MK1604-01S [IDT]
Clock Generator, 40.5MHz, CMOS, PDSO16, 0.150 INCH, SOIC-16;![MK1604-01S](http://pdffile.icpdf.com/pdf2/p00267/img/icpdf/MK1604-01S_1607947_icpdf.jpg)
型号: | MK1604-01S |
厂家: | ![]() |
描述: | Clock Generator, 40.5MHz, CMOS, PDSO16, 0.150 INCH, SOIC-16 时钟 光电二极管 外围集成电路 晶体 |
文件: | 总4页 (文件大小:44K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
MK1604
Low Cost Video CD Clock Source
ICRO CLOC K
Description
Features
The MK1604 provides clocks for video CD
systems. It is designed to work with many popular
MPEG 1 decoder solutions and microcontrollers.
The chip uses MicroClock’s proprietary analog
Phase-Locked Loop technology, and generates all
of the outputs from a 16.9344MHz input crystal.
This chip eliminates multiple crystals and
• Packaged in 16 pin narrow (150 mil) SOIC
• Compatible with all popular MPEG I decoders
• Nine different microcontroller frequencies
selectable from 4 MHz to 32 MHz
oscillators in video CD systems, saving component
cost, component count, board stuffing cost, and
increasing reliability by removing mechanical
quartz devices from the system.
• Fixed clocks of 13.5, 27, and 40.5 MHz
• Power Down pin turns off some outputs
• All clocks are frequency-locked to each other
• Two outputs of 16.9344. Each can drive 2-3 loads
• 2.7V to 5.5V operation
MicroClock can customize this device for any
different frequencies for a small NRE.
Block Diagram
VDD
GND
2
2
Power Down
CCS1,0
Output
40.5 MHz
Buffer
2
Output
Buffer
Clock Synthesis
and Control
Circuitry
27 MHz
Output
Buffer
13.5 MHz
Output
Buffer
Controller Clock
16.9344 MHz
crystal
or
clock
X1
Output
Buffer
Clock
Buffer/
Crystal
16.9344 MHz
16.9344 MHz
Output
Buffer
Oscillator
X2
MDS1604C
1
Revision 12037
Printed 12/3/97
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MK1604
Low Cost Video CD Clock Source
ICRO CLOC K
Pin Assignment
Controller Clock
Decoding Table
CCS1 CCS0
pin 10 pin 11
CCLK
pin 9
X1/ICLK
VDD
1
2
3
16
15
X2
NC
0
0
0
M
1
Test
23 MHz
11.5 MHz
16 MHz
4 MHz
8 MHz
32.5 MHz
20 MHz
10 MHz
VDD
PD
14 16.9344M
0
M
M
M
1
0
4
5
6
16.9344M
13
12
11
10
9
M
1
GND
GND
13.5M
27M
40.5M
CCS0
CCS1
CCLK
0
1
M
1
7
8
1
M = mid level. The inputs are self-biased to this level
when the pins are left unconnected. 0 or 1 means to
connect directly to ground or VDD, respectively.
16 pin narrow (150 mil) SOIC
Pin Descriptions
Number
Name
X1/ICLK
VDD
Type Description
1
2
I
P
P
I
Crystal connection. Connect to 16.9344 MHz crystal, or clock input
Connect to +3.3V or +5V. Must be same as other VDDs.
3
VDD
Connect to +3.3V or +5V. Must be same as other VDDs.
Power Down. Stops 40.5, 27 and 13.5 MHz clocks low when taken low.
Connect to ground.
4
PD
5
GND
P
P
O
O
O
I
6
GND
Connect to ground.
7
13.5M
27M
13.5 MHz clock output.
8
27.00 MHz clock output.
9
CCLK
CCS1
CCS0
40.5M
16.9344M
16.9344M
NC
Controller Clock output. Determined by CCS0, CCS1 per Table above.
Controller Clock Select 1. Determines CCLK output per Table above.
Controller Clock Select 0. Determines CCLK output per Table above.
40.5 MHz clock output.
10
11
12
13
14
15
16
I
O
O
O
-
16.9344 MHz buffered crystal oscillator output.
16.9344 MHz buffered crystal oscillator output.
No Connect.
X2
O
Crystal connection. Leave unconnected for clock input, or connect to 16.9344 MHz crystal.
Type: I = Input, O = output, P = power supply connection
MDS1604C
2
Revision 12037
Printed 12/3/97
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MK1604
Low Cost Video CD Clock Source
ICRO CLOC K
External Components/Crystal Selection
The MK1604 requires a minimum number of external components for proper operation. For a crystal input,
a parallel resonant 16.9344 MHz, 18pF load, crystal is recommended. The frequency tolerance of the
crystal should be 50ppm or better. For a clock input, connect to X1 and leave X2 unconnected. VDD and
GND pins should be connected together, a decoupling capacitor of 0.1µF must be connected between
them very close to the chip, and 33Wterminating resistors should be used on clock outputs with traces
longer than 1 inch.
Electrical Specifications
Parameter
Conditions
Minimum
Typical
Maximum
Units
ABSOLUTE MAXIMUM RATINGS (Note 1)
Supply Voltage, VDD
Referenced to GND
7
VDD+0.5
70
V
V
Inputs and Clock Outputs
Ambient Operating Temperature
Soldering Temperature
-0.5
0
°C
°C
°C
Max of 10 seconds
250
Storage Temperature
-65
150
DC CHARACTERISTICS
Operating Voltage, VDD
Input High Voltage, VIH
Input Low Voltage, VIL
Output High Voltage
2.7
2
5.5
0.8
V
V
V
IOH=-4mA
VDD-0.4
2.4
V
Output High Voltage
IOH=-25mA
V
Output Low Voltage
IOL=25mA
0.4
V
Operating Supply Current, IDD
Operating Supply Current, IDD
Standby Supply Current, IDD, at 3.0V
Short Circuit Current
No Load, VDD=5.0V
No Load, VDD=3.0V
No Load, PD=0V
Each output
TBD
TBD
TBD
±100
15
mA
mA
mA
mA
pF
pF
ppm
%
Input Capacitance, X1 and X2 pins
Input Capacitance
7
Actual mean frequency error versus target, note 2 13.5, 27, and 40.5MHz
7
2
Controller clocks
Actual mean frequency error versus target
AC CHARACTERISTICS
Input Frequency
16.9344
49 to 51
MH z
ns
Output Clock Rise Time
0.8 to 2.0V
2.0 to 0.8V
At VDD/2
At VDD/2
1.5
1.5
55
60
1
Output Clock Fall Time
ns
Output Clock Duty Cycle, High Time
Output Clock Duty Cycle, High Time, note 3
Power down Time, PD taken low to clocks off
Power up Time, PD taken high to clocks stable
Note:
45
40
%
%
µs
1
ms
1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure
to levels above the operating limits but below the Absolute Maximums may affect device reliability.
2. Provided the crystal is properly tuned, or an accurate 16.9344 MHz input clock is used.
3. This spec applies only to the 32 and 23MHz controller clock selections.
MDS1604C
3
Revision 12037
Printed 12/3/97
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MK1604
Low Cost Video CD Clock Source
ICRO CLOC K
Package Outline and Package Dimensions
16 pin SOIC narrow
Inches
Symbol Min
Millimeters
Min Max
Max
A
b
0.055 0.070 1.397
0.013 0.019 0.330
0.007 0.010 0.190
1.778
0.483
0.254
E
H
c
D
E
H
e
0.385 0.400 9.779 10.160
0.150 0.160 3.810
0.225 0.245 5.715
4.064
6.223
.050 BSC
0.016
0.01
1.27 BSC
h
0.406
0.254
h x 45°
Q
0.004
0.102
D
A
c
Q
b
e
Ordering Information
Part/Order Number
Marking
Package
Temperature
MK1604-01S
MK1604-01S
MK1604-01S
16 pin narrow SOIC
Add Tape & Reel
0-70°C
0-70°C
MK1604-01STR
While the information presented herein has been checked for both accuracy and reliability, MicroClock Incorporated assumes no responsibility for either its use or for the
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in
normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by MicroClock. MicroClock reserves the right to change any circuitry or specifications without notice. MicroClock does not
authorize or warrant any MicroClock product for use in life support devices or critical medical instruments.
CHANGE HISTORY
Version Date first published
12/15/95
Comments
Original
A
MDS1604C
4
Revision 12037
Printed 12/3/97
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00297/img/page/MJ1302FEA26_1797957_files/MJ1302FEA26_1797957_1.jpg)
MK1622FEA52
RESISTOR, METAL FILM, 0.25W, 1%, 50ppm, 16200ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
OHMITE
![](http://pdffile.icpdf.com/pdf2/p00297/img/page/MJ1302FEA26_1797957_files/MJ1302FEA26_1797957_1.jpg)
MK1622FER58
RESISTOR, METAL FILM, 0.25 W, 1 %, 50 ppm, 16200 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
OHMITE
©2020 ICPDF网 联系我们和版权申明