PEF3452HV1.3 [INFINEON]
PCM Transceiver, 1-Func, CMOS, PQFP44, 10 X 10 MM, 0.8 MM PITCH, METRIC, PLASTIC, QFP-44;
| 型号： | PEF3452HV1.3 |
| 厂家： | 
Infineon |
| 描述： | PCM Transceiver, 1-Func, CMOS, PQFP44, 10 X 10 MM, 0.8 MM PITCH, METRIC, PLASTIC, QFP-44 PC 电信 电信集成电路 |
| 文件： | 总71页 (文件大小：1093K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Preliminary Data Sheet, DS1, December 2001
TE3-LIU™
Line Interface Unit for
DS3, STS 1 and E3
PEF 3452 Version 1.3
Wired
Communications
N e v e r s t o p t h i n k i n g .
Edition 2001-12-05
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81669 München, Germany
© Infineon Technologies AG 2001.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address
list).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Preliminary Data Sheet, DS1, December 2001
TE3-LIU™
Line Interface Unit for
DS3, STS 1 and E3
PEF 3452 Version 1.3
Wired
Communications
N e v e r s t o p t h i n k i n g .
PEF 3452
PRELIMINARY
Revision History:
2001-12-05
DS1
Previous Version:
Preliminary Data Sheet TE3-LIU V1.2, 2001-07, DS3
Page
24
Subjects (major changes since last revision)
Chapter 4.1.4
27
Table 10
28
Figure 12
For questions on technology, delivery and prices please contact the Infineon
Technologies Offices in Germany or the Infineon Technologies Companies and
Representatives worldwide: see our webpage at http://www.infineon.com
PEF 3452
TE3-LIU V1.3
Table of Contents
Page
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
1.2
1.3
2
2.1
2.2
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hardware Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1
3.2
3.3
3.3.1
4
4.1
Interface Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Standard Receiver Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Line Monitoring Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Receive Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Receive Clock and Data Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Receive Line Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
AMI Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
B3ZS Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
HDB3 Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Alarm Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DS3 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
STS-1 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
E3 LOS Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Receive Output Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Transmit Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Transmit Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Jitter Attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Intrinsic Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Pulse Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Transmit Line Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AMI Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
B3ZS Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
HDB3 Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AIS Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Framer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Maintenance Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.5.1
4.1.5.2
4.1.5.3
4.1.6
4.1.6.1
4.1.6.2
4.1.6.3
4.1.7
4.1.8
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.6.1
4.2.6.2
4.2.6.3
4.2.7
4.3
4.4
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
Table of Contents
Page
4.4.1
4.4.2
Remote Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Local Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5
Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operational Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Device Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Transmit Line Inactive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.1
5.2
5.3
5.4
6
6.1
6.2
6.3
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Jitter Attenuator Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Microprocessor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Transmit Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Receive Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Pulse Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Pulse Template E3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Pulse Template DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Pulse Template STS-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Package Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Test Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4
6.4.1
6.4.2
6.4.3
6.4.4
6.4.5
6.4.6
6.4.7
6.4.7.1
6.4.7.2
6.4.7.3
6.5
6.6
6.7
7
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8
8.1
8.2
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Cable Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
List of Figures
Page
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
T3/T1 Multiplexer Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Channelized T3 Link Layer Application . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unchannelized T3 Link Layer Application . . . . . . . . . . . . . . . . . . . . . . . 5
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Receiver Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DS3 Line Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Receive Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
E3 Loss of Signal Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Jitter Tolerance Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Transmitter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Transmit Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Jitter Attenuation Characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Remote Loop Signal Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Local Loop Signal Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Reference Clock Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
XTAL Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Recommended Crystal Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Crystal Pulling Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chip Select Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
XCLK Input Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RCLK Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
E3 Pulse Shape at Transmitter Output . . . . . . . . . . . . . . . . . . . . . . . . 49
DS3 Pulse Shape at the Cross Connect Point (450 ft.) . . . . . . . . . . . . 50
STS-1 Pulse Shape at the Cross Connect Point (450 ft.) . . . . . . . . . . 52
Thermal Behavior of Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Input/Output Waveforms for AC Testing . . . . . . . . . . . . . . . . . . . . . . . 55
DS3 Cable Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
List of Tables
Page
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Interface Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Supply Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Test Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hardware Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hardware Indication Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
External Component Values for Receiver . . . . . . . . . . . . . . . . . . . . . . 21
External Component Values for DS Line Monitoring . . . . . . . . . . . . . . 22
E3 Receive Return Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Input Jitter Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
External Component Values for Transmitter . . . . . . . . . . . . . . . . . . . . 29
E3 Transmit Return Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Jitter Attenuation PLL Operation Frequencies . . . . . . . . . . . . . . . . . . . 31
Transmit Output Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Power Supply Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Reset Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
REFCLK Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
XTAL Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
XTAL Crystal Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chip Select Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . 46
XCLK Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RCLK Timing Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
E3 Pulse Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
DS3 Pulse Mask (ANSI T1.404, GR-499-CORE) . . . . . . . . . . . . . . . . 50
DS3 Pulse Mask (ANSI T1.404) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
DS3 Pulse Mask (GR-499-CORE). . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
STS-1 Pulse Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
STS-1 Pulse Mask (ANSI T1.102) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Pin Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Package Characteristic Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
AC Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
PRELIMINARY
Preface
The PEF 3452 (TE3-LIU™) is a flexible line interface unit for a wide area of
telecommunication and data communication applications. The device is addressed to
fulfill all requirements to build a DS3, STS-1 or E3 line interface.
Organization of this Document
This Preliminary Data Sheet is organized as follows:
•
•
Overview
Gives a general description of the product, lists the key features, and presents some
typical applications.
Pin Descriptions
Lists pin locations with associated signals, categorizes signals according to function,
and describes signals.
•
•
•
•
•
Functional Description
Describes the functional blocks and principle operation modes.
Interface Description
Describes the device interfaces.
Operational Description
Shows the operation modes and how their initialization.
Electrical Characteristics
Specifies maximum ratings, DC and AC characteristics.
Package Outlines
Shows the mechanical values of the device package.
•
•
Appendix
Index
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
PRELIMINARY
Related Documentation
This document refers to the following international standards
(in alphabetical/numerical order):
ACA TS016 (general requirements for Australia)
CTR-24/TBR-24 (E3 requirements)
ETS 300 166 (E3 transmit return loss)
ITU-T G.703 (E3 pulse mask, B3ZS/HDB3 code, E3 receive return loss)
ITU-T G.751 (jitter requirements E3)
ITU-T G.775 (loss of signal definition)
ITU-T G.823 (jitter requirements E3)
ITU-T G.824 (jitter requirements DS3)
ITU-T O.151 (pseudo random binary sequence (PRBS) definition)
GR-253-CORE (STS-1 jitter requirements)
GR-499-CORE (DS3 pulse mask, DS3 jitter requirements)
ANSI T1.102 (STS-1 pulse mask)
ANSI T1.102 Annex B (DS3 monitoring)
ANSI T1.231 (maintenance functions, defect definitions)
ANSI T1.404 (DS3 pulse mask)
MIL-STD 883D (ESD requirements)
Your Comments
We welcome your comments on this document. We are continuously trying improving
our documentation. Please send your remarks and suggestions by e-mail to
com.docu_comments@infineon.com
Please provide in the subject of your e-mail:
device name (TE3-LIU™), device number (PEF 3452), device version (Version 1.3),
and in the body of your e-mail:
document type (Preliminary Data Sheet), issue date (2001-12-05) and document
revision number (DS1).
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
Overview
PRELIMINARY
1
Overview
The TE3-LIU™ PEF 3452 Line Interface Unit is used to connect a DS3/STS-1 or E3
framer device to an analog transmission line. The line interface fulfills the relevant
standards for DS3 (44.736 Mbit/s), STS-1 (51.840 Mbit/s) and E3 (34.368 Mbit/s)
systems.
The TE3-LIU™ comes in a P-MQFP-44-2 package (SMD) to save a significant amount
of board space. The integrated jitter attenuation further reduces overall system
complexity and cost.
This CMOS 3.3 V low power device contains an integrated pulse shaper to drive any line
length within the range of up to 1100 ft. without the need for external length selection
(Line Build Out).
The hardware configuration mode allows low cost systems with flexible device setting
without the need for a microprocessor.
An optional microprocessor mode allows the connection to a standard microprocessor
bus to control hardware settings.
Preliminary Data Sheet
1
2001-12-05
PRELIMINARY
Line Interface Unit for DS3, STS1 and E3
TE3-LIU™
PEF 3452
Version 1.3
1.1
Features
•
Generic analog interface for all DS3/STS-1/E3
applications
•
•
•
•
•
Single chip solution for receive and transmit direction
3.3 V low power device
Integrated receive equalization network
Integrated noise and crosstalk filter
Clock and data recovery using an integrated PLL
with ultra-low intrinsic jitter
P-MQFP-44-2
•
•
Transmit clock duty cycle correction PLL
No external components required for clock and data
recovery and receive equalizer
•
•
•
•
DSX receive line monitor (additional 20 dB gain according to ANSI T1.102)
Low transmitter output impedances for high transmit return loss
Disable function of the analog transmit line outputs
Transmit pulse shaper to fulfill requirements of ANSI T1.404,
Telcordia GR-499-CORE, ANSI T1.102 and ITU-T G.703 (E3)
Maximum line length up to 1100 ft. (using standard coaxial cable, for example AT&T
728A, 734A or 734D)
•
•
•
•
•
•
•
•
•
•
•
•
•
External line length selection (LBO) is not required
Jitter specifications of GR-499-CORE and ITU-T G.823 are met
Integrated jitter attenuation PLL and buffer in transmit direction
Dual or single rail digital inputs and outputs from/to the framer interface
Selectable line codes (HDB3 (E3), B3ZS (DS3/STS-1), AMI)
Analog and digital loss of signal detection and indication
Automatic RDOP/RDON blanking option in case of LOS
Bipolar violation indication
Local loop and remote loop for diagnostic purposes
Insertion of alarm indication signal ("all ones")
Flexible hardware or software controlled device configuration
Device power down function
Type
Package
PEF 3452 H V1.3
P-MQFP-44-2
Preliminary Data Sheet
2
2001-12-05
PEF 3452
TE3-LIU V1.3
Overview
PRELIMINARY
Hardware Interface Mode
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DS3/STS-1 or E3
Line Coding (E3: HDB3 or AMI; DS3/STS-1: B3ZS or AMI)
Transmitter disable
Power down
Remote loop
Local loop
Single/dual rail operation
Receive clock edge selection
Transmit clock edge selection
Transmit "all ones"
Receive line monitoring mode
Automatic RDOP/RDON blanking option
Jitter attenuation
Loss of signal indication
Bipolar violation indication
Microprocessor Interface Mode
•
•
Microprocessor bus compatible interface
Hardware control lines directly accessible
General
•
•
•
•
•
•
CMOS device
P-MQFP-44-2 package (body size 10 mm × 10 mm, lead pitch 0.8 mm)
Single power supply: 3.3 V ± 5%
5V-tolerant digital input lines
Temperature range of -40°C to +85°C
Low power device
Applications
•
•
•
•
•
•
Interface for SONET/DS3 and E3 network equipment
WAN gateways
CSU/DSU
Multiplexers
Digital crossconnect systems
DS3/STS-1/E3 Test Equipment
Preliminary Data Sheet
3
2001-12-05
PEF 3452
TE3-LIU V1.3
Overview
PRELIMINARY
1.2 Logic Symbol
RDOP
RL1
RL2
RDON/BPV
RCLK
PEF 3452
TE3-LIUTM
XTAL1
XTAL2
LOS
XL1
XL2
XDIP
XDIN
XCLK
HW + µP Access
F0229
Figure 1
Logic Symbol
Preliminary Data Sheet
4
2001-12-05
PEF 3452
TE3-LIU V1.3
Overview
PRELIMINARY
1.3
Typical Applications
Figure 2 to Figure 4 show typical applications using the TE3-LIU™.
QuadLIUTM
DS1 #1
analog
28 x
DS1
#1
digital
DS3
digital
DS3
analog
TE3_LIUTM
TE3-MUXTM
QuadLIUTM
#7
DS1 #28
analog
F0087
Figure 2
T3/T1 Multiplexer Application
DS3
analog
TE3-
CHATTTM
TE3-LIUTM
F0217
Figure 3
Channelized T3 Link Layer Application
DS3
analog
TE3-LIUTM
TE3-MUXTM
DSCC4
F0140
Figure 4
Unchannelized T3 Link Layer Application
Preliminary Data Sheet
5
2001-12-05
PEF 3452
TE3-LIU V1.3
Overview
PRELIMINARY
™
Note: TE3-MUX (PEB 3445) is an M13 MUltipleXer/demultiplexer with an integrated
DS3 framer
™
QuadLIU (PEB 22504) is a 4-channel Line Interface Unit for E1/T1/J1
™
DSCC4 (PEB 20534) is a 4-channel Serial Communication Controller
™
TE3-CHATT (PEB 3456) is a CHAnnelized T3 Termination with DS3
Framer, M13 Multiplexer, T1/E1 Framers and 256 Channel HDLC/PPP
controller
Preliminary Data Sheet
6
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
2
Pin Descriptions
2.1
Pin Diagram
P-MQFP-44-2 (top view)
33
34
31
29
27
25
23
22
TRS
TDI
LOS
XLT
RL
20
18
16
14
12
36
38
40
42
44
TMS
VDDXP
XTAL2
XTAL1
VSSXP
TCK
LL
VDDRP
VSSRP
XAIS
PEF 3452
TE3-LIUTM
BLE
TDO
MON
JATT
VDDX
LCODE
DR/SR
1
3
5
7
9
11
F0230
Figure 5
Pin Configuration
Preliminary Data Sheet
7
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
2.2
Pin Definitions and Functions
Interface Pin Functions
Table 1
Pin No.
Symbol
Input (I)
Function
Output (O)
Supply (S)
Receive Direction
Line Receiver 1
9
RL1
I (analog)
I (analog)
O
Analog input from the external transformer
(receive bipolar ring).
The signal at RL1 must be coded according
to B3ZS or HDB3.
10
25
RL2
Line Receiver 2
Analog input from the external transformer
(receive bipolar tip).
The signal at RL1 must be coded according
to B3ZS or HDB3.
RDOP
Receive Data Output/Positive
Received data at RL1/2 is sent on RDOP/
RDON to the framer interface. Data is
clocked with the rising or falling edge of
RCLK, depending on RPE.
In single rail mode (DR/SR=0), data is sent
in NRZ format.
24
RDON
BPV
O
Receive Data Output/Negative
If dual rail data format is selected, the
negative data signal is output on RDON/
BPV.
Bipolar Violation
If single rail data format is selected, the
bipolar violation indication signal is output
on RDON/BPV. BPV is synchronized on
RCLK.
26
RCLK
O
Receive Clock
Receive Clock extracted from the incoming
data pulses. The active clock edge is
determined by RPE.
During LOS, a clock signal is generated
internally and driven on RCLK (derived
from REFCLK).
Preliminary Data Sheet
8
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 1
Pin No.
Interface Pin Functions (cont’d)
Symbol
Input (I)
Function
Output (O)
Supply (S)
Transmit Direction
1
XL1
O (analog)
O (analog)
I + PU
Transmit Line 1 (transmit bipolar ring)
Analog output to the external transformer.
XL1 can be switched into inactive mode.
3
XL2
Transmit Line 2 (transmit bipolar tip)
Analog output to the external transformer.
XL2 can be switched into inactive mode.
31
XDIP
Transmit Data In/Positive
Transmit data received from the framer
interface to be output on XL1/2. NRZ or
dual rail positive data has to be provided at
XDIP. Latching of data is done with the
rising or falling transitions of XCLK,
depending on XPE.
32
30
XDIN
I + PU
Transmit Data In/Negative
If dual rail format is selected, negative data
signal is read from XDIN. If single rail data
format is selected, data on XDIN is ignored.
Latching of data is done with the rising or
falling transitions of XCLK, depending on
XPE.
XCLK
I + PU
Transmit Clock
Input of the working clock for the
transmitter. The active clock edge is
determined by XPE.
DS3: 44.736 MHz
STS-1: 51.840 MHz
E3: 34.368 MHz
To fulfill e.g. ITU-T G.832 a clock accuracy
of 20 ppm is required. For correct function
a clock signal has always to be supplied to
XCLK.
Preliminary Data Sheet
9
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 1
Pin No.
Interface Pin Functions (cont’d)
Symbol
Input (I)
Function
Output (O)
Supply (S)
Global Clock Reference
29
REFCLK
I
Reference Clock
REFCLK is the basic internal clock. It must
be stable during reset and operation.
This clock is also used to synchronize the
receive PLL in case of no signal.
The clock frequency depends on the target
application:
DS3: 44.736 MHz
STS-1: 51.840 MHz
E3: 34.368 MHz
To fulfill e.g., ITU-T G.832 a clock accuracy
of 20 ppm is required.
39
38
XTAL1
XTAL2
I
Jitter Attenuation Reference
Connection for an external pullable crystal.
O
DS3:
STS-1: 17.280 MHz
E3: 11.456 MHz
14.912 MHz
If jitter attenuation is disabled (default),
XTAL1 is internally driven to a fixed level
(not floating).
Preliminary Data Sheet
10
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 2
Pin No.
Control Pin Functions
Symbol
Input (I)
Function
Output (O)
Supply (S)
33
23
RES
I
Hardware Reset
A low signal at this pin forces the device
into reset state.
CS
I + PU
Chip Select
0 = hardware control signals are switched
through
1 = hardware control signals are ignored
5
DS3/E3
I + PU
DS3/STS-1 or E3 Select
Primary mode selection. This signal has to
be stable during reset and may not change
afterwards. It must not be connected to a
µP bus.
0 = E3
1 = DS3 or STS-1 (see DS3/STS-1)
4
DS3/STS-1 I + PU
DS3 or STS-1 Select
Primary mode selection. This signal has to
be stable during reset and may not change
afterwards. It must not be connected to a
µP bus.
0 = STS-1
1 = DS3
13
LCODE
I + PU
Line Code Select
for receive and transmit direction
E3:
0 = AMI
1 = HDB3
DS3/STS-1:
0 = AMI
1 = B3ZS
16
XAIS
I + PU
Transmit Alarm Indication
0 = no AIS
1 = AIS all-ones insertion
Preliminary Data Sheet
11
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 2
Pin No.
Control Pin Functions (cont’d)
Symbol
RL
Input (I)
Output (O)
Supply (S)
Function
20
19
21
I + PU
I + PU
I + PU
Remote Loop Switching
0 = no loop
1)
1 = Remote Loop
LL
Local Loop Switching
0 = no loop
1 = Local Loop
1)
XLT
Transmitter inactive
0 = transmitter enabled
1 = transmitter disabled
(outputs 1.5 V common mode voltage)
14
15
MON
BLE
I + PU
I + PU
Line Monitoring Mode
0 = additional 20 dB gain at RL1/RL2
1 = normal
Blanking Enable
0 = detected signal is switched through
even in case of LOS
1 = all-zero signal is sent on RDOP/RDON
in case of LOS, REFCLK is used to drive
RCLK
12
DR/SR
I + PU
Dual Rail/Single Rail Select
The framer interface is operated either in
dual rail or single rail mode. In single rail
mode, the BPV signal is output on RDON/
BPV and input on XDIN is ignored.
0 = single rail
1 = dual rail
6
7
RPE
XPE
I + PU
I + PU
RCLK Positive Edge Selection
0 = RDOP, RDON are clocked with
negative (falling) edge of RCLK
1 = RDOP, RDON are clocked with positive
(rising) edge of RCLK
XCLK Positive Edge Selection
0 = XDIP, XDIN are clocked with negative
(falling) edge of XCLK
1 = XDIP, XDIN are clocked with positive
(rising) edge of XCLK
Preliminary Data Sheet
12
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 2
Pin No.
Control Pin Functions (cont’d)
Symbol
Input (I)
Function
Output (O)
Supply (S)
43
JATT
I + PD
Jitter Attenuation Enable
This signal has to be stable during reset
and may not change afterwards. It must not
be connected to a µP bus.
0 = no jitter attenuation (default if left open)
1 = jitter attenuation in transmit direction
22
LOS
O
Loss of Signal Indication
0 = correct signal
1 = loss of signal
LOS is synchronized on RCLK. During
LOS, a clock signal is generated internally
and driven on RCLK.
1)
If RL=LL=1, the device is set into power down mode.
Preliminary Data Sheet
13
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
Table 3
Pin No.
Power Supply Pins
Symbol
Input (I)
Function
Output (O)
Supply (S)
11
8
V
V
V
V
V
V
V
V
V
S (analog)
S (analog)
S (analog)
S (analog)
S (analog)
S (analog)
S (analog)
S (analog)
S
Positive Power Supply
for the analog receiver
DDR
SSR
Power Supply Ground
for the analog receiver
44
2
Positive Power Supply
for the analog transmitter
DDX
SSX
Power Supply Ground
for the analog transmitter
18
17
37
40
27
Positive Power Supply
for the analog receiver PLL
DDRP
SSRP
DDXP
SSXP
DD
Power Supply Ground
for the analog receiver PLL
Positive Power Supply
for the analog transmitter PLL
Power Supply Ground
for the analog transmitter PLL
Positive Power Supply
for digital subcircuits and the digital
receiver output
28
V
S
Power Supply Ground
for digital subcircuits and the digital
receiver output
SS
Preliminary Data Sheet
14
2001-12-05
PEF 3452
TE3-LIU V1.3
Pin Descriptions
PRELIMINARY
1)
Table 4
Pin No.
Test Pins
Symbol
Input (I)
Function
Output (O)
Supply (S)
34
TRS
I + PU
TAP Controller Reset
Active low test controller reset; this pin
must be connected to RST or V
SS
35
36
41
TDI
I + PU
I + PU
I + PU
O
Test Data Input
TMS
TCK
TDO
Test Mode Select
Test Clock
42
Test Data Output
1)
These pins are used for factory test only; boundary scan mode is not provided.
Note: PU = input or input/output comprising an internal pullup device
PD = input or input/output comprising an internal pulldown device
To override the internal pullup (pulldown) by an external pulldown (pullup),
a resistor value of 47 kΩ is recommended.
Unused pins containing pullups or pulldowns can be left open.
Preliminary Data Sheet
15
2001-12-05
PEF 3452
TE3-LIU V1.3
Functional Description
PRELIMINARY
3
Functional Description
3.1
Functional Overview
The TE3-LIU™ device contains analog and digital functional blocks, which are
configured and controlled by direct hardware or microprocessor control.
The main interfaces are
•
•
•
•
Receive Line Interface
Transmit Line Interface
Framer Interface
Hardware Interface
The main internal functional blocks are
•
Analog line receiver with noise & crosstalk filter, equalizer network and clock/data
recovery
•
•
•
•
•
Analog line driver with programmable pulse shaper
Central clock generation module
Jitter attenuator
Maintenance functions (e.g., loop switching local or remote)
Hardware/microprocessor control interface
Preliminary Data Sheet
16
2001-12-05
Autom.
Gain
Control
Level
Detection
ALOS
Detection
LOS
Detection
LOS
LOS, BLE
RL1
RL2
20 dB
Gain
Stage
Clock &
Data
Recovery
RCLK
RDOP
RDON/BPV
Noise
Filter
Var. Gain
Amplifier
Equalizer
Decoder
DR/SR
LCODE
DS3/STS1/E3
REFCLK
MON
Local
Loop
Remote
Loop
LL
RL
Jitter
Attenuator
PLL
XTAL1
XTAL2
JATT
Transmit
PLL
XL1
XL2
Line
Driver
& LBO
Jitter
Attenuator
Buffer
XCLK
XDIP
XDIN
Pulse
Shaper
AIS
Insertion
Encoder
XLT
XAIS
Test Mode Control
DR/SR
LCODE
DS3/STS1/E3
Mode
Control
General
Control
Hardware/µP Interface
F0231
PEF 3452
TE3-LIU V1.3
Functional Description
PRELIMINARY
3.3
Functional Blocks
3.3.1
Hardware Control Unit
All hardware control signals except DS3/E3, DS3/STS-1 and JATT are gated by CS. All
other control signals are gated by CS to allow an easy connection to a microprocessor
(µP) data bus. DS3/E3, DS3/STS-1 and JATT may not be connected to a data bus. If
direct hardware control without µP is intended, CS has to be connected to V
.
SS
After reset all control input values are cleared. The default control values (driven by
internal pullups) are activated after CS = low is applied for the first time after reset.
Table 5
Hardware Control Functions
Device Function
Control Signal
1)
Selection of E3 or DS3/STS-1 mode
DS3/E3
0 = E3
1 = DS3 or STS-1
2)
1)
Selection of DS3 or STS-1 mode
DS3/STS-1
0 = STS-1
2)
1 = DS3
This pin is ignored, if E3 mode is selected
by DS3/E3 = 0
Dual rail select
DR/SR
0 = single rail data on RDOP and XDIP
1 = dual rail data on RDOP/RDON and
2)
XDIP/XDIN
Receive clock edge selection
Transmit clock edge selection
Selection of line coding
RPE
0 = data change on negative edge
1 = data change on positive edge
2)
XPE
0 = data change on negative edge
1 = data change on positive edge
2)
LCODE
0 = AMI
1 = HDB3 (E3)
2)
2)
1 = B3ZS (DS3/STS-1)
Send AIS (all-ones alarm indication signal) XAIS
0 = no insertion
2)
1 = AIS insertion
Preliminary Data Sheet
18
2001-12-05
PEF 3452
TE3-LIU V1.3
Functional Description
PRELIMINARY
Table 5
Hardware Control Functions (cont’d)
Device Function
Control Signal
Select remote loop
Select local loop
RL
0 = normal operation
1 = remote loop
LL
0 = normal operation
1 = local loop
Select power down mode
LL & RL
00 = normal operation
01 = remote loop operation
10 = local loop operation
2)
11 = power down
Blanking enable
BLE
0 = data signal is switched through even
in case of LOS
1 = all-zero signal is transmitted on
RDOP/RDON in case of LOS using RCLK
2)
derived from REFCLK
Line monitoring mode
MON
0 = additional 20 dB gain stage activated
2)
1 = normal amplifier setting
Transmitter inactive mode
Jitter attenuation enable
XLT
0 = normal operation
1 = inactive
2)3)4)
JATT
2)
0 = jitter attenuation disabled
1 = jitter attenuation enabled
1)
to be selected while reset is active (RST = 0)
2)
default, if pin is left open and CS has been asserted at least once
outputs 1.5 V common mode voltage
3)
4)
connecting of CS to VSS or asserting CS in parallel to RES suppresses spurious output on XL1/2
Preliminary Data Sheet
19
2001-12-05
PEF 3452
TE3-LIU V1.3
Functional Description
PRELIMINARY
Table 6
Hardware Indication Signals
Device Function
Indication Signal
Indicate LOS (loss of signal)
Indicate BPV (bipolar violation)
LOS
0 = normal signal
1 = loss of signal
BPV
0 = no violation
1 = bipolar violation
Available in single rail mode only on pin
RDON/BPV.
Preliminary Data Sheet
20
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4
Interface Description
4.1
Receiver
4.1.1
Standard Receiver Application
1 : 1
RL1
75
Ω
C1
TE3-LIUTM
R1
RL2
F0080
Figure 7
Receiver Configuration
External Component Values for Receiver
Table 7
Parameter
Characteristic Line Impedance [Ω]
DS3
STS-1
75
E3
R1 (± 1 %) [Ω]
C1 (± 20 %) [nF]
t2 : t1
75
100
1 : 1
The external components are the same for DS3, STS-1 and E3 applications.
Preliminary Data Sheet
21
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.2
Line Monitoring Application
DSX cross connect point
1 : 1
RL1
75
Ω
75 Ω
C1
TE3-LIUTM
R1
Receiver Mode
RL2
MON=1
R3
1 : 1
RL1
TE3-LIUTM
C1
R2
Monitor Mode
RL2
MON=0
F0081
Figure 8
Table 8
DS3 Line Monitoring
External Component Values for DS Line Monitoring
Parameter
Values
75
R1 (± 1 %) [Ω]
R2 (± 1 %) [Ω]
R3 (± 1 %) [Ω]
47
470
C1 (± 20 %) [nF]
t2 : t1
100
1 : 1
The external components are according to ANSI T1.102 Annex B. The dimensions given
above lead to a signal level at the monitor device input of approximately -20 dB below
the level at the receiver device.
Similar configurations using the line monitoring mode are possible in STS-1 or E3
applications.
Preliminary Data Sheet
22
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.3 Receive Line Interface
The receive line interface consists of a pre-amplifier, a noise and crosstalk filter, a
variable gain amplifier and an equalizer followed by the clock and data recovery.
The noise and crosstalk filter reduces distortions within the incoming analog signal. The
VGA amplifies the analog signal and the equalizer compensates the frequency
dependent line attenuation. Digital signal levels are formed within the retiming block of
the clock and data recovery.
Receive return loss requirements of ITU-T G.703 are fulfilled as required for E3
operation.
Table 9
E3 Receive Return Loss
Frequency Range
Return Loss
from [kHz]
to [kHz]
1720
[dB]
12
860
1720
34368
34368
51550
18
14
The equalizer contains an additional 20 dB gain stage, which is used in line monitoring
mode to amplify resistively attenuated signals.
Reference Clock
Automatic
Gain
Control
False
Lock
Detection
Level
Detection
20 dB
Gain
Stage
Noise &
Crosstalk
Filter
Variable
Gain
Amplifier
RL1
RL2
Receive
PLL
Equalizer
Receive Clock
Retiming
Dual Rail Receive Data
F0094 V1.3
MON
Figure 9
Receive Clock System
Preliminary Data Sheet
23
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.4 Receive Clock and Data Recovery
The receive clock and data recovery extracts the route clock RCLK from the digital data
stream and converts the data stream into a dual rail bit stream. The clock and data
recovery needs a reference clock to keep the PLL stable during times without data signal
at RL1/RL2. The clock that is output on pin RCLK is the recovered clock of the signal
provided on RL1/RL2 and has a duty cycle close to 50 %. The intrinsic jitter generated
in the absence of any input jitter is defined in Chapter 4.1.8. The PLL reference clock is
generated internally without the need for external components.
4.1.5
Receive Line Coding
In E3 applications the HDB3 and the AMI coding is provided for the data received from
the ternary interface. In DS3/STS-1 mode the B3ZS and AMI code is supported. In B3ZS
or AMI code all code violations are detected and indicated.
4.1.5.1
AMI Code
The AMI code is defined as a dual rail data signal, where the combinations 00 ("0"), 10
("+1") and 01 ("-1") are valid. No subsequent "+1" or "-1" bits are allowed, these will be
detected as bipolar violations and indicated on pin RDON/BPV, if single rail mode is
selected (according to ANSI T1.231 chapter 7.1).
The received AMI data stream is either switched transparently to the framer interface as
dual rail data or converted into a single rail data stream.
4.1.5.2
B3ZS Code
In the B3ZS line code each block of three consecutive zeros is replaced by either of two
replacements codes which are B0V and 00V, where B represents a pulse which applies
to the bipolar rule ("+1" or "-1") and V represents a bipolar violation (two consecutive "+1"
or "-1" bits). The replacement code is chosen in a way that there is an odd number of
valid B pulses between consecutive V pulses to avoid the introduction of a DC
component into the analog signal.
The receive line decoder decodes the incoming B3ZS data signal and changes the
replacement patterns to the original three-zeros pattern. Pattern sequences violation
these rules are reported as bipolar violation errors.
Data output to the framer interface can be selected to be either dual rail or single rail.
Preliminary Data Sheet
24
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.5.3 HDB3 Code
In the HDB3 line code each block of four consecutive zeros is replaced by either of two
replacements codes which are B00V and 000V, where B represents a pulse which
applies to the bipolar rule ("+1" or "-1") and V represents a bipolar violation (two
consecutive "+1" or "-1" bits). The replacement code is chosen in a way that there is an
odd number of valid B pulses between consecutive V pulses to avoid the introduction of
a DC component into the analog signal.
The receive line decoder decodes the incoming HDB3 data signal and changes the
replacement patterns to the original three-zeros pattern. Pattern sequences violation
these rules are reported as bipolar violation errors.
Data output to the framer interface can be selected to be either dual rail or single rail.
4.1.6
Alarm Handling
The receive line interface includes the alarm detection for loss of signal (LOS). LOS is
indicated either if an analog or a digital loss of signal condition is detected.
During LOS a clock signal is sent on RCLK. The clock is internally derived from REFCLK.
4.1.6.1
DS3 LOS Definition
Detection and recovery of digital LOS defects in DS3 mode is done according to ANSI
T1.231:
An LOS defect occurs when 175 contiguous pulse positions with no pulses of either
positive or negative polarity at the line interface are detected. An LOS defect is
terminated upon detecting an average pulse density of at least 33% over a period of 175
contiguous pulse positions following the receipt of a pulse. An LOS defect shall not be
terminated if, at the end of the pulse-position interval, any subintervals of 100 pulse
positions contain no pulses of either polarity.
4.1.6.2
STS-1 LOS Definition
Detection and recovery of digital LOS defects in STS-1 mode is defined in ANSI T1.231
(chapter 8.1.2.1.1) as follows:
An LOS defect occurs upon detection of no transitions on the incoming signal (before
descrambling) for time T, where 2.3 ≤ T ≤ 100 µs.
The LOS defect is terminated after a time period equal to the greater of 125 µs or 2.5×T’
containing no transition-free interval of length T’, where 2.3 ≤ T’ ≤ 100 µs.
Preliminary Data Sheet
25
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.6.3 E3 LOS Definition
Analog LOS is detected, if the signal level on pins RL1/2 drops below a fixed level ("B")
for a certain period. Loss of signal level "B" is defined to be between 15 and 35 dB below
normal signal level "A". If the signal exceeds 35 dB for 175 contiguous pulse periods,
analog LOS defect is indicated.
Analog LOS defect is cleared, if the signal exceeds a threshold of 15 dB below nominal
level for 175 contiguous pulse periods (10 ≤ N ≤ 255). See ITU-T G.775 for reference.
A
B
see ITU-T G.775 page 4
Nominal value
0 dB
"transition condition" must
be detected
15 dB
Tolerance range, "no transition condition" or "transition
condition" may be declared
"no transition condition"
must be detected
35 dB
F0101 V1.2
Figure 10
E3 Loss of Signal Definition
Preliminary Data Sheet
26
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.1.7 Jitter Tolerance
The TE3-LIU™ receiver’s tolerance to input jitter complies to and exceeds the relevant
international standards. Especially the requirements of Telcordia GR-499-CORE (DS3),
ITU-T G.824 (DS3), GR-253-CORE (STS-1) and ITU-T G.823 (E3) are fulfilled and
exceeded. Figure 11 and Table 10 show the different input jitter specifications. Low
frequency jitter is called "wander", where the defined border between jitter and wander
is 10 Hz for DS3/E3 and 100 Hz for STS-1.
A1
pass
A2
fail
A3
F1
F2
F3
F4
F5
F6
Jitter Frequency
F0085
Figure 11
Jitter Tolerance Principle
Table 10
Input Jitter Requirements
Reference
A1
A2
[UI
0.1
A3
F1
F2
F3
F4
[Hz]
2300 60 × 300 ×
F5
F6
]
PP
not
def.
not
def.
not
def.
GR-499-CORE,
Category I
5
10
10
3
3
10
10
not
def.
not
def.
not
def.
GR-499-CORE, 10
Category II
0.3
1.5
669
22.3 300 ×
× 10
3
3
10
not
def.
GR-253-CORE, 15
Category II
0.15 10
30
300
2 ×
20 ×
3
3
10
10
not
def.
not
def.
not
def.
ITU-T G.823
& ETSI TBR24
1.5
0.15
5
100
1000 10 × 800 ×
3
3
10
10
600
not
def.
ITU-T G.824
18 µs
0.1
1.2 × 10
30 × 400 ×
-5
3
3
10
10
10
Preliminary Data Sheet
27
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
100
10
1
pass area
fail area
0,1
0,01
0,10
1,00
10,00
100,00
1000,00
10000,00
100000,00
1000000,00
Jitter Frequency [Hz]
TE3-LIU
GR-499-CORE Cat. 1
GR-499-CORE Cat. 2
ITU-T G.823
ITU-T G.824
GR-253-CORE Cat. 2
F0104
Figure 12
Jitter Tolerance
GR-499-CORE Jitter Tolerance Requirements (DS3)
The input jitter tolerance is defined as the minimum amplitude of sinusodial jitter at a
given frequency that when modulating the signal at an equipment input port results in
more than 2 errored seconds in a 30-second measurement interval. Requirements on
input jitter tolerances are then given in terms of a jitter tolerance mask, which represents
the minimum acceptable jitter tolerances for a specified range of jitter frequencies.
There are two different jitter tolerance masks defined for Category I (SONET interfaces)
and Category II (non-SONET interfaces) equipment.
GR-253-CORE Jitter Tolerance Requirements (STS-1)
For Category I interfaces, the same requirements are used as defined in GR-499-CORE.
For Category II interfaces that are specified as having reduced jitter tolerance, shall
tolerate, as a minimum, input jitter applied according to the mask given in Table 10.
4.1.8
Receive Output Jitter
The intrinsic jitter of the receiver output signal RDOP/RDON/RCLK (if no input jitter is
applied) is
•
•
•
E3:
DS3:
STS-1: < 0.10 UI
< 0.06 UI
< 0.08 UI
Preliminary Data Sheet
28
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.2 Transmitter
The serial bit stream is then processed by the transmitter which has the following
functions:
•
•
generation of AMI, B3ZS (DS3/STS-1) or HDB3 (E3) coded signals
all-ones generation (alarm indication signal)
4.2.1
Transmit Line Interface
The received data stream on pins XDIP (single rail data) or XDIP/XDIN (dual rail data) is
converted into a ternary signal which is output on pins XL1 and XL2. In E3 mode the
HDB3 and AMI line code are supported, in DS3/STS-1 mode the B3ZS and AMI is
supported.
R1
R1
t1 : t2
XL1
75
Ω
TE3-LIUTM
CP
XL2
F0079
Figure 13
Transmitter Configuration
Table 11
External Component Values for Transmitter
Parameter
Characteristic Line Impedance [Ω]
DS3
STS-1
75
E3
1)
R1 (± 1 %) [Ω]
37.5
2)
C [pF]
37
p
t2 : t1
1 : 1
1)
This value refers to an ideal transformer without any parasitics. Any transformer resistance or other parasitic
resistances have to be taken into account when calculating the final value for the output serial resistors.
2)
This value includes all parasitic capacitances on the secondary side of the transformer.
The external components are the same for DS3, STS-1 and E3 applications. Transmit
return loss requirements for E3 defined in ETS 300 166 are fulfilled. Pulse mask
Preliminary Data Sheet
29
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
requirements according to ANSI T1.102 (at cross connect point, up to 450 ft.) are
fulfilled.
Note: An additional capacitor on the primary or secondary side of the transformer may
be required in some applications to improve the pulse mask, if the parasitic
capacitances of the PCB are very small.
Table 12
E3 Transmit Return Loss
1)
Frequency Range
Return Loss
from [kHz]
to [kHz]
1720
[dB]
860
6
8
1720
51550
1)
measured with an unframed PRBS 215-1 pattern
4.2.2
Transmit Clock System
The supplied transmit clock XCLK is duty-cycle corrected by an internal PLL circuit to
provide a 50% clock signal to the internal line driver unit. The pulse shaper working
frequency is fourfold of the XCLK frequency.
If the transmit clock XCLK is failing, an all-zero signal is generated automatically.
If AIS insertion is selected, the output signal is referenced to REFCLK.
XAIS
fnom
REFCLK
Transmit
PLL
fnom : 3
JATT
XTAL1
XTAL2
Jitter
Attenuator
PLL
fnom x 4
fnom
fnom
disable
testmode
XAIS
XCLK
XDIP
XDIN
Jitter
Attenuator
Buffer
XL1
XL2
AIS
Insertion
Pulse
Shaper
Encoder
Line Driver
F0232
Figure 14
Transmit Clock System
Preliminary Data Sheet
30
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.2.3 Jitter Attenuation
Jitter is reduced in transmit direction, if the jitter attenuator is activated (JATT = 1). The
JATT control signal enables/disables the jitter attenuation PLL and activates/bypasses
the buffer.
The jitter attenuator consists of a buffer and a PLL. The jitter attenuation PLL delivers a
"jitter free" clock (nominal frequency divided by 3, see Table 13) to the transmit PLL
which generates the buffer read clock. The jitter attenuation PLL uses a pullable crystal
and supports a tuning range of ± 150 ppm.
The jitter attenuator uses a 64-bit dual rail buffer and fulfills the requirements of GR-499-
CORE and GR-253-CORE as shown in Figure 15. This covers the requirements of ITU-
T G.751, G.752 and G.755 as well.
To avoid the need for a high frequency crystal, the reference clock for the jitter
attenuation PLL is only one third of the nominal frequency. A detailed block diagram of
the transmit clocking is given in Figure 14.
Table 13
Jitter Attenuation PLL Operation Frequencies
Operation mode
Jitter Attenuation Jitter Attenuation Crystal Frequency
PLL Input
PLL Output
Frequency
Frequency
DS3
STS-1
E3
44.736 MHz
51.840 MHz
34.368 MHz
14.912 MHz
17.280 MHz
11.456 MHz
14.912 MHz
17.280 MHz
11.456 MHz
Further requirements for the external crystal are found in Table 21 on page 45.
Preliminary Data Sheet
31
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
20 dB/decade
0.5 dB
ITU-T G.755 &
0.1 dB
- 20 dB
- 40 dB
GR-499-CORE
ITU-T G.751
TE3-LIU
ITU-T G.752
GR-253-CORE
10
40 100 300
1000
10000
15000
100000
F0141
Jitter Frequency
Figure 15
4.2.4
Jitter Attenuation Characteristic
Intrinsic Jitter
The TE3-LIU™ transmit PLL generates an output jitter which fulfills the requirements as
specified in Table 14 below.
Table 14
Transmit Output Jitter
Measurement Filter Bandwidth
1)
Specification
Output Jitter
Lower Cutoff
Upper Cutoff
GR-499-CORE
(DS3)
10 Hz
300 kHz
< 1.0 UI
< 0.3 UI
< 0.5 UI
PP
rms
PP
ANSI T1.404
(DS3)
10 Hz
400 kHz
400 kHz
400 kHz
30 kHz
12 kHz
< 0.05 UI
PP
GR-253-CORE
(STS-1)
< 1.0 UI
< 0.3 UI
< 0.4 UI
PP
rms
PP
ETSI TBR24
(E3)
100 Hz
10 kHz
800 kHz
800 kHz
< 0.15 UI
PP
1)
Measured with maximum input jitter applied (see Figure 12).
Preliminary Data Sheet
32
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.2.5 Pulse Shaper
The internal pulse shaper generates the required pulse shapes for E3, DS3 and STS-1
signals according to ANSI T1.102, T1.404, Telcordia GR-499-CORE and ITU-T G.703).
The specific pulse mask is fulfilled at the crossconnect point at a distance of 0 to 450 ft.
to the transmitter (DS3 requirement).
The maximum line length between a TE3-LIU™ transmitter and TE3-LIU™ receiver is
1100 ft. for a coaxial cable of AT&T type 728A, 734A or 734D.
4.2.6
Transmit Line Coding
AMI Code
4.2.6.1
The AMI code is defined as a dual rail data signal, where the combinations 00 ("0"), 10
("+1") and 01 ("-1") are valid. Additionally no subsequent "+1" or "-1" bits are allowed
(bipolar violations). A dual rail data stream is passed transparently, even if it contains
bipolar violations. A single rail data stream is encoded to a correct AMI coded bipolar
data stream without zero code suppression.
4.2.6.2
B3ZS Code
In the B3ZS line code each block of three consecutive zeros is replaced by either of two
replacements codes which are B0V and 00V, where B represents a pulse which applies
to the bipolar rule ("+1" or "-1") and V represents a bipolar violation (two consecutive "+1"
or "-1" bits). The replacement code is chosen in a way that there is an odd number of
valid B pulses between consecutive V pulses to avoid the introduction of a DC
component into the analog signal.
The transmit line encoder detects three-zeros pattern sequences and changes them to
the appropriate replacement pattern.
Although B3ZS coding is normally used with single rail NRZ data, the transmit line
encoder accepts either dual rail or single rail data. Bipolar violations in an incoming dual
rail data stream are converted to valid data pulses.
4.2.6.3
HDB3 Code
In the HDB3 line code each block of four consecutive zeros is replaced by either of two
replacements codes which are B00V and 000V, where B represents a pulse which
applies to the bipolar rule ("+1" or "-1") and V represents a bipolar violation (two
consecutive "+1" or "-1" bits). The replacement code is chosen in a way that there is an
odd number of valid B pulses between consecutive V pulses to avoid the introduction of
a DC component into the analog signal.
The transmit line encoder detects three-zeros pattern sequences and changes them to
the appropriate replacement pattern.
Preliminary Data Sheet
33
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
Although HDB3 coding is normally used with single rail NRZ data, the transmit line
encoder accepts either dual rail or single rail data. Bipolar violations in an incoming dual
rail data stream are converted to valid data pulses.
4.2.7
AIS Insertion
An unframed all-ones signal can be inserted into the transmitted data stream. To fulfill
the required accuracy, a reference clock of ± 20 ppm is needed on pin REFCLK.
If local loop configuration and AIS insertion is selected together, the AIS signal is looped
back to RDOP/RDON.
4.3
Framer Interface
The interface to the receive framer is realized by RDOP, RDON and RCLK. Data at
RDOP/N are clocked off with either the rising (RPE=1) or falling edge (RPE=0) of RCLK.
Alternatively a single rail signal can be selected to be output on pin RDOP (DR/SR=0).
Bipolar violation indications are output on pin RDON/BPV in this case.
Data from the framer interface are sampled at XDIP and XDIN on the active edge of the
XCLK. The active edge can be the rising (XPE=1) or falling edge (XPE=0) of XCLK.
Alternatively a single rail signal can be used on pin XDIP (DR/SR=0).
Note: Selection of dual rail/single rail mode is common to receive and transmit direction.
See Figure 24 on page 47 and Figure 25 on page 48 for details.
Preliminary Data Sheet
34
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.4
Maintenance Functions
4.4.1
Remote Loop
In the remote loopback mode the clock and data recovered from the line inputs RL1/2
are routed back to the line outputs XL1/2. As in normal mode they are also processed by
the synchronizer and then sent to the framer interface. Data passes the decoder and
encoder circuit. The recovered receive clock is used to drive the transmit pulse shaper.
RL1
RL2
RDON
RDOP
RCLK
Noise &
Crosstalk
Filter
Clock &
Data
Recovery
Equalizer
Decoder
Remote
Loop
XL1
XL2
XDIN
XDIP
XCLK
Line
Driver
Pulse
Shaper
Jitter
Attenuator
Encoder
F0083
Figure 16
Remote Loop Signal Flow
Note: If remote loop and local loop are selected simultaneously, the device will be set
into power down mode.
Note: The jitter attenuator can be switched off optionally.
Preliminary Data Sheet
35
2001-12-05
PEF 3452
TE3-LIU V1.3
Interface Description
PRELIMINARY
4.4.2 Local Loop
The local loopback mode disconnects the receive lines RL1/2 from the receiver. Instead
of the signals coming from the line data provided by system interface is routed through
the analog receiver back to the framer interface. The transmit bit stream is sent to the
transmit line unchanged. If XAIS=1 is selected, the transmit data stream is replaced by
an all-ones signal and looped back.
RL1
RL2
RDON
RDOP
RCLK
Noise &
Crosstalk
Filter
Clock &
Data
Recovery
Equalizer
Decoder
Local
Loop
XL1
XL2
XDIN
XDIP
XCLK
Line
Driver
Pulse
Shaper
Jitter
Attenuator
Encoder
F0084
Figure 17
Local Loop Signal Flow
Note: If remote loop and local loop are selected simultaneously, the device will be set
into power down mode.
Note: The jitter attenuator can be switched off optionally.
Preliminary Data Sheet
36
2001-12-05
PEF 3452
TE3-LIU V1.3
Operational Description
PRELIMINARY
5
Operational Description
5.1
Operational Overview
The TE3-LIU™ can be operated in three principle modes, which are either E3, DS3 or
STS-1 mode. This basic operation mode selection has to be stable before the reset
signal goes inactive.
The device is programmable by pin selection. Direct connection to a microprocessor
data bus is possible by using the chip select pin (CS) as a write strobe.
5.2
Device Reset
The TE3-LIU™ is forced to the reset state if a low signal is input on pin RES (for minimum
period see page 42). During reset, all output stages are in a high impedance state, all
internal flip-flops are reset.
The basic device mode (DS3, STS-1 or E3, jitter attenuation) has to be selected during
reset to enable the internal PLLs to adjust.
After reset all control input values are cleared. The default control values (driven by
internal pullups) are activated after CS = low is applied for the first time after reset.
5.3
Device Power Down
The TE3-LIU™ can be set into power down state to reduce power consumption, if not
active. Power down mode is selected by setting RL=LL=1. Receive and transmit circuits
are switched off including internal PLLs and transmit line driver. Recovery from power
down mode is achieved by clearing either of RL or LL (RL = 0 and/or LL = 0). After
recovery from power down, the internal PLLs need to stabilize again. REFCLK must be
active to recover from power down mode.
Internal pullup resistors are not switched off during power down to prevent open input
lines from floating.
Note: If switching directly from local loop to remote loop or vice versa, make sure that
there is no signal overlap, which would set the device into power down mode
unintentionally.
5.4
Transmit Line Inactive
If the transmitter is not used, it can be switched into inactive mode by setting XLT=1.
During inactive state the common mode voltage of 1.5 V is output on XL1 and XL2. The
transmit PLL is not stopped and output can be enabled again by XLT=0 without wait time.
Preliminary Data Sheet
37
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6
Electrical Characteristics
6.1
Absolute Maximum Ratings
Maximum Ratings
Table 15
Parameter
Symbol
TA
Limit Values
– 40 to 85
Unit
°C
°C
V
Ambient temperature under bias
Storage temperature
Tstg
– 65 to 150
– 0.4 to 4.5
– 0.4 to 4.5
– 0.4 to 4.5
– 0.4 to 4.5
IC supply voltage (digital)
VDD
IC supply voltage receive (analog)
IC supply voltage transmit (analog)
VDDR
VDDX
VSO
V
V
Voltage on any output pin
with respect to ground
V
Voltage on any input pin with
respect to ground
VSI
– 0.4 to 5.5
V
V
1)
ESD robustness
VESD,HBM 2000
HBM: 1.5 kΩ, 100 pF
1)
According to MIL-Std 883D, method 3015.7 and ESD Ass. Standard EOS/ESD-5.1-1993.
Note: Stresses above those listed here may cause permanent damage to the
device. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
Preliminary Data Sheet
38
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.2
Operating Range
Table 16
Parameter
Power Supply Range
Symbol
Limit Values
Unit Condition
min.
max.
85
Ambient temperature
Supply voltage
TA
-40
°C
VDD
3.13
3.46
V
3.3 V ± 5%
5.0 V + 5%
VDDR
VDDX
VDDRP
VDDXP
Digital input voltages
Ground
VID
0
0
5.25
0
V
V
VSS
VSSR
VSSX
VSSRP
VSSXP
Note: In the operating range, the functions given in the circuit description are fulfilled.
All V pins have to be connected to the same voltage level,
DD
All V pins have to be connected to ground level.
SS
Note: Typical characteristics specify mean values expected over the production spread.
If not otherwise specified, typical characteristics apply at TA = 25 °C and 3.3V
supply voltage.
Preliminary Data Sheet
39
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.3
DC Characteristics
DC Parameters
Symbol
Table 17
Parameter
Limit Values
Unit Notes
min.
max.
0.8
Input low voltage
Input high voltage
Output low voltage
Output high voltage
VIL
– 0.4
2.0
V
VIH
5.25
0.45
V
1)
VOL
VOH
IDD
V
V
IOL = + 4 mA
IOH = – 4 mA
1)
2.4
Average power
supply current
110 (typ.)
155 (typ.)
mA typical (DS3,
PRBS, JATT
enabled, 3.3 V)
worst case (STS-1,
JATT enabled, AIS,
3.46 V)
2)
Input leakage current
Input leakage current
Input pullup current
IIL11
IIL12
IIPU
1
1
µA VIN = VDD
2)
µA VIN = VSS
µA VIN = VSS
2
25
5 (typ.)
– 25
-5 (typ.)
1
Input pulldown current
IIPU
ITL
– 2
µA VIN = VDD
Transmitter leakage
current
mA XL1/2 = VDDX
,
XLT = 1
1
200
mA XL1/2 = VSSX
,
XLT = 1
3)
µA
Ω
V
XL1/2 = 1.50 V ,
XLT = 1
Transmitter output
impedance
RX
5 (typ.)
2.0
applies to XL1and
4)
XL2
Differential peak voltage of VX
a mark (at XL1/XL2)
Receiver differential peak VR
voltage of a mark
V
3
+0.
V
RL1, RL2
DDR
(at RL1/RL2)
3)
Receiver input impedance ZR
tbd.
kΩ
Preliminary Data Sheet
40
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
Table 17
DC Parameters (cont’d)
Parameter (cont’d)
Symbol
Limit Values
Unit Notes
min.
max.
Receiver sensitivity
SRSH
0
tbd.
dB
dB
RL1, RL2
Analog loss of Signal
threshold E3
VLOS3
-35
– 15
1)
applies to all output pins except analog pins XL1/XL2
2)
Input leakage currents of pins containing internal pullup devices are measured in a testmode which switches
off the pullups.
3)
4)
test against common mode voltage, parameter not tested in production
parameter not tested in production
Preliminary Data Sheet
41
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4
AC Characteristics
Reset
6.4.1
1
RES
2
DS3/E3
DS3/STS-1
JATT
3
(PLLs tuned)
F0095
Figure 18
Table 18
Reset Timing
Reset Timing Parameter Values
No.
Parameter
Limit Values
Unit
min.
10
max.
1
2
RES pulse width low
µs
DS3/E3, DS3/STS-1, JATT to RES setup
time
5
ns
3
PLL startup time
1000
µs
Note: REFCLK must be active during reset.
Preliminary Data Sheet
42
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.2
Reference Clock
1
2
3
REFCLK
4
5
F0107
Figure 19
Table 19
Reference Clock Timing
REFCLK Timing Parameter Values
No.
Parameter
Limit Values
Unit
min.
typ.
29.1
22.4
19.3
max.
1
REFCLK period E3
ns
ns
ns
%
REFCLK period DS3
REFCLK period STS-1
REFCLK high
2
3
4
5
20
20
80
80
REFCLK low
%
1)
REFCLK rise time
REFCLK fall time
Clock accuracy
4
ns
ns
ppm
1)
4
2)
20
1)
not tested in production
2)
if DS3-AIS function is not required, 200 ppm is sufficient to guarantee correct receive PLL function
Preliminary Data Sheet
43
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.3
Jitter Attenuator Reference Clock
1
2
3
XTAL1
4
5
F0164
Figure 20
XTAL Clock Timing
•
Table 20
XTAL Timing Parameter Values
No.
Parameter
Limit Values
Unit
min.
typ.
max.
1
XTAL1/2 period E3
87.29
67.06
57.87
ns
ns
ns
XTAL1/2 period DS3
XTAL1/2 period STS-1
CL
XTAL1
DS3: 14.912 MHz
STS-1: 17.280 MHz
TE3-LIUTM
CL
E3:
11.456 MHz
XTAL2
F0245
Figure 21
Recommended Crystal Circuit
44
Preliminary Data Sheet
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
+200
+150
+100
+50
0
f - f0
f0
nominal value
[ppm]
-50
-100
-150
-200
10
15
20
Load Capacitance CLeff [pF]
F0259
Figure 22
Table 21
Crystal Pulling Range
XTAL Crystal Parameter Values
No.
Parameter
Limit Values
Unit
min.
typ.
14.912
17.280
11.456
25
max.
1
Crystal nominal frequency DS3
Crystal nominal frequency STS-1
Crystal nominal frequency E3
MHz
MHz
MHz
fF
2
3
4
5
Crystal motional capacitance C
1
Crystal shunt capacitance C
7
pF
0
1)
Crystal load capacitance C
15
pF
Leff
Crystal resonance resistance R
30
Ω
r
6
Internal parasitic load capacitance C
7.5
pF
Lint
1)
This value includes the capacitance of the external capacitors (CLext) plus all internal (CLint) and external
parasitic capacitances (CLpara). The value of the external capacitor has to be chosen depending on the printed
circuit board layout. A typical value for CL is 0 to 10 pF, CL should be adapted to the parasitics to achieve a
symmetrical pulling range.
Note: C
= C
+ C
+ C
Lint Lpara
Leff
Lext
C
= 0.5 x C
Lext
L
Preliminary Data Sheet
45
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.4 Microprocessor Control
1
2
CS
3
4
Control Signal
F0097
Figure 23
Table 22
Chip Select Timing
Chip Select Timing Parameter Values
No.
Parameter
Limit Values
min. max.
2.5 × T
Unit
1
CS pulse width low
RCLK
E1
DS3
73
ns
ns
ns
56
50
STS-1
2
CS pulse width high
2.5 × T
73
RCLK
E1
DS3
ns
ns
ns
ns
ns
56
STS-1
50
3
4
Control Signal Setup Time
Control Signal Hold Time
10
10
Preliminary Data Sheet
46
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.5 Transmit Input Timing
1
2
3
XCLK (XPE=0)
XCLK (XPE=1)
XDIP, XDIN
6
7
4
5
data change edge
F0090
Figure 24
Table 23
XCLK Input Timing
XCLK Timing Parameter Values
No.
Parameter
Limit Values
Unit
min.
typ.
29.1
22.4
19.3
max.
1
XCLK period E3
ns
ns
ns
%
XCLK period DS3
XCLK period STS-1
XCLK high
2
3
4
5
6
7
30
30
2
70
70
XCLK low
%
XDIP, XDIN setup time
XDIP, XDIN hold time
XDIP, XDIN, XCLK rise time
XDIP, XDIN, XCLK fall time
Clock accuracy
ns
ns
ns
ns
ppm
2
1)
1
1)
1
2)
8
20
1)
not tested in production
2)
if DS3-AIS function is not required, 200 ppm is sufficient to guarantee correct PLL function
Preliminary Data Sheet
47
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.6 Receive Output Timing
1
2
3
RCLK (RPE=0)
RCLK (RPE=1)
RDOP, RDON
5
6
4
data change edge
F0108
Figure 25
Table 24
RCLK Output Timing
RCLK Timing Parameter Values
No.
Parameter
Limit Values
Unit
min.
typ.
max.
1)
1
RCLK period E3
29.1
22.4
19.3
50
50
1
ns
ns
ns
%
1)
1)
RCLK period DS3
RCLK period STS-1
RCLK high
2
3
4
5
40
40
0
60
60
RCLK low
%
2)
RDOP, RDON delay time
RDOP, RDON, RCLK rise time
RDOP, RDON, RCLK fall time
2
ns
ns
ns
2)
2
5
2)
6
2
5
1)
applies only while the receiver PLL is locked to a valid signal on RL1/RL2, e.g., not in case of LOS
not tested in production
2)
Preliminary Data Sheet
48
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.7
Pulse Templates
6.4.7.1
Pulse Template E3
17 ns
(14.55 + 2.45)
V
1.0
8.65 ns
(14.55 – 5.90)
Nominal pulse
14.55 ns
0.5
12.1 ns
(14.55 – 2.45)
24.5 ns
(14.55 + 9.95)
0
29.1 ns
(14.55 + 14.55)
FIGURE 17/G.703
F0076
Figure 26
Table 25
E3 Pulse Shape at Transmitter Output
1)
E3 Pulse Mask
No.
Parameter
Limit Values
Unit
min.
typ.
max.
Nominal peak voltage of a mark (pulse)
Peak voltage of a space (no pulse)
Nominal pulse width
1.0
V
- 0.1
0.1
V
14.55
ns
2)
Amplitude ratio of positive to negative pulses
0.95
0.95
1.05
1.05
3)
Pulse width ratio of positive to negative pulses
1)
measured at the output port without transmission line and 75Ω load;
bit sequence: 0000000(+1)0000000(-1)0000000(+1)0000000(-1)...
2)
3)
at the center of a pulse interval
at the nominal half amplitude
Preliminary Data Sheet
49
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.7.2
Pulse Template DS3
1.2
1.0
0.8
0.6
0.4
0.2
0
GR-499-CORE
ANSI T1.404
-0.2
-1.0
-0.5
0
0.5
1.0
1.5
Time [unit intervals]
F0077
Figure 27
Table 26
DS3 Pulse Shape at the Cross Connect Point (450 ft.)
1)
DS3 Pulse Mask (ANSI T1.404, GR-499-CORE)
Absolute Voltage Level (100 % Value)
min.
max.
0.36 V
0.85 V
1)
bit sequence: 0000000(+1)0000000(-1)0000000(+1)0000000(-1)...
Preliminary Data Sheet
50
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
Table 27
DS3 Pulse Mask (ANSI T1.404)
Lower Curve
Time
Equation
T ≤ -0.36
-0.03
-0.36 ≤ T ≤ +0.36
π
2
T
0.18
--
0.5 1 + sin 1 + ----------- – 0.03
T ≥ +0.36
-0.03
Upper Curve
Time
Equation
+0.03
T ≤ -0.68
-0.68 ≤ T ≤ +0.36
π
2
T
0.34
--
0.5 1 + sin 1 + ----------- + 0.03
T ≥ +0.36
0.05 + 0.407 × e-1.84[T – 0.36]
Table 28
DS3 Pulse Mask (GR-499-CORE)
Lower Curve
Time
Equation
-0.85 ≤ T ≤ -0.36
-0.36 ≤ T ≤ +0.36
-0.03
π
2
T
--
0.5 1 + sin 1 + ----------- – 0.03
0.18
+0.36 ≤ T ≤ +1.4
-0.03
Upper Curve
Time
Equation
+0.03
-0.85 ≤ T ≤ -0.68
-0.68 ≤ T ≤ +0.36
π
2
T
0.34
--
0.5 1 + sin 1 + ----------- + 0.03
+0.36 ≤ T ≤ +1.4
0.08 + 0.407 × e-1.84[T – 0.36]
Preliminary Data Sheet
51
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.4.7.3
Pulse Template STS-1
1.2
1.0
0.8
0.6
0.4
0.2
0
-0.2
-1.0
-0.5
0
0.5
1.0
1.5
Time [unit intervals]
F0109
Figure 28
Table 29
STS-1 Pulse Shape at the Cross Connect Point (450 ft.)
1)
STS-1 Pulse Mask
Signal Power
min.
max.
- 2.7 dBm
+ 4.7 dBm
1)
bit sequence: (+1)0(-1)0(+1)0(-1)...
Table 30
STS-1 Pulse Mask (ANSI T1.102)
Lower Curve
Time
Equation
-0.85 ≤ T ≤ -0.38
-0.38 ≤ T ≤ +0.36
-0.03
π
2
T
--
0.5 1 + sin 1 + ----------- – 0.03
0.18
+0.36 ≤ T ≤ +1.4
-0.03
Preliminary Data Sheet
52
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
Upper Curve
Time
Equation
+0.03
-0.85 ≤ T ≤ -0.68
-0.68 ≤ T ≤ +0.26
π
T
--
0.5 1 + sin 1 + ----------- + 0.03
2
0.34
+0.26 ≤ T ≤ +1.4
0.1 + 0.61 × e-2.4[T – 0.26]
Preliminary Data Sheet
53
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.5
Capacitances
Pin Capacitances
Symbol
Table 31
Parameter
Limit Values
Unit Notes
min.
max.
10
1)
Input capacitance
CIN
5
8
8
pF
1)
1)
Output capacitance
COUT
COUT
15
pF
pF
all except XL1, XL2
XL1, XL2
Output capacitance
20
1)
not tested in production
6.6
Package Characteristics
F0051
Figure 29
Thermal Behavior of Package
Table 32
Package Characteristic Values
Parameter
Symbol
Limit Values
min. typ. max.
63
Unit Notes
1)
2)
Thermal Resistance
Junction to Ambient
R
R
R
K/W single layer PCB,
thJA
thJC
j
30%/11 µm
metallization,
Thermal Resistance
Junction to Case
15
K/W
1W, no convection
°C
Junction Temperature
125
1)
RthJA = (Tjunction - Tambient)/Power
not tested in production
2)
RthJC = (Tjunction - Tcase)/Power
not tested in production
Preliminary Data Sheet
54
2001-12-05
PEF 3452
TE3-LIU V1.3
Electrical Characteristics
PRELIMINARY
6.7
Test Configuration
AC Test Level
External Load
Device
under
Test
VT
CL
Timing Test
Points
Drive Levels
VIH
F0206
VIL
Figure 30
Input/Output Waveforms for AC Testing
AC Test Conditions
Table 33
Parameter
Symbol
Test
Unit Notes
Values
Load Capacitance 1
Load Capacitance 2
Load Capacitance 3
CL1
50
pF
pF
pF
digital outputs except
RDOP, RDON, RCLK
CL2
15
50
digital outputs RDOP,
RDON and RCLK
CL3
analog line output
XL1, XL2
Input Voltage high
Input Voltage low
Test Voltage
VIH
VIL
VT
RL
TR
TF
2.4
0.4
V
all except RL1, RL2
all except RL1, RL2
all except XL1, XL2
XL1, XL2
V
V
/2
V
DD
Output Test Load
Rise Times
75 ± 5%
10 - 90
90 - 10
Ω
%
%
not tested in
production
Fall Times
Note: Typical characteristics are mean values expected over the production spread. If
not specified otherwise, typical characteristics apply at TA = 25 °C and V = 3.3V.
DD
Note: Capacitance values include all parasitics caused by board layout, transformer etc.
Preliminary Data Sheet
55
2001-12-05
PEF 3452
TE3-LIU V1.3
Package Outlines
PRELIMINARY
7
Package Outlines
P-MQFP-44-2
(Plastic Metric Quad Flat Package)
Sorts of Packing
Package outlines for tubes, trays etc. are contained in our
Data Book “Package Information”.
Dimensions in mm
2001-12-05
SMD = Surface Mounted Device
Preliminary Data Sheet
56
PEF 3452
TE3-LIU V1.3
Appendix
PRELIMINARY
8
Appendix
8.1
Cable Characteristics
Cable characteristics are defined in ANSI T1.102 as shown below.
Office Cable Loss (450 ft. coaxial)
14
12
10
8
6
4
2
0
1
10
100
Frequency [MHz]
Office Cable Insertion Phase (450 ft. coaxial)
90
80
70
60
50
40
30
20
10
0
1
10
100
Frequency [MHz]
F0105 V1.1
Figure 31
DS3 Cable Characteristics
Preliminary Data Sheet
57
2001-12-05
PEF 3452
TE3-LIU V1.3
Appendix
PRELIMINARY
8.2 Application Example
The following picture shows a typical application circuit (excluding surge protection).
Jitter
Attenuation
Reference
CL
CL
XTAL1/2
VDDRP/VSSRP
VDDR/VSSR
RDOP
RDON
RCLK
LOS
DS3/STS-1/E3
Framer/Mapper
Receive
DS3/STS-1/E3
Receive Line
Interface
RL1/2
Receive Path
Interface
TE3-LIUTM V1.3
DS3/STS-1/E3
Framer/Mapper
Transmit
DS3/STS-1/E3
Transmit Line
Interface
XDIP
XDIN
XCLK
XL1/2
Transmit Path
Interface
VDDXP/VSSXP
VDDX/VSSX
VDD/VSS
REFCLK TEST
Reference
Clock
F0233
N.C. Control Interface
Figure 32
Application Circuit
Preliminary Data Sheet
58
2001-12-05
PEF 3452
TE3-LIU V1.3
PRELIMINARY
Loss of Signal 13
Index
M
A
AIS 11
MIL-Std 883D 38
Ambient temperature 38
AMI 24
ANSI 10, 57
Applications 3, 5
O
Operating Range 39
Output Jitter 28
P
B
Package 54, 56
PLL 42
B3ZS 24
buffer 31
P-MQFP-44-2 56
Power Down 37
Power Supply 14, 38
Pulse Shaper 33
Pulse Template DS3 50
Pulse Template E3 49
C
Cable 57
Clock 8, 10
Clock and Data Recovery 24
crystal 31, 44
Pulse Template STS-1 52
E
R
Edge Selection 12
ESD 38
RCLK 48
Receive Clock
Receive Data
8
8
External Component Values 21, 22
Receive Line Interface 8, 23
Receive Return Loss 23
Receiver 21
H
HDB3 25
Reference Clock 10, 43
Remote Loop 12, 35
Reset 11, 37, 42, 46
I
Input Jitter 27
international standards 10
intrinsic jitter 24
ITU-T 10
S
Supply voltage 39
J
T
JATT 31
TAP Controller 15
Jitter Attenuation 10, 13, 31, 32
Jitter Tolerance 27, 28
Temperature
3
Thermal Behaviour 54
Transmit Clock
Transmit Data
Transmit Line 37
9
9
L
Line Coding 11, 24
Line Monitoring 12, 22
Local Loop 12, 36
Transmit Line Interface 9, 29
Preliminary Data Sheet
59
2001-12-05
PEF 3452
TE3-LIU V1.3
PRELIMINARY
W
wander 27
X
XCLK 47
XTAL 44
Preliminary Data Sheet
60
2001-12-05
Infineon goes for Business Excellence
“Business excellence means intelligent approaches and clearly
defined processes, which are both constantly under review and
ultimately lead to good operating results.
Better operating results and business excellence mean less
idleness and wastefulness for all of us, more professional
success, more accurate information, a better overview and,
thereby, less frustration and more satisfaction.”
Dr. Ulrich Schumacher
h t t p : / / w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG
相关型号：
©2020 ICPDF网 联系我们和版权申明