IDT82V2041E [IDT]
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT; 单信道T1 / E1 / J1短程线路接口单元![IDT82V2041E](http://pdffile.icpdf.com/pdf1/p00116/img/icpdf/IDT82V2041E_634646_icpdf.jpg)
型号: | IDT82V2041E |
厂家: | ![]() |
描述: | SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT |
文件: | 总75页 (文件大小:1372K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
SINGLE CHANNEL T1/E1/J1
SHORT HAUL LINE INTER-
FACE UNIT
IDT82V2041E
FEATURES
•
•
Single channel T1/E1/J1 short haul line interfaces
Supports HPS (Hitless Protection Switching) for 1+1 protection
without external relays
- PRBS (Pseudo Random Bit Sequence) generation and detection
15
with 2 -1 PRBS polynomials for E1
- QRSS(QuasiRandomSequenceSignals)generationanddetection
•
Programmable T1/E1/J1 switchability allowing one bill of ma-
terial for any line condition
20
with 2 -1 QRSS polynomials for T1/J1
- 16-bit BPV (Bipolar Pulse Violation) /Excess Zero/PRBS or QRSS
error counter
- Analog loopback, Digital loopback, Remote loopback and Inband
loopback
Adaptive receive sensitivity up to -20 dB (Host Mode only)
Short circuit protection and internal protection diode for line
drivers
LOS (Loss Of Signal) detection with programmable LOS levels
(Host Mode only)
AIS (Alarm Indication Signal) detection
Supports serial control interface, Motorola and Intel Multiplexed
interfaces and hardware control mode
Pin compatibe to 82V2081 T1/E1/J1 Long Haul/Short Haul LIU
and 82V2051E E1 Short Haul LIU
•
•
Single 3.3 V power supply with 5 V tolerance on digital interfaces
Meets or exceeds specifications in
- ANSI T1.102, T1.403 and T1.408
- ITU I.431, G.703, G.736, G.775 and G.823
- ETSI 300-166, 300-233 and TBR12/13
•
•
- AT&T Pub 62411
•
Software programmable or hardware selectable on:
- Wave-shaping templates
•
- Line terminating impedance (T1:100 Ω, J1:110 Ω, E1:75 Ω/120 Ω)
- Adjustment of arbitrary pulse shape
- JA (Jitter Attenuator) position (receive path or transmit path)
- Single rail/dual rail system interfaces
- B8ZS/HDB3/AMI line encoding/decoding
- Active edge of transmit clock (TCLK) and receive clock (RCLK)
- Active level of transmit data (TDATA) and receive data (RDATA)
- Receiver or transmitter power down
•
•
•
•
Package:
Available in 44-pin TQFP packages
Green package options available
- High impedance setting for line drivers
DESCRIPTION
The IDT82V2041E can be configured as a single channel T1, E1 or J1
Line Interface Unit. The IDT82V2041E performs clock/data recovery, AMI/
B8ZS/HDB3 line decoding and detects and reports the LOS conditions. An
integratedAdaptiveEqualizerisavailabletoincreasethereceivesensitivity
and enable programming of LOS levels. In transmit path, there is an AMI/
B8ZS/HDB3 encoder and Waveform Shaper. There is one Jitter Attenua-
tor, which can be placed in either the receive path or the transmit path. The
Jitter Attenuator can also be disabled. The IDT82V2041E supports both
Single Rail and Dual Rail system interfaces. To facilitate the network main-
tenance, a PRBS/QRSS generation/detection circuit is integrated in the
chip, and different types of loopbacks can be set according to the applica-
tions. Four different kinds of line terminating impedance, 75 Ω, 100 Ω, 110
Ωand120Ωareselectable. Thechipalsoprovidesdrivershort-circuitpro-
tection and internal protection diode. The chip can be controlled by either
software or hardware.
The IDT82V2041E can be used in LAN, WAN, Routers, Wireless Base
Stations, IADs, IMAs, IMAPs, Gateways, Frame Relay Access Devices,
CSU/DSU equipment, etc.
IDT and the IDT logo are trademarks of Integrated Device Technology, Inc.
1
December 9, 2005
2005 Integrated Device Technology, Inc.
DSC-6775/1
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
FUNCTIONAL BLOCK DIAGRAM
LOS/AIS
Detector
LOS
Receiver
Internal
Termination
RCLK
B8ZS/
Data and
Clock
Recovery
Adaptive
Equalizer
RTIP
Data
Slicer
Jitter
Attenuator
RD/RDP
HDB3/AMI
RRING
CV/RDN
Decoder
PRBS Detector
IBLC Detector
Analog
Loopback
Remote
Loopback
Digital
Loopback
TCLK
TD/TDP
TDN
TTIP
B8ZS/
HDB3/AMI
Decoder
Transmitter
Internal
Termination
Jitter
Attenuator
Line
Driver
Waveform
Shaper
TRING
PRBS Generator
IBLC Generator
TAOS
Clock
Generator
Register
Files
Software Control Interface
Pin Control
VDDIO
VDDD
VDDA
VDDT
Figure-1 Block Diagram
Functional Block Diagram
2
December 9, 2005
Table of Contents
1
2
3
IDT82V2041E Pin Configurations ............................................................................................... 8
Pin Description ............................................................................................................................ 9
Functional Description .............................................................................................................. 15
3.1
3.2
3.3
Control Mode Selection .................................................................................................... 15
T1/E1/J1 Mode Selection .................................................................................................. 15
Transmit Path ................................................................................................................... 15
3.3.1 Transmit Path System Interface.............................................................................. 15
3.3.2 Encoder.................................................................................................................. 15
3.3.3 Pulse Shaper .......................................................................................................... 15
3.3.3.1 Preset Pulse Templates .......................................................................... 15
3.3.3.2 User-Programmable Arbitrary Waveform ................................................ 17
3.3.4 Transmit Path Line Interface................................................................................... 20
3.3.5 Transmit Path Power Down .................................................................................... 20
3.4
Receive Path .................................................................................................................... 21
3.4.1 Receive Internal Termination.................................................................................. 21
3.4.2 Line Monitor ............................................................................................................ 22
3.4.3 Adaptive Equalizer.................................................................................................. 23
3.4.4 Receive Sensitivity.................................................................................................. 23
3.4.5 Data Slicer .............................................................................................................. 23
3.4.6 CDR (Clock & Data Recovery)................................................................................ 23
3.4.7 Decoder .................................................................................................................. 23
3.4.8 Receive Path System Interface............................................................................... 24
3.4.9 Receive Path Power Down ..................................................................................... 24
Jitter Attenuator ................................................................................................................ 24
3.5.1 Jitter Attenuation Function Descripton.................................................................... 24
3.5.2 Jitter Attenuator Performance................................................................................. 25
Los And AIS Detection ...................................................................................................... 25
3.6.1 LOS Detection......................................................................................................... 25
3.6.2 AIS Detection.......................................................................................................... 26
Transmit And Detect Internal Patterns .............................................................................. 28
3.7.1 Transmit All Ones ................................................................................................... 28
3.7.2 Transmit All Zeros................................................................................................... 28
3.7.3 PRBS/QRSS Generation And Detection................................................................. 28
Loopback .......................................................................................................................... 28
3.8.1 Analog Loopback .................................................................................................... 28
3.8.2 Digital Loopback ..................................................................................................... 28
3.8.3 Remote Loopback................................................................................................... 28
3.5
3.6
3.7
3.8
Table of Contents
3
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.8.4 Inband Loopback .................................................................................................... 30
3.8.4.1 Transmit Activate/Deactivate Loopback Code......................................... 30
3.8.4.2 Receive Activate/Deactivate Loopback Code.......................................... 30
3.8.4.3 Automatic Remote Loopback .................................................................. 31
Error Detection/Counting And Insertion ............................................................................ 32
3.9.1 Definition Of Line Coding Error............................................................................... 32
3.9.2 Error Detection And Counting................................................................................. 32
3.9.3 Bipolar Violation And PRBS Error Insertion............................................................ 33
3.9
3.10 Line Driver Failure Monitoring ........................................................................................... 33
3.11 MCLK And TCLK .............................................................................................................. 34
3.11.1 Master Clock (MCLK).............................................................................................. 34
3.11.2 Transmit Clock (TCLK) ........................................................................................... 34
3.12 Microcontroller Interfaces ................................................................................................. 35
3.12.1 Parallel Microcontroller Interface ............................................................................ 35
3.12.2 Serial Microcontroller Interface ............................................................................... 35
3.13 Interrupt Handling ............................................................................................................. 35
3.14 5V Tolerant I/O Pins ......................................................................................................... 36
3.15 Reset Operation ................................................................................................................ 36
3.16 Power Supply .................................................................................................................... 36
4
Programming Information ........................................................................................................ 37
4.1
4.2
4.3
Register List And Map ...................................................................................................... 37
Reserved Registers .......................................................................................................... 37
Register Description ......................................................................................................... 38
4.3.1 Control Registers .................................................................................................... 38
4.3.2 Transmit Path Control Registers............................................................................. 40
4.3.3 Receive Path Control Registers.............................................................................. 42
4.3.4 Network Diagnostics Control Registers .................................................................. 44
4.3.5 Interrupt Control Registers...................................................................................... 47
4.3.6 Line Status Registers.............................................................................................. 50
4.3.7 Interrupt Status Registers ....................................................................................... 52
4.3.8 Counter Registers................................................................................................... 54
5
6
7
Hardware Control Pin Summary .............................................................................................. 55
Test Specifications .................................................................................................................... 57
Microcontroller Interface Timing Characteristics ................................................................... 70
7.1
7.2
Serial Interface Timing ...................................................................................................... 70
Parallel Interface Timing ................................................................................................... 71
Table of Contents
4
December 9, 2005
List of Tables
Table-1
Pin Description................................................................................................................ 9
Transmit Waveform Value For E1 75 ohm.................................................................... 17
Transmit Waveform Value For E1 120 ohm.................................................................. 18
Transmit Waveform Value For T1 0~133 ft................................................................... 18
Transmit Waveform Value For T1 133~266 ft............................................................... 18
Transmit Waveform Value For T1 266~399 ft............................................................... 18
Transmit Waveform Value For T1 399~533 ft............................................................... 19
Transmit Waveform Value For T1 533~655 ft............................................................... 19
Transmit Waveform Value For J1 0~655 ft ................................................................... 19
Impedance Matching for Transmitter ............................................................................ 20
Impedance Matching for Receiver ................................................................................ 21
Criteria of Starting Speed Adjustment........................................................................... 25
LOS Declare and Clear ................................................................................................ 26
LOS Declare and Clear Criteria, Adaptive Equalizer Enabled ...................................... 26
AIS Condition ................................................................................................................ 27
Criteria for Setting/Clearing the PRBS_S Bit ................................................................ 28
EXZ Definition ............................................................................................................... 32
Interrupt Event............................................................................................................... 36
Register List and Map ................................................................................................... 37
ID: Device Revision Register ........................................................................................ 38
RST: Reset Register ..................................................................................................... 38
GCF: Global Configuration Register ............................................................................. 38
TERM: Transmit and Receive Termination Configuration Register .............................. 38
JACF: Jitter Attenuation Configuration Register ........................................................... 39
TCF0: Transmitter Configuration Register 0 ................................................................. 40
TCF1: Transmitter Configuration Register 1 ................................................................. 40
TCF2: Transmitter Configuration Register 2 ................................................................. 41
TCF3: Transmitter Configuration Register 3 ................................................................. 41
TCF4: Transmitter Configuration Register 4 ................................................................. 41
RCF0: Receiver Configuration Register 0..................................................................... 42
RCF1: Receiver Configuration Register 1..................................................................... 42
RCF2: Receiver Configuration Register 2..................................................................... 43
MAINT0: Maintenance Function Control Register 0...................................................... 44
MAINT1: Maintenance Function Control Register 1...................................................... 44
MAINT2: Maintenance Function Control Register 2...................................................... 45
MAINT3: Maintenance Function Control Register 3...................................................... 45
MAINT4: Maintenance Function Control Register 4...................................................... 45
MAINT5: Maintenance Function Control Register 5...................................................... 45
MAINT6: Maintenance Function Control Register 6...................................................... 46
INTM0: Interrupt Mask Register 0................................................................................. 47
INTM1: Interrupt Masked Register 1............................................................................. 48
Table-2
Table-3
Table-4
Table-5
Table-6
Table-7
Table-8
Table-9
Table-10
Table-11
Table-12
Table-13
Table-14
Table-15
Table-16
Table-17
Table-18
Table-19
Table-20
Table-21
Table-22
Table-23
Table-24
Table-25
Table-26
Table-27
Table-28
Table-29
Table-30
Table-31
Table-32
Table-33
Table-34
Table-35
Table-36
Table-37
Table-38
Table-39
Table-40
Table-41
List of Tables
5
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-42
Table-43
Table-44
Table-45
Table-46
Table-47
Table-48
Table-49
Table-50
Table-51
Table-52
Table-53
Table-54
Table-55
Table-56
Table-57
Table-58
Table-59
Table-60
Table-61
Table-62
Table-63
Table-64
Table-65
INTES: Interrupt Trigger Edge Select Register............................................................. 49
STAT0: Line Status Register 0 (real time status monitor)............................................. 50
STAT1: Line Status Register 1 (real time status monitor)............................................. 51
INTS0: Interrupt Status Register 0................................................................................ 52
INTS1: Interrupt Status Register 1................................................................................ 53
CNT0: Error Counter L-byte Register 0......................................................................... 54
CNT1: Error Counter H-byte Register 1........................................................................ 54
Hardware Control Pin Summary ................................................................................... 55
Absolute Maximum Rating ............................................................................................ 57
Recommended Operation Conditions........................................................................... 57
Power Consumption...................................................................................................... 58
DC Characteristics ........................................................................................................ 58
E1 Receiver Electrical Characteristics .......................................................................... 59
T1/J1 Receiver Electrical Characteristics...................................................................... 60
E1 Transmitter Electrical Characteristics ...................................................................... 61
T1/J1 Transmitter Electrical Characteristics.................................................................. 62
Transmitter and Receiver Timing Characteristics ......................................................... 63
Jitter Tolerance ............................................................................................................. 64
Jitter Attenuator Characteristics.................................................................................... 67
Serial Interface Timing Characteristics ......................................................................... 70
Multiplexed Motorola Read Timing Characteristics....................................................... 71
Multiplexed Motorola Write Timing Characteristics....................................................... 72
Multiplexed Intel Read Timing Characteristics.............................................................. 73
Multiplexed Intel Write Timing Characteristics .............................................................. 74
List of Tables
6
December 9, 2005
List of Figures
Figure-1
Block Diagram ................................................................................................................. 2
IDT82V2041E TQFP44 Package Pin Assignment .......................................................... 8
E1 Waveform Template Diagram .................................................................................. 16
E1 Pulse Template Test Circuit ..................................................................................... 16
DSX-1 Waveform Template .......................................................................................... 16
T1 Pulse Template Test Circuit ..................................................................................... 16
Receive Monitor Gain Adaptive Equalizer ..................................................................... 21
Transmit/Receive Line Circuit ....................................................................................... 22
Monitoring Receive Line in Another Chip ...................................................................... 22
Monitor Transmit Line in Another Chip .......................................................................... 22
Jitter Attenuator ............................................................................................................. 24
LOS Declare and Clear ................................................................................................. 25
Analog Loopback .......................................................................................................... 29
Digital Loopback ............................................................................................................ 29
Remote Loopback ......................................................................................................... 30
Auto Report Mode ......................................................................................................... 32
Manual Report Mode ..................................................................................................... 33
TCLK Operation Flowchart ............................................................................................ 34
Serial Microcontroller Interface Function Timing ........................................................... 35
Transmit System Interface Timing ................................................................................ 64
Receive System Interface Timing ................................................................................. 64
E1 Jitter Tolerance Performance .................................................................................. 65
T1/J1 Jitter Tolerance Performance .............................................................................. 66
E1 Jitter Transfer Performance ..................................................................................... 68
T1/J1 Jitter Transfer Performance ................................................................................ 69
Serial Interface Write Timing ......................................................................................... 70
Serial Interface Read Timing with SCLKE=1 ................................................................ 70
Serial Interface Read Timing with SCLKE=0 ................................................................ 70
Multiplexed Motorola Read Timing ................................................................................ 71
Multiplexed Motorola Write Timing ................................................................................ 72
Multiplexed Intel Read Timing ....................................................................................... 73
Multiplexed Intel Write Timing ....................................................................................... 74
Figure-2
Figure-3
Figure-4
Figure-5
Figure-6
Figure-7
Figure-8
Figure-9
Figure-10
Figure-11
Figure-12
Figure-13
Figure-14
Figure-15
Figure-16
Figure-17
Figure-18
Figure-19
Figure-20
Figure-21
Figure-22
Figure-23
Figure-24
Figure-25
Figure-26
Figure-27
Figure-28
Figure-29
Figure-30
Figure-31
Figure-32
List of Figures
7
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
1
IDT82V2041E PIN CONFIGURATIONS
34
35
36
37
38
39
40
41
42
43
44
22
21
20
19
18
17
16
15
14
13
12
RD / DS / SCLKE / MONT
IC
VDDT
TRING
TTIP
CS / RXTXM1
INT / RXTXM0
VDDIO
GNDIO
MODE1
MODE0
JA1
GNDT
GNDA
RRING
RTIP
IDT82V2041E
JA0
VDDA
REF
THZ
IC
RST
Figure-2 IDT82V2041E TQFP44 Package Pin Assignment
IDT82V2041E Pin Configurations
8
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
2
PIN DESCRIPTION
Table-1 Pin Description
Name
Type
Pin No.
Description
TTIP
TRING
Analog
output
37
36
TTIP/TRING: Transmit Bipolar Tip/Ring
These pins are the differential line driver outputs. They will be in high impedance state under the following conditions:
•
•
•
•
•
•
THZ pin is high;
THZ bit is set to 1;
Loss of MCLK;
Loss of TCLK (exceptions: Remote Loopback; transmit internal pattern by MCLK);
Transmit path power down;
After software reset; pin reset and power on.
RTIP
RRING
Analog
input
41
40
RTIP/RRING: Receive Bipolar Tip/Ring
These signals are the differential receiver inputs.
TD/TDP
TDN
I
2
3
TD: Transmit Data
When the device is in single rail mode, the NRZ data to be transmitted is input on this pin. Data on TD pin is sampled into the
device on the active edge of TCLK and is encoded by AMI, HDB3 or B8ZS line code rules before being transmitted. In this
mode, TDN should be connected to ground.
TDP/TDN: Positive/Negative Transmit Data
When the device is in dual rail mode, the NRZ data to be transmitted for positive/negative pulse is input on these pins. Data
on TDP/TDN pin is sampled into the device on the active edge of TCLK. The line code in dual rail mode is as follows:
TDP
TDN
Output Pulse
Space
0
0
1
1
0
1
0
1
Positive Pulse
Negative Pulse
Space
TCLK
I
1
TCLK: Transmit Clock input
This pin inputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode transmit clock. The transmit data at TD/TDP or TDN is
sampled into the device on the active edge of TCLK. If TCLK is missing1 and the TCLK missing interrupt is not masked, an inter-
rupt will be generated.
RD/RDP
CV/RDN
O
5
6
RD: Receive Data output
In single rail mode, this pin outputs NRZ data. The data is decoded according to AMI, HDB3 or B8ZS line code rules.
CV: Code Violation indication
In single rail mode, the BPV/CV code violation will be reported by driving the CV pin to high level for a full clock cycle. B8ZS/
HDB3 line code violation can be indicated if the B8ZS/HDB3 decoder is enabled. When AMI decoder is selected, bipolar vio-
lation will be indicated.
In hardware control mode, the EXZ, BPV/CV errors in received data stream are always monitored by the CV pin if single rail
mode is chosen.
RDP/RDN: Positive/Negative Receive Data output
In dual rail mode, this pin outputs the re-timed NRZ data when CDR is enabled, or directly outputs the raw RZ slicer data if CDR
is bypassed.
Active edge and level select:
Data on RDP/RDN or RD is clocked with either the rising or the falling edge of RCLK. The active polarity is also selectable.
Notes:
1. TCLK missing: the state of TCLK continues to be high level or low level over 70 MCLK cycles.
Pin Description
9
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
RCLK
Type
O
Pin No.
4
Description
RCLK: Receive Clock output
This pin outputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode receive clock. Under LOS condition with AIS enabled
(bit AISE=1), RCLK is derived from MCLK. In clock recovery mode, this signal provides the clock recovered from the RTIP/
RRING signal. The receive data (RD in single rail mode or RDP and RDN in dual rail mode) is clocked out of the device on the
active edge of RCLK. If clock recovery is bypassed, RCLK is the exclusive OR (XOR) output of the dual rail slicer data RDP
and RDN. This signal can be used in applications with external clock recovery circuitry.
MCLK
I
9
MCLK: Master Clock input
A built-in clock system that accepts selectable 2.048MHz reference for E1 operating mode and 1.544MHz reference for T1/J1
operating mode. This reference clock is used to generate several internal reference signals:
•
•
•
•
•
Timing reference for the integrated clock recovery unit.
Timing reference for the integrated digital jitter attenuator.
Timing reference for microcontroller interface.
Generation of RCLK signal during a loss of signal condition.
Reference clock to transmit All Ones, all zeros, PRBS/QRSS pattern as well as activate or deactivate Inband Loopback
code if MCLK is selected as the reference clock. Note that for ATAO and AIS, MCLK is always used as the reference
clock.
•
Reference clock during the Transmit All Ones (TAO) condition or sending PRBS/QRSS in hardware control mode.
The loss of MCLK will turn TTIP/TRING into high impedance status.
LOS
REF
O
7
LOS: Loss of Signal Output
This is an active high signal used to indicate the loss of received signal. When LOS pin becomes high, it indicates the loss of
received signal. The LOS pin will become low automatically when valid received signal is detected again. The criteria of loss
of signal are described in 3.6 Los And AIS Detection.
I
I
43
REF: reference resister
An external resistor (3 KΩ, 1%) is used to connect this pin to ground to provide a standard reference current for internal circuit.
MODE1
MODE0
17
16
MODE[1:0]: operation mode of Control interface select
The level on this pin determines which control mode is used to control the device as follows:
MODE[1:0]
Control Interface mode
Hardware interface
00
01
10
11
Serial Microcontroller Interface
Parallel –Multiplexed -Motorola Interface
Parallel –Multiplexed -Intel Interface
•
•
•
The serial microcontroller Interface consists of CS, SCLK, SCLKE, SDI, SDO and INT pins. SCLKE is used for the
selection of the active edge of SCLK.
The parallel multiplexed microcontroller interface consists of CS, AD[7:0], DS/RD, R/W/WR, ALE/AS, ACK/RDY and
INT pins. (refer to 3.12 Microcontroller Interfaces for details)
Hardware interface consists of PULS[3:0], THZ, RCLKE, LP[1:0], PATT[1:0], JA[1:0], MONT, TERM, RPD, MODE[1:0]
and RXTXM[1:0]
RCLKE
I
11
RCLKE: the active edge of RCLK select
In hardware control mode, this pin selects the active edge of RCLK
•
•
L= select the rising edge as the active edge of RCLK
H= select the falling edge as the active edge of RCLK
In software control mode, this pin should be connected to GNDIO.
Pin Description
10
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
Type
I
Pin No.
21
Description
CS
CS: Chip Select
In serial or parallel microcontroller interface mode, this is the active low enable signal. A low level on this pin enables serial or
parallel microcontroller interface.
RXTXM1
RXTXM[1:0]: Receive and transmit path operation mode select
In hardware control mode, these pins are used to select the single rail or dual rail operation modes as well as AMI or HDB3/
B8ZS line coding:
•
•
•
•
00= single rail with HDB3/B8ZS coding
01= single rail with AMI coding
10= dual rail interface with CDR enabled
11= slicer mode (dual rail interface with CDR disabled)
INT
O
20
INT: Interrupt Request
In software control mode, this pin outputs the general interrupt request for all interrupt sources. These interrupt sources can be
masked individually via registers (INTM0, 14H) and (INTM1, 15H). The interrupt status is reported via the registers (INTS0,
19H) and (INTS1, 1AH).
Output characteristics of this pin can be defined to be push-pull (active high or active low) or open-drain (active low) by setting
INT_PIN[1:0] (GCF, 02H).
RXTXM0
SCLK
I
I
RXTXM0
See RXTXM1 above.
25
SCLK: Shift Clock
In serial microcontroller interface mode, this signal is the shift clock for the serial interface. Configuration data on SDI pin is sam-
pled on the rising edge of SCLK. Configuration and status data on SDO pin is clocked out of the device on the falling edge of
SCLK if SCLKE pin is high, or on the rising edge of SCLK if SCLKE pin is low.
ALE
AS
ALE: Address Latch Enable
In parallel microcontroller interface mode with multiplexed Intel interface, the address on AD[7:0] is sampled into the device on
the falling edge of ALE.
AS: Address Strobe
In parallel microcontroller interface mode with multiplexed Motorola interface, the address on AD[7:0] is latched into the device
on the falling edge of AS.
LP1
LP[1:0]: Loopback mode select
When the chip is configured by hardware, this pin is used to select loopback operation modes (Inband Loopback is not provided
in hardware control mode):
•
•
•
•
00= no loopback
01= analog loopback
10= digital loopback
11= remote loopback
SDI
I
24
SDI: Serial Data Input
In serial microcontroller interface mode, this signal is the input data to the serial interface. Configuration data at SDI pin is sam-
pled by the device on the rising edge of SCLK.
WR
WR: Write Strobe
In Intel parallel multiplexed interface mode, this pin is asserted low by the microcontroller to initiate a write cycle. The data on
AD[7:0] is sampled into the device in a write operation.
R/W
R/W: Read/Write Select
In Motorola parallel multiplexed interface mode, this pin is low for write operation and high for read operation.
LP0
LP0
See LP1 above.
Pin Description
11
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
SDO
Type
O
Pin No.
23
Description
SDO: Serial Data Output
In serial microcontroller interface mode, this signal is the output data of the serial interface. Configuration or Status data at SDO
pin is clocked out of the device on the falling edge of SCLK if SCLKE pin is high, or on the rising edge of SCLK if SCLKE pin
is low.
ACK
ACK: Acknowledge Output
In Motorola parallel mode interface, the low level on this pin means:
•
•
The valid information is on the data bus during a read operation.
The write data has been accepted during a write cycle.
RDY
RDY: Ready signal output
In Intel parallel mode interface, the low level on this pin means a read or write operation is in progress; a high acknowledges
a read or write operation has been completed.
TERM
I
I
TERM: Internal or external termination select in hardware mode
This pin selects internal or external impedance matching for both receiver and transmitter.
•
•
0 = ternary interface with external impedance matching network
1 = ternary interface with internal impedance matching network
SCLKE
22
SCLKE: Serial Clock Edge Select
In serial microcontroller interface mode, this signal selects the active edge of SCLK for outputting SDO. The output data is valid
after some delay from the active clock edge. It can be sampled on the opposite edge of the clock. The active clock edge which
clocks the data out of the device is selected as shown below:
SCLKE
Low
SCLK
Rising edge is the active edge.
Falling edge is the active edge.
High
RD: Read Strobe
RD
DS
In Intel parallel multiplexed interface mode, the data is driven to AD[7:0] by the device during low level of RD in a read operation.
DS: Data Strobe
In Motorola parallel multiplexed interface mode, this signal is the data strobe of the parallel interface. In a write operation (R/
W = 0), the data on AD[7:0] is sampled into the device. In a read operation (R/W = 1), the data is driven to AD[7:0] by the device.
MONT: Receive Monitor gain select
In hardware control mode with ternary interface, this pin selects the receive monitor gain of receiver:
0= 0 dB
1= 26 dB
MONT
AD7
I/O
33
AD7: Address/Data Bus bit7
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PULS3
I
PULS[3:0]: these pins are used to select the following functions in hardware control mode:
•
•
•
T1/J1/E1 mode
Transmit pulse template
Internal termination impedance (75Ω/120Ω/100Ω/110Ω)
Refer to 5 Hardware Control Pin Summary for details.
Pin Description
12
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
AD6
Type
I/O
Pin No.
32
Description
AD6: Address/Data Bus bit6
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PULS2
AD5
I
See above.
I/O
31
30
AD5: Address/Data Bus bit5
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PULS1
AD4
I
See above.
I/O
AD4: Address/Data Bus bit4
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PULS0
AD3
I
See above.
I/O
29
28
AD3: Address/Data Bus bit3
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
In Hardware mode, this pin has to be tied to GND.
AD2
I/O
AD2: Address/Data Bus bit2
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
RPD
AD1
I
RPD: Receiver power down control in hardware control mode
•
•
0= normal operation
1= receiver power down
I/O
27
AD1: Address/Data Bus bit1
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PATT1
I
PATT[1:0]: Transmit pattern select
In hardware control mode, this pin selects the transmit pattern
•
•
•
•
00 = normal
01= All Ones
10= PRBS
11= transmitter power down
AD0
I/O
26
AD0: Address/Data Bus bit0
In Intel/Motorola multiplexed interface mode, this signal is the multiplexed bi-directional address/data bus of the microcontroller
interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PATT0
I
See above.
Pin Description
13
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
JA1
Type
I
Pin No.
15
Description
JA[1:0]: Jitter attenuation position, bandwidth and the depth of FIFO select (only used for hardware control mode)
•
•
•
•
00 = JA is disabled
01 = JA in receiver, broad bandwidth, FIFO=64 bits
10 = JA in receiver, narrow bandwidth, FIFO=128 bits
11 = JA in transmitter, narrow bandwidth, FIFO=128 bits
In software control mode, this pin should be connected to ground.
JA0
I
I
14
12
See above.
RST
RST: Hardware reset
The chip is forced to reset state if a low signal is input on this pin for more than 100 ns. MCLK must be active during reset.
THZ
I
13
THZ: Transmitter Driver High Impedance Enable
This signal enables or disables transmitter driver. A low level on this pin enables the driver while a high level on this pin places
driver in high impedance state. Note that the functionality of the internal circuits is not affected by this signal.
Power Supplies and Grounds
3.3 V I/O power supply
VDDIO
GNDIO
VDDT
GNDT
VDDA
GNDA
VDDD
GNDD
-
-
-
-
-
-
-
-
19
18
35
38
42
39
8
I/O ground
3.3 V power supply for transmitter driver
Analog ground for transmitter driver
3.3 V analog core power supply
Analog core ground
Digital core power supply
Digital core ground
10
Others
IC
IC
-
-
34
44
IC: Internal connection
Internal Use. This pin should be left open when in normal operation.
IC: Internal connection
Internal Use. This pin should be connected to ground when in normal operation.
Pin Description
14
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
bit (TCF0, 05H). And the active level of the data on TD/TDP and TDN can
be selected by the TD_INV bit (TCF0, 05H). In hardware control mode, the
falling edge of TCLK and the active high of transmit data are always used.
3
FUNCTIONAL DESCRIPTION
3.1 CONTROL MODE SELECTION
The IDT82V2041E can be configured by software or by hardware. The
software control mode supports Serial Control Interface, Motorola Multi-
plexed Control Interface and Intel Multiplexed Control Interface. The Con-
trol mode is selected by MODE1 and MODE0 pins as follows:
The transmit data from the system side can be provided in two different
ways: Single Rail and Dual Rail. In Single Rail mode, only TD pin is used
for transmitting data and the T_MD[1] bit (TCF0, 05H) should be set to ‘0’.
InDualRailMode,bothTDPpinandTDNpinareusedfortransmittingdata,
the T_MD[1] bit (TCF0, 05H) should be set to ‘1’.
Control Interface mode
3.3.2 ENCODER
00
01
10
11
Hardware interface
In Single Rail mode, when T1/J1 mode is selected, the Encoder can be
selected to be a B8ZS encoder or an AMI encoder by setting T_MD[0] bit
(TCF0, 05H).
Serial Microcontroller Interface.
Parallel –Multiplexed -Motorola Interface
Parallel –Multiplexed -Intel Interface
InSingleRailmode,whenE1modeisselected,theEncodercanbecon-
figured to be a HDB3 encoder or an AMI encoder by setting T_MD[0] bit
(TCF0, 05H).
•
The serial microcontroller Interface consists of CS, SCLK, SCLKE,
SDI, SDO and INT pins. SCLKE is used for the selection of active
edge of SCLK.
The parallel Multiplexed microcontroller Interface consists of CS,
AD[7:0], DS/RD, R/W/WR, ALE/AS, ACK/RDY and INT pins.
Hardware interface consists of PULS[3:0], THZ, RCLKE, LP[1:0],
PATT[1:0], JA[1:0], MONT, TERM, RPD, MODE[1:0] and
RXTXM[1:0]. Refer to 5 Hardware Control Pin Summary for details
about hardware control.
In both T1/J1 mode and E1 mode, when Dual Rail mode is selected (bit
T_MD[1] is ‘1’), the Encoder is by-passed. In Dual Rail mode, a logic ‘1’ on
the TDP pin and a logic ‘0’ on the TDN pin results in a negative pulse on the
TTIP/TRING; a logic ‘0’ on TDP pin and a logic ‘1’ on TDN pin results in a
positive pulse on the TTIP/TRING. If both TDP and TDN are high or low,
the TTIP/TRING outputs a space (Refer to TD/TDP, TDN Pin Description).
•
•
In hardware control mode, the operation mode of receive and transmit
path can be selected by setting RXTXM1 and RXTXM0 pins. Refer to 5
Hardware Control Pin Summary for details.
3.2 T1/E1/J1 MODE SELECTION
When the chip is configured by software, T1/E1/J1 mode is selected by
theT1E1bit(GCF, 02H). InE1application, theT1E1bit(GCF, 02H)should
be set to ‘0’. In T1/J1 application, the T1E1 bit should be set to ‘1’.
3.3.3 PULSE SHAPER
The IDT82V2041E provides two ways of manipulating the pulse shape
before sending it. One is to use preset pulse templates, the other is to use
user-programmable arbitrary waveform template.
When the chip is configured by hardware, T1/E1/J1 mode is selected
by PULS[3:0] pins. These pins also determine transmit pulse template and
internalterminationimpedance.Referto5HardwareControlPinSummary
for details.
In software control mode, the pulse shape can be selected by setting
the related registers.
3.3 TRANSMIT PATH
In hardware control mode, the pulse shape can be selected by setting
PULS[3:0] pins. Refer to 5 Hardware Control Pin Summary for details.
The transmit path of IDT82V2041E consists of an Encoder, an optional
Jitter Attenuator, a Waveform Shaper, a Line Driver and a Programmable
Transmit Termination.
3.3.3.1 PRESET PULSE TEMPLATES
For E1 applications, the pulse shape is shown in Figure-3 according to
the G.703 and the measuring diagram is shown in Figure-4. In internal
impedance matching mode, if the cable impedance is 75 Ω, the PULS[3:0]
bits (TCF1, 06H) should be set to ‘0000’; if the cable impedance is 120 Ω,
the PULS[3:0] bits (TCF1, 06H) should be set to ‘0001’. In external imped-
ance matching mode, for both E1/75 Ω and E1/120 Ω cable impedance,
PULS[3:0] should be set to ‘0001’.
3.3.1 TRANSMIT PATH SYSTEM INTERFACE
The transmit path system interface consists of TCLK pin, TD/TDP pin
andTDNpin.InE1mode,TCLKisa2.048MHzclock.InT1/J1mode,TCLK
is a 1.544 MHz clock. If TCLK is missing for more than 70 MCLK cycles, an
interrupt will be generated if it is not masked.
Transmit data is sampled on the TD/TDP and TDN pins by the active
edgeofTCLK. Theactive edge ofTCLKcanbeselectedby theTCLK_SEL
Functional Description
15
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
grades,andtherearefivepulsetemplatesusedforeachofthecablelength.
The pulse template is selected by PULS[3:0] bits (TCF1, 06H).
1.20
1.00
1.2
1
0.80
0.60
0.8
0.6
0.4
0.2
0
0.40
0.20
0.00
-0.20
-0.6
0.6
-0.4
-0.2
0
0.2
0.4
-0.2
-0.4
-0.6
Tim e in U nit Intervals
Figure-3 E1 Waveform Template Diagram
0
250
500
750
1000
1250
Time (ns)
Figure-5 DSX-1 Waveform Template
TTIP
IDT82V2041E
RLOAD
VOUT
TTIP
TRING
Cable
IDT82V2041E
RLOAD
VOUT
Note: 1. For RLOAD = 75 Ω (nom), Vout (Peak)=2.37V (nom)
2. For RLOAD =120 Ω (nom), Vout (Peak)=3.00V (nom)
TRING
Note: RLOAD = 100 Ω ± 5%
Figure-4 E1 Pulse Template Test Circuit
Figure-6 T1 Pulse Template Test Circuit
For T1 applications, the pulse shape is shown in Figure-5 according to
the T1.102 and the measuring diagram is shown in Figure-6. This also
meets the requirement of G.703, 2001. The cable length is divided into five
For J1 applications, the PULS[3:0] (TCF1, 06H) should be set to ‘0111’.
Table-10 lists these values.
Functional Description
16
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.3.3.2 USER-PROGRAMMABLE ARBITRARY WAVEFORM
(6).Write the scaling data to SCAL[5:0] bits (TCF2, 07H) to scale the
amplitude of the waveform based on the selected standard pulse
amplitude
WhenthePULS[3:0]bitsaresetto‘11xx’, user-programmablearbitrary
waveform generator mode can be used. This allows the transmitter perfor-
mance to be tuned for a wide variety of line condition or special application.
WhenmorethanoneUIisusedtocomposethepulsetemplate,theover-
lap of two consecutive pulses could make the pulse amplitude overflow
(exceed the maximum limitation) if the pulse amplitude is not set properly.
This overflow is captured by DAC_OV_ISbit (INTS1, 1AH), and, if enabled
by the DAC_OV_IM bit (INTM1, 15H), an interrupt will be generated.
Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by
UI[1:0] bits (TCF3, 08H) and each UI is divided into 16 sub-phases,
addressedbytheSAMP[3:0]bits(TCF3,08H).Thepulseamplitudeofeach
phase is represented by a binary byte, within the range from +63 to -63,
stored in WDAT[6:0] bits (TCF4, 09H) in signed magnitude form. The most
positivenumber+63(D)representsthepositivemaximumamplitudeofthe
transmitpulsewhilethemostnegativenumber-63(D)representsthemax-
imum negative amplitude of the transmit pulse. Therefore, up to 64 bytes
are used.
The following tables give all the sample data based on the preset pulse
templates in detail for reference. For preset pulse templates, scaling up/
down against the pulse amplitude is not supported.
1.Table-2 Transmit Waveform Value For E1 75 Ω
2.Table-3 Transmit Waveform Value For E1 120 Ω
There are eight standard templates which are stored in an on-chip ROM.
User can select one of them as reference and make some changes to get
the desired waveform.
3. Table-4 Transmit Waveform Value For T1 0~133 ft
4.Table-5 Transmit Waveform Value For T1 133~266 ft
5.Table-6 Transmit Waveform Value For T1 266~399 ft
6.Table-7 Transmit Waveform Value For T1 399~533 ft
7.Table-8 Transmit Waveform Value For T1 533~655 ft
8.Table-9 Transmit Waveform Value For J1 0~655 ft
User can change the wave shape and the amplitude to get the desired
pulse shape. In order to do this, firstly, users can choose a set of waveform
valuefromthefollowingeighttables,whichisthemostsimilartothedesired
pulse shape. Table-2, Table-3, Table-4, Table-5, Table-6, Table-7, Table-8
and Table-9 list the sample data and scaling data of each of the eight tem-
plates.Thenmodifythecorrespondingsampledatatogetthedesiredtrans-
mit pulse shape.
Table-2 Transmit Waveform Value For E1 75 ohm
Sample
UI 1
UI 2
UI 3
UI 4
1
2
0000000
0000000
0000000
0001100
0110000
0110000
0110000
0110000
0110000
0110000
0110000
0110000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
Secondly, through the value of SCAL[5:0] bits increased or decreased
by 1, the pulse amplitude can be scaled up or down at the percentage ratio
againstthestandardpulseamplitudeifneeded.Fordifferentpulseshapes,
the value of SCAL[5:0] bits and the scaling percentage ratio are different.
The following eight tables list these values.
3
4
5
6
Do the followings step by step, the desired waveform can be pro-
grammed, based on the selected waveform template:
(1).Select the UI by UI[1:0] bits (TCF3, 08H)
7
8
9
(2).Specify the sample address in the selected UI by SAMP [3:0] bits
(TCF3, 08H)
(3).Write sample data to WDAT[6:0] bits (TCF4, 09H). It contains the
data to be stored in the RAM, addressed by the selected UI and the
corresponding sample address.
(4).Set the RW bit (TCF3, 08H) to ‘0’ to implement writing data to RAM,
or to ‘1’ to implement read data from RAM
(5).Implement the Read from RAM/Write to RAM by setting the DONE
bit (TCF3, 08H)
10
11
12
13
14
15
16
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0]
results in 3% scaling up/down against the pulse amplitude.
Repeat the above steps until all the sample data are written to or read
from the internal RAM.
Functional Description
17
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-3 Transmit Waveform Value For E1 120 ohm
Table-5 Transmit Waveform Value For T1 133~266 ft
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
2
0000000
0000000
0000000
0001111
0111100
0111100
0111100
0111100
0111100
0111100
0111100
0111100
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
1
2
0011011
0101110
0101100
0101010
0101001
0101000
0100111
0100110
0100101
1010000
1001111
1001101
1001010
1001000
1000110
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
See Table-4
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
11
12
13
14
15
16
10
11
12
13
14
15
16
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0]
results in 3% scaling up/down against the pulse amplitude.
Table-6 Transmit Waveform Value For T1 266~399 ft
Table-4 Transmit Waveform Value For T1 0~133 ft
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
2
0011111
0110100
0101111
0101100
0101011
0101010
0101001
0101000
0100101
1010111
1010011
1010000
1001011
1001000
1000110
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
See Table-4
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
1
2
0010111
0100111
0100111
0100110
0100101
0100101
0100101
0100100
0100011
1001010
1001010
1001001
1000111
1000101
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
11
12
13
14
15
16
10
11
12
13
14
15
16
SCAL[5:0] = 1101101 (default), One step change of this value of SCAL[5:0]
results in 2% scaling up/down against the pulse amplitude.
1. In T1 mode, when arbitrary pulse for short haul application is configured,
users should write ‘110110’ to SCAL[5:0] bits if no scaling is required.
Functional Description
18
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-7 Transmit Waveform Value For T1 399~533 ft
Table-9 Transmit Waveform Value For J1 0~655 ft
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
2
0100000
0111011
0110101
0101111
0101110
0101101
0101100
0101010
0101000
1011000
1011000
1010011
1001100
1001000
1000110
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
See Table-4
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
1
2
0010111
0100111
0100111
0100110
0100101
0100101
0100101
0100100
0100011
1001010
1001010
1001001
1000111
1000101
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
11
12
13
14
15
16
10
11
12
13
14
15
16
SCAL[5:0] = 110110 (default), One step change of this value of SCAL[5:0]
results in 2% scaling up/down against the pulse amplitude.
Table-8 Transmit Waveform Value For T1 533~655 ft
Sample
UI 1
UI 2
UI 3
UI 4
1
2
0100000
0111111
0111000
0110011
0101111
0101110
0101101
0101100
0101001
1011111
1011110
1010111
1001111
1001001
1000111
1000100
1000011
1000010
1000001
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
See Table-4
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
0000000
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Functional Description
19
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.3.4 TRANSMIT PATH LINE INTERFACE
PULS[3:0] pins will be set to select the specific internal impedance. Refer
to 5 Hardware Control Pin Summary for details.
The transmit line interface consists of TTIP pin and TRING pin. The
impedance matching can be realized by the internal impedance matching
circuit or the external impedance matching circuit. If T_TERM[2] is set to
‘0’, the internal impedance matching circuit will be selected. In this case,
the T_TERM[1:0] bits (TERM, 03H)can beset tochoose 75 Ω, 100 Ω, 110
Ω or 120 Ω internal impedance of TTIP/TRING. If T_TERM[2] is set to ‘1’,
the internal impedance matching circuit will be disabled. In this case, the
external impedance matching circuit will be used to realize the impedance
matching. ForT1/J1 mode, the external impedancematchingcircuit for the
transmitter is not supported. Figure-8showsthe appropriate externalcom-
ponents to connect with the cable. Table-10 is the list of the recommended
impedance matching for transmitter.
TheTTIP/TRINGpinscanalsobeturnedintohighimpedancebysetting
the THZ bit (TCF1, 06H) to ‘1’. In this state, the internal transmit circuits are
still active.
In hardware control mode, TTIP/TRING can be turned into high imped-
ance by pulling THZ pin to high. Refer to 5 Hardware Control Pin Summary
for details.
Besides,inthefollowingcases,bothTTIP/TRINGpinswillalsobecome
high impedance:
•
•
Loss of MCLK;
Loss of TCLK (exceptions: Remote Loopback; Transmit internal
pattern by MCLK);
In hardware control mode, TERM pin can be used to select impedance
matching for both receiver and transmitter. If TERM pin is low, external
impedance network will be used for impedance matching. If TERM pin is
high, internal impedance will be used for impedance matching and
•
•
Transmit path power down;
After software reset; pin reset and power on.
Table-10 Impedance Matching for Transmitter
Cable Configuration
Internal Termination
External Termination
T_TERM[2:0]
PULS[3:0]
RT
T_TERM[2:0]
PULS[3:0]
RT
E1/75 Ω
000
001
010
0000
0001
0010
0011
0100
0101
0110
0111
0 Ω
1XX
0001
0001
-
9.4 Ω
E1/120 Ω
T1/0~133 ft
T1/133~266 ft
T1/266~399 ft
T1/399~533 ft
T1/533~655 ft
J1/0~655 ft
-
-
011
Note: The precision of the resistors should be better than ± 1%
3.3.5 TRANSMIT PATH POWER DOWN
In hardware control mode, the transmit path can be powered down by
pulling both PATT1 and PATT0 pins to high. Refer to 5 Hardware Control
Pin Summary for details.
ThetransmitpathcanbepowereddownbysettingtheT_OFFbit(TCF0,
05H) to ‘1’. In this case, the TTIP/TRING pins are turned into high imped-
ance.
Functional Description
20
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
is set to ‘0’, the internal impedance matching circuit will be selected. In this
case, the R_TERM[1:0] bits (TERM, 03H) can be set to choose 75 Ω, 100
Ω, 110 Ω or 120 Ω internal impedance of RTIP/RRING. If R_TERM[2] is
set to ‘1’, the internal impedance matching circuit will be disabled. In this
case, the external impedance matching circuit will be used to realize the
impedance matching. Figure-8 shows the appropriate external compo-
nents to connect with the cable. Table-11 is the list of the recommended
impedance matching for receiver.
3.4 RECEIVE PATH
The receive path consists of Receive Internal Termination, Monitor
Gain,Amplitude/WaveShapeDetector,DigitalTuningController,Adaptive
Equalizer, Data Slicer, CDR (Clock & Data Recovery), Optional Jitter
Attenuator, Decoder and LOS/AIS Detector. Refer to Figure-7.
3.4.1 RECEIVE INTERNAL TERMINATION
The impedance matching can be realized by the internal impedance
matching circuit or the external impedance matching circuit. If R_TERM[2]
LOS/AIS
LOS
Detector
RCLK
Clock
and Data
Recovery
RTIP
Receive
Internal
termination
Adaptive Equalizer/
Monitor Gain
Jitter
Attenuator
Data Slicer
Decoder
RDP
RDN
RRING
Figure-7 Receive Monitor Gain Adaptive Equalizer
Table-11 Impedance Matching for Receiver
Cable Configuration
Internal Termination
R_TERM[2:0]
External Termination
RR
R_TERM[2:0]
1XX
RR
E1/75 Ω
E1/120 Ω
T1
000
001
010
011
120 Ω
75 Ω
120 Ω
100 Ω
110 Ω
J1
Functional Description
21
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
VDDA
D8
1:1
·
•
•
•
•
RTIP
3.3 V
68µF1
A
•
D7
VDDA
GNDA
4
VDDA
D6
RX Line
RR
0.1µF
0.1µF
·
•
•
•
B
RRING
TTIP
VDDT
D4
D5
2:1
4
RT
•
•
•
·
3.3 V
68µF1
D3
VDDT
GNDT
TX Line
Cp
VDDT
D2
•·
TRING
4
RT
D1
Note: 1. Common decoupling capacitor, one per chip
2. Cp 0-560 (pF)
3. D1 - D8, Motorola - MBR0540T1; International Rectifier - 11DQ04 or 10BQ060
4. RT/ RR: refer to Table-10 and Table-11 respecivley for RT and RR values
Figure-8 Transmit/Receive Line Circuit
In hardware control mode, TERM and PULS[3:0] pins can be used to
select impedance matching for both receiver and transmitter. If TERM pin
is low, external impedance network will be used for impedance matching.
If TERM pin is high, internal impedance will be used for impedance match-
ingandPULS[3:0]pinscanbesettoselectthespecificinternalimpedance.
Refer to 5 Hardware Control Pin Summary for details.
DSX cross connect
point
RTIP
monitor
gain=0dB
RRING
R
normal receive mode
3.4.2 LINE MONITOR
In both T1/J1 and E1 short haul applications, the non-intrusive monitor-
ingonchannelslocatedinotherchipscanbeperformedbytappingthemon-
itored channel through a high impedance bridging circuit. Refer to Figure-
9 and Figure-11.
RTIP
monitor gain
=22/26/32dB
RRING
After a high resistance bridging circuit, the signal arriving at the RTIP/
RRING is dramatically attenuated. To compensate this attenuation, the
Monitor Gain can be used to boost the signal by 22 dB, 26 dB and 32 dB,
selected by MG[1:0] bits (RCF2, 0CH). For normal operation, the Monitor
Gain should be set to 0 dB.
monitor mode
Figure-9 Monitoring Receive Line in Another Chip
DSX cross connect
point
In hardware control mode, MONT pin can be used to set the Monitor
Gain. When MONT pin is low, the Monitor Gain is 0 dB. When MONT pin
ishigh,theMonitorGainis26dB.Referto5HardwareControlPinSummary
for details.
TTIP
TRING
R
normal transmit mode
NotethatLOSindicationisnotsupportedifthedeviceisoperatedinLine
Monitor Mode
RTIP
monitor gain
=22/26/32dB
RRING
monitor mode
Figure-10 Monitor Transmit Line in Another Chip
Functional Description
22
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.4.3 ADAPTIVE EQUALIZER
3.4.4 RECEIVE SENSITIVITY
The Adaptive Equalizer can be enabled to increase the receive sensi-
tivity and to allow programming of the LOS level up to -24 dB. See3.6 Los
And AIS Detection. It can be enabled or disabled by setting EQ_ON bit to
‘1’ or ‘0’ (RCF1, 0BH).
The Receive Sensitivity for both E1 and T1/J1 is -10 dB. With the Adap-
tive Equalizer enabled, the receive sensitivity will be -20 dB.
In Hardware mode, the Adaptive Equalizer can not be enabled and the
receive sensitivity is fixed at -10 dB for both E1 and T1/J1. Refer to 5 Hard-
ware Control Pin Summary for details.
3.4.5 DATA SLICER
The Data Slicer is used to generate a standard amplitude mark or a
space according to the amplitude of the input signals. The threshold can
be40%,50%,60%or70%,asselectedbytheSLICE[1:0]bits(RCF2,0CH).
TheoutputoftheDataSlicerisforwardedtotheCDR(Clock&DataRecov-
ery) unit or to the RDP/RDN pins directly if the CDR is disabled.
3.4.6 CDR (CLOCK & DATA RECOVERY)
TheCDRisusedtorecovertheclockanddatafromthereceivedsignal.
The recovered clock tracks the jitter in the data output from the Data Slicer
and keeps the phase relationship between data and clock during the
absenceoftheincomingpulse.TheCDRcanalsobeby-passedintheDual
Railmode. WhenCDRisby-passed, the data fromtheDataSlicer isoutput
to the RDP/RDN pins directly.
3.4.7 DECODER
In T1/J1 applications, the R_MD[1:0] bits (RCF0, 0AH) is used to select
the AMI decoder or B8ZS decoder. In E1 applications, the R_MD[1:0] bits
(RCF0, 0AH) are used to select the AMI decoder or HDB3 decoder.
Whenthechipisconfiguredbyhardware,theoperationmodeofreceive
and transmit path can be selected by setting RXTXM1 and RXTXM0 pins.
Refer to 5 Hardware Control Pin Summary for details.
Functional Description
23
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.4.8 RECEIVE PATH SYSTEM INTERFACE
3.5 JITTER ATTENUATOR
The receive path system interface consists of RCLK pin, RD/RDP pin
andRDNpin. InE1 mode, the RCLKoutputsarecovered2.048MHzclock.
In T1/J1 mode, the RCLK outputs a recovered 1.544 MHz clock. The
received data is updated on the RD/RDP and RDN pins on the active edge
of RCLK. The active edge of RCLK can be selected by the RCLK_SEL bit
(RCF0, 0AH). And the active level of the data on RD/RDP and RDN can be
selected by the RD_INV bit (RCF0, 0AH).
ThereisoneJitterAttenuatorintheIDT82V2041E.TheJitterAttenuator
can be deployed in the transmit path or the receive path, and can also be
disabled. This is selected by the JACF[1:0] bits (JACF, 04H).
In hardware control mode, Jitter Attenuator position, bandwidth and the
depthofFIFOcanbeselectedbyJA[1:0] pins. Referto 5HardwareControl
Pin Summary for details.
3.5.1 JITTER ATTENUATION FUNCTION DESCRIPTON
In hardware control mode, only the active edge of RCLK can be
selected.IfRCLKEissettohigh,thefallingedgewillbechosenastheactive
edge of RCLK. If RCLKE is set to low, the rising edge will be chosen as the
active edge of RCLK. The active level of the data on RD/RDP and RDN is
the same as that in software control mode.
The Jitter Attenuator is composed of a FIFO and a DPLL, as shown in
Figure-11. The FIFO is used as a pool to buffer the jittered input data, then
the data is clocked out of the FIFO by a de-jittered clock. The depth of the
FIFO can be 32 bits, 64 bits or 128 bits, as selected by the JADP[1:0] bits
(JACF, 04H). In hardware control mode, the depth of FIFO can be selected
byJA[1:0]pins. Referto5HardwareControl PinSummary fordetails. Con-
sequently, the constant delay of the Jitter Attenuator will be 16 bits, 32 bits
or64bits.DeeperFIFOcantoleratelargerjitter,butatthecostofincreasing
data latency time.
Thereceiveddatacanbeoutputtothesystemsideintwodifferentways:
SingleRailorDualRail,asselectedbyR_MDbit[1](RCF0,0AH). InSingle
Rail mode, only RD pin is used to output data and the RDN/CV pin is used
to report the received errors. In Dual Rail Mode, both RDP pin and RDN pin
are used for outputting data.
InthereceiveDualRailmode,theCDRunitcanbeby-passedbysetting
R_MD[1:0] to ‘11’ (binary). In this situation, the output data from the Data
Slicer will be output to the RDP/RDN pins directly, and the RCLK outputs
the exclusive OR (XOR) of the RDP and RDN. This is called receiver slicer
mode. In this case, the transmit path is still operating in Dual Rail mode.
RD/RDP
FIFO
Jittered Data
Jittered Clock
De-jittered Data
RDN
32/64/128
3.4.9 RECEIVE PATH POWER DOWN
The receive path can be powered down by setting R_OFF bit (RCF0,
0AH)to‘1’.Inthiscase,theRCLK,RD/RDP,RDNandLOSwillbelogiclow.
W
R
De-jittered Clock
RCLK
Inhardwarecontrolmode,receiverpowerdowncanbeselectedbypull-
ing RPD pin to high. Refer to 5 Hardware Control Pin Summary for more
details.
DPLL
MCLK
Figure-11 Jitter Attenuator
In E1 applications, the Corner Frequency of the DPLL can be 0.9 Hz or
6.8 Hz, as selected by the JABW bit (JACF, 04H). In T1/J1 applications,
the Corner Frequency of the DPLL can be 1.25 Hz or 5.00 Hz, as selected
bytheJABWbit(JACF,04H).ThelowertheCornerFrequencyis,thelonger
time is needed to achieve synchronization.
When the incoming data moves faster than the outgoing data, the FIFO
will overflow. This overflow is captured by the JAOV_IS bit (INTS1, 1AH).
If the incoming data moves slower than the outgoing data, the FIFO will
underflow.ThisunderflowiscapturedbytheJAUD_IS bit(INTS1,1AH).For
some applications that are sensitive to data corruption, the JA limit mode
can be enabled by setting JA_LIMIT bit (JACF, 04H) to ‘1’. In the JA limit
mode, the speed of the outgoing data will be adjusted automatically when
theFIFOisclosetoitsfulloremptiness.Thecriteriaofstartingspeedadjust-
ment are shown in Table-12. The JA limit mode can reduce the possibility
of FIFO overflow and underflow, but the quality of jitter attenuation is dete-
riorated.
Functional Description
24
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-12 Criteria of Starting Speed Adjustment
LOS=1
FIFO Depth
32 Bits
Criteria for Adjusting Data Outgoing Speed
2 bits close to its full or emptiness
3 bits close to its full or emptiness
4 bits close to its full or emptiness
64 Bits
128 Bits
signal level>P
density=OK
signal level<Q
3.5.2 JITTER ATTENUATOR PERFORMANCE
TheperformanceoftheJitterAttenuatorintheIDT82V2041Emeetsthe
ITU-TI.431,G.703,G.736-739,G.823,G.824,ETSI300011,ETSITBR12/
13, AT&T TR62411 specifications. Details of the Jitter Attenuator perfor-
manceisshowninTable-59JitterToleranceandTable-60JitterAttenuator
Characteristics.
(observing windows= M)
(observing windows= N)
LOS=0
3.6 LOS AND AIS DETECTION
Figure-12 LOS Declare and Clear
LOS detect level threshold
3.6.1 LOS DETECTION
•
With the Adaptive Equalizer off, the amplitude threshold Q is fixed on
800 mVpp, while P=Q+200 mVpp (200 mVpp is the LOS level detect hys-
teresis).
TheLossofSignalDetectormonitorstheamplitudeoftheincomingsig-
nal level and pulse density of the received signal on RTIP and RRING.
•
LOS declare (LOS=1)
With the Adaptive Equalizer on, the value of Q can be selected by
LOS[4:0] bit (RCF1, 0BH), while P=Q+4 dB (4 dB is the LOS level detect
hysteresis). Refer to Table-26 TCF1: Transmitter Configuration Register 1
for LOS[4:0] bit values available.
A LOS is detected when the incoming signal has “no transitions”, i.e.,
when the signal level is less than Q dB below nominal for N consecutive
pulse intervals. Here N is defined by LAC bit (MAINT0, 0DH). LOS will be
declared by pulling LOS pin to high (LOS=1) and LOS interrupt will be gen-
erated if it is not masked.
When the chip is configured by hardware, the Adaptive Equalizer can
notbeenabledandProgrammableLOSlevelsarenotavailable(pin29has
to be set to ‘0’).
NotethatLOSindicationisnotsupportedifthedeviceisoperatedinLine
Monitor Mode. Refer to 3.4.2 Line Monitor.
•
Criteria for declare and clear of a LOS detect
•
LOS clear (LOS=0)
The detection supports ANSI T1.231 and I.431 for T1/J1 mode and
G.775 and ETSI 300233/I.431 for E1 mode. The criteria can be selected
by LAC bit (MAINT0, 0DH) and T1E1 bit (GCF, 02H).
The LOS is cleared when the incoming signal has “transitions”, i.e.,
when the signal level is greater than P dB below nominal and has an aver-
age pulse density of at least 12.5% forM consecutive pulse intervals, start-
ingwiththereceiptofapulse. HereMisdefinedbyLACbit(MAINT0,0DH).
LOS status is cleared by pulling LOS pin to low.
Table-13 and Table-14 summarize LOS declare and clear criteria for
both with and without the Adaptive Equalizer enabled.
•
All Ones output during LOS
Onthesystemside, theRDP/RDNwillreflecttheinputpulse“transition”
at the RTIP/RRING side and output recovered clock (but the quality of the
output clock can not be guaranteed when the input level is lower than the
maximum receive sensitivity) when AISE bit (MAINT0, 0DH) is 0; or output
All Ones as AIS when AISE bit (MAINT0, 0DH) is 1. In this case, RCLK out-
put is replaced by MCLK.
Onthelineside,theTTIP/TRINGwilloutputAllOnesasAISwhenATAO
bit (MAINT0, 0DH) is 1. The All Ones pattern uses MCLK as the reference
clock.
LOS indicator is always active for all kinds of loopback modes.
Functional Description
25
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-13 LOS Declare and Clear
Control bit
LOS declare threshold
LOS clear threshold
T1E1
LAC
Level > 1 Vpp
M=128 bits
12.5% mark density
Level < 800 mVpp
N=175 bits
0=T1.231
<100 consecutive zeroes
1=T1/J1
Level > 1 Vpp
Level < 800 mVpp
N=1544 bits
M=128 bits
12.5% mark density
<100 consecutive zeroes
1=I.431
Level > 1 Vpp
Level < 800 mVpp
N=32 bits
M=32 bits
12.5% mark density
<16 consecutive zeroes
0=G.775
0=E1
Level > 1 Vpp
Level < 800 mVpp
N=2048 bits
M=32 bits
12.5% mark density
<16 consecutive zeroes
1=I.431/ETSI
Table-14 LOS Declare and Clear Criteria, Adaptive Equalizer Enabled
Control bit
LAC
LOS declare threshold
LOS clear threshold
Note
T1E1
LOS[4:0]
00000
00001
T1.231 …
Q (dB)
-4
-6
…
Level > Q+ 4dB
M=128 bits
12.5% mark density
<100 consecutive zeroes
Level < Q
N=175 bits
0
1
01010
01011 - 11111
-24
Reserved
00000
…
-4
1=T1/J1
-
Level > Q+ 4dB
M=128 bits
12.5% mark density
00110
-16
Level < Q
N=1544 bits
I.431 Level detect range is -18 to -30 dB.
00111
-18
...
01010
01011 - 11111
...
<100 consecutive zeroes
I.431
-
-24
Reserved
00000
…
-4
…
-8
Level > Q+ 4dB
M=32 bits
12.5% mark density
<16 consecutive zeroes
00010
Level < Q
N=32 bits
0
1
G.775 Level detect range is -9 to -35 dB.
I.431 Level detect range is -6 to -20 dB.
00011
-10
…
01010
…
G.775
-24
Reserved
0=E1
01011 - 11111
-
00000
-4
Level > Q+ 4dB
M=32 bits
12.5% mark density
<16 consecutive zeroes
00001
…
-6
…
Level < Q
N=2048 bits
I.431/
ETSI 01010
01011 - 11111
-24
Reserved
3.6.2 AIS DETECTION
for declaring/clearing AIS detection are in compliance with the ANSI
T1.231. In E1 applications, the criteria for declaring/clearing AIS detection
comply with the ITU G.775 or the ETSI 300233, as selected by the LAC bit
TheAlarmIndicationSignalcanbedetectedbytheIDT82V2041Ewhen
the Clock & Data Recovery unit is enabled. The status of AIS detection is
reflected in the AIS_S bit (STAT0, 17H). In T1/J1 applications, the criteria
Functional Description
26
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
(MAINT0, 0DH). Table-15 summarizes different criteria for AIS detection
Declaring/Clearing.
Table-15 AIS Condition
ITU G.775 for E1
(LAC bit is set to ‘0’ by default)
ETSI 300233 for E1
(LAC bit is set to ‘1’)
ANSI T1.231 for T1/J1
Less than 3 zeros contained in each of two consecutive Less than 3 zeros contained in a 512-bit Less than 9 zeros contained in an 8192-bit stream
512-bit streams are received stream are received (a ones density of 99.9% over a period of 5.3 ms)
AIS
detected
3 or more zeros contained in each of two consecutive 3 or more zeros contained in a 512-bit 9 or more zeros contained in an 8192-bit stream
AIS
cleared
512-bit streams are received
stream are received
are received
Functional Description
27
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
PRBSdatacanbeinvertedthroughsettingthePRBS_INVbit(MAINT0,
0DH).
3.7 TRANSMIT AND DETECT INTERNAL PATTERNS
The internal patterns (All Ones, All Zeros, PRBS/QRSS pattern and
Activate/Deactivate Loopback Code) will be generated and detected by
IDT82V2041E. TCLK is used as the reference clock by default. MCLK can
alsobe usedasthereferenceclockbysettingthePATT_CLK bit(MAINT0,
0DH) to ‘1’.
Any change of PRBS_S bit will be captured by PRBS_IS bit (INTS0,
19H). The PRBS_IES bit (INTES, 16H) can be used to determine whether
the ‘0’ to ‘1’ change of PRBS_S bit will be captured by the PRBS_IS bit or
any changes of PRBS_S bit will be captured by the PRBS_IS bit. When the
PRBS_ISbitis‘1’,aninterruptwillbegeneratedifthePRBS_IMbit(INTM0,
14H) is set to ‘1’.
If the PATT_CLK bit (MAINT0, 0DH) is set to ‘0’ and the PATT[1:0] bits
(MAINT0,0DH)aresetto‘00’,thetransmitpathwilloperateinnormalmode.
The received PRBS/QRSS logic errors can be counted in a 16-bit
counter if the ERR_SEL [1:0] bits (MAINT6, 13H) are set to ‘00’. Refer to
3.9 Error Detection/Counting And Insertion for the operation of the error
counter.
When the chip is configured by hardware, the transmit path will operate
in normal modeby setting PATT[1:0] pins to ‘00’. Refer to5 Hardware Con-
trol Pin Summary for details.
3.7.1 TRANSMIT ALL ONES
3.8 LOOPBACK
In transmit direction, the All Ones data can be inserted into the data
streamwhenthePATT[1:0]bits(MAINT0,0DH)aresetto‘01’.Thetransmit
datastream is output from TTIP/TRING. In this case, either TCLK orMCLK
can be used as the transmit clock, as selected by the PATT_CLK bit
(MAINT0, 0DH).
To facilitate testing and diagnosis, the IDT82V2041E provides four dif-
ferent loopback configurations: Analog Loopback, Digital Loopback,
Remote Loopback and Inband Loopback.
3.8.1 ANALOG LOOPBACK
Inhardwarecontrolmode,theAllOnesdatacanbeinsertedintothedata
stream in transmit direction by setting PATT[1:0] pins to ‘01’. Refer to 5
Hardware Control Pin Summary for details.
When the ALP bit (MAINT1, 0EH) is set to ‘1’, the chip is configured in
Analog Loopback mode. In thismode, thetransmit signals are looped back
to the Receiver Internal Termination in the receive path then output from
RCLK,RD,RDP/RDN.Atthesametime,thetransmitsignalsarestilloutput
toTTIP/TRINGintransmitdirection.Theall-onespatterncanbegenerated
during analog loopback. Figure-13 shows the process.
3.7.2 TRANSMIT ALL ZEROS
If the PATT_CLK bit (MAINT0, 0DH) is set to ‘1’, the All Zeros will be
inserted into the transmit data stream when the PATT[1:0] bits (MAINT0,
0DH) are set to ‘00’.
3.8.2 DIGITAL LOOPBACK
When the DLP bit (MAINT1, 0EH) is set to ‘1’, the chip is configured in
Digital Loopback mode. In this mode, the transmit signals are looped back
to the jitter attenuator (if enabled) and decoder in receive path, then output
from RCLK, RD, RDP/RDN. At the same time, the transmit signals are still
output to TTIP/TRING in transmit direction. Figure-14 shows the process.
3.7.3 PRBS/QRSS GENERATION AND DETECTION
A PRBS/QRSS will be generated in the transmit direction and detected
20
in the receive direction by IDT82V2041E. The QRSS is 2 -1 for T1/J1
15
applicationsandthePRBSis2 -1forE1applications, withmaximumzero
restrictions according to AT&T TR62411 and ITU-T O.151.
Both Analog Loopback mode and Digital Loopback mode allow the
sending of the internal patterns (All Ones, All Zeros, PRBS, etc.) which will
overwrite the transmit signals. In this case, either TCLK or MCLK can be
used as the reference clock for internal patterns transmission.
When the PATT[1:0] bits (MAINT0, 0DH) are set to ‘10’, the PRBS/
QRSS pattern will be inserted into the transmit data stream with the MSB
first. The PRBS/QRSS pattern will be transmitted directly or invertedly.
In hardware control mode, Digital Loopback can be selected by setting
LP[1:0] pins to ‘10’.
Inhardwarecontrolmode,thePRBSdatawillbegeneratedinthetrans-
mitdirectionandinsertedintothetransmitdatastreambysettingPATT[1:0]
pins to ‘10’. Refer to 5 Hardware Control Pin Summary for details.
3.8.3 REMOTE LOOPBACK
The PRBS/QRSS in the received data stream will be monitored. If the
PRBS/QRSS has reached synchronization status, the PRBS_S bit
(STAT0, 17H)willbesetto‘1’, eveninthepresenceofalogicerrorrateless
When the RLP bit (MAINT1, 0EH) is set to ‘1’, the chip is configured in
RemoteLoopbackmode.Inthismode,therecoveredclockanddataoutput
from Clock and Data Recovery on the receive path is looped back to the
jitterattenuator(ifenabled)andWaveformShaperintransmitpath. Figure-
15 shows the process.
-1
than or equal to 10 . The criteria for setting/clearing the PRBS_S bit are
shown in Table-16.
Inhardwarecontrolmode,RemoteLoopbackcanbeselectedbysetting
LP[1:0] pins to ‘11’.
Table-16 Criteria for Setting/Clearing the PRBS_S Bit
6 or less than 6 bit errors detected in a 64 bits hopping win-
dow.
PRBS/QRSS
Detection
More than 6 bit errors detected in a 64 bits hopping window.
PRBS/QRSS
Missing
Functional Description
28
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
LOS/AIS
Detection
LOS
Receiver
Internal
Termination
B8ZS/
HDB3/AMI
Decoder
Clock and
Data
Recovery
RCLK
RD/RDP
CV/RDN
RTIP
Jitter
Attenuator
Data
Slicer
Adaptive
Equalizer
RRING
Analog
Loopback
B8ZS/
HDB3/AMI
Encoder
Transmitter
Internal
Termination
TTIP
TCLK
TD/TDP
TDN
Line
Driver
Jitter
Attenuator
Waveform
Shaper
TRING
Figure-13 Analog Loopback
LOS/AIS
Detection
LOS
Receiver
Internal
Termination
B8ZS/
HDB3/AMI
Decoder
Clock and
Data
RCLK
RD/RDP
CV/RDN
RTIP
Jitter
Attenuator
Adaptive
Equalizer
Data
Slicer
RRING
Recovery
Digital
Loopback
B8ZS/
HDB3/AMI
Encoder
TTIP
Transmitter
Internal
Termination
TCLK
TD/TDP
TDN
Jitter
Attenuator
Waveform
Shaper
Line
Driver
TRING
Figure-14 Digital Loopback
Functional Description
29
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
LOS/AIS
Detection
LOS
Receiver
Internal
Termination
B8ZS/
HDB3/AMI
Decoder
Clock and
Data
Recovery
RCLK
RD/RDP
CV/RDN
RTIP
Jitter
Attenuator
Data
Slicer
Adaptive
Equalizer
RRING
Remote
Loopback
B8ZS/
HDB3/AMI
Encoder
TTIP
Transmitter
Internal
Termination
TCLK
TD/TDP
TDN
Waveform
Shaper
Jitter
Attenuator
Line
Driver
TRING
Figure-15 Remote Loopback
3.8.4 INBAND LOOPBACK
3.8.4.2 RECEIVE ACTIVATE/DEACTIVATE LOOPBACK CODE
When PATT[1:0] bits (MAINT0, 0DH) are set to ‘11’, the IDT82V2041E
isconfiguredinInbandLoopbackmode.Inthismode,anunframedactivate/
Deactivate Loopback Code is generated repeatedly in transmit direction
per ANSI T1. 403 which overwrite the transmit signals. In receive direction,
theframedorunframedcodeisdetectedperANSIT1.403,eveninthepres-
The pattern of the receive Activate Loopback Code is defined by the
RIBLBA[7:0] bits (MAINT4, 11H). The length of this pattern ranges from 5
bits to 8 bits, as selected by the RIBLBA_L [1:0] bits (MAINT2, 0FH). The
pattern can be programmed to 6-bit-long or 8-bit-long respectively by
repeating itself if it is 3-bit-long or 4-bit-long.
-2
ence of 10 bit error rate.
The pattern of the receive Deactivate Loopback Code is defined by the
RIBLBD[7:0] bits (MAINT5, 12H). The length of the receive Deactivate
Loopback Code ranges from 5 bits to 8 bits, as selected by the
RIBLBD_L[1:0] bits (MAINT2, 0FH). The pattern can be programmed to 6-
bit-long or 8-bit-long respectively by repeating itself if it is 3-bit-long or 4-
bit-long.
If the Automatic Remote Loopback is enabled by setting ARLP bit
(MAINT1, 0EH) to ‘1’, the chip will establish/demolish the Remote Loop-
back based on the reception of the Activate Loopback Code/Deactivate
Loopback Code for 5.1 s. If the ARLP bit (MAINT1, 0EH) is set to ‘0’, the
Remote Loopback can also be demolished forcedly.
AftertheActivateLoopbackCodehasbeendetectedinthereceivedata
for more than 30 ms (in E1 mode) / 40 ms (in T1/J1 mode), the IBLBA_S
bit (STAT0, 17H) will be set to ‘1’ to declare the reception of the Activate
Loopback Code.
3.8.4.1 TRANSMIT ACTIVATE/DEACTIVATE LOOPBACK CODE
The pattern of the transmit Activate/Deactivate Loopback Code is
defined by the TIBLB[7:0] bits (MAINT3, 10H). Whether the code repre-
sentsanActivateLoopbackCodeoraDeactivateLoopbackCodeisjudged
bythefarendreceiver. Thelengthofthepatternrangesfrom5bitsto8bits,
as selected by the TIBLB_L[1:0] bits (MAINT2, 0FH). The pattern can be
programmed to 6-bit-long or 8-bit-long by repeating itself respectively if it
is 3-bit-long or 4-bit-long. When the PATT[1:0] bits (MAINT0, 0DH) are set
to ‘11’, the transmission of the Activate/Deactivate Loopback Code is initi-
ated. If the PATT_CLK bit (MAINT0, 0DH) is set to ‘0’ and the PATT[1:0]
bits (MAINT0, 0DH) are set to ‘00’, the transmission of the Activate/Deac-
tivate Loopback Code will stop.
After the Deactivate Loopback Code has been detected in the receive
dataformorethan30ms(InE1mode)/40ms(InT1/J1mode),theIBLBD_S
bit (STAT0, 17H) will be set to ‘1’ to declare the reception of the Deactivate
Loopback Code.
WhentheIBLBA_IESbit(INTES, 16H)issetto‘0’, onlythe‘0’to‘1’tran-
sition of the IBLBA_S bit will generate an interrupt and set the IBLBA_IS bit
(INTS0, 19H) to ‘1’. When the IBLBA_IES bit is set to ‘1’, any changes of
the IBLBA_S bit will generate an interruptand set theIBLBA_IS bit (INTS0,
19H) to ‘1’. The IBLBA_IS bit will be reset to ‘0’ after being read.
The local transmit activate/deactivate code setting should be the same
as the receive code setting in the remote end. It is the same thing for the
other way round.
WhentheIBLBD_IESbit(INTES, 16H)issetto‘0’, onlythe‘0’to‘1’tran-
sition of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS
bit (INTS0, 19H) to ‘1’. When the IBLBD_IES bit is set to ‘1’, any changes
of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS bit
(INTS0, 19H) to ‘1’. The IBLBD_IS bit will be reset to ‘0’ after being read.
Functional Description
30
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.8.4.3 AUTOMATIC REMOTE LOOPBACK
will still be kept even if the receiver stop receiving the Activate Loopback
Code.
When ARLP bit (MAINT1, 0EH) is set to ‘1’, the IDT82V2041E is con-
figuredintotheAutomaticRemoteLoopbackmode.Inthismode,iftheActi-
vate Loopback Code has been detected in the receive data for more than
5.1s, theRemoteLoopback(shownasFigure-15)willbeestablishedauto-
matically, and the RLP_S bit (STAT1, 18H) will be set to ‘1’ to indicate the
establishment of the Remote Loopback. The IBLBA_S bit (STAT0, 17H) is
set to ‘1’ to generate an interrupt. In this case, the Remote Loopback mode
If the Deactivate Loopback Code has been detected in the receive data
formorethan5.1s,theRemoteLoopbackwillbedemolishedautomatically,
and theRLP_S bit (STAT1, 18H) will set to ‘0’ to indicate the demolishment
oftheRemoteLoopback.TheIBLBD_Sbit(STAT0,17H)issetto‘1’togen-
erate an interrupt.
The Remote Loopback can also be demolished forcedly by setting
ARLP bit (MAINT1, 0EH) to ‘0’.
Functional Description
31
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
•
HDB3/B8ZS Code Violation (CV) Error: In HDB3/B8ZS coding, a
CV error is declared when two consecutive BPV errors are
detected, and the pulses that have the same polarity as the previ-
ous pulse are not the HDB3/B8ZS zero substitution pulses.
Excess Zero (EXZ) Error: There are two standards defining the
EXZ errors: ANSI and FCC. The EXZ_DEF bit (MAINT6, 13H)
chooses which standard will be adopted by the chip to judge the
EXZ error. Table-17 shows definition of EXZ. In hardware control
mode, only ANSI standard is adopted.
3.9 ERROR DETECTION/COUNTING AND INSERTION
3.9.1 DEFINITION OF LINE CODING ERROR
The following line encoding errors can be detected and counted by the
IDT82V2041E:
•
•
Received Bipolar Violation (BPV) Error: In AMI coding, when two
consecutive pulses of the same polarity are received, a BPV error
is declared.
Table-17 EXZ Definition
EXZ Definition
ANSI
FCC
AMI
More than 15 consecutive 0s are detected
More than 3 consecutive 0s are detected
More than 7 consecutive 0s are detected
More than 80 consecutive 0s are detected
More than 3 consecutive 0s are detected
More than 7 consecutive 0s are detected
HDB3
B8ZS
3.9.2 ERROR DETECTION AND COUNTING
Auto Report Mode
(CNT_MD=1)
Which type of the receiving errors (Received CV/BPV errors, excess
zero errors and PRBS logic errors) will be counted is determined by
ERR_SEL[1:0]bits(MAINT6, 13H). Onlyonetypeofreceivingerrorcanbe
counted at a time except that when the ERR_SEL[1:0] bits are set to ‘11’,
both CV/BPV and EXZ errors will be detected and counted.
counting
next second
repeats the
same process
N
Theselectedtypeofreceivingerrorsiscountedinaninternal16-bitError
Counter. Once an error is detected, an error interrupt which is indicated by
corresponding bitin (INTS1, 1AH)willbegenerated ifit isnotmasked. This
Error Counter can be operated in two modes: Auto Report Mode and Man-
ualReportMode, asselectedbytheCNT_MDbit(MAINT6, 13H). InSingle
Rail mode, once BPV or CV errors are detected, the CV pin will be driven
to high for one RCLK period.
One-Second Timer expired?
Y
CNT0, CNT1
counter
data in counter
0
Bit TMOV_IS is set to '1'
• Auto Report Mode
In Auto Report Mode, the internal counter starts to count the received
errorswhentheCNT_MDbit(MAINT6,13H)issetto‘1’.Aone-secondtimer
is used to set the counting period. The received errors are counted within
one second. If the one-second timer expires, the value in the internal
counterwillbetransferredto(CNT0,1BH)and(CNT1,1CH),thentheinter-
nal counter will be reset and start to count received errors for the next sec-
ond.Theerrorsoccurredduringthetransferwillbeaccumulatedtothenext
round. Theexpirationoftheone-secondtimerwillsetTMOV_ISbit(INTS1,
1AH) to‘1’, andwill generateaninterruptiftheTIMER_IMbit(INTM1, 15H)
issetto‘0’.TheTMOV_ISbit(INTS1,1AH)willbeclearedaftertheinterrupt
register is read. The content in the (CNT0, 1BH) and (CNT1, 1CH) should
beread withinthe next second. If thecounter overflows, a counteroverflow
interrupt which is indicated by CNT_OV_IS bit (INTS1, 1AH) will be gener-
ated if it is not masked by CNT_IM bit (INTM1, 15H).
read the data in CNT0, CNT1 within
the next second
Bit TMOV_IS is cleared after
the interrupt register is read
Figure-16 Auto Report Mode
Functional Description
32
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
• Manual Report Mode
3.9.3 BIPOLAR VIOLATION AND PRBS ERROR INSERTION
In Manual Report Mode, the internal Error Counter starts to count the
received errors when the CNT_MD bit (MAINT6, 13H) is set to ‘0’. When
there is a ‘0’ to ‘1’ transition on the CNT_TRF bit (MAINT6, 13H), the data
in the counter will be transferred to (CNT0, 1BH) and (CNT1, 1CH), then
the counter will be reset. The errors occurred during the transfer will be
accumulated to thenext round. If thecounter overflows, a counteroverflow
interrupt indicated by CNT_OV_IS bit (INTS1, 1AH) will be generated if it
is not masked by CNT_IM bit (INTM1, 15H).
Only when three consecutive ‘1’s are detected in the transmit data
stream,willa‘0’to‘1’transitionontheBPV_INSbit(MAINT6,13H)generate
a bipolar violation pulse, and the polarity of the second ‘1’ in the series will
be inverted.
A ‘0’ to ‘1’ transition on the EER_INS bit (MAINT6, 13H) will generate a
logic error during the PRBS/QRSS transmission.
3.10 LINE DRIVER FAILURE MONITORING
Thetransmitdriverfailuremonitorcanbeenabledordisabledbysetting
DFM_OFF bit (TCF1, 06H). If the transmit driver failure monitor is enabled,
the transmit driver failure will be captured by DF_S bit (STAT0, 17H). The
transition of the DF_S bit is reflected by DF_IS bit (INTS0, 19H), and, if
enabled by DF_IMbit(INTM0, 14H), will generate aninterrupt. When there
is a short circuit on the TTIP/TRING port, the output current will be limited
to 100 mA (typical), and an interrupt will be generated.
Manual Report mode
(CNT_MD=0)
counting
N
A '0' to '1' transition
on CNT_TRF?
In hardware control mode, the transmit driver failure monitor is always
enabled.
next round
Y
repeat the
same process
CNT0, CNT1
counter
data in
counter
0
Read the data in CNT0,
CNT1 within next round1
Reset CNT_TRF for the
next '0' to '1' transition
Figure-17 Manual Report Mode
Note: It is recommended that users should do the followings within next round of
error counting: Read the data in CNT0 and CNT1; Reset CNT_TRF bit for
the next ‘0’ to ‘1’ transition on this bit.
Functional Description
33
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.11.2 TRANSMIT CLOCK (TCLK)
3.11 MCLK AND TCLK
TCLK is used to sample the transmit data on TD/TDP and TDN. The
active edge of TCLK can be selected by the TCLK_SEL bit (TCF0, 05H).
During Transmit All Ones, PRBS/QRSS patterns or Inband Loopback
Code, either TCLK or MCLK can be used as the reference clock. This is
selected by the PATT_CLK bit (MAINT0, 0DH).
3.11.1 MASTER CLOCK (MCLK)
MCLK is an independent, free-running reference clock. MCLK is 1.544
MHzforT1/J1applicationsand2.048MHzinE1mode.Thisreferenceclock
is used to generate several internal reference signals:
•
•
•
•
Timing reference for the integrated clock recovery unit.
Timing reference for the integrated digital jitter attenuator.
Timing reference for microcontroller interface.
Generation of RCLK signal during a loss of signal condition if AIS is
enabled.
But for Automatic Transmit All Ones and AIS, only MCLK is used as the
reference clock and the PATT_CLK bit is ignored. In Automatic Transmit
All Ones condition, the ATAO bit (MAINT0, 0DH) is set to ‘1’. In AIS condi-
tion, the AISE bit (MAINT0, 0DH) is set to ‘1’.
•
Reference clock during Transmit All Ones, All Zeros, PRBS/QRSS
pattern and Inband Loopback code if it is selected as the reference
clock. For ATAO and AIS, MCLK is always used as the reference
clock.
Reference clock during Transmit All Ones (TAO) condition or send-
ing PRBS/QRSS in hardware control mode.
If TCLK has been missing for more than 70 MCLK cycles, TCLK_LOS
bit (STAT0, 17H) will be set, and the TTIP/TRING will become high imped-
anceifthechipisnotusedforremoteloopbackorisnotusingMCLKtotrans-
mit internal patterns (TAOS, All Zeros, PRBS and in-band loopback code).
WhenTCLKisdetectedagain,TCLK_LOSbit(STAT0,17H)willbecleared.
The reference frequency to detect a TCLK loss is derived from MCLK.
•
Figure-18 shows the chip operation status in different conditions of
MCLK and TCLK. The missing of MCLK will set the TTIP/TRING to high
impedance state.
Clocked
MCLK=H/L?
yes
clocked
L/H
TCLK status?
generate transmit clock loss
interrupt if not masked in
software control mode;
normal operation
transmitter high impedance
transmitter high impedance
Figure-18 TCLK Operation Flowchart
Functional Description
34
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
3.12.1 PARALLEL MICROCONTROLLER INTERFACE
3.12 MICROCONTROLLER INTERFACES
TheinterfaceiscompatiblewithMotorolaorIntelmicrocontroller.When
MODE[1:0] pins are set to ‘10’, Parallel-Multiplexed-Motorola interface is
selected. When MODE[1:0] pins are set to ‘11’, Parallel-Multiplexed-Intel
Interface is selected.
Themicrocontrollerinterfaceprovidesaccesstoreadandwritethereg-
isters in the device. The chip supports serial microcontroller interface and
two kinds of parallel microcontroller interface: Motorola multiplexed mode
and Intel multiplexed mode. Different microcontroller interfaces can be
selected by setting MODE[1:0] pins to different values. Refer to MODE1
and MODE0 in pin description and Microcontroller Interface Timing Char-
acteristics for details.
3.12.2 SERIAL MICROCONTROLLER INTERFACE
When MODE[1:0] pins are set to‘01’, Serial Interface is selected. In this
mode, the registers are programmed through a 16-bit word which contains
an 8-bit address/command byte (5 address bits A0~A4 and bit R/W) and
an 8-bit data byte (D0~D7). When bit R/W is ‘1’, data is read out from pin
SDO. When bit R/W is ‘0’, data is written into SDI pin. Refer to Figure-19.
CS
SCLK
A0 A1 A2 A3 A4
-
-
R/W
D3
D7
D7
D0
D0
D1
D2
D4 D5 D6
SDI
address/command byte
input data byte (R/W=0)
D2
D4
D1
D3
D5 D6
SDO
output data byte (R/W=1)
Figure-19 Serial Microcontroller Interface Function Timing
remains high impedance
There are totally thirteen kinds of events that could be the interrupt
source:
3.13 INTERRUPT HANDLING
All kinds of interrupt of the IDT82V2041E are indicated by the INT pin.
When the INT_PIN[0] bit (GCF, 02H) is ‘0’, the INT pin is open drain active
low, with a 10 KΩ external pull-up resistor. When the INT_PIN[1:0] bits
(GCF, 02H) are ‘01’, the INT pin is push-pull active low; when the
INT_PIN[1:0] bits are ‘10’, the INT pin is push-pull active high.
(1).LOS Detected
(2).AIS Detected
(3).Driver Failure Detected
(4).TCLK Loss
(5).Synchronization Status of PRBS
(6).PRBS Error Detected
An active level on the INT pin represents an interrupt of the
IDT82V2041E.
(7).Code Violation Received
(8).Excessive Zeros Received
(9).JA FIFO Overflow/Underflow
(10).Inband Loopback Code Status
(11).One-Second Timer Expired
(12).Error Counter Overflow
(13).Arbitrary Waveform Generator Overflow
The interrupt event is captured by the corresponding bit in the Interrupt
Status Register (INTS0, 19H) or (INTS1, 1AH). Every kind of interrupt can
be enabled/disabled individually by the corresponding bit in the register
(INTM0, 14H) or(INTM1, 15H). Someeventisreflectedbythecorrespond-
ing bit in the Status Register (STAT0, 17H) or (STAT1, 18H), and the Inter-
rupt Trigger Edge Selection Register can be used to determine how the
Status Register sets the Interrupt Status Register.
Table-18isasummaryofallkindsofinterruptandtheassociatedStatus
bit, Interrupt Status bit, Interrupt Trigger Edge Selection bit and Interrupt
Mask bit.
AftertheInterruptStatusRegister(INTS0,19H)or(INTS1,1AH)isread,
the INT pin become inactive.
Functional Description
35
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-18 Interrupt Event
Interrupt Event
Status bit
(STAT0, STAT1)
Interrupt Status bit
(INTS0, INTS1)
Interrupt Edge Selection bit
(INTES)
Interrupt Mask bit
(INTM0, INTM1)
LOS Detected
AIS Detected
LOS_S
AIS_S
LOS_IS
AIS_IS
LOS_IES
AIS_IES
LOS_IM
AIS_IM
Driver Failure Detected
DF_S
DF_IS
DF_IES
DF_IM
TCLK Loss
TCLK_LOS
PRBS_S
TCLK_LOS_IS
PRBS_IS
ERR_IS
TCLK_IES
PRBS_IES
TCLK_IM
PRBS_IM
ERR_IM
CV_IM
Synchronization Status of PRBS/QRSS
PRBS/QRSS Error
Code Violation Received
Excessive Zeros Received
JA FIFO Overflow
CV_IS
EXZ_IS
EXZ_IM
JAOV_IS
JAUD_IS
IBLBA_IS
IBLBD_IS
TMOV_IS
CNT_OV_IS
DAC_OV_IS
JAOV_IM
JAUD_IM
IBLBA_IM
IBLBD_IM
TIMER_IM
CNT_IM
JA FIFO Underflow
Inband Loopback Activate Code Status
Inband Loopback Deactivate Code Status
One-Second Timer Expired
Error Counter Overflow
IBLBA_S
IBLBD_S
IBLBA_IES
IBLBD_IES
DAC_OV_IM
Arbitrary Waveform Generator Overflow
MCLK. For T1/J1 operation, bit T1E1(GCF0) is set after reset.
Before accessing any other registers a delay of 50 us is required to
allow the internal clocking to be settled.
3.14 5V TOLERANT I/O PINS
All digital input pins willtolerate5.0 ± 10% voltsand are compatible with
TTL logic.
Afterreset, alldriversoutputareinhighimpedancestate, alltheinternal
flip-flops are reset, and all the registers are initialized to default values.
When performing a software reset, the T1E1 bit (GCF0) will not be reset
and stay with the set value.
3.15 RESET OPERATION
The chip can be reset in two ways:
•
•
Software Reset: Writing to the RST register (01H) will reset the chip
in 1 us.
Hardware Reset: Asserting the RST pin low for a minimum of 100
ns will reset the chip.
3.16 POWER SUPPLY
This chip uses a single 3.3 V power supply.
During Hardware Reset, the device requires an active clock on
Functional Description
36
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4
PROGRAMMING INFORMATION
4.1 REGISTER LIST AND MAP
4.2 RESERVED REGISTERS
The registers banks include control registers, status registers and
counter registers.
When writing to registers with reserved bit locations, the default state
must be written to the reserved bits to ensure proper device operation.
Table-19 Register List and Map
Address (hex)
Register
R/W
Map
b7
b6
b5
b4
b3
b2
b1
b0
Control Registers
00
01
02
03
04
ID
R
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RST
W
GCF
TERM
JACF
R/W
R/W
R/W
-
-
-
-
-
-
-
-
-
T1E1
R_TERM2
JADP1
INT_PIN1
R_TERM1
JADP0
INT_PIN0
R_TERM0
JABW
T_TERM2
JA_LIMIT
T_TERM1
JACF1
T_TERM0
JACF0
Transmit Path Control Registers
05
06
07
08
09
TCF0
TCF1
TCF2
TCF3
TCF4
R/W
R/W
R/W
R/W
R/W
-
-
-
T_OFF
THZ
TD_INV
PULS3
SCAL3
SAMP3
WDAT3
TCLK_SEL
PULS2
T_MD1
PULS1
SCAL1
SAMP1
WDAT1
T_MD0
PULS0
SCAL0
SAMP0
WDAT0
-
-
-
DFM_OFF
SCAL5
UI1
-
DONE
-
SCAL4
UI0
SCAL2
RW
SAMP2
WDAT2
WDAT6
WDAT5
WDAT4
Receive Path Control Registers
0A
0B
0C
RCF0
RCF1
RCF2
R/W
R/W
R/W
-
-
-
-
-
R_OFF
LOS4
RD_INV
LOS3
-
RCLK_SEL
R_MD1
LOS1
MG1
R_MD0
LOS0
MG0
EQ_ON
-
-
LOS2
-
SLICE1
SLICE0
Network Diagnostics Control Registers
0D
0E
0F
10
11
MAINT0
MAINT1
MAINT2
MAINT3
MAINT4
MAINT5
MAINT6
R/W
R/W
R/W
R/W
R/W
R/W
R/W
-
PATT1
-
PATT0
-
PATT_CLK
-
PRBS_INV
ARLP
LAC
RLP
AISE
ALP
ATAO
DLP
-
-
-
TIBLB_L1
TIBLB5
RIBLBA5
RIBLBD5
ERR_INS
TIBLB_L0
TIBLB4
RIBLBA_L1 RIBLBA_L0 RIBLBD_L1 RIBLBD_L0
TIBLB7
RIBLBA7
RIBLBD7
-
TIBLB6
RIBLBA6
RIBLBD6
BPV_INS
TIBLB3
RIBLBA3
RIBLBD3
ERR_SEL1
TIBLB2
RIBLBA2
RIBLBD2
ERR_SEL0
TIBLB1
RIBLBA1
RIBLBD1
CNT_MD
TIBLB0
RIBLBA0
RIBLBD0
CNT_TRF
RIBLBA4
RIBLBD4
EXZ_DEF
12
13
Interrupt Control Registers
14
INTM0
R/W
-
IBLBA_IM
IBLBD_IM
JAUD_IM
PRBS_IM
ERR_IM
TCLK_IM
EXZ_IM
DF_IM
CV_IM
DF_IES
AIS_IM
TIMER_IM
AIS_IES
LOS_IM
CNT_IM
LOS_IES
15
INTM1
INTES
R/W DAC_OV_IM JAOV_IM
16
R/W
-
IBLBA_IES IBLBD_IES PRBS_IES
TCLK_IES
Line Status Register
17
18
STAT0
STAT1
R
R
-
-
IBLBA_S
-
IBLBD_S
RLP_S
PRBS_S
-
TCLK_LOS
-
DF_S
-
AIS_S
-
LOS_S
-
Interrupt Status Register
19
INTS0
R
R
-
IBLBA_IS
IBLBD_IS
JAUD_IS
PRBS_IS TCLK_LOS_IS
DF_IS
CV_IS
AIS_IS
LOS_IS
1A
INTS1
DAC_OV_IS JAOV_IS
ERR_IS
EXZ_IS
TMOV_IS CNT_OV_IS
Counter Registers
1B
1C
CNT0
CNT1
R
R
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit9
Bit0
Bit8
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Programming Information
37
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3 REGISTER DESCRIPTION
4.3.1 CONTROL REGISTERS
Table-20 ID: Device Revision Register
(R, Address = 00H)
Symbol
Bit
Default
Description
Description
ID[7:0]
7-0
00H
Current silicon chip ID.
Table-21 RST: Reset Register
(W, Address = 01H)
Symbol
Bit
Default
RST[7:0]
7-0
00H
Software reset. A write operation on this register will reset all internal registers to their default values, and the status
of all ports are set to the default status. The content in this register can not be changed. After reset, all drivers output
are in high impedance state.
Note: Bit T1E1 (GCF0) will keep set value and will not be reset.
Table-22 GCF: Global Configuration Register
(R/W, Address = 02H)
Symbol
-
Bit
7-3
2
Default
00000
0
Description
Reserved.
T1E1
This bit selects the E1 or T1/J1 operation mode globally.
= 0: E1 mode is selected.
= 1: T1/J1 mode is selected.
Note: After bit T1E1 is changed: Before accessing any other regisers a delay of 50us is required to allow the internal clocking
to be settled.
INT_PIN[1:0]
1-0
00
Interrupt pin control
= x0: Open drain, active low (with an external pull-up resistor)
= 01: Push-pull, active low
= 11: Push-pull, active high
Table-23 TERM: Transmit and Receive Termination Configuration Register
(R/W, Address = 03H)
Symbol
Bit
7-6
5-3
Default
00
Description
-
Reserved.
T_TERM[2:0]
000
These bits select the internal termination for transmit line impedance matching.
= 000: Internal 75 Ω impedance matching
= 001: Internal 120 Ω impedance matching
= 010: Internal 100 Ω impedance matching
= 011: Internal 110 Ω impedance matching
= 1xx: Selects external impedance matching resistors for E1 mode only. T1/J1 does not require external impedance
resistors (see Table-10).
R_TERM[2:0]
2-0
000
These bits select the internal termination for receive line impedance matching.
= 000: Internal 75 Ω impedance matching
= 001: Internal 120 Ω impedance matching
= 010: Internal 100 Ω impedance matching
= 011: Internal 110 Ω impedance matching
= 1xx: Selects external impedance matching resistors (see Table-11).
Programming Information
38
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-24 JACF: Jitter Attenuation Configuration Register
(R/W, Address = 04H)
Symbol
-
Bit
7-6
5
Default
Description
00
1
Reserved.
JA_LIMIT
= 0: Normal mode
= 1: JA limit mode
JACF[1:0]
JADP[1:0]
JABW
4-3
2-1
0
00
00
0
Jitter attenuation configuration
= 00/10: JA not used
= 01: JA in transmit path
= 11: JA in receive path
Jitter attenuation depth select
= 00: 128 bits
= 01: 64 bits
= 1x: 32 bits
Jitter transfer function bandwidth select
= 0: 6.8 Hz (E1)
5 Hz (T1/J1)
= 1: 0.9 Hz (E1)
1.25 Hz (T1/J1)
Programming Information
39
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.2 TRANSMIT PATH CONTROL REGISTERS
Table-25 TCF0: Transmitter Configuration Register 0
(R/W, Address = 05H)
Symbol
-
Bit
7-5
4
Default
000
Description
Reserved.
T_OFF
0
Transmitter power down enable
= 0: Transmitter power up
= 1: Transmitter power down (line driver high impedance)
TD_INV
TCLK_SEL
T_MD[1:0]
3
2
0
0
Transmit data invert
= 0: Data on TD or TDP/TDN is active high
= 1: Data on TD or TDP/TDN is active low
Transmit clock edge select
= 0: Data on TDP/TDN is sampled on the falling edge of TCLK
= 1: Data on TDP/TDN is sampled on the rising edge of TCLK
0-1
00
Transmitter operation mode control
T_MD[1:0] select different stages of the transmit data path
= 00: Enable HDB3/B8ZS encoder and waveform shaper blocks. Input on pin TD is single rail NRZ data
= 01: Enable AMI encoder and waveform shaper blocks. Input on pin TD is single rail NRZ data
= 1x: Encoder is bypassed, dual rail NRZ transmit data input on pin TDP/TDN
Table-26 TCF1: Transmitter Configuration Register 1
(R/W, Address = 06H)
Symbol
-
Bit
7-6
5
Default
Description
00
0
Reserved. This bit should be ‘0’ for normal operation.
DFM_OFF
Transmit driver failure monitor disable
= 0: DFM is enabled
= 1: DFM is disabled
THZ
4
1
Transmit line driver high impedance enable
= 0: Normal state
= 1: Transmit line driver high impedance enable (other transmit path still work normally)
PULS[3:0]
3-0
0000 These bits select the transmit template:
T1/E1/J1
TCLK
Cable impedance
Cable range
-
Allowable Cable loss
0-24 dB
00001
0001
E1
2.048 MHz
75 Ω
E1
2.048 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
120 Ω
100 Ω
100 Ω
100 Ω
100 Ω
100 Ω
110 Ω
Reserved
-
0-24 dB
0-0.6 dB
0010
DSX1
DSX1
DSX1
DSX1
DSX1
J1
0-133 ft
0011
133-266 ft
266-399 ft
399-533 ft
533-655 ft
0-655 ft
0.6-1.2 dB
1.2-1.8 dB
1.8-2.4 dB
2.4-3.0 dB
0-3.0 dB
0100
0101
0110
0111
1000 - 1011
11XX
User programmable waveform setting
1. In internal impedance matching mode, for E1/75 Ω cable impedance, the PULS[3:0] bits (TCF1, 06H) should be set to ‘0000’. In external impedance matching mode, for E1/75 Ω cable
impedance, the PULS[3:0] bits should be set to ‘0001’.
Programming Information
40
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-27 TCF2: Transmitter Configuration Register 2
(R/W, Address = 07H)
Symbol
-
Bit
7-6
5-0
Default
00
Description
Reserved.
SCAL[5:0]
100001
SCAL specifies a scaling factor to be applied to the amplitude of the user-programmable arbitrary pulses which is
to be transmitted if needed. The default value of SCAL[5:0] is ‘100001’. Refer to 3.3.3.2 User-Programmable Arbi-
trary Waveform.
= 110110: Default value for T1 0~133 ft, T1 133~266 ft, T1 266~399 ft, T1 399~533 ft, T1 533~655 ft, J1 0~655 ft.
One step change of this value results in 2% scaling up/down against the pulse amplitude.
= 100001: Default value for E1 75 Ω and 120 Ω. One step change of this value results in 3% scaling up/down
against the pulse amplitude.
t
Table-28 TCF3: Transmitter Configuration Register 3
(R/W, Address = 08H)
Symbol
DONE
RW
Bit
7
Default
Description
0
0
After ‘1’ is written to this bit, a read or write operation is implemented.
6
This bit selects read or write operation
= 0: Write to RAM
= 1: Read from RAM
UI[1:0]
5-4
3-0
00
These bits specify the unit interval address. There are totally 4 unit intervals.
= 00: UI address is 0 (The most left UI)
= 01: UI address is 1
= 10: UI address is 2
= 11: UI address is 3
SAMP[3:0]
0000
These bits specify the sample address. Each UI has totally 16 samples.
= 0000: Sample address is 0 (The most left sample)
= 0001: Sample address is 1
= 0010: Sample address is 2
……
= 1110: Sample address is 14
= 1111: Sample address is 15
Table-29 TCF4: Transmitter Configuration Register 4
(R/W, Address = 09H)
Symbol
-
Bit
7
Default
Description
0
Reserved
WDAT[6:0]
6-0
0000000 In Indirect Write operation, the WDAT[6:0] will be loaded to the pulse template RAM, specifying the amplitude of
the Sample.
After an Indirect Read operation, the amplitude data of the Sample in the pulse template RAM will be output to the
WDAT[6:0].
Programming Information
41
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.3 RECEIVE PATH CONTROL REGISTERS
Table-30 RCF0: Receiver Configuration Register 0
(R/W, Address = 0AH)
Symbol
-
Bit
7-5
4
Default
000
Description
Reserved
R_OFF
0
Receiver power down enable
= 0: Receiver power up
= 1: Receiver power down
RD_INV
RCLK_SEL
R_MD[1:0]
3
2
0
0
Receive data invert
= 0: Data on RD or RDP/RDN is active high
= 1: Data on RD or RDP/RDN is active low
Receive clock edge select (this bit is ignored in slicer mode)
= 0: Data on RD or RDP/RDN is updated on the rising edge of RCLK
= 1: Data on RD or RDP/RDN is updated on the falling edge of RCLK
1-0
00
Receive path decoding selection
= 00: Receive data is HDB3 (E1)/B8ZS (T1/J1) decoded and output on RD pin with single rail NRZ format
= 01: Receive data is AMI decoded and output on RD pin with single rail NRZ format
= 10: Decoder is bypassed, re-timed dual rail data with NRZ format output on RDP/RDN (dual rail mode with clock
recovery)
= 11: CDR and decoder are bypassed, slicer data with RZ format output on RDP/RDN (slicer mode)
Table-31 RCF1: Receiver Configuration Register 1
(R/W, Address= 0BH)
Symbol
-
Bit
7
Default
Description
0
0
Reserved
EQ_ON
6
= 0: Receive equalizer off
= 1: Receive equalizer on (LOS programming enabled)
-
5
0
Reserved.
LOS[4:0]
4:0
10101
LOS Clear Level (dB)
LOS Declare Level (dB)
00000
00001
0
<-4
>-2
<-6
00010
>-4
<-8
00011
>-6
<-10
<-12
<-14
<-16
<-18
<-20
<-22
<-24
00100
>-8
00101
>-10
>-12
>-14
>-16
>-18
>-20
Reserved
00110
00111
01000
01001
01010
01011 - 11111
Programming Information
42
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-32 RCF2: Receiver Configuration Register 2
(R/W, Address = 0CH)
Symbol
-
Bit
7-6
5-4
Default
00
Description
Reserved.
SLICE[1:0]
01
Receive slicer threshold
= 00: The receive slicer generates a mark if the voltage on RTIP/RRING exceeds 40% of the peak amplitude.
= 01: The receive slicer generates a mark if the voltage on RTIP/RRING exceeds 50% of the peak amplitude.
= 10: The receive slicer generates a mark if the voltage on RTIP/RRING exceeds 60% of the peak amplitude.
= 11: The receive slicer generates a mark if the voltage on RTIP/RRING exceeds 70% of the peak amplitude.
-
3-2
1-0
10
00
Reserved
MG[1:0]
Monitor gain setting: these bits select the internal linear gain boost
= 00: 0 dB
= 01: 22 dB
= 10: 26 dB
= 11: 32 dB
Programming Information
43
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.4 NETWORK DIAGNOSTICS CONTROL REGISTERS
Table-33 MAINT0: Maintenance Function Control Register 0
(R/W, Address = 0DH)
Symbol
-
Bit
7
Default
00
Description
Reserved.
PATT[1:0]
6-5
00
These bits select the internal pattern and insert it into transmit data stream.
= 00: Normal operation (PATT_CLK = 0) / insert all zeros (PATT_CLK = 1)
= 01: Insert All Ones
= 10: Insert PRBS (E1: 215-1) or QRSS (T1/J1: 220-1)
= 11: Insert programmable Inband loopback activate or deactivate code (default value 00001)
PATT_CLK
PRBS_INV
LAC
4
3
2
1
0
0
0
0
0
0
Selects reference clock for transmitting internal pattern
= 0: Uses TCLK as the reference clock
= 1: Uses MCLK as the reference clock
Inverts PRBS
= 0: The PRBS data is not inverted
= 1: The PRBS data is inverted before transmission and detection
LOS/AIS criterion is selected as below:
= 0: G.775 (E1) / T1.231 (T1/J1)
= 1: ETSI 300233& I.431 (E1) / I.431 (T1/J1)
AISE
AIS enable during LOS
= 0: AIS insertion on RDP/RDN/RCLK is disabled during LOS
= 1: AIS insertion on RDP/RDN/RCLK is enabled during LOS
ATAO
Automatically Transmit All Ones (enabled only when PATT[1:0] = 00)
= 0: Disabled
= 1: Automatically Transmit All Ones pattern at TTIP/TRING during LOS
Table-34 MAINT1: Maintenance Function Control Register 1
(R/W, Address= 0EH)
Symbol
-
Bit
7-4
3
Default
0000
0
Description
Reserved
ARLP
Automatic remote loopback enable
= 0: Disables automatic remote loopback (normal transmit and receive operation)
= 1: Enables automatic remote loopback
RLP
ALP
DLP
2
1
0
0
0
0
Remote loopback enable
= 0: Disables remote loopback (normal transmit and receive operation)
= 1: Enables remote loopback
Analog loopback enable
= 0: Disables analog loopback (normal transmit and receive operation)
= 1: Enables analog loopback
Digital loopback enable
= 0: Disables digital loopback (normal transmit and receive operation)
= 1: Enables digital loopback
Programming Information
44
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-35 MAINT2: Maintenance Function Control Register 2
(R/W, Address = 0FH)
Symbol
Bit
7-6
5-4
Default
00
Description
-
Reserved
TIBLB_L[1:0]
00
Defines the length of the user-programmable transmit loopback activate/deactivate code contained in TIBLB reg-
ister. The default selection is 5 bits length.
= 00: 5-bit long activate code in TIBLB [4:0]
= 01: 6-bit long activate code in TIBLB [5:0]
= 10: 7-bit long activate code in TIBLB [6:0]
= 11: 8-bit long activate code in TIBLB [7:0]
RIBLBA_L[1:0]
RIBLBD_L[1:0]
3-2
1-0
00
01
Defines the length of the user-programmable receive activate loopback code contained in RIBLBA register. The
default selection is 5 bits length.
= 00: 5-bit long activate code in RIBLBA [4:0]
= 01: 6-bit long activate code in RIBLBA [5:0]
= 10: 7-bit long activate code in RIBLBA [6:0]
= 11: 8-bit long activate code in RIBLBA [7:0]
Defines the length of the user-programmable receive deactivate loopback code contained in RIBLBD register. The
default selection is 6 bits length.
= 00: 5-bit long deactivate code in RIBLBD [4:0]
= 01: 6-bit long deactivate code in RIBLBD [5:0]
= 10: 7-bit long deactivate code in RIBLBD [6:0]
= 11: 8-bit long deactivate code in RIBLBD [7:0]
Table-36 MAINT3: Maintenance Function Control Register 3
(R/W, Address = 10H)
Symbol
Bit
Default
Description
TIBLB[7:0]
7-0
(000)00001 Defines the user-programmable transmit Inband loopback activate or deactivate code. The default selection is
00001.
TIBLB [7:0] form the 8-bit repeating code
TIBLB [6:0] form the 7-bit repeating code
TIBLB [5:0] form the 6-bit repeating code
TIBLB [4:0] form the 5-bit repeating code
Table-37 MAINT4: Maintenance Function Control Register 4
(R/W, Address = 11H)
Symbol
Bit
Default
Description
RIBLBA[7:0]
7-0
(000)00001 Defines the user-programmable receive Inband loopback activate code. The default selection is 00001.
RIBLBA [7:0] form the 8-bit repeating code
RIBLBA [6:0] form the 7-bit repeating code
RIBLBA [5:0] form the 6-bit repeating code
RIBLBA [4:0] form the 5-bit repeating code
Table-38 MAINT5: Maintenance Function Control Register 5
(R/W, Address = 12H)
Symbol
Bit
Default
Description
RIBLBD[7:0]
7-0
(00)001001 Defines the user-programmable receive Inband loopback deactivate code. The default selection is 001001.
RIBLBD [7:0] form the 8-bit repeating code
RIBLBD [6:0] form the 7-bit repeating code
RIBLBD [5:0] form the 6-bit repeating code
RIBLBD [4:0] form the 5-bit repeating code
Programming Information
45
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-39 MAINT6: Maintenance Function Control Register 6
(R/W, Address = 13H)
Symbol
-
Bit
7
Default
Description
0
0
Reserved.
BPV_INS
6
BPV error insertion
A ‘0’ to ‘1’ transition on this bit will cause a single bipolar violation error to be inserted into the transmit data stream.
This bit must be cleared and set again for a subsequent error to be inserted.
ERR_INS
EXZ_DEF
ERR_SEL
5
5
0
0
PRBS logic error insertion
A ‘0’ to ‘1’ transition on this bit will cause a single PRBS logic error to be inserted into the transmit PRBS data stream.
This bit must be cleared and set again for a subsequent error to be inserted.
EXZ definition select
= 0: ANSI
= 1: FCC
3-2
00
These bits choose which type of error will be counted
= 00: The PRBS logic error is counted by a 16-bit error counter.
= 01: The EXZ error is counted by a 16-bit error counter.
= 10: The Received CV (BPV) error is counted by a 16-bit error counter.
= 11: Both CV (BPV) and EXZ errors are counted by a 16-bit error counter.
CNT_MD
CNT_TRF
1
0
0
0
Counter operation mode select
= 0: Manual Report mode
= 1: Auto Report mode
= 0: Clear this bit for the next ‘0’ to ‘1’ transition on this bit.
= 1: Error counting result is transferred to CNT0 and CNT1 and the error counter is reset.
Programming Information
46
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.5 INTERRUPT CONTROL REGISTERS
Table-40 INTM0: Interrupt Mask Register 0
(R/W, Address = 14H)
Symbol
-
Bit
7
Default
Description
1
1
Reserved
IBLBA_IM
6
In-band Loopback activate code detect interrupt mask
= 0: In-band Loopback activate code detect interrupt enabled
= 1: In-band Loopback activate code detect interrupt masked
IBLBD_IM
PRBS_IM
TCLK_IM
DF_IM
5
4
3
2
1
0
1
1
1
1
1
1
In-band Loopback deactivate code detect interrupt mask
= 0: In-band Loopback deactivate code detect interrupt enabled
= 1: In-band Loopback deactivate code detect interrupt masked
PRBS synchronic signal detect interrupt mask
= 0: PRBS synchronic signal detect interrupt enabled
= 1: PRBS synchronic signal detect interrupt masked
TCLK loss detect interrupt mask
= 0: TCLK loss detect interrupt enabled
= 1: TCLK loss detect interrupt masked
Driver Failure interrupt mask
= 0: Driver Failure interrupt enabled
= 1: Driver Failure interrupt masked
AIS_IM
Alarm Indication Signal interrupt mask
= 0: Alarm Indication Signal interrupt enabled
= 1: Alarm Indication Signal interrupt masked
LOS_IM
Loss Of Signal interrupt mask
= 0: Loss Of Signal interrupt enabled
= 1: Loss Of Signal interrupt masked
Programming Information
47
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-41 INTM1: Interrupt Masked Register 1
(R/W, Address = 15H)
Symbol
Bit
Default
Description
DAC_OV_IM
7
1
DAC arithmetic overflow interrupt mask
= 0: DAC arithmetic overflow interrupt enabled
= 1: DAC arithmetic overflow interrupt masked
JAOV_IM
JAUD_IM
ERR_IM
EXZ_IM
CV_IM
6
5
4
3
2
1
0
1
1
1
1
1
1
1
JA overflow interrupt mask
= 0: JA overflow interrupt enabled
= 1: JA overflow interrupt masked
JA underflow interrupt mask
= 0: JA underflow interrupt enabled
= 1: JA underflow interrupt masked
PRBS/QRSS logic error detect interrupt mask
= 0: PRBS/QRSS logic error detect interrupt enabled
= 1: PRBS/QRSS logic error detect interrupt masked
Receive excess zeros interrupt mask
= 0: Receive excess zeros interrupt enabled
= 1: Receive excess zeros interrupt masked
Receive error interrupt mask
= 0: Receive error interrupt enabled
= 1: Receive error interrupt masked
TIMER_IM
CNT_IM
One-Second Timer expiration interrupt mask
= 0: One-Second Timer expiration interrupt enabled
= 1: One-Second Timer expiration interrupt masked
Counter overflow interrupt mask
= 0: Counter overflow interrupt enabled
= 1: Counter overflow interrupt masked
Programming Information
48
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-42 INTES: Interrupt Trigger Edge Select Register
(R/W, Address = 16H)
Symbol
-
Bit
7
Default
Description
0
0
Reserved
IBLBA_IES
6
This bit determines the Inband Loopback Activate Code interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the IBLBA_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the IBLBA_S bit in STAT0
status register
IBLBD_IES
PRBS_IES
TCLK_IES
DF_IES
5
4
3
2
1
0
0
0
0
0
0
0
This bit determines the Inband Loopback Deactivate Code interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the IBLBD_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the IBLBD_S bit in STAT0
status register
This bit determines the PRBS/QRSS synchronization status interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the PRBS_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the PRBS_S bit in STAT0
status register
This bit determines the TCLK Loss interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the TCLK_LOS bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the TCLK_LOS bit in STAT0
status register
This bit determines the Driver Failure interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the DF_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the DF_S bit in STAT0 status
register
AIS_IES
This bit determines the AIS interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the AIS_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the AIS_S bit in STAT0 status
register
LOS_IES
This bit determines the LOS interrupt event.
= 0: Interrupt is generated as a ‘0’ to ‘1’ transition of the LOS_S bit in STAT0 status register
= 1: Interrupt is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the LOS_S bit in STAT0 status
register
Programming Information
49
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.6 LINE STATUS REGISTERS
Table-43 STAT0: Line Status Register 0 (real time status monitor)
(R, Address = 17H)
Symbol
-
Bit
7
Default
Description
0
0
Reserved
IBLBA_S
6
In-band Loopback activate code receive status indication
= 0: No Inband Loopback activate code is detected
= 1: Activate signal is detected and then received over a period of more than t ms, with a bit error rate less than 10-
2. The bit remains set as long as the bit error rate does not exceed 10-2.
Note1:
If automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms.
If automatic remote loopback switching is enabled (ARLP = 1), t = 5.1 s. The rising edge of this bit activates the
remote loopback operation in local end.
Note2:
If IBLBA_IM=0:
A ‘0’ to ‘1’ transition on this bit causes an activate code detected interrupt if IBLBA _IES bit is ‘0’;
Any changes of this bit causes an activate code detected interrupt if IBLBA _IES bit is set to ‘1’.
IBLBD_S
5
0
In-band Loopback deactivate code receive status indication
= 0: No Inband Loopback deactivate signal is detected
= 1: The Inband Loopback deactivate signal is detected and then received over a period of more than t, with a bit
error rate less than 10-2. The bit remains set as long as the bit error rate does not exceed 10-2.
Note1:
If automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms.
If automatic remote loopback switching is enabled (ARLP = 1), t = 5.1 s. The rising edge of this bit disables the
remote loopback operation.
Note2:
If IBLBD_IM=0:
A ‘0’ to ‘1’ transition on this bit causes a deactivate code detected interrupt if IBLBD _IES bit is ‘0’
Any changes of this bit causes a deactivate code detected interrupt if IBLBD _IES bit is set to ‘1’
PRBS_S
4
0
Synchronous status indication of PRBS/QRSS (real time)
= 0: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS is not detected
= 1: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS is detected
Note:
If PRBS_IM=0:
A ‘0’ to ‘1’ transition on this bit causes a synchronous status detected interrupt if PRBS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if PRBS_IES bit is set to ‘1’.
TCLK_LOS
3
0
TCLK loss indication
= 0: Normal
= 1: TCLK pin has not toggled for more than 70 MCLK cycles.
Note:
If TCLK_IM=0:
A ‘0’ to ‘1’ transition on this bit causes an interrupt if TCLK _IES bit is ‘0’.
Any changes of this bit causes an interrupt if TCLK_IES bit is set to ‘1’.
Programming Information
50
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-43 STAT0: Line Status Register 0 (real time status monitor) (Continued)
(R, Address = 17H)
Symbol
Bit
Default
Description
DF_S
2
0
Line driver status indication
= 0: Normal operation
= 1: Line driver short circuit is detected.
Note:
If DF_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if DF _IES bit is ‘0’.
Any changes of this bit causes an interrupt if DF_IES bit is set to ‘1’.
AIS_S
1
0
0
0
Alarm Indication Signal status detection
= 0: No AIS signal is detected in the receive path
= 1: AIS signal is detected in the receive path
Note:
If AIS_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if AIS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if AIS_IES bit is set to ‘1’.
LOS_S
Loss Of Signal status detection
= 0: Loss of signal on RTIP/RRING is not detected.
= 1: Loss of signal on RTIP/RRING is detected.
Note:
If LOS_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if LOS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if LOS_IES bit is set to ‘1’.
Table-44 STAT1: Line Status Register 1 (real time status monitor)
(R, Address = 18H)
Symbol
-
Bit
7-6
5
Default
Description
00
0
Reserved.
RLP_S
Indicating the status of Remote Loopback
= 0: The remote loopback is inactive.
= 1: The remote loopback is active (closed).
-
4-0
00000
Reserved
Programming Information
51
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.7 INTERRUPT STATUS REGISTERS
Table-45 INTS0: Interrupt Status Register 0
(R, Address = 19H) (this register is reset and relevant interrupt request is cleared after a read)
Symbol
-
Bit
7
Default
Description
0
0
Reserved
IBLBA_IS
6
This bit indicates the occurrence of the Inband Loopback Activate Code interrupt event.
= 0: No Inband Loopback Activate Code interrupt event occurred
= 1: Inband Loopback Activate Code interrupt event occurred
IBLBD_IS
PRBS_IS
TCLK_LOS_IS
DF_IS
5
4
3
2
1
0
0
0
0
0
0
0
This bit indicates the occurrence of the Inband Loopback Deactivate Code interrupt event.
= 0: No Inband Loopback Deactivate Code interrupt event occurred
= 1: Interrupt event of the received Inband Loopback Deactivate Code occurred.
This bit indicates the occurrence of the interrupt event generated by the PRBS/QRSS synchronization status.
= 0: No PRBS/QRSS synchronization status interrupt event occurred
= 1: PRBS/QRSS synchronization status interrupt event occurred
This bit indicates the occurrence of the interrupt event generated by the TCLK loss detection.
= 0: No TCLK loss interrupt event.
= 1: TCLK loss interrupt event occurred.
This bit indicates the occurrence of the interrupt event generated by the Driver Failure.
= 0: No Driver Failure interrupt event occurred
= 1: Driver Failure interrupt event occurred
AIS_IS
This bit indicates the occurrence of the AIS (Alarm Indication Signal) interrupt event.
= 0: No AIS interrupt event occurred
= 1: AIS interrupt event occurred
LOS_IS
This bit indicates the occurrence of the LOS (Loss of signal) interrupt event.
= 0: No LOS interrupt event occurred
= 1: LOS interrupt event occurred
Programming Information
52
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-46 INTS1: Interrupt Status Register 1
(R, Address = 1AH) (this register is reset and the relevant interrupt request is cleared after a read)
Symbol
Bit
Default
Description
DAC_OV_IS
7
0
This bit indicates the occurrence of the pulse amplitude overflow of Arbitrary Waveform Generator interrupt event.
= 0: No pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred
= 1: The pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred
JAOV_IS
JAUD_IS
ERR_IS
6
5
4
3
2
1
0
0
0
0
0
0
0
0
This bit indicates the occurrence of the Jitter Attenuator Overflow interrupt event.
= 0: No JA Overflow interrupt event occurred
= 1: JA Overflow interrupt event occurred
This bit indicates the occurrence of the Jitter Attenuator Underflow interrupt event.
= 0: No JA Underflow interrupt event occurred
= 1: JA Underflow interrupt event occurred
This bit indicates the occurrence of the interrupt event generated by the detected PRBS/QRSS logic error.
= 0: No PRBS/QRSS logic error interrupt event occurred
= 1: PRBS/QRSS logic error interrupt event occurred
EXZ_IS
This bit indicates the occurrence of the Excessive Zeros interrupt event.
= 0: No Excessive Zeros interrupt event occurred
= 1: EXZ interrupt event occurred
CV_IS
This bit indicates the occurrence of the Code Violation interrupt event.
= 0: No Code Violation interrupt event occurred
= 1: Code Violation interrupt event occurred
TMOV_IS
CNT_OV_IS
This bit indicates the occurrence of the One-Second Timer Expiration interrupt event.
= 0: No One-Second Timer Expiration interrupt event occurred
= 1: One-Second Timer Expiration interrupt event occurred
This bit indicates the occurrence of the Counter Overflow interrupt event.
= 0: No Counter Overflow interrupt event occurred
= 1: Counter Overflow interrupt event occurred
Programming Information
53
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
4.3.8 COUNTER REGISTERS
Table-47 CNT0: Error Counter L-byte Register 0
(R, Address = 1BH)
Symbol
Bit
Default
Description
Description
CNT_L[7:0]
7-0
00H
This register contains the lower eight bits of the 16-bit error counter. CNT_L[0] is the LSB.
Table-48 CNT1: Error Counter H-byte Register 1
(R, Address = 1CH)
Symbol
Bit
Default
CNT_H[7:0]
7-0
00H
This register contains the upper eight bits of the 16-bit error counter. CNT_H[7] is the MSB.
Programming Information
54
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
5
HARDWARE CONTROL PIN SUMMARY
Table-49 Hardware Control Pin Summary
Pin No.
TQFP
Symbol
Description
17
16
MODE1
MODE0
MODE[1:0]: Operation mode of control interface select
00= Hardware interface
01= Serial interface
10= Parallel – multiplexed – Motorola Interface
11= Parallel – multiplexed – Intel Interface
23
TERM
TERM: Termination interface select
This pin selects internal or external impedance matching for both receiver and transmitter
0= ternary interface with external impedance matching network. External impedance matching is not supported in T1/J1 transmit
line interface.
1= ternary interface with internal impedance matching network
21
20
RXTXM1
RXTXM0
RXTXM[1:0]: Receive and transmit path operation mode select
00= single rail with HDB3/B8ZS coding
01= single rail with AMI coding
10= dual rail interface with CDR enable
11= slicer mode
33
32
31
30
PULS3
PULS2
PULS1
PULS0
PULS[3:0]: These pins are used to select the following functions:
•
•
•
T1/E1/J1 mode
Transmit pulse template
Internal termination impedance (75Ω/100Ω/110Ω/120Ω)
PULS[3:0]
T1/E1/J1
TCLK
Cable impedance
(internal matching
impedance)
Cable range
Cable loss
0000
0001
E1
2.048 MHz
2.048 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
1.544 MHz
75Ω
120Ω
100Ω
100Ω
100Ω
100Ω
100Ω
110Ω
-
0-24 dB
0-24 dB
E1
-
0010
DSX1
DSX1
DSX1
DSX1
DSX1
J1
0-133 ft
133-266 ft
266-399 ft
399-533 ft
533-655 ft
0-655 ft
0-0.6 dB
0011
0.6-1.2 dB
1.2-1.8 dB
1.8-2.4 dB
2.4-3.0 dB
0-3.0 dB
0100
0101
0110
0111
1000 - 1111
Reserved
28
RPD
RPD: Receiver power down control
0= Normal operation
1= receiver power down
27
26
PATT1
PATT0
PATT[1:0]: Transmit test pattern select
In hardware control mode, these pins select the transmit pattern
00 = normal
01= All Ones
10= PRBS
11= transmitter power down
15
14
JA1
JA0
JA[1:0]: Jitter attenuation position, bandwidth and the depth of FIFO select
00= JA is disabled
01= JA in receiver, broad bandwidth, FIFO=64 bits
10= JA in receiver, narrow bandwidth, FIFO=128 bits
11= JA in transmitter, narrow bandwidth, FIFO=128 bits
Hardware Control Pin Summary
55
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-49 Hardware Control Pin Summary (Continued)
Pin No.
TQFP
Symbol
Description
22
MONT
MONT: Receive monitor n gain select
0= 0 dB
1= up to 26 dB
25
24
LP1
LP0
LP[1:0]: Loopback mode select
00= no loopback
01= analog loopback
10= digital loopback
11= remote loopback
13
11
29
THZ
RCLKE
-
THZ: Transmitter Driver High Impedance Enable
This signal enables or disables transmitter driver. A low level on this pin enables the driver while a high level on this pin places the
driver in high impedance state.
RCLKE: the active edge of RCLK select when hardware control mode is used
0= select the rising edge as active edge of RCLK
1= select the falling edge as active edge of RCLK
In Hardware mode, this pin has to be tied to GND.
Hardware Control Pin Summary
56
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
6
TEST SPECIFICATIONS
Table-50 Absolute Maximum Rating
Symbol
Parameter
Min
-0.5
Max
4.6
Unit
V
VDDA, VDDD
VDDIO
Core Power Supply
I/O Power Supply
-0.5
4.6
V
VDDT
Transmit Power Supply
-0.5
4.6
V
Input Voltage, Any Digital Pin
GND-0.5
GND-0.5
5.5
V
Vin
Input Voltage, Any RTIP and RRING pin1
ESD Voltage, any pin
VDDA+0.5
V
2000 2
500 3
V
V
Transient latch-up current, any pin
Input current, any digital pin 4
100
10
mA
mA
Iin
-10
DC Input current, any analog pin 4
Maximum power dissipation in package
Case Temperature
±100
mA
Pd
1.41
120
W
°C
°C
Tc
Ts
Storage Temperature
-65
+150
CAUTION:
Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
1.Reference to ground
2.Human body model
3.Charge device model
4.Constant input current
Table-51 Recommended Operation Conditions
Symbol
Parameter
Min
3.13
3.13
3.13
-40
Typ
3.3
3.3
3.3
25
Max
3.47
3.47
3.47
85
Unit
V
VDDA, VDDD
VDDIO
VDDT
Core Power Supply
I/O Power Supply
V
Transmitter Power Supply
Ambient operating temperature
E1, 75 Ω load
V
TA
°C
50% ones density data
100% ones density data
-
-
52
64
58
70
mA
mA
mA
mA
E1, 120 Ω Load
T1, 100 Ω Load
J1, 110 Ω Load
50% ones density data
100% ones density data
-
-
58
70
64
76
Total current dissipation1,2,3
50% ones density data
100% ones density data
-
-
59
88
65
95
50% ones density data
100% ones density data
-
-
47
58
53
64
1.Power consumption includes power consumption on device and load. Digital levels are 10% of the supply rails and digital outputs driving a 50 pF capacitive load.
2.Maximum power consumption over the full operating temperature and power supply voltage range.
3.Inshorthaulmode,ifinternalimpedancematchingischosen,E175ΩpowerdissipationvaluesaremeasuredwithtemplatePULS[3:0]=0000;E1120Ωpowerdissipationvaluesaremeasured
with template PULS[3:0] = 0001; T1 power dissipation values are measured with template PULS[3:0] = 0110; J1 power dissipation values are measured with template PULS[3:0] = 0111.
Test Specifications
57
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-52 Power Consumption
Symbol
Max1,2
Parameter
Min
Typ
Unit
E1, 3.3 V, 75 Ω Load
50% ones density data:
100% ones density data:
-
-
172
212
-
mW
243
E1, 3.3 V, 120 Ω Load
50% ones density data:
100% ones density data:
-
-
192
243
-
mW
mW
264
T1, 3.3 V, 100 Ω Load3
J1, 3.3 V, 110 Ω Load
-
-
195
291
-
50% ones density data:
100% ones density data:
330
50% ones density data:
100% ones density data:
-
-
155
192
mW
222
1.Maximum power and current consumption over the full operating temperature and power supply voltage range.
2.Power consumption includes power absorbed by line load and external transmitter components.
3.T1 is measured with maximum cable length.
Table-53 DC Characteristics
Symbol
Parameter
Input Low Level Voltage
Min
Typ
Max
Unit
VIL
VIH
-
-
0.8
V
V
V
V
V
Input High Voltage
2.0
-
-
-
-
VOL
VOH
VMA
Output Low level Voltage (Iout=1.6mA)
Output High level Voltage (Iout=400µA)
0.4
2.4
-
VDDIO
Analog Input Quiescent Voltage (RTIP, RRING
pin while floating)
1.5
IZL
High Impedance Leakage Current
-10
10
µA
Ci
Input capacitance
15
50
pF
pF
pF
Co
Co
Output load capacitance
Output load capacitance (bus pins)
100
Test Specifications
58
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-54 E1 Receiver Electrical Characteristics
Symbol
Parameter
Receiver sensitivity
Min
Typ
Max
Unit
Test conditions
Adaptive Equalizer Disabled:
Adaptive Equalizer Enabled:
-10
-20
dB
Analog LOS level
A LOS level is programmable with Adaptive
Adaptive Equalizer Disabled:
Adaptive Equalizer Enabled:
800
mVp-p Equalizer enabled. Not available in Hardware
dB mode.
-4
-24
0.05
±1%
Allowable consecutive zeros before LOS
G.775:
32
2048
I.431/ETSI300233:
LOS reset
12.5
% ones G.775, ETSI 300 233
Receive Intrinsic Jitter
20 Hz - 100 kHz
U.I.
JA enabled
Input Jitter Tolerance
1 Hz – 20 Hz
37
5
2
U.I.
U.I.
U.I.
G.823, with 6 dB cable attenuation
20 Hz – 2.4 KHz
18 KHz – 100 KHz
ZDM
Receiver Differential Input Impedance
Input termination resistor tolerance
20
KΩ
Internal mode
Receive Return Loss
51 KHz – 102 KHz
RRX
RPD
20
20
20
dB
dB
dB
G.703 Internal termination
102 KHz – 2.048 MHz
2.048 MHz – 3.072 MHz
Receive path delay
Single rail
Dual rail
7
2
U.I.
U.I.
JA disabled
Test Specifications
59
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-55 T1/J1 Receiver Electrical Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
Test conditions
sensitivity
-10
-
dB
Analog LOS level
800
mVp-p
dB
-4
-
Allowable consecutive zeros before LOS
T1.231-1993
I.431
175
1544
LOS reset
12.5
% ones G.775, ETSI 300 233
Receive Intrinsic Jitter
10 Hz - 8 kHz
10 Hz - 40 kHz
8 kHz - 40 kHz
Wide band
JA enabled
0.02
0.025
0.025
0.050
U.I.
U.I.
U.I.
U.I.
Input Jitter Tolerance
0.1 Hz – 1 Hz
138.0
28.0
0.4
U.I.
U.I.
U.I.
AT&T62411
4.9 Hz – 300 Hz
10 KHz – 100 KHz
ZDM
Receiver Differential Input Impedance
Input termination resistor tolerance
20
KΩ
Internal mode
±1%
RRX
Receive Return Loss
39 KHz – 77 KHz
20
20
20
dB
dB
dB
G.703
Internal termination
77 KHz - 1.544 MHz
1.544 MHz – 2.316 MHz
RPD
Receive path delay
Single rail
JA disabled
7
2
U.I.
U.I.
Dual rail
Test Specifications
60
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-56 E1 Transmitter Electrical Characteristics
Symbol
Vo-p
Parameter
Min
Typ
Max
Unit
Output pulse amplitudes
E1, 75 Ω load
2.14
2.7
2.37
3.0
2.60
3.3
V
V
E1, 120 Ω load
Vo-s
Zero (space) level
E1, 75 Ω load
-0.237
-0.3
0.237
0.3
V
V
E1, 120 Ω load
Transmit amplitude variation with supply
-1
+1
%
mV
ns
Difference between pulse sequences for 17 consecutive pulses (T1.102)
Output Pulse Width at 50% of nominal amplitude
200
256
1.05
Tpw
RTX
232
244
Ratio of the amplitudes of Positive and Negative Pulses at the center of the pulse interval
(G.703)
0.95
Ratio of the width of Positive and Negative Pulses at the center of the pulse interval (G.703)
Transmit Return Loss (G.703)
0.95
1.05
51 KHz – 102 KHz
102 KHz - 2.048 MHz
2.048 MHz – 3.072 MHz
20
15
12
dB
dB
dB
JTXp-p
Td
Intrinsic Transmit Jitter (TCLK is jitter free)
20 Hz – 100 KHz
0.050
U.I.
Transmit path delay (JA is disabled)
Single rail
Dual rail
8.5
4.5
U.I.
U.I.
Isc
Line short circuit current (measured on the TTIP/TRING pins)
100
mAp
Test Specifications
61
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-57 T1/J1 Transmitter Electrical Characteristics
Symbol
Parameter
Min
2.4
Typ
Max
3.6
Unit
V
Vo-p
Vo-s
Output pulse amplitudes
Zero (space) level
3.0
-0.15
-1
0.15
+1
V
Transmit amplitude variation with supply
%
Difference between pulse sequences for 17 consecutive pulses
(T1.102)
200
mV
TPW
Output Pulse Width at 50% of nominal amplitude
Pulse width variation at the half amplitude (T1.102)
338
350
362
20
ns
ns
Imbalance between Positive and Negative Pulses amplitude
(T1.102)
0.95
1.05
Output power level (T1.102)
@772 kHz
@1544 kHz (referenced to power at 772kHz)
12.6
-29
17.9
dBm
dBm
RTX
Transmit Return Loss
39 KHz – 77 KHz
77 KHz – 1.544 MHz
1.544 MHz – 2.316 MHz
20
15
12
dB
dB
dB
JTXP-P
Intrinsic Transmit Jitter (TCLK is jitter free)
10 Hz – 8 KHz
8 KHz – 40 KHz
10 Hz – 40 KHz
wide band
0.020
0.025
0.025
0.050
U.I.p-p
U.I.p-p
U.I.p-p
U.I.p-p
Td
Transmit path delay (JA is disabled)
Single rail
Dual rail
8.5
4.5
U.I.
U.I.
ISC
Line short circuit current (measured on the TTIP/TRING pins)
100
mAp
Test Specifications
62
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-58 Transmitter and Receiver Timing Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
MCLK frequency
E1:
T1/J1:
2.048
1.544
MHz
MCLK tolerance
MCLK duty cycle
-100
30
100
70
ppm
%
Transmit path
TCLK frequency
E1:
T1/J1:
2.048
1.544
MHz
TCLK tolerance
-50
10
40
40
+50
90
ppm
%
TCLK Duty Cycle
t1
t2
Transmit Data Setup Time
Transmit Data Hold Time
ns
ns
Delay time of THZ low to driver high impedance
Delay time of TCLK low to driver high impedance
10
us
75
U.I.
Receive path
Clock recovery capture range 1
E1
± 80
± 180
50
ppm
%
T1/J1
RCLK duty cycle 2
40
60
RCLK pulse width 2
t4
E1:
T1/J1:
457
607
488
648
519
689
ns
ns
t5
t6
RCLK pulse width low time
E1:
T1/J1:
203
259
244
324
285
389
RCLK pulse width high time
E1:
T1/J1:
203
259
244
324
285
389
ns
ns
Rise/fall time 3
20
t7
t8
Receive Data Setup Time
E1:
T1/J1:
200
200
244
324
ns
ns
Receive Data Hold Time
E1:
T1/J1:
200
200
244
324
1.Relative to nominal frequency, MCLK= ± 100 ppm
2.RCLK duty cycle widths will vary depending on extent of received pulse jitter displacement. Maximum and minimum RCLK duty cycles are for worst case jitter conditions (0.2 UI displacement
for E1 per ITU G.823).
3.For all digital outputs. C load = 15 pF
Test Specifications
63
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
TCLK
t1
t2
TD/TDP
TDN
Figure-20 Transmit System Interface Timing
t4
RCLK
t6
t7
t5
t8
RDP/RD
(RCLK_SEL = 0 software mode)
(RCLKE = 0 hardware mode)
RDN/CV
t7
t8
RDP/RD
(RCLK_SEL = 1 software mode)
(RCLKE = 1 hardware mode)
RDN/CV
Figure-21 Receive System Interface Timing
Table-59 Jitter Tolerance
Jitter Tolerance
Min
Typ
Max
Unit
Standard
E1: 1 Hz
20 Hz – 2.4 KHz
18 KHz – 100 KHz
T1/J1: 1 Hz
37
1.5
0.2
U.I.
U.I.
U.I.
G.823
Cable attenuation is 6 dB
AT&T 62411
138.0
28.0
0.4
U.I.
U.I.
U.I.
4.9 Hz – 300 Hz
10 KHz – 100 KHz
Test Specifications
64
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Figure-22 E1 Jitter Tolerance Performance
Test Specifications
65
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Figure-23 T1/J1 Jitter Tolerance Performance
Test Specifications
66
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-60 Jitter Attenuator Characteristics
Parameter
Min
Typ
Max
Unit
Jitter Transfer Function Corner (-3 dB) Frequency
E1, 32/64/128 bits FIFO
JABW = 0:
6.8
0.9
Hz
Hz
JABW = 1:
T1/J1, 32/64/128 bits FIFO
JABW = 0:
5
1.25
Hz
Hz
JABW = 1:
Jitter Attenuator
E1: (G.736)
@ 3 Hz
@ 40 Hz
-0.5
-0.5
+19.5
+19.5
dB
@ 400 Hz
@ 100 kHz
T1/J1: (Per AT&T pub.62411)
@ 1 Hz
0
0
@ 20 Hz
@ 1 kHz
@ 1.4 kHz
@ 70 kHz
+33.3
40
40
Jitter Attenuator Latency Delay
32 bits FIFO:
64 bits FIFO:
128 bits FIFO:
16
32
64
U.I.
U.I.
U.I.
Input jitter tolerance before FIFO overflow or underflow
32 bits FIFO:
64 bits FIFO:
128 bits FIFO:
28
58
120
U.I.
U.I.
U.I.
Test Specifications
67
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Figure-24 E1 Jitter Transfer Performance
Test Specifications
68
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Figure-25 T1/J1 Jitter Transfer Performance
Test Specifications
69
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
7
MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS
7.1 SERIAL INTERFACE TIMING
Table-61 Serial Interface Timing Characteristics
Symbol
t1
Parameter
Min
100
100
5
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
Comments
SCLK High Time
t2
SCLK Low Time
t3
Active CS to SCLK Setup Time
t4
Last SCLK Hold Time to Inactive CS Time
CS Idle Time
41
41
0
t5
t6
SDI to SCLK Setup Time
t7
SCLK to SDI Hold Time
82
t10
t11
SCLK to SDO Valid Delay Time
Inactive CS to SDO High Impedance Hold Time
95
90
CS
t4
t5
t3
t6
t1
LSB
3
t2
SCLK
SDI
t7
t7
LSB
Figure-26 Serial Interface Write Timing
MSB
13
1
2
4
5
6
7
8
9
10
11
12
3
14
15
16
SCLK
CS
t4
t10
t11
SDO
0
1
2
4
5
6
7
Figure-27 Serial Interface Read Timing with SCLKE=1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SCLK
CS
t4
t10
t11
7
SDO
0
1
2
3
4
5
6
Figure-28 Serial Interface Read Timing with SCLKE=0
Microcontroller Interface Timing Characteristics
70
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
7.2 PARALLEL INTERFACE TIMING
Table-62 Multiplexed Motorola Read Timing Characteristics
Symbol
tRC
Parameter
Min
190
180
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Read Cycle Time
tDW
Valid DS Width
tRWV
tRWH
tASW
tADD
tADS
Delay from DS to Valid Read
R/W to DS Hold Time
15
65
10
0
Valid AS Width
Delay from AS active to DS active
Address to AS Setup Time
5
tADH
tPRD
Address to AS Hold Time
5
DS to Valid Read Data Propagation Delay
Delay from DS inactive to data bus High Impedance
Acknowledgement Delay
175
20
190
15
5
tDAZ
5
5
5
tAKD
tAKH
tAKZ
Acknowledgement Hold Time
Acknowledgement Release Time
Recovery Time from Read Cycle
tRecovery
tRecovery
tRC
tDW
DS+CS
tRWH
tRWV
R/W
tADD
tASW
AS
tDAZ
tPRD
Valid address
tADS
Valid Data
READ AD[7:0]
tADH
tAKH
tAKZ
tAKD
ACK
Figure-29 Multiplexed Motorola Read Timing
Microcontroller Interface Timing Characteristics
71
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-63 Multiplexed Motorola Write Timing Characteristics
Symbol
tWC
Parameter
Min
120
100
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Write Cycle Time
tDW
Valid DS Width
tRWV
tRWH
tASW
tADD
tADS
Delay from DS to Valid Write
R/W to DS Hold Time
15
65
10
0
Valid AS Width
Delay from AS active to DS active
Address to AS Setup Time
Address to AS Hold Time
Delay from DS to Valid Write Data
Write Data to DS Hold Time
Acknowledgement Delay
Acknowledgement Hold Time
Acknowledgement Release Time
Recovery Time from Write Cycle
5
tADH
tDV
5
15
tDHW
tAKD
tAKH
tAKZ
65
5
150
15
5
tRecovery
5
tRecovery
tWC
tDW
tRWH
DS+CS
tRWV
R/W
AS
tADD
tASW
tDHW
tDV
Valid address
tADS
Valid Data
Write AD[7:0]
tADH
tAKH
tAKZ
tAKD
ACK
Figure-30 Multiplexed Motorola Write Timing
Microcontroller Interface Timing Characteristics
72
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-64 Multiplexed Intel Read Timing Characteristics
Symbol
tRC
Parameter
Min
190
180
0
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Read Cycle Time
tRDW
tARD
Valid RD Width
Delay from ALE to Valid Read
Valid ALE Width
tALEW
tADS
10
5
Address to ALE Setup Time
tADH
Address to ALE Hold Time
5
tPRD
RD to Valid Read Data Propagation Delay
Delay from RD inactive to data bus High Impedance
Acknowledgement Delay
175
20
190
15
5
tDAZ
5
5
5
tAKD
tAKH
Acknowledgement Hold Time
Acknowledgement Release Time
Recovery Time from Read Cycle
tAKZ
tRecovery
tRecovery
tRC
tRDW
RD+CS
tARD
tALEW
ALE
tDAZ
tPRD
Valid address
tADS
Valid Data
READ AD[7:0]
tADH
tAKH
tAKZ
tAKD
RDY
Figure-31 Multiplexed Intel Read Timing
Microcontroller Interface Timing Characteristics
73
December 9, 2005
IDT82V2041E
SINGLE CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Table-65 Multiplexed Intel Write Timing Characteristics
Symbol
tWC
Parameter
Min
120
100
10
0
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Write Cycle Time
Valid WR Width
Valid ALE Width
tWRW
tALEW
tAWD
tADS
Delay from ALE to Valid Write
Address to ALE Setup Time
Address to ALE Hold Time
5
tADH
5
tDV
Delay from WR to Valid Write Data
Write Data to WR Hold Time
Acknowledgement Delay
15
tDHW
tAKD
65
5
150
15
5
tAKH
Acknowledgement Hold Time
Acknowledgement Release Time
Recovery Time from Write Cycle
tAKZ
tRecovery
5
tRecovery
tWC
tWRW
WR+CS
tAWD
tALEW
ALE
tDHW
tDV
Valid address
tADS
Valid Data
Write AD[7:0]
tADH
tAKH
tAKZ
tAKD
RDY
Figure-32 Multiplexed Intel Write Timing
Microcontroller Interface Timing Characteristics
74
December 9, 2005
IDT82V2041E
SINGLE CHANNELT1/E1/J1SHORTHAULLINE INTERFACE UNIT
ORDERING INFORMATION
XXXXXXX
Device Type
XX
X
IDT
Process/
Temperature
Range
Industrial (-40 °C to +85 °C)
Blank
Thin Quad Flatpack (TQFP, PP44)
PP
PPG
Green Thin Quad Flatpack
(TQFP, PPG44)
Short Haul LIU
82V2041E
DATASHEET DOCUMENT HISTORY
12/09/2005 pgs. 1, 14, 21, 22, 28, 36, 37, 44, 62, 63, 75
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
1-800-345-7015 or 408-284-8200
fax: 408-284-2775
for Tech Support:
408-360-1552
email:TELECOMhelp@idt.com
www.idt.com
75
相关型号:
©2020 ICPDF网 联系我们和版权申明