CY7C1618KV18-333BZXC [INFINEON]
DDR-II CIO;型号: | CY7C1618KV18-333BZXC |
厂家: | Infineon |
描述: | DDR-II CIO 双倍数据速率 |
文件: | 总33页 (文件大小:768K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY7C1618KV18/CY7C1620KV18
144-Mbit DDR II SRAM Two-Word
Burst Architecture
CY7C1618KV18/CY7C1620KV18, 144-Mbit DDR II SRAM Two-Word Burst Architecture
Features
Configuration
■ 144-Mbit density (8M × 18, 4M × 36)
CY7C1618KV18 – 8M × 18
CY7C1620KV18 – 4M × 36
■ 333 MHz clock for high bandwidth
■ Two-word burst for reducing address bus frequency
Functional Description
■ Double data rate (DDR) interfaces (data transferred at
666 MHz) at 333 MHz
The CY7C1618KV18, and CY7C1620KV18 are 1.8-V
synchronous pipelined SRAM equipped with DDR II architecture.
The DDR II consists of an SRAM core with advanced
synchronous peripheral circuitry and a 1-bit burst counter.
Addresses for read and write are latched on alternate rising
edges of the input (K) clock. Write data is registered on the rising
edges of both K and K. Read data is driven on the rising edges
of C and C if provided, or on the rising edge of K and K if C/C are
not provided. On CY7C1618KV18 and CY7C1620KV18, the
burst counter takes in the least significant bit of the external
address and bursts two 18-bit words in the case of
CY7C1618KV18 and two 36-bit words in the case of
CY7C1620KV18 sequentially into or out of the device.
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
■ Two input clocks for output data (C and C) to minimize clock
skew and flight time mismatches
■ Echo clocks (CQ and CQ) simplify data capture in high-speed
systems
■ Synchronous internally self-timed writes
■ DDR II operates with 1.5-cycle read latency when DOFF is
asserted high
Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs (Q, sharing the same
physical pins as the data inputs D) are tightly matched to the two
output echo clocks CQ/CQ, eliminating the need for separately
capturing data from each individual DDR SRAM in the system
design. Output data clocks (C/C) enable maximum system
clocking and data synchronization flexibility.
■ Operates similar to DDR I device with one cycle read latency
when DOFF is asserted low
■ 1.8-V core power supply with high-speed transceiver logic
(HSTL) inputs and outputs
■ Variable drive HSTL output buffers
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
■ Expanded HSTL output voltage (1.4 V–VDD
❐ Supports both 1.5-V and 1.8-V I/O supply
)
■ Available in 165-ball fine-pitch ball grid array (FBGA) package
(15 ×17 × 1.4 mm)
For a complete list of related documentation, click here.
■ Offered in Pb-free packages
■ JTAG 1149.1 compatible test access port
■ Phase locked loop (PLL) for accurate data placement
Selection Guide
Description
Maximum operating frequency
333 MHz
333
300 MHz
300
250 MHz
250
Unit
MHz
mA
Maximum operating current
× 18
× 36
650
610
Not Offered
660
790
Not Offered
Cypress Semiconductor Corporation
Document Number: 001-44274 Rev. *O
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 30, 2020
CY7C1618KV18/CY7C1620KV18
Logic Block Diagram – CY7C1618KV18
Burst
Logic
A0
Write
Reg
Write
Reg
23 22
A
A
(22:0)
Address
Register
(22:1)
18
LD
K
K
Output
R/W
CLK
Logic
Gen.
Control
C
C
DOFF
Read Data Reg.
36
18
CQ
CQ
V
REF
18
18
Reg.
Reg.
Reg.
Control
Logic
R/W
18
18
BWS
DQ
[1:0]
[17:0]
Logic Block Diagram – CY7C1620KV18
Burst
Logic
A0
Write
Reg
Write
Reg
22 21
A
A
(21:0)
Address
Register
(21:1)
36
LD
K
K
Output
Logic
Control
CLK
R/W
Gen.
C
C
DOFF
Read Data Reg.
72
36
CQ
CQ
V
REF
36
36
Reg.
Reg.
Reg.
Control
Logic
R/W
36
36
BWS
DQ
[3:0]
[35:0]
Document Number: 001-44274 Rev. *O
Page 2 of 32
CY7C1618KV18/CY7C1620KV18
Contents
Pin Configurations ...........................................................4
Pin Definitions ..................................................................5
Functional Overview ........................................................6
Read Operations .........................................................6
Write Operations .........................................................6
Byte Write Operations .................................................6
Single Clock Mode ......................................................7
DDR Operation ............................................................7
Depth Expansion .........................................................7
Programmable Impedance ..........................................7
Echo Clocks ................................................................7
PLL ..............................................................................7
Application Example ........................................................8
Truth Table ........................................................................9
Burst Address Table ........................................................9
Write Cycle Descriptions ...............................................10
Write Cycle Descriptions ...............................................11
IEEE 1149.1 Serial Boundary Scan (JTAG) ..................12
Disabling the JTAG Feature ......................................12
Test Access Port .......................................................12
Performing a TAP Reset ...........................................12
TAP Registers ...........................................................12
TAP Instruction Set ...................................................12
TAP Controller State Diagram .......................................14
TAP Controller Block Diagram ......................................15
TAP Electrical Characteristics ......................................15
TAP AC Switching Characteristics ...............................16
TAP Timing and Test Conditions ..................................17
Identification Register Definitions ................................18
Scan Register Sizes .......................................................18
Instruction Codes ...........................................................18
Boundary Scan Order ....................................................19
Power Up Sequence in DDR II SRAM ...........................20
Power Up Sequence .................................................20
PLL Constraints .........................................................20
Maximum Ratings ...........................................................21
Operating Range .............................................................21
Neutron Soft Error Immunity .........................................21
Electrical Characteristics ...............................................21
DC Electrical Characteristics .....................................21
AC Electrical Characteristics ........................................23
Capacitance ....................................................................23
Thermal Resistance ........................................................23
AC Test Loads and Waveforms .....................................23
Switching Characteristics ..............................................24
Switching Waveforms ....................................................26
Read/Write/Deselect Sequence ................................26
Ordering Information ......................................................27
Ordering Code Definitions .........................................27
Package Diagram ............................................................28
Acronyms ........................................................................29
Document Conventions .................................................29
Units of Measure .......................................................29
Document History Page .................................................30
Sales, Solutions and Legal Information .......................32
Worldwide Sales and Design Support .......................32
Products ....................................................................32
PSoC® Solutions ......................................................32
Cypress Developer Community .................................32
Technical Support .....................................................32
Document Number: 001-44274 Rev. *O
Page 3 of 32
CY7C1618KV18/CY7C1620KV18
Pin Configurations
The pin configuration for CY7C1618KV18, and CY7C1620KV18 follow: [1]
Figure 1. 165-ball FBGA (15 × 17 × 1.4 mm) pinout
CY7C1618KV18 (8M × 18)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
A
3
4
5
BWS1
NC/288M
A
6
7
A
8
9
A
10
A
11
CQ
A
B
C
D
E
F
A
R/W
A
K
LD
DQ9
NC
NC
K
BWS0
A
A
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
A
NC
DQ8
NC
NC
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
A0
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
DQ7
NC
NC
DQ10
DQ11
NC
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
NC
NC
NC
DQ6
DQ5
NC
DQ12
NC
NC
G
H
J
DQ13
VDDQ
NC
NC
VREF
NC
VREF
DQ4
NC
ZQ
NC
K
L
NC
DQ14
NC
DQ3
DQ2
NC
DQ15
NC
NC
M
N
P
R
NC
DQ1
NC
NC
DQ16
DQ17
A
NC
NC
A
C
A
NC
DQ0
TDI
TCK
A
A
C
A
A
TMS
CY7C1620KV18 (4M × 36)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
3
4
5
BWS2
BWS3
A
6
7
BWS1
BWS0
A
8
9
A
10
A
11
A
B
C
D
E
F
A
A
R/W
A
K
LD
CQ
DQ27
NC
DQ18
DQ28
DQ19
DQ20
DQ21
DQ22
VDDQ
DQ32
DQ23
DQ24
DQ34
DQ25
DQ26
A
K
A
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
A
NC
DQ8
DQ7
DQ16
DQ6
DQ5
DQ14
ZQ
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
A0
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
DQ17
NC
DQ29
NC
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
DQ15
NC
DQ30
DQ31
VREF
NC
G
H
J
NC
VREF
DQ13
DQ12
NC
DQ4
DQ3
DQ2
DQ1
DQ10
DQ0
TDI
K
L
NC
DQ33
NC
M
N
P
R
DQ11
NC
DQ35
NC
A
C
A
DQ9
TMS
TCK
A
A
C
A
A
Note
1. NC/288M is not connected to the die and can be tied to any voltage level.
Document Number: 001-44274 Rev. *O
Page 4 of 32
CY7C1618KV18/CY7C1620KV18
Pin Definitions
Pin Name
I/O
Pin Description
DQ[x:0]
Input Output- Data input output signals: Inputs are sampled on the rising edge of K and K clocks during valid write
Synchronous operations. These pins drive out the requested data when the read operation is active. Valid data is
driven out on the rising edge of both the C and C clocks during read operations or K and K when in single
clock mode. When read access is deselected, Q[x:0] are automatically tristated.
CY7C1618KV18 − DQ[17:0]
CY7C1620KV18 − DQ[35:0]
LD
Input-
Synchronous load: This input is brought low when a bus cycle sequence is defined. This definition
Synchronous includes address and read and write direction. All transactions operate on a burst of 2 data.
BWS0,
BWS1,
BWS2,
BWS3
Input-
Byte write select (BWS) 0, 1, 2, and 3 − Active low: Sampled on the rising edge of the K and K clocks
Synchronous during write operations. Used to select which byte is written into the device during the current portion of
the write operations. Bytes not written remain unaltered.
CY7C1618KV18 − BWS0 controls D[8:0] and BWS1 controls D[17:9].
CY7C1620KV18 − BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18] and BWS3
controls D[35:27]
.
All the byte write selects are sampled on the same edge as the data. Deselecting a BWS ignores the
corresponding byte of data and it is not written into the device.
A, A0
Input-
Address inputs: These address inputs are multiplexed for both read and write operations. Internally,
Synchronous the device is organized as 8M × 18 (2 arrays each of 4M × 18) for CY7C1618KV18, and 4M × 36 (2
arrays each of 2M × 36) for CY7C1620KV18.
CY7C1618KV18 – A0 is the input to the burst counter. These are incremented in a linear fashion
internally. 23 address inputs are needed to access the entire memory array.
CY7C1620KV18 – A0 is the input to the burst counter. These are incremented in a linear fashion
internally. 22 address inputs are needed to access the entire memory array. All the address inputs are
ignored when the appropriate port is deselected.
R/W
C
Input-
Synchronous read or write input: When LD is low, this input designates the access type (read when
Synchronous R/W is high, write when R/W is low) for loaded address. R/W must meet the setup and hold times around
edge of K.
Input Clock Positive input clock for output data: C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board
back to the controller. See application example for further details.
C
Input Clock Negative input clock for output data: C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board
back to the controller. See application example for further details.
K
Input Clock Positive input clock input: The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising
edge of K.
Input Clock Negative input clock input: K is used to capture synchronous data being presented to the device and
K
to drive out data through Q[x:0] when in single clock mode.
CQ
Output Clock CQ referenced with respect to C: This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR II. In the single clock mode, CQ is generated with respect to K. The timing
for the echo clocks is shown in the AC Timing table.
Output Clock CQ referenced with respect to C: This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR II. In the single clock mode, CQ is generated with respect to K. The timing
for the echo clocks is shown in the AC Timing table.
CQ
ZQ
Input
Output impedance matching input: This input is used to tune the device outputs to the system data
bus impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 × RQ, where RQ is a resistor
connected between ZQ and ground. Alternatively, this pin can be connected directly to VDDQ, which
enables the minimum impedance mode. This pin cannot be connected directly to GND or left
unconnected.
Document Number: 001-44274 Rev. *O
Page 5 of 32
CY7C1618KV18/CY7C1620KV18
Pin Definitions (continued)
Pin Name
I/O
Pin Description
DOFF
Input
PLL turn Off − Active low. Connecting this pin to ground turns off the PLL inside the device. The timing
in the PLL turned off operation differs from those listed in this data sheet. For normal operation, this pin
can be connected to a pull-up through a 10 kΩ or less pull-up resistor. The device behaves in DDR I
mode when the PLL is turned off. In this mode, the device can be operated at a frequency of up to
167 MHz with DDR I timing.
TDO
TCK
Output
Input
Input
Input
N/A
Test data-out (TDO) pin for JTAG.
Test clock (TCK) pin for JTAG.
TDI
Test data-in (TDI) pin for JTAG.
TMS
NC
Test mode select (TMS) pin for JTAG.
Not connected to the die: Can be tied to any voltage level.
Not connected to the die: Can be tied to any voltage level.
Reference voltage input: Static input used to set the reference level for HSTL inputs, outputs, and AC
NC/288M
VREF
Input
Input-
Reference measurement points.
VDD
VSS
Power Supply Power supply inputs to the core of the device.
Ground
Ground for the device.
VDDQ
Power Supply Power supply inputs for the outputs of the device.
from the address location generated by the burst counter is
driven onto the Q[17:0]. The requested data is valid 0.45 ns from
the rising edge of the output clock (C or C, or K and K when in
single clock mode). To maintain the internal logic, each read
access must be enabled to complete. Read accesses can be
initiated on every rising edge of the positive input clock (K).
Functional Overview
The CY7C1618KV18, and CY7C1620KV18 are synchronous
pipelined burst SRAMs equipped with a DDR interface, which
operates with a read latency of one and a half cycles when DOFF
pin is tied high. When DOFF pin is set low or connected to VSS,
the device behaves in DDR I mode with a read latency of one
clock cycle.
When read access is deselected, the CY7C1618KV18 first
completes the pending read transactions. Synchronous internal
circuitry automatically tristates the output, following the next
rising edge of the positive output clock (C). This enables a
transition between devices without the insertion of wait states in
a depth expanded memory.
Accesses are initiated on the rising edge of the positive input
clock (K). All synchronous input timing is referenced from the
rising edge of the input clocks (K and K) and all output timing is
referenced to the rising edge of the output clocks (C/C, or K/K
when in single clock mode).
Write Operations
All synchronous data inputs (D[x:0]) pass through input registers
controlled by the rising edge of the input clocks (K and K). All
synchronous data outputs (Q[x:0]) pass through output registers
controlled by the rising edge of the output clocks (C/C, or K/K
when in single clock mode).
Write operations are initiated by asserting R/W low and LD low
at the rising edge of the positive input clock (K). The address
presented to address inputs is stored in the write address
register and the least significant bit of the address is presented
to the burst counter. The burst counter increments the address
in a linear fashion. On the following K clock rise, the data
presented to D[17:0] is latched and stored into the 18-bit write
data register, provided BWS[1:0] are both asserted active. On the
subsequent rising edge of the Negative Input Clock (K) the
information presented to D[17:0] is also stored into the write data
register, provided BWS[1:0] are both asserted active. The 36 bits
of data are then written into the memory array at the specified
location. Write accesses can be initiated on every rising edge of
the positive input clock (K). This pipelines the data flow so that
18 bits of data can be transferred into the device on every rising
edge of the input clocks (K and K).
All synchronous control (R/W, LD, BWS[0:X]) inputs pass through
input registers controlled by the rising edge of the input clock (K).
CY7C1618KV18 is described in the following sections. The
same basic descriptions apply to CY7C1620KV18.
Read Operations
The CY7C1618KV18 is organized internally as two arrays of
2M × 18. Accesses are completed in a burst of 2 sequential
18-bit data words. Read operations are initiated by asserting
R/W high and LD low at the rising edge of the positive input clock
(K). The address presented to address inputs is stored in the
read address register and the least significant bit of the address
is presented to the burst counter. The burst counter increments
the address in a linear fashion. Following the next K clock rise,
the corresponding 18-bit word of data from this address location
is driven onto the Q[17:0] using C as the output timing reference.
On the subsequent rising edge of C, the next 18-bit data word
When the write access is deselected, the device ignores all
inputs after the pending write operations have been completed.
Byte Write Operations
Byte write operations are supported by the CY7C1618KV18. A
write operation is initiated as described in Write Operations on
Document Number: 001-44274 Rev. *O
Page 6 of 32
CY7C1618KV18/CY7C1620KV18
page 6. The bytes that are written are determined by BWS0 and
BWS1, which are sampled with each set of 18-bit data words.
Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented, and writes it
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
for that byte to remain unaltered. This feature can be used to
simplify read, modify, or write operations to a byte write
operation.
Depth Expansion
Depth expansion requires replicating the LD control signal for
each bank. All other control signals can be common between
banks as appropriate.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and VSS to enable the SRAM to adjust its output
driver impedance. The value of RQ must be 5 × the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15 percent is between 175 Ω and 350 Ω, with VDDQ = 1.5 V.
The output impedance is adjusted every 1024 cycles upon power
up to account for drifts in supply voltage and temperature.
Single Clock Mode
The CY7C1618KV18 can be used with a single clock that
controls both the input and output registers. In this mode, the
device recognizes only a single pair of input clocks (K and K) that
control both the input and output registers. This operation is
identical to the operation if the device had zero skew between
the K/K and C/C clocks. All timing parameters remain the same
in this mode. To use this mode of operation, the user must tie C
and C high at power on. This function is a strap option and not
alterable during device operation.
Echo Clocks
Echo clocks are provided on the DDR II to simplify data capture
on high-speed systems. Two echo clocks are generated by the
DDR II. CQ is referenced with respect to C and CQ is referenced
with respect to C. These are free-running clocks and are
synchronized to the output clock of the DDR II. In single clock
mode, CQ is generated with respect to K and CQ is generated
with respect to K. The timing for the echo clocks is shown in the
Switching Characteristics on page 24.
DDR Operation
The CY7C1618KV18 enables high performance operation
through high clock frequencies (achieved through pipelining) and
DDR mode of operation. The CY7C1618KV18 requires a single
No Operation (NOP) cycle during transition from a read to a write
cycle. At higher frequencies, some applications may require a
second NOP cycle to avoid contention.
PLL
These chips use a PLL that is designed to function between
120 MHz and the specified maximum clock frequency. During
power up, when the DOFF is tied high, the PLL is locked after
20 μs of stable clock. The PLL can also be reset by slowing or
stopping the input clock K and K for a minimum of 30 ns.
However, it is not necessary to reset the PLL to lock to the
desired frequency. The PLL automatically locks 20 μs after a
stable clock is presented. The PLL may be disabled by applying
ground to the DOFF pin. When the PLL is turned off, the device
behaves in DDR I mode (with one cycle latency and a longer
access time).
If a read occurs after a write cycle, address and data for the write
are stored in registers. The write information must be stored
because the SRAM cannot perform the last word write to the
array, without conflicting with the read. The data stays in this
register until the next write cycle occurs. On the first write cycle
after the read(s), the stored data from the earlier write is written
into the SRAM array. This is called a posted write.
If a read is performed on the same address on which a write is
performed in the previous cycle, the SRAM reads out the most
current data. The SRAM does this by bypassing the memory
array and reading the data from the registers.
Document Number: 001-44274 Rev. *O
Page 7 of 32
CY7C1618KV18/CY7C1620KV18
Application Example
Figure 2 shows two DDR II used in an application.
Figure 2. Application Example (Width Expansion)
ZQ
ZQ
SRAM#1
DQ[x:0]
SRAM#2
CQ/CQ
CQ/CQ
RQ
RQ
DQ[x:0]
A
LD R/W BWS C C K K
A LD R/W BWS C C K K
DQ[2x:0]
ADDRESS
LD
R/W
BWS
CLKIN1/CLKIN1
CLKIN2/CLKIN2
SOURCE K
SOURCE K
DELAYED K
DELAYED K
FPGA / ASIC
Document Number: 001-44274 Rev. *O
Page 8 of 32
CY7C1618KV18/CY7C1620KV18
Truth Table
The truth table for the CY7C1618KV18, and CY7C1620KV18 follow: [2, 3, 4, 5, 6, 7]
Operation
K
LD
R/W
DQ
DQ
Write cycle:
Load address; wait one cycle;
L–H
L
L
D(A1) at K(t + 1) ↑ D(A2) at K(t + 1) ↑
input write data on consecutive K and K rising edges.
Read cycle:
L–H
L
H
Q(A1) at C(t + 1)↑ Q(A2) at C(t + 2) ↑
Load address; wait one and a half cycle;
read data on consecutive C and C rising edges.
NOP: No operation
L–H
H
X
X
X
High Z
High Z
Standby: Clock stopped
Stopped
Previous state
Previous state
Burst Address Table
(CY7C1618KV18, CY7C1620KV18)
First Address (External)
Second Address (Internal)
X..X0
X..X1
X..X1
X..X0
Notes
2. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
3. Device powers up deselected with the outputs in a tristate condition.
4. On CY7C1618KV18 and CY7C1620KV18, “A1” represents address location latched by the devices when transaction was initiated and “A2” represents the addresses
sequence in the burst.
5. “t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. Ensure that when clock is stopped K = K and C = C = high. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically.
Document Number: 001-44274 Rev. *O
Page 9 of 32
CY7C1618KV18/CY7C1620KV18
Write Cycle Descriptions
The write cycle description table for CY7C1618KV18 follows: [8, 9]
BWS0 BWS1
K
Comments
K
L
L
L–H
–
During the data portion of a write sequence:
CY7C1618KV18 − both bytes (D[17:0]) are written into the device.
L
L
–
L–H
–
L–H During the data portion of a write sequence:
CY7C1618KV18 − both bytes (D[17:0]) are written into the device.
L
H
H
L
–
During the data portion of a write sequence:
CY7C1618KV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L
L–H During the data portion of a write sequence:
CY7C1618KV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
H
H
L–H
–
–
During the data portion of a write sequence:
CY7C1618KV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
L
L–H During the data portion of a write sequence:
CY7C1618KV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H
H
H
H
L–H
–
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
Notes
8. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
9. Is based on a write cycle that was initiated in accordance with the Truth Table on page 9. BWS , BWS , BWS , and BWS can be altered on different portions of a
0
1
2
3
write cycle, as long as the setup and hold requirements are achieved.
Document Number: 001-44274 Rev. *O
Page 10 of 32
CY7C1618KV18/CY7C1620KV18
Write Cycle Descriptions
The write cycle description table for CY7C1620KV18 follows: [10, 11]
BWS0 BWS1 BWS2 BWS3
K
K
Comments
L
L
L
L
L–H
–
During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
L
L
L
–
L–H
–
L–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
H
H
L
H
H
H
H
L
H
H
H
H
H
H
L
–
During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
L
L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
H
H
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[17:9]) is written into the
device. D[8:0] and D[35:18] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into the
device. D[8:0] and D[35:18] remains unaltered.
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
H
H
H
H
H
H
H
H
L–H
–
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Notes
10. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
11. Is based on a write cycle that was initiated in accordance with the Truth Table on page 9. BWS , BWS , BWS , and BWS can be altered on different portions of a
0
1
2
3
write cycle, as long as the setup and hold requirements are achieved.
Document Number: 001-44274 Rev. *O
Page 11 of 32
CY7C1618KV18/CY7C1620KV18
Instruction Register
IEEE 1149.1 Serial Boundary Scan (JTAG)
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins, as shown in TAP Controller Block Diagram on
page 15. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
These SRAMs incorporate a serial boundary scan Test Access
Port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard 1149.1-2001. The TAP operates using JEDEC
standard 1.8 V I/O logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied low
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternatively be connected to VDD through a pull-up resistor. TDO
must be left unconnected. Upon power up, the device comes up
in a reset state, which does not interfere with the operation of the
device.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to enable fault
isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, you
can skip certain chips. The bypass register is a single-bit register
that is placed between TDI and TDO pins. This enables shifting
of data through the SRAM with minimal delay. The bypass
register is set low (VSS) when the BYPASS instruction is
executed.
Test Access Port
Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Boundary Scan Register
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several No Connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The pin is pulled up
internally, resulting in a Logic HIGH level.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can
be used to capture the contents of the input and output ring.
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
instruction loaded into the TAP instruction register, chooses the
register between TDI and TDO. For information about loading
the instruction register, see the TAP Controller State Diagram on
page 14. TDI is internally pulled up and can be unconnected if
the TAP is unused in an application. TDI is connected to the most
significant bit (MSB) on any register.
The Boundary Scan Order on page 19 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in Identification Register Definitions on
page 18.
Test Data-Out (TDO)
The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
of the TAP state machine (see Instruction Codes on page 18).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
TAP Instruction Set
Performing a TAP Reset
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction
Codes on page 18. Three of these instructions are listed as
RESERVED and cannot be used. The other five instructions are
described in this section in detail.
A Reset is performed by forcing TMS high (VDD) for five rising
edges of TCK. This Reset does not affect the operation of the
SRAM and can be performed while the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a High Z state.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller is moved
into the Update-IR state.
TAP Registers
Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.
Document Number: 001-44274 Rev. *O
Page 12 of 32
CY7C1618KV18/CY7C1620KV18
IDCODE
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.
The shifting of data for the SAMPLE and PRELOAD phases
occurs concurrently when required, that is, while the data
captured is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High Z state until the next command is supplied during the
Update IR state.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
EXTEST OUTPUT BUS TRISTATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tristate mode.
The TAP controller clock only operates at a frequency up to
20 MHz, while the SRAM clock operates more than an order of
magnitude faster. Since there is a large difference in the clock
frequencies, it is possible that during the Capture-DR state, an
input or output undergoes a transition. The TAP may then try to
capture a signal while in transition (metastable state). This does
not harm the device, but there is no guarantee to the value that
is captured. Repeatable results may not be possible.
The boundary scan register has a special bit located at bit 108.
When this scan cell, called the ‘extest output bus tristate’, is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When high, it enables the output buffers to drive the
output bus. When low, this bit places the output bus into a High Z
condition.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if the design does not stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
possible to capture all other signals and simply ignore the value
of the CK and CK captured in the boundary scan register.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the Shift-DR state. During Update-DR, the value loaded
into that shift-register cell latches into the preload register. When
the EXTEST instruction is entered, this bit directly controls the
output Q-bus pins. Note that this bit is preset high to enable the
output when the device is powered up, and also when the TAP
controller is in the Test-Logic-Reset state.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Document Number: 001-44274 Rev. *O
Page 13 of 32
CY7C1618KV18/CY7C1620KV18
TAP Controller State Diagram
The state diagram for the TAP controller follows. [12]
TEST-LOGIC
1
RESET
0
1
1
1
SELECT
TEST-LOGIC/
SELECT
0
IR-SCAN
IDLE
DR-SCAN
0
0
1
1
CAPTURE-DR
0
CAPTURE-IR
0
0
1
0
1
SHIFT-DR
1
SHIFT-IR
1
EXIT1-DR
0
EXIT1-IR
0
0
0
PAUSE-DR
1
PAUSE-IR
1
0
0
EXIT2-DR
1
EXIT2-IR
1
UPDATE-IR
0
UPDATE-DR
1
1
0
Note
12. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document Number: 001-44274 Rev. *O
Page 14 of 32
CY7C1618KV18/CY7C1620KV18
TAP Controller Block Diagram
0
Bypass Register
2
1
1
1
0
0
0
Selection
TDI
Selection
Circuitry
TDO
Instruction Register
Circuitry
31 30
29
.
.
2
Identification Register
.
108
.
.
.
2
Boundary Scan Register
TCK
TMS
TAP Controller
TAP Electrical Characteristics
Over the Operating Range
Parameter [13, 14, 15]
Description
Output high voltage
Output high voltage
Output low voltage
Output low voltage
Input high voltage
Input low voltage
Test Conditions
IOH = −2.0 mA
Min
1.4
1.6
–
Max
–
Unit
V
VOH1
VOH2
VOL1
VOL2
VIH
IOH = −100 μA
IOL = 2.0 mA
IOL = 100 μA
–
–
V
0.4
0.2
V
–
V
0.65 × VDD VDD + 0.3
V
VIL
–
–0.3
–5
0.35 × VDD
5
V
IX
Input and output load current
GND ≤ VI ≤ VDD
μA
Notes
13. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics on page 21.
14. Overshoot: V < V + 0.85 V (Pulse width less than t /2), Undershoot: V /2).
> -1.5 V (Pulse width less than t
CYC
IH(AC)
DDQ
CYC
IL(AC)
15. All voltage referenced to ground.
Document Number: 001-44274 Rev. *O
Page 15 of 32
CY7C1618KV18/CY7C1620KV18
TAP AC Switching Characteristics
Over the Operating Range
Parameter [16, 17]
Description
Min
50
–
Max
–
Unit
ns
tTCYC
TCK clock cycle time
TCK clock frequency
TCK clock high
tTF
20
–
MHz
ns
tTH
20
20
tTL
TCK clock low
–
ns
Setup Times
tTMSS
tTDIS
TMS setup to TCK clock rise
TDI setup to TCK clock rise
Capture setup to TCK rise
5
5
5
–
–
–
ns
ns
ns
tCS
Hold Times
tTMSH
tTDIH
TMS hold after TCK clock rise
TDI hold after clock rise
5
5
5
–
–
–
ns
ns
ns
tCH
Capture hold after clock rise
Output Times
tTDOV
tTDOX
TCK clock low to TDO valid
TCK clock low to TDO invalid
–
0
10
–
ns
ns
Notes
16. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS
CH
17. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document Number: 001-44274 Rev. *O
Page 16 of 32
CY7C1618KV18/CY7C1620KV18
TAP Timing and Test Conditions
Figure 3 shows the TAP timing and test conditions. [18]
Figure 3. TAP Timing and Test Conditions
0.9 V
50
ALL INPUT PULSES
1.8 V
0.9 V
Ω
TDO
0 V
Z = 50
Ω
0
C = 20 pF
L
t
t
TL
TH
GND
(a)
Test Clock
TCK
t
TCYC
t
TMSH
t
TMSS
Test Mode Select
TMS
t
TDIS
t
TDIH
Test Data In
TDI
Test Data Out
TDO
t
TDOV
t
TDOX
Note
18. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document Number: 001-44274 Rev. *O
Page 17 of 32
CY7C1618KV18/CY7C1620KV18
Identification Register Definitions
Value
Instruction Field
Description
CY7C1618KV18
CY7C1620KV18
000
Revision number (31:29)
Cypress device ID (28:12)
Cypress JEDEC ID (11:1)
000
Version number.
11010100010010011
00000110100
11010100010100011
00000110100
Defines the type of SRAM.
Allows unique identification of
SRAM vendor.
ID register presence (0)
1
1
Indicates the presence of an ID
register.
Scan Register Sizes
Register Name
Bit Size
Instruction
Bypass
3
1
ID
32
109
Boundary Scan
Instruction Codes
Instruction
EXTEST
Code
000
Description
Captures the input and output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input and output contents. Places the boundary scan register between TDI and
TDO. Forces all SRAM output drivers to a High Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures the input and output ring contents. Places the boundary scan register between TDI
and TDO. Does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operation.
Document Number: 001-44274 Rev. *O
Page 18 of 32
CY7C1618KV18/CY7C1620KV18
Boundary Scan Order
Bit No.
0
Bump ID
6R
Bit No.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Bump ID
10G
9G
Bit No.
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
Bump ID
6A
Bit No.
84
Bump ID
1J
1
6P
5B
85
2J
2
6N
11F
11G
9F
5A
86
3K
3
7P
4A
87
3J
4
7N
5C
4B
88
2K
5
7R
10F
11E
10E
10D
9E
89
1K
6
8R
3A
90
2L
7
8P
2A
91
3L
8
9R
1A
92
1M
1L
9
11P
10P
10N
9P
2B
93
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10C
11D
9C
3B
94
3N
1C
1B
95
3M
1N
96
10M
11N
9M
9D
3D
3C
1D
2C
3E
97
2M
3P
11B
11C
9B
98
99
2N
9N
100
101
102
103
104
105
106
107
108
2P
11L
11M
9L
10B
11A
10A
9A
1P
2D
2E
3R
4R
10L
11K
10K
9J
1E
4P
8B
2F
5P
7C
3F
5N
6C
1G
1F
5R
9K
8A
Internal
10J
11J
11H
7A
3G
2G
1H
7B
6B
Document Number: 001-44274 Rev. *O
Page 19 of 32
CY7C1618KV18/CY7C1620KV18
PLL Constraints
Power Up Sequence in DDR II SRAM
■ PLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as tKC Var
DDR II SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.
.
■ The PLL functions at frequencies down to 120 MHz.
Power Up Sequence
■ If the input clock is unstable and the PLL is enabled, then the
PLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide 20 μs of stable clock to
relock to the desired clock frequency.
■ Apply power and drive DOFF either high or low (all other inputs
can be high or low).
❐ Apply VDD before VDDQ
.
❐ Apply VDDQ before VREF or at the same time as VREF
.
❐ Drive DOFF high.
■ Provide stable DOFF (high), power and clock (K, K) for 20 μs
to lock the PLL
Figure 4. Power Up Waveforms
K
K
Unstable Clock
> 20μs Stable clock
Stable)
DDQ
Start Normal
Operation
/
V
Clock Start (Clock Starts after V
DD
Stable (< +/- 0.1V DC per 50ns )
/
/
V
VDDQ
V
VDD
DD
DDQ
Fix HIGH (or tie to V
)
DDQ
DOFF
Document Number: 001-44274 Rev. *O
Page 20 of 32
CY7C1618KV18/CY7C1620KV18
Maximum Ratings
Operating Range
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Ambient
[20]
[20]
Range
Commercial
Industrial
Temperature (TA)
VDD
VDDQ
Storage temperature ................................ –65 °C to +150 °C
0 °C to +70 °C
1.8 ± 0.1 V 1.4 V to
VDD
Ambient temperature
with power applied ................................... –55 °C to +125 °C
–40 °C to +85 °C
Supply voltage on VDD relative to GND .......–0.5 V to +2.9 V
Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD
DC applied to outputs in High Z ........–0.5 V to VDDQ + 0.3 V
DC input voltage [19] ...........................–0.5 V to VDD + 0.3 V
Current into outputs (Low) .......................................... 20 mA
Neutron Soft Error Immunity
Test
Parameter Description
Conditions
Typ Max* Unit
LSBU
LMBU
SEL
Logical
single-bit
upsets
25 °C
25 °C
85 °C
197 216
FIT/
Mb
Static discharge voltage
(MIL-STD-883, M. 3015) .........................................> 2001 V
Latch up current .....................................................> 200 mA
Logical
multi-bit
upsets
0
0
0.01 FIT/
Mb
Single event
latch up
0.1
FIT/
Dev
* No LMBU or SEL events occurred during testing; this column represents a
2
statistical χ , 95% confidence limit calculation. For more details refer toApplication
Note Accelerated Neutron SER Testing and Calculation of Terrestrial Failure
Rates – AN54908.
Electrical Characteristics
Over the Operating Range
DC Electrical Characteristics
Over the Operating Range
Parameter [21]
VDD
Description
Power supply voltage
I/O supply voltage
Output high voltage
Output low voltage
Output high voltage
Output low voltage
Input high voltage
Input low voltage
Test Conditions
Min
1.7
Typ
1.8
1.5
–
Max
Unit
V
1.9
VDD
VDDQ
VOH
1.4
V
Note 22
Note 23
VDDQ/2 – 0.12
VDDQ/2 – 0.12
VDDQ – 0.2
VSS
VDDQ/2 + 0.12
VDDQ/2 + 0.12
VDDQ
V
VOL
–
V
VOH(LOW)
VOL(LOW)
VIH
IOH = −0.1 mA, Nominal impedance
–
V
IOL = 0.1 mA, Nominal impedance
–
0.2
V
VREF + 0.1
–0.3
–
VDDQ + 0.3
VREF – 0.1
5
V
VIL
–
V
IX
Input leakage current
GND ≤ VI ≤ VDDQ
−5
–
μA
μA
V
IOZ
Output leakage current
Input reference voltage [24] Typical Value = 0.75 V
GND ≤ VI ≤ VDDQ, Output disabled
−5
–
5
VREF
0.68
0.75
0.95
Notes
19. Overshoot: V
20. Power up: assumes a linear ramp from 0 V to V
< V
+ 0.85 V (Pulse width less than t
/2), Undershoot: V
> −1.5 V (Pulse width less than t
/2).
CYC
IH(AC)
DDQ
CYC
IL(AC)
within 200 ms. During this time V < V and V
< V
.
DD(min)
IH
DD
DDQ
DD
21. All voltage referenced to ground.
22. Outputs are impedance controlled. I = –(V
/2)/(RQ/5) for values of 175 Ω < RQ < 350 Ω.
/2)/(RQ/5) for values of 175 Ω < RQ < 350 Ω.
OH
DDQ
23. Outputs are impedance controlled. I = (V
OL
DDQ
24. V
= 0.68 V or 0.45 V
, whichever is larger, V
= 0.95 V or 0.54 V
, whichever is smaller.
DDQ
REF(min)
DDQ
REF(max)
Document Number: 001-44274 Rev. *O
Page 21 of 32
CY7C1618KV18/CY7C1620KV18
Electrical Characteristics (continued)
Over the Operating Range
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter [21]
Description
Test Conditions
Min
–
Typ
–
Max
650
790
610
660
410
410
390
370
Unit
[25]
IDD
VDD operating supply
VDD = Max, IOUT = 0 mA, 333 MHz (× 18)
f = fMAX = 1/tCYC
mA
(× 36)
–
–
300 MHz (× 18)
250 MHz (× 36)
–
–
mA
mA
mA
–
–
ISB1
Automatic Power Down
Current
Max VDD
,
333 MHz (× 18)
(× 36)
–
–
Both Ports Deselected,
–
–
VIN ≥ VIH or VIN ≤ VIL,
f = fMAX = 1/tCYC
Inputs Static
,
300 MHz (× 18)
250 MHz (× 36)
–
–
mA
mA
–
–
Note
25. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-44274 Rev. *O
Page 22 of 32
CY7C1618KV18/CY7C1620KV18
AC Electrical Characteristics
Over the Operating Range
Parameter [26]
Description
Input high voltage
Input low voltage
Test Conditions
Min
VREF + 0.2
–
Typ
–
Max
–
Unit
V
VIH
VIL
–
VREF – 0.2
V
Capacitance
Parameter [27]
Description
Input capacitance
Output capacitance
Test Conditions
Max
4
Unit
pF
CIN
CO
TA = 25 °C, f = 1 MHz, VDD = 1.8 V, VDDQ = 1.5 V
4
pF
Thermal Resistance
165-ballFBGA
Package
Parameter [27]
Description
Test Conditions
Unit
Θ
Θ
Θ
JA (0 m/s)
JA (1 m/s)
JA (3 m/s)
Thermal resistance
(junction to ambient)
Socketed on a 170 × 220 × 2.35 mm, eight-layer printed
circuit board
12.23
11.17
10.42
9.34
°C/W
°C/W
°C/W
°C/W
ΘJB
Thermal resistance
(junction to board)
ΘJC
Thermal resistance
(junction to case)
2.10
°C/W
AC Test Loads and Waveforms
Figure 5. AC Test Loads and Waveforms
VREF = 0.75 V
0.75 V
VREF
VREF
0.75 V
R = 50Ω
OUTPUT
[28]
ALL INPUT PULSES
1.25 V
Z = 50Ω
0
OUTPUT
Device
R = 50Ω
L
0.75 V
Under
Device
Under
0.25 V
Test
5 pF
VREF = 0.75 V
Slew Rate = 2 V/ns
ZQ
Test
ZQ
RQ =
RQ =
250Ω
250Ω
INCLUDING
JIG AND
(a)
(b)
SCOPE
Notes
26. Overshoot: V
< V
+ 0.85 V (Pulse width less than t
/2), Undershoot: V
> −1.5 V (Pulse width less than t
/2).
IH(AC)
DDQ
CYC
IL(AC)
CYC
27. Tested initially and after any design or process change that may affect these parameters.
28. Unless otherwise noted, test conditions assume signal transition time of 2 V/ns, timing reference levels of 0.75 V, V
= 0.75 V, RQ = 250 Ω, V
= 1.5 V, input
REF
DDQ
pulse levels of 0.25 V to 1.25 V, and output loading of the specified I /I and load capacitance shown in (a) of Figure 5.
OL OH
Document Number: 001-44274 Rev. *O
Page 23 of 32
CY7C1618KV18/CY7C1620KV18
Switching Characteristics
Over the Operating Range
Parameters [29, 30]
333 MHz
300 MHz
250 MHz
Description
Unit
Cypress Consortium
Parameter Parameter
Min
Max
Min
Max
Min
Max
tPOWER
tCYC
tKH
VDD(typical) to the first access [31]
K clock and C clock cycle time
Input clock (K/K; C/C) high
Input clock (K/K; C/C) low
1
–
8.4
–
1
–
8.4
–
1
–
8.4
–
ms
ns
ns
ns
ns
tKHKH
tKHKL
tKLKH
tKHKH
3.0
3.3
4.0
1.6
1.6
1.8
1.20
1.20
1.35
1.32
1.32
1.49
tKL
–
–
–
tKHKH
–
–
–
K clock rise to K clock rise and C
to C rise (rising edge to rising
edge)
tKHCH
tKHCH
0.0
1.30
0.0
1.45
0.0
1.8
ns
K/K clock rise to C/C clock rise
(rising edge to rising edge)
Setup Times
tSA tAVKH
tSC tIVKH
Address setup to K clock rise
0.4
0.4
–
–
0.4
0.4
–
–
0.5
0.5
–
–
ns
ns
ControlsetuptoKclockrise(RPS,
WPS)
tSCDDR
tIVKH
Double data rate control setup to
clock (K/K) rise (BWS0, BWS1,
BWS2, BWS3)
0.3
0.3
–
–
0.3
0.3
–
–
0.35
0.35
–
–
ns
ns
tSD
tDVKH
D[X:0] setup to clock (K/K) rise
Hold Times
tHA
tHC
tKHAX
tKHIX
0.4
0.4
–
–
0.4
0.4
–
–
0.5
0.5
–
–
ns
ns
Address hold after K clock rise
Control hold after K clock rise
(RPS, WPS)
tHCDDR
tHD
tKHIX
DDR control hold after clock (K/K)
rise (BWS0, BWS1, BWS2, BWS3)
0.3
0.3
–
–
0.3
0.3
–
–
0.35
0.35
–
–
ns
ns
tKHDX
D[X:0] hold after Clock (K/K) rise
Notes
29. Unless otherwise noted, test conditions assume signal transition time of 2 V/ns, timing reference levels of 0.75 V, V
= 0.75 V, RQ = 250 Ω, V
= 1.5 V, input pulse
REF
DDQ
levels of 0.25 V to 1.25 V, and output loading of the specified I /I and load capacitance shown in (a) of Figure 5 on page 23.
OL OH
30. When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being
operated and outputs data with the output timings of that frequency range.
31. This part has an internal voltage regulator; t
is the time that the power is supplied above V min initially before a read or write operation can be initiated.
DD
POWER
Document Number: 001-44274 Rev. *O
Page 24 of 32
CY7C1618KV18/CY7C1620KV18
Switching Characteristics (continued)
Over the Operating Range
Parameters [29, 30]
333 MHz
300 MHz
250 MHz
Description
Unit
Cypress Consortium
Parameter Parameter
Min
Max
Min
Max
Min
Max
Output Times
tCO
tCHQV
tCHQX
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
C/C clock rise (or K/K in single
clock mode) to data valid
tDOH
–0.45
–0.45
–0.45
Data output hold after output C/C
clock rise (active to active)
tCCQO
tCQOH
tCHCQV
tCHCQX
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
C/C clock rise to echo clock valid
–0.45
–0.45
–0.45
Echo clock hold after C/C clock
rise
tCQD
tCQHQV
tCQHQX
tCQHCQL
tCQHCQH
Echo clock high to data valid
Echo clock high to data invalid
Output clock (CQ/CQ) high [32]
–
0.25
–
0.27
–
0.30
ns
ns
ns
ns
tCQDOH
tCQH
–0.25
1.25
1.25
–
–
–
–0.27
1.40
1.40
–
–
–
–0.30
1.75
1.75
–
–
–
tCQHCQH
CQ clock rise to CQ clock rise
(rising edge to rising edge) [32]
tCHZ
tCHQZ
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
Clock (C/C) rise to High Z (Active
to High Z) [33, 34]
Clock (C/C) rise to Low Z [33, 34]
tCLZ
tCHQX1
–0.45
–0.45
–0.45
PLL Timing
tKC Var
tKC Var
Clock phase jitter
–
0.20
–
–
0.20
–
–
0.20
–
ns
μs
ns
tKC lock
tKC lock
tKC Reset
PLL lock time (K, C)
K static to PLL reset
20
30
20
30
20
30
tKC Reset
–
–
–
Notes
32. These parameters are extrapolated from the input timing parameters (t
design and are not tested in production.
/2 – 250 ps, where 250 ps is the internal jitter). These parameters are only guaranteed by
CYC
33. t
, t
are specified with a load capacitance of 5 pF as in (b) of Figure 5 on page 23. Transition is measured 100 mV from steady-state voltage.
CHZ CLZ
34. At any voltage and temperature t
is less than t
and t
less than t
.
CHZ
CLZ
CHZ
CO
Document Number: 001-44274 Rev. *O
Page 25 of 32
CY7C1618KV18/CY7C1620KV18
Switching Waveforms
Read/Write/Deselect Sequence
Figure 6. Read/Write/Deselect Sequence [35, 36, 37]
Notes
35. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0 + 1.
36. Outputs are disabled (High Z) one clock cycle after a NOP.
37. In this example, if address A4 = A3, then data Q40 = D30 and Q41 = D31. Write data is forwarded immediately as read results. This note applies to the whole diagram.
Document Number: 001-44274 Rev. *O
Page 26 of 32
CY7C1618KV18/CY7C1620KV18
Ordering Information
The following table contains only the parts that are currently available. If you do not see what you are looking for, contact your local
sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products.
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
250 CY7C1620KV18-250BZXC
300 CY7C1618KV18-300BZXC
333 CY7C1618KV18-333BZXC
CY7C1620KV18-333BZXI
51-85195 165-ball FBGA (15 × 17 × 1.4 mm) Pb-free
51-85195 165-ball FBGA (15 × 17 × 1.4 mm) Pb-free
51-85195 165-ball FBGA (15 × 17 × 1.4 mm) Pb-free
Commercial
Commercial
Commercial
Industrial
Ordering Code Definitions
CY
7
C 16XX
K V18 -
XXX
X
X
BZ
Temperature Grade: X = C or I
C = Commercial; I = Industrial
Pb-free
Package Type: BZ = 165-ball FBGA
Frequency Range: XXX = 300 MHz or 333 MHz or 250MHz
V18 = 1.8 V
Die Revision
Part Identifier: 16XX = 1618 or 1620
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 001-44274 Rev. *O
Page 27 of 32
CY7C1618KV18/CY7C1620KV18
Package Diagram
Figure 7. 165-ball FBGA (15 × 17 × 1.40 mm (0.50 Ball Diameter)) Package Outline, 51-85195
51-85195 *E
Document Number: 001-44274 Rev. *O
Page 28 of 32
CY7C1618KV18/CY7C1620KV18
Acronyms
Document Conventions
Units of Measure
Symbol
Acronym
Description
BWS
DDR
DLL
Byte Write Select
Unit of Measure
Double Data Rate
Delay Lock Loop
°C
degree Celsius
failure in time per device
FIT/Dev
FIT/Mb
MHz
µA
failure in time per mega bit
megahertz
microampere
microsecond
milliampere
millimeter
millisecond
nanosecond
ohm
FBGA
HSTL
I/O
Fine-Pitch Ball Grid Array
High-Speed Transceiver Logic
Input/Output
µs
JTAG
LSB
Joint Test Action Group
Least Significant Bit
Logical Single-Bit Upsets
Logical Multi-Bit Upsets
Most Significant Bit
Phase Locked Loop
Quad Data Rate
mA
mm
ms
LSBU
LMBU
MSB
PLL
ns
Ω
%
percent
QDR
SEL
pF
picofarad
Single Event Latch-up
Static Random Access Memory
Test Access Port
V
volt
SRAM
TAP
W
watt
TCK
TDI
Test Clock
Test Data-In
TDO
TMS
Test Data-Out
Test Mode Select
Document Number: 001-44274 Rev. *O
Page 29 of 32
CY7C1618KV18/CY7C1620KV18
Document History Page
Document Title: CY7C1618KV18/CY7C1620KV18, 144-Mbit DDR II SRAM Two-Word Burst Architecture
Document Number: 001-44274
Submission
Rev.
ECN No.
Description of Change
Date
**
1961327
2555945
See ECN New data sheet.
*A
08/22/08
Updated Identification Register Definitions (Changed Revision Number (31:29) from 001 to
000).
Updated Power Up Sequence in DDR II SRAM (description and Figure 4).
Updated Maximum Ratings (Changed Ambient Temperature with Power Applied from “–10
°C to +85 °C” to “–55 °C to +125 °C”).
Updated Electrical Characteristics (Updated DC Electrical Characteristics (Updated the
maximum values of IDD and ISB1 parameters)).
Updated Thermal Resistance (Included values for 165-ball FBGA package).
*B
2806011
11/12/09
Added Neutron Soft Error Immunity.
Updated Capacitance (Changed maximum value of Input capacitance (CIN) from 2 pF to 4
pF, changed maximum value of Output capacitance (CO) from 3 pF to 4 pF).
Updated Ordering Information (By including parts that are available) and added disclaimer
at the top of Ordering Information table.
Updated Package Diagram.
*C
*D
3022441
3243572
09/03/2010 Changed status from Preliminary to Final.
Updated Ordering Information (Updated part numbers) and added Ordering Code Defini-
tions.
Added Acronyms and Units of Measure.
Updated Sales, Solutions and Legal Information.
04/28/2011 Updated Ordering Information (Updated part numbers).
Updated to new template.
*E
*F
3275033
3430142
06/06/2011 No technical updates.
11/04/2011 Updated Ordering Information (Updated part numbers).
Updated Package Diagram.
*G
3565554
03/29/2012 Updated Features (Removed CY7C1616KV18, CY7C1627KV18 related information).
Updated Configuration (Removed CY7C1616KV18, CY7C1627KV18 related information).
Updated Functional Description (Removed CY7C1616KV18, CY7C1627KV18 related
information).
Updated Selection Guide (Removed 250 MHz, 200 MHz, and 167 MHz frequencies related
information).
Removed Logic Block Diagram – CY7C1616KV18.
Removed Logic Block Diagram – CY7C1627KV18.
Updated Pin Configurations (Removed CY7C1616KV18, CY7C1627KV18 related
information).
Updated Pin Definitions (Removed CY7C1616KV18, CY7C1627KV18 related information).
Updated Functional Overview (Removed CY7C1616KV18, CY7C1627KV18 related
information).
Updated Write Cycle Descriptions (Removed CY7C1616KV18 related information).
Removed Write Cycle Descriptions (corresponding to CY7C1627KV18).
Updated Identification Register Definitions (Removed CY7C1616KV18, CY7C1627KV18
related information).
Updated Electrical Characteristics (Updated DC Electrical Characteristics (Removed
CY7C1616KV18, CY7C1627KV18 related information, removed 250 MHz, 200 MHz, and
167 MHz frequencies related information, removed 300 MHz frequency related information
for only CY7C1620KV18)).
Updated Switching Characteristics (Removed 250 MHz, 200 MHz, and 167 MHz
frequencies related information).
Updated Ordering Information (Updated part numbers).
Document Number: 001-44274 Rev. *O
Page 30 of 32
CY7C1618KV18/CY7C1620KV18
Document History Page (continued)
Document Title: CY7C1618KV18/CY7C1620KV18, 144-Mbit DDR II SRAM Two-Word Burst Architecture
Document Number: 001-44274
Submission
Rev.
ECN No.
Description of Change
Date
*H
3702845
08/06/2012 Updated Selection Guide (Included 250 MHz frequency related information).
Updated Electrical Characteristics (Updated DC Electrical Characteristics (Included 250
MHz frequency related information)).
Updated Switching Characteristics (Included 250 MHz frequency related information).
Updated Ordering Information (Updated part numbers).
*I
3800880
4372963
11/02/2012 No technical updates.
Completing Sunset Review.
*J
05/07/2014 Updated Application Example:
Updated Figure 2.
Updated Thermal Resistance:
Updated values of ΘJA parameter.
Included ΘJB parameter and its details.
Updated to new template.
*K
*L
4575228
5072740
11/20/2014 Updated Functional Description:
Added “For a complete list of related documentation, click here.” at the end.
01/05/2016 Updated Package Diagram:
spec 51-85195 – Changed revision from *C to *D.
Updated to new template.
Completing Sunset Review.
*M
5131023
02/09/2016 Updated Switching Waveforms:
Updated Read/Write/Deselect Sequence:
Updated Figure 6.
*N
*O
5980689
6872794
11/30/2017 Updated logo and copyright.
04/30/2020 Updated Package Diagram:
spec 51-85195 – Changed revision from *D to *E.
Document Number: 001-44274 Rev. *O
Page 31 of 32
CY7C1618KV18/CY7C1620KV18
Sales, Solutions and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
®
Products
PSoC Solutions
ARM® Cortex® Microcontrollers
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/iot
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
Automotive
Cypress Developer Community
Clocks & Buffers
Interface
Community | Code Examples | Projects | Video | Blogs |
Training | Components
Internet of Things
Memory
Technical Support
cypress.com/memory
cypress.com/mcu
cypress.com/support
Microcontrollers
PSoC
cypress.com/psoc
cypress.com/pmic
cypress.com/touch
cypress.com/usb
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
cypress.com/wireless
© Cypress Semiconductor Corporation, 2008-2020. This document is the property of Cypress Semiconductor Corporation and its subsidiaries (“Cypress”). This document, including any software or
firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves
all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If
the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal,
non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software
solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through
resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified)
to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing
device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such
as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING
CYPRESS PRODUCTS, WILLBE FREE FROM CORRUPTION,ATTACK, VIRUSES, INTERFERENCE, HACKING, DATALOSS OR THEFT, OR OTHER SECURITYINTRUSION (collectively, “Security
Breach”). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In
addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted
by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or
circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility
of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. “High-Risk Device” means any
device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices.
“Critical Component” means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect
its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product
as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents, affiliates, distributors, and assigns harmless from and against all claims,
costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical
Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress's published
data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a
Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-44274 Rev. *O
Revised April 30, 2020
Page 32 of 32
相关型号:
©2020 ICPDF网 联系我们和版权申明