M675-02-AA [ICSI]
VOLTAGE CONTROLLED SAW OSCILLATOR; 压控振荡器锯型号: | M675-02-AA |
厂家: | INTEGRATED CIRCUIT SOLUTION INC |
描述: | VOLTAGE CONTROLLED SAW OSCILLATOR |
文件: | 总6页 (文件大小:247K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
P r e l i m i n a r y I n f o r m a t i o n
Integrated
Circuit
Systems, Inc.
M675
VOLTAGE CONTROLLED SAW OSCILLATOR
GENERAL DESCRIPTION
PIN ASSIGNMENT (5 x 7.5mm SMT)
The M675 is a VCSO (Voltage Controlled SAW
Oscillator) frequency source for low-jitter
clock generation. An integrated SAW
(surface acoustic wave) delay line
implements the high-Q VCO (voltage
controlled oscillator) function, which
M675
( T op View)
results in low output phase noise and very low jitter.
The M675-01 is available in a range of center
frequencies from 125 to 175 MHz. The M675-02
provides 500 to 700 MHz. Guaranteed minimum
pull-range of ±100 ppm meets GbE requirements.
(It also fully satisfies ±50 ppm minimum pull-range
specification commonly required.) Industry-standard
Kvco (VCO Gain) provides full replacement compati-
bility. The M675 is well suited for phase-locked loop
implementations, clock and data recovery circuits, and
other timing applications in telecom and optical fiber
networking systems (e.g., SONET/SDH).
Figure 1: Pin Assignment
Sample of Available Output Frequencies
VCSO Center Frequencies1 (MHz)
Applications
M675-01
M675-02
155.5200
622.0800
SONET/SDH
Gigabit Ethernet
FEATURES
◆ Integrated SAW device
156.2500
161.1328
167.3316
625.0000
644.5313
669.3266
Gigabit Ethernet FEC
SONET/SDH FEC
◆ M675-01 output frequencies from 125 to 175 MHz
M675-02 output frequencies from 500 to 700 MHz
(Specify center frequency at time of order)
Table 1: Sample of Available Output Frequencies
◆ Industry-standard Kvco for full compatibility
Note 1: Specify VCSO center frequencies at time of order
◆ Low phase jitter 0.2ps rms typical for the M675-02
(50kHz to 80MHz)
◆ Differential 3.3V LVPECL output
◆ Single 3.3V power supply
◆ Small 5 x 7.5mm SMT (surface mount) package
BLOCK DIAGRAM
M675
SAW Delay Line
FOUT
Phase
Shifter
nFOUT
VIN
CLK_EN
Figure 2: Block Diagram
M675 Datasheet Rev 0.4
Revised 16Nov2004
M675 Voltage Controlled SAW Oscillator
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
M675
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r e l i m i n a r y I n f o r m a t i o n
PIN DESCRIPTIONS
I/O
Input
Number
Name
VIN
Configuration
Description
Frequency control input.
1
Clock enable:
1
Logic 1 enables normal operation.
Logic 0 stops the output clock;
nFOUT is held high, FOUT is held low.
2
CLK_EN
GND
Input
Internal pull-up resistor
3
Ground
Power supply ground connection.
4
5
FOUT
nFOUT
Output
Power
No internal terminator
Clock output pair. Differential LVPECL.
6
VCC
Power supply connection, connect to +3.3V.
Table 2: Pin Descriptions
Note 1: See “Clock Enable Pull-up” in Table 5 (DC Characteristics for M675-01 on pg. 3) and Table 7 (DC Characteristics for M675-02 on pg. 4).
1
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter
Rating
Unit
VI
Inputs
-0.5 to VCC +0.5
V
VO
VCC
TS
Outputs
-0.5 to VCC +0.5
4.6
V
V
Power Supply Voltage
Storage Temperature
-55 to +125
oC
Table 3: Absolute Maximum Ratings
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the
device. These ratings are stress specifications only. Functional operation of product at these conditions
or any conditions beyond those listed in Recommended Conditions of Operation, DC Characteristics, or
AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect product reliability
.
RECOMMENDED CONDITIONS OF OPERATION
Symbol Parameter
Min
Typ
Max
Unit
VCC
Positive Supply Voltage
2.97
3.3
3.63
V
oC
-40
25
TA
Ambient Operating Temperature
+85
Table 4: Recommended Conditions of Operation
M675 Datasheet Rev 0.4
2 of 6
Revised 16Nov2004
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
M675
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r e l i m i n a r y I n f o r m a t i o n
ELECTRICAL SPECIFICATIONS FOR M675-01
DC Characteristics for M675-01
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq.s = 155.52 MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Power Supply VCC Positive Supply Voltage
Pin
Min
2.97
Typ
3.3
Max
3.63
Unit
V
VCC
VIN
85
125
3.3
ICC
VIN
Power Supply Current
Input Control Voltage Range
VIN Input Impedence
Input High Voltage
mA
V
0
Control
Voltage
100
kΩ
V
2
ClockEnable VIH
1
Pull-up
VIL
V + 0.3
cc
0.8
Input Low Voltage
-0.3
V
IIH
IIL
R
Input High Current
Input Low Current
5
µA
µA
kΩ
CLK_EN
-150
51
Internal Pull-up Resistor
pullup
Differential
Outputs
VOH
Output High Voltage
Output Low Voltage
Peak to Peak Output Voltage
Output Current
V
V
- 0.98
V
- 0.75
- 1.63
V
cc
cc
VOL
- 1.95
V
V
cc
cc
FOUT, nFOUT
2
0.450
0.625
0.85
20
VP-P
IOUT
VP-P
mA
Table 5: DC Characteristics for M675-01
Note 1: Internally pulled up to Logic 1 (normal operation) if left unselected.
Note 2: Single-ended measurement. See Figure 3, Output Rise and Fall Time, on pg. 5.
AC Characteristics for M675-01
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 155.52 MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Control Voltage VIN Modulation Bandwidth
Min
Typ
500
Max
Unit Notes
kHz
VIN
Output Center Frequency Range M675-01
125
175
Output
FOUT
APR
MHz
ppm
1
Absolute (Guaranteed) Pull-Range
±100
100
6
fSTAB
LIN
Frequency Stability
Tuning Linearity
ppm p-p At any givin VIN
VIN
Best fit straight line
VIN 0.3 to 3.0
= 0.3 to 3.0V
%
=
V
400
-77
KVCO
VCO Gain
ppm/V
-50
Non-harmonic Spurious
dBc
100Hz Offset
1kHz Offset
-52
-80
Φn
SSB (single sideband)
Phase Noise, offset
from carrier
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps rms
ps rms
%
10kHz Offset
100kHz Offset
1MHz Offset
-112
-136
-146
0.36
0.50
12kHz to 20MHz
50kHz to 80MHz
J(t)
Jitter (rms)
2
45
55
odc
tR
Output Duty Cycle
2
275
275
425
425
Output Rise Time for FOUT, nFOUT
ps
ps
20% to 80%
20% to 80%
2
tF
Output Fall Time for FOUT, nFOUT
Table 6: AC Characteristics for M675-01
Note 1: Also fully meets 50 ppm minimum pull-range specification that is commonly required.
Note 2: See Parameter Measurement Information on pg. 5.
M675 Datasheet Rev 0.4
3 of 6
Revised 16Nov2004
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
M675
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r e l i m i n a r y I n f o r m a t i o n
ELECTRICAL SPECIFICATIONS FOR M675-02
DC Characteristics for M675-02
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 622.08 MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Power Supply VCC Positive Supply Voltage
Pin
Min
2.97
Typ
3.3
Max
3.63
Unit
V
VCC
VIN
85
125
3.3
ICC
VIN
Power Supply Current
Input Control Voltage Range
VIN Input Impedence
Input High Voltage
mA
V
0
Control
Voltage
100
kΩ
V
2
ClockEnable VIH
1
Pull-up
VIL
V + 0.3
cc
0.8
Input Low Voltage
-0.3
V
IIH
IIL
R
Input High Current
Input Low Current
5
µA
µA
kΩ
CLK_EN
-150
51
Internal Pull-up Resistor
pullup
Differential
Outputs
VOH
Output High Voltage
Output Low Voltage
Peak to Peak Output Voltage
Output Current
V
V
- 0.98
V
- 0.75
- 1.63
V
cc
cc
VOL
- 1.95
V
V
cc
cc
FOUT, nFOUT
2
0.450
0.625
0.85
20
VP-P
IOUT
VP-P
mA
Table 7: DC Characteristics for M675-02
Note 1: Internally pulled up to Logic 1 (normal operation) if left unselected.
Note 2: Single-ended measurement. See Figure 3, Output Rise and Fall Time, on pg. 5.
AC Characteristics for M675-02
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq. = 622.08 MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Control Voltage VIN Modulation Bandwidth
Min
Typ
500
Max
Unit Notes
kHz
VIN
Output Center Frequency Range M675-02
500
700
Output
FOUT
APR
MHz
ppm
1
Absolute (Guaranteed) Pull-Range
±100
100
6
fSTAB
LIN
Frequency Stability
Tuning Linearity
ppm p-p At any givin VIN
VIN
Best fit straight line
VIN 0.3 to 3.0
= 0.3 to 3.0V
%
=
V
400
-77
KVCO
VCO Gain
ppm/V
-50
Non-harmonic Spurious
dBc
100Hz Offset
1kHz Offset
-48
-75
Φn
SSB (single sideband)
Phase Noise, offset
from carrier
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps rms
ps rms
%
10kHz Offset
100kHz Offset
1MHz Offset
-99
-124
-142
0.30
0.18
12kHz to 20MHz
50kHz to 80MHz
J(t)
Jitter (rms)
2
45
55
odc
tR
Output Duty Cycle
2
275
275
400
400
Output Rise Time for FOUT, nFOUT
ps
ps
20% to 80%
20% to 80%
2
tF
Output Fall Time for FOUT, nFOUT
Table 8: AC Characteristics for M675-02
Note 1: Also fully meets 50 ppm minimum pull-range specification that is commonly required.
Note 2: See Parameter Measurement Information on pg. 5.
M675 Datasheet Rev 0.4
4 of 6
Revised 16Nov2004
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
M675
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r e l i m i n a r y I n f o r m a t i o n
PARAMETER MEASUREMENT INFORMATION
Output Rise and Fall Time
Output Duty Cycle
nFOUT
80%
80%
V
P-P
20%
t
F
20%
Clock
Outputs
FOUT
t
R
t
PW
(Output Pulse Width)
t
PERIOD
t
PW
Figure 3: Output Rise and Fall Time
odc =
t
PERIOD
Figure 4: Output Duty Cycle
DEVICE PACKAGE - 5 x 7.5mm SMT (Surface Mount) Package
Mechanical Dimensions:
-02-AA
Dimensions are in mm;
dimensions in [ ] are in inches
Unless otherwise specified, all
dimensions are ±0.13 [0.005]
Figure 5: Device Package - 5 x 7.5mm SMT (Surface Mount) Package
M675 Datasheet Rev 0.4
5 of 6
Revised 16Nov2004
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
P r e l i m i n a r y I n f o r m a t i o n
M675
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
ORDERING INFORMATION
Part Numbering Scheme
M675-01 Standard Output Frequencies & Order Codes
153.6000 BO
155.5200 BA
156.2500 BB
156.8324 BC
161.1328 BD
164.3555 BM
166.6286 BE
167.2820 BF
167.3280 BG
167.3316 BH
167.7097 BI
168.0400 BJ
172.6423 BK
173.3708 BL
Part Number:
MM667850-01y-xx
Device Number
Variant
-01 = Output Frequencies 125 - 175 MHz
-02 = Output Frequencies 500 - 700 MHz
Output Frequency Order Code
See Tables 10 and 11 at right for frequency order codes.
Consult ICS for other frequencies and order codes.
Figure 6: Part Numbering Scheme
Example Order Numbers
Table 10: M675-01 Standard Output Frequencies & Order Codes
For Output Order Part # For Output Order Part #
M675-02 Standard Output Frequencies & Order Codes
M675-01-Bx
M675-02-Ax
Frequencies
155.5200
156.2500
161.1328
167.3316
Frequencies
614.4000 AO
622.0800 AA
625.0000 AB
627.3296 AC
644.5313 AD
657.4219 AM
666.5143 AE
669.1281 AF
669.3120 AG
669.3266 AH
670.8386 AI
672.1600 AJ
690.5692 AK
693.4830 AL
M675-01-BA
M675-01-BB
M675-01-BD
M675-01-BH
M675-02-AA
M675-02-AB
M675-02-AD
M675-02-AH
622.0800
625.0000
644.5313
669.3266
Table 9: Example Order Numbers
Table 11: M675-02 Standard Output Frequencies & Order Codes
Consult ICS for the availability of other frequencies
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
M675 Datasheet Rev 0.4
6 of 6
Revised 16Nov2004
Integrated Circuit Systems, Inc. ● Networking & Communications ● www.icst.com ● tel (508) 852-5400
相关型号:
©2020 ICPDF网 联系我们和版权申明