AMR2803R3D/EM [INFINEON]
HYBRID - HIGH RELIABILITY RADIATION TOLERANT DC/DC CONVERTER; 混合 - 高可靠性抗辐射DC / DC转换器型号: | AMR2803R3D/EM |
厂家: | Infineon |
描述: | HYBRID - HIGH RELIABILITY RADIATION TOLERANT DC/DC CONVERTER |
文件: | 总7页 (文件大小:123K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD-94690B
AMR28XXD SERIES
28V Input, Dual Output
HYBRID - HIGH RELIABILITY
RADIATION TOLERANT
DC/DC CONVERTER
Description
The AMR28XXD series of DC/DC converter modules
has been specifically designed for operation in
moderate radiation environments supplementing the
higher radiation performance available in the
International Rectifier ART2815T converter series.
Environments presented to space vehicles operating
in low earth orbits, launch boosters, orbiting space
stations and similar applications requiring a low power,
high performance converter with moderate radiation
hardness performance will be optimally served by the
AMR28XXD series.
AMR
Features
n 30 Watts Output Power
n Available in ± 5, ±12 and ±15 Volt Outputs
n 16 - 40 VDC Input Range (28 VDC Nominal)
n Total Ionizing Dose > 25KRads (Si)
n SEE Hardened to LET up to 60 MeV.cm2/mg
-55°C to +125°C Operating Range
n Indefinite Short Circuit Protection
n External Synchronization
Shutdown from External Signal
Flexible Mounting
n Fully Isolated - Input to Output and to Case
n Complimentary EMI Filter Available
n Electrical Performance Similar to
ATR28XXD Series
The physical configuration of the AMR28XXD series
permits mounting directly to a heat conduction surface
without the necessity of signal leads penetrating the
heat sink surface. This package configuration permits
greater independence in mounting and more mechanical
security than traditional packages. International
Rectifier’s rugged ceramic seal pins are used
exclusively in the package thereby assuring long term
hermeticity.
n
n
n
The AMR28XXD has been designed for high density
using chip and wire hybrid technology that complies
with class H requirement of MIL-PRF-38534.
Manufactured in a facility fully qualified to MIL-PRF-
38534, these converters are fabricated utilizing DSCC
qualified processes. For available screening options,
refer to device screening table in the data sheet.
Applicable generic lot qualification test data including
radiation performance can be made available on
request. Variations to the standard screening can be
accommodated. Consult IR Santa Clara for special
requirements.
www.irf.com
1
09/15/08
AMR28XXD Series
Specifications
Absolute Maximum Ratings
Recommended Operating Conditions
Input Voltage range
-0.5V to +50VDC (Continuous), Input Voltage range
+16V to +40VDC
80V (100ms)
Output Power
Less than or equal to 30W
Soldering temperature
300°C for 10 seconds
Operating case temperature -55°C to +125°C
Storage case temperature -65°C to +135°C
Static Characteristics -55°C ≤ T
≤ +125°C, V =28 V
IN
±5%, C =0, unless otherwise specified.
DC
L
CASE
Group A
Subgroups
Parameter
Input Voltage
Test Conditions
Min
Nom
Max
Unit
16
28
40
V
Iout=0
Output Voltage
1
1
1
±
±
±
5.05
AMR2805D
AMR2812D
AMR2815D
4.95
5.00
±11.88 ±12.00 ±12.12
±
±
±
14.85 15.00 15.15
V
AMR2805D
AMR2812D
AMR2815D
2, 3
2, 3
2, 3
±4.90
±11.70
±14.70
±5.10
±12.30
±15.30
Output Current 1, 2
Output Power
Vin = 16, 28, 40 Volts
100% load
600
250
200
5400
2250
1800
AMR2805D
AMR2812D
AMR2815D
1, 2, 3
1, 2, 3
1, 2, 3
mA
W
30
30
30
AMR2805D
AMR2812D
AMR2815D
1, 2, 3
1, 2, 3
1, 2, 3
Output Ripple Voltage 3
AMR2805D
Vin = 16, 28, 40 Volts
BW = 20 Hz to 2 MHz
60
85
85
1, 2, 3
1, 2, 3
1, 2, 3
mVPP
AMR2812D
AMR2815D
Output Voltage Regulation4
V
= 16, 28, 40 Volts
in
Iout = 0, 50%, and 100% load
1, 2, 3
1, 2, 3
1, 2, 3
±
±30
±40
±
30
±75
±75
10
Line
AMR2805D
AMR2812D
AMR2815D
mV
1, 2, 3
1, 2, 3
1, 2, 3
Load
AMR2805D
AMR2812D
AMR2815D
±10
±50
±50
±50
±120
±150
For Notes to Specifications, refer to page 5
2
www.irf.com
AMR28XXD Series
Static Characteristics (Continued) -55°C ≤ T
≤ +125°C, V =28 V
IN DC
±5%, C =0,unless otherwise pecified.
CASE
L
Group A
Subgroups
Parameter
Test Conditions
Min
Nom
Max
Unit
Cross Regulation 5
10% TO 90% Load change
1, 2, 3
1, 2, 3
1, 2, 3
10
5.0
5.0
AMR2805D
AMR2812D
AMR2815D
%
Input Current
Iout=0, Inhibit =open
No Load
AMR2805D
AMR2812D
AMR2815D
1, 2, 3
1, 2, 3
1, 2, 3
20
20
20
70
75
100
mA
Inhibit shorted to input return
1, 2, 3
1, 2, 3
1, 2, 3
8.0
8.0
8.0
15
18
18
Inhibit
AMR2805D
AMR2812D
AMR2815D
Input Ripple Current 3, 4
Vin = 16, 28, 40 Volts, 100%
load, BW = 20 Hz to 2 MHz
1, 2, 3
50
mAPP
Efficiency 4
100% load
76
80
79
AMR2805D
AMR2812D
AMR2815D
1
1
1
%
72
75
74
AMR2805D
AMR2812D
AMR2815D
2, 3
2, 3
2, 3
1
Input to output or any pin to
case (except case ground pin)
at 500Vdc
100
MΩ
Isolation
Capacitive Load 6, 7
4
No effect on dc performance
200
9.0
µF
W
1, 2, 3
4, 5, 6
4, 5, 6
Short Circuit Power Dissipation
Switching Frequency 4
Sync frequency range
MTBF
100% load
100% load
500
500
800
550
600
700
KHz
KHz
Khrs
MIL-HDBK-217F, SF@
Tc=35°C
68
g
Weight
For Notes to Specifications, refer to page 5
www.irf.com
3
AMR28XXD Series
Dynamic Characteristics -55°C ≤ T
≤ +125°C, V =28 V
±5%, C =0, unless otherwise specified.
DC
L
CASE
Group A
IN
Parameter
Subgroups
Test Conditions
Min
Nom
Max
Unit
Output Response To Step
4, 9
Transient Load Changes
Load step 50% 100%
AMR2805D
AMR2812D
AMR2815D
4, 5, 6
4, 5, 6
4, 5, 6
-400
-400
-400
+400
+400
+400
mV pk
Load step 0%
50%
AMR2805D
AMR2812D
AMR2815D
4, 5, 6
4, 5, 6
4, 5, 6
-400
-800
-800
+400
+800
+800
Recovery Time, Step Transient
Load Changes 4, 9, 10
Load step 50% 100%
AMR2805D
AMR2812D
AMR2815D
4, 5, 6
4, 5, 6
4, 5, 6
70
70
70
s
s
µ
Load step 0% => 50%
Load step 50% => 0%
AMR2805D
AMR2812D
AMR2815D
4, 5, 6
4, 5, 6
4, 5, 6
500
500
500
µ
5
5
5
AMR2805D
AMR2812D
AMR2815D
4, 5, 6
4, 5, 6
4, 5, 6
ms
Output Response Transient Step
Line Changes 4, 7, 11
AMR2805D
Input step from/to 16 to 40Vdc,
100% load
4, 5, 6
4, 5, 6
4, 5, 6
-500
-1200
-1500
+500
+1200
+1500
AMR2812D
AMR2815D
mV pk
Recovery Time Transient Step Line
Changes 4, 7, 10, 11
AMR2805D
Input step from/to 16 to 40Vdc,
100% load
4, 5, 6
4, 5, 6
4, 5, 6
10
10
10
AMR2812D
AMR2815D
ms
Turn On Overshoot 4
AMR2805D
4, 5, 6
4, 5, 6
4, 5, 6
0% load to 100% load
0% load to 100% load
450
600
750
AMR2812D
AMR2815D
mV pk
ms
Turn On Delay 4, 12
AMR2805D
4, 5, 6
4, 5, 6
4, 5, 6
25
25
25
AMR2812D
AMR2815D
Short Circuit Recovery 7
AMR2805D
4, 5, 6
4, 5, 6
4, 5, 6
25
25
25
AMR2812D
AMR2815D
ms
For Notes to Specifications, refer to page 5
4
www.irf.com
AMR28XXD Series
Notes to Specifications
1. Parameter guaranteed by line and load regulation tests.
2. Up to 90 percent of full power is available from either output provided the total output does not exceed 30 watts.
3. Bandwidth guaranteed by design, Tested for 20 Hz to 2 MHz.
4. Load current split equally between +VOUT and –VOUT
.
5. 3 watt load on output under test. 3 watt to 27 watt load change on other output.
6. Capacitive load may be any value from 0 to the maximum limit without compromising DC performance. A
capacitive load in excess of the maximum limit will not disturb loop stability but may interfere with the operation
of the load fault detection circuitry, appearing as a short circuit during turn-on.
7. Parameter shall be tested as part of design characterization and after design or process changes, Parameters
shall be guaranteed to the limit specified in Electrical Specifications.
8. Load step transition time between 2 and 10 microseconds.
±
9. Recovery time is measured from initiation of the transient to where Vout has returned to within 1% of Vout at
50% load.
10. Input step transient time between 2 and 10 microseconds.
11. Turn-on delay time measurement is for either a step application of power at the input or the removal of a ground
signal from the inhibit pin while power is applied to the input.
Block Diagram
EMI
Filter
1
+Input
8
+Output
Under-Voltage
Detector
Output
Return
7
6
Primary
Housekeeping
Supply
3
-Output
Enable
5
Case
Drive
Pulse Width
Modulator
Error
Amp &
Ref
10
FB
CS
Sync
Input
Input
Return
2
Device Synchronization
Application Information
Inhibit Function (Enable)
Connecting the inhibit input to input common will
cause the converter to shut down. It is recommended
that the inhibit pin be driven by an open collector
device capable of sinking at least 400 µA of current.
The open circuit voltage of the inhibit input is 10 ±1.0 VDC.
When multiple DC/DC converters are utilized in a
single system, significant low frequency noise may
be generated due to a small difference in the
switching frequency of the converters (beat
frequency noise). Because of the low frequency
nature of this noise (typically less than 10 KHz), it is
difficult to filter out and may interfere with proper
operation of sensitive systems (communication,
radar or telemetry). International Rectifier provides
synchronization of multiple AMR type converters to
match switching frequency of the converter to the
frequency of the system clock, thus eliminating this
type of noise.
EMI Filter
An optional EMI filter is available (AFH461) that will
reduce the input ripple current to levels below the
limits imposed by MIL-STD-461 CE03.
www.irf.com
5
AMR28XXD Series
Mechanical Outline
0.220
0.050
Ø 0.125
3 Places
R 0.15 Typ
0.040 D x 0.26 L Pins
2.74
Ref
1.600 2.440
2.14
1.200
0.800
0.400
0.420
0.150
Typ
1.230
1.53
0.410
Max
Tolerance unless otherwise specified:
x.xx ±0.010
x.xxx ±0.005
Pin Designation
Pin #
Designation
1
2
+ Input
Input Return
Enable
3
4
Blank
Case Ground
- Output
5
6
7
Output Return
+ Output
8
9
NC
10
Sync Input
Radiation Specification
Parameter
Condition
Min
Typ
Max
Unit
Total Ionizing Dose
MIL-STD-883, Method 1019.4
Operating bias applied during exposure
25
-
-
KRads
(Si)
2
Heavy Ion
(Single event effects)
BNL Dual Van de Graf Generator
60
-
-
•
MeV cm
/mg
International Rectifier currently does not have a DSCC certified Radiation Hardness Assurance Program.
6
www.irf.com
AMR28XXD Series
Device Screening
Requirement
MIL-STD-883 Method
No Suffix
CH
EM
Temperature Range
Element Evaluation
Non-Destructive Bond Pull
Internal Visual
-55°C to +125°C
Class H
N/A
-55°C to +125°C
Class H
N/A
-55°C to +85°C
MIL-PRF-38534
2023
N/A
N/A
2017
Yes
Yes
Temperature Cycle
Constant Acceleration
PIND
1010
Cond C
Cond C
Cond C
3000 Gs
2001, Y1 Axis
2020
3000 Gs
Cond A
3000 Gs
Cond A
N/A
320 hrs @ 125°C
( 2 x 160hrs )
-55°C, +25°C,
+125°C
320 hrs @ 125°C
( 2 x 160hrs )
-55°C, +25°C,
+125°C
48 hrs @ 125°C
Burn-In
1015
Final Electrical
( Group A )
MIL-PRF-38534
& Specification
MIL-PRF-38534
1014
-55°C, +25°C,
+85°C
PDA
2%
2%
N/A
Seal, Fine and Gross
Radiographic
External Visual
Cond A, C
Yes
Cond A, C
Yes
Cond A
N/A
2012
2009
Yes
Yes
Notes:
Best commercial practice.
Device with ‘/CH’ suffix is a DSCC class H compliant without radiation performance. No suffix is a radiation rated
device but not available as a DSCC qualified SMD per MIL-PRF-38534.
International Rectifier currently does not have a DSCC certified Radiation Hardness Assurance Program.
Part Numbering
AMR 28 15 D /EM
Model
Screening Level
(Please refer to Screening Table)
Input Voltage
28 = 28V
No Suffix, CH, EM
Output
S = Single
D = Dual
T = Triple
Output Voltage
03R3 = 3.3V, 05 = 5V,
12 = 12V, 15 = 15V
WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 252-7105
IR SANTA CLARA: 2270 Martin Av., Santa Clara, California 95050, Tel: (408) 727-0500
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 09/2008
www.irf.com
7
相关型号:
©2020 ICPDF网 联系我们和版权申明