IDT70V639S15PRFG [IDT]
Dual-Port SRAM, 128KX18, 15ns, CMOS, PQFP128, 14 X 20 MM, 1.40 MM HEIGHT, GREEN, TQFP-128;型号: | IDT70V639S15PRFG |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Dual-Port SRAM, 128KX18, 15ns, CMOS, PQFP128, 14 X 20 MM, 1.40 MM HEIGHT, GREEN, TQFP-128 |
文件: | 总23页 (文件大小:187K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PRELIMINARY
IDT70V639S
HIGH-SPEED 3.3V 128K x 18
ASYNCHRONOUS DUAL-PORT
STATIC RAM
Features
◆
True Dual-Port memory cells which allow simultaneous
access of the same memory location
High-speed access
◆
◆
Fully asynchronous operation from either port
Separate byte controls for multiplexed bus and bus
matching compatibility
Supports JTAG features compliant to IEEE 1149.1
– Due to limited pin count, JTAG is not supported on the
128-pin TQFP package.
◆
– Commercial:10/12/15ns (max.)
– Industrial:12/15ns (max.)
Dual chip enables allow for depth expansion without
external logic
IDT70V639 easily expands data bus width to 36 bits or
more using the Master/Slave select when cascading more
than one device
M/S = VIH for BUSY output flag on Master,
M/S = VIL for BUSY input on Slave
Busy and Interrupt Flags
◆
◆
◆
◆
◆
◆
◆
LVTTL-compatible, single 3.3V (±150mV) power supply for
core
LVTTL-compatible, selectable 3.3V (±150mV)/2.5V (±100mV)
power supply for I/Os and control signals on each port
Available in a 128-pin Thin Quad Flatpack, 208-ball fine
pitch Ball Grid Array, and 256-ball Ball Grid Array
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
◆
◆
◆
◆
On-chip port arbitration logic
Full on-chip hardware support of semaphore signaling
between ports
Functional Block Diagram
UB
L
L
R
UB
LB
LB
R
W
L
R/
R/
WR
B
B
E
1
L
B
E
1
B
E
0
E
0
L
CE0L
CE0R
R
R
CE1L
CE1R
OEL
OER
Dout0-8_L
Dout9-17_L
Dout0-8_R
Dout9-17_R
128K x 18
MEMORY
ARRAY
Din_L
I/O0L- I/O17L
Din_R
I/O0R - I/O17R
16R
0R
A
16L
0L
Address
Decoder
Address
Decoder
A
ADDR_L
ADDR_R
A
A
OE
L
OER
ARBITRATION
INTERRUPT
SEMAPHORE
LOGIC
0R
CE
0L
1L
CE
CE
1R
CE
R/
W
L
R/
WR
BUSY
SEM
INT
R
BUSY
SEM
INT
L
L
M/
S
R
L
R
TMS
TCK
TDI
JTAG
TDO
TRST
5621 drw 01
NOTES:
1. BUSY is an input as a Slave (M/S=VIL) and an output when it is a Master (M/S=VIH).
2. BUSY and INT are non-tri-state totem-pole outputs (push-pull).
JUNE 2001
1
DSC-5621/3
©2001IntegratedDeviceTechnology,Inc.
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Description
TheIDT70V639isahigh-speed128Kx18AsynchronousDual-Port address,andI/Opinsthatpermitindependent,asynchronousaccessfor
Static RAM. The IDT70V639 is designed to be used as a stand-alone reads or writes to any location in memory. An automatic power down
2304K-bitDual-PortRAMoras acombinationMASTER/SLAVEDual- feature controlled by the chip enables (either CE0 or CE1) permit the
Port RAM for 36-bit-or-more word system. Using the IDT MASTER/ on-chip circuitry of each port to enter a very low standby power mode.
SLAVE Dual-Port RAM approach in 36-bit or wider memory system
The70V639cansupportanoperatingvoltageofeither3.3Vor2.5V
applicationsresultsinfull-speed,error-freeoperationwithouttheneedfor on one or both ports, controlled by the OPT pins. The power supply for
additionaldiscretelogic.
the core ofthe device (VDD)remains at3.3V.
This device provides two independent ports with separate control,
PinConfigurations(1,2,3,4)
1
2
3
4
5
6
7
8
9
11 12 13 14
10
16 17
15
SS
16L
13L
A
12L
8L
V
V
V
DD
SS
SS
0L
SS
V
A
B
C
D
E
F
I/O9L
NC
V
A
A
NC
4L
A
A
L
NC
I/O8L
NC
L
INT
L
OPT
TDO
SEM
NC
A
B
C
D
E
F
SS
9L
A
NC
V
NC
A
5L
TDI
1L
DDQR
NC
NC
A
NC
UBL
LBL
A
V
NC
CE
0L
V
SS
BUSYL
A
A
10L
V
SS
DDQL
I/O
9R
V
DDQR
V
DD
A
14L
CE1L
A
6L
A
2L
V
DD
I/O8R
V
WL
R /
NC
V
SS
I/O10L
15L
11L
7L
DD
DDQL
A
A
V
NC
V
I/O
7L
I/O
7R
NC
A3L
V
DD
NC
OEL
V
DDQR I/O10R
I/O11L
NC
NC
NC
I/O6L
V
SS
V
DDQL
V
SS
6R
I/O11R
I/O
V
DDQR
V
SS
NC
NC
NC
SS
12L
DDQL
V
I/O
NC
V
I/O
5L
G
H
J
NC
NC
G
H
J
70V639BF
BF-208(5)
V
DD
NC
V
DDQR
DD
V
12R
I/O
NC
SS
V
5R
I/O
V
DD
V
DDQL
SS
V
V
SS
V
DDQR
V
DD
V
SS
V
SS
208-Ball BGA
Top View(6)
V
DDQL
I/O3R
NC
4R
V
SS
I/O
I/O14R
NC
V
SS
I/O13R
K
L
V
SS
K
L
I/O14L
V
DDQR
I/O13L
I/O3L
NC
V
SS
I/O4L
V
DDQL
I/O15R
NC
V
SS
NC
V
SS
I/O2R
NC
V
DDQR
M
N
P
R
T
M
N
P
R
T
NC
SS
V
15L
DDQL
1L
I/O
I/O1R
NC
V
I/O2L
NC
16R
I/O
16L
I/O
DDQR
DD
R
4R
I/O
SS
V
V
16R
12R
8R
A
V
INT
A
NC
A
A
TRST
NC
SEM
R
V
SS
V
DDQL
I/O0R
V
DDQR
V
V
SS
SS
A
5R
A
1R
2R
A
A
13R
14R
A
9R
NC
UBR
LBR
CE0R
TCK
NC
NC
V
SS
NC
I/O17R
BUSY
R
V
SS
V
SS
A
NC
NC
A
A
6R
A
10R
CE1R
WR
R/
NC
I/O17L
NC
V
DDQL TMS
V
DD
OPT
R
NC
I/O0L
V
DD
3R
A
0R
A
11R
A
7R
S
M/
V
SS
V
DD
OER
NC
A
15R
U
U
5621 tbl 02b
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is
set to VIL (0V).
3. All VSS pins must be connected to ground.
4. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
2
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Pin Configurations(1,2,3,4,7) (con't.)
A
A
OPTL
1L
1
2
3
4
5
6
7
8
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
A
14L
0L
A15L
A16L
NC
IO
IO
VSS
IO
8L
9L
9R
IO8R
NC
V
DDQL
V
SS
V
IO10L
SS
VDDQL
IO7L
IO
9
10
IO
10R
7R
V
DDQR
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
V
V
SS
V
SS
DDQR
IO11L
IO
IO
IO
IO
6L
6R
5L
5R
IO
11R
IO
12L
IO
12R
V
V
V
VSS
IO13R
IO13L
DD
70V639PRF
PK-128(5)
VDD
DD
V
DD
V
SS
V
SS
SS
IO4R
IO4L
IO3R
IO
IO
IO
128-Pin TQFP
Top View(6)
IO
14R
IO
14L
3L
2R
2L
IO15R
IO
15L
V
27
28
29
30
31
32
33
34
35
36
37
38
DDQL
V
SS
V
DDQL
V
SS
IO16R
IO16L
IO
IO
1R
1L
V
DDQR
V
V
SS
DDQR
VSS
IO
17R
IO
IO
OPT
A0R
A1R
0R
IO
17L
0L
NC
R
A
16R
A15R
A
14R
.
5621 drw 02a
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is
set to VIL (0V).
3. All VSS pins must be connected to ground.
4. Package body is approximately 14mm x 20mm x 1.4mm.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
7. Due to the restricted number of pins, JTAG is not supported in the PK-128 package.
3
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Pin Configuration(1,2,3,4) (con't.)
70V639BC
BC-256(5)
256-Pin BGA
Top View(6)
A1
A2
A3
A6
A7
A8
A9
A11
A12
A13
A14
A4
A5
A10
A15
A16
NC
TDI
NC
A11L
A8L
NC CE1L
A5L
A2L
A0L
INTL
NC
A14L
NC
NC
OEL
B1
B2
B3
B6
B7
B9
CE0L
B11
B12
B13
B4
B5
B8
B10
B14
B15
B16
NC
NC TDO
A12L
A9L
NC
A4L
A1L
NC
A15L
R/
NC
NC
NC
UBL
WL
C1
C5
C6
C2
C3
C4
C7
C8
C9
C10
C11
C12
C13
C16
C14
C15
NC
A13L
A10L
I/O9L VSS A16L
A7L
NC
A6L
A3L
I/O8L
LBL SEML BUSY
L
OPTL NC
D1
D2
D6
D9
D11
D3
D5
D7
D8
D10
D12
D13
D14
D15
D16
D4
NC I/O9R
VDDQL
VDDQL
VDDQR
NC
VDDQL
VDDQR VDDQR
VDDQL
VDDQR VDD
NC
NC I/O8R
VDD
E5
E6
E7
E8
E9
E10
E11
E12
E13
E1
E2
E3
E4
E14
E16
E15
VDD VDD
VSS
VSS
VSS
VSS
VDD
VDD VDDQR
I/O10R I/O10L NC VDDQL
NC
I/O7R
I/O7L
F7
F5
F6
F9
F10
F1
F2
F3
F11
F13
F14
F15
F16
F8
F12
F4
VSS
I/O11L NC I/O11R
VDD VSS
VSS
VSS
I/O6R NC I/O6L
VDDQR
VSS
VDDQL
VSS
VDD
G1
G5
G2
G4
G6
G8
G9
G3
G14
G15
G16
G7
G10
G12
G13
G11
NC
VSS
NC
VDDQR
VSS
VSS
VSS
I/O12L
I/O5L NC
NC
VSS
VSS
VSS
VDDQL
VSS
H11
H12
H16
H13
H7
H8
H9
H10
H14
H15
H5
H6
H3
H4
H1
H2
VSS VSS
I/O5R
VDDQL
VSS VSS
VSS
VSS
NC
NC
NC VDDQR VSS
VSS
NC I/O12R
J1
J2
J3
J4
J5
J6
J7
J8
J9
J13
J10
J11
J12
J14
J15
J16
I/O13L
VSS
I/O14R I/O13R VDDQL
VSS
VSS
VSS
VSS
VDDQR
VSS
VSS
VSS
I/O4R
I/O3R I/O4L
K6
K8
K10
K12
K13
K2
K4
K5
K7
K9
K11
K15
K16
K1
K3
K14
VSS
VSS
VSS
VSS
VDDQR
NC
VDDQL VSS
VSS
VSS
VSS
NC I/O3L
NC
I/O14L
NC
L7
L8
L11
L12
L13
L5
L6
L9
L10
L3
L4
L15
L16
L1
L2
L14
VSS
VSS
VSS VDD
VDDQL
I/O15R VDDQR VDD
VSS
VSS
VSS
NC I/O2R
I/O15L NC
I/O2L
M5
M6
M7
M8
M9
M10
M11
M12
M13
M1
M2
M3
M4
M16
M14
M15
VDD VDD
VSS
VSS
VSS
VSS
VDD VDD
VDDQL
I/O16R I/O16L NC VDDQR
NC
I/O1R I/O1L
N8
N12
N13
N16
N4
N5
N6
N7
N9
N10
N11
N15
N1
N2
N3
N14
VDDQL
VDDQL
NC
VDD
VDD VDDQR VDDQR VDDQL
VDDQR VDDQR VDDQL
I/O0R
NC I/O17R NC
NC
P1
P2
P3
P4
P5
P7
P8
P9
P10
P11
P12
P14
P15
P16
P6
P13
NC I/O17L TMS A16R A13R
A7R
NC
A6R
NC
NC
I/O0L
LBR SEMR BUSY
R
A10R
A3R
R5
R6
R7
R8
R9
R10
R11
R16
R1
R2
R3
R4
R12
R13
R14
R15
,
A15R A12R A9R
R/
M/
S
NC
UBR CE0R
WR
NC
NC
NC
A4R
A1R OPTR
TRST
NC
T2
T3
T1
T4
T5
T8
T9
T15
T16
T6
T7
T10
T11
T12
T13
T14
TCK
NC
NC
NC
A14R
NC
CE1R
NC
NC
A11R
A8R
R
R
INT
A5R
A2R
A0R
OE
5621 drw 02c
NOTES:
1. All VDD pins must be connected to 3.3V power supply.
2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V), and 2.5V if OPT pin for that port is
set to VIL (0V).
,
3. All VSS pins must be connected to ground supply.
4. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch.
5. This package code is used to reference the package diagram.
6. This text does not indicate orientation of the actual part-marking.
4
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
PinNames
Left Port
Right Port
Names
Chip Enables
CE0L CE1L
CE0R CE1R
,
,
R/WL
R/WR
Read/Write Enable
Output Enable
OEL
OER
A0L - A16L
I/O0L - I/O17L
A0R - A16R
I/O0R - I/O17R
Address
Data Input/Output
Semaphore Enable
Interrupt Flag
SEML
INTL
SEMR
INTR
Busy Flag
BUSYL
UBL
BUSYR
UBR
Upper Byte Select
Lower Byte Select
Power (I/O Bus) (3.3V or 2.5V)(1)
LBL
LBR
VDDQ L
OPTL
VDDQR
OPTR
(1,2)
Option for selecting VDDQX
M/S
Master or Slave Select
Power (3.3V)(1)
VDD
VSS
Ground (0V)
NOTES:
1. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to
applying inputs on I/OX.
TDI
Test Data Input
2. OPTX selects the operating voltage levels for the I/Os and controls on that port.
If OPTX is set to VIH (3.3V), then that port's I/Os and controls will operate at 3.3V
levels and VDDQX must be supplied at 3.3V. If OPTX is set to VIL (0V), then that
port's I/Os and controls will operate at 2.5V levels and VDDQX must be supplied
at 2.5V. The OPT pins are independent of one another—both ports can operate
at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V
with the other at 2.5V.
TDO
TCK
TMS
TRST
Test Data Output
Test Logic Clock (10MHz)
Test Mode Select
Reset (Initialize TAP Controller)
5621 tbl 01
5
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table IRead/Write and Enable Control(1)
Byte 1
Byte 0
1
W
9-17
0-8
I/O
CE
R/
I/O
MODE
Deselected–Power Down
Deselected–Power Down
Both Bytes Deselected
Write to Byte 0 Only
Write to Byte 1 Only
Write to Both Bytes
OE
X
X
X
X
X
X
L
SEM
H
CE0
H
X
L
UB
X
X
H
H
L
LB
X
X
H
L
X
L
X
High-Z
High-Z
High-Z
High-Z
DIN
High-Z
High-Z
High-Z
DIN
H
X
X
L
H
H
H
H
H
H
H
H
H
H
L
H
L
H
L
L
High-Z
DIN
H
L
L
L
DIN
H
L
H
L
L
H
H
H
X
High-Z
DOUT
DOUT
Read Byte 0 Only
L
H
L
H
L
High-Z
DOUT
Read Byte 1 Only
L
H
L
L
DOUT
Read Both Bytes
H
H
L
L
L
High-Z
High-Z
Outputs Disabled
5621 tbl 02
NOTE:
1. "H" = VIH, "L" = VIL, "X" = Don't Care.
Truth Table II Semaphore Read/Write Control(1)
Inputs(1)
Outputs
(2)
R/W
H
I/O1-17
I/O0
Mode
Read Data in Semaphore Flag(3)
Write I/O0 into Semaphore Flag
Not Allowed
CE
OE
UB
L
LB
L
SEM
L
H
L
X
X
DATAOUT
DATAOUT
H
L
X
L
L
X
DATAIN
↑
______
______
X
X
X
L
5621 tbl 03
NOTE:
1. There are eight semaphore flags written to I/O0 and read from all the I/Os (I/O0-I/O17). These eight semaphore flags are addressed by A0-A2.
2. CE = L occurs when CE0 = VIL and CE1 = VIH.
3. Each byte is controlled by the respective UB or LB. To read data UB and/or LB = VIL.
6
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
RecommendedOperating
TemperatureandSupplyVoltage(1)
RecommendedDCOperating
Conditions with VDDQ at 2.5V
Symbol
Parameter
Core Supply Voltage
I/O Supply Voltage(3)
Ground
Min. Typ.
Max.
3.45
2.6
0
Unit
V
Ambient
Grade
Commercial
Temperature
0OC to +70OC
-40OC to +85OC
GND
0V
VDD
VDD
3.15 3.3
3.3V + 150mV
3.3V + 150mV
VDDQ
VSS
2.4
0
2.5
V
Industrial
0V
0
V
5621 tbl 04
(2)
Input High Voltage(3)
1.7
V
____
VDDQ + 100mV
VIH
NOTE:
(Address & Control Inputs)
1. This is the parameter TA. This is the "instant on" case temperature.
(3)
(2)
____
____
VIH
VIL
Input High Voltage - I/O
1.7
VDDQ + 100mV
V
Input Low Voltage
-0.5(1)
0.7
V
5621 tbl 06
NOTES:
1. VIL > -1.5V for pulse width less than 10 ns.
2. VTERM must not exceed VDDQ + 100mV.
AbsoluteMaximumRatings(1)
3. To select operation at 2.5V levels on the I/Os and controls of a given port, the
OPTpinforthatportmustbesettoVIL (0V),andVDDQX forthatportmustbesupplied
as indicated above.
Symbol
Rating
Commercial
& Industrial
Unit
(2)
VTE RM
Terminal Voltage
with Respect to
GND
-0.5 to +4.6
V
Temperature
Under Bias
-55 to +125
-65 to +150
50
oC
oC
TBIAS
RecommendedDCOperating
Conditions with VDDQ at 3.3V
Storage
Temperature
TSTG
Symbol
Parameter
Core Supply Voltage
I/O Supply Voltage(3)
Ground
Min. Typ.
3.15 3.3
3.15 3.3
Max.
3.45
3.45
0
Unit
V
IOUT
DC Output Current
mA
VDD
5621 tbl 05
VDDQ
VSS
V
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VTERM must not exceed VDD + 150mV for more than 25% of the cycle time or
4ns maximum, and is limited to < 20mA for the period of VTERM > VDD + 150mV.
0
0
V
(2)
____
Input High Voltage
(Address & Control Inputs)
2.0
VDDQ + 150mV
V
VIH
(3)
(3)
____
____
(2)
VIH
Input High Voltage - I/O
2.0
VDDQ + 150mV
V
V
IL
Input Low Voltage
-0.3(1)
0.8
V
5621 tbl 07
NOTES:
1. VIL > -1.5V for pulse width less than 10 ns.
2. VTERM must not exceed VDDQ + 150mV.
3. To select operation at 3.3V levels on the I/Os and controls of a given port, the
OPT pin for that port must be set to VIH (3.3V), and VDDQX for that port must be
supplied as indicated above.
Capacitance(1)
(TA = +25°C, F = 1.0MHZ) TQFP ONLY
Symbol
Parameter
Input Capacitance
Output Capacitance
Conditions(2 )
Max. Unit
CIN
VIN = 3dV
8
pF
(3 )
COUT
VOUT = 3dV
10.5
pF
5621 tbl 08
NOTES:
1. These parameters are determined by device characterization, but are not
production tested.
2. 3dV references the interpolated capacitance when the input and output switch
from 0V to 3V or from 3V to 0V.
3. COUT also references CI/O.
7
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V ± 150mV)
70V639S
Max.
Symbol
|ILI|
Parameter
Test Conditions
VDDQ = Max., VIN = 0V to VDDQ
Min.
Unit
µA
µA
V
(1)
___
Input Leakage Current
10
10
___
___
|ILO|
Output Leakage Current
CE0 = VIH or CE1 = VIL, VOUT = 0V to VDDQ
IOL = +4mA, VDDQ = Min.
VOL (3.3V) Output Low Voltage(2)
VOH (3.3V) Output High Voltage(2)
VOL (2.5V) Output Low Voltage(2)
VOH (2.5V) Output High Voltage(2)
0.4
___
IOH = -4mA, VDDQ = Min.
2.4
V
___
IOL = +2mA, VDDQ = Min.
0.4
V
___
IOH = -2mA, VDDQ = Min.
2.0
V
5621 tbl 09
NOTE:
1. At VDD < - 2.0V input leakages are undefined.
2. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(3) (VDD = 3.3V ± 150mV)
70V639S10
Com'l Only
70V639S12
Com'l
70V639S15
Com'l
& Ind
& Ind
Symbol
Parameter
Test Condition
CEL and CER= V ,
Version
COM'L
Typ.(4)
340
Max. Typ.(4)
Max. Typ.(4)
Max. Unit
I
DD
Dynamic Operating
Current (Both
Ports Active)
mA
440
IL
S
S
S
S
S
S
S
S
S
S
500
315
365
90
465
515
125
150
325
365
15
300
350
Outputs Disabled,
____
____
(1)
IND
490
f = f
MAX
I
Standby Current
(Both Ports - TTL
Level Inputs)
mA
100
SB1
CE = CE = V
IH
COM'L
IND
115
165
75
L
R
(1)
f = f
MAX
____
____
100
115
200
225
3
125
(5)
I
Standby Current
(One Port - TTL
Level Inputs)
mA
315
SB2
CE = V and CE = V
"A"
IL
"B"
IH
COM'L
IND
225
340
175
200
Active Port Outputs Disabled,
____
____
(1)
350
f=f
MAX
I
Full Standby Current Both Ports CE and
mA
15
SB3
L
COM'L
IND
3
15
3
(Both Ports - CMOS CE > V - 0.2V, V > V - 0.2V
R
DD
IN
DD
____
____
or V < 0.2V, f = 0(2)
6
15
6
15
Level Inputs)
IN
(5)
I
Full Standby Current
(One Port - CMOS
Level Inputs)
mA
310
SB4
CE
CE
"B"
< 0.2V and
> V - 0.2V COM'L
220
335
195
220
320
360
170
195
"A"
DD
V > V - 0.2V or V < 0.2V, Active
IN
DD
IN
____
____
(1)
IND
345
Port, Outputs Disabled, f = f
MAX
5621 tbl 10
NOTES:
1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, using "AC TEST CONDITIONS" at input
levels of GND to 3V.
2. f = 0 means no address or control lines change. Applies only to input at CMOS level standby.
3. Port "A" may be either left or right port. Port "B" is the opposite from port "A".
4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. IDD DC(f=0) = 120mA (Typ).
5. CEX = VIL means CE0X = VIL and CE1X = VIH
CEX = VIH means CE0X = VIH or CE1X = VIL
CEX < 0.2V means CE0X < 0.2V and CE1X > VCC - 0.2V
CEX > VCC - 0.2V means CE0X > VCC - 0.2V or CE1X - 0.2V
"X" represents "L" for left port or "R" for right port.
8
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Test Conditions (VDDQ - 3.3V/2.5V)
2.5V
Input Pulse Levels
GND to 3.0V / GND to 2.5V
2ns Max.
Input Rise/Fall Times
Input Timing Reference Levels
Output Reference Levels
Output Load
833Ω
1.5V/1.25V
1.5V1.25V
DATAOUT
Figures 1 and 2
5621 tbl 11
5pF*
770Ω
,
Figure 2. Output Test Load
3.3V
590Ω
5pF*
50Ω
50Ω
,
OUT
DATA
OUT
DATA
1.5V/1.25
10pF
435Ω
(Tester)
5621 drw 03
Figure 1. AC Output Test load.
,
5621 drw 04
Figure 2. Output Test Load
(For tCKLZ, tCKHZ, tOLZ, and tOHZ).
*Including scope and jig.
10.5pF is the I/O capacitance of this
device, and 10pF is the AC Test Load
Capacitance.
7
6
5
4
3
∆tAA
(Typical, ns)
2
1
•
•
•
•
,
20.5
50
80 100
200
30
-1
Capacitance (pF)
5621 drw 05
Figure 3. Typical Output Derating (Lumped Capacitive Load).
9
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(5)
70V639S10
Com'l Only
70V639S12
Com'l
& Ind
70V639S15
Com'l
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
____
tRC
Read Cycle Time
10
12
15
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
____
____
____
tAA
Address Access Time
10
10
5
12
12
6
15
15
7
Chip Enable Access Time(3)
Byte Enable Access Time(3)
Output Enable Access Time
____
____
____
____
____
____
____
____
____
tACE
tABE
tAOE
tOH
tLZ
5
6
7
____
____
____
Output Hold from Address Change
Output Low-Z Time(1,2)
3
0
0
3
0
0
3
0
0
____
____
____
tHZ
Output High-Z Time(1,2)
4
6
8
tPU
tPD
tSOP
tSAA
Chip Enable to Power Up Time(2)
Chip Disable to Power Down Time(2)
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
0
0
0
____
____
____
____
____
____
10
4
10
6
15
8
____
____
____
3
10
3
12
3
20
ns
5621 tbl 12
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltage(5)
70V639S10
Com'l Only
70V639S12
Com'l
& Ind
70V639S15
Com'l
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
tWC
tEW
tAW
tAS
Write Cycle Time
10
8
12
10
10
0
15
12
12
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
Write Pulse Width
8
0
tWP
8
10
0
12
0
tWR
tDW
tDH
Write Recovery Time
Data Valid to End-of-Write
Data Hold Time(4)
0
6
8
10
0
0
0
(1,2)
____
____
____
tWZ
Write Enable to Output in High-Z
4
4
4
tOW
tSWRD
tSPS
Output Active from End-of-Write(1,2,4)
SEM Flag Write to Read Time
SEM Flag Contention Window
0
5
5
0
5
5
0
5
5
____
____
____
____
____
____
____
____
____
ns
5621 tbl 13
NOTES:
1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2).
2. This parameter is guaranted by device characterization, but is not production tested.
3. To access RAM, CE= VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage
and temperature, the actual tDH will always be smaller than the actual tOW.
5. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 5 for details.
10
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of Read Cycles(5)
tRC
ADDR
(4)
tAA
(4)
tACE
CE(6)
(4)
tAOE
OE
(4)
tABE
UB, LB
R/W
tOH
(1)
tLZ
VALID DATA(4)
DATAOUT
(2)
tHZ
BUSYOUT
(3,4)
5621 drw 06
tBDD
NOTES:
1. Timing depends on which signal is asserted last, OE, CE, LB or UB.
2. Timing depends on which signal is de-asserted first CE, OE, LB or UB.
3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY
has no relation to valid output data.
4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD.
5. SEM = VIH.
Timing of Power-Up Power-Down
CE
tPU
tPD
ICC
SB
50%
50%
.
5621 drw 07
I
11
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8)
tWC
ADDRESS
(7)
tHZ
OE
tAW
CE SEM(9)
or
UB, LB(9)
(3)
(2)
(6)
tWR
tAS
tWP
W
R/
(7)
tOW
tWZ
(4)
(4)
DATAOUT
DATAIN
tDW
tDH
5621 drw 08
Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5)
tWC
ADDRESS
tAW
(9)
or
CE SEM
(6)
tAS
(3)
(2)
tWR
tEW
(9)
,
UB LB
R/
W
tDW
tDH
DATAIN
5621 drw 09
NOTES:
1. R/W or CE or BEn = VIH during all address transitions.
2. A write occurs during the overlap (tEW or tWP) of a CE = VIL and a R/W = VIL for memory array writing cycle.
3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle.
4. During this period, the I/O pins are in the output state and input signals must not be applied.
5. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state.
6. Timing depends on which enable signal is asserted last, CE or R/W.
7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load
(Figure 2).
8. If OE = VIL during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be
placed on the bus for the required tDW. If OE = VIH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the
specified tWP.
9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition.
12
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Semaphore Read after Write Timing, Either Side(1)
tSAA
A0-A2
VALID ADDRESS
VALID ADDRESS
tAW
tWR
tACE
tEW
SEM/UB/LB(1)
tOH
tSOP
tDW
IN
OUT
DATA
VALID(2)
I/O
DATA VALID
tAS
tWP
tDH
R/W
tSWRD
tAOE
OE
tSOP
Write Cycle
Read Cycle
5621 drw 10
NOTES:
1. CE = VIH or UB and LB = VIH for the duration of the above timing (both write and read cycle) (Refer to Chip Enable Truth Table). Refer also to Truth Table II for appropriate
UB/LB controls.
2. "DATAOUT VALID" represents all I/O's (I/O0 - I/O17) equal to the semaphore value.
Timing Waveform of Semaphore Write Contention(1,3,4)
A0"A"-A2"A"
MATCH
(2)
SIDE "A"
R/W"A"
SEM"A"
tSPS
A0"B"-A2"B"
MATCH
(2)
SIDE
R/W"B"
SEM"B"
"B"
5621 drw 11
NOTES:
1. DOR = DOL = VIL, CEL = CER = VIH. Refer also to Truth Table II for appropriate UB/LB controls.
2. All timing is the same for left and right ports. Port "A" may be either left or right port. "B" is the opposite from port "A".
3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH.
4. If tSPS is not satisfied,the semaphore will fall positively to one side or the other, but there is no guarantee which side will be granted the semaphore flag.
13
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange
70V639S10
Com'l Only
70V639S12
Com'l
& Ind
70V639S15
Com'l
& Ind
Symbol
Parameter
Unit
Min.
Max.
Min.
Max.
Min.
Max.
BUSY TIMING (M/S=VIH)
____
____
____
____
____
____
____
____
____
____
____
____
tBAA
tBDA
tBAC
tBDC
tAPS
tBDD
tWH
10
10
10
12
12
12
15
15
15
ns
ns
ns
ns
ns
ns
ns
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
Access Time from Chip Enable Low
BUSY
10
12
15
BUSY Disable Time from Chip Enable High
Arbitration Priority Set-up Time(2)
5
5
5
____
____
____
BUSY Disable to Valid Data(3)
Write Hold After BUSY(5)
____
____
____
10
12
15
____
____
____
8
10
12
BUSY TIMING (M/S=VIL)
BUSY Input to Write(4)
____
____
____
____
____
____
tWB
0
8
0
0
ns
ns
(5)
tWH
Write Hold After
10
12
BUSY
PORT-TO-PORT DELAY TIMING
____
____
____
____
____
____
tWDD
tDDD
Write Pulse to Data Delay(1)
22
20
25
22
30
25
ns
Write Data Valid to Read Data Delay(1)
ns
5621 tbl 14
NOTES:
1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)".
2. To ensure that the earlier of the two ports wins.
3. tBDD is a calculated parameter and is the greater of the Max. spec, tWDD – tWP (actual), or tDDD – tDW (actual).
4. To ensure that the write cycle is inhibited on port "B" during contention on port "A".
5. To ensure that a write cycle is completed on port "B" after contention on port "A".
14
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
TimingWaveformof WritewithPort-to-PortReadandBUSY (M/S = VIH)(2,4,5)
tWC
MATCH
ADDR"A"
R/W"A"
tWP
tDW
tDH
VALID
DATAIN "A"
(1)
tAPS
MATCH
ADDR"B"
tBAA
tBDA
tBDD
BUSY"B"
tWDD
DATAOUT "B"
VALID
(3)
tDDD
.
5621 drw 12
NOTES:
1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (SLAVE).
2. CEL = CER = VIL.
3. OE = VIL for the reading port.
4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above.
5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A".
Timing Waveform of Write with BUSY (M/S = VIL)
tWP
R/W"A"
(3)
tWB
BUSY"B"
(1)
tWH
(2)
R/W"B"
5621 drw 13
NOTES:
1. tWH must be met for both BUSY input (SLAVE) and output (MASTER).
2. BUSY is asserted on port "B" blocking R/W"B", until BUSY"B" goes HIGH.
3. tWB is only for the 'slave' version.
15
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of BUSY Arbitration Controlled by CE Timing(M/S = VIH)(1)
ADDR"A"
ADDRESSES MATCH
and "B"
"A"
CE
(2)
tAPS
CE"B"
tBAC
tBDC
"B"
BUSY
5621 drw 14
Waveform of BUSY Arbitration Cycle Controlled by Address Match
Timing(M/S = VIH)(1)
"A"
"B"
"B"
ADDR
ADDRESS "N"
(2)
tAPS
ADDR
MATCHING ADDRESS "N"
BAA
BDA
t
t
BUSY
5621 drw 15
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted.
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange
70V639S10
Com'l Only
70V639S12
Com'l
& Ind
70V639S15
Com'l
& Ind
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
INTERRUPT TIMING
____
____
____
____
____
____
tAS
Address Set-up Time
0
0
0
ns
ns
ns
tWR
tINS
tINR
Write Recovery Time
Interrupt Set Time
0
0
0
____
____
____
10
10
12
12
15
15
____
____
____
Interrupt Reset Time
ns
5621 tbl 15
16
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of Interrupt Timing(1)
tWC
INTERRUPT SET ADDRESS(2)
ADDR"A"
(4)
(3)
WR
t
tAS
"A"
CE
R/ "A"
W
(3)
INS
t
"B"
INT
5621 drw 16
tRC
INTERRUPT CLEAR ADDRESS (2)
ADDR"B"
(3)
tAS
"B"
CE
"B"
OE
(3)
tINR
"B"
INT
5621 drw 17
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. Refer to Interrupt Truth Table.
3. Timing depends on which enable signal (CE or R/W) is asserted last.
4. Timing depends on which enable signal (CE or R/W) is de-asserted first.
Truth Table III Interrupt Flag(1,4)
Left Port
Right Port
R/
L
A16L-A0L
1FFFF
X
R/
R
A16R-A0R
X
Function
Set Right INTR Flag
W
L
L
L
W
R
CE
OE
INT
CE
OE
R
INTR
(2)
L
X
X
X
L
X
X
L
X
X
X
L
X
X
X
L
X
L
L
X
X
L
L
(3)
X
1FFFF
1FFFE
X
H
Reset Right INTR Flag
Set Left INTL Flag
(3)
X
L
X
X
X
X
(2)
1FFFE
H
X
Reset Left INTL Flag
5621 tbl 16
NOTES:
1. Assumes BUSYL = BUSYR =VIH.
2. If BUSYL = VIL, then no change.
3. If BUSYR = VIL, then no change.
4. INTL and INTR must be initialized at power-up.
17
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table IV
Address BUSY Arbitration
Inputs
Outputs
A
OL-A16L
(1 )
(1 )
A
OR-A16R
Function
No rmal
No rmal
No rmal
CE
L
CE
R
BUSY
L
BUSY
R
X
H
X
L
X
X
H
L
NO MATCH
MATCH
H
H
H
H
MATCH
H
H
MATCH
(2)
(2)
Write Inhib it(3 )
5621 tbl 17
NOTES:
1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT70V639
are push-pull, not open drain outputs. On slaves the BUSY input internally inhibits writes.
2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address
and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously.
3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored
when BUSYR outputs are driving LOW regardless of actual logic level on the pin.
Truth Table V Example of Semaphore Procurement Sequence(1,2,3)
Functions
D0 - D17 Left
D0 - D17 Right
Status
No Action
1
0
0
1
1
0
1
1
1
0
1
1
1
1
0
0
1
1
0
1
1
1
Semaphore free
Left Port Writes "0" to Semaphore
Right Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "1" to Semaphore
Right Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
5621 tbl 18
NOTES:
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT70V639.
2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O17). These eight semaphores are addressed by A0 - A2.
3. CE = VIH, SEM = VIL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table.
FunctionalDescription
The IDT70V639 provides two ports with separate control, address
and I/O pins that permit independent access for reads or writes to any
locationinmemory.TheIDT70V639hasanautomaticpowerdownfeature
controlled by CE. The CE0 and CE1 control the on-chip power down
circuitrythatpermitstherespectiveporttogointoastandbymodewhen
notselected(CE =HIGH).Whenaportis enabled,access totheentire
memoryarrayispermitted.
3FFFE (HEX), where a write is defined as CER = R/WR = VIL per the
Truth Table. The left port clears the interrupt through access of
address location 3FFFE when CEL = OEL = VIL, R/W is a "don't care".
Likewise, the right port interrupt flag (INTR) is asserted when the left
port writes to memory location 3FFFF (HEX) and to clear the interrupt
flag (INTR), the right port must read the memory location 3FFFF. The
message (18 bits) at 3FFFE or 3FFFF is user-defined since it is an
addressable SRAM location. If the interrupt function is not used,
address locations 3FFFE and 3FFFF are not used as mail boxes, but
as part of the random access memory. Refer to Truth Table III for
theinterruptoperation.
Interrupts
If the user chooses the interrupt function, a memory location (mail
boxormessagecenter)isassignedtoeachport. Theleftportinterrupt
flag (INTL) is asserted when the right port writes to memory location
18
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
address signals only. It ignores whether an access is a read or write.
In a master/slave array, both address and chip enable must be valid
long enough for a BUSY flag to be output from the master before the
actual write pulse can be initiated with the R/W signal. Failure to
observe this timing can result in a glitched internal write inhibit signal
andcorrupteddata inthe slave.
BusyLogic
BusyLogicprovidesahardwareindicationthatbothportsoftheRAM
haveaccessedthesamelocationatthesametime.Italsoallowsoneofthe
twoaccessestoproceedandsignalstheothersidethattheRAMis“Busy”.
TheBUSYpincanthenbeusedtostalltheaccessuntiltheoperationon
theothersideiscompleted.Ifawriteoperationhasbeenattemptedfrom
thesidethatreceivesaBUSYindication,thewritesignalisgatedinternally
topreventthewritefromproceeding.
Semaphores
TheuseofBUSYlogicisnotrequiredordesirableforallapplications.
InsomecasesitmaybeusefultologicallyORtheBUSYoutputstogether
anduse anyBUSY indicationas aninterruptsource toflagthe eventof
anillegalorillogicaloperation.IfthewriteinhibitfunctionofBUSYlogicis
notdesirable,theBUSYlogiccanbedisabledbyplacingthepartinslave
modewiththeM/Spin.OnceinslavemodetheBUSYpinoperatessolely
asawriteinhibitinputpin.Normaloperationcanbeprogrammedbytying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
The BUSY outputs on the IDT70V639 RAM in master mode, are
push-pull type outputs and do not require pull up resistors to operate.
Ifthese RAMs are beingexpandedindepth, thentheBUSY indication
for the resulting array requires the use of an external AND gate.
The IDT70V639 is an extremely fast Dual-Port 128K x 18 CMOS
Static RAM with an additional 8 address locations dedicated to binary
semaphore flags. These flags alloweitherprocessoronthe leftorright
side ofthe Dual-PortRAMtoclaima privilege overthe otherprocessor
for functions defined by the system designer’s software. As an ex-
ample, the semaphore can be used by one processor to inhibit the
other from accessing a portion of the Dual-Port RAM or any other
sharedresource.
The Dual-Port RAM features a fast access time, with both ports
being completely independent of each other. This means that the
activityontheleftportinnowayslows theaccess timeoftherightport.
Both ports are identical in function to standard CMOS Static RAM and
can be read from or written to at the same time with the only possible
conflict arising from the simultaneous writing of, or a simultaneous
READ/WRITE of, a non-semaphore location. Semaphores are pro-
tected against such ambiguous situations and may be used by the
system program to avoid any conflicts in the non-semaphore portion
of the Dual-Port RAM. These devices have an automatic power-down
feature controlled by CE, the Dual-Port RAM enable, and SEM, the
semaphore enable. The CE and SEM pins control on-chip power
downcircuitrythatpermits the respective porttogointostandbymode
whennotselected.
A17
CE0
CE0
MASTER
Dual Port RAM
SLAVE
Dual Port RAM
BUSY
BUSY
R
R
BUSY
BUSY
L
L
CE1
CE1
R
MASTER
SLAVE
Dual Port RAM
Dual Port RAM
Systems which can best use the IDT70V639 contain multiple
processors or controllers and are typically very high-speed systems
which are software controlled or software intensive. These systems
can benefit from a performance increase offered by the IDT70V639s
hardware semaphores, which provide a lockout mechanism without
requiringcomplexprogramming.
BUSY
BUSY
L
L
BUSY
BUSY
R
.
5621 drw 18
Figure 3. Busy and chip enable routing for both width and depth
expansion with IDT70V639 RAMs.
Softwarehandshakingbetweenprocessors offers themaximumin
system flexibility by permitting shared resources to be allocated in
varying configurations. The IDT70V639 does not use its semaphore
flags to control any resources through hardware, thus allowing the
systemdesignertotalflexibilityinsystemarchitecture.
An advantage of using semaphores rather than the more common
methods of hardware arbitration is that wait states are never incurred
in either processor. This can prove to be a major advantage in very
high-speedsystems.
Width Expansion with Busy Logic
Master/SlaveArrays
When expanding an IDT70V639 RAM array in width while using
BUSYlogic, one master part is used to decide which side of the RAMs
array will receive aBUSY indication, and to output that indication. Any
number of slaves to be addressed in the same address range as the
master use the BUSY signal as a write inhibit signal. Thus on the
IDT70V639 RAM the BUSY pin is an output if the part is used as a
master (M/S pin = VIH), and the BUSY pin is an input if the part used
as a slave (M/S pin = VIL) as shown in Figure 3.
If two or more master parts were used when expanding in width, a
splitdecisioncouldresultwithonemasterindicatingBUSYononeside
of the array and another master indicating BUSY on one other side of
the array. This would inhibit the write operations from one port for part
of a word and inhibit the write operations from the other port for the
other part of the word.
How the Semaphore Flags Work
The semaphore logic is a set of eight latches which are indepen-
dent of the Dual-Port RAM. These latches can be used to pass a flag,
or token, from one port to the other to indicate that a shared resource
is in use. The semaphores provide a hardware assist for a use
assignmentmethodcalled“TokenPassingAllocation.”Inthis method,
the state of a semaphore latch is used as a token indicating that a
shared resource is in use. If the left processor wants to use this
resource,itrequeststhetokenbysettingthelatch.Thisprocessorthen
The BUSY arbitration on a master is based on the chip enable and
19
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
question. Meanwhile, if a processor on the right side attempts to write
a zero to the same semaphore flag it will fail, as will be verified by the
fact that a one will be read from that semaphore on the right side
during subsequent read. Had a sequence of READ/WRITE been
usedinstead,systemcontentionproblemscouldhaveoccurredduring
the gap between the read and write cycles.
It is important to note that a failed semaphore request must be
followed by either repeated reads or by writing a one into the same
location. The reason for this is easily understood by looking at the
simple logic diagram of the semaphore flag in Figure 4. Two sema-
phore request latches feed into a semaphore flag. Whichever latch is
first to present a zero to the semaphore flag will force its side of the
semaphore flag LOW and the other side HIGH. This condition will
verifiesitssuccessinsettingthelatchbyreadingit. Ifitwassuccessful,it
proceeds to assume control over the shared resource. If it was not
successfulinsettingthelatch,itdeterminesthattherightsideprocessor
has set the latch first, has the token and is using the shared resource.
The left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore to
perform another task and occasionally attempt again to gain control of
the token via the set and test sequence. Once the right side has
relinquishedthetoken,theleftsideshouldsucceedingainingcontrol.
The semaphore flags are active LOW. A token is requested by
writing a zero into a semaphore latch and is released when the same
sidewritesaonetothatlatch.
The eight semaphore flags reside within the IDT70V639 in a
separate memoryspace fromthe Dual-PortRAM. This address space
is accessedbyplacingalowinputonthe SEM pin(whichacts as achip
select for the semaphore flags) and using the other control pins
(Address, CE, R/W and LB/UB) as they would be used in accessing a
standard Static RAM. Each of the flags has a unique address which
can be accessed by either side through address pins A0 – A2. When
accessing the semaphores, none of the other address pins has
anyeffect.
L PORT
R PORT
SEMAPHORE
REQUEST FLIP FLOP
SEMAPHORE
REQUEST FLIP FLOP
0
D
0
D
D
D
Q
Q
WRITE
WRITE
Whenwritingtoasemaphore,onlydatapinD0 isused.Ifalowlevel
is written into an unused semaphore location, that flag will be set to
a zero on that side and a one on the other side (see Truth Table V).
Thatsemaphorecannowonlybemodifiedbythesideshowingthezero.
When a one is written into the same location from the same side, the
SEMAPHORE
READ
SEMAPHORE
READ
5621 drw 19
Figure 4. IDT70V639 Semaphore Logic
flag will be set to a one for both sides (unless a semaphore request continue until a one is written to the same semaphore request latch.
fromtheothersideispending)andthencanbewrittentobybothsides. Should the other side’s semaphore request latch have been written to
The fact that the side which is able to write a zero into a semaphore a zero in the meantime, the semaphore flag will flip over to the other
subsequently locks out writes from the other side is what makes side as soon as a one is written into the first side’s request latch. The
semaphore flags useful in interprocessor communications. (A thor- secondside’s flagwillnowstay LOWuntilits semaphore requestlatch
ough discussion on the use of this feature follows shortly.) A zero is written to a one. From this it is easy to understand that, if a
written into the same location from the other side will be stored in the semaphore is requested and the processor which requested it no
semaphore request latch for that side until the semaphore is freed by longer needs the resource, the entire system can hang up until a one
thefirstside.
Whena semaphore flagis read, its value is spreadintoalldata bits
iswrittenintothatsemaphorerequestlatch.
The critical case of semaphore timing is when both sides request
so that a flag that is a one reads as a one in all data bits and a flag a single tokenbyattemptingtowrite a zerointoitatthe same time. The
containinga zeroreads as allzeros. The readvalue is latchedintoone semaphore logic is specially designed to resolve this problem. If
side’s output register when that side's semaphore, byte select (SEM, simultaneous requests are made, the logic guarantees that only one
LB/UB)andoutputenable(OE)signalsgoactive.Thisservestodisallow side receives the token. If one side is earlier than the other in making
thesemaphorefromchangingstateinthemiddleofareadcycleduetoa the request, the first side to make the request will receive the token. If
write cycle from the other side. Because of this latch, a repeated read bothrequests arriveatthesametime,theassignmentwillbearbitrarily
of a semaphore in a test loop must cause either signal (SEM or OE) to made to one port or the other.
go inactive or the output will never change. However, during reads LB
andUBfunctiononlyasanoutputforsemaphore.Theydonothaveany semaphores alone do not guarantee that access to a resource is
influenceonthesemaphorecontrollogic. secure. As with any powerful programming technique, if semaphores
A sequence WRITE/READ must be used by the semaphore in are misusedormisinterpreted, a software errorcaneasilyhappen.
order to guarantee that no system level contention will occur. A Initialization of the semaphores is not automatic and must be
One caution that should be noted when using semaphores is that
processor requests access to shared resources by attempting to write handled via the initialization program at power-up. Since any sema-
a zero into a semaphore location. If the semaphore is already in use, phore request flag which contains a zero must be reset to a one,
the semaphore request latch will contain a zero, yet the semaphore all semaphores on both sides should have a one written into them
flag will appear as one, a fact which the processor will verify by the at initialization from both sides to assure that they will be free
subsequent read (see Table V). As an example, assume a processor when needed.
writes a zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written success-
fully to that location and will assume control over the resource in
20
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
JTAGTimingSpecifications
t
JCYC
t
JR
t
JF
t
JCL
t
JCH
TCK
Device Inputs(1)/
TDI/TMS
tJDC
t
JS
t
JH
Device Outputs(2)/
TDO
t
JRSR
tJCD
TRST
x
5621 drw 20
t
JRST
NOTES:
1. Device inputs = All device inputs except TDI, TMS, and TRST.
2. Device outputs = All device outputs except TDO.
JTAG AC Electrical
Characteristics(1,2,3,4)
Symbol
tJCYC
tJCH
Parameter
JTAG Clock Input Period
JTAG Clock HIGH
JTAG Clock Low
JTAG Clock Rise Time
JTAG Clock Fall Time
JTAG Reset
Min.
100
40
Max.
Units
ns
____
____
____
ns
tJCL
40
ns
(1)
____
tJR
3
ns
(1)
____
tJF
3
ns
____
____
JRST
t
50
ns
tJRSR
tJCD
tJDC
tJS
JTAG Reset Recovery
JTAG Data Output
JTAG Data Output Hold
JTAG Setup
50
ns
____
25
ns
____
0
ns
____
____
15
15
ns
JH
t
JTAG Hold
ns
5621 tbl 19
NOTES:
1. Guaranteed by design.
2. 30pF loading on external output signals.
3. Refer to AC Electrical Test Conditions stated earlier in this document.
4. JTAG operations occur at one speed (10MHz). The base device may run at
any speed specified in this datasheet.
21
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Identification Register Definitions
Instruction Field
Value
Description
Revision Number (31:28)
0x0
Reserved for version number
IDT Device ID (27:12)
0x30C
0x33
1
Defines IDT part number
IDT JEDEC ID (11:1)
Allows unique identification of device vendor as IDT
Indicates the presence of an ID register
ID Register Indicator Bit (Bit 0)
5621 tbl 20
ScanRegisterSizes
Register Name
Bit Size
Instruction (IR)
4
1
Bypass (BYR)
Identification (IDR)
32
Boundary Scan (BSR)
Note (3)
5621 tbl 21
SystemInterfaceParameters
Instruction
Code
Description
EXTEST
0000
Forces contents of the boundary scan cells onto the device outputs(1) .
Places the boundary scan register (BSR) between TDI and TDO.
BYPASS
IDCODE
1111
Places the by pass registe r (BYR) between TDI and TDO.
0010
Loads the ID register (IDR) with the vendor ID code and places the
register between TDI and TDO.
0100
Places the bypass register (BYR) between TDI and TDO. Forces all
device output drivers to a High-Z state.
HIGHZ
CLAMP
Uses BYR. Forces contents of the boundary scan cells onto the device
outputs. Places the bypass register (BYR) between TDI and TDO.
0011
0001
SAMPLE/PRELOAD
Places the boundary scan register (BSR) between TDI and TDO.
SAMPLE allows data from device inputs(2) and outputs(1) to be captured
in the boundary scan cells and shifted serially through TDO. PRELOAD
allows data to be input serially into the boundary scan cells via the TDI.
RESERVED
All other codes
Several combinations are reserved. Do notuse codes other than those
identified above.
5621 tbl 22
NOTES:
1. Device outputs = All device outputs except TDO.
2. Device inputs = All device inputs except TDI, TMS, and TRST.
3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local
IDT sales representative.
22
IDT70V639S
Preliminary
High-Speed 3.3V 128K x 18 Asynchronous Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Ordering Information
IDT XXXXX
A
999
A
A
Device
Type
Power
Speed
Package
Process/
Temperature
Range
Blank
I
Commercial (0 C to +70 C)
°
°
Industrial (-40 C to +85 C)
°
°
BF
PRF
BC
208-ball fpBGA (BF-208)
128-pin TQFP (PK-128)
256-ball BGA (BC-256)
10
12
15
Commercial Only
Commercial & Industrial
Commercial & Industrial
Speed in nanoseconds
S
Standard Power
70V639 2304K (128K x 18) Asynchronous Dual-Port RAM
5621 drw 21
PreliminaryDatasheet:Definition
"PRELIMINARY'datasheetscontaindescriptionsforproductsthatareinearlyrelease.
DatasheetDocumentHistory:
6/1/00:
8/7/00:
6/20/01:
InitialPublicOffering.
Pages6,13,20InsertedadditionalLBandUBinformation.
AddedJTAGinformationforTQFPpackage onpage 1.
Increased BUSY TIMINGparameters tBDA,tBAC,tBDC andtBDD forallspeeds onpage14.
Changed maximumvalueforJTAGACElectricalCharacteristics fortJCD from20ns to25ns onpage21.
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
for Tech Support:
831-754-4613
DualPortHelp@idt.com
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
23
相关型号:
IDT70V639S15PRFGI
Dual-Port SRAM, 128KX18, 15ns, CMOS, PQFP128, 14 X 20 MM, 1.40 MM HEIGHT, GREEN, TQFP-128
IDT
IDT70V657S10BCG
Dual-Port SRAM, 32KX36, 10ns, CMOS, PBGA256, 17 X 17 MM, 1.40 MM HEIGHT, 1 MM PITCH, GREEN, BGA-256
IDT
IDT70V657S10BCG8
Dual-Port SRAM, 32KX36, 10ns, CMOS, PBGA256, 17 X 17 MM, 1.40 MM HEIGHT, 1 MM PITCH, BGA-256
IDT
IDT70V657S10BF8
Dual-Port SRAM, 32KX36, 10ns, CMOS, PBGA208, 15 X 15 MM, 1.40 MM HEIGHT, 0.80 MM PITCH, FPBGA-208
IDT
©2020 ICPDF网 联系我们和版权申明