AFL5015SWES [INFINEON]
HYBRID-HIGH RELIABILITY DC/DC CONVERTER;型号: | AFL5015SWES |
厂家: | Infineon |
描述: | HYBRID-HIGH RELIABILITY DC/DC CONVERTER |
文件: | 总12页 (文件大小:210K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD - 94457B
AFL50XXS SERIES
50V Input, Single Output
HYBRID-HIGH RELIABILITY
DC/DC CONVERTER
Description
The AFL Series of DC/DC converters feature high power
density with no derating over the full military temperature
range. This series is offered as part of a complete family
of converters providing single and dual output voltages
and operating from nominal +28V, +50V, +120V or +270V
inputs with output power ranging from 80W to 120W.
For applications requiring higher output power,
individual converters can be operated in parallel. The
internal current sharing circuits assure equal current
distribution among the paralleled converters. This series
incorporates International Rectifier’s proprietary
magnetic pulse feedback technology providing
optimum dynamic line and load regulation response.
This feedback system samples the output voltage at
the pulse width modulator fixed clock frequency,
nominally 550KHz. Multiple converters can be
synchronized to a system clock in the 500KHz to 700
KHz range or to the synchronization output of one
converter. Undervoltage lockout, primary and secondary
referenced inhibit, soft-start and load fault protection
are provided on all models.
AFL
Features
n 30V To 80V Input Range
n
5V, 8V, 9V, 12V, 15V and 28V Outputs Available
3
n High Power Density - up to 84 W/in
n Up To 120W Output Power
n Parallel Operation with Stress and Current
Sharing
n Low Profile (0.380") Seam Welded Package
n Ceramic Feedthru Copper Core Pins
n High Efficiency - to 85%
n Full Military Temperature Range
n Continuous Short Circuit and Overload
Protection
n Remote Sensing Terminals
n Primary and Secondary Referenced
Inhibit Functions
n Line Rejection > 40dB - DC to 50KHz
n External Synchronization Port
n Fault Tolerant Design
n Dual Output Versions Available
n Standard Microcircuit Drawings Available
These converters are hermetically packaged in two
enclosure variations, utilizing copper core pins to
minimize resistive DC losses. Three lead styles are
available, each fabricated with International Rectifier’s
rugged ceramic lead-to-package seal assuring long
term hermeticity in the most harsh environments.
Manufactured in a facility fully qualified to MIL-PRF-
38534, these converters are fabricated utilizing DSCC
qualified processes. For available screening options,
refer to device screening table in the data sheet.
Variations in electrical, mechanical and screening can
be accommodated. Contact IR Santa Clara for special
requirements.
www.irf.com
1
12/15/06
AFL50XXS Series
Specifications
Absolute Maximum Ratings
Input voltage
-0.5V to +100VDC
300°C for 10 seconds
-55°C to +125°C
Soldering temperature
Operating case temperature
Storage case temperature
-65°C to +135°C
Static Characteristics -55°C < TCASE < +125°C, 30V< VIN < 80V unless otherwise specified.
Group A
Parameter
INPUT VOLTAGE
Subgroups
Test Conditions
Min
Nom
Max
Unit
Note 6
30
50
80
V
V
= 50 Volts, 100% Load
OUTPUT VOLTAGE
IN
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
1
1
1
1
1
1
4.95
7.92
8.91
11.88
14.85
27.72
5.00
8.00
9.00
12.00
15.00
28.00
5.05
8.08
9.09
12.12
15.15
28.28
V
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
4.90
7.84
8.82
11.76
14.70
27.44
5.10
8.16
9.18
12.24
15.30
28.56
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
V
= 30, 50, 80 Volts - Note 6
OUTPUT CURRENT
IN
16.0
10.0
10.0
9.0
8.0
4.0
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
A
Note 6
OUTPUT POWER
80
80
90
108
120
112
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
W
Note 1
= 50 Volts, 100% Load - Note 1, 6
10,000
-0.015
µF
MAXIMUM CAPACITIVE LOAD
V
+0.015
%/°C
OUTPUT VOLTAGE
TEMPERATURE COEFFICIENT
IN
OUTPUT VOLTAGE REGULATION
1, 2, 3
1, 2, 3
No Load, 50% Load, 100% Load
-70.0
-20.0
+70.0
+20.0
mV
mV
AFL5028S
All Others
Line
Line
V
= 30, 50, 80 Volts
IN
Load
1, 2, 3
-1.0
+1.0
%
V
= 30, 50, 80 Volts, 100% Load,
OUTPUT RIPPLE VOLTAGE
AFL5005S
IN
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
30
40
BW = 10MHz
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
40
mV
pp
45
50
100
For Notes to Specifications, refer to page 4
2
www.irf.com
AFL50XXS Series
Static Characteristics (Continued)
Group A
Parameter
INPUT CURRENT
Subgroups
Test Conditions
= 50 Volts
Min
Nom
Max
Unit
V
IN
1
2, 3
50
60
No Load
I
= 0
OUT
mA
1, 2, 3
1, 2, 3
5.0
5.0
Inhibit 1
Inhibit 2
Pin 4 Shorted to Pin 2
Pin 12 Shorted to Pin 8
V
= 50 Volts, 100% Load, BW = 10MHz
INPUT RIPPLE CURRENT
AFL5005S
IN
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
60
60
60
60
60
60
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
mA
pp
V
= 90% V
, V = 50 Volts
NOM IN
CURRENT LIMIT POINT
As a percentage of full rated load
OUT
Note 5
1
2
3
115
105
125
125
115
140
%
W
V
V
IN = 50 Volts
LOAD FAULT POWER DISSIPATION
1, 2, 3
32
Overload or Short Circuit
IN = 50 Volts, 100% Load
EFFICIENCY
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
78
79
80
81
82
82
81
82
83
84
85
84
%
V
µ
A
V
µA
ENABLE INPUTS (Inhibit Function)
Converter Off
1, 2, 3
1, 2, 3
Logical Low on Pin 4 or Pin 12
Note 1
Logical High on Pin 4 and Pin 12 - Note 9
Note 1
-0.5
2.0
0.8
100
50
Sink Current
Converter On
Sink Current
100
1, 2, 3
500
550
600
KHz
SWITCHING FREQUENCY
SYNCHRONIZATION INPUT
Frequency Range
1, 2, 3
1, 2, 3
1, 2, 3
500
2.0
-0.5
700
10
0.8
100
80
KHz
V
V
ns
%
Pulse Amplitude, Hi
Pulse Amplitude, Lo
Pulse Rise Time
Note 1
Note 1
20
Pulse Duty Cycle
Ω
M
1
Input to Output or Any Pin to Case
(except Pin 3). Test @ 500VDC
100
ISOLATION
Slight Variations with Case Style
85
g
DEVICE WEIGHT
MTBF
MIL-HDBK-217F, AIF @ T = 40°C
C
300
KHrs
For Notes to Specifications, refer to page 4
www.irf.com
3
AFL50XXS Series
Dynamic Characteristics -55°C < TCASE < +125°C, VIN=50V unless otherwise specified.
Group A
Parameter
Subgroups
Test Conditions
Min
Nom
Max
Unit
Note 2, 8
LOAD TRANSIENT RESPONSE
⇔
4, 5, 6
4, 5, 6
Load Step 50%
100%
-450
-450
-500
-500
-600
-600
-750
-750
-750
-750
-1200
-1200
450
200
mV
µs
AFL5005S
AFL5008S
AFL5009S
AFL5012S
AFL5015S
AFL5028S
Amplitude
Recovery
4, 5, 6
4, 5, 6
Load Step 10% ⇔ 50%
Load Step 50% ⇔ 100%
Load Step 10% ⇔ 50%
Load Step 50% ⇔ 100%
Load Step 10% ⇔ 50%
Load Step 50% ⇔ 100%
Load Step 10% ⇔ 50%
Load Step 50% ⇔ 100%
Load Step 10% ⇔ 50%
Load Step 50% ⇔ 100%
Load Step 10% ⇔ 50%
450
300
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
500
200
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
500
300
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
600
200
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
600
300
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
750
200
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
750
300
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
750
200
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
750
300
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
1200
200
mV
µs
Amplitude
Recovery
4, 5, 6
4, 5, 6
1200
300
mV
µs
Amplitude
Recovery
Note 1, 2, 3
LINE TRANSIENT RESPONSE
-500
500
500
mV
µs
Amplitude
Recovery
⇔
80 Volts
V
Step = 30
IN
TURN-ON CHARACTERISTICS
V
= 30, 50, 80 Volts. Note 4
IN
Overshoot
Delay
4, 5, 6
4, 5, 6
Enable 1, 2 on. (Pins 4, 12 high or
open)
250
120
mV
ms
50
40
75
50
Same as Turn On Characteristics.
LOAD FAULT RECOVERY
LINE REJECTION
MIL-STD-461D, CS101, 30Hz to 50KHz
Note 1
dB
Notes to Specifications:
1.
2.
Parameters not 100% tested but are guaranteed to the limits specified in the table.
Recovery time is measured from the initiation of the transient to where V has returned to within ±1.0% of
OUT
Line transient transition time ≥ 100µs.
Turn-on delay is measured with an input voltage rise time of between 100V and 500V per millisecond.
Current limit point is that condition of excess load causing output voltage to drop to 90% of nominal.
Parameter verified as part of another test.
All electrical tests are performed with the remote sense leads connected to the output leads at the load.
Load transient transition time ≥ 10µs.
OUT
V
at 50% load.
3.
4.
5.
6.
7.
8.
9.
Enable inputs internally pulled high. Nominal open circuit voltage ≈ 4.0VDC.
4
www.irf.com
AFL50XXS Series
Block Diagram
Figure I. AFL Single Output
Input
Filter
1
4
5
+ Input
Output
Filter
+Output
+Sense
7
Primary
Bias Supply
Enable 1
10
Current
Sense
Sync Output
Share
Amplifier
11 Share
Control
Error
Amp
& Ref
Sync Input
Case
6
3
Enable 2
FB
12
Sense
Amplifier
9
8
Return Sense
Output Return
Input Return
2
of application. When the remote sensing feature is not used,
the sense lead should be connected to their respective
output terminals at the converter. Figure III. illustrates a
typical remotely sensed application.
Circuit Operation and Application Information
The AFL series of converters employ a forward switched
mode converter topology. (refer to Figure I.) Operation of
the device is initiated when a DC voltage whose magnitude
is within the specified input limits is applied between pins 1
and 2. If pin 4 is enabled (at a logical 1 or open) the primary
bias supply will begin generating a regulated housekeeping
voltage bringing the circuitry on the primary side of the
converter to life. A power MOSFET is used to chop the DC
input voltage into a high frequency square wave, applying
this chopped voltage to the power transformer at the nominal
converter switching frequency. Maintaining a DC voltage
within the specified operating range at the input assures
continuous generation of the primary bias voltage.
Inhibiting Converter Output (Enable)
As an alternative to application and removal of the DC voltage
to the input, the user can control the converter output by
providing TTL compatible, positive logic signals to either of
two enable pins (pin 4 or 12). The distinction between these
two signal ports is that enable 1 (pin 4) is referenced to the
input return (pin 2) while enable 2 (pin 12) is referenced to
the output return (pin 8). Thus, the user has access to an
inhibit function on either side of the isolation barrier. Each
port is internally pulled “high” so that when not used, an
open connection on both enable pins permits normal
converter operation. When their use is desired, a logical
“low” on either port will shut the converter down.
The switched voltage impressed on the secondary output
transformer winding is rectified and filtered to generate the
converter DC output voltage. An error amplifier on the
secondary side compares the output voltage to a precision
reference and generates an error signal proportional to the
difference. This error signal is magnetically coupled through
the feedback transformer into the controller section of the
converter varying the pulse width of the square wave signal
driving the MOSFET, narrowing the width if the output voltage
is too high and widening it if it is too low, thereby regulating
the output voltage.
Figure II. Enable Input Equivalent Circuit
+5.6 V
100K
1N4148
Pin 4 or
Pin 12
290K
180K
Disable
Remote Sensing
2N3904
Connection of the + and - sense leads at a remotely located
load permits compensation for excessive resistance
between the converter output and the load when their
physical separation could cause undesirable voltage drop.
This connection allows regulation to the placard voltage at
Pin 2 or
Pin 8
www.irf.com
5
AFL50XXS Series
Internally, these ports differ slightly in their function. In use,
a low on Enable 1 completely shuts down all circuits in the
converter, while a low on Enable 2 shuts down the secondary
side while altering the controller duty cycle to near zero.
Externally, the use of either port is transparent to the user
save for minor differences in idle current. (See specification table).
high level of +2.0V. The sync output of another converter
which has been designated as the master oscillator provides
a convenient frequency source for this mode of operation.
When external synchronization is not required, the sync in
pin should be left open (unconnected )thereby permitting
the converter to operate at its’ own internally set frequency.
The sync output signal is a continuous pulse train set at
550 ± 50KHz, with a duty cycle of 15 ± 5.0%. This signal is
referenced to the input return and has been tailored to be
compatible with the AFL sync input port. Transition times
are less than 100ns and the low level output impedance is
less than 50Ω. This signal is active when the DC input
voltage is within the specified operating range and the
converter is not inhibited. This output has adequate drive
reserve to synchronize at least five additional converters.
A typical connection is illustrated in Figure III.
Synchronization of Multiple Converters
When operating multiple converters, system requirements
often dictate operation of the converters at a common
frequency. To accommodate this requirement, the AFL
series converters provide both a synchronization input
and output.
The sync input port permits synchronization of an AFL
converter to any compatible external frequency source
oper- ating between 500KHz and 700KHz. This input signal
should be referenced to the input return and have a 10%
to 90% duty cycle. Compatibility requires transition times
less than 100ns, maximum low level of +0.8V and a minimum
Figure III. Preferred Connection for Parallel Operation
1
12
Power
Input
Enable 2
Vin
Rtn
Share
+ Sense
- Sense
Return
Case
AFL
AFL
Enable 1
Sync Out
Sync In
+ Vout
7
6
1
Optional
Synchronization
Connection
Share Bus
12
Enable 2
Vin
Rtn
Share
+ Sense
- Sense
Case
Enable 1
Sync Out
Sync In
Return
to Load
+ Vout
7
6
1
12
Enable 2
Vin
Rtn
Share
+ Sense
- Sense
Return
Case
AFL
Enable 1
Sync Out
Sync In
+ Vout
7
6
(Other Converters)
AFL series operating in the parallel mode is that in addition
to sharing the current, the stress induced by temperature
will also be shared. Thus if one member of a paralleled set
is operating at a higher case temperature, the current it
provides to the load will be reduced as compensation for
Parallel Operation-Current and Stress Sharing
Figure III. illustrates the preferred connection scheme for
operation of a set of AFL converters with outputs operating
in parallel. Use of this connection permits equal sharing
among the members of a set whose load current exceeds
the capacity of an individual AFL. An important feaure of the
the temperature induced stress on that device.
6
www.irf.com
AFL50XXS Series
A conservative aid to estimating the total heat sink surface
When operating in the shared mode, it is important that
symmetry of connection be maintained as an assurance of area (AHEAT SINK) required to set the maximum case temp-
optimum load sharing performance. Thus, converter outputs erature rise (∆T) above ambient temperature is given by
the following expression:
should be connected to the load with equal lengths of wire of
the same gauge and sense leads from each converter should
be connected to a common physical point, preferably at the
load along with the converter output and return leads. All
converters in a paralleled set must have their share pins
connected together. This arrangement is diagrammatically
illustrated in Figure III. showing the outputs and return pins
connected at a star point which is located close as possible to
the load.
−1.43
⎧
⎫
⎬
⎭
∆T
0.85
⎨
⎩
A
HEAT SINK
≈
− 3.0
80P
where
∆T = Case temperature rise above ambient
⎧
⎨
⎩
⎫
⎭
1
As a consequence of the topology utilized in the current
sharing circuit, the share pin may be used for other functions.
In applications requiring only a single converter, the voltage
appearing on the share pin may be used as a “current
monitor”. The share pin open circuit voltage is nominally
+1.00V at no load and increases linearly with increasing
output current to +2.20V at full load.
⎬
−1
P = Device dissipation in Watts = POUT
Eff
As an example, it is desired to maintain the case temperature
of an AFL5015S at ≤ +85°C while operating in an open area
whose ambient temperature is held at a constant +25°C;
then
Thermal Considerations
∆T = 85 - 25 = 60°C
Because of the incorporation of many innovative
technological concepts, the AFL series of converters is
capable of providing very high output power from a package
of very small volume. These magnitudes of power density
can only be obtained by combining high circuit efficiency
with effective methods of heat removal from the die junctions.
This requirement has been effectively addressed inside the
device; but when operating at maximum loads, a significant
amount of heat will be generated and this heat must be
conducted away from the case. To maintain the case
temperature at or below the specified maximum of 125°C,
this heat must be transferred by conduction to an
appropriate heat dissipater held in intimate contact with the
converter base-plate.
If the worst case full load efficiency for this device is 83%;
then the power dissipation at full load is given by
⎧
⎨
⎫
⎭
1
⎬ ( )
−1 = 120• 0.205 = 24.6W
P = 120•
⎩.83
and the required heat sink area is
−1.43
⎧
⎨
⎩
⎫
⎬
⎭
60
A
HEAT SINK
=
− 3.0 = 71in2
0.85
80 • 24.6
Since the effectiveness of this heat transfer is dependent
on the intimacy of the baseplate/heatsink interface, it is
strongly recommended that a high thermal conductivity heat
transferring medium is inserted between the baseplate and
heatsink. The material most frequently utilized at the factory
during all testing and burn-in processes is sold under the
Thus, a total heat sink surface area (including fins, if any) of
2
71 in in this example, would limit case rise to 60°C above
ambient. A flat aluminum plate, 0.25" thick and of
2
approximate dimension 4" by 9" (36 in per side) would
suffice for this application in a still air environment. Note
that to meet the criteria in this example, both sides of the
plate require unrestricted exposure to the ambient air.
1
trade name of Sil-Pad® 400 . This particular product is an
insulator but electrically conductive versions are also
available. Use of these materials assures maximum surface
contact with the heat dissipater thereby compensating for
any minor surface variations. While other available types of
heat conductive materials and thermal compounds provide
similar effectiveness, these alternatives are often less
convenient and can be somewhat messy to use.
1
Sil-Pad is a registered Trade Mark of Bergquist, Minneapolis, MN
www.irf.com
7
AFL50XXS Series
Input Filter
The AFL50XXS series converters incorporate a LC input
filter whose elements dominate the input load impedance
characteristic at turn-on. The input circuit is as shown in
Figure IV.
Finding a resistor value for a particular output voltage, is
simply a matter of substituting the desired output voltage
and the nominal device voltage into the equation and solving
for the corresponding resistor value.
Figure V. Connection for VOUT Adjustment
Figure IV. Input Filter Circuit
Enable 2
0.75µH
Share
RADJ
Pin 1
+ Sense
AFL50xxS
- Sense
2.7µfd
Return
To Load
+ V
out
Pin 2
Note: Radj must be set ≥ 500Ω
Undervoltage Lockout
Attempts to adjust the output voltage to a value greater than
120% of nominal should be avoided because of the potential
of exceeding internal component stress ratings and
subsequent operation to failure. Under no circumstance
should the external setting resistor be made less than 500W.
By remaining within this specified range of values, completely
safe operation fully within normal component derating limits
is assured.
A minimum voltage is required at the input of the converter
to initiate operation. This voltage is set to 26.5 ± 1.5V. To
preclude the possibility of noise or other variations at the
input falsely initiating and halting converter operation, a
hysteresis of approximately 2.0V is incorporated in this
circuit. Thus if the input voltage droops to 24.5 ± 1.5V, the
converter will shut down and remain inoperative until the
input voltage returns to ≈ 25V.
Examination of the equation relating output voltage and
resistor value reveals a special benefit of the circuit topology
utilized for remote sensing of output voltage in the AFL50XXS
series of converters. It is apparent that as the resistance
increases, the output voltage approaches the nominal set
value of the device. In fact the calculated limiting value of
output voltage as the adjusting resistor becomes very large
Output VoltageAdjust
In addition to permitting close voltage regulation of remotely
located loads, it is possible to utilize the converter sense
pins to incrementally increase the output voltage over a
limited range. The adjustments made possible by this method
are intended as a means to “trim” the output to a voltage
setting for some particular application, but are not intended
to create an adjustable output converter. These output
voltage setting variations are obtained by connecting an
appropriate resistor value between the +sense and -sense
pins while connecting the -sense pin to the output return pin
as shown in Figure V. below. The range of adjustment and
corresponding range of resistance values can be determined
is ≈ 25mV above nominal device voltage.
The consequence is that if the +sense connection is
unintentionally broken, an AFL50XXS has a fail-safe output
voltage of Vout + 25mV, where the 25mV is independent of
the nominal output voltage. It can be further demonstrated
that in the event of both the + and - sense connections
being broken, the output will be limited to Vout + 440mV.
This 440mV is also essentially constant independent of the
by use of the following equation.
nominal output voltage.
⎧
⎨
⎩
⎫
⎬
⎭
VNOM
Radj = 100•
VOUT - VNOM -.025
Where
VNOM = device nominal output voltage, and
VOUT = desired output voltage
8
www.irf.com
AFL50XXS Series
Table 1. Nominal Resistance of Cu Wire
General Application Information
The AFL50XXS series of converters are capable of
providing large transient currents to user loads on demand.
Because the nominal input voltage range in this series is
relatively low, the resulting input current demands will be
correspondingly large. It is important therefore, that the line
impedance be kept very low to prevent steady state and
transient input currents from degrading the supply voltage
between the voltage source and the converter input. In
applications requiring high static currents and large
transients, it is recommended that the input leads be made
of adequate size to minimize resistive losses, and that a
good quality capacitor of approximately 100µF be connected
directly across the input terminals to assure an adequately
low impedance at the input terminals. Table I relates nominal
resistance values and selected wire sizes.
Wire Size, AWG
Resistance per ft
24 Ga
22 Ga
20 Ga
18 Ga
16 Ga
14 Ga
12 Ga
25.7 mΩ
16.2 mΩ
10.1 m
Ω
6.4 mΩ
4.0 mΩ
2.5 m
Ω
1.6 mΩ
Incorporation of a 100µF capacitor at the input terminals is
recommended as compensation for the dynamic effects
of the parasitic resistance of the input cable reacting with
the complex impedance of the converter input, and to
provide an energy reservoir for transient input current
requirements.
Figure VI. Problems of Parasitic Resistance in input Leads
(See text)
Rp
Rp
Iin
Vin
100
µfd
esource
Rtn
eRtn
IRtn
Case
Enable 1
Sync Out
Sync In
System Ground
www.irf.com
9
AFL50XXS Series
Mechanical Outlines
Case X
Case W
Pin Variation of Case Y
3.000
ø 0.128
2.760
0.050
0.050
0.250
0.250
1.000
1.000
Ref
1.260 1.500
0.200 Typ
Non-cum
Pin
ø 0.040
Pin
ø 0.040
0.220
2.500
0.220
0.525
2.800
2.975 max
0.238 max
0.42
0.380
Max
0.380
Max
Case Y
Case Z
Pin Variation of Case Y
1.150
0.300
ø 0.140
0.25 typ
0.050
0.050
0.250
0.250
1.000
Ref
1.500 1.750 2.00
1.000
Ref
0.200 Typ
Non-cum
Pin
ø 0.040
Pin
ø 0.040
0.220
0.220
1.750
2.500
0.375
0.36
2.800
2.975 max
0.525
0.238 max
0.380
Max
0.380
Max
Tolerances, unless otherwise specified: .XX
.XXX
=
=
±0.010
±0.005
BERYLLIAWARNING: These converters are hermetically sealed; however they contain BeO substrates and should not be ground or subjected to any other
operations including exposure to acids, which may produce Beryllium dust or fumes containing Beryllium
10
www.irf.com
AFL50XXS Series
Pin Designation
Pin #
Designation
1
2
+ Input
Input Return
Case Ground
Enable 1
3
4
5
Sync Output
Sync Input
+ Output
6
7
8
Output Return
Return Sense
+ Sense
9
10
11
12
Share
Enable 2
Standard Microcircuit Drawing Equivalence Table
Standard Microcircuit
Drawing Number
5962-02557
IR Standard
Part Number
AFL5005S
5962-02558
AFL5008S
5962-02559
AFL5009S
5962-02560
AFL5012S
5962-02561
AFL5015S
5962-02562
AFL5028S
www.irf.com
11
AFL50XXS Series
Device Screening
Requirement
MIL-STD-883 Method No Suffix
ES
HB
CH
Temperature Range
Element Evaluation
Non-Destructive
Bond Pull
-20°C to +85°C -55°C to +125°C
-55°C to +125°C -55°C to +125°C
MIL-PRF-38534
2023
N/A
N/A
N/A
N/A
Class H
N/A
N/A
N/A
Internal Visual
Temperature Cycle
Constant Acceleration
PIND
2017
1010
Yes
Cond B
500 Gs
N/A
Yes
Cond C
3000 Gs
N/A
Yes
Cond C
3000 Gs
N/A
N/A
N/A
2001, Y1 Axis
2020
N/A
Burn-In
1015
N/A
48 hrs@hi temp 160 hrs@125°C 160 hrs@125°C
Final Electrical
( Group A )
MIL-PRF-38534
& Specification
MIL-PRF-38534
1014
25°C
25°C
-55°C, +25°C,
+125°C
N/A
-55°C, +25°C,
+125°C
10%
PDA
N/A
Cond A
N/A
N/A
Cond A, C
N/A
Seal, Fine and Gross
Radiographic
External Visual
Notes:
Cond A, C
N/A
Cond A, C
N/A
2012
2009
Yes
Yes
Yes
Best commercial practice
Sample tests at low and high temperatures
-55°C to +105°C for AHE, ATO, ATW
Part Numbering
AFL 50 05
S X /CH
Screening Level
Model
(Please refer to Screening Table)
No suffix, ES, HB, CH
Input Voltage
28 = 28V
50 = 50V
120 = 120V
270 = 270V
Case Style
W, X, Y, Z
Output
S = Single
Output Voltage
05 = 5V, 06 = 6V
07 = 7V, 08 = 8V
09 = 9V, 12 = 12V
15 = 15V, 28 = 28V
WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331
IR SANTA CLARA: 2270 Martin Av., Santa Clara, California 95050, Tel: (408) 727-0500
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 12/2006
12
www.irf.com
相关型号:
AFL5015SWPBF
DC-DC Regulated Power Supply Module, 1 Output, 120W, Hybrid, HERMETIC SEALED, CERAMIC PACKAGE-12
INFINEON
AFL5015SX/CHPBF
DC-DC Regulated Power Supply Module, 1 Output, 120W, Hybrid, HERMETIC SEALED, CERAMIC PACKAGE-12
INFINEON
AFL5015SX/ESPBF
DC-DC Regulated Power Supply Module, 1 Output, 120W, Hybrid, HERMETIC SEALED, CERAMIC PACKAGE-12
INFINEON
AFL5015SX/HBPBF
DC-DC Regulated Power Supply Module, 1 Output, 120W, Hybrid, HERMETIC SEALED, CERAMIC PACKAGE-12
INFINEON
©2020 ICPDF网 联系我们和版权申明