IDT723654L12PFG [IDT]
FIFO, 2KX36, 8ns, Synchronous, CMOS, PQFP128, TQFP-128;型号: | IDT723654L12PFG |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | FIFO, 2KX36, 8ns, Synchronous, CMOS, PQFP128, TQFP-128 先进先出芯片 |
文件: | 总37页 (文件大小:414K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CMOS SyncBiFIFOTM WITH BUS-MATCHING
2,048 x 36 x 2
4,096 x 36 x 2
IDT723654
IDT723664
IDT723674
8,192 x 36 x 2
• Port B bus sizing of 36 bits (long word), 18 bits (word) and 9 bits
(byte)
• Big- or Little-Endian format for word and byte bus sizes
• Retransmit Capability
• Master Reset clears data and configures FIFO, Partial Reset
clears data but retains configuration settings
• Mailbox bypass registers for each FIFO
• Free-running CLKA and CLKB may be asynchronous or coincident
(simultaneous reading and writing of data on a single clock edge
is permitted)
• Auto power down minimizes power dissipation
• Available in space saving 128-pin Thin Quad Flatpack (TQFP)
• Pincompatibletothelowerdensityparts, IDT723624/723634/723644
• Industrial temperature range (–40°C to +85°C) is available
FEATURES
• Memory storage capacity:
IDT723654
IDT723664
IDT723674
–
–
–
2,048 x 36 x 2
4,096 x 36 x 2
8,192 x 36 x 2
• Clock frequencies up to 83 MHz (8ns access time)
• Two independent clocked FIFOs buffering data in opposite
directions
• Select IDT Standard timing (using EFA, EFB, FFA, and FFB flags
functions) or First Word Fall Through Timing (using ORA, ORB,
IRA, and IRB flag functions)
• Programmable Almost-Empty and Almost-Full flags; each has five
default offsets (8, 16, 64, 256 and 1,024 )
• Serial or parallel programming of partial flags
FUNCTIONAL BLOCK DIAGRAM
MBF1
Mail 1
Register
CLKA
Port-A
Control
Logic
CSA
W/RA
ENA
RAM ARRAY
2,048 x 36
4,096 x 36
8,192 x 36
36
36
MBA
36
FIFO1,
Mail1
Reset
Logic
MRS1
PRS1
Write
Pointer
Read
Pointer
36
Status Flag
Logic
EFB/ORB
AEB
FFA/IRA
AFA
FIFO1
FIFO2
FS2
FS0/SD
Programmable Flag
Offset Registers
Timing
Mode
FWFT
FS1/SEN
B0-B35
A0-A35
13
Status Flag
Logic
EFA/ORA
FFB/IRB
AFB
AEA
36
Read
Pointer
Write
Pointer
36
FIFO2,
Mail2
Reset
Logic
MRS2
PRS2
RT1
RTM
RT2
FIFO1 and
FIFO2
Retransmit
Logic
RAM ARRAY
2,048 x 36
4,096 x 36
8,192 x 36
36
36
CLKB
CSB
W/RB
ENB
MBB
BE
Port-B
Control
Logic
Mail 2
Register
BM
SIZE
MBF2
5608 drw01
IDTandtheIDTlogoaretrademarksofIntegratedDeviceTechnology,Inc.SyncBiFIFOisatrademarkofIntegratedDeviceTechnology,Inc.
NOVEMBER 2003
COMMERCIAL TEMPERATURE RANGE
1
2003 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.
DSC-5608/6
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
These devices are a synchronous (clocked) FIFO, meaning each port
DESCRIPTION
employsasynchronousinterface. Alldatatransfersthroughaportaregated
totheLOW-to-HIGHtransitionofaportclockbyenablesignals. Theclocksfor
each port are independent of one another and can be asynchronous or
coincident. The enables for each port are arranged to provide a simple
bidirectionalinterfacebetweenmicroprocessorsand/orbuseswithsynchro-
nouscontrol.
TheIDT723654/723664/723674isamonolithic,high-speed,low-power,
CMOS bidirectional synchronous (clocked) FIFO memory which supports
clockfrequenciesupto83MHzandhasreadaccesstimesasfastas8ns. Two
independent2,048/4,096/8,192 x 36dual-portSRAMFIFOsonboardeach
chipbufferdatainoppositedirections. FIFOdataonPortBcanbeinputand
outputin36-bit, 18-bit, or9-bitformats witha choice ofBig-orLittle-Endian
configurations.
PIN CONFIGURATION
INDEX
W/RA
ENA
CLKA
3
GND
A35
5
A34
A33
7
A32
Vcc
A31
A30
GND
A29
A28
A27
A26
A25
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
CLKB
PRS2/RT2
Vcc
1
2
B35
B34
B33
B32
RTM
GND
B31
B30
B29
B28
B27
B26
Vcc
4
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
B25
B24
BM
A24
A23
BE/FWFT
GND
A22
GND
B23
B22
B21
B20
B19
B18
GND
B17
B16
SIZE
Vcc
B15
B14
B13
B12
GND
B11
B10
Vcc
A21
A20
A19
A18
GND
A17
A16
A15
A14
A13
Vcc
A12
GND
A11
A10
5608 drw02
TQFP (PK128-1, order code: PF)
TOP VIEW
2
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CommunicationbetweeneachportmaybypasstheFIFOsviatwomailbox necessitateaformalreadrequest).ThestateoftheBE/FWFTpinduringFIFO
registers.Themailboxregisters’widthmatchestheselectedPortBbuswidth. operationdeterminesthemodeinuse.
EachMailboxregisterhas a flag(MBF1 andMBF2)tosignalwhennewmail
has beenstored.
EachFIFOhasacombinedEmpty/OutputReadyFlag(EFA/ORAandEFB/
ORB) and a combined Full/Input Ready Flag (FFA/IRA and FFB/IRB). The
TwokindsofresetareavailableontheseFIFOs:MasterResetandPartial EF and FF functions are selected in the IDT Standard mode. EF indicates
Reset. MasterResetinitializesthereadandwritepointerstothefirstlocation whetherornottheFIFOmemoryisempty.FFshowswhetherthememoryis
of the memory array, configures the FIFO for Big- or Little-Endian byte fullornot.TheIRandORfunctionsareselectedintheFirstWordFallThrough
arrangementandselectsserialflagprogramming,parallelflagprogramming, mode.IRindicateswhetherornottheFIFOhasavailablememorylocations.
oroneoffivepossibledefaultflagoffsetsettings,8,16,64,256or1,024.There ORshowswhethertheFIFOhasdataavailableforreadingornot.Itmarksthe
are two Master Reset pins, MRS1 and MRS2.
PartialResetalsosetsthereadandwritepointerstothefirstlocationofthe
presenceofvaliddataontheoutputs.
EachFIFOhasaprogrammableAlmost-Emptyflag(AEAandAEB)anda
memory.UnlikeMasterReset,anysettingsexistingpriortoPartialReset(i.e., programmableAlmost-Fullflag(AFAandAFB). AEAandAEB indicatewhen
programmingmethodandpartialflagdefaultoffsets)areretained.PartialReset aselectednumberofwordsremainintheFIFOmemory.AFAandAFBindicate
is useful since it permits flushing of the FIFO memory without changing any whenthe FIFOcontains more thana selectednumberofwords.
configurationsettings.EachFIFOhasitsown,independentPartialResetpin,
PRS1 and PRS2.
FFA/IRA,FFB/IRB,AFAandAFB aretwo-stagesynchronizedtotheport
clockthatwrites dataintoits array.EFA/ORA,EFB/ORB,AEAandAEBare
BothFIFO'shaveRetransmitcapability,whenaRetransmitisperformedon two-stage synchronized to the port clock that reads data from its array.
arespectiveFIFOonlythereadpointerisresettothefirstmemorylocation.A ProgrammableoffsetsforAEA,AEB,AFAandAFBareloaded inparallelusing
RetransmitisperformedbyusingtheRetransmitMode,RTMpininconjunction PortAorinserialviatheSDinput.Fivedefaultoffsetsettingsarealsoprovided.
withtheRetransmitpinsRT1orRT2,foreachrespectiveFIFO.Notethatthe The AEA and AEB threshold can be set at 8, 16, 64, 256 or 1,024 locations
twoRetransmitpins RT1andRT2 are muxedwiththe PartialResetpins.
fromtheemptyboundaryandtheAFAandAFBthresholdcanbesetat8,16,
Thesedeviceshavetwomodesofoperation:IntheIDTStandardmode,the 64,256or1,024locationsfromthefullboundary.Allthesechoicesaremade
firstwordwrittentoanemptyFIFOisdepositedintothememoryarray. Aread using the FS0, FS1 and FS2 inputs during Master Reset.
operationisrequiredtoaccessthatword(alongwithallotherwordsresiding
InterspersedParitycanalsobeselectedduringaMasterResetoftheFIFO.
inmemory). IntheFirstWordFallThroughmode(FWFT),thefirstwordwritten IfInterspersedParityisselectedthenduringparallelprogrammingoftheflag
to an empty FIFO appears automatically on the outputs, no read operation offsetvalues,thedevicewillignoredatalineA8.IfNon-InterspersedParityis
required (Nevertheless, accessing subsequent words does necessitate a selectedthendatalineA8willbecomeavalidbit.
formal read request). The state of the BE/FWFT pin during Master Reset
determinesthemodeinuse.
Twoormoredevicesmaybeusedinparalleltocreatewiderdatapaths.If,
at any time, the FIFO is not actively performing a function, the chip will
Thesedeviceshavetwomodesofoperation:IntheIDTStandardmode,the automatically power down. During the power down state, supply current
firstwordwrittentoanemptyFIFOisdepositedintothememoryarray.Aread consumption(ICC)isataminimum.Initiatinganyoperation(byactivatingcontrol
operationisrequiredtoaccessthatword(alongwithallotherwordsresiding inputs)willimmediatelytakethedeviceoutofthepowerdownstate.
inmemory).IntheFirstWordFallThroughmode(FWFT),thefirstlong-word
(36-bitwide)writtentoanemptyFIFOappearsautomaticallyontheoutputs,no to70°C.Industrialtemperaturerange(-40°Cto+85°C)isavailable.Theyare
readoperationisrequired(Nevertheless,accessingsubsequentwordsdoes fabricatedusingIDT’shighspeed,submicronCMOStechnology.
TheIDT723654/723664/723674arecharacterizedforoperationfrom0°C
3
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS
Symbol
A0-A35
AEA
Name
I/O
I/O
O
Description
PortAData
36-bitbidirectionaldataportforsideA.
PortAAlmost-
EmptyFlag
ProgrammableAlmost-EmptyflagsynchronizedtoCLKA.ItisLOWwhenthenumberofwordsin
FIFO2islessthanorequaltothevalueintheAlmost-EmptyAOffsetregister,X2.
AEB
PortBAlmost-
EmptyFlag
O
O
O
ProgrammableAlmost-EmptyflagsynchronizedtoCLKB.ItisLOWwhenthenumberofwordsin
FIFO1islessthanorequaltothevalueintheAlmost-EmptyBOffsetregister,X1.
AFA
PortAAlmost-
Full Flag
ProgrammableAlmost-FullflagsynchronizedtoCLKA.ItisLOWwhenthenumberofempty
locationsinFIFO1islessthanorequaltothevalueintheAlmost-FullAOffsetregister,Y1.
AFB
PortBAlmost-
Full Flag
ProgrammableAlmost-FullflagsynchronizedtoCLKB.ItisLOWwhenthenumberofempty
locations inFIFO2is less thanorequaltothevalueintheAlmost-FullBOffsetregister,Y2.
B0-B35
PortAData
I/O
I
36-bitbidirectionaldataportforsideB.
BE/FWFT Big-Endian/
FirstWord
This is a dual purpose pin. During Master Reset, a HIGH on BE will select Big Endian operation.
Inthis case, dependingonthe bus size, the mostsignificantbyte orwordonPortAis readfrom
PortBfirst (A-to-Bdata flow)orwrittentoPortBfirst(B-to-Adata flow). ALOWonBEwillselect
Little-Endianoperation. Inthis case,theleastsignificantbyteorwordonPortAis readfromPortB
first(forA-to-Bdataflow)orwrittentoPortBfirst(B-to-Adata flow). After Master Reset, this pin
selects the timing mode. A HIGH on FWFT selects IDT Standard mode, a LOW selects First Word
FallThroughmode.Oncethetimingmodehas beenselected,thelevelonFWFTmustbestatic
throughoutdeviceoperation.
Fall Through
Select
(1)
BM
Bus-MatchSelect
(Port B)
I
I
I
A HIGH on this pin enables either byte or word bus width on Port B, depending on the state of
SIZE. A LOW selects long word operation. BM works with SIZE and BE to select the bus size and
endianarrangementforPortB.ThelevelofBMmustbestaticthroughoutdeviceoperation.
CLKA
CLKB
PortAClock
PortBClock
CLKAis acontinuous clockthatsynchronizes alldatatransfers throughPortAandcanbe
asynchronous or coincident to CLKB. FFA/IRA, EFA/ORA, AFA, and AEA are allsynchronized
totheLOW-to-HIGHtransitionofCLKA.
CLKBis acontinuous clockthatsynchronizes alldatatransfers throughPortBandcanbe
asynchronous orcoincidenttoCLKA. FFB/IRB, EFB/ORB, AFB, andAEB are synchronizedto
theLOW-to-HIGHtransitionofCLKB.
CSA
CSB
PortAChipSelect
PortBChipSelect
I
I
CSA mustbeLOWtoenabletoLOW-to-HIGHtransitionofCLKAtoreadorwriteonPortA.
The A0-A35outputs are inthe high-impedance state when CSAis HIGH.
CSB mustbe LOWtoenable a LOW-to-HIGHtransitionofCLKBtoreadorwrite data onPortB.
The B0-B35outputs are inthe high-impedance state when CSBis HIGH.
EFA/ORA PortAEmpty/
OutputReadyFlag
O
This is a dualfunctionpin. Inthe IDTStandardmode, the EFA functionis selected. EFA
indicates whetherornotthe FIFO2memoryis empty. Inthe FWFTmode, the ORAfunctionis
selected. ORAindicates thepresenceofvaliddataonA0-A35outputs,availableforreading.
EFA/ORAissynchronizedtotheLOW-to-HIGHtransitionofCLKA.
EFB/ORB PortBEmpty/
OutputReadyFlag
O
This is adualfunctionpin.IntheIDTStandardmode,theEFBfunctionis selected. EFBindicates
whetherornotthe FIFO1memoryis empty. Inthe FWFTmode, the ORBfunctionis selected. ORB
indicates thepresenceofvaliddataontheB0-B35outputs,availableforreading. EFB/ORBis
synchronizedtotheLOW-to-HIGHtransitionofCLKB.
ENA
PortAEnable
I
I
ENAmustbe HIGHtoenable a LOW-to-HIGHtransitionofCLKAtoreadorwrite data onPortA.
ENBmustbe HIGHtoenable a LOW-to-HIGHtransitionofCLKBtoreadorwrite data onPortB.
ENB
PortBEnable
FFA/IRA
PortAFull/
Input Ready Flag
O
This is a dualfunctionpin. Inthe IDTStandardmode, the FFA functionis selected. FFA indicates
whetherornotthe FIFO1memoryis full. Inthe FWFTmode, the IRAfunctionis selected. IRA
indicates whetherornotthere is space available forwritingtothe FIFO1memory. FFA/IRAis
synchronizedtotheLOW-to-HIGHtransitionofCLKA.
FFB/IRB
PortBFull/
Input Ready Flag
O
This is adualfunctionpin.IntheIDTStandardmode,the FFB functionis selected. FFB indicates
whether or not the FIFO2 memory is full. In the FWFT mode, the IRB function is selected. IRB
indicates whether or not there is space available for writing to the FIFO2 memory. FFB/IRB is
synchronized to the LOW-to-HIGH transition of CLKB.
4
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS(CONTINUED)
Symbol
Name
I/O
Description
FS0/SD
FlagOffsetSelect0/
SerialData
I
FS1/SEN andFS0/SDaredual-purposeinputs usedforflagoffsetregisterprogramming. During
MasterReset,FS1/SENandFS0/SD,togetherwithFS2,selecttheflagoffsetprogrammingmethod.
Threeoffsetregisterprogrammingmethodsareavailable:automaticallyloadoneoffivepreset
values (8, 16, 64, 256 or 1,024), parallel load from Port A, and serial load.
FS1/SEN
FlagOffsetSelect1/
SerialEnable
Whenserialloadisselectedforflagoffsetregisterprogramming,FS1/SENisusedasanenable
synchronous totheLOW-to-HIGHtransitionofCLKA. WhenFS1/SENis LOW,arisingedgeon
CLKA load the bit present on FS0/SD into the X and Y registers. The number of bit writes required
to program the offset registers is 44 for the IDT723654, 48 for the IDT723664, and 52 for the
IDT723674.Thefirstbitwritestores theY-register(Y1)MSBandthelastbitwritestores the
X-register (X2) LSB.
FS2(1)
FlagOffsetSelect2
I
I
MBA
MBB
MBF1
Port A Mailbox
Select
A HIGH level on MBA chooses a mailbox register for a Port A read or write operation. When
theA0-A35outputsareactive,aHIGHlevelonMBAselectsdatafromthemail2registerforoutput
andaLOWlevelselectsFIFO2outputregisterdataforoutput.
Port B Mailbox
Select
I
A HIGH level on MBB chooses a mailbox register for a Port B read or write operation. When the
B0-B35outputs areactive,aHIGHlevelonMBBselects datafromthemail1registerforoutputand
aLOWlevelselectsFIFO1outputregisterdataforoutput.
Mail1Register
Flag
O
MBF1 is set LOW by a LOW-to-HIGH transition of CLKA that writes data to the mail1 register.
Writes tothe mail1registerare inhibitedwhile MBF1 is LOW. MBF1 is setHIGHbya LOW-to-
HIGH transition of CLKB when a Port B read is selected and MBB is HIGH. MBF1 is set HIGH
followingeitheraMasterorPartialResetofFIFO1.
MBF2
MRS1
Mail2Register
Flag
O
I
MBF2issetLOWbyaLOW-to-HIGHtransitionofCLKBthatwritesdatatothemail2register.
Writes tothemail2registerareinhibitedwhileMBF2 is LOW.MBF2 is setHIGHbyaLOW-to-HIGH
transition of CLKA when a Port A read is selected and MBA is HIGH. MBF2 is set HIGH
followingeitheraMasterorPartialResetofFIFO2.
FIFO1Master
Reset
ALOWonthis pin initializes the FIFO1readandwrite pointers tothe firstlocationofmemoryand
setsthePortBoutputregistertoallzeroes. ALOW-to-HIGHtransitiononMRS1selectstheprogramming
method(serialorparallel)andoneoffiveprogrammableflagdefaultoffsets forFIFO1andFIFO2.It
also configuresPortBforbussizeandendianarrangement. FourLOW-to-HIGHtransitionsofCLKA
andfourLOW-to-HIGHtransitionsofCLKBmustoccurwhileMRS1isLOW.
MRS2
FIFO2Master
Reset
I
I
ALOWonthispininitializestheFIFO2readandwritepointerstothefirstlocationofmemoryandsets
thePortAoutputregistertoallzeroes.ALOW-to-HIGHtransitiononMRS2,toggledsimultaneously
withMRS1,selectstheprogrammingmethod(serialorparallel)andoneoftheprogrammableflagdefault
offsets for FIFO2. Four LOW-to-HIGH transitions of CLKA and four LOW-to-HIGH transitions of CLKB
mustoccurwhileMRS2isLOW.
PRS1/
RT1
PartialReset/
RetransmitFIFO1
ThispinismuxedforbothPartialReset andRetransmitoperations,itisusedinconjunctionwiththeRTM
pin. IfRTMisinaLOWcondition,aLOWonthispinperformsaPartialResetonFIFO1andinitializes
theFIFO1readandwritepointerstothefirstlocationofmemoryandsetsthePortBoutputregisterto
allzeroes.DuringPartialReset,thecurrentlyselectedbussize,endianarrangement,programming
method(serialorparallel),andprogrammableflagsettingsareallretained.IfRTMisHIGH,aLOWon
thispinperformsaRetransmitandinitializestheFIFO1readpointeronlytothefirstmemorylocation.
PRS2/
RT2
PartialReset/
RetransmitFIFO2
I
ThispinismuxedforbothPartialReset andRetransmitoperations,itisusedinconjunctionwiththeRTM
pin. IfRTMisinaLOWcondition,aLOWonthispinperformsaPartialResetonFIFO2andinitializes
theFIFO2readandwriteselectedbus size,endianarrangement,programmingmethod(serialor
parallel),andprogrammableflagsettingsareallretained.IfRTMisHIGH,aLOWonthispinperforms
aRetransmitandinitializestheFIFO2readpointeronlytothefirstmemorylocation.
RTM
RetransmitMode
BusSizeSelect
I
I
ThispinisusedinconjunctionwiththeRT1andRT2pins.WhenRTMisHIGHaRetransmitisperformed
on FIFO1 or FIFO2 respectively.
(1)
SIZE
AHIGHonthis pinwhenBMis HIGHselects byte bus (9-bit)size onPortB. ALOWonthis pinwhen
BMisHIGHselectsword(18-bit)bussize.SIZEworkswithBMandBEtoselectthebussizeandendian
arrangementforPortB.ThelevelofSIZEmustbestaticthroughoutdeviceoperation
NOTE:
1. FS2, BM and SIZE inputs are not TTL compatible. These inputs should be tied to GND or VCC.
5
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS(CONTINUED)
Symbol
Name
I/O
Description
W/RA
Port-AWrite/
ReadSelect
I
A HIGHselects a write operationanda LOWselects a readoperationonPortAfora LOW-to-HIGH
transitionofCLKA.TheA0-A35outputs areintheHIGHimpedancestatewhenW/RAis HIGH.
W/RB
Port-BWrite/
ReadSelect
I
A LOWselects a write operationanda HIGHselects a readoperationonPortBfora LOW-to-HIGH
transitionofCLKB.TheB0-B35outputsareintheHIGHimpedancestatewhenW/RBisLOW.
6
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR
TEMPERATURE RANGE (Unless otherwise noted)(1)
Symbol
Rating
Commercial
–0.5to+7.0
–0.5 to VCC+0.5
–0.5 to VCC+0.5
±20
Unit
V
VCC
SupplyVoltageRange
InputVoltageRange
OutputVoltageRange
(2)
VI
V
(2)
VO
V
IIK
Input Clamp Current (VI < 0 or VI > VCC)
Output Clamp Current (VO = < 0 or VO > VCC)
Continuous Output Current (VO = 0 to VCC)
Continuous Current Through VCC or GND
StorageTemperatureRange
mA
mA
mA
mA
°C
IOK
±50
IOUT
ICC
±50
±400
TSTG
–65 to 150
NOTES:
1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these
or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect
device reliability.
2. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed.
RECOMMENDEDOPERATINGCONDITIONS
Symbol
VCC
VIH
Parameter
SupplyVoltage
Min.
4.5
2
Max.
5.5
–
Unit
V
HIGH Level Input Voltage
LOW-LevelInputVoltage
HIGH-Level Output Current
LOW-Level Output Current
OperatingFree-airTemperature
V
VIL
–
0.8
–4
V
IOH
–
mA
mA
°C
IOL
–
8
TA
0
70
ELECTRICALCHARACTERISTICSOVERRECOMMENDEDOPERATING
FREE-AIRTEMPERATURERANGE(Unlessotherwisenoted)
IDT723654
IDT723664
IDT723674
Commercial
tCLK = 12, 15ns
Symbol
VOH
VOL
Parameter
OutputLogic"1"Voltage
OutputLogic"0"Voltage
InputLeakageCurrent(AnyInput)
OutputLeakageCurrent
Test Conditions
IOH = –4 mA
Min.
2.4
—
—
—
—
—
—
—
Typ.(1)
—
—
—
—
—
—
4
Max.
—
0.5
±10
±10
8
Unit
V
VCC = 4.5V,
VCC = 4.5V,
VCC = 5.5V,
VCC = 5.5V,
IOL = 8 mA
V
ILI
VI = VCC or 0
µ A
µ A
mA
mA
pF
ILO
VO = VCC or 0
VI = VCC –0.2V or 0V
VI = VCC –0.2V or 0V
f = 1 MHz
ICC2(2)
ICC3(2)
Standby Current (with CLKA & CLKB running) VCC = 5.5V,
StandbyCurrent(noclocksrunning)
InputCapacitance
VCC = 5.5V,
VI = 0,
1
(3)
CIN
—
—
(3)
COUT
OutputCapacitance
VO = 0,
f = 1 MHZ
8
pF
NOTES:
1. All typical values are at VCC = 5V, TA = 25°C.
2. For additional ICC information, see Figure 1, Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS).
3. Characterized values, not currently tested.
4. Industrial temperature range is available by special order.
7
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
DETERMINING ACTIVE CURRENT CONSUMPTION AND POWER DISSIPATION
The ICC(f) current for the graph in Figure 1 was taken while simultaneously reading and writing a FIFO on the IDT723654/723664/723674 with CLKA
andCLKBsettofS. Alldatainputsanddataoutputschangestateduringeachclockcycletoconsumethehighestsupplycurrent. Dataoutputsweredisconnected
tonormalizethegraphtoazerocapacitanceload. Oncethecapacitanceloadperdata-outputchannelandthenumberofthesedevice'sinputsdrivenbyTTL
HIGHlevels areknown,thepowerdissipationcanbecalculatedwiththeequationbelow.
CALCULATING POWER DISSIPATION
WithICC(f) takenfromFigure1,themaximumpowerdissipation(PT)oftheseFIFOs maybecalculatedby:
2
PT = VCC x ICC(f) + Σ(CL x VCC x fo)
N
where:
N
= number of used outputs (36-bit (long word), 18-bit (word) or 9-bit (byte) bus size)
CL = outputcapacitanceload
fo = switchingfrequencyofanoutput
300
fdata = 1/2 fS
TA = 25oC
CL = 0 pF
250
200
150
VCC = 5.5V
VCC = 5.0V
VCC = 4.5V
100
50
0
0
10
20
30
40
50
60
70
80
90
5608drw03
fS Clock Frequency MHz
Figure 1. Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS)
8
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
TIMING REQUIREMENTS OVER RECOMMENDED RANGES OF SUPPLY
VOLTAGE AND OPERATING FREE-AIR TEMPERATURE
(Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C)
Commercial
IDT723654L12
IDT723664L12
IDT723674L12
IDT723654L15
IDT723664L15
IDT723674L15
Symbol
fS
Parameter
Min.
—
12
5
Max.
83
Min.
—
15
6
Max.
66.7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unit
MHz
ns
Clock Frequency, CLKA or CLKB
tCLK
tCLKH
tCLKL
tDS
Clock Cycle Time, CLKA or CLKB
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Pulse Duration, CLKA or CLKB HIGH
ns
PulseDuration, CLKAandCLKBLOW
5
6
ns
SetupTime, A0-A35before CLKA↑andB0-B35before CLKB↑
SetupTime,CSA andW/RAbefore CLKA↑;CSB andW/RBbefore CLKB↑
Setup Time, ENA, and MBA before CLKA↑;ENB, andMBBbefore CLKB↑
Setup Time, MRS1, MRS2, PRS1, or PRS2 LOW before CLKA↑or CLKB↑
Setup Time, FS0, FS1, FS2 before MRS1 and MRS2 HIGH
SetupTime, BE/FWFT beforeMRS1 andMRS2HIGH
SetupTime,FS0/SDbeforeCLKA↑
3
4
ns
tENS1
tENS2
tRSTS
tFSS
4
4.5
4.5
5
ns
3
ns
(1)
5
ns
7.5
7.5
3
7.5
7.5
4
ns
tBES
ns
tSDS
ns
tSENS
tFWS
tRTMS
tDH
SetupTime,FS1/SENbeforeCLKA↑
3
4
ns
SetupTime,BE/FWFTbeforeCLKA↑
0
0
ns
Setup Time, RTM before RT1; RTM before RT2
HoldTime,A0-A35afterCLKA↑andB0-B35afterCLKB↑
5
5
ns
0.5
0.5
1
ns
tENH
Hold Time, CSA, W/RA, ENA, and MBA after CLKA↑; CSB, W/RB, ENB, and
MBBafterCLKB↑
1
ns
(1)
tRSTH
tFSH
Hold Time, MRS1, MRS2, PRS1 or PRS2 LOW after CLKA↑ or CLKB↑
4
2
—
—
—
—
—
—
—
—
4
2
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
Hold Time, FS0, FS1, FS2 after MRS1 and MRS2 HIGH
Hold Time, BE/FWFT after MRS1 and MRS2 HIGH
HoldTime, FS0/SDafterCLKA↑
tBEH
2
2
tSDH
0.5
0.5
2
1
tSENH
tSPH
HoldTime,FS1/SENHIGHafterCLKA↑
1
Hold Time, FS1/SEN HIGH after MRS1 and MRS2 HIGH
HoldTime, RTMafterRT1;RTMafterRT2
2
tRTMH
tSKEW1(2)
5
5
SkewTime betweenCLKA↑andCLKB↑ forEFA/ORA,EFB/ORB,FFA/IRA,
and FFB/IRB
5
7.5
tSKEW2(2.3) Skew Time between CLKA↑ and CLKB↑ for AEA, AEB, AFA, and AFB
12
—
12
—
ns
NOTES:
1. Requirement to count the clock edge as one of at least four needed to reset a FIFO.
2. Skew time is not a timing constraint for proper device operation and is only included to illustrate the timing relationship between CLKA cycle and CLKB cycle.
3. Design simulated, not tested.
4. Industrial temperature range is available by special order.
9
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
SWITCHING CHARACTERISTICS OVER RECOMMENDED RANGES OF SUPPLY
VOLTAGE AND OPERATING FREE-AIR TEMPERATURE, CL = 30pF
(Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C)
Commercial
IDT723654L12 IDT723654L15
IDT723664L12 IDT723664L15
IDT723674L12 IDT723674L15
Symbol
tA
Parameter
Min. Max. Min Max. Unit
Access Time,CLKA↑toA0-A35andCLKB↑toB0-B35
Propagation Delay Time, CLKA↑ toFFA/IRAandCLKB↑ toFFB/IRB
PropagationDelayTime,CLKA↑toEFA/ORAandCLKB↑ toEFB/ORB
PropagationDelayTime, CLKA↑toAEAandCLKB↑toAEB
PropagationDelayTime, CLKA↑toAFAandCLKB↑toAFB
2
2
1
1
1
0
8
8
8
8
8
8
2
2
1
1
1
0
10
8
ns
ns
ns
ns
ns
ns
tWFF
tREF
tPAE
tPAF
tPMF
8
8
8
Propagation Delay Time, CLKA↑ to MBF1 LOW or MBF2 HIGH and CLKB↑ to MBF2
LOW or MBF1 HIGH
8
tPMR
tMDV
tRSF
PropagationDelayTime, CLKA↑ toB0-B35(1)andCLKB↑toA0-A35(2)
2
2
1
8
8
2
2
1
10
10
15
ns
ns
ns
Propagation Delay Time, MBA to A0-A35 valid and MBB to B0-B35 valid
Propagation Delay Time, MRS1 or PRS1 LOW to AEB LOW, AFA HIGH, and MBF1 HIGH
and MRS2 or PRS2 LOW to AEA LOW, AFB HIGH, and MBF2 HIGH
10
tEN
tDIS
Enable Time, CSA or W/RA LOW to A0-A35 Active and CSB LOW and W/RB
2
1
6
6
2
1
10
8
ns
ns
HIGH to B0-B35 Active
Disable Time, CSA or W/RA HIGH to A0-A35 at high impedance and CSB HIGH
orW/RBLOWtoB0-B35athighimpedance.
NOTES:
1. Writing data to the mail1 register when the B0-B35 outputs are active and MBB is HIGH.
2. Writing data to the mail2 register when the A0-A35 outputs are active and MBA is HIGH.
3. Industrial temperature range is available by special order.
10
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
and four Port B Clock (CLKB) LOW-to-HIGH transitions. The Retransmit
initializesthereadpointerofFIFO1tothefirstmemorylocation.
The FIFO2 memory undergoes a Retransmit by taking its associated
Retransmit(RT2)inputLOWforatleastfourPortAClock(CLKA)andfourPort
CClock(CLKC)LOW-to-HIGHtransitions.TheRetransmitinitializestheread
pointerofFIFO2tothefirstmemorylocation.
TheRTMpinmustbeHIGHduringthetimeofRetransmit.Notethatthe RT1
inputismuxedwiththePRS1input,thestateoftheRTMpindeterminingwhether
thispinperformsaRetransmitorPartialReset.Also,theRT2inputismuxed
with the PRS2 input, the state of the RTM pin determining whether this pin
performsaRetransmitorPartialReset.
SIGNALDESCRIPTION
MASTER RESET (MRS1, MRS2)
Afterpowerup,aMasterReset operationmustbeperformedbyproviding
aLOWpulsetoMRS1andMRS2simultaneously. Afterwards,eachofthetwo
FIFO memories of the IDT723654/723664/723674 undergoes a complete
resetbytakingitsassociatedMasterReset(MRS1,MRS2)inputLOWforat
leastfourPortAClock(CLKA)andfourPortBClock(CLKB)LOW-to-HIGH
transitions. TheMasterResetinputscanswitchasynchronouslytotheclocks.
AMasterReset initializes the associatedwrite andreadpointers tothe first
locationofthememoryandforces theFull/InputReadyflag(FFA/IRA,FFB/
IRB) LOW, the Empty/Output Ready flag (EFA/ORA, EFB/ORB) LOW, the
Almost-Emptyflag(AEA,AEB)LOWandforcestheAlmost-Fullflag(AFA,AFB)
HIGH. AMasterResetalsoforcestheassociatedMailboxFlag(MBF1,MFB2)
oftheparallelmailboxregisterHIGH. AfteraMasterReset,theFIFO's Full/
InputReadyflagissetHIGHaftertwowriteclockcycles. ThentheFIFOisready
tobewrittento.
BIG-ENDIAN/FIRST WORD FALL THROUGH (BE/FWFT)
— ENDIAN SELECTION
Thisisadualpurposepin.AtthetimeofMasterReset,theBEselectfunction
isactive,permittingachoiceofBigorLittle-Endianbytearrangementfordata
writtentoorreadfromPortB.This selectiondetermines theorderbywhich
bytes (orwords)ofdata are transferredthroughthis port. Forthe following
illustrations,assumethatabyte(orword)bussizehasbeenselectedforPort
B.(NotethatwhenPortBis configuredforalongwordsize,theBig-Endian
ALOW-to-HIGHtransitionontheFIFO1MasterReset(MRS1)inputlatches
thevaluesoftheBig-Endian(BE)inputfordeterminingtheorderbywhichbytes
aretransferredthroughPortB. Italso latchesthevaluesoftheFlagSelect(FS0,
FS1andFS2)inputs forchoosingthe Almost-FullandAlmost-Emptyoffset
programmingmethod.
1
functionhas noapplicationandthe BEinputis a “don’tcare” .)
A HIGH on the BE/FWFT input when the Master Reset (MRS1, MRS2)
inputsgofromLOWtoHIGHwillselectaBig-Endianarrangement.Whendata
ismovinginthedirectionfromPortAtoPortB,themostsignificantbyte(word)
ofthelongwordwrittentoPortAwillbereadfromPortBfirst;theleastsignificant
byte(word)ofthelongwordwrittentoPortAwillbereadfromPortBlast.When
data is movinginthe directionfromPortBtoPortA, the byte (word)written
toPortBfirstwillbereadfromPortAasthemostsignificantbyte(word)ofthe
long word; the byte (word) written to Port B last will be read from Port A as
theleastsignificantbyte(word)ofthelongword.
ALOW-to-HIGHtransitionontheFIFO2MasterReset(MRS2)clearsthe
Flag Offset Registers of FIFO2 (X2, Y2). A LOW-to-HIGH transition on the
FIFO2MasterReset(MRS2)togetherwiththeFIFO1MasterReset(MRS1)
inputlatchesthevalueoftheBig-Endian(BE)inputforPortBandalsolatches
thevaluesoftheFlagSelect(FS0,FS1andFS2)inputsforchoosingtheAlmost-
FullandAlmost-Emptyoffsetprogrammingmethod. (FordetailsseeTable1,
FlagProgramming,andtheProgrammingtheAlmost-EmptyandAlmost-Full
Flagssection). TherelevantFIFOMasterResettimingdiagramcanbefound
in Figure 3.
A LOW on the BE/FWFT input when the Master Reset (MRS1, MRS2)
inputsgofromLOWtoHIGHwillselectaLittle-Endianarrangement.Whendata
ismovinginthedirectionfromPortAtoPortB,theleastsignificantbyte(word)
ofthelongwordwrittentoPortAwillbereadfromPortBfirst;themostsignificant
byte(word)ofthelongwordwrittentoPortAwillbereadfromPortBlast.When
data is movinginthe directionfromPortBtoPortA, the byte (word)written
toPortBfirstwillbereadfromPortAastheleastsignificantbyte(word)ofthe
long word; the byte (word) written to Port B last will be read from Port A as
the most significant byte (word) of the long word. Refer to Figure 2 for an
illustrationoftheBEfunction.SeeFigure3(MasterReset)fortheEndianselect
timingdiagram.
PARTIAL RESET (PRS1, PRS2)
EachofthetwoFIFOmemoriesofthesedevicesundergoesalimitedreset
bytakingitsassociatedPartialReset(PRS1,PRS2)inputLOWforatleastfour
PortAClock(CLKA)andfourPortBClock(CLKB)LOW-to-HIGHtransitions.
ThePartialResetinputs canswitchasynchronouslytotheclocks.APartial
ResetinitializestheinternalreadandwritepointersandforcestheFull/Input
Readyflag(FFA/IRA,FFB/IRB)LOW,theEmpty/OutputReadyflag(EFA/
ORA, EFB/ORB) LOW, the Almost-Empty flag (AEA, AEB) LOW, and the
Almost-Fullflag(AFA,AFB)HIGH.APartialResetalsoforcestheMailboxFlag
(MBF1,MBF2)oftheparallelmailboxregisterHIGH.AfteraPartialReset,the
FIFO’s Full/InputReadyflagis setHIGHaftertwowrite clockcycles. Then
the FIFO is ready to be written to.
— TIMING MODE SELECTION
AfterMasterReset,theFWFTselectfunctionisactive,permittingachoice
betweentwopossibletimingmodes:IDTStandardmodeorFirstWordFall
Through (FWFT) mode. Once the Master Reset (MRS1, MRS2) input is
HIGH,aHIGHontheBE/FWFTinputduringthenextLOW-to-HIGHtransition
ofCLKA(forFIFO1)andCLKB(forFIFO2)willselectIDTStandardmode.
This modeuses theEmptyFlagfunction(EFA,EFB)toindicatewhetheror
not there are any words present in the FIFO memory. It uses the Full Flag
function(FFA,FFB)toindicatewhetherornottheFIFOmemoryhasanyfree
space for writing. In IDT Standard mode, every word read from the FIFO,
includingthefirst,mustberequestedusingaformalreadoperation.
Whateverflagoffsets,programmingmethod(parallelorserial),andtiming
mode(FWFTorIDTStandardmode)arecurrentlyselectedatthetimeaPartial
Resetisinitiated,thosesettingswillberemainunchangeduponcompletionof
the reset operation. A Partial Reset may be useful in the case where
reprogrammingaFIFOfollowingaMasterResetwouldbeinconvenient.See
Figure4forthePartialResettimingdiagram.
RETRANSMIT (RT1, RT2)
TheFIFO1memoryofthesedevicesundergoesaRetransmitbytakingits
associatedRetransmit (RT1)inputLOWforatleastfourPortAClock(CLKA)
NOTE:
1. Either a HIGH or LOW can be applied to a "don't care" input with no change to the logical operation of the FIFO. Nevertheless, inputs that are temporarily "don't care" (along with
unused inputs) must not be left open, rather they must be either HIGH or LOW.
11
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
orLOWduringamasterreset.Forexample,toloadthepresetvalueof64into
X1 and Y1, FS0, FS1 and FS2 must be HIGH when FlFO1 reset (MRS1)
returnsHIGH.Flag-offsetregistersassociatedwithFIFO2areloadedwithone
ofthepresetvaluesinthesamewaywithFIFO2MasterReset(MRS2),toggled
simultaneously with FIFO1 Master Reset (MRS1). For relevant preset value
loading timing diagram, see Figure 3.
OncetheMasterReset(MRS1,MRS2)inputis HIGH,aLOWontheBE/
FWFTinputduringthenextLOW-to-HIGHtransitionofCLKA(forFIFO1)and
CLKB(forFIFO2)willselectFWFTmode.ThismodeusestheOutputReady
function(ORA,ORB)toindicatewhetherornotthereisvaliddataatthedata
outputs(A0-A35orB0-B35).ItalsousestheInputReadyfunction(IRA,IRB)
toindicate whetherornotthe FIFOmemoryhas anyfree space forwriting.
IntheFWFTmode,thefirstwordwrittentoanemptyFIFOgoesdirectlytodata
outputs,noreadrequestnecessary. Subsequentwordsmustbeaccessed
byperforminga formalreadoperation.
— PARALLEL LOAD FROM PORT A
ToprogramtheX1,X2,Y1,andY2registersfromPortA,performaMaster
ResetonbothFlFOs simultaneouslywithFS2HIGHorLOW, FS0andFS1
LOWduringtheLOW-to-HIGHtransitionofMRS1andMRS2.ThestateofFS2
atthispointofresetwilldeterminewhethertheparallelprogrammingmethod
hasInterspersedParityorNon-InterspersedParity.RefertoTable1forFlag
Programming Flag Offset setup . It is important to note that once parallel
programminghasbeenselectedduringaMasterResetbyholdingbothFS0
& FS1 LOW, these inputs must remain LOW during all subsequent FIFO
operation. They can only be toggled HIGH when future Master Resets are
performedandotherprogrammingmethodsaredesired.
Afterthisresetiscomplete,thefirstfourwritestoFIFO1donotstoredatain
RAM but load the Offset registers in the order Y1, X1, Y2, X2. For Non-
InterspersedParitymodethePortAdatainputsusedbytheOffsetregistersare
(A10-A0), (A11-A0), or (A12-A0) for the IDT723654, IDT723664, or
IDT723674,respectively.ForInterspersedParitymodethePortAdatainputs
usedbytheOffsetregistersare(A11-A9,A7-A0),(A12-A9,A7-A0),or(A13-
A9,A7-A0)fortheIDT723654,IDT723664,orIDT723674,respectively. The
highestnumberedinputisusedasthemostsignificantbitofthebinarynumber
ineachcase.Validprogrammingvaluesfortheregistersrangefrom1to2,044
for the IDT723654; 1 to 4,092 for the IDT723664; and 1 to 8,188 for the
IDT723674.AfteralltheoffsetregistersareprogrammedfromPortA,thePortB
FollowingMasterReset,thelevelappliedtotheBE/FWFTinputtochoose
thedesiredtimingmodemustremainstaticthroughoutFIFOoperation.Refer
toFigure3(MasterReset)foraFirstWordFallThroughselecttimingdiagram.
PROGRAMMINGTHEALMOST-EMPTYANDALMOST-FULLFLAGS
FourregistersintheIDT723654/723664/723674areusedtoholdtheoffset
valuesfortheAlmost-EmptyandAlmost-Fullflags.ThePortBAlmost-Empty
flag(AEB)OffsetregisterislabeledX1andthePortAAlmost-Emptyflag(AEA)
OffsetregisterislabeledX2.ThePortAAlmost-Fullflag(AFA)Offsetregister
islabeledY1andthePortBAlmost-Fullflag(AFB)OffsetregisterislabeledY2.
TheindexofeachregisternamecorrespondstoitsFIFOnumber.Theoffset
registers can be loaded with preset values during the reset of a FIFO,
programmedinparallelusingtheFIFO’sPortAdatainputs,orprogrammed
in serial using the Serial Data (SD) input (see Table 1).
FS0/SD,FS1/SENandFS2functionthesamewayinbothIDTStandard
andFWFTmodes.
— PRESET VALUES
ToloadaFIFO’sAlmost-EmptyflagandAlmost-FullflagOffsetregisterswith
oneofthefivepresetvalueslistedinTable1,theflagselectinputsmustbeHIGH
TABLE 1 — FLAG PROGRAMMING
FS2
FS1/SEN
FS0/SD
MRS1
MRS2
X1 AND Y1 REGlSTERS(1)
X2 AND Y2 REGlSTERS(2)
H
H
H
H
H
H
L
L
L
L
L
H
L
H
H
H
H
L
L
H
H
L
L
H
L
L
H
H
L
↑
X
↑
X
↑
X
↑
X
↑
X
↑
↑
↑
X
↑
X
↑
X
↑
X
↑
X
↑
↑
↑
↑
64
X
X
64
16
X
L
X
16
H
H
H
H
H
H
L
8
X
X
8
256
X
X
256
1,024
X
1,024
X
SerialprogrammingviaSD
SerialprogrammingviaSD
(3,5)
(3,5)
L
ParallelprogrammingviaPortA
ParallelprogrammingviaPortA
IP Mode(4, 5)
L
IP Mode(4, 5)
NOTES:
1. X1 register holds the offset for AEB; Y1 register holds the offset for AFA.
2. X2 register holds the offset for AEA; Y2 register holds the offset for AFB.
3. When this method of parallel programming is selected, Port A will assume Non-Interspersed Parity.
4. When IP Mode is selected, only parallel programming of the offset values via Port A, can be performed and Port A will assume Interspersed Parity.
5. IF parallel programming is selected during a Master Reset, then FS0 & FS1 must remain LOW during FIFO operation.
12
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
Full/Input Ready flag (FFB/IRB) is set HIGH, and both FIFOs begin normal
operation. Refer to Figure 5 for a timing diagram illustration of parallel
programmingoftheflagoffsetvalues.
offsetvalues,thedevicewillignoredatalineA8.IfNon-InterspersedParityis
selectedthendatalineA8willbecomeavalidbit.IfInterspersedParityisselected
serialprogrammingoftheoffsetvaluesisnotpermitted,onlyparallelprogram-
ming can be done.
INTERSPERSED PARITY
InterspersedParityisselectedduringaMasterResetoftheFIFO.Referto
Table1fortheset-upconfigurationofInterspersedParity.TheInterspersed
Parityfunctionallowstheusertoselectthelocationoftheparitybitsintheword
loadedintotheparallelport(A0-An)duringprogrammingoftheflagoffsetvalues.
IfInterspersedParityisselectedthenduringparallelprogrammingoftheflag
— SERIAL LOAD
ToprogramtheX1,X2,Y1,andY2registersserially,initiateaMasterReset
withFS2LOW,FS0/SDLOWandFS1/SENHIGHduringtheLOW-to-HIGH
transitionofMRS1andMRS2.Afterthisresetiscomplete,theXandYregister
valuesareloadedbit-wisethroughtheFS0/SDinputoneachLOW-to-HIGH
TABLE 2 — PORT A ENABLE FUNCTION TABLE
CSA
W/RA
ENA
MBA
CLKA
Data A (A0-A35) I/O
Port Function
H
L
L
L
L
L
L
X
H
H
L
X
H
H
L
X
L
X
↑
↑
X
↑
X
↑
High-Impedance
Input
None
FIFO1 write
Mail1write
H
L
Input
Output
None
L
H
L
L
Output
FIFO2read
L
H
H
Output
None
L
H
Output
Mail2 read (set MBF2 HIGH)
TABLE 3 — PORT B ENABLE FUNCTION TABLE
CSB
W/RB
ENB
MBB
CLKB
Data B (B0-B35) I/O
Port Function
H
L
L
L
L
L
L
L
X
L
X
L
X
X
L
X
X
↑
High-Impedance
Input
None
None
L
H
H
L
Input
FIFO2 write
Mail2write
L
H
L
↑
Input
H
H
H
H
X
↑
Output
Output
Output
Output
None
H
L
L
FIFO1read
None
H
H
X
↑
H
Mail1 read (set MBF1 HIGH)
FIFO WRITE/READ OPERATION
transitionofCLKAthattheFS1/SENinputisLOW.Thereare44-,48-,or52-
bitwritesneededtocompletetheprogrammingfortheIDT723654,IDT723664,
orIDT723674,respectively.ThefourregistersarewrittenintheorderY1,X1,
Y2,andfinally,X2. Thefirst-bitwritestoresthemostsignificantbitoftheY1register
andthelast-bitwritestorestheleastsignificantbitoftheX2register.Eachregister
valuecanbeprogrammedfrom1to2,044(IDT723654),1to4,092(IDT723664),
or 1 to 8,188 (IDT723674).
Whentheoptiontoprogramtheoffsetregistersseriallyischosen,thePortA
Full/InputReady(FFA/IRA)flagremainsLOWuntilallregisterbitsarewritten.
FFA/IRAissetHIGHbytheLOW-to-HIGHtransitionofCLKAafterthelastbit
isloadedtoallownormalFIFO1operation.ThePortBFull/InputReady(FFB/
IRB)flagalsoremainsLOWthroughouttheserialprogrammingprocess,until
allregisterbitsarewritten.FFB/IRBissetHIGHbytheLOW-to-HIGHtransition
ofCLKBafterthelastbitisloadedtoallownormalFIFO2operation. SeeFigure 6
forSerialProgrammingoftheAlmost-FullFlagandAlmost-EmptyFlagOffset
Values (IDT Standard and FWFT Modes) timing diagram.
ThestateofthePortAdata(A0-A35)linesiscontrolledbyPortAChipSelect
(CSA)andPortAWrite/Readselect(W/RA).TheA0-A35linesareintheHigh-
impedance state wheneitherCSA orW/RAis HIGH. The A0-A35lines are
active outputs whenbothCSA andW/RAare LOW.
Data is loaded into FIFO1 from the A0-A35 inputs on a LOW-to-HIGH
transitionofCLKAwhenCSAisLOW,W/RAisHIGH,ENAisHIGH,MBAis
LOW,andFFA/IRAisHIGH.DataisreadfromFIFO2totheA0-A35outputs
by a LOW-to-HIGH transition of CLKA when CSA is LOW, W/RA is LOW,
ENA is HIGH, MBA is LOW, and EFA/ORA is HIGH (see Table 2). FIFO
reads and writes on Port A are independent of any concurrent Port B
operation.
The Port B control signals are identical to those of Port A with the
exceptionthatthePortBWrite/Readselect(W/RB)istheinverseofthePort
A Write/Read select (W/RA). The state of the Port B data (B0-B35) lines is
controlledbythePortBChipSelect(CSB)andPortBWrite/Readselect(W/
13
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
TABLE 4 — FIFO1 FLAG OPERATION (IDT Standard and FWFT modes)
Synchronized
to CLKB
Synchronized
to CLKA
Number of Words in FIFO Memory(1,2)
(3)
(3)
(3)
IDT723654
IDT723664
IDT723674
EFB/ORB
AEB
AFA
FFA/IRA
0
1toX1
0
1toX1
0
1toX1
L
H
H
H
H
L
L
H
H
H
L
H
H
H
H
L
(X1+1)to[2,048-(Y1+1)]
(2,048-Y1)to2,047
2,048
(X1+1)to[4,096-(Y1+1)]
(4,096-Y1)to4,095
4,096
(X1+1)to[8,192-(Y1+1)]
(8,192-Y1)to8,191
8,192
H
H
H
L
NOTES:
1. When a word loaded to an empty FIFO is shifted to the output register, its previous FIFO memory location is free.
2. Data in the output register does not count as a "word in FIFO memory". Since in FWFT mode, the first word written to an empty FIFO goes unrequested to the output register (no read
operation necessary), it is not included in the FIFO memory count.
3. X1 is the Almost-Empty offset for FIFO1 used by AEB. Y1 is the Almost-Full offset for FIFO1 used by AFA. Both X1 and Y1 are selected during a FIFO1 reset or port A programming.
4. The ORB and IRA functions are active during FWFT mode; the EFB and FFA functions are active in IDT Standard mode.
TABLE 5 — FIFO2 FLAG OPERATION (IDT Standard and FWFT modes)
Synchronized
to CLKA
Synchronized
to CLKB
Number of Words in FIFO Memory(1,2)
(3)
(3)
(3)
IDT723654
IDT723664
IDT723674
EFA/ORA
AEA
AFB
H
FFB/IRB
0
1toX2
0
1toX2
0
1toX2
L
H
H
H
H
L
L
H
H
H
H
L
H
(X2+1)to[2,048-(Y2+1)]
(2,048-Y2)to2,047
2,048
(X2+1)to[4,096-(Y2+1)]
(4,096-Y2)to4,095
4,096
(X2+1)to[8,192-(Y2+1)]
(8,192-Y2)to8,191
8,192
H
H
H
H
L
L
NOTES:
1. When a word loaded to an empty FIFO is shifted to the output register, its previous FIFO memory location is free.
2. Data in the output register does not count as a "word in FIFO memory". Since in FWFT mode, the first word written to an empty FIFO goes unrequested to the output register (no read
operation necessary), it is not included in the FIFO memory count.
3. X2 is the Almost-Empty offset for FIFO2 used by AEA. Y2 is the Almost-Full offset for FIFO2 used by AFB. Both X2 and Y2 are selected during a FIFO2 reset or port A programming.
4. The ORA and IRB functions are active during FWFT mode; the EFA and FFB functions are active in IDT Standard mode.
RB).TheB0-B35lines areinthehigh-impedancestatewheneitherCSB is
HIGH or W/RB is LOW. The B0-B35 lines are active outputs when CSB is
LOW and W/RB is HIGH.
WhentheOutputReadyflagisHIGH,subsequentdataisclockedtotheoutput
registersonlywhenareadisselectedusingtheport’sChipSelect,Write/Read
select,Enable,andMailboxselect.
Data is loaded into FIFO2 from the B0-B35 inputs on a LOW-to-HIGH
transitionofCLKBwhenCSBisLOW,W/RBisLOW,ENBisHIGH,MBBis
LOW,andFFB/IRBisHIGH.DataisreadfromFIFO1totheB0-B35outputs
byaLOW-to-HIGHtransitionofCLKBwhenCSBisLOW,W/RBisHIGH,ENB
isHIGH,MBBisLOW,andEFB/ORBisHIGH(seeTable3).FIFOreadsand
writes on Port B are independent of any concurrent Port A operation.
ThesetupandholdtimeconstraintstotheportclocksfortheportChipSelects
andWrite/Readselectsareonlyforenablingwriteandreadoperationsand
arenotrelatedtohigh-impedancecontrolofthedataoutputs.Ifaportenable
isLOWduringaclockcycle,theport’sChipSelectandWrite/Readselectmay
changestates duringthesetupandholdtimewindowofthecycle.
WhenoperatingtheFIFOinFWFTmodeandtheOutputReadyflagisLOW,
thenextwordwrittenisautomaticallysenttotheFIFO’soutputregisterbythe
LOW-to-HIGHtransitionoftheportclockthatsetstheOutputReadyflagHIGH.
WhenoperatingtheFIFOinIDTStandardmode,thefirstwordwillcause
theEmptyFlagtochangestateonthesecondLOW-to-HIGHtransitionofthe
ReadClock. Thedatawordwillnotbeautomaticallysenttotheoutputregister.
Instead, data residing in the FIFO's memory array is clocked to the output
registeronlywhenareadisselectedusingtheport’sChipSelect,Write/Read
select,Enable,andMailboxselect.WriteandreadtimingdiagramsforPortA
canbefoundinFigure7and14. RelevantPortBwriteandreadcycle timing
diagrams togetherwithBus-MatchingandEndianselectoperations canbe
found in Figures 8 through 13.
SYNCHRONIZED FIFO FLAGS
Each FIFO is synchronized to its port clock through at least two flip-flop
stages.Thisisdonetoimproveflag-signalreliabilitybyreducingtheprobability
ofmetastableeventswhenCLKAandCLKBoperateasynchronouslytoone
14
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
twocyclesoftheFull/InputReadyflagsynchronizingclockhaveelapsedsince
the nextmemorywrite locationhas beenread. The secondLOW-to-HIGH
transitionontheFull/InputReadyflagsynchronizingclockafterthereadsets
the Full/InputReadyflagHIGH.
another. EFA/ORA, AEA, FFA/IRA, and AFA are synchronized to CLKA.
EFB/ORB,AEB,FFB/IRB,andAFBaresynchronizedtoCLKB.Tables4and
5 show the relationship of each port flag to FIFO1 and FIFO2.
EMPTY/OUTPUTREADYFLAGS(EFA/ORA,EFB/ORB)
ALOW-to-HIGHtransitiononaFull/InputReadyflagsynchronizingclock
beginsthefirstsynchronizationcycleofareadiftheclocktransitionoccursat
timetSKEW1orgreateraftertheread.Otherwise,thesubsequentclockcycle
can be the first synchronization cycle (see Figures 19, 20, 21, and 22).
Thesearedualpurposeflags. IntheFWFTmode,theOutputReady(ORA,
ORB)functionisselected.WhentheOutput-ReadyflagisHIGH,newdatais
presentintheFIFOoutputregister.WhentheOutputReadyflagisLOW,the
previousdatawordispresentintheFIFOoutputregisterandattemptedFIFO
reads are ignored.
ALMOST-EMPTYFLAGS(AEA,AEB)
IntheIDTStandardmode,theEmptyFlag(EFA,EFB)functionisselected.
WhentheEmptyFlagisHIGH,dataisavailableintheFIFO’sRAMmemory
forreadingtotheoutputregister.WhentheEmptyFlagisLOW,theprevious
datawordispresentintheFIFOoutputregisterandattemptedFIFOreadsare
ignored.
TheEmpty/OutputReadyflagofaFIFOis synchronizedtotheportclock
thatreadsdatafromitsarray.ForboththeFWFTandIDTStandardmodes,
theFIFOreadpointeris incrementedeachtimeanewwordis clockedtoits
outputregister.ThestatemachinethatcontrolsanOutputReadyflagmonitors
a write pointer and read pointer comparator that indicates when the FIFO
memorystatusisempty,empty+1,orempty+2.
TheAlmost-EmptyflagofaFIFOissynchronizedtotheportclockthatreads
data from its array. The state machine that controls an Almost-Empty flag
monitorsawritepointerandreadpointercomparatorthatindicateswhenthe
FIFOmemorystatusisalmost-empty,almost-empty+1,oralmost-empty+2.
Thealmost-emptystateisdefinedbythecontentsofregisterX1forAEBand
registerX2forAEA.Theseregistersareloadedwithpresetvaluesduringa
FIFOreset,programmedfromPortA,orprogrammedserially(seeAlmost-
Empty flag and Almost-Full flag offset programming section). An Almost-
EmptyflagisLOWwhenitsFIFOcontainsXorlesswordsandisHIGHwhen
itsFIFOcontains(X+1)ormorewords.AdatawordpresentintheFIFOoutput
registerhas beenreadfrommemory.
InFWFTmode,fromthetimeawordis writtentoaFIFO,itcanbeshifted
totheFIFOoutputregisterinaminimumofthreecyclesoftheOutputReady
flagsynchronizingclock. Therefore, anOutputReadyflagis LOWifa word
inmemoryisthenextdatatobesenttotheFlFOoutputregisterandthreecycles
oftheportClockthatreadsdatafromtheFIFOhavenotelapsedsincethetime
thewordwaswritten.TheOutputReadyflagoftheFIFOremainsLOWuntil
thethirdLOW-to-HIGHtransitionofthesynchronizingclockoccurs,simulta-
neouslyforcingtheOutputReadyflagHIGHandshiftingthewordtotheFIFO
outputregister.
InIDTStandardmode,fromthetimeawordiswrittentoaFIFO,theEmpty
Flagwillindicatethepresenceofdataavailableforreadinginaminimumof
twocyclesoftheEmptyFlagsynchronizingclock.Therefore,anEmptyFlag
isLOWifawordinmemoryisthenextdatatobesenttotheFlFOoutputregister
andtwocyclesoftheportClockthatreadsdatafromtheFIFOhavenotelapsed
sincethetimethewordwaswritten.TheEmptyFlagoftheFIFOremainsLOW
untilthesecondLOW-to-HIGHtransitionofthesynchronizingclockoccurs,
forcing the Empty Flag HIGH; only then can data be read.
TwoLOW-to-HIGHtransitionsoftheAlmost-Emptyflagsynchronizingclock
arerequiredafteraFIFOwriteforitsAlmost-Emptyflagtoreflectthenewlevel
offill.Therefore,theAlmost-FullflagofaFIFOcontaining(X+1)ormorewords
remainsLOWiftwocyclesofitssynchronizingclockhavenotelapsedsince
thewritethatfilledthememorytothe(X+1)level.AnAlmost-Emptyflagisset
HIGHbythesecondLOW-to-HIGHtransitionofitssynchronizingclockafter
theFIFOwritethatfillsmemorytothe(X+1)level.ALOW-to-HIGHtransition
ofanAlmost-Emptyflagsynchronizingclockbeginsthefirstsynchronization
cycleifitoccurs attimetSKEW2 orgreaterafterthewritethatfills theFIFOto
(X+1)words.Otherwise,thesubsequentsynchronizingclockcyclemaybe
the first synchronization cycle. (See Figure 23 and 24).
ALMOST-FULLFLAGS(AFA, AFB)
TheAlmost-FullflagofaFIFOissynchronizedtotheportclockthatwrites
datatoitsarray.ThestatemachinethatcontrolsanAlmost-Fullflagmonitors
a write pointer and read pointer comparator that indicates when the FIFO
memorystatusisalmost-full,almost-full-1,oralmost-full-2.Thealmost-fullstate
isdefinedbythecontentsofregisterY1forAFAandregisterY2forAFB.These
registersareloadedwithpresetvaluesduringaFlFOreset,programmedfrom
PortA,orprogrammedserially(seeAlmost-EmptyflagandAlmost-Fullflag
offsetprogrammingsection).AnAlmost-FullflagisLOWwhenthenumberof
wordsinitsFIFOisgreaterthanorequalto(2,048-Y),(4,096-Y),or(8,192-Y)
fortheIDT723654,IDT723664,orIDT723674respectively.AnAlmost-Full
flag is HIGH when the number of words in its FIFO is less than or equal to
[2,048-(Y+1)],[4,096-(Y+1)],or[8,192-(Y+1)]fortheIDT723654,IDT723664,
orIDT723674respectively.NotethatadatawordpresentintheFIFOoutput
registerhas beenreadfrommemory.
TwoLOW-to-HIGHtransitionsoftheAlmost-Fullflagsynchronizingclock
arerequiredafteraFIFOreadforitsAlmost-Fullflagtoreflectthenewlevel
offill.Therefore,theAlmost-FullflagofaFIFOcontaining[2,048/4,096/8,192-
(Y+1)]orlesswordsremainsLOWiftwocyclesofitssynchronizingclockhave
notelapsedsince the readthatreducedthe numberofwords inmemoryto
[2,048/4,096/8,192-(Y+1)]. An Almost-Full flag is set HIGH by the second
LOW-to-HIGHtransitionofits synchronizingclockafterthe FIFOreadthat
reduces the number of words in memory to [2,048/4,096/8,192-(Y+1)]. A
LOW-to-HIGHtransitionofanAlmost-Fullflagsynchronizingclockbeginsthe
firstsynchronizationcycleifitoccursattime tSKEW2 orgreateraftertheread
ALOW-to-HIGHtransitiononanEmpty/OutputReadyflagsynchronizing
clockbeginsthefirstsynchronizationcycleofawriteiftheclocktransitionoccurs
attimetSKEW1orgreaterafterthewrite.Otherwise,thesubsequentclockcycle
can be the first synchronization cycle (see Figures 15, 16, 17, and 18).
FULL/INPUT READY FLAGS (FFA/IRA, FFB/IRB)
Thisisadualpurposeflag.InFWFTmode,theInputReady(IRAandIRB)
function is selected. In IDT Standard mode, the Full Flag (FFA and FFB)
functionisselected.Forbothtimingmodes,whentheFull/InputReadyflagis
HIGH,amemorylocationisfreeintheFIFOtoreceivenewdata.Nomemory
locationsarefreewhentheFull/InputReadyflagisLOWandattemptedwrites
to the FIFO are ignored.
The Full/InputReadyflagofa FlFOis synchronizedtothe portclockthat
writesdatatoitsarray.ForbothFWFTandIDTStandardmodes,eachtime
awordiswrittentoaFIFO,itswritepointerisincremented.Thestatemachine
thatcontrolsaFull/InputReadyflagmonitorsawritepointerandreadpointer
comparatorthatindicateswhentheFlFOmemorystatusisfull,full-1,orfull-2.
FromthetimeawordisreadfromaFIFO,itspreviousmemorylocationisready
to be written to in a minimum of two cycles of the Full/Input Ready flag
synchronizingclock.Therefore,anFull/InputReadyflagisLOWiflessthan
15
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
thatreducesthenumberofwordsinmemoryto[2,048/4,096/8,192-(Y+1)]. BUS SIZING
Otherwise,thesubsequentsynchronizingclockcyclemaybethefirstsynchro-
nization cycle (see Figure 25 and 26).
The PortBbus canbe configuredina 36-bitlongword,18-bitword,or9-
bit byte format for data read from FIFO1 or written to FIFO2. The levels
appliedtothePortBBusSizeselect(SIZE)andtheBus-Matchselect(BM)
determinethePortBbussize.TheselevelsshouldbestaticthroughoutFIFO
MAILBOX REGISTERS
Each FIFO has a 36-bit bypass register to pass command and control operation. Both bus size selections are implemented at the completion of
informationbetweenPortAandPortBwithoutputtingitinqueue.TheMailbox MasterReset,bythetimetheFull/InputReadyflagissetHIGH,asshownin
select(MBA, MBB)inputs choose betweena mailregisteranda FIFOfora Figure 2.
port data transfer operation. The usable width of both the Mail1 and Mail2
registersmatchestheselectedbussizeforPortB.
TwodifferentmethodsforsequencingdatatransferareavailableforPort
Bwhenthebussizeselectioniseitherbyte-orword-size.Theyarereferred
ALOW-to-HIGHtransitiononCLKAwritesdatatotheMail1Registerwhen toasBig-Endian(mostsignificantbytefirst)andLittle-Endian(leastsignificant
a Port A write is selected by CSA, W/RA, and ENA with MBA HIGH. If the bytefirst).ThelevelappliedtotheBig-Endianselect(BE)inputduringtheLOW-
selectedPortBbussizeisalso36bits,thentheusablewidthoftheMail1register to-HIGHtransitionofMRS1andMRS2selectstheendianmethodthatwillbe
employsdatalinesA0-A35.IftheselectedPortBbussizeis18bits,thenthe active during FIFO operation. BE is a don’t care input when the bus size
usablewidthoftheMail1RegisteremploysdatalinesA0-A17.(Inthiscase, selected for Port B is long word. The endian method is implemented at the
A18-A35aredon’tcareinputs.)IftheselectedPortBbus sizeis 9bits,then completionofMasterReset,bythetimetheFull/InputReadyflagissetHIGH,
theusablewidthoftheMail1RegisteremploysdatalinesA0-A8.(Inthiscase, as shown in Figure 2.
A9-A35 are don’t care inputs.)
Only36-bitlongworddataiswrittentoorreadfromthetwoFIFOmemories
ALOW-to-HIGHtransitiononCLKBwritesB0-B35datatotheMail2Register ontheIDT723654/723664/723674.Bus-matchingoperationsaredoneafter
whena PortBwrite is selectedbyCSB, W/RB,andENBwithMBBHIGH.If dataisreadfromtheFIFO1RAMandbeforedataiswrittentotheFIFO2RAM.
theselectedPortBbussizeisalso36bits,thentheusablewidthoftheMail2 Thesebus-matchingoperationsarenotavailablewhentransferringdatavia
employsdatalinesB0-B35.IftheselectedPortBbussizeis18bits,thenthe mailboxregisters.Furthermore,boththeword-andbyte-sizebusselections
usablewidthoftheMail2RegisteremploysdatalinesB0-B17.(Inthiscase, limitthewidthofthedatabusthatcanbeusedformailregisteroperations.In
B18-B35aredon’tcareinputs.)IftheselectedPortBbus sizeis 9bits,then thiscase,onlythosebytelanesbelongingtotheselectedword-orbyte-size
theusablewidthoftheMail2RegisteremploysdatalinesB0-B8.(Inthiscase, buscancarrymailboxdata.Theremainingdataoutputswillbeindeterminate.
B9-B35 are don’t care inputs.)
Theremainingdatainputswillbedon’tcareinputs.Forexample,whenaword-
Writingdatatoamailregistersetsitscorrespondingflag(MBF1orMBF2) sizebusisselected,thenmailboxdatacanbetransmittedonlybetweenA0-
LOW.AttemptedwritestoamailregisterareignoredwhilethemailflagisLOW. A17andB0-B17.Whenabyte-sizebusisselected,thenmailboxdatacanbe
Whendataoutputsofaportareactive,thedataonthebuscomesfromthe transmitted only between A0-A8 and B0-B8. (See Figures 27 and 28).
FIFOoutputregisterwhentheportMailboxselectinputisLOWandfromthe
mailregisterwhenthe portMailboxselectinputis HIGH.
BUS-MATCHING FIFO1 READS
TheMail1RegisterFlag(MBF1)issetHIGHbyaLOW-to-HIGHtransition
DataisreadfromtheFIFO1RAMin36-bitlongwordincrements.Ifalong
onCLKBwhenaPortBreadisselectedbyCSB,W/RB,andENBwithMBB wordbus sizeis implemented,theentirelongwordimmediatelyshifts tothe
HIGH. For a 36-bit bus size, 36 bits of mailbox data are placed on B0-B35. FIFO1outputregister.IfbyteorwordsizeisimplementedonPortB,onlythe
Foran18-bitbussize,18bitsofmailboxdataareplacedonB0-B17.(Inthis firstoneortwobytesappearontheselectedportionoftheFIFO1outputregister,
case,B18-B35areindeterminate.)Fora9-bitbussize,9bitsofmailboxdata with the rest of the long word stored in auxiliary registers. In this case,
are placed on B0-B8. (In this case, B9-B35 are indeterminate.)
subsequentFIFO1readsoutputtherestofthelongwordtotheFIFO1output
TheMail2RegisterFlag(MBF2)issetHIGHbyaLOW-to-HIGHtransition register in the order shown by Figure 2.
onCLKAwhenaPortAreadisselectedbyCSA,W/RA,andENAwithMBA
HIGH.
WhenreadingdatafromFIFO1inbyteorwordformat,theunusedB0-B35
outputsareindeterminate.
For a 36-bit bus size, 36 bits of mailbox data are placed on A0-A35. For
an18-bitbussize,18bitsofmailboxdataareplacedonA0-A17.(Inthiscase, BUS-MATCHING FIFO2 WRITES
A18-A35are indeterminate.)Fora 9-bitbus size, 9bits ofmailboxdata are
placedonA0-A8. (Inthis case, A9-A35are indeterminate.)
DataiswrittentotheFIFO2RAMin36-bitlongwordincrements.Datawritten
toFIFO2withabyteorwordbussizestorestheinitialbytesorwordsinauxiliary
Thedatainamailregisterremainsintactafteritisreadandchangesonly registers.TheCLKBrisingedgethatwritesthefourthbyteorthesecondword
whennewdataiswrittentotheregister.TheEndianselectfeaturehasnoeffect oflongwordtoFIFO2alsostorestheentirelongwordintheFIFO2memory.
onmailboxdata.FormailregisterandMailRegisterFlagtimingdiagrams,see The bytes are arranged in the manner shown in Figure 2.
Figure 27 and 28.
WhenwritingdatatoFIFO2inbyteorwordformat,theunusedB0-B35inputs
aredon'tcareinputs.
16
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
A35 A27
A26 A18
A17 A9
A8 A0
BYTE ORDER ON PORT A:
Write to FIFO1/
Read from FIFO2
D
A
B
C
B35 B27
B26 B18
B17 9
B8 B0
BYTE ORDER ON PORT B:
BE BM SIZE
Read from FIFO1/
Write to FIFO2
A
B
D
C
X
L
X
(a) LONG WORD SIZE
B35 B27
B35 B27
B26 B18
B26 B18
B17 B9
B8 B0
1st: Read from FIFO1/
Write to FIFO2
BE BM SIZE
A
B
H
H
L
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
C
D
(b) WORD SIZE
BIG ENDIAN
B17 B9
C
B35 B27
B35 B27
B26 B18
B8 B0
1st: Read from FIFO1/
Write to FIFO2
BE BM SIZE
D
L
H
L
B26 B18
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
A
B
(c) WORD SIZE
LITTLE-ENDIAN
B35 B27
B35 B27
B35 B27
B35 B27
B26 B18
B17 B9
B8 B0
BE BM SIZE
1st: Read from FIFO1/
Write to FIFO2
A
H
H
H
B26 B18
B26 B18
B26 B18
B17 B9
B17 B9
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
B
B8 B0
3rd: Read from FIFO1/
Write to FIFO2
C
B8 B0
4th: Read from FIFO1/
Write to FIFO2
D
(d) BYTE SIZE
BIG-ENDIAN
B35 B27
B35 B27
B35 B27
B35 B27
B26 B18
B17 B9
B8 B0
BE BM SIZE
1st: Read from FIFO1/
Write to FIFO2
D
L
H
H
B26 B18
B26 B18
B26 B18
B17 B9
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
C
B8 B0
3rd: Read from FIFO1/
Write to FIFO2
B
B17 B9
B8 B0
4th: Read from FIFO1/
Write to FIFO2
A
5608 drw 04
(e) BYTE SIZE
LITTLE-ENDIAN
Figure 2. Bus Sizing
17
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
t
RSTS
tRSTH
MRS1
tBEH
t
BES
tFWS
BE
0,1
BE/FWFT
FWFT
t
FSS
tFSH
FS2,
FS1,FS0
t
WFF
t
WFF
FFA/IRA
EFB/ORB
AEB
(3)
REF
t
t
RSF
t
RSF
AFA
t
RSF
MBF1
LOW
RTM
5608 drw 05
NOTES:
1. FIFO2 Master Reset (MRS2) is performed in the same manner to load X2 and Y2 with a preset value. For FIFO2 Master Reset, MRS1 must toggle simultaneously with MRS2.
2. PRS1 must be HIGH during Master Reset.
3. If BE/FWFT is HIGH, then EFB/ORB will go LOW one CLKB cycle earlier than in this case where BE/FWFT is LOW.
Figure 3. FIFO1 Master Reset and Loading X1 and Y1 with a Preset Value of Eight(1) (IDT Standard and FWFT Modes)
CLKA
CLKB
t
RSTS
tRSTH
PRS1
t
WFF
t
WFF
FFA/IRA
(3)
tREF
EFB/ORB
t
RSF
AEB
AFA
t
RSF
t
RSF
MBF1
RTM
LOW
5608 drw 06
NOTES:
1. Partial Reset is performed in the same manner for FIFO2.
2. MRS1 must be HIGH during Partial Reset.
3. If BE/FWFT is HIGH, then EFB/ORB will go LOW one CLKB cycle earlier than in this case where BE/FWFT is LOW.
Figure 4. FIFO1 Partial Reset(1) (IDT Standard and FWFT Modes)
18
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
2
1
4
MRS1,
MRS2
tFSS
tFSS
tFSH
tFSH
FS2
FS1,FS0
FFA/IRA
0,0
tWFF
tDS
(1)
tSKEW1
tENS2
tDH
tENH
ENA
A0-A35
AEB Offset
AFA Offset
AFB Offset
(Y 2)
AEA Offset
(X 2)
First Word to FIFO1
(X1)
(Y1)
CLKB
1
2
tWFF
FFB/IRB
5608 drw 07
NOTES:
1. tSKEW1 is the minimum time between the rising CLKA edge and a rising CLKB edge for FFB/IRB to transition HIGH in the next cycle. If the time between the rising edge of CLKA and rising
edge of CLKB is less than tSKEW1, then FFB/IRB may transition HIGH one CLKB cycle later than shown.
2. CSA=LOW, W/RA=HIGH,MBA=LOW. It is not necessary to program offset register on consecutive clock cycles.
Figure 5. Parallel Programming of the Almost-Full Flag and Almost-Empty Flag Offset Values after Reset
(IDT Standard and FWFT Modes)
CLKA
4
MRS1,
MRS2
t
FSS
tFSH
FS2
t
WFF
(1)
tSKEW
FFA/IRA
t
SENS
t
FSS
t
SENH
SDH
t
SENS
t
SENH
tSPH
FS1/SEN
tSDS
t
tSDH
tSDS
FS0/SD(3)
AFA Offset (Y1) MSB
AEA Offset (X2) LSB
CLKB
4
t
WFF
5608 drw08
FFB/IRB
NOTES:
1. tSKEW1 is the minimum time between the rising CLKA edge and a rising CLKB edge for FFB/IRB to transition HIGH in the next cycle. If the time between the rising edge of CLKA and rising
edge of CLKB is less than tSKEW1, then FFB/IRB may transition HIGH one CLKB cycle later than shown.
2. It is not necessary to program offset register bits on consecutive clock cycles. FIFO write attempts are ignored until FFA/IRA and FFB/IRB is set HIGH.
3. Programmable offsets are written serially to the SD input in the order AFA offset (Y1), AEB offset (X1), AFB offset (Y2), and AEA offset (X2).
Figure 6. Serial Programming of the Almost-Full Flag and Almost-Empty Flag Offset Values (IDT Standard and FWFT Modes)
19
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
FFA/IRA HIGH
t
ENH
ENH
t
ENS1
CSA
t
ENS1
t
W/RA
t
ENS2
t
ENH
ENH
MBA
ENA
tENS2
tENH
tENS2
tENS2
tENH
t
tDS
tDH
W1(1)
W2(1)
A0 - A35
No Operation
5608 drw09
NOTE:
1. Written to FIFO1.
Figure 7. Port A Write Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
tCLK
tCLKH
tCLKL
CLKB
FFB/IRB HIGH
tENH
tENS1
CSB
tENH
tENS1
W/RB
tENH
tENS2
MBB
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENB
tDH
t
DS
W1(1)
W2(1)
No Operation
B0-B35
5608 drw 10
NOTE:
1. Written to FIFO2.
DATA SIZE TABLE FOR LONG-WORD WRITES TO FIFO2
SIZE MODE(1)
SIZE
DATA WRITTEN TO FIFO2
DATA READ FROM FIFO2
BM
BE
B35-B27
B26-B18
B17-B9
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
L
X
X
A
B
C
D
A
B
C
D
NOTE:
1. BE is selected at Master Reset: BM and SIZE must be static throughout device operation.
Figure 8. Port B Long-Word Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
20
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
FFB/IRB HIGH
tENH
t
ENS1
ENS1
CSB
t
W/RB
t
ENH
t
ENH
t
ENS2
t
ENS2
ENS2
MBB
t
ENH
t
ENH
t
ENS2
t
ENB
tDH
tDS
B0-B17
5608 drw 11
DATA SIZE TABLE FOR WORD WRITES TO FIFO2
SIZE MODE(1)
WRITE NO.
DATA WRITTEN
TO FIFO2
DATA READ FROM FIFO2
BM
SIZE
BE
B17-B9
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
1
2
1
2
A
B
H
L
H
A
B
C
D
C
C
A
D
D
B
H
L
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 9. Port B Word Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
CLKB
FFB/IRB HIGH
tENH
t
ENS1
ENS1
CSB
t
W/RB
MBB
t
ENH
tENH
t
ENS2
ENS2
t
tENH
tENS2
tENH
ENB
tDS
tDH
B0-B8
5608 drw 12
DATA SIZE TABLE FOR BYTE WRITES TO FIFO2
SIZE MODE(1)
WRITE NO. DATA WRITTEN
TO FIFO2
DATA READ FROM FIFO2
BM
SIZE
BE
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
1
2
3
4
1
2
3
4
A
B
C
D
D
C
B
A
H
H
H
H
A
B
C
D
H
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 10. Port B Byte Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
21
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
EFB/ORB
HIGH
CSB
W/RB
MBB
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENB
t
MDV
No Operation
W2(1)
tDIS
t
A
t
A
t
EN
W1(1)
W2(1)
Previous Data
B0-B35
(Standard Mode)
t
MDV
tDIS
tA
t
A
OR
tEN
W3(1)
W1(1)
B0-B35
(FWFT Mode)
5608 drw 13
NOTE:
1. Read From FIFO1.
DATA SIZE TABLE FOR FIFO LONG-WORD READS FROM FIFO1
SIZE MODE(1)
SIZE
DATA WRITTEN TO FIFO1
DATA READ FROM FIFO1
BM
BE
A35-A27
A26-A18
A17-A9
A8-A0
B35-B27
B26-B18
B17-B9
B8-B0
L
X
X
A
B
C
D
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation .
Figure 11. Port B Long-Word Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
CLKB
HIGH
EFB/ORB
CSB
W/RB
MBB
ENB
t
ENS2
tENH
No Operation
Read 2
t
MDV
tDIS
t
A
tA
t
EN
B0-B17
Read 1
Read 2
Previous Data
(Standard Mode)
tDIS
t
MDV
OR
t
A
tA
t
EN
B0-B17
(FWFT Mode)
Read 3
Read 1
5608 drw 14
NOTE:
1. Unused word B18-B35 are indeterminate for word-size reads.
DATA SIZE TABLE FOR WORD READS FROM FIFO1
SIZE MODE(1)
SIZE
DATA WRITTEN TO FIFO1
READ NO.
DATA READ FROM FIFO1
BM
BE
A35-A27
A26-A18
A17-A9
A8-A0
B17-B9
B8-B0
H
L
L
H
A
B
C
D
1
2
1
2
A
C
C
A
B
D
D
B
H
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation .
Figure 12. Port-B Word Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
22
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
EFB/ORB HIGH
CSB
W/RB
MBB
tENS2
tENH
ENB
No Operation
t
DIS
DIS
t
MDV
t
A
t
A
t
A
t
A
t
EN
B0-B8
Read 1
Read 2
Previous Data
Read 3
Read 4
Read 5
(Standard Mode)
t
MDV
t
OR
t
A
tA
tA
t
A
t
EN
B0-B8
Read 1
Read 2
Read 3
Read 4
(FWFT Mode)
5608 drw 15
NOTE:
1. Unused bytes B9-B17, B18-B26, and B27-B35 are indeterminate for byte-size reads.
DATA SIZE TABLE FOR BYTE READS FROM FIFO1
SIZE MODE(1)
DATA WRITTEN TO FIFO1
READ NO.
DATA READ
FROM FIFO1
B8-B0
BM
SIZE
BE
A35-A27
A26-A18
A17-A9
A8-A0
1
2
3
4
1
2
3
4
A
B
C
D
D
C
B
A
H
H
H
H
A
B
C
D
D
H
L
A
B
C
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 13. Port-B Byte Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
tCLK
tCLKL
tCLKH
CLKA
EFA/ORA HIGH
CSA
W/RA
MBA
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENA
No Operation
W2(1)
t
MDV
t
DIS
DIS
t
A
t
A
t
EN
A0-A35
Previous Data
W1(1)
W2(1)
(Standard Mode)
t
MDV
t
tA
t
A
OR
t
EN
A0-A35
W3(1)
(1)
W1
(FWFT Mode)
5608 drw16
NOTE:
1. Read From FIFO2.
Figure 14. Port-A Read Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
23
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
CSA
LOW
WRA HIGH
t
ENS2
ENS2
t
ENH
MBA
t
t
ENH
ENA
IRA HIGH
tDS
tDH
A0-A35
W1
t
CLKtCLKL
(1)
tCLKH
tSKEW1
CLKB
ORB
1
2
3
t
REF
tREF
FIFO1 Empty
CSB LOW
W/RB HIGH
LOW
MBB
tENS2
tENH
ENB
tA
Old Data in FIFO1 Output Register
W1
B0-B35
5608 drw17
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for ORB to transition HIGH and to clock the next word to the FIFO1 output register in three CLKB cycles.
If the time between the rising CLKA edge and rising CLKB edge is less than tSKEW1, then the transition of ORB HIGH and load of the first word to the output register may occur one CLKB
cycle later than shown.
2. If Port B size is word or byte, ORB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 15. ORB Flag Timing and First Data Word Fall Through when FIFO1 is Empty (FWFT Mode)
24
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
t
CLK
t
CLKL
t
CLKH
CLKA
CSA
LOW
HIGH
WRA
t
ENS2
t
ENH
ENH
MBA
t
tENS2
ENA
FFA
HIGH
tDS
tDH
A0-A35
W1
t
CLK
(1)
SKEW1
t
CLKH
t
tCLKL
CLKB
1
2
t
REF
t
REF
FIFO1 Empty
LOW
EFB
CSB
W/RB HIGH
LOW
MBB
tENH
tENS2
ENB
tA
W1
B0-B35
5608 drw18
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for EFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then the transition of EFB HIGH may occur one CLKB cycle later than shown.
2. If Port B size is word or byte, EFB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 16. EFB Flag Timing and First Data Read Fall Through when FIFO1 is Empty (IDT Standard Mode)
25
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
CSB
LOW
LOW
W/RB
tENS2
tENH
MBB
ENB
tENH
tENS2
IRB
HIGH
tDH
tDS
B0-B35
W1
t
CLK
(1)
SKEW1
tCLKH
t
CLKL
t
1
2
CLKA
ORA
3
t
REF
tREF
FIFO2 Empty
CSA
LOW
LOW
W/RA
LOW
MBA
ENA
tENS2
tENH
tA
Old Data in FIFO2 Output Register
W1
A0-A35
5608 drw19
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for ORA to transition HIGH and to clock the next word to the FIFO2 output register in three CLKA cycles.
If the time between the CLKB edge and the rising CLKA edge is less than tSKEW1, then the transition of ORA HIGH and load of the first word to the output register may occur one CLKA
cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 17. ORA Flag Timing and First Data Word Fall through when FIFO2 is Empty (FWFT Mode)
26
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
t
CLK
t
CLKL
t
CLKH
CLKB
CSB LOW
LOW
W/RB
tENS2
tENH
MBB
ENB
tENS2
tENH
FFB HIGH
B0-B35
tDH
tDS
W1
(1)
t
CLK
tSKEW1
t
CLKH
t
CLKL
1
2
CLKA
t
REF
t
REF
EFA
FIFO2 Empty
LOW
LOW
LOW
CSA
W/RA
MBA
tENS2
tENH
ENA
tA
W1
A0-A35
5608 drw20
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for EFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW1, then the transition of EFA HIGH may occur one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 18. EFA Flag Timing and First Data Read when FIFO2 is Empty (IDT Standard Mode)
27
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
CSB
LOW
W/RB
HIGH
LOW
MBB
tENS2
tENH
ENB
ORB
HIGH
tA
Previous Word in FIFO1 Output Register
Next Word From FIFO1
B0-B35
(1)
tCLK
tSKEW1
tCLKH
tCLKL
1
2
CLKA
t
WFF
t
WFF
FIFO1 Full
LOW
IRA
CSA
HIGH
W/RA
tENH
tENS2
MBA
tENS2
tENH
ENA
tDS
tDH
Write
A0-A35
To FIFO1
5608 drw21
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for IRA to transition HIGH in the next CLKA cycle. If the time between the
rising CLKB edge and rising CLKA edge is less than tSKEW1, then IRA may transition HIGH one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that reads the last word or byte write of the long word, respectively.
Figure 19. IRA Flag Timing and First Available Write when FIFO1 is Full (FWFT Mode)
tCLK
tCLKH
tCLKL
CLKB
LOW
CSB
W/RB
MBB
HIGH
LOW
tENS2
tENH
ENB
HIGH
EFB
tA
Previous Word in FIFO1 Output Register
Next Word From FIFO1
B0-B35
(1)
t
CLK tCLKL
tSKEW1
tCLKH
CLKA
1
2
t
WFF
t
WFF
FFA
FIFO1 Full
CSA LOW
W/RA HIGH
t
ENH
t
ENS2
ENS2
MBA
t
tENH
ENA
tDH
tDS
Write
A0-A35
5608 drw22
To FIFO1
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for FFA to transition HIGH in the next CLKA cycle. If the time between the
rising CLKB edge and rising CLKA edge is less than tSKEW1, then FFA may transition HIGH one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced from the rising CLKB edge that reads the last word or byte of the long word, respectively.
Figure 20. FFA Flag Timing and First Available Write when FIFO1 is Full (IDT Standard Mode)
28
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
CSA
LOW
LOW
W/RA
LOW
MBA
tENS2
tENH
ENA
ORA
HIGH
tA
Previous Word in FIFO2 Output Register
SKEW1
Next Word From FIFO2
A0-A35
(1)
tCLK
t
tCLKH
tCLKL
1
2
CLKB
t
WFF
t
WFF
IRB
CSB
FIFO2 FULL
LOW
W/RB
LOW
tENS2
tENH
MBB
ENB
tENS2
tENH
tDS
tDH
Write
B0-B35
5608 drw23
To FIFO2
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for IRB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then IRB may transition HIGH one CLKB cycle later than shown.
2. If Port B size is word or byte, IRB is set LOW by the last word or byte write of the long word, respectively.
Figure 21. IRB Flag Timing and First Available Write when FIFO2 is Full (FWFT Mode)
29
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
LOW
LOW
LOW
CSA
W/RA
MBA
tENS2
tENH
ENA
EFA
HIGH
tA
Previous Word in FIFO2 Output Register
Next Word From FIFO2
A0-A35
(1)
tCLK
tSKEW1
tCLKH
tCLKL
CLKB
1
2
t
WFF
t
WFF
FIFO2 Full
LOW
FFB
CSB
LOW
W/RB
t
ENS2
ENS2
t
ENH
MBB
ENB
t
t
ENH
tDS
tDH
Write
B0-B35
5608 drw24
To FIFO2
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for FFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then FFB may transition HIGH one CLKB cycle later than shown.
2. If Port B size is word or byte, FFB is set LOW by the last word or byte write of the long word, respectively.
Figure 22. FFB Flag Timing and First Available Write when FIFO2 is Full (IDT Standard Mode)
30
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
tENS2
tENH
ENA
(1)
tSKEW2
1
2
CLKB
t
PAE
t
PAE
X1 Words in FIFO1
AEB
(X1+1) Words in FIFO1
ENS2
t
t
ENH
ENB
5608 drw 25
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AEB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW2, then AEB may transition HIGH one CLKB cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = LOW, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = HIGH, MBB = LOW). Data in the FIFO1 output register has been read from the FIFO.
3. If Port B size is word or byte, AEB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 23. Timing for AEB when FIFO1 is Almost-Empty (IDT Standard and FWFT Modes)
CLKB
tENS2
tENH
ENB
(1)
tSKEW2
1
2
CLKA
t
PAE
t
PAE
AEA
X2 Words in FIFO2
(X2+1) Words in FIFO2
ENS2
t
tENH
ENA
5608 drw 26
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AEA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW2, then AEA may transition HIGH one CLKA cycle later than shown.
2. FIFO2 Write (CSB = LOW, W/RB = LOW, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW). Data in the FIFO2 output register has been read from the FIFO.
3. If Port B size is word or byte, tSKEW2 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 24. Timing for AEA when FIFO2 is Almost-Empty (IDT Standard and FWFT Modes)
(1)
tSKEW2
1
2
CLKA
ENA
tENH
tENS2
t
PAF
t
PAF
(D-Y1) Words in FIFO1
[D-(Y1+1)] Words in FIFO1
AFA
CLKB
tENS2
tENH
ENB
5608 drw 27
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW2, then AFA may transition HIGH one CLKA cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = HIGH, MBB = LOW). Data in the FIFO1 output register has been read from the FIFO.
3. D = Maximum FIFO Depth = 2,048 for the IDT723654, 4,096 for the IDT723664, 8,192 for the IDT723674.
4. If Port B size is word or byte, tSKEW2 is referenced to the rising CLKB edge that reads the last word or byte of the long word, respectively.
Figure 25. Timing for AFA when FIFO1 is Almost-Full (IDT Standard and FWFT Modes)
31
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
(1)
tSKEW2
1
2
CLKB
ENB
tENH
tENS2
t
PAF
t
PAF
(D-Y2) Words in FIFO2
AFB
[D-(Y2+1)] Words in FIFO2
CLKA
tENH
tENS2
ENA
5608 drw 28
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW2, then AFB may transition HIGH one CLKB cycle later than shown.
2. FIFO2 write (CSB = LOW, W/RB = LOW, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW). Data in the FIFO2 output register has been read from the FIFO.
3. D = Maximum FIFO Depth = 2,048 for the IDT723654, 4,096 for the IDT723664, 8,192 for the IDT723674.
4. If Port B size is word or byte, AFB is set LOW by the last word or byte write of the long word, respectively.
Figure 26. Timing for AFB when FIFO2 is Almost-Full (IDT Standard and FWFT Modes)
CLKA
t
ENH
ENH
t
ENS1
CSA
t
t
ENS1
W/RA
tENH
tENS2
MBA
tENH
tENS2
ENA
tDH
tDS
W1
A0-A35
CLKB
t
PMF
t
PMF
MBF1
CSB
W/RB
MBB
ENB
tENH
tENS2
t
PMR
tEN
t
MDV
tDIS
FIFO1 Output Register
W1 (Remains valid in Mail1 Register after read)
B0-B35
5608 drw29
NOTE:
1. If Port B is configured for word size, data can be written to the Mail1 register using A0-A17 (A18-A35 are don't care inputs). In this first case B0-B17 will have valid data (B18-B35
will be indeterminate). If Port B is configured for byte size, data can be written to the Mail1 Register using A0-A8 (A9-A35 are don't care inputs). In this second case, B0-B8 will
have valid data (B9-B35 will be indeterminate).
Figure 27. Timing for Mail1 Register and MBF1 Flag (IDT Standard and FWFT Modes)
32
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
tENH
tENS1
CSB
W/RB
MBB
ENB
t
ENH
t
ENS1
t
ENH
t
ENS2
ENS2
t
t
ENH
t
DH
tDS
W1
B0-B35
CLKA
t
PMF
tPMF
MBF2
CSA
W/RA
MBA
ENA
tENH
tENS2
t
PMR
tEN
tDIS
t
MDV
A0-A35
W1 (Remains valid in Mail 2 Register after read)
FIFO2 Output Register
5608 drw30
NOTE:
1. If Port B is configured for word size, data can be written to the Mail2 Register using B0-B17 (B18-B35 are don’t care inputs). In this first case A0-A17 will have valid data
(A18-A35 will be indeterminate). If Port B is configured for byte size, data can be written to the Mail2 Register using B0-B8 (B9-B35 are don’t care inputs). In this second
case, A0-A8 will have valid data (A9-A35 will be indeterminate).
Figure 28. Timing for Mail2 Register and MBF2 Flag (IDT Standard and FWFT Modes)
33
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
4
1
2
3
2
3
4
1
tENS2
tENH
ENB
RT1
t
RSTS
t
RSTH
t
RTMH
t
RTMS
RTM
(2)
REF
(2)
REF
t
t
EFB
tA
B0-Bn
Wx
W1
5608 drw 31
NOTES:
1. CSB = LOW
2. Retransmit setup is complete after EFB returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO1.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO1 (Master or Partial) and Retransmit setup. Therefore, FFA will be LOW throughout the Retransmitsetup
procedure. D = 2,048, 4,096 and 8,192 for the IDT723654, IDT723664 and IDT723674 respectively.
Figure 29. Retransmit Timing for FIFO1 (IDT Standard Mode)
CLKB
CLKA
4
1
2
3
2
3
4
1
tENS2
tENH
ENA
RT2
t
RSTH
t
RSTS
t
RTMH
t
RTMS
RTM
(2)
REF
(2)
REF
t
t
EFA
tA
A0-An
Wx
W1
5608 drw 32
NOTES:
1. CSA = LOW
2. Retransmit setup is complete after EFA returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO2.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO2 (Master or Partial) and Retransmit setup. Therefore, FFB will be LOW throughout the Retransmit
setup procedure. D = 2,048, 4,096 and 8,192 for the IDT723654, IDT723664 and IDT723674 respectively.
Figure 30. Retransmit Timing for FIFO2 (IDT Standard Mode)
34
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
4
1
2
3
2
3
4
1
ENB LOW
t
RSTS
tRSTH
RT1
RTM
ORB
t
RTMH
t
RTMS
(2)
REF
(2)
REF
t
t
tA
B0-Bn
Wx
W1
5608 drw 33
NOTES:
1. CSB = LOW
2. Retransmit setup is complete after ORB returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO1.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO1 (Master or Partial) and Retransmit setup. Therefore, IRA will be LOW throughout the Retransmit
setup procedure. D = 2,049, 4,097 and 8,193 for the IDT723654, IDT723664 and IDT723674 respectively.
Figure 31. Retransmit Timing for FIFO1 (FWFT Mode)
CLKB
CLKA
4
1
2
3
2
3
4
1
LOW
ENA
RT2
tRSTH
t
RSTS
t
RTMH
t
RTMS
RTM
(2)
REF
(2)
REF
t
t
ORA
tA
A0-An
Wx
W1
5608 drw 34
NOTES:
1. CSA = LOW
2. Retransmit setup is complete after ORA returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO2 after Master Reset on FIFO2.
4. No more than D-2 may be written to the FIFO2 between Reset of FIFO2 (Master or Partial) and Retransmit setup. Therefore, IRB will be LOW throughout the Retransmit
setup procedure. D = 2,049, 4,097 and 8,193 for the IDT723654, IDT723664 and IDT723674 respectively.
Figure 32. Retransmit Timing for FIFO2 (FWFT Mode)
35
IDT723654/723664/723674CMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PARAMETER MEASUREMENT INFORMATION
5V
1.1KΩ
From Output
Under Test
30 pF (1)
680Ω
PROPAGATION DELAY
LOAD CIRCUIT
3 V
3 V
Timing
Input
1.5 V
High-Level
1.5 V
Input
GND
1.5 V
GND
3 V
t
S
th
tW
3 V
Data,
Enable
Input
1.5 V
1.5 V
Low-Level
1.5 V
1.5 V
GND
Input
GND
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PULSE DURATIONS
3 V
Output
Enable
1.5 V
1.5 V
t
PZL
GND
tPLZ
3 V
≈3 V
Input
1.5 V
1.5 V
1.5 V
Low-Level
Output
GND
V
OL
tPD
t
PZH
tPD
V
OH
V
OH
≈O V
In-Phase
Output
1.5 V
1.5 V
High-Level
Output
1.5 V
V
t
PHZ
OL
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
5608 drw35
NOTE:
1. Includes probe and jig capacitance.
Figure 33. Output Load and AC Test Conditions
36
ORDERINGINFORMATION
IDT
X
XX
X
X
XXXXXX
Device Type Power
Speed
Package
Process/
Temperature
Range
Commercial (0°C to +70°C)
BLANK
PF
Thin Quad Flat Pack (TQFP, PK128-1)
12
15
Clock Cycle Time (tCLK
)
Commercial Only
Speed in Nanoseconds
Low Power
L
723654
723664
723674
2,048 x 36 x 2 SyncBiFIFO
4,096 x 36 x 2 SyncBiFIFO
8,192 x 36 x 2 SyncBiFIFO
with Bus-Matching
with Bus-Matching
with Bus-Matching
5608 drw36
NOTE:
1. Industrial temperature range is available by special order.
DATASHEETDOCUMENTHISTORY
12/20/2000
02/09/2001
03/21/2001
08/01/2001
11/03/2003
pg. 13
pgs. 5 and 12.
pgs. 7 and 8.
pgs. 7, 9, 10 and 37.
pg. 1.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
for Tech Support:
408-360-1753
email:FIFOhelp@idt.com
www.idt.com
37
相关型号:
©2020 ICPDF网 联系我们和版权申明