74FCT162244TEB
更新时间:2024-09-18 12:36:11
品牌:IDT
描述:FAST CMOS 16-BIT BUFFER/LINE DRIVER Reduced system switching noise
74FCT162244TEB 概述
FAST CMOS 16-BIT BUFFER/LINE DRIVER Reduced system switching noise FAST CMOS 16位缓冲器/线路驱动器降低系统的开关噪声
74FCT162244TEB 数据手册
通过下载74FCT162244TEB数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载FAST CMOS 16-BIT
BUFFER/LINE DRIVER
IDT54/74FCT162244T/AT/CT/ET
FEATURES:
DESCRIPTION:
• 0.5 MICRON CMOS Technology
• High-speed, low-power CMOS replacement for ABT functions
• Typical tSK(o) (Output Skew) < 250ps
• Low input and output leakage ≤ 1µA (max.)
• ESD > 2000V per MIL-STD-883, Method 3015; > 200V using
machine model (C = 200pF, R = 0)
• Balanced Output Drivers:
– ±24mA(industrial)
– ±16mA(military)
• Reduced system switching noise
• Typical VOLP (Output Ground Bounce) < 0.6V at VCC = 5V,
TA = 25°C
The FCT162244T 16-Bit Buffer/Line Driver is for bus interface or signal
bufferingapplicationsrequiringhighspeedandlowpowerdissipation. These
deviceshaveaflowthroughpinorganization,andshrinkpackagingtosimplify
boardlayout. Allinputsaredesignedwithhysteresisforimprovednoisemargin.
The three-state controls allow independent 4-bit, 8-bit or combined 16-bit
operation. Thesepartsarepluginreplacementsfor54/74ABT16244where
higher speed, lower noise or lower power dissipation levels are desired.
TheFCT162244Thas balancedoutputcurrentlevels andcurrentlimiting
resistors. Theseofferlowgroundbounce,minimalundershoot,andcontrolled
outputfalltimes,reducingtheneedforexternalseriesterminatingresistorswhile
still providing very high speed operation for loads of less than 200pF.
• Available in the following packages:
– Industrial: SSOP, TSSOP
– Military: CERPACK
FUNCTIONALBLOCKDIAGRAM
1OE
3OE
1
Y
1
1
1
A
1
2
3
A
1
3
Y
1
2
3A
3A
3A
2
3
Y
A
1
1
Y
2
3
3
4
1
1
A
3
4
Y
3
3
Y
3
4
A
Y
1
Y
4
2OE
4OE
2
Y
1
4
A
1
2
2
A
1
2
4
4
4
Y
Y
Y
1
2
3
4
4
4
A
2
2
2
A
2
2
2
Y
Y
Y
2
3
4
A
3
4
A
3
4
A
A
4
Y
4
TheIDTlogoisaregisteredtrademarkofIntegratedDeviceTechnology,Inc.
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
SEPTEMBER 2009
1
© 2009 Integrated Device Technology, Inc.
DSC-5461/9
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
ABSOLUTE MAXIMUM RATINGS(1)
PINCONFIGURATION
Symbol
Description
Max
Unit
V
(2)
VTERM
Terminal Voltage with Respect to GND
–0.5 to +7
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
(3)
1
OE
2
OE
VTERM
Terminal Voltage with Respect to GND –0.5 to VCC+0.5
V
TSTG
IOUT
Storage Temperature
DC Output Current
–65 to +150
–60 to +120
° C
mA
2
1
Y
1
2
1
A
1
2
3
1
Y
1
A
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
GND
4
GND
5
1
Y
3
4
1
1
A3
6
1
Y
A4
2. All device terminals except FCT162XXXT Output and I/O terminals.
3. Output and I/O terminals terminals for FCT162XXXT and FCT166XXXT.
V
CC
7
V
CC
8
2
2
Y
1
2
2
A1
CAPACITANCE (TA = +25°C, F = 1.0MHz)
Symbol
CIN
Parameter(1)
Input Capacitance
Output Capacitance
Conditions
VIN = 0V
Typ.
3.5
Max. Unit
9
2
A2
Y
6
8
pF
pF
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
GND
GND
COUT
VOUT = 0V
3.5
2
2
3
3
A3
A4
A1
A2
2
2
3
3
Y3
Y4
Y1
Y2
NOTE:
1. This parameter is measured at characterization but not tested.
PINDESCRIPTION
Pin Names
xOE
Description
3-State Output Enable Inputs (Active LOW)
Data Inputs
GND
GND
3
3
A3
3
3
Y
3
4
xAx
xYx
3-State Outputs
Y
A4
V
CC
V
CC
FUNCTIONTABLE(1)
4
A1
4
4
Y
1
2
Inputs
Outputs
4
A2
Y
xOE
L
xAx
L
xYx
L
GND
GND
4
4
A
3
4
4
4
Y
3
4
L
H
H
A
Y
H
X
Z
4OE
3OE
NOTE:
1. H = HIGH Voltage Level
X = Don’t Care
L = LOW Voltage Level
Z = High-Impedance
SSOP/ TSSOP/ CERPACK
TOP VIEW
2
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
DCELECTRICALCHARACTERISTICSOVEROPERATINGRANGE
FollowingConditionsApplyUnlessOtherwiseSpecified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±10%; Military: TA = –55°C to +125°C, VCC = 5.0V ±10%
Symbol
VIH
Parameter
Input HIGH Level
Test Conditions(1)
Min.
2
Typ.(2)
—
Max.
—
0.8
1
Unit
V
Guaranteed Logic HIGH Level
VIL
Input LOW Level
Guaranteed Logic LOW Level
VCC = Max.
—
—
—
—
—
—
—
—
–80
—
V
IIH
Input HIGH Current (Input pins)(5)
Input HIGH Current (I/O pins)(5)
Input LOW Current (Input pins)(5)
Input LOW Current (I/O pins)(5)
High Impedance Output Current
VI = VCC
—
µA
—
1
IIL
VI = GND
—
1
µA
—
1
IOZH
IOZL
VIK
IOS
VCC = Max.
VO = 2.7V
VO = 0.5V
—
1
(5)
(3-State Output pins)
—
1
Clamp Diode Voltage
Short Circuit Current
VCC = Min., IIN = –18mA
–0.7
–140
–1.2
–250
V
(3)
VCC = Max., VO = GND
mA
VH
Input Hysteresis
—
—
—
100
5
—
mV
µ A
ICCL
ICCH
ICCZ
Quiescent Power Supply Current
VCC = Max.
VIN = GND or VCC
500
OUTPUTDRIVECHARACTERISTICS
Symbol
IODL
Parameter
Output LOWCurrent
Output HIGH Current
OutputHIGHVoltage
Test Conditions(1)
Min.
60
Typ.(2)
Max.
200
Unit
mA
mA
V
(3)
VCC = 5V, VIN = VIH or VIL, VO = 1.5V
115
–115
3.3
(3)
IODH
VCC = 5V, VIN = VIH or VIL, VO = 1.5V
–60
2.4
–200
—
VOH
VCC = Min
IOH = –16mA MIL
VIN = VIH or VIL
VCC = Min
IOH = –24mA COM'L
IOH = 16mA MIL
VOL
Output LOWVoltage
—
0.3
0.55
V
VIN = VIH or VIL
IOH = 24mA COM'L
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. This test limit for this parameter is ±5µA at TA = –55°C.
3
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
POWERSUPPLYCHARACTERISTICS
Symbol
Parameter
Test Conditions(1)
Min.
Typ.(2)
Max.
Unit
ΔICC
Quiescent Power Supply Current
TTL Inputs HIGH
VCC = Max.
VIN = 3.4V
—
0.5
1.5
mA
(3)
ICCD
IC
Dynamic Power Supply
Current(4)
VCC = Max.
Outputs Open
xOE = GND
One Input Toggling
50% Duty Cycle
VIN = VCC
VIN = GND
—
60
100
µ A /
MHz
Total Power Supply Current(6)
VCC = Max.
Outputs Open
fi = 10MHz
VIN = VCC
VIN = GND
—
—
—
—
0.6
0.9
2.4
6.4
1.5
2.3
mA
50% Duty Cycle
xOE = GND
One Bit Toggling
VIN = 3.4V
VIN = GND
(5)
VCC = Max.
Outputs Open
fi = 2.5MHz
VIN = VCC
VIN = GND
4.5
(5)
50% Duty Cycle
xOE = GND
Sixteen Bits Toggling
VIN = 3.4V
VIN = GND
16.5
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ΔICC DHNT + ICCD (fCPNCP/2 + fiNi)
ICC = Quiescent Current (ICCL, ICCH and ICCZ)
ΔICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
NCP = Number of Clock Inputs at fCP
fi = Input Frequency
Ni = Number of Inputs at fi
4
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
SWITCHINGCHARACTERISTICSOVEROPERATINGRANGE
74FCT162244AT
74FCT162244CT
Min.(2)
Max.
74FCT162244ET
Min.(2)
Max.
Symbol
Parameter
Condition(1)
Min.(2)
Max.
Unit
tPLH
tPHL
Propagation Delay
xAx to xYx
CL = 50pF
RL = 500Ω
1.5
1.5
1.5
—
4.8
1.5
1.5
1.5
—
4.1
5.8
5.2
0.5
1.5
1.5
1.5
—
3.2
4.4
3.6
0.5
ns
tPZH
tPZL
Output Enable Time
6.2
5.6
0.5
ns
ns
ns
tPHZ
tPLZ
Output Disable Time
(3)
tSK(o)
Output Skew
54FCT162244T
54FCT162244AT
Min.(2)
Max.
54FCT162244CT
Symbol
Parameter
Condition(1)
Min.(2)
Max.
Min.(2)
Max.
Unit
tPLH
tPHL
Propagation Delay
xAx to xYx
CL = 50pF
RL = 500Ω
1.5
7
1.5
1.5
1.5
—
5.1
6.5
5.9
0.5
1.5
1.5
1.5
—
4.6
ns
tPZH
tPZL
Output Enable Time
1.5
1.5
—
8.5
7.5
0.5
6.5
5.7
0.5
ns
ns
ns
tPHZ
tPLZ
Output Disable Time
(3)
tSK(o)
Output Skew
NOTES:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design.
5
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
TESTCIRCUITSANDWAVEFORMS
SWITCHPOSITION
Test
Switch
Closed
Open
Open Drain
Disable Low
Enable Low
V
CC
7.0V
500Ω
500Ω
All Other Tests
V
OUT
V
IN
Pulse
Generator
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
D.U.T.
50pF
RT
CL
Test Circuit for All Outputs
3V
DATA
1.5V
INPUT
0V
LOW-HIGH-LOW
tH
tSU
1.5V
PULSE
3V
1.5V
0V
TIMING
INPUT
tW
ASYNCHRONOUS CONTROL
tREM
PRESET
3V
1.5V
0V
CLEAR
HIGH-LOW-HIGH
PULSE
1.5V
ETC.
SYNCHRONOUS CONTROL
PRESET
3V
1.5V
0V
CLEAR
tSU
Pulse Width
tH
CLOCK ENABLE
ETC.
Set-up, Hold, and Release Times
ENABLE
DISABLE
3V
1.5V
0V
3V
SAME PHASE
CONTROL
INPUT
1.5V
0V
INPUT TRANSITION
t
PLH
t
PHL
PHL
t
PZL
tPLZ
VOH
OUTPUT
3.5V
1.5V
3.5V
1.5V
OUTPUT
NORMALLY
LOW
SWITCH
CLOSED
VOL
tPLH
t
0.3V
0.3V
VOL
3V
1.5V
0V
tPZH
tPHZ
OPPOSITE PHASE
INPUT TRANSITION
VOH
OUTPUT
NORMALLY
HIGH
SWITCH
OPEN
1.5V
0V
0V
Propagation Delay
Enable and Disable Times
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
6
IDT54/74FCT162244T/AT/CT/ET
FASTCMOS16-BITBUFFER/LINEDRIVER
MILITARYANDINDUSTRIALTEMPERATURERANGES
ORDERINGINFORMATION
XX
FCT
XXXX
XXX
XX
X
Temp. Range
Family
Package
Process
Device Type
Blank
B
Industrial
MIL-STD-883, Class B
Industrial Options
Shrink Small Outline Package - Green
Thin Shrink Small Outline Package - Green
PVG
PAG
Military Options
CERPACK
E
16-Bit Buffer/Line Driver
244T
244AT
244CT
244ET
162
Double-Density, 5 Volt, Balanced Drive
54
74
55 C to +125 C
40 C to +85 C
DatasheetDocumentHistory
09/06/09 Pg.6
Updatedthe orderinginformationbyremovingthe "IDT"notationandnonRoHSpart.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
for Tech Support:
logichelp@idt.com
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
7
74FCT162244TEB 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
74FCT162244TPAGB | IDT | FAST CMOS 16-BIT BUFFER/LINE DRIVER Reduced system switching noise | 获取价格 | |
74FCT162244TPVCG4 | TI | 16-Bit Buffers/Line Drivers | 获取价格 | |
74FCT162244TPVGB | IDT | FAST CMOS 16-BIT BUFFER/LINE DRIVER Reduced system switching noise | 获取价格 | |
74FCT162244T_09 | IDT | FAST CMOS 16-BIT BUFFER/LINE DRIVER Reduced system switching noise | 获取价格 | |
74FCT162245ATE | IDT | Bus Transceiver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, CDFP48 | 获取价格 | |
74FCT162245ATPACT | TI | 16-bIT TRANSCEI | 获取价格 | |
74FCT162245ATPAG | ROCHESTER | FCT SERIES, DUAL 8-BIT TRANSCEIVER, TRUE OUTPUT, PDSO48, GREEN, TSSOP-48 | 获取价格 | |
74FCT162245ATPAG8 | IDT | 16-Bit Bi-Directional Transceiver, TSSOP0/Reel | 获取价格 | |
74FCT162245ATPAGB | IDT | Bus Transceiver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, GREEN, TSSOP-48 | 获取价格 | |
74FCT162245ATPVCG4 | TI | 16-Bit Transceivers | 获取价格 |
74FCT162244TEB 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6