10 50-54
11 55-59
12 60-64
13 65-69
14 70-74
15 75-79
For x4 and x8 only
NOTE :
1. DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device.
3. C[2:0] are used only for 3DS device.
4. Burst Sequence driven on each DQ signal by Write Command.
Rev. 1.4 / Sep.2017
61
Table 10 - IDD5B Measurement-Loop Pattern1
Data4
0 0
1 1
2
REF
1
1
1
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
32
32
0
0
0
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7
0
0
0
F
0
0
0
0
-
-
-
-
D
D
3
D#, D#
4
D#, D#
1
1
1
1
1
0
0
3
0
0
0
7
F
0
-
repeat pattern 1...4, use BG[1:0]2 = 1, BA[1:0] = 1 instead
repeat pattern 1...4, use BG[1:0]2 = 0, BA[1:0] = 2 instead
repeat pattern 1...4, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat pattern 1...4, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat pattern 1...4, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat pattern 1...4, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat pattern 1...4, use BG[1:0]2 = 1, BA[1:0] = 0 instead
repeat pattern 1...4, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat pattern 1...4, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat pattern 1...4, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat pattern 1...4, use BG[1:0]2 = 3, BA[1:0] = 3 instead
repeat pattern 1...4, use BG[1:0]2 = 2, BA[1:0] = 1 instead
repeat pattern 1...4, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat pattern 1...4, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat pattern 1...4, use BG[1:0]2 = 3, BA[1:0] = 0 instead
4-7
8-11
12-15
16-19
20-23
24-27
28-31
32-35
36-39
40-43
44-47
48-51
52-55
56-59
60-63
For x4 and x8
only
2 64 ... nRFC - 1 repeat Sub-Loop 1, Truncate, if necessary
NOTE :
1. DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device.
3. C[2:0] are used only for 3DS device.
4. DQ signals are VDDQ.
Rev. 1.4 / Sep.2017
62
Table 11 - IDD7 Measurement-Loop Pattern1
Data4
0 0
1
ACT
RDA
0
0
0
1
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
-
D0=00, D1=FF
D2=FF, D3=00
D4=FF, D5=00
D6=00, D7=FF
-
2
3
D
D#
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
32
0
3
0
0
0
0
0
0
0
7
0
F
0
0
-
...
1 nRRD
nRRD + 1
repeat pattern 2...3 until nRRD - 1, if nRRD > 4. Truncate if necessary
ACT
RDA
0
0
0
1
0
1
0
0
0
1
0
0
0
1
1
1
1
0
0
0
0
0
1
0
0
0
0
0
0
-
D0=FF, D1=00
D2=00, D3=FF
D4=00, D5=FF
D6=FF, D7=00
...
repeat pattern 2 ... 3 until 2*nRRD - 1, if nRRD > 4. Truncate if necessary
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead
2 2*nRRD
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead
repeat pattern 2 ... 3 until nFAW - 1, if nFAW > 4*nRRD. Truncate if necessary
3 3*nRRD
4 4*nRRD
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead
5 nFAW
6 nFAW + nRRD
7 nFAW + 2*nRRD
8 nFAW + 3*nRRD
9 nFAW + 4*nRRD repeat Sub-Loop 4
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 1 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 3 instead
10 2*nFAW
11 2*nFAW + nRRD
12 2*nFAW + 2*nRRD
13 2*nFAW + 3*nRRD
14 2*nFAW + 4*nRRD repeat Sub-Loop 4
For x4 and x8
only
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead
15 3*nFAW
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 2 instead
repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead
repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 0 instead
16 3*nFAW + nRRD
17 3*nFAW + 2*nRRD
18 3*nFAW + 3*nRRD
19 3*nFAW + 4*nRRD repeat Sub-Loop 4
20 4*nFAW repeat pattern 2 ... 3 until nRC - 1, if nRC > 4*nFAW. Truncate if necessary
NOTE :
1. DQS_t, DQS_c are VDDQ.
2. BG1 is don’t care for x16 device.
3. C[2:0] are used only for 3DS device.
4. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are VDDQ
Rev. 1.4 / Sep.2017
63
IDD Specifications (Tcase: 0 to 95oC)
4GB, 512Mx 64 SO-DIMM: HMA851S6AFR6N
IDD
IPP
2133
40
40
13
13
72
72
72
unit note
unit note
Symbol
IDD0
IDD0A
IDD1
2133
176
176
228
240
104
104
124
72
104
104
104
72
2400
184
184
240
252
108
108
128
72
104
104
104
72
Symbol
IPP0
IPP1
2400
40
40
13
13
72
72
72
72
260
184
160
16
28
16
28
96
13
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
IPP2N
IPP2P
IPP3N
IPP3P
IPP4R
IPP4W
IPP5B
IPP5F2
IPP5F4
IPP6N
IPP6E
IPP6R
IPP6A
IPP7
IDD1A
IDD2N
IDD2NA
IDD2NT
IDD2NL
IDD2NG
IDD2ND
IDD2NP
IDD2P
IDD2Q
IDD3N
IDD3NA
IDD3P
IDD4R
IDD4RA
IDD4RB
IDD4W
IDD4WA
IDD4WB
IDD4WC
IDD4WP
IDD5B
IDD5F2
IDD5F4
IDD6N
IDD6E
72
260
180
160
16
28
16
28
96
13
88
88
176
176
144
708
748
736
616
628
616
592
656
780
560
492
88
180
180
148
780
816
816
680
688
680
656
744
784
568
508
88
IPP8
112
56
112
724
48
112
56
112
740
48
IDD6R
IDD6A
IDD7
IDD8
Rev. 1.4 / Sep.2017
64
8GB, 1Gx 64 SO-DIMM: HMA81GS6AFR8N
IDD
IPP
2133
48
56
26
unit note
unit note
Symbol
IDD0
IDD0A
IDD1
2133
296
296
368
392
208
208
248
144
208
208
208
144
176
352
352
288
920
992
992
888
912
880
848
904
1560
1120
984
176
224
112
224
1160
96
2400
304
304
384
408
216
216
256
144
208
208
208
144
176
360
360
296
992
1072
1072
960
984
960
912
1088
1568
1136
1016
176
224
112
224
1216
96
Symbol
IPP0
IPP1
2400
48
56
26
26
120
120
120
120
520
368
320
32
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
IPP2N
IPP2P
IPP3N
IPP3P
IPP4R
IPP4W
IPP5B
IPP5F2
IPP5F4
IPP6N
IPP6E
IPP6R
IPP6A
IPP7
IDD1A
IDD2N
IDD2NA
IDD2NT
IDD2NL
IDD2NG
IDD2ND
IDD2NP
IDD2P
IDD2Q
IDD3N
IDD3NA
IDD3P
IDD4R
IDD4RA
IDD4RB
IDD4W
IDD4WA
IDD4WB
IDD4WC
IDD4WP
IDD5B
IDD5F2
IDD5F4
IDD6N
IDD6E
26
120
120
120
120
520
360
320
32
56
33
56
152
26
56
33
56
152
26
IPP8
IDD6R
IDD6A
IDD7
IDD8
Rev. 1.4 / Sep.2017
65
8GB, 1Gx 72 SO-DIMM: HMA81GS7AFR8N
IDD
2133
333
IPP
2133
54
unit note
unit note
Symbol
IDD0
IDD0A
IDD1
2400
342
Symbol
IPP0
2400
54
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
333
411
441
234
234
279
162
234
234
234
162
198
396
396
324
342
432
459
243
243
288
162
234
234
234
162
198
405
405
333
1116
1206
1206
1080
1107
1080
1026
1224
1764
1278
1143
198
252
126
252
1368
108
IPP1
63
29
29
63
29
29
IPP2N
IPP2P
IPP3N
IPP3P
IPP4R
IPP4W
IPP5B
IPP5F2
IPP5F4
IPP6N
IPP6E
IPP6R
IPP6A
IPP7
IDD1A
IDD2N
IDD2NA
IDD2NT
IDD2NL
IDD2NG
IDD2ND
IDD2NP
IDD2P
IDD2Q
IDD3N
IDD3NA
IDD3P
IDD4R
IDD4RA
IDD4RB
IDD4W
IDD4WA
IDD4WB
IDD4WC
IDD4WP
IDD5B
IDD5F2
IDD5F4
IDD6N
IDD6E
135
135
135
135
585
405
360
36
63
37
63
171
29
135
135
135
135
585
414
360
36
63
37
63
171
29
1035
1116
1116
999
1026
990
IPP8
954
1017
1755
1260
1107
198
252
126
252
1305
108
IDD6R
IDD6A
IDD7
IDD8
Rev. 1.4 / Sep.2017
66
16GB, 2Gx 64 SO-DIMM: HMA82GS6AFR8N
IDD
2133
504
IPP
2133
74
unit note
unit note
Symbol
IDD0
IDD0A
IDD1
2400
520
Symbol
IPP0
2400
74
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
504
576
600
416
416
496
288
416
416
416
288
352
704
704
576
1128
1200
1200
1096
1120
1088
1056
1112
1768
1328
1192
352
448
224
448
1368
192
520
600
624
432
432
512
288
416
416
416
288
352
720
720
592
1208
1288
1288
1176
1200
1176
1128
1304
1784
1352
1232
352
448
224
448
1432
192
IPP1
82
51
51
82
51
51
IPP2N
IPP2P
IPP3N
IPP3P
IPP4R
IPP4W
IPP5B
IPP5F2
IPP5F4
IPP6N
IPP6E
IPP6R
IPP6A
IPP7
IDD1A
IDD2N
IDD2NA
IDD2NT
IDD2NL
IDD2NG
IDD2ND
IDD2NP
IDD2P
IDD2Q
IDD3N
IDD3NA
IDD3P
IDD4R
IDD4RA
IDD4RB
IDD4W
IDD4WA
IDD4WB
IDD4WC
IDD4WP
IDD5B
IDD5F2
IDD5F4
IDD6N
IDD6E
240
240
146
146
546
386
346
64
112
66
112
178
51
240
240
146
146
546
394
346
64
112
66
112
178
51
IPP8
IDD6R
IDD6A
IDD7
IDD8
Rev. 1.4 / Sep.2017
67
16GB, 2Gx 72 SO-DIMM: HMA82GS7AFR8N
IDD
2133
567
IPP
2133
83
unit note
unit note
Symbol
IDD0
IDD0A
IDD1
2400
585
Symbol
IPP0
2400
83
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
567
648
675
468
468
558
324
468
468
468
324
396
792
792
648
1269
1350
1350
1233
1260
1224
1188
1251
1989
1494
1341
396
504
252
504
1539
216
585
675
702
486
486
576
324
468
468
468
324
396
810
810
666
1359
1449
1449
1323
1350
1323
1269
1467
2007
1521
1386
396
504
252
504
1611
216
IPP1
92
58
58
92
58
58
IPP2N
IPP2P
IPP3N
IPP3P
IPP4R
IPP4W
IPP5B
IPP5F2
IPP5F4
IPP6N
IPP6E
IPP6R
IPP6A
IPP7
IDD1A
IDD2N
IDD2NA
IDD2NT
IDD2NL
IDD2NG
IDD2ND
IDD2NP
IDD2P
IDD2Q
IDD3N
IDD3NA
IDD3P
IDD4R
IDD4RA
IDD4RB
IDD4W
IDD4WA
IDD4WB
IDD4WC
IDD4WP
IDD5B
IDD5F2
IDD5F4
IDD6N
IDD6E
270
270
164
164
614
434
389
72
126
74
126
200
58
270
270
164
164
614
443
389
72
126
74
126
200
58
IPP8
IDD6R
IDD6A
IDD7
IDD8
Rev. 1.4 / Sep.2017
68
Module Dimensions
512Mx64 - HMA851S6AFR6N
Front
Side
3.5mm max
69.60mm
1.75
4.000.10
SPD
Detail-A
pin 1
pin 260
1.425
2.50
1.675
1.20±0.10
35.50
28.50
2X1.800.10
Back
Detail - A
1.00
±0.05
0.50
0.35±0.03
Note-metalized
keep out area Max 0.30
Max 0.25
0.20±0.15
Note:
1. 0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.4 / Sep.2017
69
1Gx64 - HMA81GS6AFR8N
Front
Side
69.60mm
3.7mm max
1.75
4.000.10
SPD
Detail-A
pin 1
pin 260
1.425
2.50
1.675
1.20±0.10
35.50
28.50
2X1.800.10
Back
Detail - A
±0.05
1.00
0.50
0.35±0.03
Note-metalized
keep out area Max 0.30
Max 0.25
0.20±0.15
Note:
1. 0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.4 / Sep.2017
70
1Gx72 - HMA81GS7AFR8N
Front
Side
69.60mm
3.7mm max
1.75
4.000.10
SPD/TS
Detail-A
pin 1
pin 260
1.425
2.50
1.675
1.20±0.10
35.50
28.50
2X1.800.10
Back
Detail - A
1.00
±0.05
0.50
0.35±0.03
Note-metalized
keep out area Max 0.30
Max 0.25
0.20±0.15
Note:
1. 0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.4 / Sep.2017
71
2Gx64 - HMA82GS6AFR8N
Front
Side
3.7mm max
69.60mm
1.75
4.000.10
SPD
Detail-A
pin 1
pin 260
1.425
2.50
1.675
1.20±0.10
35.50
28.50
2X1.800.10
Back
Detail - A
1.00
±0.05
0.50
0.35±0.03
Note-metalized
keep out area Max 0.30
Max 0.25
0.20±0.15
Note:
1. 0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.4 / Sep.2017
72
2Gx72 - HMA82GS7AFR8N
Front
Side
3.7mm max
69.60mm
1.75
4.000.10
SPD/TS
Detail-A
pin 1
pin 260
1.425
2.50
1.675
1.20±0.10
35.50
28.50
2X1.800.10
Back
Detail - A
1.00
±0.05
0.50
0.35±0.03
Note-metalized
keep out area Max 0.30
Max 0.25
0.20±0.15
Note:
1. 0.13 tolerance on all dimensions unless otherwise stated.
Units: millimeters
Rev. 1.4 / Sep.2017
73
相关型号:
©2020 ICPDF网 联系我们和版权申明