IDT72V3664L15PF9 [IDT]
FIFO, 4KX36, 10ns, Synchronous, CMOS, PQFP128, TQFP-128;型号: | IDT72V3664L15PF9 |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | FIFO, 4KX36, 10ns, Synchronous, CMOS, PQFP128, TQFP-128 先进先出芯片 |
文件: | 总37页 (文件大小:409K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3.3 VOLT CMOS SyncBiFIFOTM WITH BUS-MATCHING
2,048 x 36 x 2
4,096 x 36 x 2
8,192 x 36 x 2
IDT72V3654
IDT72V3664
IDT72V3674
• Big- or Little-Endian format for word and byte bus sizes
• Retransmit Capability
• Master Reset clears data and configures FIFO, Partial Reset
clears data but retains configuration settings
• Mailbox bypass registers for each FIFO
• Free-running CLKA and CLKB may be asynchronous or coincident
(simultaneous reading and writing of data on a single clock edge
is permitted)
• Auto power down minimizes power dissipation
• Available in space saving 128-pin Thin Quad Flatpack (TQFP)
• Pin and functionally compatible version of the 5V operating
IDT723654/723664/723674
FEATURES
• Memory storage capacity:
IDT72V3654
IDT72V3664
IDT72V3674
–
–
–
2,048 x 36 x 2
4,096 x 36 x 2
8,192 x 36 x 2
• Clock frequencies up to 100 MHz (6.5ns access time)
• Two independent clocked FIFOs buffering data in opposite
directions
• Select IDT Standard timing (using EFA, EFB, FFA, and FFB flags
functions) or First Word Fall Through Timing (using ORA, ORB,
IRA, and IRB flag functions)
• Programmable Almost-Empty and Almost-Full flags; each has five
default offsets (8, 16, 64, 256 and 1,024 )
• Serial or parallel programming of partial flags
• Port B bus sizing of 36 bits (long word), 18 bits (word) and 9 bits
(byte)
• Pin compatible to the lower density parts, IDT72V3624/72V3634/
72V3644
• Industrial temperature range (–40°C to +85°C) is available
FUNCTIONAL BLOCK DIAGRAM
MBF1
Mail 1
Register
CLKA
Port-A
Control
Logic
CSA
W/RA
ENA
RAM ARRAY
2,048 x 36
4,096 x 36
8,192 x 36
36
36
MBA
36
FIFO1,
Mail1
Reset
Logic
MRS1
PRS1
Write
Pointer
Read
Pointer
36
Status Flag
Logic
EFB/ORB
AEB
FFA/IRA
AFA
FIFO1
FIFO2
FS2
FS0/SD
Programmable Flag
Offset Registers
Timing
Mode
FWFT
FS1/SEN
B0-B35
A0-A35
13
Status Flag
Logic
EFA/ORA
FFB/IRB
AFB
AEA
36
Read
Pointer
Write
Pointer
36
FIFO2,
Mail2
Reset
Logic
MRS2
PRS2
RT1
RTM
RT2
FIFO1 and
FIFO2
Retransmit
Logic
RAM ARRAY
2,048 x 36
4,096 x 36
8,192 x 36
36
36
CLKB
CSB
W/RB
ENB
MBB
BE
Port-B
Control
Logic
Mail 2
Register
BM
SIZE
MBF2
4664 drw01
IDTandtheIDTlogoaretrademarksofIntegratedDeviceTechnology,Inc. TheSyncFIFOisatrademarkofIntegratedDeviceTechnology,Inc.
NOVEMBER 2003
COMMERCIAL TEMPERATURE RANGE
1
2003 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.
DSC-4664/5
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
portSRAMFIFOsonboardeachchipbufferdatainoppositedirections. FIFO
dataonPortBcanbeinputandoutputin36-bit,18-bit,or9-bitformatswitha
choiceofBig-orLittle-Endianconfigurations.
These devices are a synchronous (clocked) FIFO, meaning each port
employsasynchronousinterface. Alldatatransfersthroughaportaregated
totheLOW-to-HIGHtransitionofaportclockbyenablesignals. Theclocksfor
each port are independent of one another and can be asynchronous or
DESCRIPTION
TheIDT72V3654/72V3664/72V3674arepinandfunctionallycompat-
ible versions of the IDT723654/723664/723674, designed to run off a 3.3V
supplyforexceptionallylow-powerconsumption. Thesedevicesaremono-
lithic, high-speed, low-power, CMOS bidirectional synchronous (clocked)
FIFOmemorywhichsupportsclockfrequenciesupto100MHzandhasread
accesstimesasfastas6.5ns. Twoindependent2,048/4,096/8,192 x 36dual-
PIN CONFIGURATION
INDEX
W/RA
ENA
CLKA
3
GND
A35
5
A34
A33
7
A32
Vcc
A31
A30
GND
A29
A28
A27
A26
A25
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
CLKB
PRS2/RT2
Vcc
1
2
B35
B34
B33
B32
RTM
GND
B31
B30
B29
B28
B27
B26
Vcc
4
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
B25
B24
BM
A24
A23
BE/FWFT
GND
A22
GND
B23
B22
B21
B20
B19
B18
GND
B17
B16
SIZE
Vcc
B15
B14
B13
B12
GND
B11
B10
Vcc
A21
A20
A19
A18
GND
A17
A16
A15
A14
A13
Vcc
A12
GND
A11
A10
4664 drw 02
TQFP (PK128-1, order code: PF)
TOP VIEW
2
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
coincident. The enables for each port are arranged to provide a simple outputs,noreadoperationisrequired(Nevertheless,accessingsubsequent
bidirectionalinterfacebetweenmicroprocessorsand/orbuseswithsynchro- wordsdoesnecessitateaformalreadrequest).ThestateoftheBE/FWFTpin
nouscontrol.
CommunicationbetweeneachportmaybypasstheFIFOsviatwomailbox
duringFIFOoperationdetermines themodeinuse.
EachFIFOhas acombinedEmpty/OutputReadyFlag(EFA/ORAand
registers.Themailboxregisters’widthmatchestheselectedPortBbuswidth. EFB/ORB) and a combined Full/Input Ready Flag (FFA/IRA and FFB/
EachMailboxregisterhas a flag(MBF1 andMBF2)tosignalwhennewmail IRB). The EF and FF functions are selected in the IDT Standard mode. EF
has beenstored.
indicates whether or not the FIFO memory is empty. FF shows whether the
TwokindsofresetareavailableontheseFIFOs:MasterResetandPartial memoryisfullornot.TheIRandORfunctionsareselectedintheFirstWord
Reset. MasterResetinitializesthereadandwritepointerstothefirstlocation FallThroughmode.IRindicateswhetherornottheFIFOhasavailablememory
of the memory array, configures the FIFO for Big- or Little-Endian byte locations.ORshowswhethertheFIFOhasdataavailableforreadingornot.
arrangementandselectsserialflagprogramming,parallelflagprogramming, Itmarksthepresenceofvaliddataontheoutputs.
oroneoffivepossibledefaultflagoffsetsettings,8,16,64,256or1,024.There
are two Master Reset pins, MRS1 and MRS2.
Each FIFO has a programmable Almost-Empty flag (AEA and AEB)
and a programmable Almost-Full flag (AFA and AFB). AEA and AEB
PartialResetalsosetsthereadandwritepointerstothefirstlocationofthe indicatewhenaselectednumberofwordsremainintheFIFOmemory.AFA
memory.UnlikeMasterReset,anysettingsexistingpriortoPartialReset(i.e., and AFB indicate when the FIFO contains more than a selected number of
programmingmethodandpartialflagdefaultoffsets)areretained.PartialReset words.
is useful since it permits flushing of the FIFO memory without changing any
configurationsettings.EachFIFOhasitsown,independentPartialResetpin, port clock that writes data into its array. EFA/ORA, EFB/ORB, AEA and
PRS1 and PRS2. AEBaretwo-stagesynchronizedtotheportclockthatreadsdatafromitsarray.
FFA/IRA, FFB/IRB, AFA and AFB are two-stage synchronized to the
BothFIFO'shaveRetramsmitcapability,whenaRetransmitisperformed Programmable offsets for AEA, AEB, AFA and AFB are loaded in parallel
onarespectiveFIFOonlythereadpointerisresettothefirstmemorylocation. usingPortAorinserialvia the SDinput. Five defaultoffsetsettings are also
ARetransmitisperformedbyusingtheRetransmitMode,RTMpininconjunction provided. The AEA and AEB threshold can be set at 8, 16, 64, 256 or 1,024
withtheRetransmitpinsRT1orRT2,foreachrespectiveFIFO.Notethatthe locations from the empty boundary and the AFA and AFB threshold can be
two Retransmit pins RT1 and RT2 are muxed with the Partial Reset pins.
Thesedeviceshavetwomodesofoperation:IntheIDTStandardmode, are made using the FS0, FS1 and FS2 inputs during Master Reset.
thefirstwordwrittentoanemptyFIFOisdepositedintothememoryarray. A Interspersed Parity can also be selected during a Master Reset of the
setat8,16,64,256or1,024locationsfromthefullboundary.Allthesechoices
read operation is required to access that word (along with all other words FIFO.IfInterspersedParityisselectedthenduringparallelprogrammingofthe
residing in memory). In the First Word Fall Through mode (FWFT), the first flagoffsetvalues,thedevicewillignoredatalineA8.IfNon-InterspersedParity
wordwrittentoanemptyFIFOappearsautomaticallyontheoutputs,noread is selectedthendatalineA8willbecomeavalidbit.
operationrequired(Nevertheless,accessingsubsequentwordsdoesneces-
sitate a formal read request). The state of the BE/FWFT pin during Master If, at any time, the FIFO is not actively performing a function, the chip will
Resetdeterminesthemodeinuse. automatically power down. During the power down state, supply current
Twoormoredevicesmaybeusedinparalleltocreatewiderdatapaths.
Thesedeviceshavetwomodesofoperation:IntheIDTStandardmode, consumption(ICC)isataminimum.Initiatinganyoperation(byactivatingcontrol
thefirstwordwrittentoanemptyFIFOis depositedintothememoryarray.A inputs)willimmediatelytakethedeviceoutofthepowerdownstate.
read operation is required to access that word (along with all other words
TheIDT72V3654/72V3664/72V3674arecharacterizedforoperationfrom
residinginmemory).IntheFirstWordFallThroughmode(FWFT),thefirstlong- 0°Cto70°C.Industrialtemperaturerange(-40°Cto+85°C)isavailable.They
word (36-bit wide) written to an empty FIFO appears automatically on the arefabricatedusingIDT’shighspeed,submicronCMOStechnology.
3
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS
Symbol
A0-A35
AEA
Name
I/O
I/O
O
Description
PortAData
36-bitbidirectionaldataportforsideA.
PortAAlmost-
EmptyFlag
ProgrammableAlmost-EmptyflagsynchronizedtoCLKA.ItisLOWwhenthenumberofwordsin
FIFO2islessthanorequaltothevalueintheAlmost-EmptyAOffsetregister,X2.
AEB
PortBAlmost-
EmptyFlag
O
O
O
ProgrammableAlmost-EmptyflagsynchronizedtoCLKB.ItisLOWwhenthenumberofwordsin
FIFO1islessthanorequaltothevalueintheAlmost-EmptyBOffsetregister,X1.
AFA
PortAAlmost-
Full Flag
ProgrammableAlmost-FullflagsynchronizedtoCLKA.ItisLOWwhenthenumberofempty
locationsinFIFO1islessthanorequaltothevalueintheAlmost-FullAOffsetregister,Y1.
AFB
PortBAlmost-
Full Flag
ProgrammableAlmost-FullflagsynchronizedtoCLKB.ItisLOWwhenthenumberofempty
locations inFIFO2is less thanorequaltothevalueintheAlmost-FullBOffsetregister,Y2.
B0-B35
PortAData
I/O
I
36-bitbidirectionaldataportforsideB.
BE/FWFT Big-Endian/
FirstWord
This is a dual purpose pin. During Master Reset, a HIGH on BE will select Big Endian operation.
Inthis case, dependingonthe bus size, the mostsignificantbyte orwordonPortAis readfrom
PortBfirst (A-to-Bdata flow)orwrittentoPortBfirst(B-to-Adata flow). ALOWonBEwillselect
Little-Endianoperation. Inthis case,theleastsignificantbyteorwordonPortAis readfromPortB
first(forA-to-Bdataflow)orwrittentoPortBfirst(B-to-Adata flow). After Master Reset, this pin
selects the timing mode. A HIGH on FWFT selects IDT Standard mode, a LOW selects First Word
FallThroughmode.Oncethetimingmodehas beenselected,thelevelonFWFTmustbestatic
throughoutdeviceoperation.
Fall Through
Select
(1)
BM
Bus-MatchSelect
(Port B)
I
I
I
A HIGH on this pin enables either byte or word bus width on Port B, depending on the state of
SIZE. A LOW selects long word operation. BM works with SIZE and BE to select the bus size and
endianarrangementforPortB.ThelevelofBMmustbestaticthroughoutdeviceoperation.
CLKA
CLKB
PortAClock
PortBClock
CLKAis acontinuous clockthatsynchronizes alldatatransfers throughPortAandcanbe
asynchronous or coincident to CLKB. FFA/IRA, EFA/ORA, AFA, and AEA are allsynchronized
totheLOW-to-HIGHtransitionofCLKA.
CLKBis acontinuous clockthatsynchronizes alldatatransfers throughPortBandcanbe
asynchronous orcoincidenttoCLKA. FFB/IRB, EFB/ORB, AFB, andAEB are synchronizedto
theLOW-to-HIGHtransitionofCLKB.
CSA
CSB
PortAChipSelect
PortBChipSelect
I
I
CSA mustbeLOWtoenabletoLOW-to-HIGHtransitionofCLKAtoreadorwriteonPortA.
The A0-A35outputs are inthe high-impedance state when CSAis HIGH.
CSB mustbe LOWtoenable a LOW-to-HIGHtransitionofCLKBtoreadorwrite data onPortB.
The B0-B35outputs are inthe high-impedance state when CSBis HIGH.
EFA/ORA PortAEmpty/
OutputReadyFlag
O
This is a dualfunctionpin. Inthe IDTStandardmode, the EFA functionis selected. EFA
indicates whetherornotthe FIFO2memoryis empty. Inthe FWFTmode, the ORAfunctionis
selected. ORAindicates thepresenceofvaliddataonA0-A35outputs,availableforreading.
EFA/ORAissynchronizedtotheLOW-to-HIGHtransitionofCLKA.
EFB/ORB PortBEmpty/
OutputReadyFlag
O
This is adualfunctionpin.IntheIDTStandardmode,theEFBfunctionis selected. EFBindicates
whetherornotthe FIFO1memoryis empty. Inthe FWFTmode, the ORBfunctionis selected. ORB
indicates thepresenceofvaliddataontheB0-B35outputs,availableforreading. EFB/ORBis
synchronizedtotheLOW-to-HIGHtransitionofCLKB.
ENA
PortAEnable
I
I
ENAmustbe HIGHtoenable a LOW-to-HIGHtransitionofCLKAtoreadorwrite data onPortA.
ENBmustbe HIGHtoenable a LOW-to-HIGHtransitionofCLKBtoreadorwrite data onPortB.
ENB
PortBEnable
FFA/IRA
PortAFull/
Input Ready Flag
O
This is a dualfunctionpin. Inthe IDTStandardmode, the FFA functionis selected. FFA indicates
whetherornotthe FIFO1memoryis full. Inthe FWFTmode, the IRAfunctionis selected. IRA
indicates whetherornotthere is space available forwritingtothe FIFO1memory. FFA/IRAis
synchronizedtotheLOW-to-HIGHtransitionofCLKA.
FFB/IRB
PortBFull/
Input Ready Flag
O
This is adualfunctionpin.IntheIDTStandardmode,the FFB functionis selected. FFB indicates
whether or not the FIFO2 memory is full. In the FWFT mode, the IRB function is selected. IRB
indicates whether or not there is space available for writing to the FIFO2 memory. FFB/IRB is
synchronized to the LOW-to-HIGH transition of CLKB.
4
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS(CONTINUED)
Symbol
Name
I/O
Description
FS0/SD
FlagOffsetSelect0/
SerialData
I
FS1/SENandFS0/SDaredual-purposeinputs usedforflagoffsetregisterprogramming. During
MasterReset,FS1/SENandFS0/SD,togetherwithFS2,selecttheflagoffsetprogrammingmethod
Threeoffsetregisterprogrammingmethodsareavailable:automaticallyloadoneoffivepresetvalues
(8, 16, 64, 256 or 1,024), parallel load from Port A, and serial load.
FS1/SEN
FlagOffsetSelect1/
SerialEnable,
I
I
Whenserialloadisselectedforflagoffsetregisterprogramming,FS1/SENisusedasanenable
synchronous totheLOW-to-HIGHtransitionofCLKA.WhenFS1/SENis LOW,arisingedgeonCLKA
load the bit present on FS0/SD into the X and Y registers. The number of bit writes required to program
the offset registers is 44 for the IDT72V3654, 48 for the IDT72V3664, and 52 for the IDT72V3674.
The firstbitwrite stores the Y-register(Y1)MSBandthe lastbitwrite stores the X-register(X2)LSB.
FS2(1)
FlagOffsetSelect2
MBA
MBB
MBF1
Port A Mailbox
Select
I
I
A HIGH level on MBA chooses a mailbox register for a Port A read or write operation. When
theA0-A35outputsareactive,aHIGHlevelonMBAselectsdatafromthemail2registerforoutput
andaLOWlevelselectsFIFO2outputregisterdataforoutput.
Port B Mailbox
Select
A HIGH level on MBB chooses a mailbox register for a Port B read or write operation. When the
B0-B35outputs areactive,aHIGHlevelonMBBselects datafromthemail1registerforoutputand
aLOWlevelselectsFIFO1outputregisterdataforoutput.
Mail1Register
Flag
O
MBF1 is set LOW by a LOW-to-HIGH transition of CLKA that writes data to the mail1 register.
Writes tothe mail1registerare inhibitedwhile MBF1 is LOW. MBF1 is setHIGHbya LOW-to-HIGH
transition of CLKB when a Port B read is selected and MBB is HIGH. MBF1 is set HIGH following either
a MasterorPartialResetofFIFO1.
MBF2
MRS1
Mail2Register
Flag
O
I
MBF2issetLOWbyaLOW-to-HIGHtransitionofCLKBthatwritesdatatothemail2register.Writes
tothe mail2registerare inhibitedwhile MBF2is LOW. MBF2 is setHIGHbya LOW-to-HIGH
transition of CLKA when a Port A read is selected and MBA is HIGH. MBF2 is set HIGH following
eithera MasterorPartialResetofFIFO2.
FIFO1Master
Reset
ALOWonthis pin initializes the FIFO1readandwrite pointers tothe firstlocationofmemoryand sets the
Port B output register to all zeroes. A LOW-to-HIGH transition on MRS1 selects the programming
method(serialorparallel)andoneoffiveprogrammableflagdefaultoffsets forFIFO1andFIFO2.It
also configures PortBforbus size andendianarrangement. FourLOW-to-HIGHtransitions ofCLKA
andfourLOW-to-HIGHtransitionsofCLKBmustoccurwhileMRS1isLOW.
MRS2
FIFO2Master
Reset
I
I
ALOWonthispininitializestheFIFO2readandwritepointerstothefirstlocationofmemoryandsets
thePortAoutputregistertoallzeroes.ALOW-to-HIGHtransitiononMRS2,toggledsimultaneouslywith
MRS1,selectstheprogrammingmethod(serialorparallel)andoneoftheprogrammableflagdefault
offsets for FIFO2. Four LOW-to-HIGH transitions of CLKA and four LOW-to-HIGH transitions of CLKB
mustoccurwhileMRS2isLOW.
PRS1/
RT1
PartialReset/
RetransmitFIFO1
This pinis muxedforbothPartialReset andRetransmitoperations,itis usedinconjunctionwiththeRTM
pin. IfRTMis ina LOWcondition, a LOWonthis pinperforms a PartialResetonFIFO1andinitializes
theFIFO1readandwritepointerstothefirstlocationofmemoryandsetsthePortBoutputregisterto
allzeroes.DuringPartialReset,thecurrentlyselectedbussize,endianarrangement,programming
method(serialorparallel), andprogrammable flagsettings are allretained. IfRTMis HIGH, a LOWon
thispinperformsaRetransmitandinitializestheFIFO1readpointeronlytothefirstmemorylocation.
PRS2/
RT2
PartialReset/
RetransmitFIFO2
I
This pinis muxedforbothPartialReset andRetransmitoperations,itis usedinconjunctionwiththeRTM
pin. IfRTMis ina LOWcondition, a LOWonthis pinperforms a PartialResetonFIFO2andinitializes
theFIFO2readandwriteselectedbus size,endianarrangement,programmingmethod(serialor
parallel),andprogrammableflagsettings areallretained.IfRTMis HIGH,aLOWonthis pinperforms
aRetransmitandinitializestheFIFO2readpointeronlytothefirstmemorylocation.
RTM
RetransmitMode
BusSizeSelect
I
I
This pinis usedinconjunctionwiththe RT1 andRT2 pins. WhenRTMis HIGHa Retransmitis performed
on FIFO1 or FIFO2 respectively.
(1)
SIZE
A HIGH on this pin when BM is HIGH selects byte bus (9-bit) size on Port B. A LOW on this pin when
BM is HIGH selects word (18-bit) bus size. SIZE works with BM and BE to select the bus size and endian
arrangementforPortB.ThelevelofSIZEmustbestaticthroughoutdeviceoperation
NOTE:
1. FS2, BM and SIZE inputs are not TTL compatible. These inputs should be tied to GND or VCC.
5
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PINDESCRIPTIONS(CONTINUED)
Symbol
Name
I/O
Description
W/RA
Port-AWrite/
ReadSelect
I
A HIGHselects a write operationanda LOWselects a readoperationonPortAfora LOW-to-HIGH
transitionofCLKA.TheA0-A35outputs areintheHIGHimpedancestatewhenW/RAis HIGH.
W/RB
Port-BWrite/
ReadSelect
I
A LOWselects a write operationanda HIGHselects a readoperationonPortBfora LOW-to-HIGH
transitionofCLKB.TheB0-B35outputsareintheHIGHimpedancestatewhenW/RBisLOW.
6
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR
TEMPERATURE RANGE (Unless otherwise noted)(1)
Symbol
Rating
Commercial
–0.5to+4.6
–0.5 to VCC+0.5
–0.5 to VCC+0.5
±20
Unit
V
VCC
SupplyVoltageRange
InputVoltageRange
OutputVoltageRange
(2)
VI
V
(2)
VO
V
IIK
Input Clamp Current (VI < 0 or VI > VCC)
Output Clamp Current (VO = < 0 or VO > VCC)
Continuous Output Current (VO = 0 to VCC)
Continuous Current Through VCC or GND
StorageTemperatureRange
mA
mA
mA
mA
°C
IOK
±50
IOUT
ICC
±50
±400
TSTG
–65 to 150
NOTES:
1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these
or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect
device reliability.
2. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed.
RECOMMENDEDOPERATINGCONDITIONS
Symbol
Parameter
SupplyVoltagefor10ns
SupplyVoltagefor15ns
High-LevelInputVoltage
Low-LevelInputVoltage
High-LevelOutputCurrent
Low-LevelOutputCurrent
OperatingTemperature
Min.
3.15
3.0
2
Typ.
3.3
3.3
—
Max.
3.45
3.6
Unit
V
(1)
VCC
VCC
VIH
VIL
IOH
IOL
TA
V
VCC+0.5
0.8
V
—
—
—
0
—
V
—
–4
mA
mA
°C
—
8
—
70
NOTE:
1. For 10ns speed grade: Vcc = 3.3V ± 0.15V, JEDEC JESD8-A compliant
ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING FREE-
AIR TEMPERATURE RANGE (Unless otherwise noted)
IDT72V3654
IDT72V3664
IDT72V3674
Commercial
tCLK = 10, 15 ns(2)
Symbol
VOH
VOL
Parameter
OutputLogic"1"Voltage
OutputLogic"0"Voltage
InputLeakageCurrent(AnyInput)
OutputLeakageCurrent
Test Conditions
IOH = –4 mA
Min.
2.4
—
—
—
—
—
—
—
Typ.(1)
—
—
—
—
—
—
4
Max.
—
0.5
±10
±10
5
Unit
V
VCC = 3.0V,
VCC = 3.0V,
VCC = 3.6V,
VCC = 3.6V,
IOL = 8 mA
V
ILI
VI = VCC or 0
µ A
µ A
mA
mA
pF
ILO
VO = VCC or 0
VI = VCC –0.2V or 0V
VI = VCC –0.2V or 0V
f = 1 MHz
ICC2(3)
ICC3(3)
Standby Current (with CLKA & CLKB running) VCC = 3.6V,
StandbyCurrent(noclocksrunning)
InputCapacitance
VCC = 3.6V,
VI = 0,
1
(4)
CIN
—
—
(4)
COUT
OutputCapacitance
VO = 0,
f = 1 MHZ
8
pF
NOTES:
1. All typical values are at VCC = 3.3V, TA = 25°C.
2. Commercial-10ns speed grade only: Vcc = 3.3V ± 0.15V, TA = 0° to +70°; JEDEC JESD8-A compliant.
3. For additional ICC information, see Figure 1, Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS).
4. Characterized values, not currently tested.
7
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
DETERMINING ACTIVE CURRENT CONSUMPTION AND POWER DISSIPATION
TheICC(f)currentforthegraphinFigure1wastakenwhilesimultaneouslyreadingandwritingaFIFOontheIDT72V3654/72V3664/72V3674withCLKA
andCLKBsettofS. Alldatainputsanddataoutputschangestateduringeachclockcycletoconsumethehighestsupplycurrent. Dataoutputsweredisconnected
tonormalizethegraphtoazerocapacitanceload. Oncethecapacitanceloadperdata-outputchannelandthenumberofthesedevice'sinputsdrivenbyTTL
HIGHlevels areknown,thepowerdissipationcanbecalculatedwiththeequationbelow.
CALCULATING POWER DISSIPATION
WithICC(f) takenfromFigure1,themaximumpowerdissipation(PT)oftheseFIFOs maybecalculatedby:
2
PT = VCC x ICC(f) + Σ(CL x VCC x fo)
N
where:
N
CL
fo
=
=
=
number of used outputs (36-bit (long word), 18-bit (word) or 9-bit (byte) bus size)
output capacitance load
switchingfrequencyofanoutput
100
90
VCC = 3.6V
80
70
60
VCC = 3.0V
VCC = 3.3V
fdata = 1/2 fS
TA
= 25°C
CL
= 0 pF
50
40
30
20
10
0
100
0
10
20
30
40
50
Clock Frequency MHz
60
70
90
80
4664 drw03
fS
Figure 1. Typical Characteristics: Supply Current (ICC) vs. Clock Frequency (fS)
8
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
TIMING REQUIREMENTS OVER RECOMMENDED RANGES OF SUPPLY
VOLTAGE AND OPERATING FREE-AIR TEMPERATURE
(For 10ns speed grade only: Vcc = 3.3V ± 0.15V; TA = 0°C to +70° C;JEDEC JESD8-A compliant)
IDT72V3654L10(1)
IDT72V3664L10(1)
IDT72V3674L10(1)
IDT72V3654L15
IDT72V3664L15
IDT72V3674L15
Symbol
fS
Parameter
Min.
—
10
4.5
4.5
3
Max.
100
—
Min.
—
15
6
Max.
Unit
MHz
ns
Clock Frequency, CLKA or CLKB
66.7
—
tCLK
tCLKH
tCLKL
tDS
Clock Cycle Time, CLKA or CLKB
Pulse Duration, CLKA or CLKB HIGH
PulseDuration, CLKAandCLKBLOW
SetupTime, A0-A35before CLKA↑andB0-B35before CLKB↑
—
—
ns
—
6
—
ns
—
4
—
ns
tENS1
SetupTime,CSA andW/RAbefore CLKA↑;CSB and
W/RBbeforeCLKB↑
4
—
4.5
—
ns
tENS2
tRSTS
Setup Time, ENA, and MBA before CLKA↑; ENB, and
MBBbeforeCLKB↑
3
5
—
—
4.5
5
—
—
ns
ns
Setup Time, MRS1, MRS2, PRS1, or PRS2 LOW before
(2)
CLKA↑orCLKB↑
tFSS
tBES
tSDS
Setup Time, FS0, FS1, FS2 before MRS1 and MRS2 HIGH
SetupTime, BE/FWFT beforeMRS1 andMRS2HIGH
SetupTime,FS0/SDbeforeCLKA↑
7.5
7.5
3
—
—
—
—
—
—
—
—
7.5
7.5
4
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
tSENS
tFWS
tRTMS
tDH
SetupTime,FS1/SENbeforeCLKA↑
3
4
SetupTime,BE/FWFTbeforeCLKA↑
0
0
Setup Time, RTM before RT1; RTM before RT2
HoldTime,A0-A35afterCLKA↑andB0-B35afterCLKB↑
5
5
0.5
0.5
1
tENH
HoldTime, CSA, W/RA, ENA, andMBAafterCLKA↑;CSB,
W/RB, ENB, andMBBafterCLKB↑
1
tRSTH
Hold Time, MRS1, MRS2, PRS1 orPRS2 LOW after CLKA↑
4
—
4
—
ns
(2)
orCLKB↑
tFSH
Hold Time, FS0, FS1, FS2 after MRS1 and MRS2 HIGH
Hold Time, BE/FWFT after MRS1 and MRS2 HIGH
HoldTime, FS0/SDafterCLKA↑
2
2
—
—
—
—
—
—
—
2
2
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
tBEH
tSDH
0.5
0.5
2
1
tSENH
tSPH
HoldTime,FS1/SENHIGHafterCLKA↑
1
Hold Time, FS1/SEN HIGH after MRS1 and MRS2 HIGH
HoldTime, RTMafterRT1;RTMafterRT2
2
tRTMH
tSKEW1(3)
5
5
SkewTimebetweenCLKA↑andCLKB↑forEFA/ORA,
EFB/ORB, FFA/IRA, and FFB/IRB
5
7.5
tSKEW2(3,4) SkewTime betweenCLKA↑andCLKB↑ forAEA,AEB, AFA,
12
—
12
—
ns
and AFB
NOTES:
1. For 10ns speed grade: Vcc = 3.3V ± 0.15V; TA = 0° to +70°.
2. Requirement to count the clock edge as one of at least four needed to reset a FIFO.
3. Skew time is not a timing constraint for proper device operation and is only included to illustrate the timing relationship between CLKA cycle and CLKB cycle.
4. Design simulated, not tested.
9
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
SWITCHING CHARACTERISTICS OVER RECOMMENDED RANGES OF SUPPLY
VOLTAGE AND OPERATING FREE-AIR TEMPERATURE, CL = 30pF
(For 10ns speed grade only: Vcc = 3.3V ± 0.15V; TA = 0ο C to +70ο C;JEDEC JESD8-A compliant)
IDT72V3654L10(1)
IDT72V3664L10(1)
IDT72V3674L10(1)
IDT72V3654L15
IDT72V3664L15
IDT72V3674L15
Symbol
tA
Parameter
Min.
2
Max.
Min.
2
Max.
Unit
ns
Access Time,CLKA↑toA0-A35andCLKB↑toB0-B35
6.5
6.5
10
8
tWFF
PropagationDelayTime, CLKA↑ toFFA/IRAandCLKB↑
toFFB/IRB
2
2
ns
tREF
tPAE
tPAF
tPMF
tPMR
tMDV
tRSF
PropagationDelayTime,CLKA↑toEFA/ORAandCLKB↑
toEFB/ORB
1
1
1
0
3
3
1
6.5
6.5
6.5
6.5
8
1
1
1
0
2
2
1
8
8
ns
ns
ns
ns
ns
ns
ns
PropagationDelayTime,CLKA↑toAEAandCLKB↑to
AEB
PropagationDelayTime,CLKA↑toAFAandCLKB↑to
AFB
8
Propagation Delay Time, CLKA↑ toMBF1 LOW or MBF2
HIGH and CLKB↑ to MBF2 LOW or MBF1 HIGH
8
PropagationDelayTime, CLKA↑toB0-B35(2)andCLKB↑
10
10
15
toA0-A35(3)
Propagation Delay Time, MBA to A0-A35 valid and MBB to
B0-B35 valid
6.5
10
Propagation Delay Time, MRS1 or PRS1 LOW to AEB
LOW, AFA HIGH, and MBF1 HIGH and MRS2 or PRS2
LOW to AEA LOW, AFB HIGH, and MBF2 HIGH
tEN
tDIS
Enable Time, CSA orW/RALOWtoA0-A35Active and
CSB LOW and W/RB HIGH to B0-B35 Active
2
1
6
6
2
1
10
8
ns
ns
Disable Time, CSA or W/RA HIGH to A0-A35 at high
impedance and CSB HIGH or W/RB LOW to B0-B35 at
highimpedance
NOTES:
1. For 10ns speed grade: Vcc = 3.3V ± 0.15V; TA = 0° to +70°.
2. Writing data to the mail1 register when the B0-B35 outputs are active and MBB is HIGH.
3. Writing data to the mail2 register when the A0-A35 outputs are active and MBA is HIGH.
10
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
and four Port B Clock (CLKB) LOW-to-HIGH transitions. The Retransmit
initializesthereadpointerofFIFO1tothefirstmemorylocation.
The FIFO2 memory undergoes a Retransmit by taking its associated
Retransmit(RT2)inputLOWforatleastfourPortAClock(CLKA)andfourPort
CClock(CLKC)LOW-to-HIGHtransitions.TheRetransmitinitializestheread
pointerofFIFO2tothefirstmemorylocation.
The RTM pin must be HIGH during the time of Retranmit. Note that the
RT1inputismuxedwiththePRS1input,thestateoftheRTMpindetermining
whetherthispinperformsaRetransmitorPartialReset.Also,theRT2inputis
muxedwiththePRS2input,thestateoftheRTMpindeterminingwhetherthis
pinperformsaRetransmitorPartialReset.
SIGNALDESCRIPTION
MASTER RESET (MRS1, MRS2)
Afterpowerup,aMasterReset operationmustbeperformedbyproviding
a LOW pulse to MRS1 and MRS2 simultaneously. Afterwards, each of the
two FIFO memories of the IDT72V3654/72V3664/72V3674 undergoes a
complete reset by taking its associated Master Reset (MRS1, MRS2) input
LOWforatleastfourPortAClock(CLKA)andfourPortBClock(CLKB)LOW-
to-HIGHtransitions. TheMasterResetinputscanswitchasynchronouslyto
theclocks.AMasterReset initializestheassociatedwriteandreadpointersto
thefirstlocationofthememoryandforcestheFull/InputReadyflag(FFA/IRA,
FFB/IRB)LOW,theEmpty/OutputReadyflag(EFA/ORA,EFB/ORB)LOW,
the Almost-Empty flag (AEA, AEB) LOW and forces the Almost-Full flag
(AFA, AFB)HIGH. AMasterResetalsoforces theassociatedMailboxFlag
(MBF1, MFB2)ofthe parallelmailboxregisterHIGH. Aftera MasterReset,
theFIFO'sFull/InputReadyflagissetHIGHaftertwowriteclockcycles. Then
the FIFO is ready to be written to.
BIG-ENDIAN/FIRST WORD FALL THROUGH (BE/FWFT)
— ENDIAN SELECTION
Thisisadualpurposepin.AtthetimeofMasterReset,theBEselectfunction
isactive,permittingachoiceofBigorLittle-Endianbytearrangementfordata
writtentoorreadfromPortB.This selectiondetermines theorderbywhich
bytes (orwords)ofdata are transferredthroughthis port. Forthe following
illustrations,assumethatabyte(orword)bussizehasbeenselectedforPort
B.(NotethatwhenPortBis configuredforalongwordsize,theBig-Endian
A LOW-to-HIGH transition on the FIFO1 Master Reset (MRS1) input
latches the values ofthe Big-Endian(BE)inputfordeterminingthe orderby
whichbytes are transferredthroughPortB. Italso latches the values ofthe
FlagSelect(FS0,FS1andFS2)inputsforchoosingtheAlmost-FullandAlmost-
Emptyoffsetprogrammingmethod.
1
functionhas noapplicationandthe BEinputis a “don’tcare” .)
AHIGHonthe BE/FWFTinputwhenthe MasterReset(MRS1, MRS2)
inputsgofromLOWtoHIGHwillselectaBig-Endianarrangement.Whendata
ismovinginthedirectionfromPortAtoPortB,themostsignificantbyte(word)
ofthelongwordwrittentoPortAwillbereadfromPortBfirst;theleastsignificant
byte(word)ofthelongwordwrittentoPortAwillbereadfromPortBlast.When
data is movinginthe directionfromPortBtoPortA, the byte (word)written
toPortBfirstwillbereadfromPortAasthemostsignificantbyte(word)ofthe
long word; the byte (word) written to Port B last will be read from Port A as
theleastsignificantbyte(word)ofthelongword.
A LOW-to-HIGH transition on the FIFO2 Master Reset (MRS2) clears
theFlagOffsetRegistersofFIFO2(X2,Y2). ALOW-to-HIGHtransitiononthe
FIFO2MasterReset(MRS2)togetherwiththeFIFO1MasterReset(MRS1)
inputlatchesthevalueoftheBig-Endian(BE)inputforPortBandalsolatches
thevaluesoftheFlagSelect(FS0,FS1andFS2)inputsforchoosingtheAlmost-
FullandAlmost-Emptyoffsetprogrammingmethod. (FordetailsseeTable1,
FlagProgramming,andtheProgrammingtheAlmost-EmptyandAlmost-Full
Flagssection). TherelevantFIFOMasterResettimingdiagramcanbefound
in Figure 3.
A LOW on the BE/FWFT input when the Master Reset (MRS1, MRS2)
inputsgofromLOWtoHIGHwillselectaLittle-Endianarrangement.Whendata
ismovinginthedirectionfromPortAtoPortB,theleastsignificantbyte(word)
ofthelongwordwrittentoPortAwillbereadfromPortBfirst;themostsignificant
byte(word)ofthelongwordwrittentoPortAwillbereadfromPortBlast.When
data is movinginthe directionfromPortBtoPortA, the byte (word)written
toPortBfirstwillbereadfromPortAastheleastsignificantbyte(word)ofthe
long word; the byte (word) written to Port B last will be read from Port A as
the most significant byte (word) of the long word. Refer to Figure 2 for an
illustrationoftheBEfunction.SeeFigure3(MasterReset)fortheEndianselect
timingdiagram.
PARTIAL RESET (PRS1, PRS2)
EachofthetwoFIFOmemoriesofthesedevicesundergoesalimitedreset
bytakingits associatedPartialReset(PRS1,PRS2)inputLOWforatleast
four Port A Clock (CLKA) and four Port B Clock (CLKB) LOW-to-HIGH
transitions.ThePartialResetinputscanswitchasynchronouslytotheclocks.
APartialResetinitializestheinternalreadandwritepointersandforcesthe
Full/Input Ready flag (FFA/IRA, FFB/IRB) LOW, the Empty/Output Ready
flag (EFA/ORA, EFB/ORB) LOW, the Almost-Empty flag (AEA, AEB)
LOW,andtheAlmost-Fullflag(AFA,AFB)HIGH.APartialResetalsoforces
theMailboxFlag(MBF1,MBF2)oftheparallelmailboxregisterHIGH.After
a PartialReset,the FIFO’s Full/InputReadyflagis setHIGHaftertwowrite
clock cycles. Then the FIFO is ready to be written to.
— TIMING MODE SELECTION
AfterMasterReset,theFWFTselectfunctionisactive,permittingachoice
betweentwopossibletimingmodes:IDTStandardmodeorFirstWordFall
Through (FWFT) mode. Once the Master Reset (MRS1, MRS2) input is
HIGH, a HIGH on the BE/FWFT input during the next LOW-to-HIGH
transitionofCLKA(forFIFO1)andCLKB(forFIFO2)willselectIDTStandard
mode. This mode uses the Empty Flag function (EFA, EFB) to indicate
whetherornotthereareanywordspresentintheFIFOmemory.Itusesthe
Full Flag function (FFA, FFB) to indicate whether or not the FIFO memory
Whateverflagoffsets,programmingmethod(parallelorserial),andtiming
mode(FWFTorIDTStandardmode)arecurrentlyselectedatthetimeaPartial
Resetisinitiated,thosesettingswillberemainunchangeduponcompletionof
the reset operation. A Partial Reset may be useful in the case where
reprogrammingaFIFOfollowingaMasterResetwouldbeinconvenient.See
Figure4forthePartialResettimingdiagram.
RETRANSMIT (RT1, RT2)
TheFIFO1memoryofthesedevicesundergoesaRetransmitbytakingits hasanyfreespaceforwriting.InIDTStandardmode,everywordreadfrom
associatedRetransmit (RT1)inputLOWforatleastfourPortAClock(CLKA) theFIFO,includingthefirst,mustberequestedusingaformalreadoperation.
NOTE:
1. Either a HIGH or LOW can be applied to a "don't care" input with no change to the logical operation of the FIFO. Nevertheless, inputs that are temporarily "don't care" (along with
unused inputs) must not be left open, rather they must be either HIGH or LOW.
11
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
orLOWduringamasterreset.Forexample,toloadthepresetvalueof64into
X1andY1,FS0,FS1andFS2mustbeHIGHwhenFlFO1reset(MRS1)returns
HIGH.Flag-offsetregisters associatedwithFIFO2areloadedwithoneofthe
preset values in the same way with FIFO2 Master Reset (MRS2), toggled
simultaneously with FIFO1 Master Reset (MRS1). For relevant preset value
loading timing diagram, see Figure 3.
OncetheMasterReset(MRS1,MRS2)inputisHIGH,aLOWontheBE/
FWFTinputduringthenextLOW-to-HIGHtransitionofCLKA(forFIFO1)and
CLKB(forFIFO2)willselectFWFTmode.ThismodeusestheOutputReady
function(ORA,ORB)toindicatewhetherornotthereisvaliddataatthedata
outputs(A0-A35orB0-B35).ItalsousestheInputReadyfunction(IRA,IRB)
toindicate whetherornotthe FIFOmemoryhas anyfree space forwriting.
IntheFWFTmode,thefirstwordwrittentoanemptyFIFOgoesdirectlytodata
outputs,noreadrequestnecessary. Subsequentwordsmustbeaccessed
byperforminga formalreadoperation.
PARALLEL LOAD FROM PORT A
ToprogramtheX1,X2,Y1,andY2registersfromPortA,performaMaster
ResetonbothFlFOs simultaneouslywithFS2HIGHorLOW, FS0andFS1
LOWduringtheLOW-to-HIGHtransitionofMRS1andMRS2.ThestateofFS2
atthispointofresetwilldeterminewhethertheparallelprogrammingmethod
hasInterspersedParityorNon-InterspersedParity.RefertoTable1forFlag
Programming Flag Offset setup . It is important to note that once parallel
programminghasbeenselectedduringaMasterResetbyholdingbothFS0
& FS1 LOW, these inputs must remain LOW during all subsequent FIFO
operation. They can only be toggled HIGH when future Master Resets are
performedandotherprogrammingmethodsaredesired.
Afterthisresetiscomplete,thefirstfourwritestoFIFO1donotstoredata
in RAM but load the Offset registers in the order Y1, X1, Y2, X2. For Non-
InterspersedParitymodethePortAdatainputsusedbytheOffsetregistersare
(A10-A0), (A11-A0), or (A12-A0) for the IDT72V3654, IDT72V3664, or
IDT72V3674,respectively.ForInterspersedParitymodethePortAdatainputs
usedbytheOffsetregistersare(A11-A9,A7-A0),(A12-A9,A7-A0),or(A13-
A9,A7-A0)fortheIDT72V3654,IDT72V3664,orIDT72V3674,respectively.
The highest numbered input is used as the most significant bit of the binary
numberineachcase.Validprogrammingvaluesfortheregistersrangefrom
1to2,044fortheIDT72V3654;1to4,092fortheIDT72V3664;and1to8,188
fortheIDT72V3674.AfteralltheoffsetregistersareprogrammedfromPortA,
FollowingMasterReset,thelevelappliedtotheBE/FWFTinputtochoose
thedesiredtimingmodemustremainstaticthroughoutFIFOoperation.Refer
toFigure3(MasterReset)foraFirstWordFallThroughselecttimingdiagram.
PROGRAMMINGTHEALMOST-EMPTYANDALMOST-FULLFLAGS
FourregistersintheIDT72V3654/72V3664/72V3674areusedtoholdthe
offsetvaluesfortheAlmost-EmptyandAlmost-Fullflags.ThePortBAlmost-
Emptyflag(AEB)Offsetregisteris labeledX1andthePortAAlmost-Empty
flag (AEA) Offset register is labeled X2. The Port A Almost-Full flag (AFA)
OffsetregisterislabeledY1andthePortBAlmost-Fullflag(AFB)Offsetregister
islabeledY2.TheindexofeachregisternamecorrespondstoitsFIFOnumber.
TheoffsetregisterscanbeloadedwithpresetvaluesduringtheresetofaFIFO,
programmedinparallelusingtheFIFO’sPortAdatainputs,orprogrammed
in serial using the Serial Data (SD) input (see Table 1).
FS0/SD,FS1/SENandFS2functionthesamewayinbothIDTStandard
andFWFTmodes.
— PRESET VALUES
ToloadaFIFO’sAlmost-EmptyflagandAlmost-FullflagOffsetregisterswith
oneofthefivepresetvalueslistedinTable1,theflagselectinputsmustbeHIGH
TABLE 1 — FLAG PROGRAMMING
FS2
FS1/SEN
FS0/SD
MRS1
MRS2
X1 AND Y1 REGlSTERS(1)
X2 AND Y2 REGlSTERS(2)
H
H
H
H
H
L
L
H
H
L
L
H
L
L
H
H
L
↑
X
↑
X
↑
X
↑
X
↑
X
↑
↑
↑
X
↑
X
↑
X
↑
X
↑
X
↑
↑
↑
↑
64
X
H
X
64
H
16
X
H
L
X
16
H
H
H
H
H
H
H
L
8
X
H
X
8
L
256
X
L
X
256
L
1,024
X
1,024
L
X
L
H
SerialprogrammingviaSD
SerialprogrammingviaSD
(3,5)
(3,5)
L
ParallelprogrammingviaPortA
ParallelprogrammingviaPortA
IP Mode(4, 5)
L
L
IP Mode(4, 5)
NOTES:
1. X1 register holds the offset for AEB; Y1 register holds the offset for AFA.
2. X2 register holds the offset for AEA; Y2 register holds the offset for AFB.
3. When this method of parallel programming is selected, Port A will assume Non-Interspersed Parity.
4. When IP Mode is selected, only parallel programming of the offset values via Port A, can be performed and Port A will assume Interspersed Parity.
5. IF parallel programming is selected during a Master Reset, then FS0 & FS1 must remain LOW during FIFO operation.
12
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
thePortBFull/InputReadyflag(FFB/IRB)issetHIGH,andbothFIFOsbegin X1,Y2,andfinally,X2. Thefirst-bitwritestoresthemostsignificantbitoftheY1
normaloperation.RefertoFigure5foratimingdiagramillustrationofparallel registerandthelast-bitwritestorestheleastsignificantbitoftheX2register.Each
programmingoftheflagoffsetvalues.
registervaluecanbeprogrammedfrom1to2,044(IDT72V3654),1to4,092
(IDT72V3664), or 1 to 8,188 (IDT72V3674).
INTERSPERSED PARITY
Whentheoptiontoprogramtheoffsetregistersseriallyischosen,thePort
InterspersedParityisselectedduringaMasterResetoftheFIFO.Referto AFull/InputReady(FFA/IRA)flagremainsLOWuntilallregisterbitsarewritten.
Table1fortheset-upconfigurationofInterspersedParity.TheInterspersed FFA/IRAissetHIGHbytheLOW-to-HIGHtransitionofCLKAafterthelastbit
Parityfunctionallowstheusertoselectthelocationoftheparitybitsintheword isloadedtoallownormalFIFO1operation.ThePortBFull/InputReady(FFB/
loadedintotheparallelport(A0-An)duringprogrammingoftheflagoffsetvalues. IRB)flagalsoremainsLOWthroughouttheserialprogrammingprocess,until
IfInterspersedParityisselectedthenduringparallelprogrammingoftheflag allregisterbitsarewritten.FFB/IRBissetHIGHbytheLOW-to-HIGHtransition
TABLE 2 — PORT A ENABLE FUNCTION TABLE
CSA
W/RA
ENA
MBA
CLKA
Data A (A0-A35) I/O
Port Function
H
L
L
L
L
L
L
L
X
H
H
H
L
X
L
X
X
L
X
X
↑
High-Impedance
Input
None
None
H
H
L
Input
FIFO1 write
Mail1write
H
L
↑
Input
X
↑
Output
Output
Output
Output
None
L
H
L
L
FIFO2read
None
L
H
H
X
↑
L
H
Mail2 read (set MBF2 HIGH)
TABLE 3 — PORT B ENABLE FUNCTION TABLE
CSB
W/RB
ENB
MBB
CLKB
Data B (B0-B35) I/O
Port Function
H
L
L
L
L
L
L
L
X
L
X
L
X
X
L
X
X
↑
High-Impedance
Input
None
None
L
H
H
L
Input
FIFO2 write
Mail2write
L
H
L
↑
Input
H
H
H
H
X
↑
Output
Output
Output
Output
None
H
L
L
FIFO1read
None
H
H
X
↑
H
Mail1 read (set MBF1 HIGH)
offsetvalues,thedevicewillignoredatalineA8.IfNon-InterspersedParityis ofCLKBafterthelastbitisloadedtoallownormalFIFO2operation. SeeFigure 6
selectedthendatalineA8willbecomeavalidbit.IfInterspersedParityisselected forSerialProgrammingoftheAlmost-FullFlagandAlmost-EmptyFlagOffset
serialprogrammingoftheoffsetvaluesisnotpermitted,onlyparallelprogram- Values (IDT Standard and FWFT Modes) timing diagram.
ming can be done.
FIFO WRITE/READ OPERATION
— SERIAL LOAD
ThestateofthePortAdata(A0-A35)linesiscontrolledbyPortAChipSelect
ToprogramtheX1,X2,Y1,andY2registersserially,initiateaMasterReset (CSA)andPortAWrite/Readselect(W/RA).TheA0-A35linesareintheHigh-
withFS2LOW,FS0/SDLOWandFS1/SENHIGHduringtheLOW-to-HIGH impedance state wheneither CSA orW/RAis HIGH. The A0-A35lines are
transitionofMRS1andMRS2.Afterthisresetiscomplete,theXandYregister active outputs whenbothCSA andW/RAare LOW.
valuesareloadedbit-wisethroughtheFS0/SDinputoneachLOW-to-HIGH
Data is loaded into FIFO1 from the A0-A35 inputs on a LOW-to-HIGH
transitionofCLKAthattheFS1/SENinputisLOW.Thereare44-,48-,or52- transitionofCLKAwhenCSAisLOW,W/RAisHIGH,ENAisHIGH,MBAis
bitwritesneededtocompletetheprogrammingfortheIDT72V3654,IDT72V3664, LOW,andFFA/IRAisHIGH.DataisreadfromFIFO2totheA0-A35outputs
or IDT72V3674, respectively. The four registers are written in the order Y1, by a LOW-to-HIGH transition of CLKA when CSA is LOW, W/RA is LOW,
13
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
TABLE 4 — FIFO1 FLAG OPERATION (IDT Standard and FWFT modes)
Synchronized
to CLKB
Synchronized
to CLKA
Number of Words in FIFO Memory(1,2)
(3)
(3)
(3)
IDT72V3654
IDT72V3664
IDT72V3674
EFB/ORB
AEB
AFA
FFA/IRA
0
1toX1
0
1toX1
0
1toX1
L
H
H
H
H
L
L
H
H
H
L
H
H
H
H
L
(X1+1)to[2,048-(Y1+1)]
(2,048-Y1)to2,047
2,048
(X1+1)to[4,096-(Y1+1)]
(4,096-Y1)to4,095
4,096
(X1+1)to[8,192-(Y1+1)]
(8,192-Y1)to8,191
8,192
H
H
H
L
NOTES:
1. When a word loaded to an empty FIFO is shifted to the output register, its previous FIFO memory location is free.
2. Data in the output register does not count as a "word in FIFO memory". Since in FWFT mode, the first word written to an empty FIFO goes unrequested to the output register (no read
operation necessary), it is not included in the FIFO memory count.
3. X1 is the Almost-Empty offset for FIFO1 used by AEB. Y1 is the Almost-Full offset for FIFO1 used by AFA. Both X1 and Y1 are selected during a FIFO1 reset or port A programming.
4. The ORB and IRA functions are active during FWFT mode; the EFB and FFA functions are active in IDT Standard mode.
TABLE 5 — FIFO2 FLAG OPERATION (IDT Standard and FWFT modes)
Synchronized
to CLKA
Synchronized
to CLKB
Number of Words in FIFO Memory(1,2)
(3)
(3)
(3)
IDT72V3654
IDT72V3664
IDT72V3674
EFA/ORA
AEA
AFB
H
FFB/IRB
0
0
1toX2
0
L
H
H
H
H
L
L
H
H
H
H
L
1toX2
1toX2
H
(X2+1)to[2,048-(Y2+1)]
(2,048-Y2)to2,047
2,048
(X2+1)to[4,096-(Y2+1)]
(4,096-Y2)to4,095
4,096
(X2+1)to[8,192-(Y2+1)]
(8,192-Y2)to8,191
8,192
H
H
H
H
L
L
NOTES:
1. When a word loaded to an empty FIFO is shifted to the output register, its previous FIFO memory location is free.
2. Data in the output register does not count as a "word in FIFO memory". Since in FWFT mode, the first word written to an empty FIFO goes unrequested to the output register (no read
operation necessary), it is not included in the FIFO memory count.
3. X2 is the Almost-Empty offset for FIFO2 used by AEA. Y2 is the Almost-Full offset for FIFO2 used by AFB. Both X2 and Y2 are selected during a FIFO2 reset or port A programming.
4. The ORA and IRB functions are active during FWFT mode; the EFA and FFB functions are active in IDT Standard mode.
andarenotrelatedtohigh-impedancecontrolofthedataoutputs.Ifaportenable
isLOWduringaclockcycle,theport’sChipSelectandWrite/Readselectmay
changestates duringthesetupandholdtimewindowofthecycle.
WhenoperatingtheFIFOinFWFTmodeandtheOutputReadyflagisLOW,
thenextwordwrittenisautomaticallysenttotheFIFO’soutputregisterbythe
LOW-to-HIGHtransitionoftheportclockthatsetstheOutputReadyflagHIGH.
WhentheOutputReadyflagisHIGH,subsequentdataisclockedtotheoutput
registersonlywhenareadisselectedusingtheport’sChipSelect,Write/Read
select,Enable,andMailboxselect.
WhenoperatingtheFIFOinIDTStandardmode,thefirstwordwillcause
theEmptyFlagtochangestateonthesecondLOW-to-HIGHtransitionofthe
ReadClock. Thedatawordwillnotbeautomaticallysenttotheoutputregister.
Instead, data residing in the FIFO's memory array is clocked to the output
registeronlywhenareadisselectedusingtheport’sChipSelect,Write/Read
select,Enable,andMailboxselect.WriteandreadtimingdiagramsforPortA
canbefoundinFigure7and14. RelevantPortBwriteandreadcycle timing
diagrams togetherwithBus-MatchingandEndianselectoperations canbe
found in Figures 8 through 13.
ENA is HIGH, MBA is LOW, and EFA/ORA is HIGH (see Table 2). FIFO
reads and writes on Port A are independent of any concurrent Port B
operation.
The Port B control signals are identical to those of Port A with the
exceptionthatthePortBWrite/Readselect(W/RB)istheinverseofthePort
A Write/Read select (W/RA). The state ofthe PortBdata (B0-B35)lines is
controlled by the Port B Chip Select (CSB) and Port B Write/Read select
(W/RB).TheB0-B35linesareinthehigh-impedancestatewheneitherCSB
isHIGHorW/RBisLOW.TheB0-B35linesareactiveoutputswhenCSBis
LOW and W/RB is HIGH.
Data is loaded into FIFO2 from the B0-B35 inputs on a LOW-to-HIGH
transitionofCLKBwhenCSBisLOW,W/RBisLOW,ENBisHIGH,MBBis
LOW,andFFB/IRBisHIGH.DataisreadfromFIFO1totheB0-B35outputs
byaLOW-to-HIGHtransitionofCLKBwhenCSBisLOW,W/RBisHIGH,ENB
isHIGH,MBBisLOW,andEFB/ORBisHIGH(seeTable3).FIFOreadsand
writes on Port B are independent of any concurrent Port A operation.
The setup and hold time constraints to the port clocks for the port Chip
SelectsandWrite/Readselectsareonlyforenablingwriteandreadoperations
14
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
comparatorthatindicateswhentheFlFOmemorystatusisfull,full-1,orfull-
2.FromthetimeawordisreadfromaFIFO,itspreviousmemorylocationis
readytobewrittentoinaminimumoftwocyclesoftheFull/InputReadyflag
synchronizingclock.Therefore,anFull/InputReadyflagisLOWiflessthan
twocyclesoftheFull/InputReadyflagsynchronizingclockhaveelapsedsince
the nextmemorywrite locationhas beenread. The secondLOW-to-HIGH
transitionontheFull/InputReadyflagsynchronizingclockafterthereadsets
the Full/InputReadyflagHIGH.
SYNCHRONIZED FIFO FLAGS
EachFIFOis synchronizedtoits portclockthroughatleasttwoflip-flop
stages.Thisisdonetoimproveflag-signalreliabilitybyreducingtheprobability
ofmetastableeventswhenCLKAandCLKBoperateasynchronouslytoone
another. EFA/ORA, AEA, FFA/IRA, and AFA are synchronized to CLKA.
EFB/ORB,AEB,FFB/IRB,andAFBaresynchronizedtoCLKB.Tables4and
5 show the relationship of each port flag to FIFO1 and FIFO2.
EMPTY/OUTPUTREADYFLAGS(EFA/ORA,EFB/ORB)
ALOW-to-HIGHtransitiononaFull/InputReadyflagsynchronizingclock
beginsthefirstsynchronizationcycleofareadiftheclocktransitionoccursat
timetSKEW1orgreateraftertheread.Otherwise,thesubsequentclockcycle
can be the first synchronization cycle (see Figures 19, 20, 21, and 22).
Thesearedualpurposeflags. IntheFWFTmode,theOutputReady(ORA,
ORB)functionisselected.WhentheOutput-ReadyflagisHIGH,newdatais
presentintheFIFOoutputregister.WhentheOutputReadyflagisLOW,the
previousdatawordispresentintheFIFOoutputregisterandattemptedFIFO
reads are ignored.
ALMOST-EMPTYFLAGS(AEA,AEB)
IntheIDTStandardmode,theEmptyFlag(EFA,EFB)functionisselected.
WhentheEmptyFlagisHIGH,dataisavailableintheFIFO’sRAMmemory
forreadingtotheoutputregister.WhentheEmptyFlagisLOW,theprevious
datawordispresentintheFIFOoutputregisterandattemptedFIFOreadsare
ignored.
TheEmpty/OutputReadyflagofaFIFOissynchronizedtotheportclock
thatreadsdatafromitsarray.ForboththeFWFTandIDTStandardmodes,
theFIFOreadpointeris incrementedeachtimeanewwordis clockedtoits
outputregister.ThestatemachinethatcontrolsanOutputReadyflagmonitors
a write pointer and read pointer comparator that indicates when the FIFO
memorystatusisempty,empty+1,orempty+2.
TheAlmost-EmptyflagofaFIFOissynchronizedtotheportclockthatreads
data from its array. The state machine that controls an Almost-Empty flag
monitorsawritepointerandreadpointercomparatorthatindicateswhenthe
FIFOmemorystatusisalmost-empty,almost-empty+1,oralmost-empty+2.
Thealmost-emptystateisdefinedbythecontentsofregisterX1forAEBand
registerX2forAEA.Theseregistersareloadedwithpresetvaluesduringa
FIFOreset,programmedfromPortA,orprogrammedserially(seeAlmost-
Empty flag and Almost-Full flag offset programming section). An Almost-
EmptyflagisLOWwhenitsFIFOcontainsXorlesswordsandisHIGHwhen
itsFIFOcontains(X+1)ormorewords.AdatawordpresentintheFIFOoutput
registerhas beenreadfrommemory.
InFWFTmode,fromthetimeawordiswrittentoaFIFO,itcanbeshifted
totheFIFOoutputregisterinaminimumofthreecyclesoftheOutputReady
flagsynchronizingclock. Therefore, anOutputReadyflagis LOWifa word
inmemoryisthenextdatatobesenttotheFlFOoutputregisterandthreecycles
oftheportClockthatreadsdatafromtheFIFOhavenotelapsedsincethetime
thewordwaswritten.TheOutputReadyflagoftheFIFOremainsLOWuntil
thethirdLOW-to-HIGHtransitionofthesynchronizingclockoccurs,simulta-
neouslyforcingtheOutputReadyflagHIGHandshiftingthewordtotheFIFO
outputregister.
InIDTStandardmode,fromthetimeawordiswrittentoaFIFO,theEmpty
Flagwillindicatethepresenceofdataavailableforreadinginaminimumof
twocyclesoftheEmptyFlagsynchronizingclock.Therefore,anEmptyFlag
isLOWifawordinmemoryisthenextdatatobesenttotheFlFOoutputregister
andtwocyclesoftheportClockthatreadsdatafromtheFIFOhavenotelapsed
sincethetimethewordwaswritten.TheEmptyFlagoftheFIFOremainsLOW
untilthesecondLOW-to-HIGHtransitionofthesynchronizingclockoccurs,
forcing the Empty Flag HIGH; only then can data be read.
TwoLOW-to-HIGHtransitions ofthe Almost-Emptyflagsynchronizing
clockarerequiredafteraFIFOwriteforitsAlmost-Emptyflagtoreflectthenew
leveloffill.Therefore,theAlmost-FullflagofaFIFOcontaining(X+1)ormore
wordsremainsLOWiftwocyclesofitssynchronizingclockhavenotelapsed
sincethewritethatfilledthememorytothe(X+1)level.AnAlmost-Emptyflag
issetHIGHbythesecondLOW-to-HIGHtransitionofitssynchronizingclock
after the FIFO write that fills memory to the (X+1) level. A LOW-to-HIGH
transitionofanAlmost-Emptyflagsynchronizingclockbeginsthefirstsynchro-
nizationcycleifitoccursattimetSKEW2 orgreaterafterthewritethatfillsthe
FIFOto(X+1)words.Otherwise,thesubsequentsynchronizingclockcycle
may be the first synchronization cycle. (See Figure 23 and 24).
ALMOST-FULL FLAGS (AFA, AFB)
TheAlmost-FullflagofaFIFOissynchronizedtotheportclockthatwrites
datatoitsarray.ThestatemachinethatcontrolsanAlmost-Fullflagmonitors
a write pointer and read pointer comparator that indicates when the FIFO
memorystatusisalmost-full,almost-full-1,oralmost-full-2.Thealmost-fullstate
isdefinedbythecontentsofregisterY1forAFAandregisterY2forAFB.These
registersareloadedwithpresetvaluesduringaFlFOreset,programmedfrom
PortA,orprogrammedserially(seeAlmost-EmptyflagandAlmost-Fullflag
offsetprogrammingsection).AnAlmost-FullflagisLOWwhenthenumberof
wordsinitsFIFOisgreaterthanorequalto(2,048-Y),(4,096-Y),or(8,192-Y)
fortheIDT72V3654,IDT72V3664,orIDT72V3674respectively.AnAlmost-
Fullflagis HIGHwhenthe numberofwords inits FIFOis less thanorequal
to [2,048-(Y+1)], [4,096-(Y+1)], or [8,192-(Y+1)] for the IDT72V3654,
IDT72V3664,orIDT72V3674respectively.Notethatadatawordpresentin
the FIFOoutputregisterhas beenreadfrommemory.
TwoLOW-to-HIGHtransitionsoftheAlmost-Fullflagsynchronizingclock
arerequiredafteraFIFOreadforitsAlmost-Fullflagtoreflectthenewlevel
offill.Therefore,theAlmost-FullflagofaFIFOcontaining[2,048/4,096/8,192-
(Y+1)]orlesswordsremainsLOWiftwocyclesofitssynchronizingclockhave
notelapsedsince the readthatreducedthe numberofwords inmemoryto
[2,048/4,096/8,192-(Y+1)]. An Almost-Full flag is set HIGH by the second
ALOW-to-HIGHtransitiononanEmpty/OutputReadyflagsynchronizing
clockbeginsthefirstsynchronizationcycleofawriteiftheclocktransitionoccurs
attimetSKEW1orgreaterafterthewrite.Otherwise,thesubsequentclockcycle
can be the first synchronization cycle (see Figures 15, 16, 17, and 18).
FULL/INPUT READY FLAGS (FFA/IRA, FFB/IRB)
Thisisadualpurposeflag.InFWFTmode,theInputReady(IRAandIRB)
function is selected. In IDT Standard mode, the Full Flag (FFA and FFB)
functionisselected.Forbothtimingmodes,whentheFull/InputReadyflagis
HIGH,amemorylocationisfreeintheFIFOtoreceivenewdata.Nomemory
locationsarefreewhentheFull/InputReadyflagisLOWandattemptedwrites
to the FIFO are ignored.
TheFull/InputReadyflagofaFlFOissynchronizedtotheportclockthat
writesdatatoitsarray.ForbothFWFTandIDTStandardmodes,eachtime
awordiswrittentoaFIFO,itswritepointerisincremented.Thestatemachine
thatcontrolsaFull/InputReadyflagmonitorsawritepointerandreadpointer
15
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
LOW-to-HIGHtransitionofits synchronizingclockafterthe FIFOreadthat BUS SIZING
reduces the number of words in memory to [2,048/4,096/8,192-(Y+1)]. A
The Port B bus can be configured in a 36-bit long word, 18-bit word, or
LOW-to-HIGHtransitionofanAlmost-Fullflagsynchronizingclockbeginsthe 9-bit byte format for data read from FIFO1 or written to FIFO2. The levels
appliedtothePortBBusSizeselect(SIZE)andtheBus-Matchselect(BM)
determinethePortBbussize.TheselevelsshouldbestaticthroughoutFIFO
operation. Both bus size selections are implemented at the completion of
MasterReset,bythetimetheFull/InputReadyflagissetHIGH,asshownin
Figure 2.
firstsynchronizationcycleifitoccursattime tSKEW2 orgreateraftertheread
thatreducesthenumberofwordsinmemoryto[2,048/4,096/8,192-(Y+1)].
Otherwise,thesubsequentsynchronizingclockcyclemaybethefirstsynchro-
nization cycle (see Figure 25 and 26).
TwodifferentmethodsforsequencingdatatransferareavailableforPort
Bwhenthebussizeselectioniseitherbyte-orword-size.Theyarereferred
toasBig-Endian(mostsignificantbytefirst)andLittle-Endian(leastsignificant
bytefirst).ThelevelappliedtotheBig-Endianselect(BE)inputduringtheLOW-
to-HIGHtransitionofMRS1andMRS2selectstheendianmethodthatwillbe
active during FIFO operation. BE is a don’t care input when the bus size
selected for Port B is long word. The endian method is implemented at the
completionofMasterReset,bythetimetheFull/InputReadyflagissetHIGH,
as shown in Figure 2.
Only36-bitlongworddataiswrittentoorreadfromthetwoFIFOmemories
ontheIDT72V3654/72V3664/72V3674.Bus-matchingoperationsaredone
afterdataisreadfromtheFIFO1RAMandbeforedataiswrittentotheFIFO2
RAM. These bus-matching operations are not available when transferring
data via mailbox registers. Furthermore, both the word- and byte-size bus
selections limit the width of the data bus that can be used for mail register
operations.Inthiscase,onlythosebytelanesbelongingtotheselectedword-
orbyte-sizebus cancarrymailboxdata.Theremainingdataoutputs willbe
indeterminate. The remaining data inputs will be don’t care inputs. For
example, when a word-size bus is selected, then mailbox data can be
transmitted only between A0-A17 and B0-B17. When a byte-size bus is
selected,thenmailboxdatacanbetransmittedonlybetweenA0-A8andB0-
B8. (See Figures 27 and 28).
MAILBOX REGISTERS
Each FIFO has a 36-bit bypass register to pass command and control
informationbetweenPortAandPortBwithoutputtingitinqueue.TheMailbox
select(MBA, MBB)inputs choose betweena mailregisteranda FIFOfora
port data transfer operation. The usable width of both the Mail1 and Mail2
registersmatchestheselectedbussizeforPortB.
ALOW-to-HIGHtransitiononCLKAwritesdatatotheMail1Registerwhen
a Port A write is selected by CSA, W/RA, and ENA with MBA HIGH. If the
selectedPortBbussizeisalso36bits,thentheusablewidthoftheMail1register
employsdatalinesA0-A35.IftheselectedPortBbussizeis18bits,thenthe
usablewidthoftheMail1RegisteremploysdatalinesA0-A17.(Inthiscase,
A18-A35aredon’tcareinputs.)IftheselectedPortBbus sizeis 9bits,then
theusablewidthoftheMail1RegisteremploysdatalinesA0-A8.(Inthiscase,
A9-A35 are don’t care inputs.)
A LOW-to-HIGH transition on CLKB writes B0-B35 data to the Mail2
RegisterwhenaPortBwriteisselectedbyCSB,W/RB,andENBwithMBB
HIGH.IftheselectedPortBbus sizeis also36bits,thentheusablewidthof
theMail2employsdatalinesB0-B35.IftheselectedPortBbussizeis18bits,
thentheusablewidthoftheMail2RegisteremploysdatalinesB0-B17.(Inthis
case,B18-B35aredon’tcareinputs.)IftheselectedPortBbussizeis9bits,
thentheusablewidthoftheMail2RegisteremploysdatalinesB0-B8.(Inthis
case, B9-B35are don’tcare inputs.)
Writingdatatoamailregistersetsitscorrespondingflag(MBF1orMBF2)
LOW.AttemptedwritestoamailregisterareignoredwhilethemailflagisLOW.
Whendataoutputsofaportareactive,thedataonthebuscomesfromthe
FIFOoutputregisterwhentheportMailboxselectinputisLOWandfromthe
mailregisterwhenthe portMailboxselectinputis HIGH.
TheMail1RegisterFlag(MBF1)issetHIGHbyaLOW-to-HIGHtransition
onCLKBwhenaPortBreadisselectedbyCSB,W/RB,andENBwithMBB
HIGH. For a 36-bit bus size, 36 bits of mailbox data are placed on B0-B35.
Foran18-bitbussize,18bitsofmailboxdataareplacedonB0-B17.(Inthis
case,B18-B35areindeterminate.)Fora9-bitbussize,9bitsofmailboxdata
are placed on B0-B8. (In this case, B9-B35 are indeterminate.)
TheMail2RegisterFlag(MBF2)issetHIGHbyaLOW-to-HIGHtransition
onCLKAwhenaPortAreadisselectedbyCSA,W/RA,andENAwithMBA
HIGH.
Fora 36-bitbus size, 36bits ofmailboxdata are placedonA0-A35. For
an18-bitbussize,18bitsofmailboxdataareplacedonA0-A17.(Inthiscase,
A18-A35are indeterminate.)Fora 9-bitbus size, 9bits ofmailboxdata are
placedonA0-A8. (Inthis case, A9-A35are indeterminate.)
Thedatainamailregisterremainsintactafteritisreadandchangesonly
whennewdataiswrittentotheregister.TheEndianselectfeaturehasnoeffect
onmailboxdata.FormailregisterandMailRegisterFlagtimingdiagrams,see
Figure 27 and 28.
BUS-MATCHING FIFO1 READS
DataisreadfromtheFIFO1RAMin36-bitlongwordincrements.Ifalong
wordbus sizeis implemented,theentirelongwordimmediatelyshifts tothe
FIFO1outputregister.IfbyteorwordsizeisimplementedonPortB,onlythe
firstoneortwobytesappearontheselectedportionoftheFIFO1outputregister,
with the rest of the long word stored in auxiliary registers. In this case,
subsequentFIFO1readsoutputtherestofthelongwordtotheFIFO1output
register in the order shown by Figure 2.
WhenreadingdatafromFIFO1inbyteorwordformat,theunusedB0-B35
outputsareindeterminate.
BUS-MATCHING FIFO2 WRITES
DataiswrittentotheFIFO2RAMin36-bitlongwordincrements.Datawritten
toFIFO2withabyteorwordbussizestorestheinitialbytesorwordsinauxiliary
registers.TheCLKBrisingedgethatwritesthefourthbyteorthesecondword
oflongwordtoFIFO2alsostorestheentirelongwordintheFIFO2memory.
The bytes are arranged in the manner shown in Figure 2.
WhenwritingdatatoFIFO2inbyteorwordformat,theunusedB0-B35inputs
aredon'tcareinputs.
16
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
A35 A27
A26 A18
A17 A9
A8 A0
BYTE ORDER ON PORT A:
Write to FIFO1/
Read from FIFO2
D
A
B
C
B35 B27
B26 B18
B17 9
B8 B0
BYTE ORDER ON PORT B:
BE BM SIZE
Read from FIFO1/
Write to FIFO2
A
B
D
C
X
L
X
(a) LONG WORD SIZE
B35 B27
B35 B27
B26 B18
B26 B18
B17 B9
B8 B0
1st: Read from FIFO1/
Write to FIFO2
BE BM SIZE
A
B
H
H
L
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
C
D
(b) WORD SIZE BIG ENDIAN
B35 B27
B35 B27
B26 B18
B17 B9
B8 B0
1st: Read from FIFO1/
Write to FIFO2
BE BM SIZE
C
D
L
H
L
B26 B18
B17 B9
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
A
B
(c) WORD SIZE LITTLE-ENDIAN
B35 B27
B35 B27
B35 B27
B35 B27
B26 B18
B26 B18
B26 B18
B26 B18
B17 B9
B17 B9
B17 B9
B17 B9
B8 B0
BE BM SIZE
1st: Read from FIFO1/
Write to FIFO2
A
H
H
H
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
B
B8 B0
3rd: Read from FIFO1/
Write to FIFO2
C
B8 B0
4th: Read from FIFO1/
Write to FIFO2
D
(d) BYTE SIZE BIG-ENDIAN
B35 B27
B35 B27
B35 B27
B35 B27
B26 B18
B26 B18
B26 B18
B26 B18
B17 B9
B17 B9
B17 B9
B17 B9
B8 B0
BE BM SIZE
1st: Read from FIFO1/
Write to FIFO2
D
L
H
H
B8 B0
2nd: Read from FIFO1/
Write to FIFO2
C
B8 B0
3rd: Read from FIFO1/
Write to FIFO2
B
B8 B0
4th: Read from FIFO1/
Write to FIFO2
A
4664 drw 04
(e) BYTE SIZE LITTLE-ENDIAN
Figure 2. Bus Sizing
17
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
t
RSTS
tRSTH
MRS1
tBEH
t
BES
tFWS
BE
0,1
BE/FWFT
FWFT
t
FSS
tFSH
FS2,
FS1,FS0
t
WFF
t
WFF
FFA/IRA
EFB/ORB
AEB
(3)
REF
t
t
RSF
t
RSF
AFA
t
RSF
MBF1
LOW
RTM
4664 drw 05
NOTES:
1. FIFO2 Master Reset (MRS2) is performed in the same manner to load X2 and Y2 with a preset value. For FIFO2 Master Reset, MRS1 must toggle simultaneously with MRS2.
2. PRS1 must be HIGH during Master Reset.
3. If BE/FWFT is HIGH, then EFB/ORB will go LOW one CLKB cycle earlier than in this case where BE/FWFT is LOW.
Figure 3. FIFO1 Master Reset and Loading X1 and Y1 with a Preset Value of Eight(1) (IDT Standard and FWFT Modes)
CLKA
CLKB
t
RSTS
tRSTH
PRS1
t
WFF
t
WFF
FFA/IRA
(3)
tREF
EFB/ORB
t
RSF
AEB
AFA
t
RSF
t
RSF
MBF1
RTM
LOW
4664 drw 06
NOTES:
1. Partial Reset is performed in the same manner for FIFO2.
2. MRS1 must be HIGH during Partial Reset.
3. If BE/FWFT is HIGH, then EFB/ORB will go LOW one CLKB cycle earlier than in this case where BE/FWFT is LOW.
Figure 4. FIFO1 Partial Reset(1) (IDT Standard and FWFT Modes)
18
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
2
1
4
MRS1,
MRS2
t
FSS
t
FSH
FS2
FS1,FS0
FFA/IRA
t
FSS
t
FSH
0,0
t
WFF
(1)
tSKEW1
tENS2
tENH
ENA
tDH
tDS
A0-A35
AEB Offset
AFA Offset
AFB Offset
(Y 2)
AEA Offset
(X 2)
First Word to FIFO1
(X1)
(Y1)
CLKB
1
2
t
WFF
FFB/IRB
4664 drw 07
NOTES:
1. tSKEW1 is the minimum time between the rising CLKA edge and a rising CLKB edge for FFB/IRB to transition HIGH in the next cycle. If the time between the rising edge of CLKA and rising
edge of CLKB is less than tSKEW1, then FFB/IRB may transition HIGH one CLKB cycle later than shown.
2. CSA=LOW, W/RA=HIGH,MBA=LOW. It is not necessary to program offset register on consecutive clock cycles.
Figure 5. Parallel Programming of the Almost-Full Flag and Almost-Empty Flag Offset Values after Reset (IDT Standard and FWFT Modes)
CLKA
4
MRS1,
MRS2
t
FSS
tFSH
FS2
t
WFF
(1)
tSKEW
FFA/IRA
t
SENS
t
FSS
t
SENH
SDH
t
SENS
t
SENH
tSPH
FS1/SEN
tSDS
t
tSDH
tSDS
FS0/SD(3)
AFA Offset (Y1) MSB
AEA Offset (X2) LSB
CLKB
4
t
WFF
4664 drw 08
FFB/IRB
NOTES:
1. tSKEW1 is the minimum time between the rising CLKA edge and a rising CLKB edge for FFB/IRB to transition HIGH in the next cycle. If the time between the rising edge of CLKA and rising
edge of CLKB is less than tSKEW1, then FFB/IRB may transition HIGH one CLKB cycle later than shown.
2. It is not necessary to program offset register bits on consecutive clock cycles. FIFO write attempts are ignored until FFA/IRA and FFB/IRB is set HIGH.
3. Programmable offsets are written serially to the SD input in the order AFA offset (Y1), AEB offset (X1), AFB offset (Y2), and AEA offset (X2).
Figure 6. Serial Programming of the Almost-Full Flag and Almost-Empty Flag Offset Values (IDT Standard and FWFT Modes)
19
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
FFA/IRA HIGH
t
ENH
ENH
t
ENS1
CSA
t
ENS1
t
W/RA
t
ENS2
t
ENH
ENH
MBA
ENA
tENS2
tENH
tENS2
tENS2
tENH
t
tDS
tDH
W1(1)
W2(1)
A0 - A35
No Operation
4664 drw09
NOTE:
1. Written to FIFO1.
Figure 7. Port A Write Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
tCLK
tCLKH
tCLKL
CLKB
FFB/IRB HIGH
tENH
tENS1
CSB
tENH
tENS1
W/RB
tENH
tENS2
MBB
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENB
tDH
t
DS
W1(1)
W2(1)
No Operation
B0-B35
4664 drw 10
NOTE:
1. Written to FIFO2.
DATA SIZE TABLE FOR LONG-WORD WRITES TO FIFO2
SIZE MODE(1)
SIZE
DATA WRITTEN TO FIFO2
DATA READ FROM FIFO2
BM
BE
B35-B27
B26-B18
B17-B9
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
L
X
X
A
B
C
D
A
B
C
D
NOTE:
1. BE is selected at Master Reset: BM and SIZE must be static throughout device operation.
Figure 8. Port B Long-Word Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
20
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
FFB/IRB HIGH
tENH
t
ENS1
ENS1
CSB
t
W/RB
t
ENH
t
ENH
t
ENS2
t
ENS2
ENS2
MBB
t
ENH
t
ENH
t
ENS2
t
ENB
tDH
tDS
B0-B17
4664 drw 11
DATA SIZE TABLE FOR WORD WRITES TO FIFO2
SIZE MODE(1)
WRITE
NO.
DATA WRITTEN
TO FIFO2
DATA READ FROM FIFO2
BM
SIZE
BE
B17-B9
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
1
2
1
2
A
C
C
A
B
D
D
B
H
L
H
A
A
B
C
D
H
L
L
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 9. Port B Word Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
CLKB
FFB/IRB HIGH
tENH
t
ENS1
ENS1
CSB
t
W/RB
MBB
t
ENH
tENH
t
ENS2
ENS2
t
tENH
tENS2
tENH
ENB
tDS
tDH
B0-B8
4664 drw 12
DATA SIZE TABLE FOR BYTE WRITES TO FIFO2
SIZE MODE(1)
WRITE
NO.
DATA WRITTEN
TO FIFO2
DATA READ FROM FIFO2
BM
SIZE
BE
B8-B0
A35-A27
A26-A18
A17-A9
A8-A0
1
2
3
4
1
2
3
4
A
B
C
D
D
C
B
A
H
H
H
H
A
B
C
D
H
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 10. Port B Byte Write Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
21
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
EFB/ORB
HIGH
CSB
W/RB
MBB
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENB
t
MDV
No Operation
W2(1)
tDIS
t
A
t
A
t
EN
W1(1)
W2(1)
Previous Data
B0-B35
(Standard Mode)
t
MDV
tDIS
tA
t
A
OR
tEN
W3(1)
W1(1)
B0-B35
(FWFT Mode)
4664 drw 13
NOTE:
1. Read From FIFO1.
DATA SIZE TABLE FOR FIFO LONG-WORD READS FROM FIFO1
SIZE MODE(1)
SIZE
DATA WRITTEN TO FIFO1
DATA READ FROM FIFO1
BM
BE
A35-A27
A26-A18
A17-A9
A8-A0
B35-B27
B26-B18
B17-B9
B8-B0
L
X
X
A
B
C
D
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation .
Figure 11. Port B Long-Word Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
CLKB
HIGH
EFB/ORB
CSB
W/RB
MBB
ENB
t
ENS2
tENH
No Operation
Read 2
t
MDV
tDIS
t
A
tA
t
EN
B0-B17
Read 1
Read 2
Previous Data
(Standard Mode)
tDIS
t
MDV
OR
t
A
tA
t
EN
B0-B17
(FWFT Mode)
Read 3
Read 1
4664 drw 14
NOTE:
1. Unused word B18-B35 are indeterminate for word-size reads.
DATA SIZE TABLE FOR WORD READS FROM FIFO1
SIZE MODE(1)
DATA WRITTEN TO FIFO1
READ
NO.
DATA READ FROM FIFO1
BM
SIZE
BE
A35-A27
A26-A18
A17-A9
A8-A0
B17-B9
B8-B0
H
L
H
A
B
C
D
1
2
1
2
A
C
C
A
B
D
D
B
H
L
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation .
Figure 12. Port-B Word Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
22
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
EFB/ORB HIGH
CSB
W/RB
MBB
tENS2
tENH
ENB
No Operation
t
DIS
DIS
t
MDV
t
A
t
A
t
A
t
A
t
EN
B0-B8
Read 1
Read 2
Previous Data
Read 3
Read 4
Read 5
(Standard Mode)
t
MDV
t
OR
t
A
tA
tA
t
A
t
EN
B0-B8
Read 1
Read 2
Read 3
Read 4
(FWFT Mode)
4664 drw 15
NOTE:
1. Unused bytes B9-B17, B18-B26, and B27-B35 are indeterminate for byte-size reads.
DATA SIZE TABLE FOR BYTE READS FROM FIFO1
SIZE MODE(1)
DATA WRITTEN TO FIFO1
READ
NO.
DATA READ FROM FIFO1
B8-B0
BM
SIZE
BE
A35-A27
A26-A18
A17-A9
A8-A0
1
2
3
4
1
2
3
4
A
B
C
D
D
C
B
A
H
H
H
H
A
B
C
D
H
L
A
B
C
D
NOTE:
1. BE is selected at Master Reset; BM and SIZE must be static throughout device operation.
Figure 13. Port-B Byte Read Cycle Timing for FIFO1 (IDT Standard and FWFT Modes)
tCLK
tCLKL
tCLKH
CLKA
EFA/ORA HIGH
CSA
W/RA
MBA
tENH
tENH
tENH
tENS2
tENS2
tENS2
ENA
No Operation
W2(1)
t
MDV
t
DIS
DIS
t
A
t
A
t
EN
A0-A35
Previous Data
W1(1)
W2(1)
(Standard Mode)
t
MDV
t
tA
t
A
OR
t
EN
A0-A35
W3(1)
(1)
W1
(FWFT Mode)
4664 drw16
NOTE:
1. Read From FIFO2.
Figure 14. Port-A Read Cycle Timing for FIFO2 (IDT Standard and FWFT Modes)
23
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
CSA
LOW
WRA HIGH
t
ENS2
ENS2
t
ENH
MBA
t
t
ENH
ENA
IRA HIGH
tDS
tDH
A0-A35
W1
t
CLKtCLKL
(1)
tCLKH
tSKEW1
CLKB
ORB
1
2
3
t
REF
tREF
FIFO1 Empty
CSB LOW
W/RB HIGH
LOW
MBB
tENS2
tENH
ENB
tA
Old Data in FIFO1 Output Register
W1
B0-B35
4664 drw17
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for ORB to transition HIGH and to clock the next word to the FIFO1 output register in three CLKB cycles.
If the time between the rising CLKA edge and rising CLKB edge is less than tSKEW1, then the transition of ORB HIGH and load of the first word to the output register may occur one CLKB
cycle later than shown.
2. If Port B size is word or byte, ORB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 15. ORB Flag Timing and First Data Word Fall Through when FIFO1 is Empty (FWFT Mode)
24
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
t
CLK
t
CLKL
t
CLKH
CLKA
CSA
LOW
HIGH
WRA
t
ENS2
t
ENH
ENH
MBA
t
tENS2
ENA
FFA
HIGH
tDS
tDH
A0-A35
W1
t
CLK
(1)
SKEW1
t
CLKH
t
tCLKL
CLKB
1
2
t
REF
t
REF
FIFO1 Empty
LOW
EFB
CSB
W/RB HIGH
LOW
MBB
tENH
tENS2
ENB
tA
W1
B0-B35
4664 drw18
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for EFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then the transition of EFB HIGH may occur one CLKB cycle later than shown.
2. If Port B size is word or byte, EFB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 16. EFB Flag Timing and First Data Read Fall Through when FIFO1 is Empty (IDT Standard Mode)
25
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
CSB
LOW
LOW
W/RB
tENS2
tENH
MBB
ENB
tENH
tENS2
IRB
HIGH
tDH
tDS
B0-B35
W1
t
CLK
(1)
SKEW1
tCLKH
t
CLKL
t
1
2
CLKA
ORA
3
t
REF
tREF
FIFO2 Empty
CSA
LOW
LOW
W/RA
LOW
MBA
ENA
tENS2
tENH
tA
Old Data in FIFO2 Output Register
W1
A0-A35
4664 drw19
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for ORA to transition HIGH and to clock the next word to the FIFO2 output register in three CLKA cycles.
If the time between the CLKB edge and the rising CLKA edge is less than tSKEW1, then the transition of ORA HIGH and load of the first word to the output register may occur one CLKA
cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 17. ORA Flag Timing and First Data Word Fall through when FIFO2 is Empty (FWFT Mode)
26
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
t
CLK
t
CLKL
t
CLKH
CLKB
CSB LOW
LOW
W/RB
tENS2
tENH
MBB
ENB
tENS2
tENH
FFB HIGH
B0-B35
tDH
tDS
W1
(1)
t
CLK
tSKEW1
t
CLKH
t
CLKL
1
2
CLKA
t
REF
t
REF
EFA
FIFO2 Empty
LOW
LOW
LOW
CSA
W/RA
MBA
tENS2
tENH
ENA
tA
W1
A0-A35
4664 drw20
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for EFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW1, then the transition of EFA HIGH may occur one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 18. EFA Flag Timing and First Data Read when FIFO2 is Empty (IDT Standard Mode)
27
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKB
CSB
LOW
W/RB
HIGH
LOW
MBB
tENS2
tENH
ENB
ORB
HIGH
tA
Previous Word in FIFO1 Output Register
Next Word From FIFO1
B0-B35
(1)
tCLK
tSKEW1
tCLKH
tCLKL
1
2
CLKA
t
WFF
t
WFF
FIFO1 Full
LOW
IRA
CSA
HIGH
W/RA
tENH
tENS2
MBA
tENS2
tENH
ENA
tDS
tDH
Write
A0-A35
4664 drw21
To FIFO1
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for IRA to transition HIGH in the next CLKA cycle. If the time between the rising
CLKB edge and rising CLKA edge is less than tSKEW1, then IRA may transition HIGH one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced to the rising CLKB edge that reads the last word or byte write of the long word, respectively.
Figure 19. IRA Flag Timing and First Available Write when FIFO1 is Full (FWFT Mode)
tCLK
tCLKH
tCLKL
CLKB
LOW
CSB
W/RB
MBB
HIGH
LOW
tENS2
tENH
ENB
HIGH
EFB
tA
Previous Word in FIFO1 Output Register
Next Word From FIFO1
B0-B35
(1)
t
CLK tCLKL
tSKEW1
tCLKH
CLKA
1
2
t
WFF
t
WFF
FFA
FIFO1 Full
CSA LOW
W/RA HIGH
t
ENH
t
ENS2
ENS2
MBA
t
tENH
ENA
tDH
tDS
Write
A0-A35
4664 drw22
To FIFO1
NOTES:
1. tSKEW1 is the minimum time between a rising CLKB edge and a rising CLKA edge for FFA to transition HIGH in the next CLKA cycle. If the time between the
rising CLKB edge and rising CLKA edge is less than tSKEW1, then FFA may transition HIGH one CLKA cycle later than shown.
2. If Port B size is word or byte, tSKEW1 is referenced from the rising CLKB edge that reads the last word or byte of the long word, respectively.
Figure 20. FFA Flag Timing and First Available Write when FIFO1 is Full (IDT Standard Mode)
28
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
CSA
LOW
LOW
W/RA
LOW
MBA
tENS2
tENH
ENA
ORA
HIGH
tA
Previous Word in FIFO2 Output Register
SKEW1
Next Word From FIFO2
A0-A35
(1)
tCLK
t
tCLKH
tCLKL
1
2
CLKB
t
WFF
t
WFF
IRB
CSB
FIFO2 FULL
LOW
W/RB
LOW
tENS2
tENH
MBB
ENB
tENS2
tENH
tDS
tDH
Write
B0-B35
4664 drw23
To FIFO2
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for IRB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then IRB may transition HIGH one CLKB cycle later than shown.
2. If Port B size is word or byte, IRB is set LOW by the last word or byte write of the long word, respectively.
Figure 21. IRB Flag Timing and First Available Write when FIFO2 is Full (FWFT Mode)
29
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
tCLK
tCLKH
tCLKL
CLKA
LOW
LOW
LOW
CSA
W/RA
MBA
tENS2
tENH
ENA
EFA
HIGH
tA
Previous Word in FIFO2 Output Register
Next Word From FIFO2
A0-A35
(1)
tCLK
tSKEW1
tCLKH
tCLKL
CLKB
1
2
t
WFF
t
WFF
FIFO2 Full
LOW
FFB
CSB
LOW
W/RB
t
ENS2
ENS2
t
ENH
MBB
ENB
t
t
ENH
tDS
tDH
Write
B0-B35
4664 drw24
To FIFO2
NOTES:
1. tSKEW1 is the minimum time between a rising CLKA edge and a rising CLKB edge for FFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW1, then FFB may transition HIGH one CLKB cycle later than shown.
2. If Port B size is word or byte, FFB is set LOW by the last word or byte write of the long word, respectively.
Figure 22. FFB Flag Timing and First Available Write when FIFO2 is Full (IDT Standard Mode)
30
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
tENS2
tENH
ENA
(1)
tSKEW2
1
2
CLKB
t
PAE
t
PAE
X1 Words in FIFO1
AEB
(X1+1) Words in FIFO1
ENS2
t
t
ENH
ENB
4664 drw 25
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AEB to transition HIGH in the next CLKB cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW2, then AEB may transition HIGH one CLKB cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = LOW, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = HIGH, MBB = LOW). Data in the FIFO1 output register has been read from the FIFO.
3. If Port B size is word or byte, AEB is set LOW by the last word or byte read from FIFO1, respectively.
Figure 23. Timing for AEB when FIFO1 is Almost-Empty (IDT Standard and FWFT Modes)
CLKB
tENS2
tENH
ENB
(1)
tSKEW2
1
2
CLKA
t
PAE
t
PAE
AEA
X2 Words in FIFO2
(X2+1) Words in FIFO2
ENS2
t
tENH
ENA
4664 drw 26
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AEA to transition HIGH in the next CLKA cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW2, then AEA may transition HIGH one CLKA cycle later than shown.
2. FIFO2 Write (CSB = LOW, W/RB = LOW, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW). Data in the FIFO2 output register has been read from the FIFO.
3. If Port B size is word or byte, tSKEW2 is referenced to the rising CLKB edge that writes the last word or byte of the long word, respectively.
Figure 24. Timing for AEA when FIFO2 is Almost-Empty (IDT Standard and FWFT Modes)
(1)
tSKEW2
1
2
CLKA
ENA
tENH
tENS2
t
PAF
t
PAF
(D-Y1) Words in FIFO1
[D-(Y1+1)] Words in FIFO1
AFA
CLKB
tENS2
tENH
ENB
4664 drw 27
NOTES:
1. tSKEW2 is the minimum time between a rising CLKA edge and a rising CLKB edge for AFA to transition HIGH in the next CLKA cycle. If the time between the rising CLKA edge and rising
CLKB edge is less than tSKEW2, then AFA may transition HIGH one CLKA cycle later than shown.
2. FIFO1 Write (CSA = LOW, W/RA = HIGH, MBA = LOW), FIFO1 read (CSB = LOW, W/RB = HIGH, MBB = LOW). Data in the FIFO1 output register has been read from the FIFO.
3. D = Maximum FIFO Depth = 2,048 for the IDT72V3654, 4,096 for the IDT72V3664, 8,192 for the IDT72V3674.
4. If Port B size is word or byte, tSKEW2 is referenced to the rising CLKB edge that reads the last word or byte of the long word, respectively.
Figure 25. Timing for AFA when FIFO1 is Almost-Full (IDT Standard and FWFT Modes)
31
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
(1)
tSKEW2
1
2
CLKB
ENB
tENH
tENS2
t
PAF
t
PAF
(D-Y2) Words in FIFO2
AFB
[D-(Y2+1)] Words in FIFO2
CLKA
tENH
tENS2
ENA
4664 drw 28
NOTES:
1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for AFB to transition HIGH in the next CLKB cycle. If the time between the rising CLKB edge and rising
CLKA edge is less than tSKEW2, then AFB may transition HIGH one CLKB cycle later than shown.
2. FIFO2 write (CSB = LOW, W/RB = LOW, MBB = LOW), FIFO2 read (CSA = LOW, W/RA = LOW, MBA = LOW). Data in the FIFO2 output register has been read from the FIFO.
3. D = Maximum FIFO Depth = 2,048 for the IDT72V3654, 4,096 for the IDT72V3664, 8,192 for the IDT72V3674.
4. If Port B size is word or byte, AFB is set LOW by the last word or byte write of the long word, respectively.
Figure 26. Timing for AFB when FIFO2 is Almost-Full (IDT Standard and FWFT Modes)
CLKA
t
ENH
ENH
t
ENS1
CSA
t
t
ENS1
W/RA
tENH
tENS2
MBA
tENH
tENS2
ENA
tDH
tDS
W1
A0-A35
CLKB
t
PMF
t
PMF
MBF1
CSB
W/RB
MBB
ENB
tENH
tENS2
t
PMR
tEN
t
MDV
tDIS
FIFO1 Output Register
W1 (Remains valid in Mail1 Register after read)
B0-B35
4664 drw29
NOTE:
1. If Port B is configured for word size, data can be written to the Mail1 register using A0-A17 (A18-A35 are don't care inputs). In this first case B0-B17 will have valid data (B18-B35
will be indeterminate). If Port B is configured for byte size, data can be written to the Mail1 Register using A0-A8 (A9-A35 are don't care inputs). In this second case, B0-B8 will
have valid data (B9-B35 will be indeterminate).
Figure 27. Timing for Mail1 Register and MBF1 Flag (IDT Standard and FWFT Modes)
32
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKB
tENH
tENS1
CSB
W/RB
MBB
ENB
t
ENH
t
ENS1
t
ENH
t
ENS2
ENS2
t
t
ENH
t
DH
tDS
W1
B0-B35
CLKA
t
PMF
tPMF
MBF2
CSA
W/RA
MBA
ENA
tENH
tENS2
t
PMR
tEN
tDIS
t
MDV
A0-A35
W1 (Remains valid in Mail 2 Register after read)
FIFO2 Output Register
4664 drw30
NOTE:
1. If Port B is configured for word size, data can be written to the Mail2 Register using B0-B17 (B18-B35 are don’t care inputs). In this first case A0-A17 will have valid data
(A18-A35 will be indeterminate). If Port B is configured for byte size, data can be written to the Mail2 Register using B0-B8 (B9-B35 are don’t care inputs). In this second
case, A0-A8 will have valid data (A9-A35 will be indeterminate).
Figure 28. Timing for Mail2 Register and MBF2 Flag (IDT Standard and FWFT Modes)
33
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
4
1
2
3
2
3
4
1
tENS2
tENH
ENB
RT1
RTM
EFB
t
RSTS
t
RSTH
t
RTMS
t
RTMH
(2)
REF
(2)
tREF
t
tA
B0-Bn
Wx
W1
4664 drw31
NOTES:
1. CSB = LOW
2. Retransmit setup is complete after EFB returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO1.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO1 (Master or Partial) and Retransmit setup. Therefore, FFA will be LOW throughout the Retransmit
setup procedure. D = 2,048, 4,096 and 8,192 for the IDT72V3654, IDT72V3664 and IDT72V3674 respectively.
Figure 29. Retransmit Timing for FIFO1 (IDT Standard Mode)
CLKB
CLKA
4
1
2
3
2
3
4
1
tENS2
tENH
ENA
RT2
RTM
t
RSTS
t
RSTH
t
RTMS
t
RTMH
(2)
REF
(2)
REF
t
t
EFA
A0-An
NOTES:
tA
Wx
W1
4664 drw32
1. CSA = LOW
2. Retransmit setup is complete after EFA returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO2.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO2 (Master or Partial) and Retransmit setup. Therefore, FFB will be LOW throughout the Retransmit
setup procedure. D = 2,048, 4,096 and 8,192 for the IDT72V3654, IDT72V3664 and IDT72V3674 respectively.
Figure 30. Retransmit Timing for FIFO2 (IDT Standard Mode)
34
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
CLKA
CLKB
4
1
2
3
2
3
4
1
LOW
ENB
RT1
t
RSTS
tRSTH
t
RTMS
t
RTMH
RTM
ORB
(2)
REF
(2)
REF
t
t
tA
B0-Bn
Wx
W1
4664 drw33
NOTES:
1. CSB = LOW
2. Retransmit setup is complete after ORB returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO1 after Master Reset on FIFO1.
4. No more than D-2 may be written to the FIFO1 between Reset of FIFO1 (Master or Partial) and Retransmit setup. Therefore, IRA will be LOW throughout the Retransmit
setup procedure. D = 2,049, 4,097 and 8,193 for the IDT72V3654, IDT72V3664 and IDT72V3674 respectively.
Figure 31. Retransmit Timing for FIFO1 (FWFT Mode)
CLKB
CLKA
4
1
2
3
2
3
4
1
LOW
RSTS
ENA
RT2
t
tRSTH
t
RTMS
t
RTMH
RTM
ORA
(2)
REF
(2)
REF
t
t
tA
A0-An
Wx
W1
4664 drw34
NOTES:
1. CSA = LOW
2. Retransmit setup is complete after ORA returns HIGH, only then can a read operation begin.
3. W1 = first word written to the FIFO2 after Master Reset on FIFO2.
4. No more than D-2 may be written to the FIFO2 between Reset of FIFO2 (Master or Partial) and Retransmit setup. Therefore, IRB will be LOW throughout the Retransmit
setup procedure. D = 2,049, 4,097 and 8,193 for the IDT72V3654, IDT72V3664 and IDT72V3674 respectively.
Figure 32. Retransmit Timing for FIFO2 (FWFT Mode)
35
IDT72V3654/72V3664/72V36743.3VCMOSSyncBiFIFOTM WITHBUS-MATCHING
2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
COMMERCIALTEMPERATURERANGE
PARAMETER MEASUREMENT INFORMATION
3.3V
330
Ω
From Output
Under Test
30 pF (1)
510 Ω
PROPAGATION DELAY
LOAD CIRCUIT
3 V
3 V
Timing
Input
1.5 V
High-Level
1.5 V
Input
GND
1.5 V
GND
3 V
t
S
th
tW
3 V
Data,
Enable
Input
1.5 V
1.5 V
Low-Level
1.5 V
1.5 V
GND
Input
GND
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PULSE DURATIONS
3 V
Output
Enable
1.5 V
1.5 V
t
PZL
GND
tPLZ
3 V
≈3 V
Input
1.5 V
1.5 V
1.5 V
Low-Level
Output
GND
V
OL
tPD
t
PZH
tPD
V
OH
V
OH
≈O V
In-Phase
Output
1.5 V
1.5 V
High-Level
Output
1.5 V
V
t
PHZ
OL
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
4664 drw 35
NOTE:
1. Includes probe and jig capacitance.
Figure 33. Output Load and AC Test Conditions
36
ORDERING INFORMATION
IDT
X
XX
X
X
XXXXXX
Device Type Power
Speed
Package
Process/
Temperature
Range
Commercial (0°C to +70°C)
BLANK
PF
Thin Quad Flat Pack (TQFP, PK128-1)
Clock Cycle Time (tCLK
)
10
15
Commercial Only
Low Power
Speed in Nanoseconds
L
72V3654 2,048 x 36 x 2 3.3V SyncBiFIFO with Bus-Matching
72V3664
72V3674
4,096 x 36 x 2 3.3V SyncBiFIFO with Bus-Matching
8,192 x 36 x 2 3.3V SyncBiFIFO with Bus-Matching
4664 drw36
NOTE:
1. Industrial temperature range is available by special order.
DATASHEETDOCUMENTHISTORY
06/13/2000
09/25/2000
12/22/2000
02/08/2001
03/21/2001
11/03/2003
pgs. 1-3, 5, 6, 8-10, 12-14, 16, 19, 20, 23-33, and 37.
pgs. 7, 9, 10 and 37.
pgs. 4, 5 and 13.
pgs. 5 and 12.
pgs. 7 and 8.
pg. 1.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
for Tech Support:
408-360-1753
email:FIFOhelp@idt.com
www.idt.com
37
相关型号:
©2020 ICPDF网 联系我们和版权申明