1ED020I12FA2 [INFINEON]
EiceDRIVER™ 汽车 - 电流隔离式单通道 IGBT 驱动器 IC;
| 型号： | 1ED020I12FA2 |
| 厂家： | 
Infineon |
| 描述： | EiceDRIVER™ 汽车 - 电流隔离式单通道 IGBT 驱动器 IC 驱动 双极性晶体管 驱动器 |
| 文件： | 总27页 (文件大小：998K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1ED020I12FA2
Single IGBT Driver IC
SP001080574
1
Overview
Main Features
•
•
•
•
•
Single channel isolated IGBT Driver
For 600V/1200V IGBTs
2 A rail-to-rail output
Vcesat-detection
Active Miller Clamp
Product Highlights
•
•
•
•
•
•
Coreless transformer isolated driver
Basic insulation according to DIN EN 60747-5-2
Basic insulation recognized under UL 1577
Integrated protection features
Suitable for operation at high ambient temperature
AEC Qualified
Typical Application
•
•
•
Drive inverters for HEV and EV
Auxiliary inverters for HEV and EV
High Power DC/DC inverters
Description
The 1ED020I12FA2 is a galvanic isolated single channel IGBT driver in PG-DSO-20 package that provides an
output current capability of typically 2A.
All logic pins are 5V CMOS compatible and could be directly connected to a microcontroller.
The data transfer across galvanic isolation is realized by the integrated Coreless Transformer Technology.
The 1ED020I12FA2 provides several protection features like IGBT desaturation protection, active Miller clamping
and active shut down.
Type
Package
Marking
1ED020I12FA2
PG-DSO-20
1ED020I12FA2
Data Sheet
www.infineon.com
1
Rev. 3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Table of Contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
3
3.1
3.2
Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.4
4.5
4.6
4.6.1
4.6.2
4.6.3
4.7
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Internal Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Undervoltage Lockout (UVLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
READY Status Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Active Shut-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Non-Inverting and Inverting Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Driver Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
External Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
5.1
5.2
5.3
Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recommended Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Logic Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Active Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.4.6
5.4.7
5.4.8
6
Insulation Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Certified according to DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation . . . . . . . . . . 21
Recognized under UL 1577 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1
6.2
6.3
7
8
Timing Diagramms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9
9.1
9.2
Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Reference Layout for Thermal Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Printed Circuit Board Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Data Sheet
2
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Block Diagram 1ED020I12FA2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PG-DSO-20 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Application Example Bipolar Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Application Example Unipolar Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Propagation Delay, Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Typical Switching Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DESAT Switch-Off Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
UVLO Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PG-DSO-20 (Plastic (Green) Dual Small Outline Package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 10 Reference Layout for Thermal Data (Copper thickness 102 μm) . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Data Sheet
3
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recommended Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Logic Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Active Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
According to DIN EN 60747-5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Recognized under UL 1577 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Data Sheet
4
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Block Diagram
2
Block Diagram
VCC1
IN+
VCC2
18
13
UVLO
UVLO
6
8
&
K4
2V
delay
CLAMP
&
delay
TX
RX
1
VCC1
VCC2
VEE2
IN-
14
15
&
VCC1
OUT
NC
7
5
3
RDY
&
/RDY
VEE2
DECODER
RX
TX
ENCODER
&
1
VCC2
VCC1
I3
&
K3
/FLT
DESAT
16
17
≥1
S
9V
FLT Q
1
R
≥1
VCC1
GND2
4
RST
2
/RST
delay
1
VEE2
1ED020I12FA2
1
11
12
19
20
1
2
9
10
GND1
GND1
GND1
GND1
VEE2
VEE2
VEE2
VEE2
Figure 1
Block Diagram 1ED020I12FA2
Data Sheet
5
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Pin Configuration and Functionality
3
Pin Configuration and Functionality
3.1
Pin Configuration
Table 1
Pin Configuration
Pin No. Name
Function
1
VEE2
VEE2
DESAT
GND2
NC
Negative power supply output side
Negative power supply output side
Desaturation protection
Signal ground output side
Not connected
2
3
4
5
6
VCC2
OUT
Positive power supply output side
Driver output
7
8
CLAMP
VEE2
VEE2
GND1
GND1
IN+
Miller clamping
9
Negative power supply output side
Negative power supply output side
Ground input side
10
11
12
13
14
15
16
17
18
19
20
Ground input side
Non inverted driver input
Inverted driver input
IN-
RDY
Ready output
/FLT
Fault output, low active
Reset input, low active
Positive power supply input side
Ground input side
/RST
VCC1
GND1
GND1
Ground input side
Data Sheet
6
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Pin Configuration and Functionality
VEE2
VEE2
DESAT
GND2
NC
GND1
GND1
VCC1
1
2
20
19
18
3
4
/RST 17
/FLT 16
RDY 15
IN- 14
5
6
VCC2
OUT
7
CLAMP
VEE2
VEE2
IN+
GND1
GND1
8
13
12
11
9
10
Figure 2
PG-DSO-20 (top view)
3.2
Pin Functionality
GND1
Ground connection of the input side.
IN+ Non Inverting Driver Input
IN+ control signal for the driver output if IN- is set to low. (The IGBT is on if IN+ = high and IN- = low)
A minimum pulse width is defined to make the IC robust against glitches at IN+. An internal Pull-Down-Resistor
ensures IGBT Off-State.
IN- Inverting Driver Input
IN- control signal for driver output if IN+ is set to high. (IGBT is on if IN- = low and IN+ = high)
A minimum pulse width is defined to make the IC robust against glitches at IN-. An internal Pull-Up-Resistor
ensures IGBT Off-State.
/RST Reset Input
Function 1: Enable/shutdown of the input chip. (The IGBT is off if /RST = low). A minimum pulse width is
defined to make the IC robust against glitches at /RST.
Function 2: Resets the DESAT-FAULT-state of the chip if /RST is low for a time TRST. An internal Pull-Up-Resistor
is used to ensure /FLT status output.
/FLT Fault Output
Open-drain output to report a desaturation error of the IGBT (FLT is low if desaturation occurs)
Data Sheet
7
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Pin Configuration and Functionality
RDY Ready Status
Open-drain output to report the correct operation of the device (RDY = high if both chips are above the UVLO
level and the internal chip transmission is faultless).
VCC1
5 V power supply of the input chip
VEE2
Negative power supply pins of the output chip. If no negative supply voltage is available, all VEE2 pins have to
be connected to GND2.
DESAT Desaturation Detection Input
Monitoring of the IGBT saturation voltage (VCE) to detect desaturation caused by short circuits. If OUT is high,
VCE is above a defined value and a certain blanking time has expired, the desaturation protection is activated
and the IGBT is switched off. The blanking time is adjustable by an external capacitor.
CLAMP Miller Clamping
Ties the gate voltage to ground after the IGBT has been switched off at a defined voltage to avoid a parasitic
switch-on of the IGBT.During turn-off, the gate voltage is monitored and the clamp output is activated when
the gate voltage goes below 2 V below VEE2.
GND2 Reference Ground
Reference ground of the output chip.
OUT Driver Output
Output pin to drive an IGBT. The voltage is switched between VEE2 and VCC2. In normal operating mode Vout
is controlled by IN+, IN- and /RST. During error mode (UVLO, internal error or DESAT) Vout is set to VEE2
independent of the input control signals.
VCC2
Positive power supply pin of the output side.
Data Sheet
8
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Functional Description
4
Functional Description
4.1
Introduction
The 1ED020I12FA2 is an advanced IGBT gate driver that can be also used for driving power MOS devices.
Control and protection functions are included to make possible the design of high reliability systems.
The device consists of two galvanic separated parts. The input chip can be directly connected to a standard
5 V DSP or microcontroller with CMOS in/output and the output chip is connected to the high voltage side.
The rail-to-rail driver output enables the user to provide easy clamping of the IGBTs gate voltage during short
circuit of the IGBT. So an increase of short circuit current due to the feedback via the Miller capacitance can be
avoided. Further, a rail-to-rail output reduces power dissipation.
The device also includes IGBT desaturation protection with FAULT status output.
The READY status output reports if the device is supplied and operates correctly.
+5V
+15V
VCC1
GND1
VCC2
100n
1µ
1k
DESAT
CLAMP
OUT
SGND
IN+
10R
IN+
NC
GND2
VEE2
IN-
220p
RDY
FLT
RST
RDY
/FLT
/RST
1µ
-8V
Figure 3
Application Example Bipolar Supply
4.2
Supply
The driver 1ED020I12FA2 is designed to support two different supply configurations, bipolar supply and
unipolar supply.
In bipolar supply the driver is typically supplied with a positive voltage of 15V at VCC2 and a negative voltage
of -8V at VEE2, please refer to Figure 3. Negative supply prevents a dynamic turn on due to the additional
charge which is generated from IGBT input capacitance times negative supply voltage. If an appropriate
negative supply voltage is used, connecting CLAMP to IGBT gate is redundant and therefore typically not
necessary.
For unipolar supply configuration the driver is typically supplied with a positive voltage of 15V at VCC2.
Erratically dynamic turn on of the IGBT could be prevented with active Miller clamp function, so CLAMP output
is directly connected to IGBT gate, please refer to Figure 4.
Data Sheet
9
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Functional Description
10R
+5V
+15V
VCC1
GND1
VCC2
1µ
100n
1k
DESAT
CLAMP
OUT
SGND
IN+
10R
IN+
NC
GND2
VEE2
IN-
220p
RDY
FLT
RST
RDY
/FLT
/RST
Figure 4
Application Example Unipolar Supply
4.3
Internal Protection Features
4.3.1
Undervoltage Lockout (UVLO)
To ensure correct switching of IGBTs the device is equipped with an undervoltage lockout for both chips, refer
to Figure 8.
If the power supply voltage VVCC1 of the input chip drops below VUVLOL1 a turn-off signal is sent to the output
chip before power-down. The IGBT is switched off and the signals at IN+ and IN- are ignored as long as VVCC1
reaches the power-up voltage VUVLOH1
.
If the power supply voltage VVCC2 of the output chip goes down below VUVLOL2 the IGBT is switched off and
signals from the input chip are ignored as long as VVCC2 reaches the power-up voltage VUVLOH2. VEE2 is not
monitored, otherwise negative supply voltage range from 0 V to -12 V would not be possible.
4.3.2
READY Status Output
The READY output shows the status of three internal protection features.
•
•
•
UVLO of the input chip
UVLO of the output chip after a short delay
Internal signal transmission after a short delay
It is not necessary to reset the READY signal since its state only depends on the status of the former mentioned
protection signals.
4.3.3
Watchdog Timer
During normal operation the internal signal transmission is monitored by a watchdog timer. If the
transmission fails for a given time, the IGBT is switched off and the READY output reports an internal error.
Data Sheet
10
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Functional Description
4.3.4
Active Shut-Down
The Active Shut-Down feature ensures a safe IGBT off-state if the output chip is not connected to the power
supply, IGBT gate is clamped at OUT to VEE2.
4.4
Non-Inverting and Inverting Inputs
There are two possible input modes to control the IGBT. At non-inverting mode IN+ controls the driver output
while IN- is set to low. At inverting mode IN- controls the driver output while IN+ is set to high, please see
Figure 6. A minimum input pulse width is defined to filter occasional glitches.
4.5
Driver Output
The output driver sections uses only MOSFETs to provide a rail-to-rail output. This feature permits that tight
control of gate voltage during on-state and short circuit can be maintained as long as the drivers supply is
stable. Due to the low internal voltage drop, switching behaviour of the IGBT is predominantly governed by
the gate resistor. Furthermore, it reduces the power to be dissipated by the driver.
4.6
External Protection Features
4.6.1
Desaturation Protection
A desaturation protection ensures the protection of the IGBT at short circuit. When the DESAT voltage goes up
and reaches 9 V, the output is driven low. Further, the FAULT output is activated, please refer to Figure 7. A
programmable blanking time is used to allow enough time for IGBT saturation. Blanking time is provided by a
highly precise internal current source and an external capacitor.
4.6.2
Active Miller Clamp
In a half bridge configuration the switched off IGBT tends to dynamically turn on during turn on phase of the
opposite IGBT. A Miller clamp allows sinking the Miller current across a low impedance path in this high dV/dt
situation. Therefore in many applications, the use of a negative supply voltage can be avoided.
During turn-off, the gate voltage is monitored and the clamp output is activated when the gate voltage goes
below typical 2 V (related to VEE2). The clamp is designed for a Miller current up to 2 A.
4.6.3
Short Circuit Clamping
During short circuit the IGBTs gate voltage tends to rise because of the feedback via the Miller capacitance. An
additional protection circuit connected to OUT and CLAMP limits this voltage to a value slightly higher than
the supply voltage. A current of maximum 500 mA for 10 μs may be fed back to the supply through one of this
paths. If higher currents are expected or a tighter clamping is desired external Schottky diodes may be added.
4.7
RESET
The reset inputs have two functions.
Firstly, /RST is in charge of setting back the FAULT output. If /RST is low longer than a given time, /FLT will be
cleared at the rising edge of /RST, refer to Figure 7; otherwise, it will remain unchanged. Moreover, it works as
enable/shutdown of the input logic, refer to Figure 6.
Data Sheet
11
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5
Electrical Parameters
5.1
Absolute Maximum Ratings
Note:
Absolute maximum ratings are defined as ratings, which when being exceeded may lead to
destruction of the integrated circuit. Unless otherwise noted all parameters refer to GND1.
Table 2
Absolute Maximum Ratings
Parameter
Symbol
Values
Max.
Unit
Note
Min.
-0.3
-12
–
1)
1)
Positive power supply output side
Negative power supply output side
VVCC2
VVEE2
20
0.3
28
V
V
V
Maximum power supply voltage output side Vmax2
(VVCC2 - VVEE2
–
)
Gate driver output
VOUT
IOUT
IOUT
VVEE2-0.3 VVCC2+0.3
V
A
A
–
Gate driver high output maximum current
–
–
2.4
2.4
t = 2 µs
t = 2 µs
Gate & Clamp driver low output maximum
current
Maximum short circuit clamping time
tCLP
–
10
μs
ICLAMP/OUT =
500 mA
Positive power supply input side
VVCC1
-0.3
-0.3
6.5
6.5
V
V
–
–
Logic input voltages
(IN+,IN-,RST)
VLogicIN
Opendrain Logic output voltage (FLT)
Opendrain Logic output voltage (RDY)
Opendrain Logic output current (FLT)
Opendrain Logic output current (RDY)
Pin DESAT voltage
VFLT#
VRDY
-0.3
-0.3
–
6.5
6.5
10
V
–
–
–
V
IFLT#
mA
mA
IRDY
–
10
–
1)
VDESAT
VCLAMP
-0.3
-0.3
VVCC2 +0.3 V
3)
Pin CLAMP voltage
VVCC2
+0.32)
V
Junction temperature
TJ
-40
-55
–
150
150
100
700
139
117
1
°C
–
–
Storage temperature
TS
°C
Power dissipation, per input part
Power dissipation, per output part
Thermal resistance (Input part)
Thermal resistance (Output chip active)
ESD Capability
PD, IN
PD, OUT
RTHJA,IN
RTHJA,OUT
VESD
mW
mW
K/W
K/W
kV
4)@TA = 25°C
4) @TA = 25°C
4) @TA = 25°C
4) @TA = 25°C
–
–
–
–
Human Body
Model5)
1) With respect to GND2.
2) May be exceeded during short circuit clamping.
Data Sheet
12
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
3) With respect to VEE2.
4) Output IC power dissipation is derated linearly at 8.5 mW/°C above 68°C. Input IC power dissipation does not require
derating. See Figure 10 for reference layouts for these thermal data. Thermal performance may change significantly
with layout and heat dissipation of components in close proximity.
5) According to EIA/JESD22-A114-B (discharging a 100 pF capacitor through a 1.5 kΩ series resistor).
5.2
Operating Parameters
Note:
Within the operating range the IC operates as described in the functional description. Unless
otherwise noted all parameters refer to GND1.
Table 3
Operating Parameters
Parameter
Symbol
Values
Max.
Unit
Note
Min.
13
1)
1)
Positive power supply output side VVCC2
Negative power supply output side VVEE2
20
0
V
V
V
-12
–
Maximum power supply voltage
output side
Vmax2
28
–
(VVCC2 - VVEE2
)
Positive power supply input side
VVCC1
4.5
5.5
5.5
V
V
–
–
Logic input voltages
(IN+,IN-,RST)
VLogicIN
-0.3
2)
Pin CLAMP voltage
Pin DESAT voltage
Pin TLSET voltage
Ambient temperature
VCLAMP
VDESAT
VTLSET
TA
VVEE2-0.3
-0.3
-0.3
-40
VVCC2
VVCC2
VVCC2
125
V
–
1)
V
1)
V
°C
–
Common mode transient
|DVISO/dt|
–
50
kV/μs
@ 500 V
immunity3)
1) With respect to GND2.
2) May be exceeded during short circuit clamping.
3) The parameter is not subject to production test - verified by design/characterization
5.3
Recommended Operating Parameters
Note:
Unless otherwise noted all parameters refer to GND1.
Table 4
Recommended Operating Parameters
Parameter
Symbol
Value
15
Unit
Note
1)
Positive power supply output side VVCC2
Negative power supply output side VVEE2
V
V
V
1)
-8
Positive power supply input side
1) With respect to GND2.
VVCC1
5
–
Data Sheet
13
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5.4
Electrical Characteristics
Note:
The electrical characteristics include the spread of values in supply voltages, load and junction
temperatures given below. Typical values represent the median values at TA = 25°C. Unless
otherwise noted all voltages are given with respect to their respective GND (GND1 for pins 9 to 16,
GND2 for pins 1 to 8).
5.4.1
Voltage Supply
Table 5
Voltage Supply
Parameter
Symbol
Values
Typ.
Unit
Note
Min.
–
Max.
4.3
–
UVLO Threshold Input VUVLOH1
Chip
4.1
3.8
–
V
V
V
–
–
–
VUVLOL1
3.5
0.15
UVLO Hysteresis Input VHYS1
–
Chip (VUVLOH1 - VUVLOL1
)
UVLO Threshold Output VUVLOH2
–
12.0
11.0
0.9
12.6
V
V
V
–
–
–
Chip
VUVLOL2
10.4
0.7
–
–
UVLO Hysteresis Output VHYS2
Chip (VUVLOH1 - VUVLOL1
)
Quiescent Current Input IQ1
–
7
9
mA
VVCC1 = 5 V
Chip
IN+ = High,
IN- = Low
=>OUT = High,
RDY = High,
/FLT = High
Quiescent Current
Output Chip
IQ2
–
4
6
mA
VVCC2 = 15 V
VVEE2 = -8 V
IN+ = High,
IN- = Low
=>OUT = High,
RDY = High,
/FLT = High
Data Sheet
14
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5.4.2
Logic Input and Output
Table 6
Logic Input and Output
Symbol
Parameter
Values
Typ.
Unit
V
Note
–
Min.
–
Max.
1.5
IN+,IN-, RST Low Input Voltage VIN+L
VIN-L
VRSTL#
IN+,IN-, RST High Input Voltage VIN+H
VIN-H
,
,
–
,
,
3.5
–
–
–
V
–
VRSTH#
IN-, RST Input Current
IIN-, IRST#
-400
–
-100
μA
VIN- = GND1
VRST# = GND1
IN+ Input Current
IIN+
,
100
400
–
μA
μA
VIN+ = VCC1
RDY,FLT Pull Up Current
IPRDY, IPFLT# -400
-100
VRDY = GND1
VFLT# = GND1
Input Pulse Suppression IN+, TMININ+
IN- TMININ-
,
30
40
40
–
–
–
–
ns
ns
ns
–
–
–
Input Pulse Suppression RST TMINRST
for ENABLE/SHUTDOWN
30
Pulse Width RST
for Reseting FLT
TRST
800
FLT Low Voltage
RDY Low Voltage
VFLTL
VRDYL
–
–
–
–
300
300
mV
mV
ISINK(FLT#) = 5 mA
ISINK(RDY) = 5 mA
Data Sheet
15
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5.4.3
Gate Driver
Table 7
Gate Driver
Parameter
Symbol
Values
Typ.
Unit
Note
Min.
Max.
High Level Output
Voltage
VOUTH1
VOUTH2
VOUTH3
VOUTH4
VCC2 -1.2
VCC2 -2.5
VCC2 -9
VCC2 -0.8
VCC2 -2.0
VCC2 -5
VCC2 -10
-2.0
–
–
–
–
–
V
V
V
V
A
IOUTH = -20 mA
IOUTH = -200 mA
IOUTH = -1 A
IOUTH = -2 A
High Level Output Peak IOUTH
Current
-1.5
IN+ = High,
IN- = Low;
OUT = High
Low Level Output
Voltage
VOUTL1
VOUTL2
VOUTL3
VOUTL4
–
VVEE2 +0.04 VVEE2+0.09
V
V
V
V
A
IOUTL = 20 mA
IOUTL = 200 mA
IOUTL = 1 A
–
VVEE2 +0.3
VVEE2 +2.1
VVEE2 +7
2.0
VVEE2+0.85
–
VVEE2+5
–
–
–
IOUTL = 2 A
Low Level Output Peak IOUTL
Current
1.5
IN+ = Low,
IN- = Low;
OUT = Low,
VVCC2 = 15 V,
VVEE2 = -8 V
5.4.4
Active Miller Clamp
Table 8
Active Miller Clamp
Symbol
Parameter
Values
Unit
Note
Min.
Typ.
Max.
Low Level Clamp
Voltage
VCLAMPL1
VCLAMPL2
VCLAMPL3
ICLAMPL
–
–
–
2
VVEE2+0.03 VVEE2 +0.08
V
V
V
A
IOUTL = 20 mA
IOUTL = 200 mA
VVEE2+0.3
VVEE2+1.9
–
VVEE2 +0.8
VVEE2 +4.8
–
IOUTL = 1 A
1)
Low Level Clamp
Current
Clamp Threshold
Voltage
VCLAMP
1.6
2.1
2.4
V
Related to VEE2
1) The parameter is not subject to production test - verified by design/characterization
Data Sheet
16
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5.4.5
Short Circuit Clamping
Short circuit clamping characteristics are measured with IN+ = High, IN- = Low and OUT = High.
Table 9
Short Circuit Clamping
Symbol
Parameter
Values
Typ.
Unit
Note
Min.
–
Max.
1.3
Clamping voltage (OUT) VCLPout
(VOUT - VVCC2
0.8
V
V
Ipulse test,
tCLPmax = 10 μs)
)
Clamping voltage
VCLPclamp
–
–
1.3
–
ICLAMP = 500 mA
(pulse test,
tCLPmax = 10 μs)
(CLAMP) (VVCLAMP-VVCC2
)
Clamping voltage
(CLAMP)
VCLPclamp
0.7
1.1
V
ICLAMP = 20 mA
5.4.6
Dynamic Characteristics
Dynamic characteristics are measured with VVCC1 = 5 V, VVCC2 = 15 V and VVEE2 = -8 V.
Table 10
Dynamic Characteristics
Symbol
Parameter
Values
Typ.
Unit
Note
Min.
145
Max.
195
Input IN+, IN- to output TPDON
propagation delay ON
170
165
-5
ns
ns
ns
CLOAD = 100 pF
VIN+ = 50%,
VOUT=50% @ 25°C
Input IN+, IN- to output TPDOFF
propagation delay OFF
145
-35
190
25
Input IN+, IN- to output TPDISTO
propagation delay
distortion (TPDOFF - TPDON
)
Input IN+, IN- to output TPDONt
propagation delay ON
variation due to temp
160
165
-25
190
195
5
220
225
35
ns
ns
ns
CLOAD = 100 pF
VIN+ = 50%,
VOUT = 50% @ 125°C
Input IN+, IN- to output TPDOFFt
propagation delay OFF
variation due to temp
Input IN+, IN- to output TPDISTOt
propagation delay
distortion (TPDOFF - TPDON
)
Data Sheet
17
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
Table 10
Dynamic Characteristics (cont’d)
Symbol
Parameter
Values
Typ.
Unit
ns
Note
Min.
135
Max.
195
Input IN+, IN- to output TPDONt
propagation delay ON
variation due to temp
165
155
-10
CLOAD = 100 pF
VIN+ = 50%,
VOUT = 50% @ -40°C
Input IN+, IN- to output TPDOFFt
propagation delay OFF
variation due to temp
125
-40
185
20
ns
ns
Input IN+, IN- to output TPDISTOt
propagation delay
distortion (TPDOFF - TPDON
)
Rise Time
TRISE
10
30
60
ns
ns
ns
ns
CLOAD = 1 nF
VL 10%, VH 90%
200
10
400
50
800
90
CLOAD = 34 nF
VL 10%, VH 90%
Fall Time
TFALL
CLOAD = 1 nF
VL 10%, VH 90%
200
350
600
CLOAD = 34 nF
VL 10%, VH 90%
5.4.7
Desaturation Protection
Table 11
Desaturation Protection
Parameter
Symbol
Min.
Values
Unit
Note
Typ.
500
Max.
550
Blanking Capacitor
Charge Current
IDESATC
450
μA
VVCC2 =15 V,
VVEE2=- 8 V
VDESAT = 2 V
Blanking Capacitor
Discharge Current
IDESATD
9
14
–
mA
VVCC2 =15 V,
VVEE2 = -8 V
VDESAT = 6 V
Desaturation
Reference Level
VDESAT
8.3
–
9
9.5
–
V
VVCC2 = 15 V
Desaturation Filter
Time
TDESATfilter
250
ns
VVCC2 = 15 V,
VVEE2 = -8 V
VDESAT = 9 V
Desaturation Sense to TDESATOUT
OUT Low Delay
–
–
350
–
430
ns
VOUT = 90%
CLOAD = 1 nF
Desaturation Sense to TDESATFLT
FLT Low Delay
2.25
μs
VFLT# = 10%;
IFLT # = 5 mA
Data Sheet
18
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
Table 11
Desaturation Protection (cont’d)
Parameter
Symbol
Values
Typ.
Unit
Note
Min.
0.4
Max.
0.95
Desaturation Low
Voltage
VDESATL
0.6
V
IN+ = Low, IN- = Low,
OUT = Low
Leading edge blanking TDESATleb
–
400
–
ns
Not subject of
production test
Data Sheet
19
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Electrical Parameters
5.4.8
Active Shut Down
Table 12
Active Shut Down
Symbol
Parameter
Values
Typ.
Unit
V
Note
Min.
–
Max.
2.0
1)
Active Shut Down Voltage VACTSD
–
IOUT = -200 mA,
VCC2 open
1) With reference to VEE2
Data Sheet
20
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Insulation Characteristics
6
Insulation Characteristics
Insulation characteristics are guaranteed only within the safety maximum ratings which must be ensured by
protective circuits in application. Surface mount classification is class A in accordance with CECCOO802.
This coupler is suitable for “basic insulation” only within the safety ratings. Compliance with the safety ratings
shall be ensured by means of suitable protective circuits.
6.1
Certified according to DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation
Table 13
According to DIN EN 60747-5-2
Description
Symbol
Characteristic
Unit
–
Installation classification per EN 60664-1, Table 1
for rated mains voltage ≤ 150 VRMS
for rated mains voltage ≤ 300 VRMS
I-IV
I-III
I-II
for rated mains voltage ≤ 600 VRMS
Climatic Classification
40/125/21
–
Pollution Degree (EN 60664-1)
Minimum External Clearance
Minimum External Creepage
2
–
CLR
8
mm
mm
–
CPG
CTI
8
Minimum Comparative Tracking Index
Maximum Repetitive Insulation Voltage
Highest Allowable Overvoltage
Maximum Surge Insulation Voltage
175
1420
6000
6000
VIORM
VIOTM
VIOSM
VPEAK
VPEAK
V
6.2
Recognized under UL 1577
Table 14
Recognized under UL 1577
Description
Symbol
VISO
Characteristic
3750
Unit
Vrms
Vrms
Insulation Withstand Voltage / 1 min
Insulation Test Voltage / 1 s
VISO
4500
6.3
Reliability
For Qualification Report please contact your local Infineon Technologies office.
Data Sheet
21
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Timing Diagramms
7
Timing Diagramms
50%
50%
IN+
90%
10%
OUT
TRISE
TFALL
TPDON
TPDOFF
Figure 5
Propagation Delay, Rise and Fall Time
IN+
IN-
/RST
OUT
Figure 6
Typical Switching Behavior
Data Sheet
22
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Timing Diagramms
IN+
TPDON
TPDON
TPDOFF
OUT
TDESATfilter
TDESATOUT
VDESAT typ. 9V
TDESATleb
TDESATleb
DESAT
blanking time
TDESATFLT
/FLT
/RST
>TRSTmin
Figure 7
DESAT Switch-Off Behavior
ESD diode conduction
IN+
VUVLOH1
VUVLOL1
VCC1
VUVLOH2
VUVLOL2
VCC2
OUT
RDY
/FLT
/RST
Figure 8
UVLO Behavior
Data Sheet
23
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Package Outlines
8
Package Outlines
Figure 9
PG-DSO-20 (Plastic (Green) Dual Small Outline Package)
Data Sheet
24
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Application Notes
9
Application Notes
9.1
Reference Layout for Thermal Data
The PCB layout shown in Figure 10 represents the reference layout used for the thermal characterisation. Pins
11, 12, 19 and 20 (GND1) and pins 1, 2, 9 and 10 (VEE2) require ground plane connections for achiving
maximum power dissipation. The 1ED020I12FA2 is conceived to dissipate most of the heat generated through
this pins.
Figure 10 Reference Layout for Thermal Data (Copper thickness 102 μm)
9.2
Printed Circuit Board Guidelines
Following factors should be taken into account for an optimum PCB layout.
•
•
Sufficient spacing should be kept between high voltage isolated side and low voltage side circuits.
The same minimum distance between two adjacent high-side isolated parts of the PCB should be
maintained to increase the effective isolation and reduce parasitic coupling.
•
•
In order to ensure low supply ripple and clean switching signals, bypass capacitor trace lengths should be
kept as short as possible.
Lowest trace length for VEE2 to GND2 decoupling could be achieved with capacitor closed to pins 2 and 4.
Data Sheet
25
Rev.3.0
2016-04-04
1ED020I12FA2
Single IGBT Driver IC
Revision History
Page or Item
Subjects (major changes since previous revision)
Rev. 3.0, 2016-04-04
All
Update latest template
Blockdiagram update
Figure 1
Table 2,Table 3, Removed Test Condition in table header
Table 4,Table 5,
Table 6,
Table 7,
Table 8,
Table 9,
Table 10,
Table 11,
Table 12
Table 5
Table 2
Changed VUVLOH1 into VUVLOL1
Symbol changed from Vmax2 to Vcc2 in Gate driver output
Data Sheet
26
Rev.3.0
2016-04-04
Please read the Important Notice and Warnings at the end of this document
Trademarks of Infineon Technologies AG
µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,
DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,
HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,
OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,
SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.
Trademarks updated November 2015
Other Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
IMPORTANT NOTICE
The information given in this document shall in no For further information on technology, delivery terms
Edition 2016-04-04
Published by
Infineon Technologies AG
81726 Munich, Germany
event be regarded as a guarantee of conditions or and conditions and prices, please contact the nearest
characteristics ("Beschaffenheitsgarantie").
Infineon Technologies Office (www.infineon.com).
WARNINGS
With respect to any examples, hints or any typical
values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities
of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer's compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer's products and any use of the product of
Infineon Technologies in customer's applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
© 2016 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Except as otherwise explicitly approved by Infineon
Technologies in
a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.
相关型号：
©2020 ICPDF网 联系我们和版权申明