70824L20G [IDT]
PGA-84, Tray;型号: | 70824L20G |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | PGA-84, Tray |
文件: | 总21页 (文件大小:191K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HIGH SPEED 64K (4K X 16 BIT)
SEQUENTIAL ACCESS
IDT70824S/L
RANDOM ACCESS MEMORY (SARAM™)
Features
◆
◆
High-speed access
Compatible with Intel BMIC and 82430 PCI Set
Width and Depth Expandable
Sequential side
– Address based flags for buffer control
◆
– Military:35/45ns(max.)
◆
– Commercial:20/25/35/45ns(max.)
Low-power operation
◆
– IDT70824S
– Pointer logic supports up to two internal buffers
Battery backup operation - 2V data retention
TTL-compatible, single 5V (+10%) power supply
Available in 80-pin TQFP and 84-pin PGA
Military product compliant to MIL-PRF-38535 QML
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
◆
Active:775mW(typ.)
Standby: 5mW (typ.)
– IDT70824L
◆
◆
◆
Active:775mW(typ.)
Standby: 1mW (typ.)
◆
◆
™
4Kx16SequentialAccess RandomAccess Memory (SARAM )
– Sequential Access from one port and standard Random
Access from the other port
– Separate upper-byte and lower-byte control of the
RandomAccessPort
High speed operation
– 20ns tAA for random access port
– 20ns tCD for sequential port
Description
TheIDT70824isahigh-speed4Kx16-BitSequentialAccessRandom
AccessMemory(SARAM).TheSARAMoffersasingle-chipsolutionto
bufferdatasequentiallyononeport,andbeaccessedrandomly(asyn-
chronously) through the other port. The device has a Dual-Port RAM
based architecture with a standard SRAM interface for the random
(asynchronous) access port, and a clocked interface with counter se-
◆
◆
– 25nsclockcycletime
Architecture based on Dual-Port RAM cells
FunctionalBlockDiagram
12
RST
SCLK
CNTEN
A0-11
CE
OE
Random
Access
Port
Sequential
SOE
Access
R/W
SSTRT
SSTRT
SCE
SR/W
SLD
1
Port
Controls
LB LSB
2
Controls
UB MSB
CMD
4K X 16
Memory
Array
16
16
16
Data
R
Reg.
12
Data
L
I/O0-15
SI/O0-15
,
12
Addr
L
Addr
R
12
RST
12
Pointer/
Counter
12
12
Start Address for Buffer #1
End Address for Buffer #1
Start Address for Buffer #2
End Address for Buffer #2
Flow Control Buffer
12
EOB
1
2
COMPARATOR
EOB
Flag Status
3099 drw 01
JANUARY 2009
1
©2009IntegratedDeviceTechnology,Inc.
DSC-3099/6
6.07
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
The IDT70824is packagedina 80-pinThinQuadFlatpack(TQFP)
or84-pinPinGridArray(PGA).Militarygradeproductis manufactured
incompliancewiththelatestrevisionofMIL-PRF-38535QML,makingit
ideallysuitedtomilitarytemperatureapplicationsdemandingthehighest
levelofperformanceandreliability.
quencingforthesequential(synchronous)accessport.
FabricatedusingCMOShigh-performancetechnology,thismemory
devicetypicallyoperatesonlessthan775mWofpoweratmaximumhigh-
speed clock-to-data and Random Access. An automatic power down
feature,controlledbyCE,permitstheon-chipcircuitryofeachporttoenter
a very low standby power mode.
PinConfigurations(1,2,3)
INDEX
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
60
SI/O
SI/O
GND
N/C
SCE
SR/W
RST
SLD
SSTRT
SSTRT
GND
GND
CNTEN
SOE
SCLK
GND
1
0
A
A
A9
A8
A7
A6
A5
A4
A3
A2
V
V
A
A
CMD
CE
LB
11
10
1
59
58
57
56
55
54
2
3
4
5
6
7
8
53
52
51
2
9
IDT70824PF
PN80-1(4)
1
10
11
12
13
14
15
16
17
18
19
20
50
49
CC
CC
80-Pin TQFP
Top View(5)
48
47
1
0
46
45
44
EOB
EOB
2
UB
R/W
1
43
42
VCC
41 OE
I/O
0
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
,
3099 drw 02
63
61
V
60
58
55
54
48
46
45
42
51
11
10
09
08
07
06
05
04
03
02
01
EOB
1
SSTRT2
NC
SR/W
I/O
1
CC
CNTEN
GND
GND
GND NC
66
67
64
62
59
56
49
47
44
43
40
50
SI/O
0
SI/O
1
SI/O
I/O
2
EOB
2
SOE RST
SCE
NC
SLD
3
I/O
0
65
57
53
41
39
52
SSTRT1
I/O
3
GND
SCLK GND
SI/O
2
7
VCC
69
68
38
37
I/O
4
V
CC
SI/O
4
SI/O
5
72
71
73
33
35
34
I/O
7
I/O
6
SI/O8
SI/O
GND
74
GND
IDT70824G
G84-3(4)
75
70
32
31
36
I/O
9
I/O
5
I/O
8
SI/O9
SI/O10
29
SI/O
6
84-Pin PGA
Top View(5)
76
77
78
28
30
I/O10 I/O11
V
CC
SI/O12
V
CC SI/O11
79 80
I/O12
81
I/O14
82
26 27
I/O13
83
SI/O14
23
SI/O13
25
7
11
V
12
CMD
CC
A2
NC
NC SI/O15
1
2
4
5
8
9
10
V
14
17
20
22
24
OE
LB
A
4
A
7
CC
A
10
I/O15 GND
A
0
1
GND GND
84
3
6
15
13
16
18
19
21
NC R/W
UB
CE
A8
A
A
5
A3
A
6
A
9
A11
,
A
B
C
D
E
F
G
H
J
K
L
Pin 1
Designator
3099 drw 03
NOTES:
1. All VCC pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. PN80-1 package body is approximately 14mm x 14mm x 1.4mm.
G84-3 package body is approximately 1.12 in x 1.12 in x .16 in.
4. This package code is used to reference the package diagram.
5. This text does not indicate orientation of the actual part-marking.
2
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Pin Descriptions: Random Access Port(1)
SYMBOL
-A11
I/O
CE
NAME
I/O
DESCRIPTION
A0
Address Lines
I
I
I
Address inputs to access the 4096-word (16-Bit) memory array.
0-I/O15
Inputs/Outputs
Chip Enable
Random access data inputs/outputs for 16-Bit wide data.
When CE is LOW, the random access port is enabled. When CE is HIGH, the random access port is disabled
into power-down mode and the I/O outputs are in the High-impedance state. All data is retained during CE =
VIH, unless it is altered by the sequential port CE and CMD may not be LOW at the same time.
Control Register Enable
Read/Write Enable
Output Enable
I
I
When CMD is LOW, address lines A
0
-A
2
, R/W, and inputs and outputs I/O0-I/O12, are used to access the
CMD
control register, the flag register and the start and end of buffer registers. CMD and CE may not be LOW at the
same time.
R/W
If CE is LOW and CMD is HIGH, data is written into the array when R/W is LOW and read out of the array when
R/W is HIGH. If CE is HIGH and CMD is LOW, R/W is used to access the buffer command registers. CE and
CMD may not be LOW at the same time.
I
I
When OE is LOW and R/W is HIGH, I/O
0
-I/O15 outputs are enabled. When OE is HIGH, the I/O outputs are in
OE
the High-impedance state.
Lower Byte, Upper Byte
Enables
When LB is LOW, I/O -I/O
0
7
are accessible for read and write operations. When LB is HIGH, I/O
0-I/O7 are tri-
-I/O15 in the same manner and
LB, UB
stated and blocked during read and write operations. UB controls access for I/O
8
is asynchronous
from LB.
V
CC
Power Supply
Ground
I
I
Seven +5 power supply pins. All VCC pins must be connected to the same +5V VCC supply.
Ten ground pins. All ground pins must be connected to the same ground supply.
GND
3099 tbl 01
Pin Descriptions: Sequential Access Port(1)
SYMBOL
SI/O0-15
SCLK
NAME
I/O DESCRIPTION
Inputs/Outputs
Clock
I/O Sequential data inputs/outputs for 16-bit wide data.
I
SI/O0-SI/O15,SCE, SR/W, and SLD are registered on the LOW-to-HIGH transition of SCLK. Also, the sequential
access port address pointer increments by 1 on each LOW-TO-HIGH transition of SCLK when CNTEN is LOW.
Chip Enable
I
When SCE is LOW, the sequential access port is enabled on the LOW-to-HIGHtransition of SCLK. When SCE
is HIGH, the sequential access port is disabled into powered-down mode on the LOW-to-HIGH transition of
SCLK, and the SI/O outputs are in the High-impedance state. All data is retained, unless altered by the random
access port.
SCE
Counter Enable
I
I
When CNTEN is LOW, the address pointer increments on the LOW-to-HIGH transition of SCLK. This function is
independent of CE.
CNTEN
SR/W
Read/Write Enable
When SR/W and SCE are LOW, a write cycle is initiated on the LOW-to-HIGH transition of SCLK. When SR/W is
HIGH, and SCE and SOE are LOW, a read cycle is initiated on the LOW-to-HIGH transition of SCLK. Termination
of a write cycle is done on the LOW-to-HIGH transition of SCLK if SR/W or SCE is HIGH.
Address Pointer Load Control
I
When SLD is sampled LOW, there is an internal delay of one cycle before the address pointer changes. When
SLD
SLD is LOW, data on the inputs SI/O0-SI/O11 is loaded into a data-in register on the LOW-to-HIGH transition of
SCLK. On the Cycle following SLD, the address pointer charges to the address location contained in the data-
in register. SSTRT and SSTRT may not be LOW while SLD is LOW or during the cycle following SLD.
1
2
Load Start of Address
Register
I
When SSTRT or SSTRT is LOW, the start of address register #1 or #2 is loaded into the address pointer on
1
2
SSTRT1
2
SSTRT
,
the LOW-to-HIGH transition of SCLK. The start addresses are stored in internal registers. SSTRT
1
and SSTRT
2
may not be LOW while SLD is LOW or during the cycle following SLD.
End of Buffer Flag
O
EOB1
2
EOB
,
EOB
of buffer registers. The flags can be cleared by either asserting RST LOW or by writing zero into Bit 0 and/or
Bit 1 of the control register at address 101. EOB and EOB are dependent on separate internal registers, and
therefore separate match addresses.
1
or EOB2 is output low when the address pointer is incremented to match the address stored in the end
1
2
Output Enable
Reset
I
I
SOE
SOE controls the data outputs and is independent of SCLK. When SOE is LOW, output buffers and the
sequentially addressed data is output. When SOE is HIGH, the SI/O output bus is in the High-impedance state.
SOE is asynchronous to SCLK.
When RST is LOW, all internal registers are set to their default state, the address pointer is set to zero and the
RST
EOB
1
and EOB flags are set HIGH. RST is asynchronous to SCLK.
2
3099 tbl 02
NOTE:
1. "I/O" is bidirectional Input and Output. "I" is Input and "O" is Output.
6.42
3
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
AbsoluteMaximumRatings(1)
RecommendedOperating
TemperatureandSupplyVoltage
Symbol
Rating
Commercial
& Industrial
Military
Unit
Grade
GND
Vcc
(2)
Ambient Temperature
-55OC to +125OC
0OC to +70OC
V
TERM
Terminal Voltage
with Respect
to GND
-0.5 to +7.0
-0.5 to +7.0
V
Military
0V
0V
0V
5.0V
+
+
+
10%
T
BIAS
Temperature
Under Bias
-55 to +125
-65 to +150
50
-65 to +135
-65 to +150
50
oC
oC
Commercial
Industrial
5.0V
5.0V
10%
-40OC to +85OC
10%
Storage
Temperature
TSTG
3099 tbl 04
NOTES:
1. This is the parameter TA. This is the "instant on" case temperature.
2. Industrial temperature: for specific speeds, packages and powers contact
your sales office.
DC Output
Current
mA
IOUT
3099 tbl 03
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VTERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns
maximum, and is limited to < 20mA for the period of VTERM > Vcc + 10%.
RecommendedDCOperating
Conditions
Symbol
Parameter
Supply Voltage
GND Ground
Min.
Typ. Max. Unit
VCC
4.5
5.0
5.5
0
V
V
V
0
0
V
IH
Input High Voltage
Input Low Voltage
2.2
6.0(2)
0.8
____
Capacitance
VIL
-0.5(1)
V
(TA = +25°C, f = 1.0mhz, TQFP only)
____
Symbol
Parameter
Input Capacitance
Output Capacitance
Conditions(2)
IN = 3dV
OUT = 3dV
Max. Unit
3099 tbl 05
NOTES:
CIN
V
9
pF
1. VIL > -1.5V for pulse width less than 10ns.
2. VTERM must not exceed Vcc + 10%.
COUT
V
10
pF
3099 tbl 06
NOTES:
1. This parameter is determined by device characterization, but is not
production tested.
2. 3dV references the interpolated capacitance when the input and output
signals switch from 0V to 3V or from 3V to 0V.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VCC = 5.0V ± 10%)
70824S
70824L
Symbol
|ILI
|ILO
Parameter
Input Leakage Current
Output Leakage Current
Output Low Voltage
Test Conditions
CC = 5.5V, VIN = 0V to VCC
Min.
Max.
5
Min.
Max.
Unit
µA
µA
V
___
___
|
V
1
1
___
___
___
___
|
V
OUT = 0V to VCC
OL = +4mA
OH = -4mA
5
VOL
I
0.4
0.4
___
___
VOH
Output High Voltage
I
2.4
2.4
V
3099 tbl 07
4
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(1,2,8)(VCC = 5.0V ± 10%)
70824X20
70824X25
70824X35
Com'l &
Military
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Test Condition
Version
COM'L
Typ.(2)
Max.
Typ.(2 )
Max.
Typ.(2 )
Max.
Typ.(2)
Max.
Unit
ICC
Dynamic Operating
Current
(Both Ports Active)
S
L
180
180
380
330
170
170
360
310
160
160
340
290
155
155
340
290
mA
CE
L
and CE
R
= VIL
,
Outputs Disabled
SCE = VIL(5)
____
____
____
____
____
____
____
____
(3 )
MIL &
IND
S
L
160
160
400
340
155
155
400
340
f = fMAX
(7 )
I
SB1
Standby Current
(Both Ports - TTL
Level Inputs)
COM'L
S
L
25
25
70
50
25
25
70
50
20
20
70
50
16
16
70
50
mA
mA
mA
mA
SCE and CE = VIH
CMD = VIH
(3 )
f = fMAX
____
____
____
____
____
____
____
____
MIL &
IND
S
L
20
20
85
65
16
16
85
65
ISB2
Standby Current
(One Port - TTL
Level Inputs)
COM'L
S
L
115
115
260
230
105
105
250
220
95
95
240
210
90
90
240
210
CE or SCE = VIH
Active Port Outputs Disabled,
(3 )
f=fMAX
____
____
____
____
____
____
____
____
MIL &
IND
S
L
95
95
290
250
90
90
290
250
ISB3
Full Standby Current
Both Ports CE and
COM'L
S
L
1.0
0.2
15
5
1.0
0.2
15
5
1.0
0.2
15
5
1.0
0.2
15
5
(6)
(Both Ports
-
SCE > VCC - 0.2V
CMOS Level Inputs)
VIN > VCC - 0.2V or
V
IN < 0.2V,
MIL &
IND
S
L
1.0
0.2
30
10
1.0
0.2
30
10
____
____
____
____
____
____
____
____
f = 0(4)
ISB4
Full Standby Current
(One Port -
CMOS Level Inputs)
One Port CE or
COM'L
S
L
110
110
240
200
100
100
230
190
90
90
220
180
85
85
220
180
(6,7)
SCE > VCC - 0.2V
Outputs Disabled (Active Port)
____
____
____
____
____
____
____
____
(3 )
MIL &
IND
S
L
90
90
260
215
85
85
260
215
f = fMAX
V
IN > VCC - 0.2V or VIN < 0.2V
3099 tbl 08
NOTES
1. 'X' in part number indicates power rating (S or L).
2. VCC = 5V, TA = +25°C; guaranteed by device characterization but not production tested.
3. At f = fMAX, address, control lines (except Output Enable), and SCLK are cycling at the maximum frequency read cycle of 1/tRC.
4. f = 0 means no address or control lines change.
5. SCE may transition, but is Low (SCE=VIL) when clocked in by SCLK.
6. SCE may be - 0.2V, after it is clocked in, since SCLK=VIH must be clocked in prior to powerdown.
7. If one port is enabled (either CE or SCE = LOW) then the other port is disabled (SCE or CE = HIGH, respectively). CMOS HIGH > Vcc - 0.2V and LOW < 0.2V, and
TTL HIGH = VIH and LOW = VIL.
8. Industrial temperature: for specific speeds, packages and powers contact your sales office.
Data Retention Characteristics Over All Temperature Ranges
(L Version Only) (VLC < 0.2V, VHC > VCC - 0.2V)
Symbol
Parameter
Test Condition
Min.
Typ.(1)
Max.
Unit
V
___
___
V
DR
VCC for Data Retention
VCC = 2V
2.0
___
I
CCDR
Data Retention Current
µA
CE = VHC
IN = VHC or = VLC
MIL. & IND.
COM'L.
100
4000
___
___
(2)
V
100
1500
(3)
CDR
SCE = VHC(4) when SCLK = u
CMD > VHC
___
___
t
Chip Deselect to Data Retention Time
Operation Recovery Time
V
(3)
___
___
tR
t
RC
V
3099 tbl 09
NOTES :
1. TA = +25°C, VCC = 2V; guaranteed by device characterization but not production tested.
2. tRC = Read Cycle Time
3. This parameter is guaranteed by device characterization, but is not production tested.
4. To initiate data retention, SCE = VIH must be clocked in.
6.42
5
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
DataRetentionPowerDown/UpWaveform(RandomandSequentialPort)(1,2)
DATA RETENTION MODE
VCC
4.5V
≥
VDR 2V
4.5V
tCDR
tR
VDR
VIH
CE
VIH
SCLK
SCE
tPD
tPU
ICC
3099 drw 04
I
SB
ISB
NOTES :
1. SCE is synchronized to the sequential clock input.
2. CMD > VCC - 0.2V.
5V
5V
893Ω
893Ω
DATAOUT
DATAOUT
30pF
347Ω
5pF*
347Ω
3099 drw 06
3099 drw 05
Figure 1. AC Output Test Load
Figure 2. Output Test Load (for tCLZ, tBLZ, tOLZ, tCHZ, tBHZ,
tOHZ,tWHZ, tCKHZ, and tCKLZ)
(*Including scope and jig.)
8
7
6
AC Test Conditions
Input Pulse Levels
GND to 3.0V
3ns Max.
1.5V
Input Rise/Fall Times
tAA/tCD/tEB
(Typical, ns)
5
4
3
2
1
Input Timing Reference Levels
Output Reference Levels
Output Load
10pF is the I/O
capacitance of
this device, and
30pF is the AC
Test Load
1.5V
Figures 1,2 and 3
3099 tbl 10
capacitance.
-1
-2
-3
20 40 60 80 100 120 140 160 180 200
,
3099 drw 07
CAPACITANCE (pF)
Figure 3. Lumped Capacitance Load Typical Derating Curve
6
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Truth Table I: Random Access Read and Write(1,2)
Inputs/Outputs
R/W
H
H
H
L
I/O
0
-I/O
7
I/O8-I/O15
MODE
CE
L
CMD
H
OE
L
LB
L
UB
L
DATAOUT
DATAOUT
High-Z
DATAIN
DATAIN
High-Z
DATAOUT Read both Bytes.
L
H
L
L
H
L
High-Z
Read lower Byte only.
L
H
L
H
L
DATAOUT Read upper Byte only.
(3)
L
H
H
L
DATAIN
High-Z
DATAIN
High-Z
High-Z
High-Z
DATAIN
DATAOUT
Write to both Bytes.
(3)
L
H
L
H
L
H
L
Write to lower Byte only.
Write to upper Byte only.
(3)
L
H
L
H
X
H
X
H
X
X
H
H
L
H
X
H
X
L
X
X
H
High-Z
Both Bytes deselected and powered down.
Outputs disabled but not powered down.
Both Bytes deselected but not powered down.
H
High-Z
L
H
High-Z
(3)
(4)
(4)
H
H
L
H
L
L
L
DATAIN
DATAOUT
Write I/O0-I/O11 to the Buffer Command Register.
(4)
(4)
L
L
L
H
Read contents of the Buffer Command Register
via I/O -I/O12.
0
3099 tbl 11
NOTES:
1. H = VIH, L = VIL, X = Don't Care, and HIGH-Z = High-impedance.
2. RST, SCE, CNTEN, SR/W, SLD, SSTRT1, SSTRT2, SCLK, SI/O0-SI/O15, EOB1, EOB2, and SOE are unrelated to the random access port control and operation.
3. If OE = VIL during write, tWHZ must be added to the tWP or tCW write pulse width to allow the bus to float prior to being driven.
4. Byte operations to control register using UB and LB separately are also allowed.
Truth Table II: Sequential Read(1,2,3,6,8)
Inputs/Outputs
SCLK
SR/W
H
SI/O
[EOB
[EOB1 - 1
[EOB
[EOB2 - 1
High-Z
MODE
Counter Advanced Sequential Read with EOB
Non-Counter Advanced Sequential Read, without EOB
Counter Advanced Sequential Read with EOB reched.
Non-Counter Advanced Sequential Read without EOB
Counter Advanced Sequential Non-Read with EOB
SCE
L
CNTEN
EOB
1
EOB
2
SOE
L
L
H
L
H
L
LOW LAST
LAST LAST
1
]
1 reached.
↑
↑
↑
↑
↑
L
H
L
]
1
reached
L
H
LAST
LAST LAST
LOW LOW
LOW
L
2]
2
L
H
L
]
2
reached
L
H
H
1
and EOB2 reached
3099 tbl 12
Truth Table III: Sequential Write(1,2,3,4,5,6,7,8)
Inputs/Outputs
SCLK
SR/W
L
SI/O
SI/OIN Non-Counter Advanced Sequential Write, without EOB
SI/OIN Counter Advanced Sequential Write with EOB and EOB
MODE
SCE
L
CNTEN
EOB
LAST LAST
LOW LOW
1
EOB
2
SOE
H
H
L
H
L
1
or EOB
2 reached.
↑
L
L
H
1
2
reached.
↑
H
X
LAST LAST
NEXT NEXT
X
High-Z No Write or Read due to Sequential port Deselect. No counter advance.
High-Z No Write or Read due to Sequential port Deselect. Counter does advance.
↑
↑
H
X
X
3099 tbl 13
NOTES:
1. H = VIH, L = VIL, X = Don't Care, and HIGH-Z = High-impedance. LOW = VOL.
2. RST, SLD, SSTRT1, SSTRT2 are continuously HIGH during a sequential write access, other than pointer access operations.
3. CE, OE, R/W, CMD, LB, UB, and I/O0-I/O15 are unrelated to the sequential port control and operation except for CMD which must not be used concurrently with the
sequential port operation (due to the counter and register control). CMD should be HIGH (CMD = VIH) during sequential port access.
4. SOE must be HIGH (SOE=VIH) prior to write conditions only if the previous cycle is a read cycle, since the data being written must be an input at the rising edge
of the clock during the cycle in which SR/W = VIL.
5. SI/OIN refers to SI/O0-SI/O15 inputs.
6. "LAST" refers to the previous value still being output, no change.
7. Termination of a write is done on the LOW-to-HIGH transition of SCLK if SR/W or SCE is HIGH.
8. When CLKEN=LOW, the address is incremented on the next rising edge before any operation takes place. See the diagrams called "Sequential Counter Enable Cycle
after Reset, Read (and write) Cycle".
6.42
7
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
TruthTable:SequentialAddressPointerOperations(1,2,3,4,5)
Inputs/Outputs
SCLK
MODE
Non-Counter Advanced Sequential Write, without EOB
Counter Advanced Sequential Write with EOB and EOB
No Write or Read due to Sequential port Deselect. No counter advance.
SLD
H
SSTRT
1
SSTRT
1
SOE
X
L
H
H
H
L
1
or EOB
2 reached.
↑
↑
↑
H
X
1
2
reached.
(6)
L
H
H
3099 tbl 14
NOTES:
1. H = VIH, L = VIL, X = Don't Care, and High-Z = High-impedance.
2. RST is continuously HIGH. The conditions of SCE CNTEN, and SR/W are unrelated to the sequential address pointer operations.
3. CE, OE, R/W, LB, UB, and I/O0-I/O15 are unrelated to the sequential port control and operation, except for CMD which must not be used concurrently with the sequential
port operation (due to the counter and register control). CMD should be HIGH (CMD = VIH) during sequential port access.
4. Address pointer can also change when it reaches an end of buffer address. See Flow Control Bits table.
5. When SLD is sampled LOW, there is an internal delay of one cycle before the address pointer changes. The state of CNTEN is ignored and the address is not incremented
during the two cycles.
6. SOE may be LOW with SCE deselect or in the write mode using SR/W.
Address Pointer Load Control (SLD)
InSLDmode,thereisaninternaldelayofonecyclebeforetheaddress changestotheaddresslocationcontainedinthedata-inregister.SSTRT1,
pointerchangesinthecyclefollowingSLD.WhenSLDisLOW,dataon SSTRT2maynotbelowwhileSLDisLOW,orduringthecyclefollowing
theinputsSI/O0-SI/O11 isloadedintoadata-inregisterontheLOW-to- SLD.TheSSTRT1andSSTRT2requireonlyoneclockcycle,sincethese
HIGHtransitionofSCLK.OnthecyclefollowingSLD,theaddresspointer addresses are pre-loaded in the registers already.
SLDMode(1)
SLD
SCLK(1)
B
A
C
SI/O0-11
ADDRIN
DATAOUT
SSTRT(1 or 2)
3099 drw 08
NOTE:
1. At SCLK edge (A), SI/O0-SI/O11 data is loaded into a data-in register. At edge (B), contents of the data-in register are loaded into the address pointer (i.e.
address pointer changes). At SCLK edge (A), SSTRT1 and SSTRT2 must be HIGH to ensure for proper sequential address pointer loading. At SCLK edge (B),
SLD and SSTRT1,2 must be HIGH to ensure for proper sequential address pointer loading. For SSTRT1 or SSTRT2, the data to be read will be ready for edge
(B), while data will not be ready at edge (B) when SLD is used, but will be ready at edge (C).
Sequential Load of Address into Pointer/Counter(1)
15
14
13
12
11 -------------------------------------------------------------------------------------------------- 0
Address Loaded into Pointer
LSB SI/O BITS
MSB
H
H
H
L
3099 drw 09
NOTE:
1. "H" = VIH and "L" = VIL for the SI/O intput state.
8
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Reset (RST)
Register
Contents
0
SettingRSTLOWresetsthecontrolstateoftheSARAM.RSTfunctions
asynchronouslyofSCLK(i.e.notregistered).Thedefaultstatesaftera
resetoperationaredisplayedintheadjacentchart.
Address
Cleared to HIGH state
BUFFER CHAINING
EOB Flags
Buffer Flow Mode
Start Address Buffer #1
End Address Buffer #1
0
(1)
4095 (4K)
(1)
Start Address Buffer #2
Cleared (set at invalid points)
Cleared (set at invalid points)
SCE = VIH, SR/W = VIL
(1)
End Address Buffer #2
Registered State
3099 tbl 15
NOTE:
1. Start address and End of address for Buffer #2 and the Flow Control for
both Buffer #1 and #2, must be programmed as described in the "Buffer
Command Mode" section.
Buffer Command Mode (CMD)
alsoallowsreadingandclearingthestatusoftheEOBflags.Sevendifferent
CMD cases are available dependingonthe conditions ofA0-A2 andR/
W.AddressbitsA3-A11anddataI/ObitsI/O12-I/O15arenotusedduring
thisoperation.
Buffer Command Mode (CMD) allows the random access port to
controlthestateofthetwobuffers.AddresspinsA0-A2andI/OpinsI/O0-
I/O11areusedtoaccessthestartofbufferandtheendofbufferaddresses
andtosettheflowcontrolmodeofeachbuffer.TheBufferCommandMode
Random Access Port CMD Mode(1)
Case #
A
2
-A
0
R/W
0 (1)
0 (1)
0 (1)
0 (1)
0 (1)
0
DESCRIPTIONS
1
2
3
4
5
6
7
8
000
001
Write (read) the start address of Buffer #1 through I/O
Write (read) the end address of Buffer #1 through I/O
Write (read) the start address of Buffer #2 through I/O
Write (read) the end address of Buffer #2 through I/O
Write (read) flow control register.
Write only - clear EOB and/or EOB
0
-I/O11
.
0
-I/O11
.
010
0
-I/O11
.
011
0
-I/O11
.
100
101
1
2 flag.
101
1
Read only - flag status register.
(Reserved)
110/111
(X)
3099 tbl 16
NOTE:
1. R/W input "0(1)" indicates a write(0) or read(1) occurring with the same address input.
Cases 1 through 4: Start and End of Buffer Register Description(1,2)
15
14
13
12
11 -------------------------------------------------------------------------------------------------- 0
Address Loaded into Buffer
LSB I/O BITS
MSB
H
H
H
L
3099 drw 10
NOTES:
1. "H" = VOH for I/O in the output state and "Don't Cares" for I/O in the input state. "L" = VIL for I/O in the input state.
2. A write into the buffer occurs when R/W = VIL and a read when R/W = VIH. EOB1/SOB1 and EOB2/SOB2 are chosen through address A0-A2 while CMD = VIL and
CE = VIH.
Case 5: Buffer Flow Modes
WithintheSARAM,theusercandesignateoneoftwobufferflowmodes
thecorrespondingEOBflagandcontinuesfromthestartaddressofthe
otherbuffer.InSTOPmode,theaddresspointerstopsincrementingafter
itreachestheendofthebuffer.Thereisnolinearormaskmodeavailable.
foreachbuffer.Eachbufferflowmodedefinesauniquesetofactionsfor
thesequentialportaddresspointerandEOB flags.InBUFFERCHAIN-
INGmode,aftertheaddresspointerreachestheendofthebuffer,itsets
6.42
9
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Flow Control Register Description(1,2)
0
15
MSB
H
H
H
H
H
H
H
H
H
H
4
3
2
1
0
LSB I/O BITS
H
Counter Release
(STOP Mode Only)
Buffer #1 flow control
Buffer #2 flow control
3099 drw 11
NOTES:
1. "H" = VOH for I/O in the output state and "Don't Cares"' for I/O in the input state.
2. Writing a 0 into bit 4 releases the address pointer after it is stopped due to the STOP mode and allows sequential write operations to resume. This occurs asynchronously
of SCLK, and therefore caution should be taken. The pointer will be at address EOB+2 on the next rising edge of SCLK that is enabled by CNTEN. The pointer is
also released by RST, SLD, SSTRT1 and SSTRT2 operations.
Flow Control Bits(5)
Flow Control
Bit 1 & Bit 0
Mode
Functional Description
(Bit 3 & Bit 2)
00
01
BUFFER
EOB
1
(EOB2) is asserted (Active LOW output) when the pointer matches the end address of Buffer #1 (Buffer #2).
(1,3)
CHAINING
The pointer value is changed to the start address of Buffer #2 (Buffer #1)
STOP
EOB
1
(EOB2) is asserted when the pointer matches the end address of Butler #1 (Butler #2).
The address pointer will stop incrementing when it reaches the next address (EOB address + 1), if CNTEN is LOW
on the next clock's rising edge. Otherwise, the address pointer will stop incrementing on EOB. Sequential write
operations are inhibited after the address pointer is stopped. The pointer can be released by bit 4 of the flow
control register.(1,2,4)
3099 tbl 17
NOTES:
1. EOB1 and EOB2 may be asserted (set) at the same time, if both end addresses have been loaded with the same value.
2. CMD flow control bits are unchanged, the count does not continue advancement.
3. If EOB1 and EOB2 are equal, then the pointer will jump to the start of Buffer #1.
4. If the counter has stopped at EOBx and was released by bit 4 of the flow control register, CNTEN must be LOW on the next rising edge of SCLK; otherwise the flow
control will remain in the stop mode.
5. Flow Control Bit settings of '10' and '11' are reserved.
6. Start address and End of address for Buffer #2 and the Flow Control for both Buffer #1 and #2, must be programmed as described in the "Buffer Command Mode"
section. RST conditions are not set to valid addresses.
Cases 6 and 7: Flag Status Register Bit Description(1)
0
0
15
H
MSB
H
H
H
H
H
H
H
H
H
H
H
H
H
1
LSB I/O BITS
End of buffer flag for Buffer #1
End of buffer flag for Buffer #2
NOTE:
1. "H" = VOH for I/O in the output state and "Don't Cares" for I/O in the input state.
3099 drw 12
Cases 6: Flag Status Register
Write Conditions(1)
Case 7: Flag Status Register Read
Conditions
Flag Status Bit 0, (Bit 1)
Functional Description
, (EOB ).
No chang e to the Buffer Flag. (2)
Flag Status Bit 0, (Bit 1)
Functional Description
0
1
Clears Buffer Flag EOB
1
2
0
EOB
1
(EOB2) flag has not been set, the
Pointer has not reached the End of the
Buffer.
3099 tbl 18
NOTES:
1. Either bit 0 or bit 1, or both bits, may be changed simultaneously. One may be
cleared while the second is left alone, or both may be cleared.
2. Remains as it was prior to the CMD operation, either HIGH (1) or LOW (0).
1
EOB
1
(EOB2) flag has been set, the
Pointer has reached the end of the
Buffer.
3099 tbl 19
Cases 8 and 9: (Reserved)
Illegal operations. All outputs will be HIGH on the I/O bus during a READ.
10
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Random Access Port: AC Electrical Characteristics Over
theOperatingTemperatureandSupplyVoltageRange(2,4,5)
70824X20
70824X25
70824X35
Com'l &
Military
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
____
____
t
RC
AA
ACE
BE
OE
OH
CLZ
BLZ
OLZ
CHZ
BHZ
OHZ
PU
PD
Read Cycle Time
20
25
35
45
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
____
____
____
____
t
Address Access Time
20
20
20
25
25
25
35
35
35
45
45
45
____
____
____
____
____
____
____
____
____
____
____
____
t
Chip Enable Access Time
Byte Enable Access Time
Output Enable Access Time
Output Hold from Address Change
Chip Select Low-Z Time(1)
Byte Select Low-Z Time(1)
Output Enable Low-Z Time(1)
Chip Select High-Z Time(1)
Byte Select High-Z Time(1)
Output Select High-Z Time(1)
Chip Select Power-Up Time
Chip Select Power-Down Time
t
t
10
10
15
20
____
____
____
____
t
3
3
3
3
3
3
3
3
3
3
3
3
____
____
____
____
____
____
____
____
____
____
____
____
t
t
t
2
2
2
2
____
.____
____
____
t
10
10
12
12
15
15
15
15
____
____
____
____
____
____
____
____
t
t
9
11
15
15
____
____
____
____
t
0
0
0
0
____
____
____
____
t
20
25
35
45
ns
3099 tbl 20
Random Access Port: AC Electrical Characteristics
Over the Operating Temperature and Supply Voltage(2,4,5)
70824X20
70824X25
70824X35
Com'l &
Military
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
WC
CW
AW
AS
WP
BP
WR
WHZ
DW
DH
OW
Write Cycle Time
20
15
15
0
25
20
20
0
35
25
25
0
45
30
30
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Chip Enable to End-of-Write
Address Valid to End-of-Write(3)
Address Set-up Time
t
t
(3)
t
Write Pulse Width
13
15
20
20
25
25
30
30
t
Byte Enable Pulse Width(3)
Write Recovery Time
t
0
0
0
0
Write Enable Output High-Z Time(1)
Data Set-up Time
10
12
15
15
____
____
____
____
t
____
____
____
____
t
13
0
15
0
20
0
25
0
____
____
____
____
____
____
____
____
t
Data Hold Time
t
Output Active from End-of-Write
3
3
3
3
ns
3099 tbl 21
NOTES:
1. Transition measured at 0mV from steady state. This parameter is guaranteed with the AC Output Test Load (Figure 1) by device characterization, but is not
production tested.
2. 'X' in part number indicates power rating (S or L).
3. OE is continuously HIGH, OE = VIH. If during the R/W controlled write cycle the OE is LOW, tWP must be greater or equal to tWHZ + tDW to allow the I/O drivers to
turn off and on the data to be placed on the bus for the required tDW. If OE is HIGH during the R/W controlled write cycle, this requirement does not apply and the minimum
write pulse is the specified tWP. For the CE controlled write cycle, OE may be LOW with no degradation to tCW timing.
4. CMD access follows standard timing listed for both read and write accesses, (CE = VIH when CMD = VIL) or (CMD = VIH when CE = VIL).
5. Industrial temperature: for specific speeds, packages and powers contact your sales office.
6.42
11
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Waveform of Read Cycles: Random Access Port(1,2)
tRC
ADDR
tAA
t
OH
(2)
ACS
t
CE
t
CHZ
t
CLZ
LB, UB
t
BHZ
tBE
t
BLZ
OE
t
OE
t
OHZ
t
OLZ
I/OOUT
Valid Data Out
3099 drw 13
NOTES:
1. R/W is HIGH for read cycle.
2. Address valid prior to or coincident with CE transition LOW; otherwise tAA is the limiting parameter.
Waveform of Read Cycles: Buffer Command Mode
tRC
ADDR
tAA
tOH
(1)
CMD
tACS
t
CHZ
tCLZ
LB, UB
t
t
BHZ
OHZ
t
BE
tBLZ
OE
t
OE
t
OLZ
I/OOUT
Valid Data Out
3099 drw 14
NOTE:
1. CE = VIH when CMD = VIL.
12
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Waveform of Write Cycle No.1 (R/W Controlled Timing)
RandomAccessPort(1,6)
tWC
ADDR
tAW
R/W
(3)
(2)
WP
tWR
t
tAS
(8)
(5)
CE, LB, UB
tDH
tDW
I/OIN
Valid Data In
OE
tOHZ
tWHZ
(4)
Data Out
Data Out(4)
I/OOUT
t
ACS
tOW
tBE
3099 drw 15
Waveform of Write Cycle No.2 (CE, LB, and/or UB Controlled Timing)
RandomAccessPort(1,6,7)
t
WC
ADDR
tAW
(8)
(5)
CE, LB, UB
(3)
t
AS
(2)
tWR
t
t
CW
(2)
BP
R/W
t
DW
tDH
I/OIN
Valid Data
3099 drw 16
NOTES:
1. R/W, CE, or LB and UB must be inactive during all address transitions.
2. A write occurs during the overlap of R/W = VIL, CE = VIL and LB = VIL and/or UB = VIL.
3. tWR is measured from the earlier of CE (and LB and/or UB) or R/W going HIGH to the end of the write cycle.
4. During this period, I/O pins are in the output state and the input signals must not be applied.
5. If the CE LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the High-impedance state.
6. OE is continuously HIGH, OE = VIH. If during the R/W controlled write cycle the OE is LOW, tWP must be greater or equal to tWHZ + tDW to allow the I/O drivers to
turn off and on the data to be placed on the bus for the required tDW. If OE is HIGH during the R/W controlled write cycle, this requirement does not apply and the minimum
write pulse is the specified tWP. For the CE controlled write cycle, OE may be LOW with no degregation to tCW timing.
7. I/OOUT is never enabled, therefore the output is in High-Z state during the entire write cycle.
8. CMD access follows the standard CE access described above. If CMD = VIL, then CE must = VIH or, when CE = VIL, CMD must = VIH.
6.42
13
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Sequential Port: AC Electrical Characteristics Over
theOperatingTemperatureandSupplyVoltageRange(1,3)
70824X20
70824X25
70824X35
Com'l &
Military
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
CYC
CH
CL
ES
EH
SOE
OLZ
OHZ
CD
CKHZ
CKLZ
EB
Sequential Clock Cycle Time
25
10
10
5
30
12
12
5
40
15
15
6
50
18
18
6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Clock Pulse HIGH
t
Clock Pulse LOW
t
Count Enable and Address Pointer Set-up Time
Count Enable and Address Pointer Hold Time
Output Enable to Data Valid
Output Enable Low-Z Time(2)
Output Enable High-Z Time(2 )
Clock to Valid Data
t
2
2
2
2
____
____
____
____
t
8
10
15
20
____
____
____
____
t
2
2
2
2
____
____
____
____
t
9
11
25
15
35
15
45
____
____
____
____
t
20
Clock High-Z Time(2)
12
14
17
20
____
____
____
____
t
t
Clock Low-Z Time(2)
3
3
3
3
____
____
____
____
____
____
____
____
t
Clock to EOB
13
15
18
23
ns
3099 tbl 22
Sequential Port: AC Electrical Characteristics
Over the Operating Temperature and Supply Voltage(1,3)
70824X20
70824X25
70824X35
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Com'l &
Military
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
CYC
FS
WS
WH
DS
DH
Sequential Clock Cycle Time
25
13
5
30
15
5
40
20
6
50
20
6
ns
ns
ns
ns
ns
t
Flow Restart Time
t
Chip Select and Read/Write Set-up Time
Chip Select and Read/Write Hold Time
Input Data Set-up Time
t
2
2
2
2
t
5
5
6
6
t
Input Data Hold Time
2
2
2
2
ns
3099 tbl 23
NOTES:
1. 'X' in part number indicates power rating (S or L).
2. Transition measured at 0mV from steady state. This parameter is guaranteed with the AC Output Test Load (Figure 1) by device characterization, but is not
production tested.
3. Industrial temperature: for specific speeds, packages and powers contact your sales office.
14
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Sequential Port: AC Electrical Characteristics
Over the Operating Temperature and Supply Voltage(1,2)
70824X20
70824X25
70824X35
Com'l &
Military
70824X45
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
RSPW
WERS
RSRC
RSFV
Reset Pulse Width
13
10
10
15
15
10
10
20
20
10
10
25
20
10
10
25
ns
ns
ns
t
Write Enable HIGH to Reset HIGH
Reset HIGH to Write Enable LOW
Reset HIGH to Flag Valid
t
t
ns
3099 tbl 24
NOTES:
1. 'X' in part numbers indicates power rating (S or L).
2. Industrial temperature: for specific speeds, packages and powers contact your sales office.
Sequential Port: Write, Pointer Load Non-Incrementing Read
tCYC
tCH
tCL
SCLK
tEH
tES
(2)
(3)
CNTEN
tEH
tES
(1)
SLD
tDS
tDH
HIGH IMPEDANCE
Dx
A0
SI/OIN
t
WS
WS
t
WS
t
WH
t
WH
SR/W
SCE
SOE
t
tWS
tWH
t
WH
t
tCCKSHZZ
t
CD
SOE
OLZ
t
t
tOHZ
D0
D0
D0
SI/OOUT
3099 drw 17
tCKLZ
NOTES:
1. If SLD = VIL, then address will be clocked in on the SCLK's rising edge.
2. If CNTEN = VIH for the SCLK's rising edge, the internal address counter will not advance.
3. Pointer is not incremented on cycle immediately following SLD even if CNTEN is LOW.
6.42
15
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Sequential Port: Write, Pointer Load, Burst Read
tCYC
tCH
tCL
SCLK
CNTEN
SLD
tEH
tES
(3)
(2)
tEH
tES
(1)
t
DS
t
DS
tDH
tDH
HIGH IMPEDANCE
D2
SI/OIN
Dx
A0
tWS
tWS
tWH
tWH
SR/W
SCE
t
WS tWH
tWS
tWH
tSD
tSOP
SOE
tOHZ
tOLZ
(2)
SI/OOUT
D0
D1
3099 drw 18
tCKLZ
NOTES:
1. If SLD = VIL, then address will be clocked in on the SCLK's rising edge.
2. If CNTEN = VIH for the SCLK's rising edge, the internal address counter will not advance.
3. Pointer is not incremented on cycle immediately following SLD even if CNTEN is LOW.
Read STRT/EOB Flag Timing - Sequential Port
tCYC
tCH
tCL
SCLK
tEH
tES
(4)
CNTEN
(2)
tES
tEH
(1)
SSTRT1/2
tDS
tDH
HIGH IMPEDANCE
SI/OIN
D3
Dx
t
WS tWH
tWS
tWH
SR/W
SCE
SOE
t
WS
tWS
tWH
tWH
(3)
tCD
t
SOE
(5)
tOHZ
t
OLZ
(2)
SI/OOUT
D0
D1
D2
tCKLZ
EOB1/2
tEB
3099 drw19
NOTES: (Also used in Figure "Read STRT/EOB Flag Timing")
1. If SSTRT1 or SSTRT2 = VIL, then address will be clocked in on the SCLK's rising edge.
2. If CNTEN = VIH for the SCLK's rising edge, the internal address counter will not advance.
3. SOE will control the output and should be HIGH on power-up. If SCE = VIL and is clocked in while SR/W = VIH, the data addressed will be read out within that
cycle. If SCE = VIL and is clocked in while SR/W = VIL, the data addressed will be written to if the last cycle was a read. SOE may be used to control the bus
contention and permit a write on this cycle.
4. Unlike SLD case, CNTEN is not disabled on cycle immediately following SSTRT.
5. If SR/W = VIL, data would be written to D0 again since CNTEN = VIH.
6. SOE = VIL makes no difference at this point since the SR/W = VIL disables the output until SR/W = VIH is clocked in on the next rising clock edge.
16
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Waveform of Write Cycles: Sequential Port
tCYC
tCH
tCL
SCLK
t
EH
tEH
(4)
t
ES
tES
(3)
CNTEN
SLD
tES
t
EH
(1)
t
DS
t
DS
t
DS
tDH
tDH
t
DH
HIGH IMPEDANCE
Dx
A0
D1
SI/OIN
D0
t
WS
t
WS
t
WH
tWH
(4)
SR/W
SCE
tWS
tWS
t
WH
tWH
tCKHZ
tCD
(5)
SOE
t
OHZ
HIGH IMPEDANCE
SI/OOUT
D0
3099 drw 20
tCKLZ
Waveform of Burst Write Cycles: Sequential Port
t
CYC
t
CH
tCL
SCLK
t
EH
t
ES
(3)
CNTEN
SLD
(2)
t
EH
t
ES
(1)
tDS
tDS
tDH
tDH
SI/OIN
Dx
A0
D0
D1
D2
t
WS
t
WS
t
WH
tWH
SR/W
(5)
tWS
tWS
t
WH
t
WH
SCE
SOE
(5)
tCKLZ
t
CD
HIGH IMPEDANCE
SI/OOUT
D2
3099 drw 21
NOTES:
1. If SLD = VIL, then address will be clocked in on the SCLK's rising edge.
2. If CNTEN = VIH for the SCLK's rising edge, the internal address counter will not advance.
3. Pointer is not incrementing on cycle immediately following SLD even if CNTEN is LOW.
4. If SR/W = VIL, data would be written to D0 again since CNTEN = VIH.
5. SOE = VIL makes no difference at this point since the SR/W = VIL disables the output until SR/W = VIH is clocked in on the next rising clock edge.
6.42
17
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Waveform of Write Cycles: Sequential Port (STRT/EOB Flag Timing)
tCH
t
CL
SCLK
CNTEN
t
EH
tES
(2)
(4)
tEH
tES
(1)
SSTRT1/2
t
DS
t
DH
HIGH IMPEDANCE
SI/OIN
D0
D1
Dx
D2
D3
tWS
tWS
t
WH
tWH
(5)
SR/W
SCE
SOE
t
WS
t
WS
tWH
tWH
(3)
(6)
tCKLZ
tCD
HIGH IMPEDANCE
SI/OOUT
D3
EOB1/2
tEB
3099 drw 22
NOTES: (Also used in Figure "Read STRT/EOB Flag Timing")
1. If SSTRT1 or SSTRT2 = VIL, then address will be clocked in on the SCLK's rising edge.
2. If CNTEN = VIH for the SCLK's rising edge, the internal address counter will not advance.
3. SOE will control the output and should be HIGH on power-up. If SCE = VIL and is clocked in while SR/W = VIH, the data addressed will be read out within that
cycle. If SCE = VIL and is clocked in while SR/W = VIL, the data addressed will be written to if the last cycle was a read. SOE may be used to control the bus
contention and permit a write on this cycle.
4. Unlike SLD case, CNTEN is not disabled on cycle immediately following SSTRT.
5. If SR/W = VIL, data would be written to D0 again since CNTEN = VIH.
6. SOE = VIL makes no difference at this point since the SR/W = VIL disables the output until SR/W = VIH is clocked in on the next rising clock edge.
18
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Sequential Counter Enable Cycle After Reset, Write Cycle(1,4,6)
SCLK
RST
(2)
CNTEN
D0
D1
D2
D3
D4
SI/OIN
3099 drw 23
Sequential Counter Enable Cycle After Reset, Read Cycle(1,4)
SCLK
RST
(3)
SR/W
(5)
CNTEN
D0(5)
D3
D1
D2
SI/OOUT
3099 drw 24
NOTES:
1. 'D0' represents data input for Address = 0, 'D1' represents data input for Address = 1, etc.
2. If CNTEN = VIL then 'D1' would be written into 'A1' at this point.
3. Data output is available at a tCD after the SR/W = VIH is clocked. The RST sets SR/W = LOW internally and therefore disables the output until the next clock.
4. SCE = VIL throughout all cycles.
5. If CNTEN=VIL then 'D1' would be clocked out (read) at this point.
6. SR/W = VIL.
6.42
19
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
Random Access Port - Reset Timing
tRSPW
RST
tRSRC
R/W, SR/W CMD
or (UB + LB)(4)
tWERS
tRSFV
EOB(1 or 2)
Flag Valid
3099 drw 25
Random Access Port Restart Timing of Sequential Port(1)
0.5 x tCYC
tFS
SCLK
R/W
(2)
2-5ns
6-7ns
CLR(3)
Block
3099 drw 26
(Internal Signal)
NOTES:
1. The sequential port is in the STOP mode and is being restarted from the random port by the Bit 4 Counter Release (see Case 5).
2. "0" is written to Bit 4 from the random port at address [A2 - A0] = 100, when CMD = VIL and CE = VIH. The device is in the Buffer Command Mode (see Case 5).
3. CLR is an internal signal only and is shown for reference only.
4. Sequential port must also prohibit SR/W or SCE from being LOW for tWERS and tRSRC periods or SCLK must not toggle from LOW-to-HIGH until after tRSRC.
20
IDT70824S/L
High-Speed 4K x 16 Sequential Access Random Access Memory
Military and Commercial Temperature Ranges
OrderingInformation
70824
X
XX
X
X
Device
Type
Power Speed
Package
Process/
Temperature
Range
Blank
I(1)
B
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
Military (–55°C to +125°C)
Compliant to MIL-PRF-38535 QML
84-pin PGA (G84-3)
80-pin TQFP (PN80-1)
G
PF
Commercial Only
Commercial Only
Commercial & Military
Commercial & Military
20
25
35
45
Speed in nanoseconds
Standard Power
Low Power
S
L
70824 64K (4K x 16) Sequential Access Random
Access Memory
,
3099 drw 27
NOTE:
1. Industrial temperature range is available on selected TQFP packages in standard power.
For specific speeds, packages and powers contact your sales office.
DatasheetDocumentHistory
3/8/99:
Initiateddatasheetdocumenthistory
Convertedtonewformat
Cosmeticandtypographicalcorrections
Page 2 Addedadditionalnotestopinconfigurations
Changeddrawingformat
6/4/99:
11/10/99:
4/18/00:
Replaced IDT logo
Page 3 Added"Outputs"inSequentialpindescriptiontable
Changed±200mVto0mVinnotes
5/23/00:
Page 4 Increasedstoragetemperatureparameter
ClarifiedTAparameter
Page 5 DCElectricalparameters–changedwordingfrom"open"to"disabled"
Page 21 Removed "IDT" from orderable part number
01/29/09:
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
for Tech Support:
408-284-2794
DualPortHelp@idt.com
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
6.42
21
相关型号:
©2020 ICPDF网 联系我们和版权申明