AMF2812D-EM [INFINEON]
28V Input, Dual Output, ADVANCED ANALOG RADIATION TOLERANT DC/DC CONVERTERS; 28V输入,双路输出,先进的模拟抗辐射DC / DC转换器型号: | AMF2812D-EM |
厂家: | Infineon |
描述: | 28V Input, Dual Output, ADVANCED ANALOG RADIATION TOLERANT DC/DC CONVERTERS |
文件: | 总7页 (文件大小:69K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD - 94688
AMF28XXD SERIES
28V Input, Dual Output
ADVANCED ANALOG
RADIATION TOLERANT
DC/DC CONVERTERS
Description
The AMF28XXD series of DC/DC converter modules
has been specifically designed for operation in moder-
ate radiation environments supplementing the higher
radiation performance available in the Advanced Ana-
log ART2815T converter series. Environments pre-
sented to space vehicles operating in low earth orbits,
launch boosters, orbiting space stations and similar
applications requiring a low power, high performance
converter with moderate radiation hardness perfor-
mance will be optimally served by the AMF28XXD se-
ries.
AMF
Features
n 12 Watts Output Power
n Available in ±5, ±12 and ±15 Volt Outputs
n 16 - 40 VDC Input Range (28 VDC Nominal)
n Low Input/Output Noise
n Total Ionizing Dose > 30KRads (Si)
n
The physical configuration of the AMF28XXD series
permits mounting directly to a heat conduction surface
without the necessity of signal leads penetrating the
heat sink surface. This package configuration permits
greater independence in mounting and more mechani-
cal security than traditional packages. Advanced
Analog’s rugged ceramic seal pins are used exclusively
in the package thereby assuring long term hermeticity.
No SEE to LET > 60 MeV-cm2/mg
-55°C to +125°C Operating Range
n
n Indefinite Short Circuit Protection
n
Flexible Mounting
n
High Power Density
n Fully Isolated - Input to Output and to Case
n Complimentary EMI Filter Available
n Externally Synchronizable
n Electrical Performance Similar to
AHF28XXD Series
The AMF28XXD has been designed for high density
using chip and wire hybrid technology that complies
with the class H requirements of MIL-PRF-38534. Fin-
ished product are fabricated in a facility fully qualified
to MIL-PRF-38534. The standard processing adopted
for the AMF28XXD meets the requirements of MIL-PRF-
38534 for class H but with enhanced screening steps
and includes element evaluation. Applicable generic
lot qualification test data including radiation perfor-
mance can be made available on request. Consult
Advanced Analog for special requirements.
www.irf.com
1
07/25/03
AMF28XXD Series
Specifications
Absolute Maximum Ratings
Input Voltage Range
-0.5V to +50VDC
300°C for 10 seconds
65°C to +135°C
Soldering Temperature
Storage Case Temperature
Recommmended Operating Conditions
Input Voltage Range
Output Power
+16V to +40VDC
Less than or equal to 12W
-55°C to +125°C
Operating Case Temperature
Static Characteristics -55°C ≤ T
≤ +125°C, V =28 V
IN
±5%, C =0, unless otherwise specified.
DC
L
CASE
Group A
Parameter
Input Voltage
Subgroups
Test Conditions
Min
Nom Max Unit
16
28
40
V
Vin = 28 Volts, 10% load on
both outputs
Output Voltage
1
1
1
V
V
V
AMF2805D
AMF2812D
AMF2815D
±4.95
±5.00
±5.05
±11.88 ±12.00 ±12.12
±14.85 ±15.00 ±15.15
2, 3
2, 3
2, 3
V
V
V
AMF2805D
AMF2812D
AMF2815D
±4.90
±11.76
±14.70
±5.10
±12.24
±15.30
1, 2
Vin = 16, 28, 40 Volts
each output
Output Current
1, 2, 3
1, 2, 3
1, 2, 3
240
100
80
2160
900
mA
mA
mA
AMF2805D
AMF2812D
AMF2815D
each output
each output
720
1, 2
Vin = 28 Volts, 100% load
Output Power
1, 2, 3
1, 2, 3
1, 2, 3
12
12
12
W
W
W
AMF2805D
AMF2812D
AMF2815D
1, 3
Vin = 16, 28, 40 Volts,
100% load,
Output Ripple Voltage
1, 2, 3
1, 2, 3
1, 2, 3
25
25
25
60
60
60
mVPP
mVPP
mVPP
AMF2805D
BW = 20 Hz to 2 MHz
AMF2812D
AMF2815D
3
Output voltage Regulation
V
= 16, 28, 40 Volts
in
Iout = 10, 50%, and 100%
load
1, 2, 3
1, 2, 3
1, 2, 3
mV
mV
mV
±10
±10
±10
±25
±50
±50
Line
AMF2805D
AMF2812D
AMF2815D
1, 2, 3
1, 2, 3
1, 2, 3
mV
mV
mV
Load
AMF2805D
AMF2805D
AMF2805D
±10
±10
±10
±50
±50
±50
For Notes to Specifications, refer to page 5
2
www.irf.com
AMF28XXD Series
Static Characteristics (Continued) -55°C ≤ T
≤ +125°C, V =28 V
IN DC
±5%, C =0, unless otherwise specified.
CASE
L
Group A
Subgroups
Parameter
Test Conditions
Min
Nom
Max
Unit
5
Minimum 1.0 watt on both
outputs 10%-90% load
Cross Regulation
1, 2, 3
1, 2, 3
1, 2, 3
10
3
%
%
%
AMF2805D
AMF2812D
AMF2815D
3
Vin=28V,
Input Current
1, 2, 3
1, 2, 3
1, 2, 3
Iout=0, Inhibit (pin 1)=open
35
35
35
60
60
60
mA
mA
mA
No Load
AMF2805D
AMF2812D
AMF2815D
1, 2, 3
1, 2, 3
1, 2, 3
Inhibit (pin 1) shorted to input
return (pin 7)
8
8
8
12
12
12
mA
mA
mA
Inhibit
AMF2805D
AMF2812D
AMF2815D
3
Vin = 16, 28, 40 Volts, 100%
load, BW = 20 Hz to 2 MHz
Input Ripple Current
1, 2, 3
20
20
20
50
50
50
mAPP
mAPP
mAPP
AMF2805D
AMF2812D
AMF2815D
1, 2, 3
1, 2, 3
3
100% load
Efficiency
76
77
78
%
%
%
AMF2805D
AMF2812D
AMF2815D
1, 3
1, 3
1, 3
72
74
74
%
%
%
AMF2805D
AMF2812D
AMF2815D
2
2
2
1
4
Input to output or any pin to
case (except pin 6) at 500Vdc
100
Isolation
MΩ
5, 6
No effect on dc performance,
total for both outputs
Capacitive Load
500
200
200
AMF2805D
AMF2812D
AMF2815D
µF
µF
µF
1, 2, 3
Short Circuit Power Dissipation
6
watts
Khrs
MIL-HDBK-217F, SF @
Tc=35°C
750
MTBF
36
g
Weight
For Notes to Specifications, refer to page 5
www.irf.com
3
AMF28XXD Series
Dynamic Characteristics -55°C ≤ T
≤ +125°C, V =28 V ±5%, C =0, unless otherwise specified.
IN DC
L
CASE
Group A
Parameter
Subgroups
Test Conditions
Min
Nom
Max
Unit
6
Short Circuit Recovery
0% load to 100% Load
4, 5, 6
4, 5, 6
4, 5, 6
25
25
25
ms
ms
ms
AMF2805D
AMF2812D
AMF2815D
3
4, 5, 6
100% load
500
550
600
KHz
Switching Frequency
3
Synchronization Input
4, 5, 6
500
2.5
700
10
KHz
V
Frequency Range
6
Pulse Amplitude, Hi
6
-0.5
0.8
100
80
V
Pulse Amplitude, Lo
6
ns
%
Pulse Rise time
6
20
Pulse Duty Cycle
Output Response To Step Transient
3, 7
Load Changes
4, 5, 6
4, 5, 6
Load step 50%ó100%
Load step 10% ó50%
-200
+200
+800
mV
pk
pk
--800
mV
Recovery Time, Step Transient Load
3, 7, 8
Changes
ó
Load step 50% 100%
4, 5, 6
4, 5, 6
70
µs
µs
ó
Load step 10% 50%
2000
Input step 16ó40Vdc,
Output Response Transient Step Line
3, 6, 9
100% Load
Changes
4, 5, 6
4, 5, 6
4, 5, 6
-450
-750
-750
+450
+750
+750
mV
AMF2805D
AMF2812D
AMF2815D
pk
pk
pk
mV
mV
Input step 16 ó40Vdc,
Recovery Time Transient Step Line
3, 6, 9
100% load
Changes
4, 5, 6
1200
µs
3, 10
Turn On Overshoot
4, 5, 6
0% load
600
mV
All
pk
4, 5, 6
4, 5, 6
4, 5, 6
100% load
400
300
300
AMF2805D
AMF2812D
AMF2815D
mV
mV
mV
pk
pk
pk
3, 10
Turn On Delay
4, 5, 6
0% load to 100% load
25
ms
For Notes to Specifications, refer to page 5
4
www.irf.com
AMF28XXD Series
Notes to Specifications
1. Applicable to positive and negative outputs.
2. Maximum combined output is 12 watts. 10.8 watts (max.) is available from either output (90%).
3. Load current split equally between +VOUT and VOUT
.
4. 1.2 watt load on output under test, 1.2 watt to 10.8 watt load change on other output.
5. Capacitive value may be any value from 0 to the maximum limit without compromising DC performance. A
capacitive load in excess of the maximum limit will not disturb loop stability but may interfere with the operation
of the load fault detection circuitry, appearing as a short circuit during turn-on.
6. Parameter shall be tested as part of design characterization and after design or process changes. Thereafter,
parameters shall be guaranteed to the limit specified.
7. Load step transition time between 2 and 10 microseconds.
8. Recovery time is measured from initiation of the transient to where Vout has returned to within ±1% of Vout at
50% load.
9. Input step transient time between 1 and 10 microseconds.
10. Turn-on delay time measurement is for either a step application of power at the input or the removal of a ground
signal from the inhibit pin while power is applied to the input.
AMF28XXD Block Diagram
3
+V out
E M I
8
Filter
+Input
4
5
R eturn
-Vout
P rim ary
H ousekeeping
S upply
1
E nable
6
C ase
Drive
Error
Amp &
Ref
P ulse W idth
M odulator
2
FB
CS
S ync
Input
R eturn
7
Application Information
Inhibit Function
Device Synchronization
Connecting the enable input (Pin 1) to input common
(Pin 7) will cause the converter to shut down. It is
recommended that the enable pin be driven by an
open collector device capable of sinking at least 400
µA of current. If the user chooses not to use the inhibit
function, it may be left open and the converter will
function normally. Because it is internally pulled up,
the open circuit voltage of the inhibit input is 10.0
+1VDC.
When multiple DC/DC converters are utilized in a
single system, significant low frequency noise may
be generated due to a small difference in the switch-
ing frequency of the converters (beat frequency
noise). Because of the low frequency nature of this
noise (typically less than 10 KHz), it is difficult to
filter out and may interfere with proper operation of
sensitive systems (communication, radar or telem-
etry). Advanced Analog provides synchronization
of multiple AMF type converters to match switching
frequency of the converter to the frequency of the
system clock, thus eliminating this type of noise.
EMI Filter
An optional EMI filter is available (AFH461) that will
reduce the input ripple current to levels below the
limits imposed by MIL-STD-461 CE03.
www.irf.com
5
AMF28XXD Series
Standard Process Screening for AMF28XXD Series
Requirement
MIL-STD-883 Method
CH+ Limits
Temperature Range
-55°C to +125°C
MIL-PRF-38534
Yes
Element Evaluation
Internal Visual
2017
1010
2001
2020
1015
Condition C
Condition A, (3000g)
Condition A
Temperature Cycle
Constant Acceleration
PIND
320 hrs @ +125°C
(2 x 160 hrs)
Burn-in
Interim Electrical; @160 hrs
MIL-PRF-38534
& Specification
-55°C, +25°C, +125°C
Final Electrical (Group A)
Read & Record Data
2%
Yes
PDA (25C, interim to final)
Radiographic Inspection
Fine & Gross
2012
1014
2009
Condition A, C
Yes
External Visual
Radiation Specification
Parameter
Condition
Min
Typ
Max
Unit
Total Ionizing Dose
MIL-STD-883, Method 1019.4
30
KRads
(Si)
Operating bias applied during exposure
2
MeV •cm
/mg
Heavy Ion
BNL Dual Van de Graf Generator
60
(Single event effects)
6
www.irf.com
AMF28XXD Series
AMF28XXD Case Outline
1.130
Ø 0.140
0.17
0.03D x 0.25L
8 Pins
1.850 1.600
2.10
1.000
0.800
0.600
0.400
0.19
0.33
1.380
Tolerance unless otherwise specified:
x.xx ±0.010
x.xxx ±0.005
Part Numbering
AMF 28 05 D / EM
Screening
Pin Designation
Pin No.
Designation
Model
1
2
3
4
5
6
7
8
Enable
Blank = Flight Model (CH+)
/EM = Engineering Model
Sync Input
Input Voltage
Outputs
S = Single
D = Dual
28 = 28V
Positive Output
Output Return
Negative Output
Case Ground
Input Return
Positive Input
Output Voltage
05 = ±5V,
12 = ±12V,
15 = ±15V
WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331
ADVANCED ANALOG: 2270 Martin Av., Santa Clara, California 95050, Tel: (408) 727-0500
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 07/03
www.irf.com
7
相关型号:
©2020 ICPDF网 联系我们和版权申明