5962-9204001HXA [INFINEON]
DC-DC Regulated Power Supply Module, 2 Output, 15W, Hybrid,;
| 型号： | 5962-9204001HXA |
| 厂家： | 
Infineon |
| 描述： | DC-DC Regulated Power Supply Module, 2 Output, 15W, Hybrid, |
| 文件： | 总13页 (文件大小：83K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
02-02-20
APPROVED
Raymond Monnin
Robert M. Heber
Charles F. Saffle
Updated drawing to the current requirement of MIL-PRF-38534. - gjc
Updated drawing per 5 year review. - sld
A
B
C
08-07-07
Table II, add note to Group C end-point test parameters. Update
boilerplate paragraphs. -gz
10-02-02
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
REV
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
C
C
SHEET
10
11
12
PMIC N/A
PREPARED BY
Gary Zahn
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Michael A. Frye
APPROVED BY
D. M. Cool
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
MICROCIRCUIT, HYBRID, LINEAR, 12-VOLT,
DUAL CHANNEL, DC/DC CONVERTER
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
92-02-04
AMSC N/A
REVISION LEVEL
SIZE
A
CAGE CODE
5962-92040
67268
C
SHEET
1 OF 12
DSCC FORM 2233
APR 97
5962-E182-10
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
-
92040
01
H
X
X
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
Circuit function
01
02
03
AHE2812D/CH
AHE2812D/CH - SLV
AHE2812D/CH - MSTR
DC/DC converter, 15 W, 12 V dual output
DC/DC converter, 15 W, 12 V dual output
DC/DC converter, 15 W, 12 V dual output
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
H
G
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
E
D
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
2
DSCC FORM 2234
APR 97
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
X
Z
See figure 1
See figure 1
10
10
Dual-in-line package
Flanged package
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage ..............................................................................
Power dissipation.......................................................................
Lead temperature (soldering, 10 seconds) ................................
Storage temperature..................................................................
-0.5 V dc to +50 V dc
6 W
+300C
-65C to +135C
1.4 Recommended operating conditions.
Input voltage range....................................................................
Output power 2/ 3/ .....................................................................
Case operating temperature range (TC).....................................
+17 V dc to +40 V dc
15 W
-55C to +125C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
_________
1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Derate output power linearly above case temperature +125C to 0 at +135C.
3/ At least 25 percent of the total power should be from the positive output.
SIZE
STANDARD
5962-92040
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.5 Block diagram. The block diagram shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
SIZE
STANDARD
5962-92040
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
Group A
subgroups
Device
types
Limits
Unit
-55C T +125C
C
VIN = 28 V dc 5%, CL = 0
unless otherwise specified
Min
Max
Output voltage 1/
VOUT
IOUT = 0
1
All
V
11.88
11.76
0.0
12.12
2,3
12.24
625
60
Output current 1/ 2/
IOUT
VRIP
VIN = 17, 28 and 40 V dc
mA
1,2,3
1,2,3
All
All
Output ripple voltage 1/ 3/
VIN = 17, 28, and 40 V dc
B.W. = dc to 2 MHz
mV p-p
Output power 1/ 2/ 4/
Line regulation 1/ 5/
POUT
VIN = 17, 28, and 40 V dc
1,2,3
1
All
All
15
W
VRLINE
VIN = 17, 28, and 40 V dc
30
60
mV
IOUT = 0, 313, and 625 mA
2,3
Load regulation 1/
Input current
VRLOAD
VIN = 17, 28, and 40 V dc
1,2,3
All
All
120
mV
mA
IOUT = 0, 313 and 625 mA
IIN
IOUT = 0, inhibit (pin 2)
1,2,3
18
40
50
tied to input return (pin 10)
IOUT = 0,
inhibit (pin 2) = open
IOUT = 625 mA
Input ripple current 3/
Efficiency
IRIP
1,2,3
1
All
All
mA p-p
%
B.W. = dc to 2 MHz
EFF
80
I
OUT = 625 mA,
TC = +25C
Isolation
ISO
Input to output or any pin
to case (except pin 8) at 500
V dc, TC = +25C
1
All
100
M
Capacitive load 6/ 7/
CL
PD
No effect on dc performance,
4
1
All
All
200
F
TC = +25C
Power dissipation load
fault
6
6
W
Overload, TC = +25C 8/
Short circuit, TC = +25C
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics. - Continued.
Test
Symbol
Conditions
Group A
subgroups
Device
types
Limits
Unit
-55C T +125C
C
VIN = 28 V dc 5%, CL = 0
unless otherwise specified
Min
225
Max
275
Switching frequency 1/
FS
4,5,6
01
02
03
All
kHz
IOUT = 625 mA
225
250
245
275
+300
+450
+500
+750
70
Output response to step
transient load changes
9/
VOTLOAD
50 percent load to/form 100
percent load
4
-300
-450
-500
-750
mV pk
5,6
No load to/from 50 percent
load
4
All
All
5,6
Recovery time step
transient load changes
9/ 10/
TTLOAD
50 percent load to/from 100
percent load
4
s
5,6
100
1500
5
No load to 50 percent load
50 percent load to no load
Input step 17 to 40 V dc
Input step 40 to 17 V dc
Input step 17 to 40 V dc
4,5,6
4,5,6
4,5,6
4,5,6
4,5,6
All
All
All
All
All
ms
Output response to
transient step line
changes 7/ 11/
VOTLINE
1200
-1500
4
mV pk
Recovery time transient
step line changes
7/ 10/ 11/
TTLINE
ms
Input step 40 to 17 V dc
4,5,6
All
4
Turn on overshoot 1/
Turn on delay 1/ 12/
Load fault recovery 7/
VTonOS
TonD
4,5,6
4,5,6
4,5,6
All
All
All
600
10
mV pk
ms
I
OUT = 0 and 625 mA
IOUT = 0 and 625 mA
TrLF
10
ms
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.- Continued.
1/ Tested at each output.
2/ Parameter guaranteed by line and load regulation tests.
3/ Bandwidth guaranteed by design. Tested for 20 kHz to 2 MHz.
4/ Total power at both outputs. For operation at 16 V dc input, derate output power by 33 percent.
5/ When operating with unbalanced loads, at least 25 percent of the load must be on the positive output to maintain regulation.
6/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in
excess of the maximum limit will not disturb loop stability but may interfere with the operation of the load fault detection
circuitry, appearing as a short circuit during turn on.
7/ Parameter shall be tested as part of design characterization and after design or process changes. Thereafter parameters
shall be guaranteed to the limits specified in table I.
8/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit
protection and is the condition of maximum power dissipation.
9/ Load step transition time between 2 and 10 microseconds.
10/ Recovery time is measured from the initiation of the transient to where VOUT has returned to within 1 percent of VOUT at 50
percent load.
11/ Input step transition time between 2 and 10 microseconds.
12/ Turn on delay time measurement is for either a step application of power at the input or the removal of a ground signal from
the inhibit pin (pin 2) while power is applied to the input.
SIZE
STANDARD
5962-92040
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
7
DSCC FORM 2234
APR 97
Case outline X.
Inches
mm
.040
.260
1.02
6.60
.400
.495
.800
1.120
2.120
10.16
12.57
20.32
28.45
53.85
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are for general information only.
3. Unless otherwise specified, tolerance is ±.005 Inches (0.13 mm).
4. Case outline X weight: 55 grams maximum.
FIGURE 1. Case outlines.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
8
DSCC FORM 2234
APR 97
Case outline Z.
Inches
mm
.010
.040
0.25
1.02
.048
1.22
.060
1.52
.162
4.11
.260
6.60
.400
.495
.800
1.120
2.120
2.550
2.880
10.16
12.57
20.32
28.45
53.85
64.77
73.15
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are for general information only.
3. Unless otherwise specified, tolerance is ±.005 Inches (0.13 mm).
4. Case outline Z weight: 58 grams maximum.
FIGURE 1. Case outlines - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
9
DSCC FORM 2234
APR 97
Device types
Case outlines
01
02 and 03
X and Z
X and Z
Terminal number Terminal symbol
Terminal symbol
Input
1
2
Input
Inhibit in
Inhibit in
3
Positive output
Output return
Negative output
No connection
No connection
Case ground
No connection
Input return
Positive output
Output return
Negative output
No connection
No connection
Case ground
Sync in/out
4
5
6
7
8
9
10
Input return
FIGURE 2. Terminal connections.
FIGURE 3. Block diagram.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-92040
A
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
10
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
Final electrical parameters
Group A test requirements
1*, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6
1, 2, 3, 4
Group C end-point electrical
parameters 1/
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
Not applicable
* PDA applies to subgroup 1.
1/ As a minimum, for all Group C testing performed after February 2, 2010
manufacturers shall perform subgroups 1, 2, and 3 from the Group A
electrical test table (Table C-Xa of MIL-PRF-38534).
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified
in method 1015 of MIL-STD-883.
(2)
T as specified in accordance with table I of method 1015 of MIL-STD-883.
C
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
SIZE
STANDARD
5962-92040
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
11
DSCC FORM 2234
APR 97
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified
in method 1005 of MIL-STD-883.
(2)
T as specified in accordance with table I of method 1005 of MIL-STD-883.
C
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-
38534.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be
used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC
5962) should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614)
692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing.
SIZE
STANDARD
5962-92040
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
12
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 10-02-02
Approved sources of supply for SMD 5962-92040 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded
by the next dated revisions of MIL-HDBK-103 and QML-38534. DSCC maintains an online database of all current
sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9204001HXA
5962-9204001HZA
5962-9204002HXA
5962-9204002HZA
5962-9204003HXA
5962-9204003HZA
52467
52467
52467
52467
52467
52467
AHE2812D/CH
AHE2812DF/CH
AHE2812D/CH-SLV
AHE2812DF/CH-SLV
AHE2812D/CH-MSTR
AHE2812DF/CH-MSTR
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the Vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
52467
International Rectifier, HiRel Products, Incorporated
2270 Martin Ave
Santa Clara CA 95050
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
©2020 ICPDF网 联系我们和版权申明