MK1726-04AS [IDT]
Clock Generator, 128MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8;型号: | MK1726-04AS |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Clock Generator, 128MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8 光电二极管 |
文件: | 总8页 (文件大小:162K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MK1726A
Low EMI Clock Generator
Description
Features
The MK1726-01A/-02A/-04A devices generate a low
EMI output clock from a clock or crystal input. The part
is designed to dither the LCD interface clock for PDAs,
printers, scanners, modems, copiers, etc. Using ICS’
proprietary mix of analog and digital Phase Locked
Loop (PLL) technology, the device spreads the
frequency spectrum of the output and reduces the
frequency amplitude peaks by several dB. The
MK1726-01A/-02A/-04A devices offer both centered
and down spread from a high-speed clock input.
• Packaged in 8-pin SOIC/TSSOP
• Provides a spread spectrum output clock
• Supports flat panel controllers
• Accepts a clock or crystal input (provides same
frequency dithered output)
• Input frequency range of 4 to 32 MHz.
• Output frequency range of 4 to 128 MHz
• 1X, 2X, 4X frequency multiplication
• 1X: MK1726-01A; 2X: MK1726-02A; 4X:
ICS offers many other clocks for computers and
computer peripherals. Consult ICS when you need to
remove crystals and oscillators from your board.
MK1726-04A
• Center and down spread
• Peak reduction by 8 dB to 16 dB typical on 3rd
through 19th odd harmonics
• Low EMI feature can be disabled
• Includes power down
• Operating voltage of 3.3 V
• Advanced, low-power CMOS process
Block Diagram
VDD
2
S1:0
PLL Clock
Synthesis
and Spread
Spectrum
Circuitry
Spread Direction
FRSEL
SSCLK
X1= 01A
X2= 02A
X4= 04A
X1/CLK
Clock Buffer/
Crystal
Ocsillator
X2
GND
The crystal requires external capacitors
for accurate tuning of the clock
MDS 1726A B
1
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
Pin Assignment
Spread Direction and Spread
Percentage
S1
S0
Spread
Spread
X1/ICLK
1
8
7
Pin 3 Pin 4
Direction
Percentage
X2
0
0
0
M
1
0
M
1
0
M
1
Center
Center
Center
Center
No Spread
Down
Down
Down
Down
±1.4
±1.1
±0.6
±0.5
-
-1.6
-2.0
-0.7
-3.0
GND
S1
2
3
4
VDD
6
5
FRSEL
SSCLK
0
S0
M
M
M
1
8-pin (150 mil) SOIC/TSSOP
1
1
0 = connect to GND
M = unconnected (floating)
1 = connect directly to VDD
Frequency Selection
Product
FRSEL
(pin 6)
Input
Multiplier
Output
Freq. Range
Freq. Range
MK1726-01A
MK1726-01A
MK1726-01A
MK1726-02A
MK1726-02A
MK1726-02A
MK1726-04A
MK1726-04A
MK1726-04A
0
1
4.0 to 8.0 MHz
8.0 to 16.0MHz
16.0 to 32.0MHz
4.0 to 8.0 MHz
8.0 to 16.0MHz
16.0 to 32.0MHz
4.0 to 8.0 MHz
8.0 to 16.0MHz
16.0 to 32.0MHz
X1
X1
X1
X2
X2
X2
X4
X4
X4
4.0 to 8.0 MHz
8.0 to 16.0MHz
16.0 to 32.0MHz
8.0 to 16.0MHz
16.0 to 32.0MHz
32.0 to 64.0MHz
16.0 to 32.0MHz
32.0 to 64.0MHz
64.0 to 128MHz
M
0
1
M
0
1
M
0 = connect to GND
M = unconnected (floating)
1 = connect directly to VDD
MDS 1726A B
2
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
Pin Descriptions
Pin
Number
Pin
Name
Pin Type
Pin Description
Connect to 4-32 MHz crystal or clock.
1
2
3
X1/ICLK
GND
S1
Input
Power Connect to ground.
Input
Function select 1 input. Selects spread amount and direction per table above.
(default-internal mid-level).
4
S0
Input
Function select 0 input. Selects spread amount and direction per table above.
(default-internal mid-level).
5
6
7
8
SSCLK
FRSEL
VDD
Output Clock output with Spread spectrum
Input Function select for input frequency range. Default to mid level “M”.
Power Connect to +3.3 V.
XO Crystal connection to 4-32 MHz crystal. Leave unconnected for clock
X2
PCB Layout Recommendations
External Components
For optimum device performance and lowest output
phase noise, observe the following guidelines:
The MK1726-01A/-02A/-04A devices require a
minimum number of external components for proper
operation.
1) Mount the 0.01µF decoupling capacitor on the
component side of the board as close to the VDD pin
as possible. No vias should be used between the
decoupling capacitor and VDD pin. The PCB trace to
the VDD pin and the PCB trace to the ground via
should be kept as short as possible.
Decoupling Capacitor
A decoupling capacitor of 0.01µF must be connected
between VDD and GND on pins 7 and 2. Connect the
capacitor as close to these pins as possible. For
optimum device performance, mount the decoupling
capacitor on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
2) To minimize EMI, place the 33Ω series-termination
resistor (if needed) close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, thus minimizing vias through
other signal layers. Other signal traces should be
routed away from the MK1726A devices. This includes
signal traces located underneath the device, or on
layers adjacent to the ground plane layer used by the
device.
Series Termination Resistor
Use series termination when the PCB trace between
the clock output and the load is over 1 inch. To series
terminate a 50Ω trace (a commonly used trace
impedance), place a 33Ω resistor in series with the
clock line. Place the resistor as close to the clock
output pin as possible. The nominal impedance of the
clock output is 20Ω.
Crystal Information
The crystal used should be a fundamental mode (do
not use third overtone), parallel resonant crystal. To
optimize the initial accuracy, connect crystal capacitors
from pins X1 to ground and X2 to ground. The value of
these capacitors is given by the following equation:
Tri-level Select Pin Operation
The S1 and S0 select pins are tri-level, meaning that
they have three separate states to make the selections
shown in the table on page 2. To select the M (mid)
level, the connection to these pins must be eliminated
by either floating them originally, or tri-stating the GPIO
pins which drive the select pins.
Crystal caps (pF) = (C - 6) x 2
L
MDS 1726A B
3
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
In the equation, C is the crystal load capacitance. For
L
example, a crystal with a 16 pF load capacitance uses
two 20 pF [(16-6) x 2] capacitors.
Modulation Rate
Spread Spectrum Profile
The MK1726-01A/-02A/-04A device’s low EMI clock
generator uses an optimized frequency slew rate
algorithm to facilitate down stream tracking of zero
delay buffers and other PLL devices.
T i m e
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK1726A devices. These
ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional
operation of the device, at these or any other conditions, above those indicated in the operational sections
of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods
can affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
All Inputs and Outputs
7 V
-0.5 V to VDD+0.5 V
0 to +85°C
-65 to +150°C
175°C
Ambient Operating Temperature
Storage Temperature
Junction Temperature
Soldering Temperature
260°C
Recommended Operation Conditions
Parameter
Min.
Typ.
Max.
+70
Units
°C
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
0
+3.0
3.63
V
MDS 1726A B
4
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +85°C
Parameter
Operating Voltage
Supply Current
Symbol
VDD
Conditions
Min.
Typ.
3.3
Max.
3.63
25
Units
V
3.0
IDD
No load, at 3.3 V, Fin=12 MHz
No load, at 3.3 V, Fin=24 MHz
No load, at 3.3 V, Fin=32 MHz
23
mA
mA
mA
V
30
35
Input High Voltage
Input middle Voltage
Input Low Voltage
Output High Voltage
Output High Voltage
Output Low Voltage
V
0.85VDD
0.4VDD
0.0
VDD
0.5VDD
0.0
VDD
0.6
IH
V
V
IHM
V
0.15
V
IL
V
V
CMOS, I = -4 mA
2.4
V
OH
OH
OH
I
I
I
= -6 mA
= -4 mA
= -10 mA
2.0
V
OH
OL
OL
V
0.4
1.2
6
V
OL
V
Input Capacitance
C
C
S0, S1, FRSEL pins
X1, X2 pins
4
6
pF
pF
IN1
9
IN2
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +85° C, C = 15 pF
L
Parameter
Symbol
Conditions
Min.
4
Typ. Max. Units
Input Clock Frequency
32
128
60
MHz
MHz
%
Output Clock Frequency
Input Clock Duty Cycle
4
Time above VDD/2
40
45
Output Clock Duty Cycle
Cycle-to-cycle Jitter (-01A)
Cycle-to-cycle Jitter (-01A)
Cycle-to-cycle Jitter (-02A)
Cycle-to-cycle Jitter (-02A)
Cycle-to-cycle Jitter (-04A)
Cycle-to-cycle Jitter (-04A)
Output Rise Time (-01A, -02A)
Output Fall Time (-01A, -02A)
Time above 1.5 V
50
350
260
260
260
360
360
3.2
55
%
Fin=4MHz, Fout=4 MHz
Fin=8MHz, Fout=8 MHz
Fin=8MHz, Fout=16 MHz
Fin=16MHz, Fout=32 MHz
Fin=16MHz,Fout=64 MHz
Fin=32MHz, Fout=128 MHz
0.4 to 2.4 V
800
550
550
550
800
800
5.0
4.4
3.6
3.6
6.9
6.9
ps
ps
ps
ps
ps
ps
t
2.0
2.0
1.2
1.2
2.2
2.2
ns
R
t
2.4 to 0.4 V
3.2
ns
F
R
R
t
t
2.2
ns
FSEL = M (-04A only)
2.2
ns
t
t
4.3
ns
F
F
FSEL = 1, 0 (-04A only)
4.3
ns
EMI Peak Frequency Reduction
8 to 16
dB
MDS 1726A B
5
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
Package Outline and Package Dimensions (8-pin TSSOP)
Package dimensions are kept current with JEDEC Publication No. 95
8
Millimeters
Min Max
Inches
Symbol
Min
--
Max
A
A1
A2
b
--
1.20
0.15
1.05
0.30
0.20
3.10
0.047
0.006
0.041
0.012
0.05
0.80
0.19
0.09
3.90
0.002
0.032
0.007
E1
E
INDEX
AREA
C
0.0035 0.008
0.114 0.122
0.252 BASIC
0.169 0.177
0.0256 Basic
D
E
6.40 BASIC
4.30 4.50
0.65 Basic
1
2
E1
e
D
L
0.45
0°
0.75
8°
0.018
0.030
8°
α
0°
aaa
-
0.10
-
0.004
A
2
A
A
1
c
- C -
e
SEATING
PLANE
b
L
aaa
C
Thermal Characteristics for 8-pin TSSOP
Parameter
Symbol
Conditions
Min.
Typ. Max. Units
Thermal Resistance Junction to
Ambient
θ
θ
θ
θ
Still air
110
100
80
°C/W
°C/W
°C/W
°C/W
JA
JA
JA
JC
1 m/s air flow
3 m/s air flow
Thermal Resistance Junction to Case
35
MDS 1726A B
6
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
Inches
8
Symbol
Min
Max
1.75
0.25
0.51
0.25
5.00
4.00
Min
Max
A
A1
B
1.35
0.10
0.33
0.19
4.80
3.80
.0532
.0040
.013
.0688
.0098
.020
E
H
INDEX
AREA
C
D
E
e
.0075
.1890
.1497
.0098
.1968
.1574
1.27 BASIC
0.050 BASIC
1
2
H
h
5.80
0.25
0.40
0°
6.20
.2284
.010
.016
0°
.2440
.020
.050
8°
0.50
1.27
8°
D
L
α
A
h x 45
A1
C
- C -
e
SEATING
PLANE
B
L
.10 (.004)
C
Thermal Characteristics for 8-pin SOIC
Parameter
Symbol
Conditions
Min.
Typ. Max. Units
Thermal Resistance Junction to
Ambient
θ
θ
θ
θ
Still air
150
140
120
40
°C/W
°C/W
°C/W
°C/W
JA
JA
JA
JC
1 m/s air flow
3 m/s air flow
Thermal Resistance Junction to Case
MDS 1726A B
7
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
MK1726A
Low EMI Clock Generator
Ordering Information
Part / Order Number
Marking
Shipping
packaging
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Package
Temperature
MK1726-01AG
MK1726-01AGTR
MK1726-01AS
MK1726-01ASTR
MK1726-02AG
MK1726-02AGTR
MK1726-02AS
MK1726-02ASTR
MK1726-04AG
1726-01AG
1726-01AG
1726-01AS
1726-01AS
1726-02AG
1726-02AG
1726-02AS
1726-02AS
1726-04AG
1726-04AG
1726-04AS
1726-04AS
8-pin TSSOP
8-pin TSSOP
8-pin SOIC
8-pin SOIC
8-pin TSSOP
8-pin TSSOP
8-pin SOIC
8-pin SOIC
8-pin TSSOP
8-pin TSSOP
8-pin SOIC
8-pin SOIC
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
0 to +85° C
MK1726-04AGTR
MK1726-04AS
MK1726-04ASTR
Tape and Reel
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Inc. (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
MDS 1726A B
8
Revision 101703
Integrated Circuit Systems, Inc. z 525 Race Street, San Jose, CA 95126 z tel (408) 297-1201 z www.icst.com
相关型号:
©2020 ICPDF网 联系我们和版权申明