MPC92439ACR2 [IDT]
Clock Generator, 900MHz, PQFP32, ROHS COMPLIANT, LQFP-32;型号: | MPC92439ACR2 |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Clock Generator, 900MHz, PQFP32, ROHS COMPLIANT, LQFP-32 时钟 外围集成电路 晶体 |
文件: | 总16页 (文件大小:441K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
900MHz, Low Voltage,
LVPECL Clock Synthesizer
MPC92439
Product Discontinuance Notice – Last Time Buy Expires on (12/7/2013)
DATA SHEET
The MPC92439 is a 3.3 V compatible, PLL based clock synthesizer targeted for high
performance clock generation in mid-range to high-performance telecom, networking and
computing applications. With output frequencies from 3.125 MHz to 900 MHz and the
support of differential LVPECL output signals the device meets the needs of the most
demanding clock applications.
900MHZ LOW VOLTAGE
CLOCK SYNTHESIZER
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3.125 MHz to 900 MHz synthesized clock output signal
Differential LVPECL output
LVCMOS compatible control inputs
On-chip crystal oscillator for reference frequency generation
Alternative LVCMOS compatible reference input
3.3V power supply
(1)
FN SUFFIX
28-LEAD PLCC PACKAGE
CASE 776-02
Fully integrated PLL
Minimal frequency overshoot
Serial 3-wire programming interface
Parallel programming interface for power-up
28-PLCC and 32-LQFP packaging
28-Lead and 32-lead Pb-free packages available
SiGe Technology
(2)
EI SUFFIX
28-LEAD PLCC PACKAGE
CASE 776-02
Ambient temperature range 0C to + 70C
Pin and function compatible to the MC12439 and MPC9239
(1)
FA SUFFIX
32-LEAD LQFP PACKAGE
CASE 873A-03
Functional Description
The internal crystal oscillator uses the external quartz crystal as the basis of its frequency
reference. The frequency of the internal crystal oscillator or external reference clock signal is
multiplied by the PLL. The VCO within the PLL operates over a range of 400 to 900 MHz. Its
output is scaled by a divider that is configured by either the serial or parallel interfaces. The
crystal oscillator frequency fXTAL, the PLL feedback-divider M and the PLL post-divider N de-
termine the output frequency.
The feedback path of the PLL is internal. The PLL adjusts the VCO output frequency to
be M times the reference frequency by adjusting the VCO control voltage. Note that for
some values of M (either too high or too low) the PLL will not achieve phase lock. The PLL
will be stable if the VCO frequency is within the specified VCO frequency range (400 to 900
MHz). The M-value must be programmed by the serial or parallel interface.
(2)
AC SUFFIX
32-LEAD LQFP PACKAGE
CASE 873A-03
K SUFFIX
32-LEAD VFQFN PACKAGE
Pb-FREE PACKAGE
The PLL post-divider N is configured through either the serial or the parallel interfaces,
and can provide one of four division ratios (1, 2, 4, or 8). This divider extends performance
of the part while providing a 50% duty cycle. The output driver is driven differentially from
the output divider, and is capable of driving a pair of transmission lines terminated 50 to
Notes:
(1) FN, FA suffix: leaded terminations
(2) EI, AC suffix: lead-free, RoHS-compliant, EPP
VCC – 2.0V. The positive supply voltage for the internal PLL is separated from the power
supply for the core logic and output drivers to minimize noise induced jitter.
ORDERING INFORMATION
The configuration logic has two sections: serial and parallel. The parallel interface uses
the values at the M[6:0] and N[1:0] inputs to configure the internal counters. It is recom-
mended on system reset to hold the P_LOAD input LOW until power becomes valid. On the
LOW-to-HIGH transition of P_LOAD, the parallel inputs are captured. The parallel interface
has priority over the serial interface. Internal pullup resistors are provided on the M[6:0] and
N[1:0] inputs prevent the LVCMOS compatible control inputs from floating. The serial inter-
face centers on a twelve bit shift register. The shift register shifts once per rising edge of the
S_CLOCK input. The serial input S_DATA must meet setup and hold timing as specified in
the AC Characteristics section of this document. The configuration latches will capture the
Device
MPC92439EI
Package
PLCC-28 (Pb-Free)
LQFP-32
MPC92439FA
MPC92439AC
MPC92439KLF
LQFP-32 (Pb-Free)
P R O P OVSFQFEN-32D(Pb-Free)
value of the shift register on the HIGH-to-LOW edge of the S_LOAD input. See PROGRAMMING INTERFACE for more information. The TEST
output reflects various internal node values, and is controlled by the T[2:0] bits in the serial data stream. In order to minimize the PLL jitter, it
is recommended to avoid active signal on the TEST output. The PWR_DOWN pin, when asserted, will synchronously divide the FOUT by 16.
The power down sequence is clocked by the PLL reference clock, thereby causing the frequency reduction to happen relatively slowly. Upon
de-assertion of the PWR_DOWN pin, the FOUT input will step back up to its programmed frequency in four discrete increments.
MPC92439 REVISION 5 FEBRUARY 6, 2013
1
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
XTAL_IN
XTAL_OUT
1
0
XTAL
10 – 20 MHz
1
2
4
8
11
00
01
10
1
16
Ref
VCO
FOUT
FOUT
OE
PLL
400 – 900 MHz
FREF_EXT
0
V
CC
FB
0 TO 127
7-BIT M-DIVIDER
XTAL_SEL
TEST
TEST
2
3
7
V
CC
M-LATCH
N-LATCH
T-LATCH
LE
P_LOAD
S_LOAD
P/S
0
1
0
1
BITS 3-4
BITS 0-2
BITS 11-5
S_DATA
S_CLOCK
12-BIT SHIFT REGISTER
V
CC
M[0:6]
N[1:0]
PWR_DOWN
OE
Figure 1. MPC92439 Logic Diagram
25
24
23 22
21
20 19
S_CLOCK
N[1]
26
27
18
17
16
15
14
24 23 22 21 20 19 18 17
25
26
27
28
29
30
31
32
16
15
14
13
12
11
10
9
NC
GND
S_DATA
S_LOAD
N[0]
M[3]
TEST
NC
28
1
V
V
M[2]
CC
CC
XTAL_SEL
M[6]
V
MPC92439
CC_PLL
M[1]
MPC92439
PWR_DOWN
FREF_EXT
XTAL_IN
2
3
4
GND
M[0]
M[5]
13
12
FOUT
P_LOAD
OE
M[4]
FOUT
5
6
7
8
9
10 11
V
XTAL_OUT
CC
1
2
3
4
5
6
7
8
Figure 2. MPC92439 28-Lead PLCC Pinout
(Top View)
Figure 3. MPC92439 32-Lead Package Pinout
(Top View)
MPC92439 REVISION 5 FEBRUARY 6, 2013
2
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
24 23 22 21 20 19 18 17
25
ND
NC
16
15
14
13
26
TE T
M 3
M 2
VCC 27
MPC92439
28
VCC
ND
M 1
29
30
31
32
12 M 0
11 P L O
D
O
FO
FO
T
T
OE
10
VCC
9
T L
T
1
2
3
4
5
6
7
8
Figure 4. 32-Lead VFQFN Package Pinout (Top View)
MPC92439 REVISION 5 FEBRUARY 6, 2013
3
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Table 1. Pin Configurations
Pin
XTAL_IN, XTAL_OUT
FREF_EXT
I/O
Default
Type
Function
6
0
Analog Crystal oscillator interface
LVCMOS Alternative PLL reference input
LVPECL Differential clock output
LVCMOS Test and device diagnosis output
LVCMOS PLL reference select input
Input
Output
Output
Input
FOUT, FOUT
TEST
XTAL_SEL
1
0
PWR_DOWN
Input
LVCMOS Configuration input for power down mode. Assertion (deassertion) of power down will
decrease (increase) the output frequency by a ratio of 16 in 4 discrete steps.
PWR_DOWN assertion (deassertion) is synchronous to the input reference clock.
S_LOAD
P_LOAD
Input
Input
0
1
LVCMOS Serial configuration control input. This inputs controls the loading of the configuration
latches with the contents of the shift register. The latches will be transparent when this
signal is high, thus the data must be stable on the high-to-low transition.
LVCMOS Parallel configuration control input. this input controls the loading of the configuration
latches with the content of the parallel inputs (M and N). The latches will be
transparent when this signal is low, thus the parallel data must be stable on the low-
to-high transition of P_LOAD. P_LOAD is state sensitive.
S_DATA
S_CLOCK
M[0:6]
Input
Input
Input
0
0
1
LVCMOS Serial configuration data input.
LVCMOS Serial configuration clock input.
LVCMOS Parallel configuration for PLL feedback divider (M).
M is sampled on the low-to-high transition of P_LOAD.
N[1:0]
OE
Input
Input
1
1
LVCMOS Parallel configuration for Post-PLL divider (N).
N is sampled on the low-to-high transition of P_LOAD.
LVCMOS Output enable (active high)
The output enable is synchronous to the output clock to eliminate the possibility of runt
pulses on the FOUT output. OE = L low stops FOUT in the logic low state (FOUT = L,
FOUT = H).
GND
Supply
Supply
Ground Negative power supply (GND).
V
V
Positive power supply for I/O and core. All V pins must be connected to the positive
CC
CC
CC
power supply for correct operation.
V
Supply
V
PLL positive power supply (analog power supply).
CC_PLL
CC
NC
Do not connect
Table 2. Output Frequency Range and PLL Post-Divider N
N
PWR_DOWN
VCO Output Frequency Division
FOUT Frequency Range
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0
0
0
1
1
1
1
2
4
200 - 450 MHz
100 -225 MHz
8
50-112.5 MHz
1
400-900 MHz
32
64
128
16
12.5-28.125 MHz
6.25-14.0625 MHz
3.125-7.03125 MHz
25-56.25 MHz
MPC92439 REVISION 5 FEBRUARY 6, 2013
4
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Table 3. Function Table
Input
XTAL_SEL
OE
0
1
FREF_EXT
XTAL interface
Outputs enabled
Outputs disabled, FOUT is stopped in the logic low state
(FOUT = L, FOUT = H)
PWR_DOWN
Output divider 1
Output divider 16
Table 4. General Specifications
Symbol
Characteristics
Min
Typ
– 2
Max
Unit
V
Condition
V
Output Termination Voltage
ESD Protection (Machine Model)
ESD Protection (Human Body Model)
Latch-Up Immunity
V
TT
CC
MM
HBM
LU
200
2000
200
V
V
mA
pF
C
Input Capacitance
4.0
Inputs
IN
LQFP 32 Thermal Resistance Junction to Ambient
JESD 51-3, single layer test board
JA
83.1
73.3
68.9
63.8
57.4
86.0
75.4
70.9
65.3
59.6
C/W Natural convection
C/W 100 ft/min
C/W 200 ft/min
C/W 400 ft/min
C/W 800 ft/min
JESD 51-6, 2S2P multi-layer test board
59.0
54.4
52.5
50.4
47.8
60.6
55.7
53.8
51.5
48.8
C/W Natural convection
C/W 100 ft/min
C/W 200 ft/min
C/W 400 ft/min
C/W 800 ft/min
P R O P O S E D
Thermal Resistance Junction to Ambient 32 VFQFN
2.5
1
37.6
0
33.7
meters per second
C/W
43.0
LQFP 32 Thermal Resistance Junction to Case
23.0
26.3
C/W MIL-SPEC 883E
JC
Method 1012.1
Table 5. Absolute Maximum Ratings(1)
Symbol
Characteristics
Min
–0.3
–0.3
–0.3
Max
Unit
V
Condition
V
Supply Voltage
4.6
CC
V
DC Input Voltage
DC Output Voltage
DC Input Current
DC Output Current
Storage Temperature
V
+ 0.3
V
IN
CC
CC
V
V
+ 0.3
V
OUT
I
20
mA
mA
C
IN
I
50
OUT
T
–65
125
S
1. Absolute maximum continuous ratings are those maximum values beyond which damage to the device may occur. Exposure to these
conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation at absolute-maximum-rated
conditions is not implied.
MPC92439 REVISION 5 FEBRUARY 6, 2013
5
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Table 6. DC Characteristics (VCC = 3.3V ± 5%, TA = 0°C to +70°C)
Symbol
Characteristics
Min
Typ
Max
Unit
Condition
LVCMOS Control Inputs (FREF_EXT, POWER_DOWN, XTAL_SEL, P_LOAD, S_LOAD, S_DATA, S_CLOCK, M[0:8], N[0:1]. OE)
V
Input High Voltage
Input Low Voltage
2.0
V
+ 0.3
CC
V
V
LVCMOS
LVCMOS
IH
V
0.8
200
IL
(1)
I
A
V
= V or GND
IN
Input Current
IN CC
(2)
Differential Clock Output F
OUT
V
Output High Voltage
Output Low Voltage
V
V
–1.11
V
V
–0.74
V
V
LVPECL
LVPECL
OH
CC
CC
V
–1.95
–1.60
OL
CC
CC
Test and Diagnosis Output TEST
V
Output High Voltage
Output Low Voltage
2.0
V
V
I
I
= –0.8 mA
= 0.8 mA
OH
OH
OL
V
0.55
OL
Supply Current
I
Maximum PLL Supply Current
Maximum Supply Current
20
mA
mA
V
Pins
CC_PLL
CC_PLL
I
62
110
All V Pins
CC
CC
1. Inputs have pull-down resistors affecting the input current.
2. Outputs terminated 50 to V = V – 2V.
TT
CC
Table 7. AC Characteristics (VCC = 3.3 V ± 5%, TA = 0°C to +70°C)(1)
Symbol
Characteristics
Crystal interface frequency range
Min
10
Typ
Max
Unit
MHz
MHz
Condition
f
20
XTAL
(2)
f
400
900
VCO
MAX
VCO frequency range
Output Frequency
f
N = 11 (1)
N = 00 (2)
N = 01 (4)
N = 10 (8)
400
200
100
50
900
450
MHz PWR_DOWN = 0
MHz
MHz
MHz
225
112.5
(3)
f
0
10
MHz
S_CLOCK
Serial Interface Programming Clock Frequency
t
Minimum Pulse Width
Output Duty Cycle
Output Rise/Fall Time
Setup Time
(S-LOAD, P_LOAD)
50
45
ns
%
P,MIN
DC
50
55
t , t
0.05
0.3
ns
20% to 80%
r
f
t
S_DATA to S_CLOCK
S_CLOCK to S_LOAD
M, N to P_LOAD
20
20
20
ns
ns
ns
S
t
Hold Time
S_DATA to S_CLOCK
M, N to P_LOAD
20
20
ns
ns
S
(4)
t
t
12
25
55
65
ps
JIT(CC)
Cycle-to-cycle jitter (RMS 1)
N=11 (÷1)
N=00 (÷2)
N=01 (÷4)
N=10 (÷8)
(5)
13
23
36
40
JIT(CC)
Period jitter (RMS 1)
N=11 (÷1)
N=00 (÷2)
N=01 (÷4)
N=10 (÷8)
t
Maximum PLL Lock Time
10
ms
LOCK
1. AC characteristics apply for parallel output termination of 50 to V
.
TT
2. The input frequency f
and the PLL feedback divider M must match the VCO frequency range: f
= f
· M
XTAL
VCO
XTAL
3. The frequency of S_CLOCK is limited to 10 MHz in serial programming mode. S_CLOCK can be switched at higher frequencies when used
as test clock in test mode 6. See APPLICATIONS INFORMATION for more details.
4. Maximum cycle jitter measured at the lowest VCO frequency. Figure 5 shows the cycle jitter vs. frequency characteristics
5. Maximum period jitter measured at the lowest VCO frequency. Figure 6 shows the period jitter vs. frequency characteristics
MPC92439 REVISION 5 FEBRUARY 6, 2013
6
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Table 8. MPC92439 Frequency Operating Range (in MHz)
Output frequency for f
=16 MHz and for N =
VCO frequency for an crystal interface frequency of
XTAL
M
M[6:0]
10
12
14
16
18
20
1
2
4
8
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
...
0010100
0010101
0010110
0010111
0011000
0011001
0011010
0011011
0011100
0011101
0011110
0011111
0100000
0100001
0100010
0100011
0100100
0100101
0100110
0100111
0101000
0101001
0101010
0101011
0101100
0101101
0101110
0101111
0110000
0110001
0110010
0110011
0110100
0110101
0110110
0110111
0111000
0111001
0111010
0111011
0111100
0111101
0111110
0111111
1000000
400
420
440
460
480
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
800
820
840
860
880
900
414
432
450
468
486
504
522
540
558
576
594
612
630
648
666
684
702
720
738
756
774
792
810
828
846
864
882
900
400
416
432
448
464
480
496
512
528
544
560
576
592
608
624
640
656
672
688
704
720
736
752
768
784
800
816
832
848
864
880
896
400
416
432
448
464
480
496
512
528
544
560
576
592
608
624
640
656
672
688
704
720
736
752
768
784
800
816
832
848
864
880
896
200
208
216
224
232
240
248
256
264
272
280
288
296
304
312
320
328
336
344
352
360
368
376
384
392
400
408
416
424
432
440
448
100
104
108
112
116
120
124
128
132
136
140
144
148
152
156
160
164
168
172
176
180
184
188
192
196
200
204
208
212
216
220
224
50
52
54
56
406
420
434
448
462
476
490
504
518
532
546
560
574
588
602
616
630
644
658
672
684
700
714
728
742
756
770
784
798
812
826
840
854
868
882
896
...
58
60
62
64
66
408
420
432
444
456
468
480
492
504
516
528
540
552
564
576
588
600
612
624
636
648
660
672
684
696
708
720
732
744
756
768
...
68
70
72
74
76
78
400
410
420
430
440
450
460
470
480
490
500
510
520
530
540
550
560
570
580
590
600
610
620
630
640
...
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
MPC92439 REVISION 5 FEBRUARY 6, 2013
7
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
PROGRAMMING INTERFACE
Programming the MPC92439
Substituting N for the four available values for N (1, 2, 4, 8) yields:
Programming the MPC92439 amounts to properly configuring the
internal PLL dividers to produce the desired synthesized frequency
at the output. The output frequency can be represented by this
formula:
Table 9. Output Frequency Range for fXTAL = 16 MHz
N
F
F
Range
F
Step
OUT
OUT
OUT
1
0
0
1
1
0
0
1
0
1
Value
fOUT = fXTAL M N
(1)
2
4
8
1
8M
4M
200-450 MHz
100-225 MHz
50-112.5 MHz
400-900 MHz
8 MHz
4 MHz
2 MHz
16 MHz
where fXTAL is the crystal frequency, M is the PLL feedback-divider
and N is the PLL post-divider. The input frequency and the selection
of the feedback divider M is limited by the VCO-frequency range.
fXTAL and M must be configured to match the VCO frequency range
of 400 to 900 MHz in order to achieve stable PLL operation:
2M
16M
Example Calculation for an 16 MHz Input Frequency
MMIN = fVCO,MIN (fXTAL) and
MMAX = fVCO,MAX (fXTAL
(2)
(3)
For example, if an output frequency of 384 MHz was desired, the
following steps would be taken to identify the appropriate M and N
values. 384 MHz falls within the frequency range set by an N value
of 2, so N[1:0]=00. For N = 2, FOUT = 8M and M = FOUT8.
Therefore, M = 384 8 = 48, so M[6:0] = 0110000. Following this
procedure a user can generate any whole frequency between 50
MHz and 900 MHz. The size of the programmable frequency steps
will be equal to:
)
For instance, the use of a 16 MHz input frequency requires the
configuration of the PLL feedback divider between M = 25 and M =
56. Table 8 shows the usable VCO frequency and M divider range for
other example input frequencies. Assuming that a 16 MHz input
frequency is used, equation (1) reduces to:
fOUT = 16 M N
(4)
fSTEP = fXTAL N
(5)
APPLICATIONS INFORMATION
Jitter Performance of the MPC92439
Figure 5 and Figure 6 illustrate the RMS jitter performance of the
MPC92439 across its specified VCO frequency range. The cycle-to-
cycle and period jitter is a function of the VCO frequency and the
output divider N. The general trend is that as the output frequency
increases (higher VCO frequency and lower N-divider) the
MPC92439 output jitter decreases. Optimum jitter performance can
be achieved at higher VCO and output frequencies. The maximum
cycle-to-cycle and period jitter published in Table 7 correspond to the
jitter performance at the lowest VCO frequency limit).
Figure 6. MPC92439 Period Jitter
Using the Parallel and Serial Interface
The M and N counters can be loaded either through a parallel or
serial interface. The parallel interface is controlled via the P_LOAD
signal such that a LOW to HIGH transition will latch the information
present on the M[6:0] and N[1:0] inputs into the M and N counters.
When the P_LOAD signal is LOW the input latches will be
transparent and any changes on the M[6:0] and N[1:0] inputs will
affect the FOUT output pair. To use the serial port the S_CLOCK
signal samples the information on the S_DATA line and loads it into
a 12 bit shift register. Note that the P_LOAD signal must be HIGH for
the serial load operation to function. The Test register is loaded with
the first three bits, the N register with the next two, and the M register
with the final eight bits of the data stream on the S_DATA input. For
each register the most significant bit is loaded first (T2, N1 and M6).
A pulse on the S_LOAD pin after the shift register is fully loaded will
transfer the divide values into the counters. The HIGH to LOW
Figure 5. MPC92439 Cycle-to-cycle Jitter
MPC92439 REVISION 5 FEBRUARY 6, 2013
8
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
transition on the S_LOAD input will latch the new divide values into
the counters. Figure 7 illustrates the timing diagram for both a
parallel and a serial load of the MPC92439 synthesizer.
M[6:0] and N[1:0] are normally specified once at power-up
through the parallel interface, and then possibly again through the
serial interface. This approach allows the application to come up at
one frequency and then change or fine-tune the clock as the ability
to control the serial interface becomes available.
the user more control on the test clocks sent through the clocktree
shows the functional setup of the PLL bypass mode. Because the
S_CLOCK is a CMOS level the input frequency is limited to 200
MHz. This means the fastest the FOUT pin can be toggled via the
S_CLOCK is 100 MHz as the divide ratio of the Post-PLL divider is
2 (if N = 1). Note that the M counter output on the TEST output will
not be a 50% duty cycle.
Table 10. Test and Debug Configuration for TEST
Using the Test and Diagnosis Output TEST
T[2:0]
TEST Output
The TEST output provides visibility for one of the several internal
nodes as determined by the T[2:0] bits in the serial configuration
stream. It is not configurable through the parallel interface. Although
it is possible to select the node that represents FOUT, the LVCMOS
output is not able to toggle fast enough for higher output frequencies
and should only be used for test and diagnosis.
T2
T1
T0
(1)
0
0
0
12-bit shift register out
Logic 1
0
0
0
1
1
0
f
2
XTAL
0
1
1
1
1
1
0
0
1
1
1
0
1
0
1
M-Counter out
FOUT
The T2, T1 and T0 control bits are preset to ‘000' when P_LOAD
is LOW so that the PECL FOUT outputs are as jitter-free as possible.
Any active signal on the TEST output pin will have detrimental
affects on the jitter of the PECL output pair. In normal operations,
jitter specifications are only guaranteed if the TEST output is static.
The serial configuration port can be used to select one of the
alternate functions for this pin.
Logic 0
M-Counter out in PLL-bypass mode
FOUT 4
1. Clocked out at the rate of S_CLOCK\
Most of the signals available on the TEST output pin are useful
only for performance verification of the MPC92439 itself. However,
the PLL bypass mode may be of interest at the board level for
functional debug. When T[2:0] is set to 110 the MPC92439 is placed
in PLL bypass mode. In this mode the S_CLOCK input is fed directly
into the M and N dividers. The N divider drives the FOUT differential
pair and the M counter drives the TEST output pin. In this mode the
S_CLOCK input could be used for low speed board level functional
test or debug. Bypassing the PLL and driving FOUT directly gives
Table 11. Debug Configuration for PLL Bypass(1)
Output
FOUT
TEST
Configuration
S_CLOCK N
(2)
M-Counter out
1. T[2:0] = 110. AC specifications do not apply in PLL bypass
mode
2. Clocked out at the rate of S_CLOCK (2N)
S_CLOCK
T2 T1 T0 N1 N0 M6 M5 M4 M3 M2 M1 M0
S_DATA
S_LOAD
First
Bit
Last
Bit
M[6:0]
N[1:0]
M,
N
P_LOAD
Figure 7. Serial Interface Timing Diagram
isolation is sufficient. However, in a digital system environment
Power Supply Filtering
where it is more difficult to minimize noise on the power supplies a
second level of isolation may be required. The simplest form of
isolation is a power supply filter on the VCC_PLL pin for the
MPC92439. Figure 8 illustrates a typical power supply filter scheme.
The MPC92439 is most susceptible to noise with spectral content in
the 1 kHz to 1 MHz range. Therefore, the filter should be designed
to target this range. The key parameter that needs to be met in the
final filter design is the DC voltage drop that will be seen between
The MPC92439 is a mixed analog/digital product. Its analog
circuitry is naturally susceptible to random noise, especially if this
noise is seen on the power supply pins. Random noise on the
VCC_PLL pin impacts the device characteristics. The MPC92439
provides separate power supplies for the digital circuitry (VCC) and
the internal PLL (VCC_PLL) of the device. The purpose of this design
technique is to try and isolate the high switching noise digital outputs
from the relatively sensitive internal analog phase-locked loop. In a
controlled environment such as an evaluation board, this level of
MPC92439 REVISION 5 FEBRUARY 6, 2013
9
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
the VCC supply and the MPC92439 pin of the MPC92439. From the
data sheet, the VCC_PLL current (the current sourced through the
VCC_PLL pin) is maximum 20 mA, assuming that a minimum of
2.835 V must be maintained on the VCC_PLL pin. The resistor shown
in Figure 8 must have a resistance of 10–15 to meet the voltage
drop criteria. The RC filter pictured will provide a broadband filter with
approximately 100:1 attenuation for noise whose spectral content is
above 20 kHz. As the noise frequency crosses the series resonant
point of an individual capacitor its overall impedance begins to look
inductive and thus increases with increasing frequency. The parallel
capacitor combination shown ensures that a low impedance path to
ground exists for frequencies well above the bandwidth of the PLL.
Generally, the resistor/capacitor filter will be cheaper, easier to
implement and provide an adequate level of supply filtering. A higher
level of attenuation can be achieved by replacing the resistor with an
appropriate valued inductor. A 1000 H choke will show a significant
impedance at 10 kHz frequencies and above. Because of the current
draw and the voltage that must be maintained on the VCC_PLL pin, a
low DC resistance inductor is required (less than 15 ).
degraded due to system power supply noise. The power supply filter
and bypass schemes discussed in this section should be adequate
to eliminate power supply noise related problems in most designs.
C1
C1
1
CF
C2
XTAL
= V
CC
R = 10-15
F
= GND
= Via
V
V
CC_PLL
CC
C
C = 22 F
2
F
MPC92439
Figure 9. PCB Board Layout Recommendation
for the PLCC28 Package
V
CC
C , C = 0.01...0.1 F
C
1
2
1
The On-Chip Crystal Oscillator
The MPC92439 features an integrated on-chip crystal oscillator to
minimize system implementation cost. The integrated oscillator is a
Pierce-type that uses the crystal in its parallel resonance mode. It is
recommended to use a 10 to 20 MHz crystal with a load specification
of CL = 10 pF. Crystals with a load specification of CL = 20 pF may be
used at the expense of an slightly higher frequency than specified for
the crystal. Externally connected capacitors on both the XTAL_IN
and XTAL_OUT pins are not required but can be used to fine-tune the
crystal frequency as desired.
The crystal, the trace and optional capacitors should be placed on
the board as close as possible to the MPC92439 XTAL_IN and
XTAL_OUT pins to reduce crosstalk of active signals into the
oscillator. Short and wide traces further reduce parasitic inductance
and resistance. It is further recommended to guard the crystal circuit
by placing a ground ring around the traces and oscillator
Figure 8. VCC_PLL Power Supply Filter
Layout Recommendations
The MPC92439 provides sub-nanosecond output edge rates and
thus a good power supply bypassing scheme is a must. Figure 9
shows a representative board layout for the MPC92439. There exists
many different potential board layouts and the one pictured is but
one. The important aspect of the layout in Figure 9 is the low
impedance connections between VCC and GND for the bypass
capacitors. Combining good quality general purpose chip capacitors
with good PCB layout techniques will produce effective capacitor
resonances at frequencies adequate to supply the instantaneous
switching current for the MPC92439 outputs. It is imperative that low
inductance chip capacitors are used; it is equally important that the
board layout does not introduce back all of the inductance saved by
using the leadless capacitors. Thin interconnect traces between the
capacitor and the power plane should be avoided and multiple large
vias should be used to tie the capacitors to the buried power planes.
Fat interconnect and large vias will help to minimize layout induced
inductance and thus maximize the series resonant point of the
bypass capacitors. Note the dotted lines circling the crystal oscillator
connection to the device. The oscillator is a series resonant circuit
and the voltage amplitude across the crystal is relatively small. It is
imperative that no actively switching signals cross under the crystal
as crosstalk energy coupled to these lines could significantly impact
the jitter of the device. Special attention should be paid to the layout
of the crystal to ensure a stable, jitter free interface between the
crystal and the on-board oscillator. Although the MPC92439 has
several design features to minimize the susceptibility to power supply
noise (isolated power and grounds and fully differential PLL), there
still may be applications in which overall performance is being
components. See Table 12 for recommended crystal specifications.
Table 12. Recommended Crystal Specifications
Parameter
Value
Fundamental AT Cut
Parallel
Crystal Cut
Resonance Mode
Crystal Frequency
Shunt Capacitance C
10 - 20 MHz
5 - 7 pF
0
Load Capacitance C
10 pF
L
Equivalent Series Resistance ESR
20–60
MPC92439 REVISION 5 FEBRUARY 6, 2013
10
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
As an alternative to parallel resonance mode crystals, the
oscillator also works with crystals specified in the series resonance
mode. With series resonance crystals, the oscillator frequency and
the synthesized output frequency of the MPC92439 will be a
approximately 350-400 ppm higher than using crystals specified for
parallel frequency mode. This is applicable to applications using the
MPC92439 in sockets designed for the pin and function compatible
MC12439 synthesizer, which has an oscillator using the crystal in its
series resonance mode.Table 13 shows the recommended
specifications for series resonance mode crystals
Table 13. Alternative Crystal Specifications
Parameter
Value
Fundamental AT Cut
Series
Crystal Cut
Resonance Mode
Crystal Frequency
Shunt Capacitance C
10 - 20 MHz
5 - 7 pF
0
Equivalent Series Resistance ESR
50–80
MPC92439 REVISION 5 FEBRUARY 6, 2013
11
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Package Outline and Package Dimensions
PACKAGE DIMENSIONS
CASE 776-02
ISSUE D
PLCC PLASTIC PACKAGE
MPC92439 REVISION 5 FEBRUARY 6, 2013
12
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
PACKAGE DIMENSIONS
4X
0.20
H
A-B D
6
D1
3
A, B, D
e/2
D1/2
32
PIN 1 INDEX
1
25
F
F
A
B
E1/2
6
E1
E
4
DETAIL G
E/2
DETAIL G
8
17
NOTES:
9
7
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994.
3. DATUMS A, B, AND D TO BE DETERMINED AT
DATUM PLANE H.
D
4
D/2
4X
D
4. DIMENSIONS D AND E TO BE DETERMINED AT
SEATING PLANE C.
0.20
C
A-B D
5. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED
THE MAXIMUM b DIMENSION BY MORE THAN
0.08-mm. DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSION AND ADJACENT LEAD OR
PROTRUSION: 0.07-mm.
H
28X
e
32X
0.1 C
6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.25-mm PER SIDE. D1 AND E1 ARE MAXIMUM
PLASTIC BODY SIZE DIMENSIONS INCLUDING
MOLD MISMATCH.
7. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
8. THESE DIMENSIONS APPLY TO THE FLAT
SECTION OF THE LEAD BETWEEN 0.1-mm AND
0.25-mm FROM THE LEAD TIP.
SEATING
PLANE
C
DETAIL AD
BASE
METAL
PLATING
b1
c
c1
MILLIMETERS
DIM
A
A1
A2
b
b1
c
c1
D
MIN
1.40
0.05
1.35
0.30
0.30
0.09
0.09
MAX
1.60
0.15
1.45
0.45
0.40
0.20
0.16
b
5
8
8X (θ1˚)
M
0.20
C
A-B
D
R R2
SECTION F-F
R R1
9.00 BSC
D1
e
E
E1
L
L1
q
q1
R1
R2
S
7.00 BSC
0.80 BSC
9.00 BSC
7.00 BSC
A2
A
0.25
GAUGE PLANE
0.50
1.00 REF
0˚ 7˚
12 REF
0.70
(S)
A1
L
θ˚
0.08
0.08
0.20
---
(L1)
0.20 REF
DETAIL AD
CASE 873A-03
ISSUE B
LQFP PLASTIC PACKAGE
MPC92439 REVISION 5 FEBRUARY 6, 2013
13
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Package Outline - K Suffix for 32 Lead VFQFN
Seating Plane
(Ref.)
N & N
(N -1)x e
(Ref.)
Even
A1
IndexArea
L
A3
E2
e
2
N
N
(Ty p.)
If N & N
are Even
Anvil
1
Singulation
2
or
(N -1)x e
(Ref.)
Sawn
E2
2
Singulation
TopView
D
b
(Ref.)e
N &N
Odd
Thermal
Base
A
D2
2
0. 08
C
Chamfer 4x
0.6 x 0.6 max
OPTIONAL
D2
C
Bottom View w/Type A ID
Bottom View w/Type C ID
2
1
2
1
CHAMFER
4
RADIUS
N N-1
N N-1
4
There are 2 methods of indicating pin 1 corner at the back of the VFQFN package:
1. Type A: Chamfer on the paddle (near pin 1)
2. Type C: Mouse bite on the paddle (near pin 1)
NOTE: The following package mechanical drawing is a generic
Table 14. Package Dimensions
drawing that applies to any pin count VFQFN package. This drawing
is not intended to convey the actual pin count or pin layout of this
device. The pin count and pinout are shown on the front page. The
package dimensions are in Table 14.
JEDEC Variation: VHHD-2/-4
All Dimensions in Millimeters
Symbol
Minimum
Nominal
Maximum
N
A
32
0.80
0
1.00
0.05
A1
A3
b
0.25 Ref.
0.25
0.18
0.30
8
N
D & NE
D & E
5.00 Basic
D2 & E2
3.0
3.3
e
L
0.50 Basic
0.40
0.30
0.50
Reference Document: JEDEC Publication 95, MO-220
MPC92439 REVISION 5 FEBRUARY 6, 2013
14
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
Revision History Sheet
Rev
5
Table
Page
Description of Change
Date
10/19/2012
2/6/2013
6
6
1
Per PCN N0611-01, changed Minimum VOH = VCC - 1.02V to VCC - 1.11V.
Product Discontinuance Notice – Last Time Buy Expires on (12/7/2013)
5
MPC92439 REVISION 5 FEBRUARY 6, 2013
15
©2013 Integrated Device Technology, Inc.
MPC92439 Data Sheet
900MHZ, LOW VOLTAGE, LVPECL CLOCK SYNTHESIZER
We’ve Got Your Timing Solution
6024 Silver Creek Valley Road Sales
Technical Support
800-345-7015 (inside USA)
netcom@idt.com
San Jose, California 95138
+408-284-8200 (outside USA) +480-763-2056
Fax: 408-284-2775
www.IDT.com/go/contactIDT
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document,
including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not
guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the
suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any
license under intellectual property rights of IDT or any third parties.
IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to signifi-
cantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third
party owners.
Copyright 2013. All rights reserved.
相关型号:
MPC92469AC
400MHz, OTHER CLOCK GENERATOR, PQFP32, 7 X 7 MM, 1.40 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, MS-026BBA, LQFP-32
NXP
©2020 ICPDF网 联系我们和版权申明