CDM10V-3 [INFINEON]
CDM10V-3 是一个完全集成的 0-10V 调光接口 IC,采用6-引脚 SOT 封装,可以满足小型 PCB 的空间要求。该装置适用于各种调光应用。该 IC 可用于将基于模拟电压的信号以基于电流的PWM信号形式从0-10V调光器或电位器传输到照明控制器IC的调光或PWM输入,以驱动外部光电耦合器。;型号: | CDM10V-3 |
厂家: | Infineon |
描述: | CDM10V-3 是一个完全集成的 0-10V 调光接口 IC,采用6-引脚 SOT 封装,可以满足小型 PCB 的空间要求。该装置适用于各种调光应用。该 IC 可用于将基于模拟电压的信号以基于电流的PWM信号形式从0-10V调光器或电位器传输到照明控制器IC的调光或PWM输入,以驱动外部光电耦合器。 PC 驱动 控制器 CD 光电 装置 电位器 |
文件: | 总11页 (文件大小:558K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CDM10V-3
0-10V Dimming Solution
Feature list
•
Simplest 0-10 V design on the market. CDM10V-3 comes with following key settings:
-
-
-
1kHz PWM frequency
200μA Dimmer/Resistor Bias current
1% minimum Duty-Cycle
•
•
•
Wide input Vcc range from 11 to 25 V
Replaces many external components with a single chip reducing BOM and PCB space
Minimum variation from device to device
Potential Applications
•
•
LED Drivers needing 0-10 V Dimming Circuits
Industrial and Commercial Dimmable Applications:
Luminaires, Troffers, Downlights, Sconces, Undercabinet, Office Lighting, Signage applications,
Dali applications
Product Type
Package
CDM10V-3
SOT23-6
Product validation
Description
CDM10V-3 is a fully integrated 0-10 V dimming interface IC and comes in a SOT-23-6 package to cover space
requirements on small PCBs.
The device is targeted for various dimming applications in lighting. The IC can be used to transmit analog
voltage based signals from a 0-10 V dimmer or potentiometer to the dimming or PWM input of a lighting
controller IC in the form of a 5 mA current based PWM signal to drive an external opto-coupler. It replaces many
components in a traditional solution and reduces BOM and PCB space significantly.
The CDM10V-3 IC outputs a 1 - 100% PWM current signal at 1 kHz with an amplitude value of 5 mA.
Embedded digital signal processing maintains minimum variations from device to device.
Datasheet
Please read the Important Notice and Warnings at the end of this document
V1.0
www.infineon.com
2017-07-04
CDM10V-3
0-10V Dimming Solution
Table of contents
Table of contents
Feature list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Potential Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Block diagram reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical characteristics and parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1
2
3
4
5
6
Datasheet
2
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Block diagram reference
1
Block diagram reference
Figure 1
Block Diagram of the CDM10V-3
2
Pin configuration
Table 1
Pin configutation
Pin
1
Name
VCC
Function
Input supply voltage
2
GND
Iout
GND
3
PWM output current
4
NC
GND
GND
5
NC
6
Rdim+
Dimmer current output /Voltage sense
Datasheet
3
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Functional description
3
Functional description
Typical Application Circuit
Figure 2
Typical Application Circuit
Note:
The Diode marked with * is for the protection of the Rdim+-Pin when active dimming is used. This is
because the voltage on this Pin is not allowed to be higher than VCC+0.5V. It is advised to use a low
leakage, low reverse current Schottky-Diode in order to not influence the dimming performance (e.g.
MMSD301T1G).
Note:
The capacitor connected to the Rdim+-Pin reduces the amount of coupled noise to the dimming signal.
The size of this capacitance should be in the range of 2.2 - 10 nF (typ. 4.7 nF), where a small capacitor
allows steeper edges of the dimming signal, a larger capacitor enhances the noise reduction.
Recommended cooling area
In order to guarantee the full functionality of the CDM10V-3 device, the required cooling area has to be selected
according to the graph in Figure 3.
Datasheet
4
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Functional description
Figure 3
Cooling area over ambient temperature CDM10V-3
Datasheet
5
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Functional description
Dimming Characteristic
Table 2
PWM Output current referring to Rdim+-Pin Voltage
Rdim+
Iout
<1 V
1 - 9 V
1% Duty-Cycle
1…100% (@ 9V)
Always active
>9V (max. applicable Voltage: Vcc)
Figure 4
Dimming Characteristic
Datasheet
6
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Electrical characteristics and parameters
4
Electrical characteristics and parameters
Table 3
Pin
Absolute Maximum Ratings
Name
Values
Unit
Note or Test
Condition
Min.
Max.
1
2
3
Vcc
11
0
25
0
V
V
V
GND
Iout
Point of reference
-0.5
3.63
Depending on the
optocupler voltage
@ 5mA
4
5
6
NC
-0.25
-0.25
-0.5
0.1
0.1
V
V
V
Connect to GND
during operation
NC
Connect to GND
during operation
Rdim+
VCC + 0.5
An applied voltage
above max value
leads to the
destruction of the
device. Also valid if
VCC is 0 V.
Absolute maximum ratings (Table 3) are defined as ratings which when being exceeded may lead to destruction
of the integrated circuit. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause
irreversible damage to the integrated circuit. These values are not tested during production test.
Table 4
Electrical Characteristics
Symbol
Parameter
Values
Typ.
Unit Note or Test
Condition
Min.
11
Max.
25
Input Voltage
Vin
TJ
V
Operating Voltage
Junction Temperature
Range
-40
135
°C
Ambient Temperature
Range
TA
-40
105
°C
Power Dissipation
Ptot
6.05 @ 1%
duty cycle;
130 @ 100% duty 160 @ mW
Dimmer current
included
cycle
100%
PWM &
25 Vin
54 @ 50% duty
cycle
Current Consumption
ICC
1
mA
Current
Consumption of
the IC for self
supply
Output Current for
Dimmer
Idim
Iout
-10%
-10%
200
5
+10%
+10%
μA
Current flow out
of Rdim+-Pin
Output Current for
Optocoupler
mA
Datasheet
7
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Package dimensions
Table 4
Electrical Characteristics (continued)
Parameter
Symbol
Values
Typ.
Unit Note or Test
Condition
Min.
Max.
Dimming accuracy
-3
+3
%
With active
dimming incl. all
variations
PWM frequency
Min. duty cycle
fPWM
-6%
-0.2
1000
1
+6%
+0.2
Hz
%
PWPWM
Percentage of the
pulse width
Wake-up Time
ESD capability HBM
ESD capability CDM
tw
40
μs
V
Time from VCC
11 V to first
=
output current
VHAB
1500
500
according to
ANSI/ESDA/JEDEC
JS-001
VCDM
according to
JESD22 C101
5
Package dimensions
Package Drawings
Figure 5
Package Drawings
Datasheet
8
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
Package dimensions
Footprint
Figure 6
Footprint
Packing Description
Packing Type
Tape and Reel
∅ Reel: 180
Pieces / Reel:
3000
Reels / Box: 1
Figure 7
Packing
Datasheet
9
V1.0
2017-07-04
CDM10V-3
0-10V Dimming Solution
References
6
References
Additional support material can be found under the following link.
Related information
http://www.infineon.com/CDM10V
Revision history
Document
version
Date of
release
Description of changes
1.0
03.07.2017
•
•
Initial Version
Datasheet
10
V1.0
2017-07-04
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2017-07-04
Published by
IMPORTANT NOTICE
WARNINGS
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics (“Beschaffenheitsgarantie”) .
With respect to any examples, hints or any typical values
stated herein and/or any information regarding the
application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities of
any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer’s compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer’s products and any use of the product of
Infineon Technologies in customer’s applications.
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or
any consequences of the use thereof can reasonably
be expected to result in personal injury
Infineon Technologies AG
81726 Munich, Germany
a written document signed by
©
2017 Infineon Technologies AG
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Document reference
IFX-ipk1496737666819
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer’s technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to such
application.
相关型号:
CDM10V-4
CDM10V-4 是一个完全集成的 0-10V 调光接口 IC,采用6-引脚 SOT 封装,可以满足小型 PCB 的空间要求。该装置适用于各种调光应用。该 IC 可用于将基于模拟电压的信号以基于电流的PWM信号形式从0-10V调光器或电位器传输到照明控制器IC的调光或PWM输入,以驱动外部光电耦合器。
INFINEON
CDM22011-600LRFPSL
Power Field-Effect Transistor, 11A I(D), 600V, 0.36ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-220AB, TO-220FP, 3 PIN
CENTRAL
©2020 ICPDF网 联系我们和版权申明