5962-8874801TX [INFINEON]
Fixed Negative Standard Regulator, 15V, MSFM3, HERMETIC SEALED, METAL, TO-257AA, 3 PIN;型号: | 5962-8874801TX |
厂家: | Infineon |
描述: | Fixed Negative Standard Regulator, 15V, MSFM3, HERMETIC SEALED, METAL, TO-257AA, 3 PIN |
文件: | 总4页 (文件大小:29K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
OM1905STM OM1912STM OM1915STM
OM1905NTM OM1912NTM OM1915NTM
ISOLATED HERMETIC FIXED VOLTAGE NEGATIVE
REGULATORS APPROVED TO DESC DRAWINGS
Three Terminal, Fixed Voltage, 1.5 Amp
Precision Negative Regulators In Hermetic
JEDEC TO-257AA Package
FEATURES
• Isolated Hermetic Package, JEDEC TO-257AA Outline
• Output Voltages: -5V, -12V, -15V
• Output Voltages Set Internally to ±1%
• Built-In Thermal Overload Protection
• Short Circuit Current Limiting
• Product Is Also Available In Non-Isolated Package
• Similar To Industry Standards 7905, 7912, 7915
DESCRIPTION
These three terminal negative regulators are supplied in a hermetically sealed metall
package whose outline is similar to the industry standard TO-220 plastic package. All
protective features are designed into the circuit, including thermal shutdown, current limiting
and safe-area control. With heat sinking, they can deliver over 1.5 amps of output current.
These units feature internally trimmed output voltages to ±1% of nominal voltage.
Standard voltages are -5V, -12V, -15V. These units are ideally suited for Military
applications where a hermetically sealed package is required.
PART NUMBER DESIGNATOR
3.3
Standard Military Drawing Number
5962-8874601 UX
Omnirel Part Number
OM1905STM
OM1905NTM
OM1912STM
OM1912NTM
OM1915STM
OM1915NTM
5962-8874601 TX
5962-8874701 UX
5962-8874701 TX
5962-8874801 UX
5962-8874801 TX
“U” = Isolated
“T” = Non-Isolated
4 11 R2
Supersedes 1 07 R1
3.3 - 93
OM1905STM/NTM - OM1915STM/NTM
ABSOLUTE MAXIMUM RATINGS @ 25°C
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -35 V
Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .- 55°C to + 150°C
Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 150°C
Typical Power/Thermal Charateristics:
Rated Power @ 25° C TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15W
TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3W
Thermal Resistance
q
JC (Case U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2°C/W
qJC (Case T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5°C/W
qJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42°C/W
aa
ELECTRICAL CHARACTERISTICS -5 Volt VIN = -10V, Io = 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter
Symbol
Test Conditions
Min.
-4.95
-4.85
Max.
-5.05
-5.15
Unit
V
Output Voltage
VOUT
TA = 25°C
VIN = -7.5V to -20V
•
V
IO = 5mA to 1.0, A, P < 15W
Line Regulation
(Note 1)
VRLINE
VRLOAD
ISCD
VIN = -7.5V to -20V
12
25
5
mV
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
•
•
•
•
(Note 4)
VIN = -8.0V to -12V
12
20
25
15
30
2.5
3.0
0.4
Load Regulation
(Note 1)
IO = 5mA to 1.5 Amp
I
O = 250mA to 750 mA
Standby Current Drain
•
•
Standby Current Drain
Change With Line
Standby Current Drain
Change With Load
Dropout Voltage
DISCD
(Line)
DISCD
(Load)
VDO
VIN = -7.0V to -20V
IO = 5mA to 1000mA
•
•
0.4
mA
DVOUT = 100mV, IO = 1.0A
TA = 25°C
2.5
3.3
1.2
2.8
V
A
Peak Output Current
Short Circuit Current
(Note 2)
IO (pk)
IDS
1.5
VIN = -35V
A
•
•
A
Ripple Rejection
DVIN
DVOUT
NO
f =120 Hz, DVIN = -10V
(Note 3)
63
60
dB
dB
µV/V
RMS
mV
3.3
Output Noise Voltage
(Note 3)
TA = 25°C, f =10 Hz to 100KHz
40
75
Long Term Stability
(Note 3)
DVOUT
Dt
TA = 25°C, t = 1000 hrs.
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = -35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
3.3 - 94
OM1905STM/NTM - OM1915NTM/STM
ELECTRICAL CHARACTERISTICS -12 Volt VIN = -19V, Io = 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter
Symbol
Test Conditions
TA = 25°C
Min.
Max.
-12.12
-12.36
Unit
V
Output Voltage
VOUT
-11.88
-11.64
VIN = -14.5V to -27V
•
V
IO = 5mA to 1.0 A, P < 15W
Line Regulation
(Note 1)
VRLINE
VRLOAD
ISCD
VIN = -14.5V to -27V
20
50
10
30
32
60
16
30
3.5
4.0
0.8
mV
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
•
•
•
•
(Note 4)
VIN = -16V to -22V
Load Regulation
(Note 1)
IO = 5mA to 1.5 Amp
I
O = 250mA to 750 mA
Standby Current Drain
•
•
Standby Current Drain
Change With Line
Standby Current Drain
Change With Load
Dropout Voltage
DISCD
(Line)
DISCD
(Load)
VDO
VIN = -14.5V to -27V
IO = 5mA to 1000mA
•
•
0.5
mA
DVOUT = 100mV, IO = 1.0A
TA = 25°C, IO = 5mA to 1A
VIN = -35V
1.8
3.3
1.2
2.8
V
A
Peak Output Current
Short Circuit Current
(Note 2)
IO (pk)
IDS
1.5
A
•
•
A
Ripple Rejection
DVIN
DVOUT
NO
f =120 Hz, DVIN = -10V
(Note 3)
56
53
dB
dB
µV/V
RMS
mV
Output Noise Voltage
(Note 3)
TA = 25°C, f =10 Hz to 100KHz
40
Long Term Stability
(Note 3)
DVOUT
Dt
TA = 25°C, t = 1000 hrs.
120
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = -35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
4. Minimum load current for full line regulation = 5 mA.
MECHANICAL OUTLINE
CONNECTION DIAGRAM
.200
.190
.420
.410
3.3
.045
.035
4
.665
.645
.150
.140
.537
.527
.430
.410
.038 MAX.
.005
Case U
1 Ground
2 Input
Case T
1 Ground
2 Input
.750
.500
3 Output
4 No Connection
3 Output
4 Input
1
2
3
.120 TYP.
.100 TYP.
.035
.025
3.3 - 95
OM1905STM/NTM - OM1915STM/NTM
ELECTRICAL CHARACTERISTICS -15 Volt VIN = -23V, Io = 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter
Symbol
Test Conditions
TA = 25°C
Min.
Max.
-15.15
-15.45
Unit
V
Output Voltage
VOUT
-14.85
-14.55
VIN = -17.5V to -30V
•
V
IO = 5mA to 1.0 A, P < 15 W
Line Regulation
(Note 1)
VRLINE
VRLOAD
ISCD
VIN = -17.5V to -30V
25
50
15
25
35
75
21
45
6.0
6.5
0.8
mV
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
•
•
•
•
(Note 4)
VIN = -20V to -26V
Load Regulation
(Note 1)
IO = 5mA to 1.5 Amp
I
O = 250mA to 750 mA
Standby Current Drain
•
•
Standby Current Drain
Change With Line
Standby Current Drain
Change With Load
Dropout Voltage
DISCD
(Line)
DISCD
(Load)
VDO
VIN = -17.5V to -30V
IO = 5mA to 1000 mA
•
•
0.5
mA
DVOUT = 100mV, IO = 1.0A
TA = 25°C
2.5
3.3
1.2
2.8
V
A
Peak Output Current
Short Circuit Current
(Note 2)
IO (pk)
IDS
1.5
VIN = -35V
A
•
•
A
Ripple Rejection
DVIN
DVOUT
NO
f =120 Hz, DVIN = -10V
(Note 3)
53
50
dB
dB
µV/V
RMS
mV
Output Noise Voltage
(Note 3)
TA = 25°C, f =10 Hz to 100KHz
40
Long Term Stability
(Note 3)
DVOUT
Dt
TA = 25°C, t = 1000 hrs.
150
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = -35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
TYPICAL PERFORMANCE CHARACTERISTICS
PEAK OUTPUT
RIPPLE REJECTION
DROPOUT VOLTAGE
3.3
2.5
2
100
80
3.5
3
Tj = -55°C
VOUT = 5V
IOUT = 1A
2.5
1.5
1
60
40
20
0
2
IOUT = 500mA
Tj = 25°C
1.5
IOUT = 0A
VIN - V = 8VDC +3.5Vrms
IOUT = 1A
1
0.5
0
0.5
Tj = 150°C
Tj = 25°C
DVOUT = 100MV
DVOUT = 100mV
0
-75-50 -25
0
25 50 75 100 125 150
0
5
10 15 20
25
30 35
10
100
1k
10k
100k
Frequency (Hz)
Input To Output Differential (V)
Junction Temperature (°C)
205 Crawford Street, Leominster, MA 01453 USA (508) 534-5776 FAX (508) 537-4246
相关型号:
©2020 ICPDF网 联系我们和版权申明