70V639S12BCG [IDT]
HIGH-SPEED 3.3V 128K x 18 ASYNCHRONOUS DUAL-PORT STATIC RAM;型号: | 70V639S12BCG |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | HIGH-SPEED 3.3V 128K x 18 ASYNCHRONOUS DUAL-PORT STATIC RAM |
文件: | 总24页 (文件大小:705K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HIGH-SPEED 3.3V
128K x 18 ASYNCHRONOUS
DUAL-PORT STATIC RAM
IDT70V639S
Features
◆
True Dual-Port memory cells which allow simultaneous
access of the same memory location
High-speed access
◆
◆
Fully asynchronous operation from either port
◆
Separate byte controls for multiplexed bus and bus
matching compatibility
– Commercial:10/12/15ns(max.)
◆
Supports JTAG features compliant to IEEE 1149.1
– Due to limited pin count, JTAG is not supported on the
128-pin TQFP package.
– Industrial:12/15ns(max.)
◆
◆
Dual chip enables allow for depth expansion without
external logic
◆
◆
◆
◆
◆
LVTTL-compatible, single 3.3V (±150mV) power supply for
core
IDT70V639 easily expands data bus width to 36 bits or
more using the Master/Slave select when cascading more
than one device
LVTTL-compatible, selectable 3.3V (±150mV)/2.5V (±100mV)
power supply for I/Os and control signals on each port
Available in a 128-pin Thin Quad Flatpack, 208-ball fine
pitch Ball Grid Array, and 256-ball Ball Grid Array
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
◆
M/S = VIH for BUSY output flag on Master,
M/S = VIL for BUSY input on Slave
Busy and Interrupt Flags
◆
◆
◆
On-chip port arbitration logic
Full on-chip hardware support of semaphore signaling
Green parts available, see ordering information
between ports
Functional Block Diagram
UB
LB
L
UB
R
L
LB
R
R/WL
R/WR
B
B
E
1
L
B
E
1
B
E
0
E
0
L
CE0L
CE0R
R
R
CE1L
CE1R
OEL
OER
Dout0-8_L
Dout0-8_R
Dout9-17_L
Dout9-17_R
128K x 18
MEMORY
ARRAY
Din_L
I/O0L- I/O17L
Din_R
I/O0R - I/O17R
A
A
16R
0R
Address
Decoder
Address
Decoder
A
16L
0L
ADDR_L
ADDR_R
A
OE
L
ARBITRATION
OER
INTERRUPT
SEMAPHORE
LOGIC
CE0R
CE1R
CE0L
CE1L
R/WL
R/WR
BUSY
SEM
INT
R
BUSY
SEM
INT
L
L
M/S
R
L
R
TMS
TCK
TRST
TDI
JTAG
TDO
5621 drw 01
NOTES:
1. BUSY is an input as a Slave (M/S=VIL) and an output when it is a Master (M/S=VIH).
2. BUSY and INT are non-tri-state totem-pole outputs (push-pull).
JUNE 2015
1
DSC-5621/7
©2015 Integrated Device Technology, Inc.
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Description
TheIDT70V639isahigh-speed128Kx18AsynchronousDual-Port address,andI/Opinsthatpermitindependent,asynchronousaccessfor
Static RAM. The IDT70V639 is designed to be used as a stand-alone reads or writes to any location in memory. An automatic power down
2304K-bit Dual-Port RAM or as a combination MASTER/SLAVE Dual- feature controlled by the chip enables (either CE0 or CE1) permit the
Port RAM for 36-bit-or-more word system. Using the IDT MASTER/ on-chip circuitry of each port to enter a very low standby power mode.
SLAVE Dual-Port RAM approach in 36-bit or wider memory system
The70V639cansupportanoperatingvoltageofeither3.3Vor2.5V
applicationsresultsinfull-speed,error-freeoperationwithouttheneedfor on one or both ports, controlled by the OPT pins. The power supply for
additionaldiscretelogic.
thecoreofthedevice(VDD)remainsat3.3V.
This device provides two independent ports with separate control,
PinConfigurations(1,2,3,4)
1
2
3
4
5
6
7
8
9
11 12 13 14
10
16 17
15
V
V
V
DD
I/O9L
A
12L
A
B
C
D
E
F
NC
V
SS
A
16L
13L
A
8L
NC
A
0L
VSS
A
4L
OPT
L
NC
I/O8L
NC
TDO
NC
SEM
L
INTL
A
B
C
D
E
F
NC
VSS
A
9L
NC
SS
SS
A5L
TDI
NC
NC
A
A
1L
V
DDQR
NC
NC
CE0L
V
V
SS
DD
BUSY
L
A
A
10L
V
SS
I/O7R
NC
I/O9R
V
DD
A
14L
CE1L
A2L
I/O8R
A6
L
V
DDQL
V
DDQR
UB
L
R/W
L
NC
VSS
I/O10L
A
15L
A
11L
7L
V
DD
VDDQL
I/O7L
NC
NC
VDD
NC
LB
L
A
3L
OE
L
VDDQR I/O10R
I/O11L
NC
I/O6L
NC
VSS
V
DDQL
VSS
I/O11R
I/O6R
V
DDQR
V
SS
NC
NC
NC
V
SS
I/O12L
NC
V
DDQL
I/O5L
NC
NC
G
H
J
G
H
J
70V639BF
BF208(5)
V
DD
NC
V
DDQR
V
DD
SS
I/O12R
NC
V
SS
I/O5R
VDDQL
VDD
VSS
V
V
DDQR
V
DD
V
SS
VSS
208-Ball BGA
Top View(6)
V
DDQL
I/O3R
NC
V
SS
I/O4R
I/O14R
NC
VSS
I/O13R
K
L
VSS
K
L
I/O14L
VDDQR
I/O13L
I/O3L
NC
V
SS
I/O4L
V
DDQL
I/O15R
NC
VSS
NC
VSS
I/O2R
NC
VDDQR
M
N
P
R
T
M
N
P
R
T
NC
V
SS
I/O15L
NC
I/O1R
NC
V
DDQL
I/O2L
NC
I/O1L
I/O16R
I/O16L
VDDQR
V
DD
INT
R
A4R
V
SS
TRST
A
16R
A
12R
A8R
NC
SEM
R
V
SS
V
DDQL
I/O0R
VDDQR
V
V
SS
SS
A
5R
A
1R
2R
A13R
A
9R
NC
NC
NC
TCK
TMS
NC
CE0R
VSS
NC
I/O17R
BUSY
R
V
SS
V
SS
A
NC
NC
A6R
A14R
A10R
CE1R
NC
I/O17L
V
DDQL
UB
R
R/WR
V
DD
OPT
R
NC
I/O0L
VDD
A
3R
A
0R
A
11R
A7R
VSS
VDD
M/S
NC
A15R
LBR
OER
U
U
5621 tbl 02b
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is
set to VIL (0V).
3. All VSS pins must be connected to ground.
4. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
2
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Pin Configurations(1,2,3,4,7) (con't.)
A
A
OPT
1L
0L
1
2
3
4
5
6
7
8
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
A
A
14L
15L
L
A16L
NC
IO9L
IO9R
DDQL
VSS
IO8L
IO8R
NC
V
VSS
V
IO10L
IO10R
DDQR
SS
VDDQL
9
10
IO7L
IO7R
V
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
VSS
V
SS
VDDQR
IO11L
IO11R
IO12L
IO12R
V
V
V
V
IO13R
IO13L
IO14R
IO14L
IO15R
IO15L
DDQL
V
IO16R
IO16L
IO6L
IO6R
IO5L
IO5R
70V639PRF
PK128(5)
DD
VDD
VDD
VSS
VSS
DD
SS
128-Pin TQFP
Top View(6)
SS
IO4R
IO4L
IO3R
IO3L
IO2R
IO2L
V
VSS
SS
VDDQL
IO1R
IO1L
V
DDQR
VSS
V
SS
VDDQR
IO17R
IO17L
NC
IO0R
IO0L
OPT
R
A16R
A15R
A14R
A
A
0R
1R
5621 drw 02a
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is
set to VIL (0V).
3. All VSS pins must be connected to ground.
4. Package body is approximately 14mm x 20mm x 1.4mm.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
7. Due to the restricted number of pins, JTAG is not supported in the PK128 package.
3
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Pin Configuration(1,2,3,4) (con't.)
70V639BC
BC256(5)
256-Pin BGA
Top View(6)
A1
A2
A3
A6
A7
A8
A9
A11
A12
A13
A14
A4
A5
A10
A15
A16
NC
TDI
NC
A
11L
A
8L
9L
7L
NC CE1L
INT
L
A
5L
A
2L
A
0L
NC
A
14L
OE
L
NC
NC
B1
B2
B3
B6
B7
B9
B11
B12
B13
B4
B5
B8
B10
B14
B15
B16
NC
NC TDO
A
12L
A
CE0L
NC
A4L
A
1L
NC
A
15L
UBL
R/W
L
NC
NC
NC
C1
C5
C6
C2
C3
C4
C7
C8
C9
C10
C11
C12
C13
C16
C14
C15
NC
A
13L
A
10L
I/O9L
V
SS
A16L
A
NC
LB
L
SEM
L
BUSY
L
A6L
A
3L
I/O8L
OPT
L
NC
D1
D2
D6
D9
DDQL
D11
D3
D5
D7
D8
DDQR
D10
D12
D13
D14
D15
D16
D4
NC I/O9R
VDDQL
V
VDDQR
V
NC
VDDQL
V
DDQR
V
VDDQL
DDQR
VDD
NC
NC I/O8R
V
DD
E5
E6
E7
E8
E9
E10
E11
E12
E13
E1
E2
E3
E4
DDQL
E14
E16
E15
V
DD
V
DD
SS
SS
SS
V
SS
V
SS
V
SS
SS
SS
VSS
VDD
VDD
V
DDQR
I/O10R I/O10L NC
V
NC
I/O7R
I/O7L
F7
F5
F6
F9
F10
F1
F2
F3
F11
F13
F14
F15
F16
F8
F12
F4
V
SS
I/O11L NC I/O11R
V
DD
V
V
V
SS
I/O6R NC I/O6L
DDQR
VSS
V
VDDQL
V
SS
SS
SS
VDD
G1
G2
G3
G5
H5
G4
G6
G8
G9
G14
G15
G16
G7
G10
G12
G13
G11
NC
V
SS
NC
VDDQR
V
V
V
I/O12L
I/O5L NC
VDDQL
NC
V
SS
VSS
VSS
VSS
H11
H12
H16
H13
H7
H8
H9
H10
H14
H15
H6
H3
H4
H1
H2
VSS
VSS
I/O5R
VDDQL
V
SS
V
V
SS
V
SS
NC
NC
NC
VDDQR
V
SS
SS
SS
V
NC I/O12R
J1
J2
J3
J4
J5
J6
J7
J8
J9
J13
J10
J11
J12
J14
J15
J16
I/O13L
V
I/O14R I/O13R
V
DDQL
V
SS
V
SS
V
SS
V
SS
V
DDQR
I/O4R
VSS
VSS
VSS
I/O3R I/O4L
K6
K8
K10
K12
K13
K2
K4
K5
K7
K9
K11
K15
K16
K1
K3
K14
V
SS
V
SS
V
SS
SS
VSS
V
DDQR
NC
V
DDQL
V
V
SS
SS
SS
V
SS
VSS
NC I/O3L
NC
I/O14L
NC
L7
L8
L11
L12
L13
L5
L6
L9
L10
L3
L4
L15
L16
L1
L2
L14
V
V
SS
VSS
VDD
V
DDQL
I/O15R
VDDQR
V
DD
V
SS
V
SS
V
NC I/O2R
I/O15L NC
I/O2L
M5
M6
M7
M8
M9
M10
M11
M12
M13
M1
M2
M3
M4
M16
M14
M15
V
DD
V
DD
V
V
SS
V
SS
VSS
VDD
VDD
V
DDQL
I/O16R I/O16L NC
VDDQR
NC
I/O1R I/O1L
N8
N12
N13
N16
N5
N6
DDQR
N7
DDQL
N9
N10
N11
N4
N15
N1
N2
N3
N14
VDDQL
VDDQL
NC
VDD
V
DD
V
DDQR
V
V
V
DDQR
V
DDQR
VDDQL
I/O0R
NC I/O17R NC
NC
P1
P2
P3
P4
P5
P7
P8
P9
P10
P11
P12
P14
P15
P16
P6
P13
NC I/O17L TMS
A16R
A13R
A7R
NC
LBR
SEM
R
BUSY
R
A6R
NC
NC I/O0L
A10R
A3R
R5
R6
R7
R8
R9
R10
R11
R16
R1
R2
R3
R4
R12
R13
R14
R15
A15R
A
12R
A9R
UBR
CE0R R/W
R
M/S
NC
NC
NC TRST NC
A4R
A1R OPTR
NC
T2
T3
T1
T4
T5
T8
T9
T15
T16
T6
T7
T10
T11
T12
T13
2R
T14
TCK
NC
NC
NC
A
14R
NC CE1R
NC
NC
A
11R
A
8R
OE
R
INT
R
A
5R
A
A
0R
5621 drw 02c
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V), and 2.5V if OPT pin for that port is
set to VIL (0V).
3. All VSS pins must be connected to ground supply.
4. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
4
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
PinNames
Left Port
Right Port
Names
Chip Enables
CE0L
,
CE1L
CE0R, CE1R
R/W
L
R/W
R
Read/Write Enable
Output Enable
OEL
OER
A
0L - A16L
I/O0L - I/O17L
SEM
INT
BUSY
UB
LB
A
0R - A16R
I/O0R - I/O17R
SEM
INT
BUSY
UB
LB
Address
Data Input/Output
Semaphore Enable
Interrupt Flag
L
R
L
R
Busy Flag
L
R
Upper Byte Select
Lower Byte Select
Power (I/O Bus) (3.3V or 2.5V)(1)
L
R
L
R
V
DDQL
V
DDQR
(1,2)
OPT
L
OPTR
Option for selecting VDDQX
M/S
Master or Slave Select
Power (3.3V)(1)
V
V
DD
SS
Ground (0V)
NOTES:
1. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to
applying inputs on I/OX.
TDI
TDO
TCK
Test Data Input
2. OPTX selects the operating voltage levels for the I/Os and controls on that port.
If OPTX is set to VIH (3.3V), then that port's I/Os and controls will operate at 3.3V
levels and VDDQX must be supplied at 3.3V. If OPTX is set to VIL (0V), then that
port's I/Os and controls will operate at 2.5V levels and VDDQX must be supplied
at 2.5V. The OPT pins are independent of one another—both ports can operate
at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V
with the other at 2.5V.
Test Data Output
Test Logic Clock (10MHz)
Test Mode Select
Reset (Initialize TAP Controller)
TMS
TRST
5621 tbl 01
5
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table I—Read/Write and Enable Control(1)
Byte 1
I/O9-17
Byte 0
I/O0-8
CE
X
1
R/W
X
MODE
Deselected–Power Down
Deselected–Power Down
Both Bytes Deselected
Write to Byte 0 Only
Write to Byte 1 Only
Write to Both Bytes
OE
X
X
X
X
X
X
L
SEM
H
CE
0
UB
X
X
H
H
L
LB
X
X
H
L
H
X
L
L
L
L
L
L
L
L
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
H
L
X
H
H
H
H
H
H
H
H
H
X
H
L
DIN
H
H
L
L
DIN
High-Z
H
L
L
DIN
DIN
H
H
L
L
H
H
H
X
High-Z
DOUT
Read Byte 0 Only
L
H
H
L
DOUT
High-Z
Read Byte 1 Only
L
H
L
DOUT
DOUT
Read Both Bytes
H
H
L
L
High-Z
High-Z
Outputs Disabled
5621 tbl 02
NOTE:
1. "H" = VIH, "L" = VIL, "X" = Don't Care.
Truth Table II – Semaphore Read/Write Control(1)
Inputs(1)
Outputs
(2)
R/W
H
I/O1-17
I/O
0
Mode
CE
OE
UB
L
LB
L
SEM
H
H
L
L
X
X
L
L
L
DATAOUT
DATAOUT
Read Data in Semaphore Flag(3)
X
L
X
______
DATAIN
______
Write I/O
0
into Semaphore Flag
↑
X
X
X
Not Allowed
5621 tbl 03
NOTES:
1. There are eight semaphore flags written to I/O0 and read from all the I/Os (I/O0-I/O17). These eight semaphore flags are addressed by A0-A2.
2. CE = L occurs when CE0 = VIL and CE1 = VIH.
3. Each byte is controlled by the respective UB or LB. To read data UB and/or LB = VIL.
6
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
RecommendedOperating
RecommendedDCOperating
TemperatureandSupplyVoltage(1)
Conditions with VDDQ at 2.5V
Symbol
Parameter
Core Supply Voltage
I/O Supply Voltage(3)
Ground
Min. Typ.
Max.
Unit
V
Ambient
Grade
Commercial
Temperature
0OC to +70OC
-40OC to +85OC
GND
0V
V
+
+
DD
V
DD
DDQ
SS
3.15 3.3
3.45
3.3V
3.3V
150mV
150mV
V
2.4
0
2.5
2.6
V
Industrial
0V
V
0
0
V
5621 tbl 04
V
V
DDQ + 100mV(2)
Input High Voltage(3)
1.7
V
____
V
IH
NOTE:
(Address & Control Inputs)
1. This is the parameter TA. This is the "instant on" case temperature.
V
IH
IL
Input High Voltage - I/O(3)
1.7
-0.5(1)
DDQ + 100mV(2)
0.7
V
____
____
V
Input Low Voltage
V
5621 tbl 06
NOTES:
1. VIL > -1.5V for pulse width less than 10 ns.
2. VTERM must not exceed VDDQ + 100mV.
AbsoluteMaximumRatings(1)
3. To select operation at 2.5V levels on the I/Os and controls of a given port, the
OPTpinforthatportmustbesettoVIL (0V), andVDDQX forthatportmustbesupplied
as indicated above.
Symbol
Rating
Commercial
& Industrial
Unit
(2)
V
TERM
Terminal Voltage
-0.5 to +4.6
V
with Respect to GND
(3)
T
BIAS
STG
JN
OUT
Temperature Under Bias
Storage Temperature
Junction Temperature
DC Output Current
-55 to +125
-65 to +150
+150
oC
oC
oC
RecommendedDCOperating
Conditions with VDDQ at 3.3V
T
T
Symbol
Parameter
Core Supply Voltage
I/O Supply Voltage(3)
Ground
Min. Typ.
3.15 3.3
3.15 3.3
Max.
Unit
V
I
50
mA
V
DD
DDQ
SS
3.45
5621 tbl 05
V
3.45
V
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VTERM must not exceed VDD + 150mV for more than 25% of the cycle time or
4ns maximum, and is limited to < 20mA for the period of VTERM > VDD + 150mV.
3. Ambient Temperature Under Bias. No AC Conditions. Chip Deselected.
V
0
0
0
V
____
Input High Voltage
2.0
V
V
DDQ + 150mV(2)
V
V
IH
(Address & Control Inputs)(3)
____
____
V
IH
IL
Input High Voltage - I/O(3)
2.0
-0.3(1)
DDQ + 150mV(2)
0.8
V
V
Input Low Voltage
V
5621 tbl 07
NOTES:
1. VIL > -1.5V for pulse width less than 10 ns.
2. VTERM must not exceed VDDQ + 150mV.
3. To select operation at 3.3V levels on the I/Os and controls of a given port, the
OPT pin for that port must be set to VIH (3.3V), and VDDQX for that port must be
supplied as indicated above.
Capacitance(1)
(TA = +25°C, F = 1.0MHZ) TQFP ONLY
Symbol
Parameter
Input Capacitance
Output Capacitance
Conditions
IN = 0V
OUT = 0V
Max. Unit
CIN
V
8
pF
(2)
COUT
V
10.5
pF
5621 tbl 08
NOTES:
1. These parameters are determined by device characterization, but are not
production tested.
2. COUT also references CI/O.
7
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V ± 150mV)
70V639S
Max.
Symbol
|ILI
|ILO
Parameter
Input Leakage Current(1)
Output Leakage Current
Test Conditions
DDQ = Max., VIN = 0V to VDDQ
CE = VIH or CE = VIL, VOUT = 0V to VDDQ
OL = +4mA, VDDQ = Min.
OH = -4mA, VDDQ = Min.
OL = +2mA, VDDQ = Min.
OH = -2mA, VDDQ = Min.
Min.
___
Unit
µA
µA
V
|
V
10
10
___
___
|
0
1
V
OL (3.3V) Output Low Voltage(2)
OH (3.3V) Output High Voltage(2)
OL (2.5V) Output Low Voltage(2)
OH (2.5V) Output High Voltage(2)
I
0.4
___
V
I
2.4
___
V
V
I
0.4
___
V
V
I
2.0
V
5621 tbl 09
NOTES:
1. At VDD < - 2.0V input leakages are undefined.
2. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(3) (VDD = 3.3V ± 150mV)
70V639S10
Com'l Only
70V639S12
Com'l
70V639S15
Com'l
& Ind
& Ind
Typ.(4)
340
Typ.(4)
315
365
90
Symbol
Parameter
Test Condition
Version
COM'L
Max.
500
Max. Typ.(4)
Max. Unit
IDD
Dynamic Operating
Current (Both
mA
mA
mA
mA
CE
L
and CE
R
= VIL
,
S
S
S
S
S
S
465
515
125
150
325
365
300
350
75
440
490
100
125
315
350
Outputs Disabled,
____
____
(1)
Ports Active)
IND
f = fMAX
ISB1
Standby Current
(Both Ports - TTL
Level Inputs)
COM'L
IND
115
165
CE
f = fMAX
L = CER = VIH
(1)
____
____
115
200
225
100
175
200
(5)
ISB2
Standby Current
(One Port - TTL
Level Inputs)
CE"A" = VIL and CE"B" = VIH
COM'L
IND
225
340
Active Port Outputs Disabled,
____
____
(1)
f=fMAX
ISB3
Full Standby Current Both Ports CE
L
and
COM'L
IND
S
S
3
15
3
6
15
15
3
6
15
15
(Both Ports - CMOS
Level Inputs)
CE
R > VDDQ - 0.2V,
V
IN > VDDQ - 0.2V or VIN < 0.2V,
____
____
f = 0(2)
ISB4
Full Standby Current
(One Port - CMOS
Level Inputs)
mA
CE"A" < 0.2V and
COM'L
IND
S
S
220
335
195
220
320
360
170
195
310
345
CE"B" > VDDQ - 0.2V(5)
V
IN > VDDQ - 0.2V or VIN < 0.2V,
Active Port, Outputs Disabled,
____
____
(1)
f = fMAX
5621 tbl 10
NOTES:
1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, using "AC TEST CONDITIONS" at input
levels of GND to 3V.
2. f = 0 means no address or control lines change. Applies only to input at CMOS level standby.
3. Port "A" may be either left or right port. Port "B" is the opposite from port "A".
4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. IDD DC(f=0) = 120mA (Typ).
5. CEX = VIL means CE0X = VIL and CE1X = VIH
CEX = VIH means CE0X = VIH or CE1X = VIL
CEX < 0.2V means CE0X < 0.2V and CE1X > VDDQ - 0.2V
CEX > VDDQ - 0.2V means CE0X > VDDQ - 0.2V or CE1X - 0.2V
"X" represents "L" for left port or "R" for right port.
8
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Test Conditions (VDDQ - 3.3V/2.5V)
2.5V
Input Pulse Levels
GND to 3.0V / GND to 2.5V
2ns Max.
Input Rise/Fall Times
Input Timing Reference Levels
Output Reference Levels
Output Load
833Ω
1.5V/1.25V
1.5V1.25V
Figures 1 and 2
5621 tbl 11
DATAOUT
5pF*
770Ω
,
Figure 2. Output Test Load
3.3V
590Ω
5pF*
50Ω
50Ω
,
DATAOUT
DATAOUT
1.5V/1.25
10pF
435Ω
(Tester)
5621 drw 03
Figure 1. AC Output Test load.
,
5621 drw 04
Figure 2. Output Test Load
(For tCKLZ, tCKHZ, tOLZ, and tOHZ).
*Including scope and jig.
10.5pF is the I/O capacitance of this
device, and 10pF is the AC Test Load
Capacitance.
7
6
5
4
3
∆tAA
(Typical, ns)
2
1
•
•
•
•
,
20.5
50
80 100
200
30
-1
Capacitance (pF)
5621 drw 05
Figure 3. Typical Output Derating (Lumped Capacitive Load).
9
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(5)
70V639S10
Com'l Only
70V639S12
Com'l
70V639S15
Com'l
& Ind
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
____
t
RC
AA
ACE
ABE
AOE
OH
LZ
HZ
PU
PD
SOP
SAA
Read Cycle Time
10
____
12
____
15
____
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Address Access Time
10
10
5
12
12
6
15
15
7
Chip Enable Access Time(3)
Byte Enable Access Time(3)
Output Enable Access Time
____
____
____
____
____
____
____
____
____
t
t
t
5
____
6
____
7
____
t
Output Hold from Address Change
Output Low-Z Time(1,2)
Output High-Z Time(1,2)
Chip Enable to Power Up Time(2)
Chip Disable to Power Down Time(2)
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
3
0
0
3
0
0
3
0
0
____
____
____
t
t
4
____
6
____
8
____
t
0
____
0
____
0
____
t
10
4
10
6
15
8
____
____
____
t
t
3
10
3
12
3
20
ns
5621 tbl 12
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltage(5)
70V639S10
Com'l Only
70V639S12
70V639S15
Com'l
& Ind
Com'l
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
WC
EW
AW
AS
WP
WR
DW
DH
WZ
OW
SWRD
SPS
Write Cycle Time
10
8
12
10
10
0
15
12
12
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
Write Pulse Width
t
8
t
0
t
8
10
0
12
0
t
Write Recovery Time
Data Valid to End-of-Write
Data Hold Time(4)
Write Enable to Output in High-Z(1,2)
Output Active from End-of-Write(1,2,4)
SEM Flag Write to Read Time
SEM Flag Contention Window
0
t
6
8
10
t
0
____
0
____
0
____
t
4
____
4
____
4
____
t
0
5
5
0
5
5
0
5
5
____
____
____
____
____
____
t
t
ns
5621 tbl 13
NOTES:
1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2).
2. Thisparameterisguaranteedbydevicecharacterization,butisnotproductiontested.
3. To access RAM, CE= VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage
and temperature, the actual tDH will always be smaller than the actual tOW.
5. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 5 for details.
10
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of Read Cycles(5)
tRC
ADDR
(4)
t
t
AA
(4)
ACE
CE(6)
(4)
tAOE
OE
(4)
t
ABE
UB, LB
R/W
tOH
(1)
tLZ
VALID DATA(4)
DATAOUT
(2)
tHZ
BUSYOUT
(3,4)
5621 drw 06
tBDD
NOTES:
1. Timing depends on which signal is asserted last, OE, CE, LB or UB.
2. Timing depends on which signal is de-asserted first CE, OE, LB or UB.
3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY
has no relation to valid output data.
4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD.
5. SEM = VIH.
Timing of Power-Up Power-Down
CE
t
PU
tPD
ICC
50%
50%
.
5621 drw 07
ISB
11
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8)
t
WC
ADDRESS
(7)
t
HZ
OE
t
AW
CE or SEM(9)
(7)
tHZ
(3)
(6)
(2)
t
WR
t
AS
tWP
UB, LB
R/W
(7)
t
LZ
t
OW
t
WZ
(4)
(4)
OUT
DATA
t
DH
t
DW
IN
DATA
,
5621 drw 08
Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5)
tWC
ADDRESS
tAW
CE or SEM(9)
UB, LB(9)
(6)
AS
(3)
(2)
t
WR
tEW
t
R/W
tDW
tDH
DATAIN
5621 drw 09
NOTES:
1. R/W or CE or UB and LB = VIH during all address transitions.
2. A write occurs during the overlap (tEW or tWP) of a CE = VIL and a R/W = VIL for memory array writing cycle.
3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle.
4. During this period, the I/O pins are in the output state and input signals must not be applied.
5. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state.
6. Timing depends on which enable signal is asserted last, CE or R/W.
7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load
(Figure 2).
8. If OE = VIL during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be
placed on the bus for the required tDW. If OE = VIH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the
specified tWP.
9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition.
12
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Semaphore Read after Write Timing, Either Side(1)
tSAA
A0-A2
VALID ADDRESS
VALID ADDRESS
tAW
tWR
t
ACE
t
EW
SEM/UB/LB(1)
tOH
tSOP
t
DW
OUT
DATA
VALID(2)
I/O
IN
DATA VALID
tAS
tWP
tDH
R/W
tSWRD
tAOE
OE
t
SOP
Write Cycle
Read Cycle
5621 drw 10
NOTES:
1. CE = VIH or UB and LB = VIH for the duration of the above timing (both write and read cycle) (Refer to Chip Enable Truth Table). Refer also to Truth Table II for appropriate
UB/LB controls.
2. "DATAOUT VALID" represents all I/O's (I/O0 - I/O17) equal to the semaphore value.
Timing Waveform of Semaphore Write Contention(1,3,4)
A0"A"-A2"A"
MATCH
(2)
SIDE "A"
R/W"A"
SEM"A"
tSPS
A0"B"-A2"B"
MATCH
(2)
SIDE
R/W"B"
SEM"B"
"B"
5621 drw 11
NOTES:
1. DOR = DOL = VIL, CEL = CER = VIH. Refer also to Truth Table II for appropriate UB/LB controls.
2. All timing is the same for left and right ports. Port "A" may be either left or right port. "B" is the opposite from port "A".
3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH.
4. If tSPS is not satisfied,the semaphore will fall positively to one side or the other, but there is no guarantee which side will be granted the semaphore flag.
13
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange
70V639S10
Com'l Only
70V639S12
Com'l
70V639S15
Com'l
& Ind
& Ind
Symbol
BUSY TIMING (M/S=VIH
Parameter
Unit
Min.
Max.
Min.
Max.
Min.
Max.
)
____
____
____
____
____
____
____
____
____
____
____
____
t
BAA
BDA
BAC
BDC
APS
BDD
WH
10
10
10
12
12
12
15
15
15
ns
ns
ns
ns
ns
ns
ns
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Disable Time from Chip Enable High
Arbitration Priority Set-up Time(2)
BUSY Disable to Valid Data(3)
Write Hold After BUSY(5)
t
t
t
10
____
12
____
15
____
t
5
____
5
____
5
____
t
10
____
12
____
15
____
t
8
10
12
BUSY TIMING (M/S=VIL
)
____
____
____
____
____
____
BUSY Input to Write(4)
Write Hold After BUSY(5)
t
WB
0
8
0
0
ns
ns
tWH
10
12
PORT-TO-PORT DELAY TIMING
____
____
____
____
____
____
t
WDD
Write Pulse to Data Delay(1)
Write Data Valid to Read Data Delay(1)
22
20
25
22
30
25
ns
tDDD
ns
5621 tbl 14
NOTES:
1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)".
2. To ensure that the earlier of the two ports wins.
3. tBDD is a calculated parameter and is the greater of the Max. spec, tWDD – tWP (actual), or tDDD – tDW (actual).
4. To ensure that the write cycle is inhibited on port "B" during contention on port "A".
5. To ensure that a write cycle is completed on port "B" after contention on port "A".
14
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
TimingWaveformof WritewithPort-to-PortReadandBUSY (M/S =VIH)(2,4,5)
tWC
MATCH
ADDR"A"
tWP
R/W"A"
tDW
t
DH
VALID
DATAIN "A"
(1)
tAPS
MATCH
ADDR"B"
t
BAA
tBDA
tBDD
BUSY"B"
tWDD
DATAOUT "B"
VALID
(3)
tDDD
.
5621 drw 12
NOTES:
1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (SLAVE).
2. CEL = CER = VIL.
3. OE = VIL for the reading port.
4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above.
5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A".
Timing Waveform of Write with BUSY (M/S = VIL)
tWP
R/W"A"
(3)
tWB
BUSY"B"
(1)
tWH
(2)
R/W"B"
5621 drw 13
NOTES:
1. tWH must be met for both BUSY input (SLAVE) and output (MASTER).
2. BUSY is asserted on port "B" blocking R/W"B", until BUSY"B" goes HIGH.
3. tWB is only for the 'slave' version.
15
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of BUSY Arbitration Controlled by CE Timing(M/S = VIH)(1)
ADDR"A"
ADDRESSES MATCH
and "B"
CE"A"
(2)
t
APS
CE"B"
t
BAC
tBDC
BUSY"B"
5621 drw 14
Waveform of BUSY Arbitration Cycle Controlled by Address Match
Timing(M/S = VIH)(1)
ADDR"A"
ADDRESS "N"
(2)
tAPS
ADDR"B"
MATCHING ADDRESS "N"
tBAA
tBDA
BUSY"B"
5621 drw 15
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted.
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange
70V639S10
Com'l Only
70V639S12
Com'l
70V639S15
Com'l
& Ind
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
INTERRUPT TIMING
____
____
____
____
____
____
t
AS
WR
INS
INR
Address Set-up Time
Write Recovery Time
Interrupt Set Time
0
0
0
ns
ns
ns
t
0
____
0
____
0
____
t
10
10
12
12
15
15
____
____
____
t
Interrupt Reset Time
ns
5621 tbl 15
16
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of Interrupt Timing(1)
tWC
INTERRUPT SET ADDRESS(2)
ADDR"A"
(4)
(3)
t
WR
t
AS
CE"A"
R/W"A"
INT"B"
(3)
t
INS
5621 drw 16
tRC
INTERRUPT CLEAR ADDRESS (2)
ADDR"B"
CE"B"
(3)
t
AS
OE"B"
(3)
tINR
INT"B"
5621 drw 17
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. Refer to Interrupt Truth Table.
3. Timing depends on which enable signal (CE or R/W) is asserted last.
4. Timing depends on which enable signal (CE or R/W) is de-asserted first.
Truth Table III — Interrupt Flag(1,4)
Left Port
OE
Right Port
OE
R/W
L
A16L-A0L
R/WR
A
16R-A0R
Function
Set Right INT Flag
Reset Right INT Flag
Set Left INT Flag
Reset Left INT Flag
CEL
L
INTL
CER
R
INTR
L
L
X
X
L
X
X
X
L
1FFFF
X
X
X
L(3)
H(2)
X
X
L
L
X
X
L
X
L(2)
H(3)
X
R
X
X
1FFFF
1FFFE
X
R
X
X
L
X
X
L
X
1FFFE
X
X
L
5621 tbl 16
NOTES:
1. Assumes BUSYL = BUSYR =VIH.
2. If BUSYL = VIL, then no change.
3. If BUSYR = VIL, then no change.
4. INTL and INTR must be initialized at power-up.
17
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table IV —
AddressBUSY Arbitration
Inputs
Outputs
A
-A
AOORL-A1166RL
Function
Normal
Normal
Normal
(1)
(1)
CE
L
CE
R
BUSY
L
BUSYR
X
H
X
L
X
X
H
L
NO MATCH
MATCH
H
H
H
H
MATCH
H
H
MATCH
(2)
(2)
Write Inhibit(3)
5621 tbl 17
NOTES:
1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT70V639
are push-pull, not open drain outputs. On slaves the BUSY input internally inhibits writes.
2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address
and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously.
3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored
when BUSYR outputs are driving LOW regardless of actual logic level on the pin.
Truth Table V — Example of Semaphore Procurement Sequence(1,2,3)
Functions
D0
- D17 Left
D0
- D17 Right
Status
No Action
1
0
0
1
1
0
1
1
1
0
1
1
1
1
0
0
1
1
0
1
1
1
Semaphore free
Left Port Writes "0" to Semaphore
Right Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "1" to Semaphore
Right Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
5621 tbl 18
NOTES:
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT70V639.
2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O17). These eight semaphores are addressed by A0 - A2.
3. CE = VIH, SEM = VIL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table.
FunctionalDescription
The IDT70V639 provides two ports with separate control, address
and I/O pins that permit independent access for reads or writes to any
locationinmemory.TheIDT70V639hasanautomaticpowerdownfeature
controlled by CE. The CE0 and CE1 control the on-chip power down
circuitrythatpermitstherespectiveporttogointoastandbymodewhen
not selected (CE =HIGH). Whenaportisenabled, accesstotheentire
memoryarrayispermitted.
3FFFE (HEX), where a write is defined as CER = R/WR = VIL per the
Truth Table. The left port clears the interrupt through access of
address location 3FFFE when CEL = OEL = VIL, R/W is a "don't care".
Likewise, the right port interrupt flag (INTR) is asserted when the left
port writes to memory location 3FFFF (HEX) and to clear the interrupt
flag (INTR), the right port must read the memory location 3FFFF. The
message (18 bits) at 3FFFE or 3FFFF is user-defined since it is an
addressable SRAM location. If the interrupt function is not used,
address locations 3FFFE and 3FFFF are not used as mail boxes, but
as part of the random access memory. Refer to Truth Table III for
theinterruptoperation.
Interrupts
If the user chooses the interrupt function, a memory location (mail
boxormessagecenter)isassignedtoeachport. Theleftportinterrupt
flag (INTL) is asserted when the right port writes to memory location
18
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
address signals only. It ignores whether an access is a read or write.
In a master/slave array, both address and chip enable must be valid
long enough for a BUSY flag to be output from the master before the
actual write pulse can be initiated with the R/W signal. Failure to
observe this timing can result in a glitched internal write inhibit signal
and corrupted data in the slave.
BusyLogic
BusyLogicprovidesahardwareindicationthatbothportsoftheRAM
haveaccessedthesamelocationatthesametime.Italsoallowsoneofthe
twoaccessestoproceedandsignalstheothersidethattheRAMis“Busy”.
TheBUSYpincanthenbeusedtostalltheaccessuntiltheoperationon
theothersideiscompleted.Ifawriteoperationhasbeenattemptedfrom
thesidethatreceivesaBUSYindication,thewritesignalisgatedinternally
topreventthewritefromproceeding.
Semaphores
TheuseofBUSYlogicisnotrequiredordesirableforallapplications.
InsomecasesitmaybeusefultologicallyORtheBUSYoutputstogether
and use any BUSY indication as an interrupt source to flag the event of
anillegalorillogicaloperation.IfthewriteinhibitfunctionofBUSYlogicis
notdesirable,theBUSYlogiccanbedisabledbyplacingthepartinslave
modewiththeM/Spin.OnceinslavemodetheBUSYpinoperatessolely
asawriteinhibitinputpin.Normaloperationcanbeprogrammedbytying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
The BUSY outputs on the IDT70V639 RAM in master mode, are
push-pull type outputs and do not require pull up resistors to operate.
If these RAMs are being expanded in depth, then the BUSY indication
for the resulting array requires the use of an external AND gate.
The IDT70V639 is an extremely fast Dual-Port 128K x 18 CMOS
Static RAM with an additional 8 address locations dedicated to binary
semaphore flags. These flags allow either processor on the left or right
side of the Dual-Port RAM to claim a privilege over the other processor
for functions defined by the system designer’s software. As an ex-
ample, the semaphore can be used by one processor to inhibit the
other from accessing a portion of the Dual-Port RAM or any other
shared resource.
The Dual-Port RAM features a fast access time, with both ports
being completely independent of each other. This means that the
activityontheleftportinnowayslowstheaccesstimeoftherightport.
Both ports are identical in function to standard CMOS Static RAM and
can be read from or written to at the same time with the only possible
conflict arising from the simultaneous writing of, or a simultaneous
READ/WRITE of, a non-semaphore location. Semaphores are pro-
tected against such ambiguous situations and may be used by the
system program to avoid any conflicts in the non-semaphore portion
of the Dual-Port RAM. These devices have an automatic power-down
feature controlled by CE, the Dual-Port RAM enable, and SEM, the
semaphore enable. The CE and SEM pins control on-chip power
down circuitry that permits the respective port to go into standby mode
whennotselected.
A17
CE0
CE0
MASTER
Dual Port RAM
SLAVE
Dual Port RAM
BUSY
R
BUSY
R
BUSY
L
BUSYL
CE1
CE1
MASTER
Dual Port RAM
SLAVE
Dual Port RAM
Systems which can best use the IDT70V639 contain multiple
processors or controllers and are typically very high-speed systems
which are software controlled or software intensive. These systems
can benefit from a performance increase offered by the IDT70V639s
hardware semaphores, which provide a lockout mechanism without
requiringcomplexprogramming.
BUSY
L
BUSY
L
BUSYR
BUSY
R
.
5621 drw 18
Figure 3. Busy and chip enable routing for both width and depth
expansion with IDT70V639 RAMs.
Softwarehandshakingbetweenprocessorsoffersthemaximumin
system flexibility by permitting shared resources to be allocated in
varying configurations. The IDT70V639 does not use its semaphore
flags to control any resources through hardware, thus allowing the
systemdesignertotalflexibilityinsystemarchitecture.
Width Expansion with Busy Logic
Master/SlaveArrays
When expanding an IDT70V639 RAM array in width while using
BUSY logic, one master part is used to decide which side of the RAMs
array will receive a BUSY indication, and to output that indication. Any
number of slaves to be addressed in the same address range as the
master use the BUSY signal as a write inhibit signal. Thus on the
IDT70V639 RAM the BUSY pin is an output if the part is used as a
master (M/S pin = VIH), and the BUSY pin is an input if the part used
as a slave (M/S pin = VIL) as shown in Figure 3.
An advantage of using semaphores rather than the more common
methods of hardware arbitration is that wait states are never incurred
in either processor. This can prove to be a major advantage in very
high-speedsystems.
How the Semaphore Flags Work
The semaphore logic is a set of eight latches which are indepen-
dent of the Dual-Port RAM. These latches can be used to pass a flag,
or token, from one port to the other to indicate that a shared resource
is in use. The semaphores provide a hardware assist for a use
assignmentmethodcalled“TokenPassingAllocation.”Inthismethod,
the state of a semaphore latch is used as a token indicating that a
shared resource is in use. If the left processor wants to use this
resource,itrequeststhetokenbysettingthelatch.Thisprocessorthen
If two or more master parts were used when expanding in width, a
splitdecisioncouldresultwithonemasterindicating BUSYononeside
of the array and another master indicating BUSY on one other side of
the array. This would inhibit the write operations from one port for part
of a word and inhibit the write operations from the other port for the
other part of the word.
The BUSY arbitration on a master is based on the chip enable and
19
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
question. Meanwhile, if a processor on the right side attempts to write
a zero to the same semaphore flag it will fail, as will be verified by the
fact that a one will be read from that semaphore on the right side
during subsequent read. Had a sequence of READ/WRITE been
usedinstead,systemcontentionproblemscouldhaveoccurredduring
the gap between the read and write cycles.
verifiesitssuccessinsettingthelatchbyreadingit. Ifitwassuccessful,it
proceeds to assume control over the shared resource. If it was not
successfulinsettingthelatch,itdeterminesthattherightsideprocessor
has set the latch first, has the token and is using the shared resource.
The left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore to
perform another task and occasionally attempt again to gain control of
the token via the set and test sequence. Once the right side has
relinquishedthetoken,theleftsideshouldsucceedingainingcontrol.
The semaphore flags are active LOW. A token is requested by
writing a zero into a semaphore latch and is released when the same
sidewritesaonetothatlatch.
It is important to note that a failed semaphore request must be
followed by either repeated reads or by writing a one into the same
location. The reason for this is easily understood by looking at the
simple logic diagram of the semaphore flag in Figure 4. Two sema-
phore request latches feed into a semaphore flag. Whichever latch is
first to present a zero to the semaphore flag will force its side of the
semaphore flag LOW and the other side HIGH. This condition will
The eight semaphore flags reside within the IDT70V639 in a
separate memory space from the Dual-Port RAM. This address space
isaccessedbyplacingalowinputontheSEMpin(whichactsasachip
select for the semaphore flags) and using the other control pins
(Address, CE, R/W and LB/UB) as they would be used in accessing a
standard Static RAM. Each of the flags has a unique address which
can be accessed by either side through address pins A0 – A2. When
accessing the semaphores, none of the other address pins has
anyeffect.
L PORT
R PORT
SEMAPHORE
REQUEST FLIP FLOP
SEMAPHORE
REQUEST FLIP FLOP
0
D
0
D
D
D
Q
Q
WRITE
WRITE
Whenwritingtoasemaphore,onlydatapinD0 isused.Ifalowlevel
is written into an unused semaphore location, that flag will be set to
a zero on that side and a one on the other side (see Truth Table V).
Thatsemaphorecannowonlybemodifiedbythesideshowingthezero.
When a one is written into the same location from the same side, the
SEMAPHORE
READ
SEMAPHORE
READ
5621 drw 19
Figure 4. IDT70V639 Semaphore Logic
flag will be set to a one for both sides (unless a semaphore request continue until a one is written to the same semaphore request latch.
fromtheothersideispending)andthencanbewrittentobybothsides. Should the other side’s semaphore request latch have been written to
The fact that the side which is able to write a zero into a semaphore a zero in the meantime, the semaphore flag will flip over to the other
subsequently locks out writes from the other side is what makes side as soon as a one is written into the first side’s request latch. The
semaphore flags useful in interprocessor communications. (A thor- second side’s flag will now stay LOWuntil its semaphore request latch
ough discussion on the use of this feature follows shortly.) A zero is written to a one. From this it is easy to understand that, if a
written into the same location from the other side will be stored in the semaphore is requested and the processor which requested it no
semaphore request latch for that side until the semaphore is freed by longer needs the resource, the entire system can hang up until a one
thefirstside.
When a semaphore flag is read, its value is spread into all data bits
iswrittenintothatsemaphorerequestlatch.
The critical case of semaphore timing is when both sides request
so that a flag that is a one reads as a one in all data bits and a flag a single token by attempting to write a zero into it at the same time. The
containing a zero reads as all zeros. The read value is latched into one semaphore logic is specially designed to resolve this problem. If
side’s output register when that side's semaphore, byte select (SEM, simultaneous requests are made, the logic guarantees that only one
LB/UB)andoutputenable(OE)signalsgoactive.Thisservestodisallow side receives the token. If one side is earlier than the other in making
thesemaphorefromchangingstateinthemiddleofareadcycleduetoa the request, the first side to make the request will receive the token. If
write cycle from the other side. Because of this latch, a repeated read bothrequestsarriveatthesametime, theassignmentwillbearbitrarily
of a semaphore in a test loop must cause either signal (SEM or OE) to made to one port or the other.
go inactive or the output will never change. However, during reads LB
andUBfunctiononlyasanoutputforsemaphore.Theydonothaveany semaphores alone do not guarantee that access to a resource is
influenceonthesemaphorecontrollogic.
secure. As with any powerful programming technique, if semaphores
A sequence WRITE/READ must be used by the semaphore in are misused or misinterpreted, a software error can easily happen.
order to guarantee that no system level contention will occur. A
One caution that should be noted when using semaphores is that
Initialization of the semaphores is not automatic and must be
processor requests access to shared resources by attempting to write handled via the initialization program at power-up. Since any sema-
a zero into a semaphore location. If the semaphore is already in use, phore request flag which contains a zero must be reset to a one,
the semaphore request latch will contain a zero, yet the semaphore all semaphores on both sides should have a one written into them
flag will appear as one, a fact which the processor will verify by the at initialization from both sides to assure that they will be free
subsequent read (see Table V). As an example, assume a processor when needed.
writes a zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written success-
fully to that location and will assume control over the resource in
20
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
JTAGTimingSpecifications
tJCYC
t
JR
tJF
tJCL
tJCH
TCK
Device Inputs(1)/
TDI/TMS
tJDC
tJS
tJH
Device Outputs(2)/
TDO
t
JRSR
tJCD
TRST
x
5621 drw 20
tJRST
NOTES:
1. Device inputs = All device inputs except TDI, TMS, and TRST.
2. Device outputs = All device outputs except TDO.
JTAG AC Electrical
Characteristics(1,2,3,4)
Symbol
Parameter
JTAG Clock Input Period
JTAG Clock HIGH
JTAG Clock Low
JTAG Clock Rise Time
JTAG Clock Fall Time
JTAG Reset
Min.
100
40
Max.
____
Units
ns
t
JCYC
JCH
JCL
JR
JF
JRST
JRSR
JCD
JDC
JS
JH
____
____
t
ns
t
40
____
ns
t
3(1)
3(1)
ns
____
t
ns
____
t
50
ns
____
t
JTAG Reset Recovery
JTAG Data Output
JTAG Data Output Hold
JTAG Setup
50
____
ns
t
25
____
ns
t
0
ns
____
____
t
15
15
ns
t
JTAG Hold
ns
5621 tbl 19
NOTES:
1. Guaranteed by design.
2. 30pF loading on external output signals.
3. Refer to AC Electrical Test Conditions stated earlier in this document.
4. JTAG operations occur at one speed (10MHz). The base device may run at
any speed specified in this datasheet.
21
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Identification Register Definitions
Instruction Field
Value
0x0
Description
Revision Number (31:28)
Reserved for version number
IDT Device ID (27:12)
0x30C
0x33
1
Defines IDT part number
IDT JEDEC ID (11:1)
Allows unique identification of device vendor as IDT
Indicates the presence of an ID register
ID Register Indicator Bit (Bit 0)
5621 tbl 20
ScanRegisterSizes
Register Name
Bit Size
Instruction (IR)
4
1
Bypass (BYR)
Identification (IDR)
Boundary Scan (BSR)
32
Note (3)
5621 tbl 21
SystemInterfaceParameters
Instruction
Code
Description
EXTEST
0000
Forces contents of the boundary scan cells onto the device outputs(1).
Places the boundary scan register (BSR) between TDI and TDO.
BYPASS
IDCODE
1111
Places the by pass registe r (BYR) between TDI and TDO.
0010
Loads the ID register (IDR) with the vendor ID code and places the
register between TDI and TDO.
0100
Places the bypass register (BYR) between TDI and TDO. Forces all
device output drivers to a High-Z state.
HIGHZ
Uses BYR. Forces contents of the boundary scan cells onto the device
outputs. Places the bypass register (BYR) between TDI and TDO.
CLAMP
0011
0001
SAMPLE/PRELOAD
Places the boundary scan register (BSR) between TDI and TDO.
SAMPLE allows data from device inputs(2) and outputs(1) to be captured
in the boundary scan cells and shifted serially through TDO. PRELOAD
allows data to be input serially into the boundary scan cells via the TDI.
RESERVED
All other codes
Several combinations are reserved. Do not use codes other than those
identified above.
5621 tbl 22
NOTES:
1. Device outputs = All device outputs except TDO.
2. Device inputs = All device inputs except TDI, TMS, and TRST.
3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local
IDT sales representative.
22
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Ordering Information
XXXXX
A
999
A
A
A
A
Device
Type
Power Speed
Package
Process/
Temperature
Range
Blank
8
Tube or Tray
Tape & Reel
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
Blank
I(1)
G(2)
Green
BF
PRF
BC
208-ball fpBGA (BF208)
128-pin TQFP (PK128)
256-ball BGA (BC256)
10
12
15
Commercial Only
Commercial & Industrial
Commercial & Industrial
Speed in nanoseconds
S
Standard Power
70V639
2304K (128K x 18) 3.3V Asynchronous Dual-Port RAM
5621 drw 21
NOTES:
1. Contactyour localsalesofficeforindustrialtemprangeforotherspeeds,packagesandpowers.
2. Greenpartsavailable.Forspecificspeeds,packagesandpowerscontactyourlocalsalesoffice.
DatasheetDocumentHistory
06/01/00:
08/07/00:
06/20/01:
Initial Public Offering
Pages 6,13 & 20 Inserted additional LB and UB information
Page 1 Added JTAG information for TQFP package
Page14 Increased BUSY TIMINGparameterstBDA,tBAC,tBDC andtBDD forallspeeds
Page21 Changed maximumvalueforJTAGACElectricalCharacteristicsfortJCD from20nsto25ns
Removed Preliminary status
10/25/04:
Addeddaterevisionforpinconfigurations
Page7 AddedJunctionTemptotheAbsoluteMaximumRatingstable
Updated Capacitance table
Page12UpdatedTimingWaveformofWriteCycleNo. 1, R/WControlledTiming
Page 1 & 23 Replaced old TM logo with new TM logo
Page 1 Added green availability to features
05/25/05:
07/25/08:
Page23Addedgreenindicatortoorderinginformation
Page 8 Corrected a typo in the DC Chars table
23
IDT70V639S
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
DatasheetDocumentHistory(con't)
01/19/09:
06/17/15:
Page 23 Removed "IDT" from orderable part number
Page 2 Correctedtexttypo
Page 2 , 3, 4 & 23 The package codes for BF-208 changed to BF208, PK-128 changed to PK128 & BC-256 changed to
BC256respectivelytomatchthestandardpackagecodes
Page 2 , 3 & 4 Removed the date from all of the pin configurations BF208, PK128 & BC256
Page 8 Correctedtypoincolumnheadingfor15nsI-tempoffering
Page 22 AddedT&RindicatorandindustrialtempfootnotetoOrderingInformation
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
for Tech Support:
408-284-2794
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
DualPortHelp@idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
24
相关型号:
©2020 ICPDF网 联系我们和版权申明