AUIR3313 [INFINEON]
PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH; 可编程电流检测高压侧开关型号: | AUIR3313 |
厂家: | Infineon |
描述: | PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH |
文件: | 总16页 (文件大小:596K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
December, 10th 2010
Automotive grade
AUIR3313(S)
PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH
Features
Product Summary
Load current feedback
Programmable over current shutdown
Active clamp
Rds(on)
Vcc op.
Current Ratio
7 m max.
6 to 32V
8800
ESD protection
Input referenced to Vcc
Over temperature shutdown
Reverse battery protection
Lead Free, RoHS compliant
Prog. Ishutdown 10 to 90A
Vclamp
40V
Packages
Description
The AUIR3313(S) is a fully protected 4 terminals high side
switch. The input signal is referenced to Vcc. When the
input voltage Vcc - Vin is higher than the specified
threshold, the output power Mosfet is turned on. When the
Vcc - Vin is lower than the specified Vil threshold, the
output Mosfet is turned off. A current proportional to the
power Mosfet current is sourced to the Ifb pin. Over
current shutdown occurs when Vifb-Vin > 4.7V. The
current shutdown threshold is adjusted by selecting the
proper RIfb. Either over current and over temperature
latches off the switch. The device is reset by pulling the
input pin high. Other integrated protections (ESD, reverse
battery, active clamp) make the switch very rugged in
automotive environment.
TO-220
AUIR3313
D²Pak
Pin 4 and 5 fused
AUIR3313S
Typical Connection
Vcc
AUIR3313
IN
Battery
Ifb
Out
Current feeback
10k
Input
Load
Rifb
On
Logic
Ground
Power
Ground
Off
1
www.irf.com
AUIR3313(S)
†
Qualification Information
Automotive
(per AEC-Q100††)
Qualification Level
Comments: This family of ICs has passed an Automotive qualification. IR’s
Industrial and Consumer qualification level is granted by extension of the
higher Automotive level.
MSL1, 260°C
D2PAK-5L
(per IPC/JEDEC J-STD-020)
Moisture Sensitivity Level
TO220-5L
Not applicable
Class M4 (450V)
(per AEC-Q100-003)
Machine Model
Class H3A (4,500 V)
ESD
Human Body Model
Charged Device Model
(
)
per AEC-Q100-002
Class C4 (1000 V)
(per AEC-Q100-011)
Class II, Level A
(per AEC-Q100-004)
IC Latch-Up Test
RoHS Compliant
Yes
†
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
††
Exceptions to AEC-Q100 requirements are noted in the qualification report.
2
www.irf.com
AUIR3313(S)
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are referenced to Vcc lead. (Tj=-40°..150°C, Vcc=6..26V Tambient=25°C unless otherwise specified).
Symbol
Parameter
Min. Max. Units
Vcc-Vin
Maximum Vcc voltage
-16
-16
-16
-0.3
37
32
33
37
2.8
100
2
Vcc-Vin cont. Maximum continuous Vcc voltage
V
Vcc-Vfb
Vcc-Vout
Ids cont.
Ids pulsed
Pd
Tj max.
Min Rfb
Ifb max.
Maximum Ifb voltage
Maximum output voltage
Maximum body diode continuous current Rth=60°C/W (1)
Maximum body diode pulsed current (1)
Maximum power dissipation Rth=60°C/W
Max. storage & operating temperature junction temperature
Minimum on the resistor on Ifb pin
Max. Ifb current
A
W
°C
k
-40
0.3
-50
150
50
mA
(1) Limited by junction temperature. Pulsed is also limited by wiring
Thermal Characteristics
Symbol
Rth1
Parameter
Typ. Max. Units
60
Thermal resistance junction to ambient D²-Pak Std footprint
Thermal resistance junction to case D²-Pak
Thermal resistance junction to case TO220
Rth2
Rth2
0.7
0.7
°C/W
Recommended Operating Conditions
These values are given for a quick design. For operation outside these conditions, please consult the application notes.
Symbol
Parameter
Min. Max. Units
Iout
Continuous output current
A
Tambient=85°C, Rth=5°C/W, Tj=125°C
Tambient=85°C, Rth=60°C/W, Tj=125°C
Recommended Ifb resistor (2)(3)
Minimum turn-on pulse width
Maximum operating frequency
23
7
3.5
Rifb
Pulse min.
Fmax.
0.3
1
k
ms
Hz
200
(2) If Rifb is too low, the device can be damaged.
(3) If Rifb is too high, the device may not switch on.
3
www.irf.com
AUIR3313(S)
Protection Characteristics
Tj=-40°..150°C, Vcc=6..26V, Rifb=300 to 5k
Symbol
Parameter
Min. Typ. Max. Units
Test Conditions
Vifb-Vin@Isd Over-current shutdown threshold
3.8
4.7
165
35
120
40
5.9
V
°C
V
Tsd
Over temperature threshold
See fig. 5
OV
Isdf
Over voltage protection (not latched)
Fixed over current shutdown
33
90
30
39
150
53
Vifb<Vifb-Vin@Isd
Rifb=1k
A
Isd_1k
Programmable over current shutdown 1k
treset
Min. pulse
WAIT
Time to reset protection
Min. pulse width (no WAIT state)
WAIT function timer
Reverse battery On state resistance
Tj=25°C
50
400
1
500
1200
2
See fig. 5
Tj=25°C
See fig. 4 and 5
Vcc-Vin=-14V,
Iout=30A
µs
150
0.4
4
ms
m
Rds(on) rev.
6.7
10
Tj=125°C
10
15
Static Electrical Characteristics
Tj=-40°..150°C, Vcc=6..26V (unless otherwise specified)
Symbol
Vcc op.
Icc off
Parameter
Operating Voltage range
Supply leakage current
Min.
6
Typ. Max. Units Test Conditions
32
V
1.5
5
Vin=Vcc, Vcc-Vout=14V,
Vcc-Vifb=14V, Tj=25°C
Vcc-Vin=14V, Tj=25°C
µA
mA
Iin, on
Vih
Vil
Vhyst
Iout
On state IN positive current
1.5
3
6
High level Input threshold voltage (4)
Low level Input threshold voltage (4)
Input hysteresis Vih-Vil
5.4
4.9
0.4
1.2
6.3
5.8
1.5
5
4
0.2
V
µA
m
Drain to source leakage current
Vin=Vcc, Vcc-Vifb=0V,
Vcc-Vout=14V, Tj=25°C
Iout=30A, Vcc-Vin=14V
Iout=17A, Vcc-Vin=6V
Rds(on)
On state resistance (5) Tj=25°C
On state resistance (5) Tj=25°C
On state resistance (5)(6) Tj=150°C
Vcc to Vout clamp voltage 1
5.5
6
7
10
10.5
39
40
13.5
Iout=30A, Vcc-Vin=14V
Iout=50mA
Iout=30A, Tj=25°C
V clamp1
V clamp2
36
V
Vcc to Vout clamp voltage 2
43
(4) Input thresholds are measured directly between the input pin and the tab. Any parasitic resistance in common between
the load current path and the input signal path can significantly affect the thresholds.
(5) Rdson is measured between the tab and the Out pin, 5mm away from the package.
(6) Guaranteed by design
Switching Electrical Characteristics
Vcc=14V, Resistive load=0.5 , Tj=25°C
Symbol
tdon
tr1
Parameter
Min. Typ. Max. Units Test Conditions
Turn on delay time to 10% Vcc
Rise time to Vcc-Vout=5V
Rise time to Vcc-Vout=0.1Vcc
Turn on energy
Turn off delay time
Fall time to Vout=10% of Vcc
Turn off energy
8
3
6
32
16
40
4.5
80
32
2
80
40
90
µs
tr2
Eon
tdoff
tf
mJ
µs
See figure 2
20
8
200
80
Eoff
mJ
4
www.irf.com
AUIR3313(S)
Current Sense Characteristics
Tj=-40°..150°C, Vcc=6..26V (unless otherwise specified)
Symbol
Ratio
Ratio_TC
Offset
Parameter
I Load/Iifb current ratio
I Load/Iifb variation aver temperature(6)
Load current diagnostic offset
Ifb response time (low signal)
Min. Typ. Max. Units
8200 8,800 9,950
Test Conditions
Rfb=500 , Iout=60A
Tj=-40°C to 150°C
Iout=2A
-5
-0.2
+5
+0.3
%
A
µs
0
1
trst
90% of the Iout step
Functional Block Diagram
All values are typical
VCC
Driver
Charge
Pump
On/Off
Fast turn-off
43V
38V
43V
3mA
+
-
+
-
35V
43V
Reset
LatchQ
Set
Wait
timer
1 ms
-
4.7V
timer
400µs
+
Min. Pulse
-
+
Iout > 120A
Tj > 165°C
reverse
battery
protection
IN
IFB OUT
5
www.irf.com
AUIR3313(S)
Lead Assignments
90%
Vcc-Vin
Vih
Vil
Icc
Vcc-Vin
Vcc-Vout
Vclamp1
Vclamp2
10%
tr-in
Vhyst
Vcc
IR3313
Out
IN
90%
Vcc-5V
Iin
Ifb
Vout
Ifb
10%
td on
td off
Iout
Isd
tr1
tf
tr2
Figure 1 – Voltages and current definitions
Figure 2 – Switching time definitions
6
www.irf.com
AUIR3313(S)
t clamp
Vcc-Vin
Vin
Iout
t min. pulse
t min. pulse
Wait
Vcc
Iout
Vout
Vcc - V clamp
See Application Notes to evaluate power dissipation
Figure 3 – Active clamp waveforms
Figure 4 – Min. pulse and Wait function
Vcc-Vin
t < t reset
t > t reset
Wait
t < t reset
t > t reset
Wait
Over-current shutdown
Iout
Over-temperature shutdown
Tj
Figure 5 – Protection Timing Diagrams
7
www.irf.com
AUIR3313(S)
All curves are typical characteristics. Operation in hatched areas is not recommended. Tj=25°C, Rifb=500ohm, Vcc=14V
(unless otherwise specified).
10
6
5
8
4
6
3
4
2
2
1
0
0
0
10
20
30
40
50
-50
0
50
100
150
Vcc-Vin, supply voltage (V)
Tj, junction temperature (°C)
Figure 6 – Icc (mA) Vs Vcc-Vin (V)
Figure 7 – Icc off (µA) Vs Tj (°C)
200%
150%
100%
50%
6
5
4
3
2
1
0
Vifb-Vin@Isd
VIH
VIL
-50
0
50
100
150
-50 -25
0
25
50
75 100 125 150
Tj, junction temperature (°C)
Tj, junction temperature (°C)
Figure 8 - Normalized Rds(on) (%) Vs Tj (°C)
Figure 9 – Vih, Vil and Vifb-Vin@Isd (V) Vs Tj (°C)
8
www.irf.com
AUIR3313(S)
18
16
14
12
10
8
100
With calibration
Spec. Max.
6
4
2
0
10
0
20
40
60
80
100
100
1000
10000
I load, load current (A)
Rifb, feedback resistor (
)
Figure 10 – Error (+/- A) Vs I load (A)
Figure 11 – Ids (A) Vs Rifb ( )
30
20
10
0
100
60°C/W
35°C/W
10
-50
0
50
100
150
10
100
1000
Inductance (µH)
Tamb., ambient temperature (°C)
Figure 12 – Max. Iout (A) Vs Tamb. (°C)
Figure 13 – Max. Iout (A) Vs inductance (µH)
9
www.irf.com
AUIR3313(S)
100
10
100
Tamb=25°C
50°C/W free air
5°C/W
Tamb=100°C
1
0.1
0.01
10
1.E-01
1E-4
1E-3
1E-2
1E-1 1E+0 1E+1 1E+2
Time (s)
1.E+00
1.E+01
1.E+02
1.E+03
Protection response time (s)
Figure 14 – Ids (A) Vs over temperature
Figure 15 – Transient thermal impedance (°C/W)
protection response time (s)/ Rth=60°C/W
Vs time (s)
10
www.irf.com
AUIR3313(S)
Case Outline - TO220 - 5 Leads
11
www.irf.com
AUIR3313(S)
Case Outline - D2PAK - 5 Leads
12
www.irf.com
AUIR3313(S)
Tape & Reel - D2PAK – 5 leads
13
www.irf.com
AUIR3313(S)
Part Marking Information
Ordering Information
Standard Pack
Form
Base Part Number
Package Type
Complete Part Number
Quantity
50
TO220 – 5Leads
Tube
Tube
AUIR3313
AUIR3313S
50
AUIR3313
D2-Pak-5-Leads
Tape and reel left
Tape and reel right
800
AUIR3313STRL
AUIR3313STRR
800
14
www.irf.com
AUIR3313(S)
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR)
reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and
services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU”
prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and
process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order
acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with
IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to
support this warranty. Except where mandated by government requirements, testing of all parameters of each product is
not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their
products and applications using IR components. To minimize the risks with customer products and applications,
customers should provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and
is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with
alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation.
Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or
service voids all express and any implied warranties for the associated IR product or service and is an unfair and
deceptive business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into
the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the
IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products
for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of
the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR
products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as
military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has
not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all
legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR
products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the
designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive
applications, IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
15
www.irf.com
AUIR3313(S)
Revision History
Revision
Date
Notes/Changes
First release
Pbf version release
TO220 release
AU release
A
B
C
D
E
F
01/09/2006
22/01/2007
16/04/2008
14/04/2010
14/11/2010
10/12/2011
Change description section
Vcalmp specified at 25°C
16
www.irf.com
相关型号:
©2020 ICPDF网 联系我们和版权申明