M680-02-AD-AK [IDT]
SAW Oscillator, 690.5692MHz Nom;型号: | M680-02-AD-AK |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | SAW Oscillator, 690.5692MHz Nom |
文件: | 总4页 (文件大小:200K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
P r e l i m i n a r y I n f o r m a t i o n
Integrated
Circuit
Systems, Inc.
M680-02
DUAL SAW, SELECTABLE FREQUENCY VCSO
GENERAL DESCRIPTION
PIN ASSIGNMENT (5 x 7mm SMT)
The M680-02 is a dual SAW, selectable frequency
VCSO frequency source for low-jitter clock
generation. An integrated SAW (surface
acoustic wave) delay line implements the
high-Q VCO (voltage controlled oscillator)
function, which results in low output phase
M680-02
M680
noise and very low jitter. The M680-02 is available in
a range of center frequencies from 500 to 700MHz.
Minimum pull-range is ±50 ppm (wider pull-range is
available). The M680-02 is well suited for phase-locked
loop implementations, clock and data recovery circuits,
and other timing applications in telecom and optical
fiber networking systems (e.g., OC-48, OC-192).
(T op View)
Figure 1: Pin Assignment
FEATURES
Sample of Available Output Frequencies
◆ Two integrated SAW devices
VCSO Center Frequency1 (MHz)
Applications
◆ Selectable output frequency
622.0800
625.0000
644.5313
669.3265
SONET/SDH
Gigabit Ethernet
◆ Supports multi-rate optical interface requirements
◆ VCSO center frequencies from 500 to 700 MHz
(Specify center frequency at time of order)
Gigabit Ethernet FEC
SONET/SDH FEC
◆ Low phase jitter 0.37ps rms typical (12kHz to 20MHz)
◆ Low phase noise -70dBc/Hz @ 1kHz offset typical
◆ Differential 3.3V LVPECL output
Table 1: Sample of Available Output Frequencies
Note 1: Specify VCSO center frequency at time of order.
◆ Single 3.3V power supply
◆ Small 5 x 7mm SMT (surface mount) package
BLOCK DIAGRAM
M680-02
SAW Delay Line
Phase
Shifter
VCSO
FOUT
VIN
nFOUT
SAW Delay Line
Phase
Shifter
VCSO
F_SEL
Figure 2: Block Diagram
M680-02 Datasheet Rev 1.0
Revised 19Sep2003
M680-02 Dual SAW, Selectable Frequency VCSO
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M680-02
Integrated
Circuit
Systems, Inc.
D
UAL SAW, SELECTABLE
FREQUENCY VCSO
P r e l i m i n a r y I n f o r m a t i o n
PIN DESCRIPTIONS
I/O
Input
Number
Name
VIN
Configuration
Description
Tuning control voltage.
1
Frequency select:
Logic 1 selects Frequency 2.
Logic 0 selects Frequency 1.
1
2
F_SEL
GND
Input
Internal pull-down resistor
3
Ground
Power supply ground connections.
4
5
FOUT
nFOUT
Output
Power
No internal terminator
Clock output pair. Differential LVPECL.
6
VCC
Power supply connection, connect to +3.3V.
Table 2: Pin Descriptions
Note 1: See “Frequency Select” in Table 5, DC Characteristics on pg. 3.
1
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter
Rating
Unit
VI
Inputs
-0.5 to VCC +0.5
V
VO
VCC
TS
Outputs
-0.5 to VCC +0.5
3.63
V
Power Supply Voltage
Storage Temperature
V
-55 to +125
oC
Table 3: Absolute Maximum Ratings
Note 1:Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the
device. These ratings are stress specifications only. Functional operation of product at these conditions
or any conditions beyond those listed in Recommended Conditions of Operation, DC Characteristics, or
AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect product reliability
.
RECOMMENDED CONDITIONS OF OPERATION
Symbol Parameter
Min
Typ
Max
Unit
2.97
3.3
3.63
VCC
Positive Supply Voltage
V
oC
-40
TA
Ambient Operating Temperature
25
+85
Table 4: Recommended Conditions of Operation
M680-02 Datasheet Rev 1.0
2 of 4
Revised 19Sep2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M680-02
Integrated
Circuit
Systems, Inc.
D
UAL SAW, SELECTABLE
FREQUENCY VCSO
P r e l i m i n a r y I n f o r m a t i o n
ELECTRICAL SPECIFICATIONS
DC Characteristics
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq.’s = 622.08, 669.3265MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Power Supply VCC Positive Supply Voltage
Pin
Min
2.97
Typ
3.3
Max
3.63
Unit
V
VCC
VIN
90
125
ICC
VIN
Power Supply Current
Input Control Voltage Range
VIN Input Impedence
VIN Modulation Bandwidth
Input High Voltage
mA
V
0
V
Control
Voltage
cc
100
600
kΩ
kHz
V
2
Frequency
1
VIH
VIL
V + 0.3
cc
Select
0.8
Input Low Voltage
-0.3
V
IIH
IIL
R
Input High Current
5
µA
µA
kΩ
F_SEL
Input Low Current
-150
51
Internal Pull-down Resistor
pulldown
Differential
Outputs
VOH
VOL
Output High Voltage
Output Low Voltage
Peak to Peak Output Voltage
Output Current
V
V
- 0.98
V
- 0.75
- 1.63
V
cc
cc
- 1.95
V
V
cc
cc
FOUT, nFOUT
0.450
0.625
0.85
20
VP-P
IOUT
VP-P
mA
Table 5: DC Characteristics
Note 1: Internally pulled down to Logic 0 (Frequency 1) if left unselected.
AC Characteristics
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Freq.’s = 622.08, 669.3265MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Min
500
Typ
Max
700
Unit
MHz
Notes
Frequency
FOUT
Output Center Frequency Range
1
±50
APR
fSTAB
Absolute Pull-Range
Frequency Stability
ppm
75
6
ppm p-p
VIN
Best fit straight line
VIN 0.3 to 3.0
= 0.3 to 3.0V
LIN
Tuning Linearity
%
=
V
KVCO
Average VCO Gain
@622.08MHz
225
-77
ppm/V
-50
Outputs
Non-harmonic Spurious
dBc
100Hz Offset
1kHz Offset
-40
-70
Φn
SSB (single sideband)
Phase Noise, offset
from carrier
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps rms
ps rms
%
10kHz Offset
-99
100kHz Offset
1MHz Offset
-122
-142
0.37
0.19
12kHz to 20MHz
50kHz to 80MHz
J(t)
Jitter (rms)
2
45
55
odc
tR
Output Duty Cycle
2
275
275
400
400
Output Rise Time for FOUT, nFOUT
ps
ps
20% to 80%
20% to 80%
2
tF
Output Fall Time for FOUT, nFOUT
Table 6: AC Characteristics
Note 1: Consult ICS for availability of other APRs.
Note 2: See Parameter Measurement Information on pg. 4.
M680-02 Datasheet Rev 1.0
3 of 4
Revised 19Sep2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M680-02
Integrated
Circuit
Systems, Inc.
D
UAL SAW, SELECTABLE
FREQUENCY VCSO
P r e l i m i n a r y I n f o r m a t i o n
PARAMETER MEASUREMENT INFORMATION
Output Rise and Fall Time
Output Duty Cycle
nFOUT
80%
80%
V
SWING
20%
t
F
20%
Clock
Outputs
FOUT
t
R
t
PW
(Output Pulse Width)
t
PERIOD
t
PW
Figure 3: Output Rise and Fall Time
odc =
t
PERIOD
Figure 4: Output Duty Cycle
DEVICE PACKAGE - 5 x 7mm SMT (Surface Mount) Package
Mechanical Dimensions:
Dimensions are in mm;
dimensions in [ ] are in inches
Unless otherwise specified, all
dimensions are ±0.13 [0.005]
Figure 5: Device Package - 5 x 7mm SMT (Surface Mount) Package
Standard Output Frequencies
ORDERING INFORMATION
AA
AB
AC
AD
AE
AF
622.0800
625.0000
627.3296
644.5313
666.5143
669.1281
AG
AH
A I
AJ
AK
AL
669.3120
669.3265
670.8386
672.1600
690.5692
693.4830
For Output Frequencies (MHz)
Order Part Number
Frequency 1, Frequency 2
M680-02-Ax-Ax
e.g., 622.0800, 669.3265
M680-02-AA-AH
Table 7: Ordering Information
Table 8: Standard Output Frequencies
Consult ICS for the availability of other VCSO frequencies.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
M680-02 Datasheet Rev 1.0
4 of 4
Revised 19Sep2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
相关型号:
©2020 ICPDF网 联系我们和版权申明