ICS84320AI01 [ICSI]
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL; 780MHZ ，水晶- TO- 3.3V的差分
| 型号： | ICS84320AI01 |
| 厂家： | 
INTEGRATED CIRCUIT SOLUTION INC |
| 描述： | 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL |
| 文件： | 总18页 (文件大小：192K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
GENERAL DESCRIPTION
FEATURES
The ICS84320I-01 is a general purpose, dual • Dual differential 3.3V LVPECL outputs
ICS
HiPerClockS™
output Crystal-to-3.3V Differential LVPECL
High Frequency Synthesizer and a member of
the HiPerClockS™ family of High Performance
Clock Solutions from ICS. The ICS84320I-01
• Selectable crystal oscillator interface
or LVCMOS/LVTTLTEST_CLK
• Output frequency range: 77.5MHz to 780MHz
• Crystal input frequency range: 14MHz to 40MHz
• VCO range: 620MHz to 780MHz
has a selectable TEST_CLK or crystal inputs. The VCO
operates at a frequency range of 620MHz to 780MHz. The
VCO frequency is programmed in steps equal to the
value of the input reference or crystal frequency. The VCO
and output frequency can be programmed using the
serial or parallel interfaces to the configuration logic. The
low phase noise characteristics of the ICS84320I-01
make it an ideal clock source for 10 Gigabit Ethernet,
SONET, and Serial Attached SCSI applications.
• Parallel or serial interface for programming counter
and output dividers
• Duty cycle: 44% - 56% (N > 1)
• RMS period jitter: 2.0ps (typical)
• RMS phase jitter at 155.52MHz, using a 38.88MHz crystal
(12kHz to 20MHz): 2.38ps (typical)
• RMS phase noise at 155.52MHz (typical)
Offset
Noise Power
100Hz ................ -90.5 dBc/Hz
1kHz ............... -114.2 dBc/Hz
10kHz ............... -123.6 dBc/Hz
100kHz ............... -128.1 dBc/Hz
• 3.3V supply voltage
• -40°C to 85°C ambient operating temperature
• Available in both, Standard and RoHS/Lead-Free
compliant packages
BLOCK DIAGRAM
VCO_SEL
PIN ASSIGNMENT
XTAL_SEL
TEST_CLK
0
XTAL_IN
1
OSC
XTAL_OUT
32 31 30 29 28 27 26 25
M5
M6
M7
M8
N0
N1
nc
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
XTAL_OUT
TEST_CLK
XTAL_SEL
VCCA
PLL
ICS84320I-01
32-Lead LQFP
7mm x 7mm x 1.4mm
package body
Y Package
÷ N
PHASE DETECTOR
÷ 1
÷ 2
÷ 4
÷ 8
MR
0
1
S_LOAD
S_DATA
S_CLOCK
MR
VCO
FOUT0
nFOUT0
FOUT1
nFOUT1
÷ M
Top View
VEE
S_LOAD
S_DATA
S_CLOCK
nP_LOAD
CONFIGURATION
INTERFACE
LOGIC
9
10 11 12 13 14 15 16
TEST
M0:M8
N0:N1
The Preliminary Information presented herein represents a product in prototyping or pre-production.The noted characteristics are based on initial
product characterization. Integrated Circuit Systems, Incorporated (ICS) reserves the right to change any circuitry or specifications without notice.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
1
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
FUNCTIONAL DESCRIPTION
NOTE: The functional description that follows describes op- matically occur during power-up.TheTEST output is LOW when
eration using a 25MHz crystal. Valid PLL loop divider values operating in the parallel input mode.The relation-ship between
for different crystal or input frequencies are defined in the In- the VCO frequency, the crystal frequency and the M divider is
put Frequency Characteristics, Table 5, NOTE 1.
defined as follows:
fVCO = fxtal x M
The ICS84320I-01 features a fully integrated PLL and there-
fore requires no external components for setting the loop band- The M value and the required values of M0 through M8 are
width. A fundamental crystal is used as the input to the on- shown in Table 3B to program the VCO Frequency Function
chip oscillator.The output of the oscillator is fed into the phase Table.Valid M values for which the PLL will achieve lock for a
detector. A 25MHz crystal provides a 25MHz phase detector 25MHz reference are defined as 25 ≤ M ≤ 31.The frequency
reference frequency. The VCO of the PLL operates over a out is defined as follows:
range of 620MHz to 780MHz. The output of the M divider is
also applied to the phase detector.
FOUT = fVCO = fxtal x M
N
N
Serial operation occurs when nP_LOAD is HIGH and S_LOAD
The phase detector and the M divider force the VCO output fre- is LOW. The shift register is loaded by sampling the S_DATA
quency to be M times the reference frequency by adjusting the bits with the rising edge of S_CLOCK. The contents of the
VCO control voltage. Note that for some values of M (either too shift register are loaded into the M divider and N output di-
high or too low), the PLL will not achieve lock. The output of the vider when S_LOAD transitions from LOW-to-HIGH. The M
VCO is scaled by a divider prior to being sent to each of the LVPECL divide and N output divide values are latched on the HIGH-to-
output buffers.The divider provides a 50% output duty cycle.
LOW transition of S_LOAD. If S_LOAD is held HIGH, data at
the S_DATA input is passed directly to the M divider and N
The programmable features of the ICS84320I-01 support two output divider on each rising edge of S_CLOCK. The serial
input modes to program the M divider and N output divider. The
two input operational modes are parallel and serial. Figure 1 shows
the timing diagram for each mode. In parallel mode, the nP_LOAD
input is initially LOW. The data on inputs M0 through M8 and N0
and N1 is passed directly to the M divider and N output divider.
On the LOW-to-HIGH transition of the nP_LOAD input, the data
is latched and the M divider remains loaded until the next
LOW transition on nP_LOAD or until a serial event occurs. As a
result, the M and N bits can be hardwired to set the M divider
and N output divider to a specific default state that will auto-
mode can be used to program the M and N bits and test bits
T1 andT0.The internal registers T0 andT1 determine the state
of the TEST output as follows:
T1 T0
TEST Output
LOW
0
0
1
1
0
1
0
1
S_Data, Shift Register Input
Output of M divider
CMOS Fout
SERIAL
L
OADING
S_CLOCK
S_DATA
S_LOAD
T 1
T0
*
NULL N1
N0
M8
M7
M6
M5
M4 M3
M2
M1
M0
t
t
H
S
nP_LOAD
t
S
PARALLEL LOADING
M, N
M0:M8, N0:N1
nP_LOAD
t
t
H
S
S_LOAD
Time
FIGURE 1. PARALLEL & SERIAL LOAD OPERATIONS
*NOTE: The NULL timing slot must be observed.
www.icst.com/products/hiperclocks.html
84320AYI-01
REV.A AUGUST 11, 2005
2
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TABLE 1. PIN DESCRIPTIONS
Number
Name
Type
Pullup
Description
1
M5
Input
Input
M divider inputs. Data latched on LOW-to-HIGH transition of
nP_LOAD input. LVCMOS / LVTTL interface levels.
2, 3, 4,
28, 29,
30, 31, 32
M6, M7, M8,
M0, M1,
M2, M3, M4
Pulldown
Pulldown
Determines output divider value as defined in Table 3C,
Function Table. LVCMOS / LVTTL interface levels.
5, 6
N0, N1
Input
7
nc
Unused
Power
No connect.
8, 16
VEE
Negative supply pins.
Test output which is ACTIVE in the serial mode of operation.
Output driven LOW in parallel mode.
9
TEST
Output
LVCMOS/LVTTL interface levels.
10
VCC
Power
Core supply pin.
11, 12
13
FOUT1, nFOUT1 Output
VCCO Power
FOUT0, nFOUT0 Output
Differential output for the synthesizer. LVPECL interface levels.
Output supply pin.
14, 15
Differential output for the synthesizer. LVPECL interface levels.
Active High Master Reset. When logic HIGH, forces the internal
dividers are reset causing the true outputs FOUTx to go low and the
17
MR
Input
Pulldown inverted outputs nFOUTx to go high. When logic LOW, the internal
dividers and the outputs are enabled. Assertion of MR does not
affect loaded M, N, and T values. LVCMOS / LVTTL interface levels.
Clocks in serial data present at S_DATA input into the shift register
on the rising edge of S_CLOCK. LVCMOS/LVTTL interface levels.
Shift register serial input. Data sampled on the rising edge of
S_CLOCK. LVCMOS/LVTTL interface levels.
18
19
S_CLOCK
S_DATA
Input
Input
Pulldown
Pulldown
Controls transition of data from shift register into the dividers.
LVCMOS / LVTTL interface levels.
20
21
S_LOAD
VCCA
Input
Pulldown
Power
Analog supply pin.
Selects between crystal or test inputs as the PLL reference source.
22
XTAL_SEL
TEST_CLK
Input
Pullup
Selects XTAL inputs when HIGH. Selects TEST_CLK when LOW.
LVCMOS / LVTTL interface levels.
23
Input
Input
Pulldown Test clock input. LVCMOS / LVTTL interface levels.
XTAL_OUT,
XTAL_IN
Crystal oscillator interface. XTAL_IN is the input.
XTAL_OUT is the output.
24, 25
Parallel load input. Determines when data present at M8:M0 is
Pulldown loaded into M divider, and when data present at N1:N0 sets the
N output divider value. LVCMOS / LVTTL interface levels.
26
nP_LOAD
Input
Determines whether synthesizer is in PLL or bypass mode.
LVCMOS / LVTTL interface levels.
27
VCO_SEL
Input
Pullup
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
TABLE 2. PIN CHARACTERISTICS
Symbol
CIN
Parameter
Test Conditions
Minimum Typical Maximum Units
Input Capacitance
Input Pullup Resistor
4
pF
kΩ
kΩ
RPULLUP
51
51
RPULLDOWN Input Pulldown Resistor
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
3
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TABLE 3A. PARALLEL AND SERIAL MODE FUNCTION TABLE
Inputs
Conditions
MR nP_LOAD
M
N
S_LOAD S_CLOCK S_DATA
H
X
X
X
X
X
X
Reset. Forces outputs LOW.
Data on M and N inputs passed directly to the M
divider and N output divider. TEST output forced LOW.
L
L
Data Data
Data Data
X
X
X
Data is latched into input registers and remains loaded
until next LOW transition or until a serial event occurs.
Serial input mode. Shift register is loaded with data on
S_DATA on each rising edge of S_CLOCK.
Contents of the shift register are passed to the
M divider and N output divider.
L
L
L
↑
L
L
↑
X
↑
L
X
H
H
X
X
X
X
Data
Data
L
L
L
H
H
H
X
X
X
X
X
X
↓
L
L
X
↑
Data
X
M divider and N output divider values are latched.
Parallel or serial input do not affect shift registers.
S_DATA passed directly to M divider as it is clocked.
H
Data
NOTE: L = LOW
H = HIGH
X = Don't care
↑ = Rising edge transition
↓= Falling edge transition
TABLE 3B. PROGRAMMABLE VCO FREQUENCY FUNCTION TABLE
256
M8
0
128
M7
0
64
M6
0
32
M5
0
16
M4
1
8
M3
1
4
M2
0
2
M1
0
1
M0
1
VCO Frequency
(MHz)
M Divide
625
•
25
•
•
•
•
•
•
•
•
•
•
700
•
28
•
0
0
0
0
1
1
1
0
0
•
•
•
•
•
•
•
•
•
775
31
0
0
0
0
1
1
1
1
1
NOTE 1: These M divide values and the resulting frequencies correspond to crystal or TEST_CLK input frequency
of 25MHz.
TABLE 3C. PROGRAMMABLE OUTPUT DIVIDER FUNCTION TABLE
Inputs
Output Frequency (MHz)
N Divider Value
N1
N0
0
Minimum
620
Maximum
780
0
0
1
1
1
2
4
8
1
310
390
0
155
195
1
77.5
97.5
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
4
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
ABSOLUTE MAXIMUM RATINGS
SupplyVoltage, V
4.6V
NOTE: Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the
device.These ratings are stress specifications only.Functional
operation of product at these conditions or any conditions be-
yond those listed in the DC Characteristics or AC Character-
istics is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect product reliability.
CC
Inputs, V
-0.5V to VCC + 0.5 V
I
Outputs, VO (LVCMOS)
-0.5V to VCCO + 0.5V
Outputs, IO (LVPECL)
Continuous Current
Surge Current
50mA
100mA
PackageThermal Impedance, θ
47.9°C/W (0 lfpm)
-65°C to 150°C
JA
StorageTemperature, T
STG
TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V 5%, TA = -40°C TO 85°C
Symbol Parameter
Test Conditions
Minimum
3.135
Typical
3.3
Maximum Units
VCC
VCCA
VCCO
IEE
Core Supply Voltage
3.465
3.465
3.465
155
V
V
Analog Supply Voltage
Output Supply Voltage
Power Supply Current
Analog Supply Current
3.135
3.3
3.135
3.3
V
mA
mA
ICCA
22
TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V 5%, TA = -40°C TO 85°C
Symbol Parameter
Test Conditions
Minimum Typical Maximum Units
VCO_SEL, XTAL_SEL, MR,
S_LOAD, nP_LOAD, N0:N1,
S_DATA, S_CLOCK, M0:M8
2
VCC + 0.3
VCC + 0.3
0.8
V
V
Input
VIH
High Voltage
TEST_CLK
2
VCO_SEL, XTAL_SEL, MR,
S_LOAD, nP_LOAD, N0:N1,
S_DATA, S_CLOCK, M0:M8
-0.3
-0.3
V
Input
VIL
Low Voltage
TEST_CLK
1.3
V
M0-M4, M6-M8, N0, N1, MR,
S_CLOCK, TEST_CLK,
S_DATA, S_LOAD, nP_LOAD
V
CC = VIN = 3.465V
150
µA
Input
IIH
High Current
M5, XTAL_SEL, VCO_SEL
VCC = VIN = 3.465V
5
µA
µA
M0-M4, M6-M8, N0, N1, MR,
S_CLOCK, TEST_CLK,
S_DATA, S_LOAD, nP_LOAD
V
CC = 3.465V,
VIN = 0V
-5
Input
IIL
Low Current
VCC = 3.465V,
VIN = 0V
M5, XTAL_SEL, VCO_SEL
TEST; NOTE 1
-150
2.6
µA
V
Output
VOH
High Voltage
Output
VOL
TEST; NOTE 1
0.5
V
Low Voltage
NOTE 1:Outputs terminated with 50Ω toVCCO/2.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
5
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TABLE 4C. LVPECL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V 5%, TA = -40°C TO 85°C
Symbol Parameter Test Conditions Minimum Typical Maximum Units
VOH
Output High Voltage; NOTE 1
VCCO - 1.4
VCCO - 2.0
0.6
VCCO - 0.9
VCCO - 1.7
1.0
V
V
V
VOL
Output Low Voltage; NOTE 1
VSWING
Peak-to-Peak Output Voltage Swing
NOTE 1: Outputs terminated with 50 Ω to VCCO - 2V. See "Parameter Measurement Information" section,
"3.3V Output Load Test Circuit".
TABLE 5. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V 5%, TA = -40°C TO 85°C
Symbol Parameter
Test Conditions
Minimum Typical Maximum Units
TEST_CLK; NOTE 1
14
40
40
50
MHz
MHz
MHz
XTAL_IN, XTAL_OUT;
NOTE 1
fIN
Input Frequency
14
S_CLOCK
NOTE 1: For the input crystal and TEST_CLK frequency range, the M value must be set for the VCO to operate within the
620MHz to780MHz range. Using the minimum input frequency of 14MHz, valid values of M are 45 ≤ M ≤ 55. Using the
maximum frequency of 40MHz, valid values of M are 16 ≤ M ≤ 19.
TABLE 6. CRYSTAL CHARACTERISTICS
Parameter
Test Conditions
Minimum Typical Maximum
Units
Mode of Oscillation
Frequency
Fundamental
14
40
50
7
MHz
Ω
Equivalent Series Resistance (ESR)
Shunt Capacitance
Drive Level
pF
1
mW
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
6
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TABLE 7. AC CHARACTERISTICS, VCC =VCCA = VCCO = 3.3V 5%, TA = -40°C TO 85°C
Symbol Parameter
Test Conditions
fOUT > 100MHz
20% to 80%
Minimum
Typical
Maximum
780
Units
MHz
ps
FOUT
Output Frequency
77.5
tjit(per)
tsk(o)
tR / tF
Period Jitter, RMS; NOTE 1
Output Skew; NOTE 2, 3
Output Rise/Fall Time
2.0
2.6
15
ps
100
700
ps
M, N to nP_LOAD
5
ns
tS
Setup Time S_DATA to S_CLOCK
S_CLOCK to S_LOAD
5
ns
5
ns
M, N to nP_LOAD
5
ns
tH
Hold Time
S_DATA to S_CLOCK
S_CLOCK to S_LOAD
5
ns
5
ns
N > 1
fOUT ≤ 625
ƒ> 625
49
44
51
%
odc
Output Duty Cycle
56
%
tPW
Output Pulse Width
PLL Lock Time
tPERIOD/2 - 150
tPERIOD/2 + 150
1
ps
tLOCK
ms
See Parameter Measurement Information section.
NOTE 1: Jitter performance using XTAL inputs.
NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 3: This parameter is defined in accordance with JEDEC Standard 65.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
7
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TYPICAL PHASE NOISE AT 155.52MHZ
0
-10
-20
OC-48 Sonet Bandpass Filter
-30
-40
155.52MHz
RMS Phase Jitter (Random)
-50
12kHz to 20MHz = 2.38ps (typical)
-60
Raw Phase Noise Data
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
-180
Phase Noise Result by adding
Sonet Bandpass Filter to raw data
-190
10
100
1k
10k
100k
1M
10M
100M
OFFSET FREQUENCY (HZ)
TYPICAL PHASE NOISE AT 622.08MHZ
0
-10
-20
OC-48 Sonet Bandpass Filter
-30
-40
622.08MHz
-50
RMS Phase Jitter (Random)
Raw Phase Noise Data
-60
12kHz to 20MHz = 2.48ps (typical)
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
Phase Noise Result by adding
Sonet Bandpass Filter to raw data
-180
-190
10
100
1k
10k
100k
1M
10M
100M
OFFSET FREQUENCY (HZ)
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
8
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
PARAMETER MEASUREMENT INFORMATION
2V
SCOPE
nFOUTx
FOUTx
VCC
VCCA
VCCO
,
Qx
,
LVPECL
nFOUTy
FOUTy
nQx
VEE
tsk(o)
-1.3V 0.165V
3.3V OUTPUT LOAD AC TEST CIRCUIT
OUTPUT SKEW
VOH
VREF
nFOUTx
FOUTx
tPW
tPERIOD
VOL
1σ contains 68.26% of all measurements
2σ contains 95.4% of all measurements
3σ contains 99.73% of all measurements
4σ contains 99.99366% of all measurements
6σ contains (100-1.973x10-7)% of all measurements
tPW
odc =
x 100%
tPERIOD
Histogram
Reference Point
(Trigger Edge)
Mean Period
(First edge after trigger)
PERIOD JITTER
OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD
Phase Noise Plot
80%
80%
tR
VSWING
20%
Clock
Outputs
20%
Phase Noise Mask
tF
Offset Frequency
f1
f2
RMS Jitter = Area Under the Masked Phase Noise Plot
OUTPUT RISE/FALL TIME
RMS PHASE JITTER
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
9
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
APPLICATION INFORMATION
POWER SUPPLY FILTERING TECHNIQUES
As in any high speed analog circuitry, the power supply pins
are vulnerable to random noise.The ICS84320I-01 provides
separate power supplies to isolate any high switching
noise from the outputs to the internal PLL.VCC, VCCA, and VCCO
should be individually connected to the power supply
plane through vias, and bypass capacitors should be
used for each pin. To achieve optimum jitter performance,
power supply isolation is required. Figure 2 illustrates how
a 24Ω resistor along with a 10μF and a .01μF bypass
capacitor should be connected to each VCCA pin.
3.3V
VCC
.01μF
.01μF
24Ω
VCCA
10μF
FIGURE 2. POWER SUPPLY FILTERING
RECOMMENDATIONS FOR UNUSED INPUT AND OUTPUT PINS
INPUTS:
OUTPUTS:
CRYSTAL INPUT:
LVCMOS OUTPUT:
For applications not requiring the use of the crystal oscillator All unused LVCMOS output can be left floating. We
input, both XTAL_IN and XTAL_OUT can be left floating. recommend that there is no trace attached.
Though not required, but for additional protection, a 1kΩ
resistor can be tied from XTAL_IN to ground.
LVPECL OUTPUT
All unused LVPECL outputs can be left floating. We
TEST_CLK INPUT:
recommend that there is no trace attached. Both sides of the
For applications not requiring the use of the test clock, it can differential output pair should either be left floating or
be left floating. Though not required, but for additional terminated.
protection, a 1kΩ resistor can be tied from the TEST_CLK to
ground.
SELECT PINS:
All select pins have internal pull-ups and pull-downs;
additional resistance is not required but can be added for
additional protection. A 1kΩ resistor can be used.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
10
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
CRYSTAL INPUT INTERFACE
suitable for most applications. Additional accuracy can be
achieved by adding two small capacitors C1 and C2 as shown in
Figure 3.
A crystal can be characterized for either series or parallel mode
operation.The ICS84320I-01 has a built-in crystal oscillator circuit.
This interface can accept either a series or parallel crystal without
additional components and generate frequencies with accuracy
XTAL_OUT
XTAL_IN
C1
18p
X1
18pF Parallel Crystal
C2
22p
Figure 3. CRYSTAL INPUt INTERFACE
TERMINATION FOR LVPECL OUTPUTS
The clock layout topology shown below is a typical termina- drive 50Ω transmission lines. Matched impedance techniques
tion for LVPECL outputs.The two different layouts mentioned should be used to maximize operating frequency and minimize
are recommended only as guidelines.
signal distortion. Figures 4A and 4B show two different layouts
which are recommended only as guidelines. Other suitable clock
layouts may exist and it would be recommended that the board
designers simulate to guarantee compatibility across all printed
circuit and clock component process variations.
FOUT and nFOUT are low impedance follower outputs that
generate ECL/LVPECL compatible outputs.Therefore, terminat-
ing resistors (DC current path to ground) or current sources
must be used for functionality. These outputs are designed to
3.3V
Z
o = 50Ω
125Ω
125Ω
FOUT
FIN
Zo = 50Ω
Zo = 50Ω
Zo = 50Ω
FOUT
FIN
50Ω
50Ω
VCC - 2V
1
RTT =
Zo
RTT
((VOH + VOL) / (VCC – 2)) – 2
84Ω
84Ω
FIGURE 4A. LVPECL OUTPUT TERMINATION
FIGURE 4B. LVPECL OUTPUT TERMINATION
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
11
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
LAYOUT GUIDELINE
The schematic of the ICS84320I-01 layout example used in
this layout guideline is shown in Figure 5A. The ICS84320I-01
recommended PCB board layout for this example is shown in
Figure 5B. This layout example is used as a general guideline.
The layout in the actual system will depend on the selected
component types, the density of the components, the density
of the traces, and the stack up of the P.C. board.
C1
C2
X1
U1
VCC
R7
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
M5
M6
M7
M8
N0
N1
nc
X_OUT
T_CLK
XTAL_SEL
VCCA
S_LOAD
S_DATA
S_CLOCK
MR
REF_IN
XTAL_SEL
10
VCCA
S_LOAD
S_DATA
S_CLOCK
C11
C16
10u
0.01u
VEE
ICS84320i-01
VCC
R1
125
R3
125
Zo = 50 Ohm
C14
0.1u
TL1
+
-
C15
0.1u
Zo = 50 Ohm
nTL1
VCC=3.3V
R2
84
R4
84
FIGURE 5A. SCHEMATIC OF RECOMMENDED LAYOUT
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
12
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
• The differential 50Ω output traces should have the
same length.
The following component footprints are used in this layout
example:
• Avoid sharp angles on the clock trace.Sharp angle
turns cause the characteristic impedance to change on
the transmission lines.
All the resistors and capacitors are size 0603.
POWER AND GROUNDING
Place the decoupling capacitors C14 and C15, as close as pos-
sible to the power pins. If space allows, placement of the
decoupling capacitor on the component side is preferred. This
can reduce unwanted inductance between the decoupling ca-
pacitor and the power pin caused by the via.
• Keep the clock traces on the same layer.Whenever pos-
sible, avoid placing vias on the clock traces. Placement
of vias on the traces can affect the trace characteristic
impedance and hence degrade signal integrity.
• To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow a separation of at least three trace
widths between the differential clock trace and the other
signal trace.
Maximize the power and ground pad sizes and number of vias
capacitors.This can reduce the inductance between the power
and ground planes and the component power and ground pins.
The RC filter consisting of R7, C11, and C16 should be placed
as close to the VCCA pin as possible.
• Make sure no other signal traces are routed between the
clock trace pair.
CLOCK TRACES AND TERMINATION
• The matching termination resistors should be located as
close to the receiver input pins as possible.
Poor signal integrity can degrade the system performance or
cause system failure. In synchronous high-speed digital systems,
the clock signal is less tolerant to poor signal integrity than other
signals. Any ringing on the rising or falling edge or excessive ring
back can cause system failure. The shape of the trace and the
trace delay might be restricted by the available space on the board
and the component location.While routing the traces, the clock
signal traces should be routed first and should be locked prior to
routing other signal traces.
CRYSTAL
The crystal X1 should be located as close as possible to the pins
25 (XTAL_IN) and 24 (XTAL_OUT).The trace length between the
X1 and U1 should be kept to a minimum to avoid unwanted para-
sitic inductance and capacitance. Other signal traces should not
be routed near the crystal traces.
GND
X1
C1
C2
VCC
VIA
U1
PIN 1
C16
C11
VCCA
R7
Close to the input
pins of the
receiver
R1
R3
R2
R4
C15
TL1
C14
TL1N
TL1, TL21N are 50 Ohm
traces and equal length
FIGURE 5B. PCB BOARD LAYOUT FOR ICS84320I-01
www.icst.com/products/hiperclocks.html
84320AYI-01
REV.A AUGUST 11, 2005
13
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
POWER CONSIDERATIONS
This section provides information on power dissipation and junction temperature for the ICS84320I-01.
Equations and example calculations are also provided.
1. Power Dissipation.
The total power dissipation for the ICS84320I-01 is the sum of the core power plus the power dissipated in the load(s).
The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results.
NOTE: Please refer to Section 3 for details on calculating power dissipated in the load.
•
•
Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 155mA = 537.08mW
Power (outputs)MAX = 30mW/Loaded Output pair
If all outputs are loaded, the total power is 2 * 30mW = 60mW
Total Power_MAX (3.465V, with all outputs switching) = 537.08mW + 60mW = 597.08mW
2. Junction Temperature.
Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the
device.The maximum recommended junction temperature for HiPerClockSTM devices is 125°C.
The equation for Tj is as follows: Tj = θJA * Pd_total + TA
Tj = JunctionTemperature
θJA = Junction-to-AmbientThermal Resistance
Pd_total = Total Device Power Dissipation (example calculation is in section 1 above)
TA = AmbientTemperature
In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a
moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 42.1°C/W perTable 8 below.
Therefore, Tj for an ambient temperature of 85°C with all outputs switching is:
85°C + 0.597W * 42.1°C/W = 110.1°C. This is well below the limit of 125°C.
This calculation is only an example.Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow,
and the type of board (single layer or multi-layer).
TABLE 8. THERMAL RESISTANCE θJA FOR 32-PIN LQFP, FORCED CONVECTION
θJA by Velocity (Linear Feet per Minute)
0
200
55.9°C/W
42.1°C/W
500
50.1°C/W
39.4°C/W
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
67.8°C/W
47.9°C/W
NOTE: Most modern PCB designs use multi-layered boards.The data in the second row pertains to most designs.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
14
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
3. Calculations and Equations.
The purpose of this section is to derive the power dissipated into the load.
LVPECL output driver circuit and termination are shown in Figure 6.
VCCO
Q1
VOUT
R L
50
VCCO - 2V
FIGURE 6. LVPECL DRIVER CIRCUIT AND TERMINATION
To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination
voltage ofV - 2V.
CCO
•
•
For logic high, VOUT = V
= V
– 0.9V
OH_MAX
CCO_MAX
)
= 0.9V
OH_MAX
(V
- V
CCO_MAX
For logic low, V = V
= V
– 1.7V
OUT
OL_MAX
CCO_MAX
)
= 1.7V
OL_MAX
(V
- V
CCO_MAX
Pd_H is power dissipation when the output drives high.
Pd_L is the power dissipation when the output drives low.
))
Pd_H = [(V
– (V
- 2V))/R ] * (V
- V
) = [(2V - (V
- V
/R ] * (V
- V
) =
OH_MAX
CCO_MAX
CCO_MAX
OH_MAX
CCO_MAX
OH_MAX
CCO_MAX
OH_MAX
L
L
[(2V - 0.9V)/50Ω) * 0.9V = 19.8mW
))
Pd_L = [(V
– (V
- 2V))/R ] * (V
- V
) = [(2V - (V
- V
/R ] * (V
- V
) =
OL_MAX
CCO_MAX
CCO_MAX
OL_MAX
CCO_MAX
OL_MAX
CCO_MAX
OL_MAX
L
[(2V - 1.7V)/50Ω) * 1.7V = 10.2mW L
Total Power Dissipation per output pair = Pd_H + Pd_L = 30mW
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
15
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
RELIABILITY INFORMATION
TABLE 9. θJAVS. AIR FLOW TABLE FOR 32 LEAD LQFP
θJA byVelocity (Linear Feet per Minute)
0
200
55.9°C/W
42.1°C/W
500
50.1°C/W
39.4°C/W
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
67.8°C/W
47.9°C/W
NOTE: Most modern PCB designs use multi-layered boards.The data in the second row pertains to most designs.
TRANSISTOR COUNT
The transistor count for ICS84320I-01 is: 3776
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
16
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
PACKAGE OUTLINE - Y SUFFIX FOR 32 LEAD LQFP
TABLE 10. PACKAGE DIMENSIONS
JEDEC VARIATION
ALL DIMENSIONS IN MILLIMETERS
BBA
SYMBOL
MINIMUM
NOMINAL
MAXIMUM
N
A
32
--
--
--
1.60
0.15
1.45
0.45
0.20
A1
A2
b
0.05
1.35
0.30
0.09
1.40
0.37
c
--
D
9.00 BASIC
7.00 BASIC
5.60 Ref.
9.00 BASIC
7.00 BASIC
5.60 Ref.
0.80 BASIC
0.60
D1
D2
E
E1
E2
e
L
0.45
0.75
θ
--
0
°
7°
ccc
--
--
0.10
Reference Document: JEDEC Publication 95, MS-026
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
17
ICS84320I-01
780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL
LVPECL FREQUENCY SYNTHESIZER
Integrated
Circuit
Systems, Inc.
TABLE 11. ORDERING INFORMATION
Part/Order Number
ICS84320AYI-01
Marking
Package
Shipping Packaging
tray
Temperature
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
ICS84320AI01
ICS84320AI01
TBD
32 Lead LQFP
ICS84320AYI-01T
ICS84320AYI-01LF
ICS84320AYI-01LFT
32 Lead LQFP
1000 tape & reel
tray
32 Lead "Lead-Free" LQFP
32 Lead "Lead-Free" LQFP
TBD
1000 tape & reel
NOTE: Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
The aforementioned trademark, HiPerClockS is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use
or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial and industrial applications. Any other applications such as those requiring high reliability or other extraordinary environmental requirements are not
recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product
for use in life support devices or critical medical instruments.
84320AYI-01
www.icst.com/products/hiperclocks.html
REV.A AUGUST 11, 2005
18
相关型号：
©2020 ICPDF网 联系我们和版权申明