S29PL064J60BFA070 [INFINEON]
Simultaneous Read/Write;型号: | S29PL064J60BFA070 |
厂家: | Infineon |
描述: | Simultaneous Read/Write |
文件: | 总81页 (文件大小:1673K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
S29PL-J
128-/64-/32-Mbit (8/4/2M × 16-Bit),
3 V, Flash with Enhanced VersatileIO™
S29PL-J, 128-/64-/32-Mbit (8/4/2M
× 16-Bit), 3 V, Flash with Enhanced VersatileIO™
Distinctive Characteristics
Architectural Advantages
Performance Characteristics
■ 128-/64-/32-Mbit Page Mode devices
■ High Performance
❐ Page size of 8 words: Fast page read access from random
locations within the page
❐ Page access times as fast as 20 ns
❐ Random access times as fast as 55 ns
■ Single power supply operation
❐ Full Voltage range: 2.7 to 3.6 V read, erase, and program
operations for battery-powered applications
■ Power consumption (typical values at 10 MHz)
❐ 45 mA active read current
❐ 17 mA program/erase current
■ Simultaneous Read/Write Operation
❐ 0.2 A typical standby mode current
❐ Datacanbecontinuouslyreadfromonebankwhileexecuting
erase/program functions in another bank
Software Features
❐ Zero latency switching from write to read operations
■ Software command-set compatible with JEDEC 42.4 standard
– Backward compatible with Am29F, Am29LV, Am29DL, and
AM29PDL families and MBM29QM/RM, MBM29LV,
MBM29DL, MBM29PDL families
■ FlexBank Architecture (PL127J/PL064J/PL032J)
❐ 4 separate banks, with up to two simultaneous operations
per device
❐ Bank A:
■ CFI (Common Flash Interface) compliant
❐ Provides device-specific information to the system, allowing
host software to easily reconfigure for different Flash devices
PL127J -16 Mbit (4 Kw 8 and 32 Kw 31)
PL064J - 8 Mbit (4 Kw 8 and 32 Kw 15)
PL032J - 4 Mbit (4 Kw 8 and 32 Kw 7)
❐ Bank B:
■ Erase Suspend / Erase Resume
❐ Suspends an erase operation to allow read or program op-
erations in other sectors of same bank
PL127J - 48 Mbit (32 Kw 96)
PL064J - 24 Mbit (32 Kw 48)
PL032J - 12 Mbit (32 Kw 24)
❐ Bank C:
■ Program Suspend / Program Resume
❐ Suspends a program operation to allow read operation from
sectors other than the one being programmed
PL127J - 48 Mbit (32 Kw 96)
PL064J - 24 Mbit (32 Kw 48)
PL032J - 12 Mbit (32 Kw 24)
❐ Bank D:
■ Unlock Bypass Program command
PL127J -16 Mbit (4 Kw 8 and 32 Kw 31)
PL064J - 8 Mbit (4 Kw 8 and 32 Kw 15)
PL032J - 4 Mbit (4 Kw 8 and 32 Kw 7)
■ Reduces overall programming time when issuing multiple
program command sequences
■ Enhanced VersatileI/O (VIO) Control
Hardware Features
❐ Output voltage generated and input voltages tolerated on all
control inputs and I/Os is determined by the voltage on the
VIO pin
❐ VIO options at 1.8 V and 3 V I/O for PL127J devices
❐ 3V VIO for PL064J and PL032J devices
■ Ready/Busy# pin (RY/BY#)
❐ Provides a hardware method of detecting program or erase
cycle completion
■ Hardware reset pin (RESET#)
■ Secured Silicon Sector region
❐ Hardware method to reset the device to reading array data
❐ Up to 128 words accessible through a command sequence
❐ Up to 64 factory-locked words
❐ Up to 64 customer-lockable words
■ WP#/ ACC (Write Protect/Acceleration) input
❐ At VIL, hardware level protection for the first and last two 4K
word sectors.
❐ At VIH, allows removal of sector protection
❐ At VHH, provides accelerated programming in a factory set-
ting
■ Both top and bottom boot blocks in one device
■ Manufactured on 110-nm process technology
■ Data Retention: 20 years typical
■ Persistent Sector Protection
❐ A command sector protection method to lock combinations
of individual sectors and sector groups to prevent program
or erase operations within that sector
■ Cycling Endurance: 1 million cycles per sector typical
❐ Sectors can be locked and unlocked in-system at VCC level
Cypress Semiconductor Corporation
Document Number: 002-00615 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 20, 2019
S29PL-J
■ Password Sector Protection
■ Package Options
❐ A sophisticated sector protection method to lock combina-
tions of individual sectors and sector groups to prevent pro-
gram or erase operations within that sector using a user-de-
fined 64-bit password
❐ 11 8 mm, 80-ball Fine-pitch BGA (PL127J) (VBG080)
8.15 6.15 mm, 48-ball Fine pitch BGA (PL064J/PL032J)
(VBK048)
❐ 20 14 mm, 56-pin TSOP (PL127J) (TS056)
Document Number: 002-00615 Rev. *F
Page 2 of 80
S29PL-J
Contents
1.
General Description..................................................... 4
13.5 Temporary Sector Unprotect......................................... 37
13.6 Secured Silicon Sector Flash Memory Region ............. 37
13.7 Hardware Data Protection............................................. 39
2.
Simultaneous Read/Write Operation
with Zero Latency ........................................................ 4
14. Common Flash Memory Interface (CFI).................... 40
2.1 Page Mode Features ..................................................... 5
2.2 Standard Flash Memory Features ................................. 5
15. Command Definitions................................................. 43
15.1 Reading Array Data ...................................................... 43
15.2 Reset Command........................................................... 43
15.3 Autoselect Command Sequence .................................. 43
15.4 Enter/Exit Secured Silicon Sector
3.
Ordering Information................................................... 6
3.1 Valid Combinations - Standard ...................................... 7
3.2 Valid Combinations - Automotive Grade
/ AEC-Q100.................................................................... 8
Command Sequence.................................................... 44
15.5 Word Program Command Sequence............................ 44
15.6 Chip Erase Command Sequence ................................. 46
15.7 Sector Erase Command Sequence .............................. 46
15.8 Erase Suspend/Erase Resume Commands ................. 47
15.9 Program Suspend/Program Resume Commands ........ 48
15.10Command Definitions Tables ....................................... 49
4.
5.
6.
Product Selector Guide............................................... 9
Block Diagram.............................................................. 9
Simultaneous Read/Write Block Diagram ............... 10
7.
Connection Diagrams................................................ 11
7.1 Special Package Handling Instructions........................ 11
7.2 80-Ball Fine-Pitch BGA—PL127J ................................ 11
7.3 64-Ball Fine-Pitch BGA—PL127J ................................ 12
7.4 48-Ball Fine-Pitch BGA, PL064J and PL032J .............. 13
7.5 56-Pin TSOP 20 x 14 mm............................................ 14
7.6 56-Ball Fine-Pitch Ball Grid Array,
16. Write Operation Status............................................... 52
16.1 DQ7: Data# Polling....................................................... 52
16.2 RY/BY#: Ready/Busy#.................................................. 53
16.3 DQ6: Toggle Bit I .......................................................... 53
16.4 DQ2: Toggle Bit II ......................................................... 55
16.5 Reading Toggle Bits DQ6/DQ2..................................... 55
16.6 DQ5: Exceeded Timing Limits ...................................... 55
16.7 DQ3: Sector Erase Timer.............................................. 56
PL064J and PL032J..................................................... 15
8.
9.
Pin Description........................................................... 16
Logic Symbol ............................................................. 17
10. Device Bus Operations.............................................. 18
10.1 Requirements for Reading Array Data......................... 18
10.2 Simultaneous Read/Write Operation ........................... 19
10.3 Writing Commands/Command Sequences.................. 19
10.4 Standby Mode.............................................................. 20
10.5 Automatic Sleep Mode................................................. 20
10.6 RESET#: Hardware Reset Pin..................................... 20
10.7 Output Disable Mode ................................................... 20
10.8 Autoselect Mode .......................................................... 27
10.9 Selecting a Sector Protection Mode............................. 29
17. Absolute Maximum Ratings....................................... 57
18. Operating Ranges....................................................... 58
19. DC Characteristics...................................................... 59
20. AC Characteristics...................................................... 60
20.1 Test Conditions............................................................. 60
20.2 Switching Waveforms ................................................... 61
20.3 Read Operations........................................................... 61
20.4 Reset ............................................................................ 63
20.5 Erase/Program Operations........................................... 64
20.6 Timing Diagrams........................................................... 65
11. Sector Protection....................................................... 31
11.1 Persistent Sector Protection ........................................ 31
11.2 Password Sector Protection......................................... 31
11.3 WP# Hardware Protection ........................................... 31
11.4 Selecting a Sector Protection Mode............................. 31
21. Protect/Unprotect........................................................ 68
21.1 Controlled Erase Operations......................................... 69
22. Pin Capacitance.......................................................... 72
22.1 BGA Pin Capacitance................................................... 72
22.2 TSOP Pin Capacitance................................................. 72
12. Persistent Sector Protection..................................... 32
12.1 Persistent Protection Bit (PPB).................................... 32
12.2 Persistent Protection Bit Lock (PPB Lock)................... 32
12.3 Dynamic Protection Bit (DYB)...................................... 32
12.4 Persistent Sector Protection Mode Locking Bit............ 33
23. Physical Dimensions.................................................. 73
22. Document History Page ............................................. 78
Sales, Solutions, and Legal Information ...........................80
Worldwide Sales and Design Support ............................80
Products .........................................................................80
PSoC® Solutions ...........................................................80
Cypress Developer Community ......................................80
Technical Support ..........................................................80
13. Password Protection Mode....................................... 34
13.1 Password and Password Mode Locking Bit................. 34
13.2 64-bit Password ........................................................... 34
13.3 Write Protect (WP#)..................................................... 35
13.4 High Voltage Sector Protection.................................... 35
Document Number: 002-00615 Rev. *F
Page 3 of 80
S29PL-J
1. General Description
The PL127J/PL064J/PL032J is a 128/128/64/32 Mbit, 3.0 V-only Page Mode and Simultaneous Read/Write Flash memory device
organized as 8/8/4/2 Mwords.
The devices are offered in the following packages:
■ 11 mm 8 mm, 80-ball Fine-pitch BGA standalone (PL127J)
■ 8 mm 11.6 mm, 64-ball Fine-pitch BGA multi-chip compatible (PL127J)
■ 8.15 mm 6.15 mm, 48-ball Fine-pitch BGA standalone (PL064J/PL032J)
■ 7 mm 9 mm, 56-ball Fine-pitch BGA multi-chip compatible (PL064J and PL032J)
■ 20 mm 14 mm, 56-pin TSOP (PL127J)
The word-wide data (x16) appears on DQ15-DQ0. This device can be programmed in-system or in standard EPROM programmers.
A 12.0 V VPP is not required for write or erase operations.
2. Simultaneous Read/Write Operation with Zero Latency
The Simultaneous Read/Write architecture provides simultaneous operation by dividing the memory space into 4 banks, which can
be considered to be four separate memory arrays as far as certain operations are concerned. The device can improve overall system
performance by allowing a host system to program or erase in one bank, then immediately and simultaneously read from another
bank with zero latency (with two simultaneous operations operating at any one time). This releases the system from waiting for the
completion of a program or erase operation, greatly improving system performance.
The device can be organized in both top and bottom sector configurations. The banks are organized as shown in Table 1.
Table 1. Bank Organization
Bank
PL127J Sectors
16 Mbit (4 Kw 8 and 32 Kw 31)
48 Mbit (32 Kw 96)
48 Mbit (32 Kw 96)
16 Mbit (4 Kw x 8 and 32 Kw 31)
PL064J Sectors
8 Mbit (4 Kw 8 and 32 Kw 15)
24 Mbit (32 Kw 48)
24 Mbit (32 Kw 48)
8 Mbit (4 Kw 8 and 32 Kw 15)
PL032J Sectors
4 Mbit (4 Kw 8 and 32 Kw 7)
12 Mbit (32 Kw 24)
12 Mbit (32 Kw 24)
4 Mbit (4 Kw 8 and 32 Kw 7)
A
B
C
D
Document Number: 002-00615 Rev. *F
Page 4 of 80
S29PL-J
2.1
Page Mode Features
The page size is 8 words. After initial page access is accomplished, the page mode operation provides fast read access speed of
random locations within that page.
2.2
Standard Flash Memory Features
The device requires a single 3.0 volt power supply (2.7 V to 3.6 V) for both read and write functions. Internally generated and
regulated voltages are provided for the program and erase operations.
The device is entirely command set compatible with the JEDEC 42.4 single-power-supply Flash standard. Commands are written
to the command register using standard microprocessor write timing. Register contents serve as inputs to an internal state-machine
that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming
and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices.
Device programming occurs by executing the program command sequence. The Unlock Bypass mode facilitates faster programming
times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command
sequence.
The host system can detect whether a program or erase operation is complete by reading the DQ7 (Data# Polling) and DQ6 (toggle)
status bits. After a program or erase cycle has been completed, the device is ready to read array data or accept another command.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other
sectors. The device is fully erased when shipped from the factory.
Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions.
The hardware sector protection feature disables both program and erase operations in any combination of sectors of memory. This
can be achieved in-system or via programming equipment.
The Erase Suspend/Erase Resume feature enables the user to put erase on hold for any period of time to read data from, or program
data to, any sector that is not selected for erasure. True background erase can thus be achieved. If a read is needed from the Secured
Silicon Sector area (One Time Program area) after an erase suspend, then the user must use the proper command sequence to enter
and exit this region.
The Program Suspend/Program Resume feature enables the user to hold the program operation to read data from any sector that
is not selected for programming. If a read is needed from the Secured Silicon Sector area, Persistent Protection area, Dynamic
Protection area, or the CFI area, after a program suspend, then the user must use the proper command sequence to enter and exit
this region.
The device offers two power-saving features. When addresses have been stable for a specified amount of time, the device enters the
automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both
these modes. The device electrically erases all bits within a sector simultaneously via Fowler-Nordheim tunneling. The data is
programmed using hot electron injection.
Document Number: 002-00615 Rev. *F
Page 5 of 80
S29PL-J
3. Ordering Information
The order number (Valid Combination) is formed by a valid combinations of the following:
S29PL-J
XX
XX
X
XX
X
Packing Type: X = 0 or 1 or 2 or 3
0 = Tray
1 = Tube
2 = 7-inch Tape and Reel
3 = 13-inch Tape and Reel
Model Number (Additional Ordering Options): XX = 04 or 05 or 06 or 07 or 08 or 09 or 10
04 = 3.0V V , 80-ball 11 x 8 mm FBGA (VBG080)
IO
05 = 1.8V V , 80-ball 11 x 8 mm FBGA (VBG080)
IO
06 = 3.0V V , 64-ball 8 x 11.6 mm FBGA (VBH064)
IO
07 = 3.0V V , 48-ball 8 x 6 mm FBGA (VBK048)
IO
08 = 3.0V V , 56-pin 20 x 14 mm TSOP (TS056)
IO
09 = 1.8V V , 56-pin 20 x 14 mm TSOP (TS056)
IO
10 = 3.0V V , 56-ball 7 x 9 mm FBGA (VBU056)
IO
Temperature Range: X = W or I
W = Wireless (–25°C to +85°C)
I = Industrial (–40°C to +85°C)
A = Automotive, AEC-Q100 Grade 3 (–40 °C to +85 °C)
Package Type: XX = BF or TF
BF = Fine-Pitch Grid Array (FBGA)
Lead (Pb)-free
TF = Thin Small Outline Package (TSOP) Standard Pinout
Lead (Pb)-free
Clock Speed: XX = 55 or 60 or 65 or 70 or 80
55 = 55 ns (Contact factory for availability)
60 = 60 ns
65 = 65 ns
70 = 70 ns
80 = 80 ns
Device Number/Description
128 Mbit (8M x 16-Bit), 64 Megabit (4M x 16-Bit), 32 Megabit (2M x 16-Bit) CMOS Flash Memory,
Simultaneous-Read/Write, Page-Mode Flash Memory, 3.0 V-only Read, Program, and Erase
Document Number: 002-00615 Rev. *F
Page 6 of 80
S29PL-J
3.1
Valid Combinations - Standard
Valid Combinations list configurations planned to be supported in volume for this device. Contact your local sales office to confirm
availability of specific valid combinations.
Table 2. Standard 128 Mb Products Based on 110 nm Floating Gate Technology
Device Number/
Description
Additional Ordering
Options
Speed (ns)
Package Type
Temperature Range
S29PL127J
S29PL127J
S29PL127J
60, 65, 70
BF, TF
BF
W, I
W, I
W, I
04, 06, 08
80
80
05
09
TF
Table 3. Standard 64 Mb Products Based on 110 nm Floating Gate Technology
Device Number
Speed (ns)
Package Type Temperature Range Additional Ordering Options
/Description
S29PL064J
55, 60, 70
BF
W, I
07, 10
Table 4. Standard 32 Mb Products Based on 110 nm Floating Gate Technology
Device Number
Speed (ns)
Package Type Temperature Range Additional Ordering Options
/Description
S29PL032J
55, 60, 70
BF
W, I
07, 10
Table 5. Standard Valid Combinations for BGA Packages[1]
Order Number
Speed (ns)
55, 60, 65, 70[2]
80
VIO Range
2.7–3.6
PL127J,PL064J, PL032J
PL127J
1.65–1.95
Notes
1. BGA package marking omits leading S29 and packing type designator from ordering part number.
2. 55 ns speed only supported for PL032J and PL127J.
Table 6. Standard Valid Combinations for TSOP Packages[3]
Order Number
Speed (ns)
VIO Range
2.7–3.6
S29PL127J
60, 70
Note
3. TSOP package markings omit packing type designator from ordering part number.
Document Number: 002-00615 Rev. *F
Page 7 of 80
S29PL-J
3.2
Valid Combinations - Automotive Grade / AEC-Q100
The table below lists configurations that are Automotive Grade / AEC-Q100 qualified and are planned to be available in volume. The
table will be updated as new combinations are released. Contact your local sales representative to confirm availability of specific
combinations and to check on newly released combinations. Production Part Approval Process (PPAP) support is only provided for
AEC-Q100 grade products. Products to be used in end-use applications that require ISO/TS-16949 compliance must be AEC-Q100
grade products in combination with PPAP. Non–AEC-Q100 grade products are not manufactured or documented in full compliance
with ISO/TS-16949 requirements. AEC-Q100 grade products are also offered without PPAP support for end-use applications that do
not require ISO/TS-16949 compliance.
Table 7. Automotive 128 Mb Products Based on 110 nm Floating Gate Technology
Device Number/
Description
Additional Ordering
Options
Speed (ns)
Package Type
Temperature Range
S29PL127J
S29PL127J
S29PL127J
60, 65, 70
BF, TF
BF
A
A
A
04, 06, 08
80
80
05
09
TF
Table 8. Automotive 64 Mb Products Based on 110 nm Floating Gate Technology
Device Number
Speed (ns)
Package Type Temperature Range Additional Ordering Options
/Description
S29PL064J
55, 60, 70
BF
A
07, 10
Table 9. Automotive 32 Mb Products Based on 110 nm Floating Gate Technology
Device Number
Speed (ns)
Package Type Temperature Range Additional Ordering Options
/Description
S29PL032J
55, 60, 70
BF
A
07, 10
Table 10. Automotive Valid Combinations for BGA Packages[4]
Order Number
PL127J,PL064J, PL032J
PL127J
Speed (ns)
55, 60, 65, 70[5]
80
VIO Range
2.7–3.6
1.65–1.95
Notes
4. BGA package marking omits leading S29 and packing type designator from ordering part number.
5. 55 ns speed only supported for PL032J and PL127J.
Table 11. Automotive Valid Combinations for TSOP Packages[6]
Order Number
Speed (ns)
VIO Range
2.7–3.6
S29PL127J
60, 70
Note
6. TSOP package markings omit packing type designator from ordering part number.
Document Number: 002-00615 Rev. *F
Page 8 of 80
S29PL-J
4. Product Selector Guide
Part Number
S29PL032J/S29PL064J/S29PL0127J
V
CC,VIO = 2.7 V – 3.6 V
VCC = 2.7 V – 3.6 V,
IO = 1.65 V – 1.95 V
(PL127J)
Max Access Time, ns (tACC
Max CE# Access, ns (tCE
Max Page Access, ns (tPACC
55[7]
60
65
—
70
—
Speed Option
V
—
—
—
80
)
55[7]
20[7]
60
25
65
80
30
70
30
)
)
Max OE# Access, ns (tOE
)
Note
7. 55 ns speed bin only supported for PL032J and PL064J.
5. Block Diagram
DQ15–DQ0
RY/BY#
V
CC
V
SS
Sector
Switches
V
IO
Input/Output
Buffers
RESET#
WE#
Erase Voltage
Generator
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
Data Latch
Y-Gating
Y-Decoder
X-Decoder
V
CC
Detector
Timer
Amax–A3
Cell Matrix
A2–A0
Notes
8. RY/BY# is an open drain output.
9. Amax = A22 (PL127J), A21 (PL064J), A20 (PL032J).
Document Number: 002-00615 Rev. *F
Page 9 of 80
S29PL-J
6. Simultaneous Read/Write Block Diagram
V
CC
V
SS
OE#
Mux
Bank A
Bank A Address
Amax–A0
X-Decoder
Bank B Address
RY/BY#
Bank B
X-Decoder
Amax–A0
RESET#
STATE
CONTROL
&
COMMAND
REGISTER
Status
WE#
DQ15–DQ0
CE#
WP#/ACC
Control
Mux
X-Decoder
Bank C
DQ0–DQ15
Bank C Address
Bank D Address
X-Decoder
Bank D
Amax–A0
Mux
Note
10. Amax = A22 (PL127J), A21 (PL064J), A20 (PL032J).
Document Number: 002-00615 Rev. *F
Page 10 of 80
S29PL-J
7. Connection Diagrams
7.1
Special Package Handling Instructions
7.1.1 TSOP, BGA, PDIP, SSOP, and PLCC Packages
Special handling is required for Flash Memory products in molded packages.
The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged
periods of time.
7.1.2 FBGA Packages
Special handling is required for Flash Memory products in FBGA packages.
Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data
integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time.
7.2
80-Ball Fine-Pitch BGA—PL127J
Figure 1. 80-Ball Fine-Pitch BGA, Top View, Balls Facing Down—PL127J
A8
NC
B8
NC
C8
NC
D8
E8
F8
G8
H8
NC
J8
K8
NC
L8
M8
NC
A22
NC
V
IO
V
SS
NC
NC
A7
NC
B7
NC
C7
D7
E7
F7
G7
H7
NC
J7
K7
L7
M7
NC
A13
A12
A14
A15
A16
DQ15
V
SS
NC
C6
A9
D6
A8
E6
F6
G6
H6
J6
K6
A10
A11
DQ7
DQ14
DQ13
DQ6
C5
D5
E5
F5
G5
H5
J5
K5
WE#
RESET#
A21
A19
DQ5
DQ12
V
DQ4
CC
C4
D4
E4
F4
G4
H4
J4
K4
RY/BY# WP#/ACC
A18
A20
DQ2
DQ10
DQ11
DQ3
C3
A7
D3
E3
A6
F3
A5
G3
H3
J3
K3
A17
DQ0
DQ8
DQ9
DQ1
A2
NC
B2
NC
C2
A3
D2
A4
E2
A2
F2
A1
G2
A0
H2
J2
K2
L2
M2
NC
CE#
OE#
V
NC
SS
A1
NC
B1
NC
C1
NC
D1
NC
E1
F1
G1
NC
H1
J1
K1
NC
L1
M1
NC
NC
NC
V
IO
NC
NC
Document Number: 002-00615 Rev. *F
Page 11 of 80
S29PL-J
7.3
64-Ball Fine-Pitch BGA—PL127J
Figure 2. 64-Ball Fine-Pitch BGA, Top View, Balls Facing Down—PL127J
A1
NC
A10
NC
B5
B6
RFU
RFU
C3
A7
C4
C5
C6
C7
A8
C8
A11
RFU
WP#/ACC WE#
D2
A3
D3
A6
D4
D5
D6
D7
D8
D9
A12
A15
RFU
RESET# RFU
A19
E2
A2
E3
A5
E4
E5
E6
E7
A9
E8
E9
RY/BY # A20
A13
A21
A18
F2
A1
F3
A4
F4
F7
F8
F9
A17
A10
A14
A22
G2
A0
G3
G4
G7
G8
G9
VSS
DQ1
DQ6
RFU
A16
H2
H3
H4
H5
H6
H7
H8
H9
CE#
OE#
DQ9
DQ3
DQ4
DQ13
DQ15
VCC
J2
J3
J4
DQ10
K4
J5
VCC
K5
J6
J7
DQ12
K7
J8
J9
RFU
DQ0
K3
RFU
K6
DQ7
K8
VSS
DQ8
DQ2
DQ11
RFU
DQ5
DQ14
L5
L6
RFU
RFU
M1
NC
M10
NC
Document Number: 002-00615 Rev. *F
Page 12 of 80
S29PL-J
7.4
48-Ball Fine-Pitch BGA, PL064J and PL032J
Figure 3. 48-Ball Fine-Pitch BGA, Top View, Balls Facing Down—PL064J—PL032J: C4(A21)=NC
A6
B6
C6
D6
E6
F6
G6
H6
VSS
A13
A12
A14
A15
A16
NC
DQ15
A5
A9
B5
A8
C5
D5
E5
F5
G5
H5
A10
A11
DQ7
DQ14
DQ13
DQ6
A4
B4
C4
D4
E4
F4
G4
H4
WE#
RESET#
A21
A19
DQ5
DQ12
V
DQ4
CC
A3
B3
C3
D3
E3
F3
G3
H3
RY/BY# WP#/ACC
A18
A20
DQ2
DQ10
DQ11
DQ3
A2
A7
B2
C2
A6
D2
A5
E2
F2
G2
H2
A17
DQ0
DQ8
DQ9
DQ1
A1
A3
B1
A4
C1
A2
D1
A1
E1
A0
F1
G1
H1
CE#
OE#
VSS
Document Number: 002-00615 Rev. *F
Page 13 of 80
S29PL-J
7.5
56-Pin TSOP 20 x 14 mm
Figure 4. 56-Pin TSOP 20 x 14 mm Configuration—PL127J
RESET#
RY/BY#
A0
1
WP#/ACC
WE#
NC
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
2
3
A1
4
A22
A2
5
A21
A3
6
A20
A4
7
OE#
NC
A5
8
VCC
9
CE#
VSS
DQ0
DQ1
DQ2
DQ3
VSS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
DQ15
DQ14
DQ13
DQ12
VSS
VCC
DQ4
DQ5
DQ6
DQ7
VSS
NC
VCC
DQ11
DQ10
DQ9
DQ8
VCC
A6
A19
A7
A18
A8
A17
A9
A16
A10
A11
A12
A15
A14
A13
For this family of products, a single multi-chip compatible package (TSOP) is offered for each density to allow both standalone and
multi-chip qualification using a single, adaptable package. This new methodology allows package standardization resulting in faster
development. The multi-chip compatible package includes all the pins required for standalone device operation and verification. In
addition, extra pins are included for insertion of common data storage or logic devices to be used for multi-chip products. If a
standalone device is required, the extra multi-chip specific pins are not connected and the standalone device operates normally. The
multi-chip compatible package sizes were chosen to serve the largest number of combinations possible. There are only a few cases
where a larger package size would be required to accommodate the multi-chip combination. This multi-chip compatible package set
does not allow for direct package migration from the Am29BDS128H, Am29BDS128G, Am29BDS640G products, which use legacy
standalone packages.
Document Number: 002-00615 Rev. *F
Page 14 of 80
S29PL-J
7.6
56-Ball Fine-Pitch Ball Grid Array, PL064J and PL032J
Figure 5. 56-ball Fine-Pitch BGA, Top View, Balls Facing Down—PL064J and PL032J
A2
A7
B2
A6
C2
A3
RFU
B3
A4
WP/ACC
B4
A5
WE#
B5
A6
A8
A7
A11
B7
B1
A3
C1
A2
D1
A1
B6
B8
A15
C8
RFU
C3
RST#
C4
RFU
C5
A19
C6
A12
C7
A5
D2
A4
A18
D3
RY/BY#
A20
A9
D6
A13
D7
A21
D8
A17
A10
A14
RFU
E1
A0
E2
E3
E6
E7
E8
VSS
DQ1
DQ6
RFU
A16
F1
F2
F3
F4
F5
F6
F7
F8
CE1#f
OE#
DQ9
DQ3
DQ4
DQ13
DQ15
RFU
G8
G1
G2
G3
DQ10
H3
G4
G5
G6
G7
RFU
DQ0
VCCf
RFU
DQ12
DQ7
VSS
H7
H2
H4
H6
H5
DQ14
DQ8
DQ2
DQ5
DQ11
RFU
Document Number: 002-00615 Rev. *F
Page 15 of 80
S29PL-J
8. Pin Description
Table 12. Pin Description
Pin Name
Description
Amax–A0
DQ15–DQ0
CE#
Address bus
16-bit data inputs/outputs/float
Chip Enable Inputs
Output Enable Input
Write Enable
OE#
WE#
VSS
Device Ground
Not Connected. No device internal signal is connected to the package connector nor is there any future
plan to use the connector for a signal. The connection may safely be used for routing space for a signal on
a Printed Circuit Board (PCB).
NC
RFU
Reserved for Future Use. Not currently connected internally but the pin/ball location should be left uncon-
nected and unused by PCB routing channel for future compatibility. The pin/ball may be used by a signal
in the future.
Ready/Busy output and open drain.
When RY/BY#= VIH, the device is ready to accept read operations and commands. When RY/BY#= VOL,
RY/BY#
the device is either executing an embedded algorithm or the device is executing a hardware reset operation.
Write Protect/Acceleration Input.
When WP#/ACC= VIL, the highest and lowest two 4K-word sectors are write protected regardless of other
sector protection configurations. When WP#/ACC= VIH, these sector are unprotected unless the DYB or
PPB is programmed. When WP#/ACC= VHH, program and erase operations are accelerated.
WP#/ACC
VIO
Input/Output Buffer Power Supply
(1.65 V to 1.95 V (for PL127J) or 2.7 V to 3.6 V (for all PLxxxJ devices))
VCC
Chip Power Supply (2.7 V to 3.6 V or 2.7 to 3.3 V)
Hardware Reset Pin
RESET#
Note
11. Amax = A22 (PL127J), A21 (PL064J), A20 (PL032J).
Document Number: 002-00615 Rev. *F
Page 16 of 80
S29PL-J
9. Logic Symbol
max+1
Amax–A0
16
DQ15–DQ0
CE#
OE#
WE#
WP#/ACC
RESET#
RY/BY#
V
(V
)
CCQ
IO
Document Number: 002-00615 Rev. *F
Page 17 of 80
S29PL-J
10. Device Bus Operations
This section describes the requirements and use of the device bus operations, which are initiated through the internal command
register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the
commands, along with the address and data information needed to execute the command. The contents of the register serve as inputs
to the internal state machine. The state machine outputs dictate the function of the device. Table 13 lists the device bus operations,
the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in
further detail.
Table 13. PL127J Device Bus Operations
Addresses
(Amax–A0)
Operation
CE#
OE#
WE#
RESET# WP#/ACC
DQ15–DQ0
Read
L
L
H
X
H
X
H
L
H
X
X[13]
X[13]
X
AIN
AIN
X
DOUT
DIN
Write
L
H
Standby
VIO0.3 V
X
H
X
VIO 0.3 V
High-Z
High-Z
High-Z
Output Disable
Reset
L
H
L
X
X
X
X
Temporary Sector Unprotect
(High Voltage)
X
X
X
VID
X
AIN
DIN
Legend
L = Logic Low = V , H = Logic High = V , V = 11.5–12.5 V, V = 8.5–9.5 V, X = Don’t Care, SA = Sector Address, A = Address In, D = Data In, D = Data Out
OUT
IL
IH
ID
HH
IN
IN
10.1 Requirements for Reading Array Data
To read array data from the outputs, the system must drive the OE# and appropriate CE# pins to VIL. CE# is the power control. OE#
is the output control and gates array data to the output pins. WE# should remain at VIH.
The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious
alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data
outputs. Each bank remains enabled for read access until the command register contents are altered.
Refer to Table 34 on page 61 for timing specifications and to Figure 16 on page 62 for the timing diagram. ICC1 in the DC Character-
istics table represents the active current specification for reading array data.
10.1.1 Random Read (Non-Page Read)
Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the
delay from the stable addresses and stable CE# to valid data at the output inputs. The output enable access time is the delay from
the falling edge of the OE# to valid data at the output inputs (assuming the addresses have been stable for at least tACC–tOE time).
10.1.2 Page Mode Read
The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides
faster read access speed for random locations within a page. Address bits Amax–A3 select an 8 word page, and address bits A2–A0
select a specific word within that page. This is an asynchronous operation with the microprocessor supplying the specific word location.
The random or initial page access is tACC or tCE and subsequent page read accesses (as long as the locations specified by the
microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted (=VIH), the reassertion of CE# for subsequent
access has access time of tACC or tCE. Here again, CE# selects the device and OE# is the output control and should be used to gate
data to the output inputs if the device is selected. Fast page mode accesses are obtained by keeping Amax–A3 constant and changing
A2–A0 to select the specific word within that page.
Notes
12. The sector protect and sector unprotect functions may also be implemented via programming equipment. See High Voltage Sector Protection on page 35.
13. WP#/ACC must be high when writing to upper two and lower two sectors.
Document Number: 002-00615 Rev. *F
Page 18 of 80
S29PL-J
Table 14. Page Select
Word
A2
0
A1
0
A0
0
Word 0
Word 1
Word 2
Word 3
Word 4
Word 5
Word 6
Word 7
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
10.2 Simultaneous Read/Write Operation
In addition to the conventional features (read, program, erase-suspend read, erase-suspend program, and program-suspend read),
the device is capable of reading data from one bank of memory while a program or erase operation is in progress in another bank of
memory (simultaneous operation). The bank can be selected by bank addresses (PL127J: A22–A20, PL064J: A21–A19, PL032J:
A20–A18) with zero latency.
The simultaneous operation can execute multi-function mode in the same bank.
Table 15. Bank Select
Bank
PL127J: A22–A20, PL064J: A21–A19, PL032J: A20–A18
Bank A
Bank B
Bank C
Bank D
000
001, 010, 011
100, 101, 110
111
10.3 Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the
system must drive WE# and CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facilitate faster programming. Once a bank enters the Unlock Bypass mode, only
two write cycles are required to program a word, instead of four. Section 15.5 Word Program Command Sequence on page 44 has
details on programming data to the device using both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 15 indicates the set of address space that each
sector occupies. A “bank address” is the set of address bits required to uniquely select a bank. Similarly, a “sector address” refers to
the address bits required to uniquely select a sector. Section 15. Command Definitions on page 43 has details on erasing a sector or
the entire chip, or suspending/resuming the erase operation.
I
CC2 in the Section 19. DC Characteristics on page 59 represents the active current specification for the write mode. See the timing
specification tables and timing diagrams in section Section 20.4 Reset on page 63 for write operations.
10.3.1 Accelerated Program Operation
The device offers accelerated program operations through the ACC function. This function is primarily intended to allow faster
manufacturing throughput at the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects
any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would
use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns
the device to normal operation. Note that VHH must not be asserted on WP#/ACC for operations other than accelerated programming,
or device damage may result. In addition, the WP#/ACC pin should be raised to VCC when not in use. That is, the WP#/ACC pin should
not be left floating or unconnected; inconsistent behavior of the device may result.
Document Number: 002-00615 Rev. *F
Page 19 of 80
S29PL-J
10.3.2 Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect
codes from the internal register (which is separate from the memory array) on DQ15–DQ0. Standard read cycle timings apply in this
mode. Refer to the Table 19 on page 27 and Section 15.3 Autoselect Command Sequence on page 43 for more information.
10.4 Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption
is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input.
The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VIO ± 0.3 V. (Note that this is a more
restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VIO ± 0.3 V, the device will be in the standby
mode, but the standby current will be greater. The device requires standard access time (tCE) for read access when the device is in
either of these standby modes, before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until the operation is completed.
ICC3 in Section 19. DC Characteristics on page 59 represents the CMOS standby current specification.
10.5 Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses
remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address
access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to
the system. Note that during automatic sleep mode, OE# must be at VIH before the device reduces current to the stated sleep mode
specification. ICC5 in Section 19. DC Characteristics on page 59 represents the automatic sleep mode current specification.
10.6 RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for
at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write
commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The
operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current
(ICC4). If RESET# is held at VIL but not within VSS±0.3 V, the standby current will be greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the
system to read the boot-up firmware from the Flash memory.
If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is
complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether
the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the
reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the
RESET# pin returns to VIH.
Refer to the tables in Section 20. AC Characteristics on page 60 for RESET# parameters and to Figure 18 on page 63 for the timing
diagram.
10.7 Output Disable Mode
When the OE# input is at VIH, output from the device is disabled. The output pins (except for RY/BY#) are placed in the highest
Impedance state.
Document Number: 002-00615 Rev. *F
Page 20 of 80
S29PL-J
Table 16. PL127J Sector Architecture (Continued)
Table 16. PL127J Sector Architecture
SectorAddress SectorSize
Bank
Sector
Address Range (x16)
(A22-A12)
(Kwords)
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
SectorAddress SectorSize
Bank
Sector
Address Range (x16)
(A22-A12)
(Kwords)
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
SA71
SA72
SA73
SA74
SA75
SA76
SA77
SA78
SA79
SA80
SA81
SA82
SA83
SA84
SA85
SA86
SA87
SA88
SA89
00100110XXX
00100111XXX
00101000XXX
00101001XXX
00101010XXX
00101011XXX
00101100XXX
00101101XXX
00101110XXX
00101111XXX
00110000XXX
00110001XXX
00110010XXX
00110011XXX
00110100XXX
00110101XXX
00110110XXX
00110111XXX
00111000XXX
00111001XXX
00111010XXX
00111011XXX
00111100XXX
00111101XXX
00111110XXX
00111111XXX
01000000XXX
01000001XXX
01000010XXX
01000011XXX
01000100XXX
01000101XXX
01000110XXX
01000111XXX
01001000XXX
01001001XXX
01001010XXX
01001011XXX
01001100XXX
01001101XXX
01001110XXX
01001111XXX
01010000XXX
01010001XXX
01010010XXX
130000h–137FFFh
138000h–13FFFFh
140000h–147FFFh
148000h–14FFFFh
150000h–157FFFh
158000h–15FFFFh
160000h–167FFFh
168000h–16FFFFh
170000h–177FFFh
178000h–17FFFFh
180000h–187FFFh
188000h–18FFFFh
190000h–197FFFh
198000h–19FFFFh
1A0000h–1A7FFFh
1A8000h–1AFFFFh
1B0000h–1B7FFFh
1B8000h–1BFFFFh
1C0000h–1C7FFFh
1C8000h–1CFFFFh
1D0000h–1D7FFFh
1D8000h–1DFFFFh
1E0000h–1E7FFFh
1E8000h–1EFFFFh
1F0000h–1F7FFFh
1F8000h–1FFFFFh
200000h–207FFFh
208000h–20FFFFh
210000h–217FFFh
218000h–21FFFFh
220000h–227FFFh
228000h–22FFFFh
230000h–237FFFh
238000h–23FFFFh
240000h–247FFFh
248000h–24FFFFh
250000h–257FFFh
258000h–25FFFFh
260000h–267FFFh
268000h–26FFFFh
270000h–277FFFh
278000h–27FFFFh
280000h–287FFFh
288000h–28FFFFh
290000h–297FFFh
SA0
SA1
00000000000
00000000001
00000000010
00000000011
00000000100
00000000101
00000000110
00000000111
00000001XXX
00000010XXX
00000011XXX
00000100XXX
00000101XXX
00000110XXX
00000111XXX
00001000XXX
00001001XXX
00001010XXX
00001011XXX
00001100XXX
00001101XXX
00001110XXX
00001111XXX
00010000XXX
00010001XXX
00010010XXX
00010011XXX
00010100XXX
00010101XXX
00010110XXX
00010111XXX
00011000XXX
00011001XXX
00011010XXX
00011011XXX
00011100XXX
00011101XXX
00011110XXX
00011111XXX
00100000XXX
00100001XXX
00100010XXX
00100011XXX
00100100XXX
00100101XXX
4
000000h–000FFFh
001000h–001FFFh
002000h–002FFFh
003000h–003FFFh
004000h–004FFFh
005000h–005FFFh
006000h–006FFFh
007000h–007FFFh
008000h–00FFFFh
010000h–017FFFh
018000h–01FFFFh
020000h–027FFFh
028000h–02FFFFh
030000h–037FFFh
038000h–03FFFFh
040000h–047FFFh
048000h–04FFFFh
050000h–057FFFh
058000h–05FFFFh
060000h–067FFFh
068000h–06FFFFh
070000h–077FFFh
078000h–07FFFFh
080000h–087FFFh
088000h–08FFFFh
090000h–097FFFh
098000h–09FFFFh
0A0000h–0A7FFFh
0A8000h–0AFFFFh
0B0000h–0B7FFFh
0B8000h–0BFFFFh
0C0000h–0C7FFFh
0C8000h–0CFFFFh
0D0000h–0D7FFFh
0D8000h–0DFFFFh
0E0000h–0E7FFFh
0E8000h–0EFFFFh
0F0000h–0F7FFFh
0F8000h–0FFFFFh
100000h–107FFFh
108000h–10FFFFh
110000h–117FFFh
118000h–11FFFFh
120000h–127FFFh
128000h–12FFFFh
4
SA2
4
SA3
4
SA4
4
SA5
4
SA6
4
SA7
4
SA8
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
SA9
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
SA43
SA44
Document Number: 002-00615 Rev. *F
Page 21 of 80
S29PL-J
Table 16. PL127J Sector Architecture (Continued)
Table 16. PL127J Sector Architecture (Continued)
SectorAddress SectorSize
SectorAddress SectorSize
Bank
Sector
Address Range (x16)
Bank
Sector
Address Range (x16)
(A22-A12)
(Kwords)
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
(A22-A12)
(Kwords)
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
SA90
SA91
01010011XXX
01010100XXX
01010101XXX
01010110XXX
01010111XXX
01011000XXX
01011001XXX
01011010XXX
01011011XXX
01011100XXX
01011101XXX
01011110XXX
01011111XXX
01100000XXX
01100001XXX
01100010XXX
01100011XXX
01100100XXX
01100101XXX
01100110XXX
01100111XXX
01101000XXX
01101001XXX
01101010XXX
01101011XXX
01101100XXX
01101101XXX
01101110XXX
01101111XXX
01110000XXX
01110001XXX
01110010XXX
01110011XXX
01110100XXX
01110101XXX
01110110XXX
01110111XXX
01111000XXX
01111001XXX
01111010XXX
01111011XXX
01111100XXX
01111101XXX
01111110XXX
01111111XXX
298000h–29FFFFh
2A0000h–2A7FFFh
2A8000h–2AFFFFh
2B0000h–2B7FFFh
2B8000h–2BFFFFh
2C0000h–2C7FFFh
2C8000h–2CFFFFh
2D0000h–2D7FFFh
2D8000h–2DFFFFh
2E0000h–2E7FFFh
2E8000h–2EFFFFh
2F0000h–2F7FFFh
2F8000h–2FFFFFh
300000h–307FFFh
308000h–30FFFFh
310000h–317FFFh
318000h–31FFFFh
320000h–327FFFh
328000h–32FFFFh
330000h–337FFFh
338000h–33FFFFh
340000h–347FFFh
348000h–34FFFFh
350000h–357FFFh
358000h–35FFFFh
360000h–367FFFh
368000h–36FFFFh
370000h–377FFFh
378000h–37FFFFh
380000h–387FFFh
388000h–38FFFFh
390000h–397FFFh
398000h–39FFFFh
3A0000h–3A7FFFh
3A8000h–3AFFFFh
3B0000h–3B7FFFh
3B8000h–3BFFFFh
3C0000h–3C7FFFh
3C8000h–3CFFFFh
3D0000h–3D7FFFh
3D8000h–3DFFFFh
3E0000h–3E7FFFh
3E8000h–3EFFFFh
3F0000h–3F7FFFh
3F8000h–3FFFFFh
SA135
SA136
SA137
SA138
SA139
SA140
SA141
SA142
SA143
SA144
SA145
SA146
SA147
SA148
SA149
SA150
SA151
SA152
SA153
SA154
SA155
SA156
SA157
SA158
SA159
SA160
SA161
SA162
SA163
SA164
SA165
SA166
SA167
SA168
SA169
SA170
SA171
SA172
SA173
SA174
SA175
SA176
SA177
SA178
SA179
10000000XXX
10000001XXX
10000010XXX
10000011XXX
10000100XXX
10000101XXX
10000110XXX
10000111XXX
10001000XXX
10001001XXX
10001010XXX
10001011XXX
10001100XXX
10001101XXX
10001110XXX
10001111XXX
10010000XXX
10010001XXX
10010010XXX
10010011XXX
10010100XXX
10010101XXX
10010110XXX
10010111XXX
10011000XXX
10011001XXX
10011010XXX
10011011XXX
10011100XXX
10011101XXX
10011110XXX
10011111XXX
10100000XXX
10100001XXX
10100010XXX
10100011XXX
10100100XXX
10100101XXX
10100110XXX
10100111XXX
10101000XXX
10101001XXX
10101010XXX
10101011XXX
10101100XXX
400000h–407FFFh
408000h–40FFFFh
410000h–417FFFh
418000h–41FFFFh
420000h–427FFFh
428000h–42FFFFh
430000h–437FFFh
438000h–43FFFFh
440000h–447FFFh
448000h–44FFFFh
450000h–457FFFh
458000h–45FFFFh
460000h–467FFFh
468000h–46FFFFh
470000h–477FFFh
478000h–47FFFFh
480000h–487FFFh
488000h–48FFFFh
490000h–497FFFh
498000h–49FFFFh
4A0000h–4A7FFFh
4A8000h–4AFFFFh
4B0000h–4B7FFFh
4B8000h–4BFFFFh
4C0000h–4C7FFFh
4C8000h–4CFFFFh
4D0000h–4D7FFFh
4D8000h–4DFFFFh
4E0000h–4E7FFFh
4E8000h–4EFFFFh
4F0000h–4F7FFFh
4F8000h–4FFFFFh
500000h–507FFFh
508000h–50FFFFh
510000h–517FFFh
518000h–51FFFFh
520000h–527FFFh
528000h–52FFFFh
530000h–537FFFh
538000h–53FFFFh
540000h–547FFFh
548000h–54FFFFh
550000h–557FFFh
558000h–15FFFFh
560000h–567FFFh
SA92
SA93
SA94
SA95
SA96
SA97
SA98
SA99
SA100
SA101
SA102
SA103
SA104
SA105
SA106
SA107
SA108
SA109
SA110
SA111
SA112
SA113
SA114
SA115
SA116
SA117
SA118
SA119
SA120
SA121
SA122
SA123
SA124
SA125
SA126
SA127
SA128
SA129
SA130
SA131
SA132
SA133
SA134
Document Number: 002-00615 Rev. *F
Page 22 of 80
S29PL-J
Table 16. PL127J Sector Architecture (Continued)
Table 16. PL127J Sector Architecture (Continued)
SectorAddress SectorSize
SectorAddress SectorSize
Bank
Sector
Address Range (x16)
Bank
Sector
Address Range (x16)
(A22-A12)
(Kwords)
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
(A22-A12)
(Kwords)
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
4
SA180
SA181
SA182
SA183
SA184
SA185
SA186
SA187
SA188
SA189
SA190
SA191
SA192
SA193
SA194
SA195
SA196
SA197
SA198
SA199
SA200
SA201
SA202
SA203
SA204
SA205
SA206
SA207
SA208
SA209
SA210
SA211
SA212
SA213
SA214
SA215
SA216
SA217
SA218
SA219
SA220
SA221
SA222
SA223
SA224
10101101XXX
10101110XXX
10101111XXX
10110000XXX
10110001XXX
10110010XXX
10110011XXX
10110100XXX
10110101XXX
10110110XXX
10110111XXX
10111000XXX
10111001XXX
10111010XXX
10111011XXX
10111100XXX
10111101XXX
10111110XXX
10111111XXX
11000000XXX
11000001XXX
11000010XXX
11000011XXX
11000100XXX
11000101XXX
11000110XXX
11000111XXX
11001000XXX
11001001XXX
11001010XXX
11001011XXX
11001100XXX
11001101XXX
11001110XXX
11001111XXX
11010000XXX
11010001XXX
11010010XXX
11010011XXX
11010100XXX
11010101XXX
11010110XXX
11010111XXX
11011000XXX
11011001XXX
568000h–56FFFFh
570000h–577FFFh
578000h–57FFFFh
580000h–587FFFh
588000h–58FFFFh
590000h–597FFFh
598000h–59FFFFh
5A0000h–5A7FFFh
5A8000h–5AFFFFh
5B0000h–5B7FFFh
5B8000h–5BFFFFh
5C0000h–5C7FFFh
5C8000h–5CFFFFh
5D0000h–5D7FFFh
5D8000h–5DFFFFh
5E0000h–5E7FFFh
5E8000h–5EFFFFh
5F0000h–5F7FFFh
5F8000h–5FFFFFh
600000h–607FFFh
608000h–60FFFFh
610000h–617FFFh
618000h–61FFFFh
620000h–627FFFh
628000h–62FFFFh
630000h–637FFFh
638000h–63FFFFh
640000h–647FFFh
648000h–64FFFFh
650000h–657FFFh
658000h–65FFFFh
660000h–667FFFh
668000h–66FFFFh
670000h–677FFFh
678000h–67FFFFh
680000h–687FFFh
688000h–68FFFFh
690000h–697FFFh
698000h–69FFFFh
6A0000h–6A7FFFh
6A8000h–6AFFFFh
6B0000h–6B7FFFh
6B8000h–6BFFFFh
6C0000h–6C7FFFh
6C8000h–6CFFFFh
SA225
SA226
SA227
SA228
SA229
SA230
SA231
SA232
SA233
SA234
SA235
SA236
SA237
SA238
SA239
SA240
SA241
SA242
SA243
SA244
SA245
SA246
SA247
SA248
SA249
SA250
SA251
SA252
SA253
SA254
SA255
SA256
SA257
SA258
SA259
SA260
SA261
SA262
SA263
SA264
SA265
SA266
SA267
SA268
SA269
11011010XXX
11011011XXX
11011100XXX
11011101XXX
11011110XXX
11011111XXX
11100000XXX
11100001XXX
11100010XXX
11100011XXX
11100100XXX
11100101XXX
11100110XXX
11100111XXX
11101000XXX
11101001XXX
11101010XXX
11101011XXX
11101100XXX
11101101XXX
11101110XXX
11101111XXX
11110000XXX
11110001XXX
11110010XXX
11110011XXX
11110100XXX
11110101XXX
11110110XXX
11110111XXX
11111000XXX
11111001XXX
11111010XXX
11111011XXX
11111100XXX
11111101XXX
11111110XXX
11111111000
11111111001
11111111010
11111111011
11111111100
11111111101
11111111110
6D0000h–6D7FFFh
6D8000h–6DFFFFh
6E0000h–6E7FFFh
6E8000h–6EFFFFh
6F0000h–6F7FFFh
6F8000h–6FFFFFh
700000h–707FFFh
708000h–70FFFFh
710000h–717FFFh
718000h–71FFFFh
720000h–727FFFh
728000h–72FFFFh
730000h–737FFFh
738000h–73FFFFh
740000h–747FFFh
748000h–74FFFFh
750000h–757FFFh
758000h–75FFFFh
760000h–767FFFh
768000h–76FFFFh
770000h–777FFFh
778000h–77FFFFh
780000h–787FFFh
788000h–78FFFFh
790000h–797FFFh
798000h–79FFFFh
7A0000h–7A7FFFh
7A8000h–7AFFFFh
7B0000h–7B7FFFh
7B8000h–7BFFFFh
7C0000h–7C7FFFh
7C8000h–7CFFFFh
7D0000h–7D7FFFh
7D8000h–7DFFFFh
7E0000h–7E7FFFh
7E8000h–7EFFFFh
7F0000h–7F7FFFh
7F8000h–7F8FFFh
7F9000h–7F9FFFh
7FA000h–7FAFFFh
7FB000h–7FBFFFh
7FC000h–7FCFFFh
7FD000h–7FDFFFh
7FE000h–7FEFFFh
7FF000h–7FFFFFh
4
4
4
4
4
4
11111111111
4
Document Number: 002-00615 Rev. *F
Page 23 of 80
S29PL-J
Table 17. PL064J Sector Architecture (Continued)
Table 17. PL064J Sector Architecture
Sector
Size
Sector Address
(A22-A12)
Bank
Sector
Address Range (x16)
Sector
Sector Address
(A22-A12)
(Kwords)
Bank
Sector
Size
Address Range (x16)
(Kwords)
SA43
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
SA71
SA72
SA73
SA74
SA75
SA76
SA77
SA78
SA79
SA80
SA81
SA82
SA83
SA84
SA85
0100100XXX
0100101XXX
0100110XXX
0100111XXX
0101000XXX
0101001XXX
0101010XXX
0101011XXX
0101100XXX
0101101XXX
0101110XXX
0101111XXX
0110000XXX
0110001XXX
0110010XXX
0110011XXX
0110100XXX
0110101XXX
0110110XXX
0110111XXX
0111000XXX
0111001XXX
0111010XXX
0111011XXX
0111100XXX
0111101XXX
0111110XXX
0111111XXX
1000000XXX
1000001XXX
1000010XXX
1000011XXX
1000100XXX
1000101XXX
1000110XXX
1000111XXX
1001000XXX
1001001XXX
1001010XXX
1001011XXX
1001100XXX
1001101XXX
1001110XXX
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
120000h–127FFFh
128000h–12FFFFh
130000h–137FFFh
138000h–13FFFFh
140000h–147FFFh
148000h–14FFFFh
150000h–157FFFh
158000h–15FFFFh
160000h–167FFFh
168000h–16FFFFh
170000h–177FFFh
178000h–17FFFFh
180000h–187FFFh
188000h–18FFFFh
190000h–197FFFh
198000h–19FFFFh
1A0000h–1A7FFFh
1A8000h–1AFFFFh
1B0000h–1B7FFFh
1B8000h–1BFFFFh
1C0000h–1C7FFFh
1C8000h–1CFFFFh
1D0000h–1D7FFFh
1D8000h–1DFFFFh
1E0000h–1E7FFFh
1E8000h–1EFFFFh
1F0000h–1F7FFFh
1F8000h–1FFFFFh
200000h–207FFFh
208000h–20FFFFh
210000h–217FFFh
218000h–21FFFFh
220000h–227FFFh
228000h–22FFFFh
230000h–237FFFh
238000h–23FFFFh
240000h–247FFFh
248000h–24FFFFh
250000h–257FFFh
258000h–25FFFFh
260000h–267FFFh
268000h–26FFFFh
270000h–277FFFh
SA0
SA1
0000000000
0000000001
0000000010
0000000011
0000000100
0000000101
0000000110
0000000111
0000001XXX
0000010XXX
0000011XXX
0000100XXX
0000101XXX
0000110XXX
0000111XXX
0001000XXX
0001001XXX
0001010XXX
0001011XXX
0001100XXX
0001101XXX
0001110XXX
0001111XXX
0010000XXX
0010001XXX
0010010XXX
0010011XXX
0010100XXX
0010101XXX
0010110XXX
0010111XXX
0011000XXX
0011001XXX
0011010XXX
0011011XXX
0011100XXX
0011101XXX
0011110XXX
0011111XXX
0100000XXX
0100001XXX
0100010XXX
0100011XXX
4
000000h–000FFFh
001000h–001FFFh
002000h–002FFFh
003000h–003FFFh
004000h–004FFFh
005000h–005FFFh
006000h–006FFFh
007000h–007FFFh
008000h–00FFFFh
010000h–017FFFh
018000h–01FFFFh
020000h–027FFFh
028000h–02FFFFh
030000h–037FFFh
038000h–03FFFFh
040000h–047FFFh
048000h–04FFFFh
050000h–057FFFh
058000h–05FFFFh
060000h–067FFFh
068000h–06FFFFh
070000h–077FFFh
078000h–07FFFFh
080000h–087FFFh
088000h–08FFFFh
090000h–097FFFh
098000h–09FFFFh
0A0000h–0A7FFFh
0A8000h–0AFFFFh
0B0000h–0B7FFFh
0B8000h–0BFFFFh
0C0000h–0C7FFFh
0C8000h–0CFFFFh
0D0000h–0D7FFFh
0D8000h–0DFFFFh
0E0000h–0E7FFFh
0E8000h–0EFFFFh
0F0000h–0F7FFFh
0F8000h–0FFFFFh
100000h–107FFFh
108000h–10FFFFh
110000h–117FFFh
118000h–11FFFFh
4
SA2
4
SA3
4
SA4
4
SA5
4
SA6
4
SA7
4
SA8
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
SA9
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
Document Number: 002-00615 Rev. *F
Page 24 of 80
S29PL-J
Table 17. PL064J Sector Architecture (Continued)
Table 17. PL064J Sector Architecture (Continued)
Sector
Sector
Size
(Kwords)
Sector Address
(A22-A12)
Sector Address
(A22-A12)
Bank
Sector
Size
Address Range (x16)
Bank
Sector
Address Range (x16)
(Kwords)
SA86
SA87
1001111XXX
1010000XXX
1010001XXX
1010010XXX
1010011XXX
1010100XXX
1010101XXX
1010110XXX
1010111XXX
1011000XXX
1011001XXX
1011010XXX
1011011XXX
1011100XXX
1011101XXX
1011110XXX
1011111XXX
1100000XXX
1100001XXX
1100010XXX
1100011XXX
1100100XXX
1100101XXX
1100110XXX
1100111XXX
1101000XXX
1101001XXX
1101010XXX
1101011XXX
1101100XXX
1101101XXX
1101110XXX
1101111XXX
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
278000h–27FFFFh
280000h–287FFFh
288000h–28FFFFh
290000h–297FFFh
298000h–29FFFFh
2A0000h–2A7FFFh
2A8000h–2AFFFFh
2B0000h–2B7FFFh
2B8000h–2BFFFFh
2C0000h–2C7FFFh
2C8000h–2CFFFFh
2D0000h–2D7FFFh
2D8000h–2DFFFFh
2E0000h–2E7FFFh
2E8000h–2EFFFFh
2F0000h–2F7FFFh
2F8000h–2FFFFFh
300000h–307FFFh
308000h–30FFFFh
310000h–317FFFh
318000h–31FFFFh
320000h–327FFFh
328000h–32FFFFh
330000h–337FFFh
338000h–33FFFFh
340000h–347FFFh
348000h–34FFFFh
350000h–357FFFh
358000h–35FFFFh
360000h–367FFFh
368000h–36FFFFh
370000h–377FFFh
378000h–37FFFFh
SA119
SA120
SA121
SA122
SA123
SA124
SA125
SA126
SA127
SA128
SA129
SA130
SA131
SA132
SA133
SA134
SA135
SA136
SA137
SA138
SA139
SA140
SA141
1110000XXX
1110001XXX
1110010XXX
1110011XXX
1110100XXX
1110101XXX
1110110XXX
1110111XXX
1111000XXX
1111001XXX
1111010XXX
1111011XXX
1111100XXX
1111101XXX
1111110XXX
1111111000
1111111001
1111111010
1111111011
1111111100
1111111101
1111111110
1111111111
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
4
380000h–387FFFh
388000h–38FFFFh
390000h–397FFFh
398000h–39FFFFh
3A0000h–3A7FFFh
3A8000h–3AFFFFh
3B0000h–3B7FFFh
3B8000h–3BFFFFh
3C0000h–3C7FFFh
3C8000h–3CFFFFh
3D0000h–3D7FFFh
3D8000h–3DFFFFh
3E0000h–3E7FFFh
3E8000h–3EFFFFh
3F0000h–3F7FFFh
3F8000h–3F8FFFh
3F9000h–3F9FFFh
3FA000h–3FAFFFh
3FB000h–3FBFFFh
3FC000h–3FCFFFh
3FD000h–3FDFFFh
3FE000h–3FEFFFh
3FF000h–3FFFFFh
SA88
SA89
SA90
SA91
SA92
SA93
SA94
SA95
SA96
SA97
SA98
SA99
SA100
SA101
SA102
SA103
SA104
SA105
SA106
SA107
SA108
SA109
SA110
SA111
SA112
SA113
SA114
SA115
SA116
SA117
SA118
4
4
4
4
4
4
4
Document Number: 002-00615 Rev. *F
Page 25 of 80
S29PL-J
Table 18. PL032J Sector Architecture (Continued)
Table 18. PL032J Sector Architecture
Sector
Size
SectorAddress
(A22-A12)
Bank
Sector
Address Range (x16)
Sector
SectorAddress
(Kwords)
Bank
Sector
Size
(Kwords)
Address Range (x16)
(A22-A12)
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
100101XXX
100110XXX
100111XXX
101000XXX
101001XXX
101010XXX
101011XXX
101100XXX
101101XXX
101110XXX
101111XXX
110000XXX
110001XXX
110010XXX
110011XXX
110100XXX
110101XXX
110110XXX
110111XXX
111000XXX
111001XXX
111010XXX
111011XXX
111100XXX
111101XXX
111110XXX
111111000
111111001
111111010
111111011
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
4
128000h–12FFFFh
130000h–137FFFh
138000h–13FFFFh
140000h–147FFFh
148000h–14FFFFh
150000h–157FFFh
158000h–15FFFFh
160000h–167FFFh
168000h–16FFFFh
170000h–177FFFh
178000h–17FFFFh
180000h–187FFFh
188000h–18FFFFh
190000h–197FFFh
198000h–19FFFFh
1A0000h–1A7FFFh
1A8000h–1AFFFFh
1B0000h–1B7FFFh
1B8000h–1BFFFFh
1C0000h–1C7FFFh
1C8000h–1CFFFFh
1D0000h–1D7FFFh
1D8000h–1DFFFFh
1E0000h–1E7FFFh
1E8000h–1EFFFFh
1F0000h–1F7FFFh
1F8000h–1F8FFFh
1F9000h–1F9FFFh
1FA000h–1FAFFFh
1FB000h–1FBFFFh
1FC000h–1FCFFFh
1FD000h–1FDFFFh
1FE000h–1FEFFFh
1FF000h–1FFFFFh
SA0
SA1
000000000
000000001
000000010
000000011
000000100
000000101
000000110
000000111
000001XXX
000010XXX
000011XXX
000100XXX
000101XXX
000110XXX
000111XXX
001000XXX
001001XXX
001010XXX
001011XXX
001100XXX
001101XXX
001110XXX
001111XXX
010000XXX
010001XXX
010010XXX
010011XXX
010100XXX
010101XXX
010110XXX
010111XXX
011000XXX
011001XXX
011010XXX
011011XXX
011100XXX
011101XXX
011110XXX
011111XXX
100000XXX
100001XXX
100010XXX
100011XXX
100100XXX
4
000000h–000FFFh
001000h–001FFFh
002000h–002FFFh
003000h–003FFFh
004000h–004FFFh
005000h–005FFFh
006000h–006FFFh
007000h–007FFFh
008000h–00FFFFh
010000h–017FFFh
018000h–01FFFFh
020000h–027FFFh
028000h–02FFFFh
030000h–037FFFh
038000h–03FFFFh
040000h–047FFFh
048000h–04FFFFh
050000h–057FFFh
058000h–05FFFFh
060000h–067FFFh
068000h–06FFFFh
070000h–077FFFh
078000h–07FFFFh
080000h–087FFFh
088000h–08FFFFh
090000h–097FFFh
098000h–09FFFFh
0A0000h–0A7FFFh
0A8000h–0AFFFFh
0B0000h–0B7FFFh
0B8000h–0BFFFFh
0C0000h–0C7FFFh
0C8000h–0CFFFFh
0D0000h–0D7FFFh
0D8000h–0DFFFFh
0E0000h–0E7FFFh
0E8000h–0EFFFFh
0F0000h–0F7FFFh
0F8000h–0FFFFFh
100000h–107FFFh
108000h–10FFFFh
110000h–117FFFh
118000h–11FFFFh
120000h–127FFFh
4
SA2
4
SA3
4
SA4
4
SA5
4
SA6
4
SA7
4
SA8
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
Bank C SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
SA71
SA72
SA73
SA74
SA75
SA76
SA77
SA9
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
SA43
4
4
4
111111100
4
111111101
4
111111110
4
111111111
4
Document Number: 002-00615 Rev. *F
Page 26 of 80
S29PL-J
Table 19. Secured Silicon Sector Addresses
Sector Size
64 words
Address Range
000000h-00003Fh
000040h-00007Fh
Factory-Locked Area
Customer-Lockable Area
64 words
10.8 Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes
output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed
with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command
register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins must be as shown in
Table 20 on page 27. In addition, when verifying sector protection, the sector address must appear on the appropriate highest order
address bits (see Table 15 on page 19). Table 20 shows the remaining address bits that are don’t care. When all necessary bits have
been set as required, the programming equipment may then read the corresponding identifier code on DQ7–DQ0. However, the
autoselect codes can also be accessed in-system through the command register, for instances when the device is erased or
programmed in a system without access to high voltage on the A9 pin. The command sequence is illustrated in Table 28 on page 49.
Note that if a Bank Address (BA) (on address bits PL127J: A22–A20, PL064J: A21–A19, PL032J: A20–A18) is asserted during the
third write cycle of the autoselect command, the host system can read autoselect data that bank and then immediately read array data
from the other bank, without exiting the autoselect mode.
To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown
in Table 28. This method does not require VID. Refer to the Section 15.3 Autoselect Command Sequence on page 43 for more
information.
Table 20. Autoselect Codes (High Voltage Method)
Description
CE# OE# WE# Amax to A12 A10 A9 A8 A7 A6 A5 to A4 A3 A2 A1 A0
DQ15 to DQ0
0001h
Manufacturer ID:
Cypress products
L
L
L
L
H
H
BA
BA
X
X
VID
X
X
L
L
L
L
X
L
L
L
L
L
L
L
L
Read Cycle 1
H
227Eh
2220h (PL127J)
2202h (PL064J)
220Ah (PL032J)
Read Cycle 2
L
H
H
H
L
VID
2200h (PL127J)
2201h (PL064J)
2201h (PL032J)
Read Cycle 3
L
L
H
L
H
L
H
H
H
L
Sector Protection
Verification
0001h (protected),
0000h (unprotected)
L
L
H
H
SA
X
X
VID
X
X
L
L
L
L
DQ7=1
(factory locked),
DQ6=1
(factory and
customer locked)
Secured Silicon
Indicator Bit
(DQ7, DQ6)
L
BA[14]
VID
X
X
L
L
H
H
Note
14. When Polling the Secured Silicon indicator bit the Bank Address (BA) should be set within the address range 004000h-03FFFFh.
Legend
L = Logic Low = V , H = Logic High = V , BA = Bank Address, SA = Sector Address, X = Don’t care.
IL
IH
Document Number: 002-00615 Rev. *F
Page 27 of 80
S29PL-J
Table 21. PL127J Boot Sector/Sector Block Addresses for Protection/Unprotection
Sector
SA0
A22-A12
Sector/Sector Block Size
4 Kwords
Sector
A22-A12
Sector/Sector Block Size
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
32 Kwords
00000000000
00000000001
00000000010
00000000011
00000000100
00000000101
00000000110
00000000111
00000001XXX
00000010XXX
00000011XXX
000001XXXXX
000010XXXXX
000011XXXXX
000100XXXXX
000101XXXXX
000110XXXXX
000111XXXXX
001000XXXXX
001001XXXXX
001010XXXXX
001011XXXXX
001100XXXXX
001101XXXXX
001110XXXXX
001111XXXXX
010000XXXXX
010001XXXXX
010010XXXXX
010011XXXXX
010100XXXXX
010101XXXXX
010110XXXXX
010111XXXXX
011000XXXXX
011001XXXXX
011010XXXXX
011011XXXXX
011100XXXXX
011101XXXXX
011110XXXXX
SA131-SA134
SA135-SA138
SA139-SA142
SA143-SA146
SA147-SA150
SA151-SA154
SA155-SA158
SA159-SA162
SA163-SA166
SA167-SA170
SA171-SA174
SA175-SA178
SA179-SA182
SA183-SA186
SA187-SA190
SA191-SA194
SA195-SA198
SA199-SA202
SA203-SA206
SA207-SA210
SA211-SA214
SA215-SA218
SA219-SA222
SA223-SA226
SA227-SA230
SA231-SA234
SA235-SA238
SA239-SA242
SA243-SA246
SA247-SA250
SA251-SA254
SA255-SA258
SA259
011111XXXXX
100000XXXXX
100001XXXXX
100010XXXXX
100011XXXXX
100100XXXXX
100101XXXXX
100110XXXXX
100111XXXXX
101000XXXXX
101001XXXXX
101010XXXXX
101011XXXXX
101100XXXXX
101101XXXXX
101110XXXXX
101111XXXXX
110000XXXXX
110001XXXXX
110010XXXXX
110011XXXXX
110100XXXXX
110101XXXXX
110110XXXXX
110111XXXXX
111000XXXXX
111001XXXXX
111010XXXXX
111011XXXXX
111100XXXXX
111101XXXXX
111110XXXXX
11111100XXX
11111101XXX
11111110XXX
11111111000
SA1
4 Kwords
SA2
4 Kwords
SA3
4 Kwords
SA4
4 Kwords
SA5
4 Kwords
SA6
4 Kwords
SA7
4 Kwords
SA8
32 Kwords
SA9
32 Kwords
SA10
32 Kwords
SA11-SA14
SA15-SA18
SA19-SA22
SA23-SA26
SA27-SA30
SA31-SA34
SA35-SA38
SA39-SA42
SA43-SA46
SA47-SA50
SA51-SA54
SA55-SA58
SA59-SA62
SA63-SA66
SA67-SA70
SA71-SA74
SA75-SA78
SA79-SA82
SA83-SA86
SA87-SA90
SA91-SA94
SA95-SA98
SA99-SA102
SA103-SA106
SA107-SA110
SA111-SA114
SA115-SA118
SA119-SA122
SA123-SA126
SA127-SA130
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
SA260
32 Kwords
SA261
32 Kwords
SA262
4 Kwords
SA263
11111111001
4 Kwords
SA264
11111111010
4 Kwords
SA265
11111111011
4 Kwords
The device is shipped with all sectors unprotected. Optional Cypress programming services enable programming and protecting
sectors at the factory prior to shipping the device. Contact your local sales office for details.
It is possible to determine whether a sector is protected or unprotected. See Table 19 on page 27 for details.
Document Number: 002-00615 Rev. *F
Page 28 of 80
S29PL-J
10.9 Selecting a Sector Protection Mode
Table 22. PL064J Boot Sector/Sector Block Addresses for Protection/Unprotection
Sector/Sector Block
Sector/Sector Block
Size
Sector
A21-A12
Sector
A21-A12
Size
SA0
SA1
0000000000
0000000001
0000000010
0000000011
0000000100
0000000101
0000000110
0000000111
0000001XXX
0000010XXX
0000011XXX
00001XXXXX
00010XXXXX
00011XXXXX
00100XXXXX
00101XXXXX
00110XXXXX
00111XXXXX
01000XXXXX
01001XXXXX
01010XXXXX
01011XXXXX
01100XXXXX
01101XXXXX
01110XXXXX
01111XXXXX
10000XXXXX
10001XXXXX
10010XXXXX
10011XXXXX
10100XXXXX
10101XXXXX
10110XXXXX
10111XXXXX
11000XXXXX
11001XXXXX
11010XXXXX
4 Kwords
SA115-SA118
SA119-SA122
SA123-SA126
SA127-SA130
SA131
11011XXXXX
11100XXXXX
11101XXXXX
11110XXXXX
1111100XXX
1111101XXX
1111110XXX
1111111000
1111111001
1111111010
1111111011
1111111100
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
32 Kwords
4 Kwords
SA2
4 Kwords
SA3
4 Kwords
SA4
4 Kwords
SA5
4 Kwords
SA132
32 Kwords
SA6
4 Kwords
SA133
32 Kwords
SA7
4 Kwords
SA134
4 Kwords
SA8
32 Kwords
SA135
4 Kwords
SA9
32 Kwords
SA136
4 Kwords
SA10
32 Kwords
SA137
4 Kwords
SA11-SA14
SA15-SA18
SA19-SA22
SA23-SA26
SA27-SA30
SA31-SA34
SA35-SA38
SA39-SA42
SA43-SA46
SA47-SA50
SA51-SA54
SA55-SA58
SA59-SA62
SA63-SA66
SA67-SA70
SA71-SA74
SA75-SA78
SA79-SA82
SA83-SA86
SA87-SA90
SA91-SA94
SA95-SA98
SA99-SA102
SA103-SA106
SA107-SA110
SA111-SA114
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
128 (4x32) Kwords
SA138
4 Kwords
Document Number: 002-00615 Rev. *F
Page 29 of 80
S29PL-J
Table 23. Sector Protection Schemes
DYB
PPB
0
PPB Lock
Sector State
0
0
0
1
1
0
1
1
0
1
0
0
0
1
1
1
Unprotected—PPB and DYB are changeable
0
Unprotected—PPB not changeable, DYB is changeable
1
0
Protected—PPB and DYB are changeable
1
1
0
Protected—PPB not changeable, DYB is changeable
1
Document Number: 002-00615 Rev. *F
Page 30 of 80
S29PL-J
11. Sector Protection
The PL127J, PL064J, and PL032J features several levels of sector protection, which can disable both the program and erase
operations in certain sectors or sector groups:
11.1 Persistent Sector Protection
A command sector protection method that replaces the old 12 V controlled protection method.
11.2 Password Sector Protection
A highly sophisticated protection method that requires a password before changes to certain sectors or sector groups are permitted
11.3 WP# Hardware Protection
A write protect pin that can prevent program or erase operations in sectors SA1-133, SA1-134, SA2-0 and SA2-1.
The WP# Hardware Protection feature is always available, independent of the software managed protection method chosen.
11.4 Selecting a Sector Protection Mode
All parts default to operate in the Persistent Sector Protection mode. The customer must then choose if the Persistent or Password
Protection method is most desirable. There are two one-time programmable non-volatile bits that define which sector protection
method will be used. If the Persistent Sector Protection method is desired, programming the Persistent Sector Protection Mode
Locking Bit permanently sets the device to the Persistent Sector Protection mode. If the Password Sector Protection method is desired,
programming the Password Mode Locking Bit permanently sets the device to the Password Sector Protection mode. It is not possible
to switch between the two protection modes once a locking bit has been set. One of the two modes must be selected when the device
is first programmed. This prevents a program or virus from later setting the Password Mode Locking Bit, which would cause an
unexpected shift from the default Persistent Sector Protection Mode into the Password Protection Mode.
The device is shipped with all sectors unprotected. Optional Cypress programming services enable programming and protecting
sectors at the factory prior to shipping the device. Contact your local sales office for details.
It is possible to determine whether a sector is protected or unprotected. See Autoselect Mode on page 27 for details.
Document Number: 002-00615 Rev. *F
Page 31 of 80
S29PL-J
12. Persistent Sector Protection
The Persistent Sector Protection method replaces the 12 V controlled protection method in previous flash devices. This new method
provides three different sector protection states:
■ Persistently Locked—The sector is protected and cannot be changed.
■ Dynamically Locked—The sector is protected and can be changed by a simple command.
■ Unlocked—The sector is unprotected and can be changed by a simple command.
To achieve these states, three types of “bits” are used:
■ Persistent Protection Bit
■ Persistent Protection Bit Lock
■ Persistent Sector Protection Mode Locking Bit
12.1 Persistent Protection Bit (PPB)
A single Persistent (non-volatile) Protection Bit is assigned to a maximum four sectors (see the sector address tables for specific
sector protection groupings). All 4 Kword boot-block sectors have individual sector Persistent Protection Bits (PPBs) for greater
flexibility. Each PPB is individually modifiable through the PPB Write Command.
The device erases all PPBs in parallel. If any PPB requires erasure, the device must be instructed to preprogram all of the sector
PPBs prior to PPB erasure. Otherwise, a previously erased sector PPBs can potentially be over-erased. The flash device does not
have a built-in means of preventing sector PPBs over-erasure.
12.2 Persistent Protection Bit Lock (PPB Lock)
The Persistent Protection Bit Lock (PPB Lock) is a global volatile bit. When set to “1”, the PPBs cannot be changed. When cleared
(“0”), the PPBs are changeable. There is only one PPB Lock bit per device. The PPB Lock is cleared after power-up or hardware
reset. There is no command sequence to unlock the PPB Lock.
12.3 Dynamic Protection Bit (DYB)
A volatile protection bit is assigned for each sector. After power-up or hardware reset, the contents of all DYBs is “0”. Each DYB is
individually modifiable through the DYB Write Command.
When the parts are first shipped, the PPBs are cleared, the DYBs are cleared, and PPB Lock is defaulted to power up in the cleared
state – meaning the PPBs are changeable.
When the device is first powered on the DYBs power up cleared (sectors not protected). The Protection State for each sector is
determined by the logical OR of the PPB and the DYB related to that sector. For the sectors that have the PPBs cleared, the DYBs
control whether or not the sector is protected or unprotected. By issuing the DYB Write command sequences, the DYBs will be set or
cleared, thus placing each sector in the protected or unprotected state. These are the so-called Dynamic Locked or Unlocked states.
They are called dynamic states because it is very easy to switch back and forth between the protected and unprotected conditions.
This allows software to easily protect sectors against inadvertent changes yet does not prevent the easy removal of protection when
changes are needed. The DYBs maybe set or cleared as often as needed.
The PPBs allow for a more static, and difficult to change, level of protection. The PPBs retain their state across power cycles because
they are non-volatile. Individual PPBs are set with a command but must all be cleared as a group through a complex sequence of
program and erasing commands. The PPBs are also limited to 100 erase cycles.
The PPB Lock bit adds an additional level of protection. Once all PPBs are programmed to the desired settings, the PPB Lock may
be set to “1”. Setting the PPB Lock disables all program and erase commands to the non-volatile PPBs. In effect, the PPB Lock Bit
locks the PPBs into their current state. The only way to clear the PPB Lock is to go through a power cycle. System boot code can
determine if any changes to the PPB are needed; for example, to allow new system code to be downloaded. If no changes are needed
then the boot code can set the PPB Lock to disable any further changes to the PPBs during system operation.
The WP#/ACC write protect pin adds a final level of hardware protection to sectors SA1-133, SA1-134, SA2-0 and SA2-1. When this
pin is low it is not possible to change the contents of these sectors. These sectors generally hold system boot code. The WP#/ACC
pin can prevent any changes to the boot code that could override the choices made while setting up sector protection during system
initialization.
Document Number: 002-00615 Rev. *F
Page 32 of 80
S29PL-J
For customers who are concerned about malicious viruses there is another level of security - the persistently locked state. To
persistently protect a given sector or sector group, the PPBs associated with that sector need to be set to “1”. Once all PPBs are
programmed to the desired settings, the PPB Lock should be set to “1”. Setting the PPB Lock automatically disables all program and
erase commands to the Non-Volatile PPBs. In effect, the PPB Lock “freezes” the PPBs into their current state. The only way to clear
the PPB Lock is to go through a power cycle.
It is possible to have sectors that have been persistently locked, and sectors that are left in the dynamic state. The sectors in the
dynamic state are all unprotected. If there is a need to protect some of them, a simple DYB Write command sequence is all that is
necessary. The DYB write command for the dynamic sectors switch the DYBs to signify protected and unprotected, respectively. If
there is a need to change the status of the persistently locked sectors, a few more steps are required. First, the PPB Lock bit must
be disabled by either putting the device through a power-cycle, or hardware reset. The PPBs can then be changed to reflect the
desired settings. Setting the PPB lock bit once again will lock the PPBs, and the device operates normally again.
The best protection is achieved by executing the PPB lock bit set command early in the boot code, and protect the boot code by
holding WP#/ACC = VIL.
Table 23 on page 30 contains all possible combinations of the DYB, PPB, and PPB lock relating to the status of the sector.
In summary, if the PPB is set, and the PPB lock is set, the sector is protected and the protection can not be removed until the next
power cycle clears the PPB lock. If the PPB is cleared, the sector can be dynamically locked or unlocked. The DYB then controls
whether or not the sector is protected or unprotected.
If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. A program
command to a protected sector enables status polling for approximately 1 µs before the device returns to read mode without having
modified the contents of the protected sector. An erase command to a protected sector enables status polling for approximately
50 µs after which the device returns to read mode without having erased the protected sector.
The programming of the DYB, PPB, and PPB lock for a given sector can be verified by writing a DYB/PPB/PPB lock verify command
to the device. There is an alternative means of reading the protection status. Take RESET# to VIL and hold WE# at VIH. (The high
voltage A9 Autoselect Mode also works for reading the status of the PPBs). Scanning the addresses (A18–A11) while (A6, A1, A0) =
(0, 1, 0) will produce a logical ‘1” code at device output DQ0 for a protected sector or a “0” for an unprotected sector. In this mode,
the other addresses are don’t cares. Address location with A1 = VIL are reserved for autoselect manufacturer and device codes.
12.4 Persistent Sector Protection Mode Locking Bit
Like the password mode locking bit, a Persistent Sector Protection mode locking bit exists to guarantee that the device remain in
software sector protection. Once set, the Persistent Sector Protection locking bit prevents programming of the password protection
mode locking bit. This guarantees that a hacker could not place the device in password protection mode.
Document Number: 002-00615 Rev. *F
Page 33 of 80
S29PL-J
13. Password Protection Mode
The Password Sector Protection Mode method allows an even higher level of security than the Persistent Sector Protection Mode.
There are two main differences between the Persistent Sector Protection and the Password Sector Protection Mode:
When the device is first powered on, or comes out of a reset cycle, the PPB Lock bit set to the locked state, rather than cleared to the
unlocked state.
The only means to clear the PPB Lock bit is by writing a unique 64-bit Password to the device.
The Password Sector Protection method is otherwise identical to the Persistent Sector Protection method.
A 64-bit password is the only additional tool utilized in this method.
Once the Password Mode Locking Bit is set, the password is permanently set with no means to read, program, or erase it. The
password is used to clear the PPB Lock bit. The Password Unlock command must be written to the flash, along with a password. The
flash device internally compares the given password with the pre-programmed password. If they match, the PPB Lock bit is cleared,
and the PPBs can be altered. If they do not match, the flash device does nothing. There is a built-in 2 µs delay for each “password
check.” This delay is intended to thwart any efforts to run a program that tries all possible combinations in order to crack the password.
13.1 Password and Password Mode Locking Bit
In order to select the Password sector protection scheme, the customer must first program the password. The password may be
correlated to the unique Electronic Serial Number (ESN) of the particular flash device. Each ESN is different for every flash device;
therefore each password should be different for every flash device. While programming in the password region, the customer may
perform Password Verify operations.
Once the desired password is programmed in, the customer must then set the Password Mode Locking Bit. This operation achieves
two objectives:
Permanently sets the device to operate using the Password Protection Mode. It is not possible to reverse this function.
Disables all further commands to the password region. All program, and read operations are ignored.
Both of these objectives are important, and if not carefully considered, may lead to unrecoverable errors. The user must be sure that
the Password Protection method is desired when setting the Password Mode Locking Bit. More importantly, the user must be sure
that the password is correct when the Password Mode Locking Bit is set. Due to the fact that read operations are disabled, there is
no means to verify what the password is afterwards. If the password is lost after setting the Password Mode Locking Bit, there will be
no way to clear the PPB Lock bit.
The Password Mode Locking Bit, once set, prevents reading the 64-bit password on the DQ bus and further password programming.
The Password Mode Locking Bit is not erasable. Once Password Mode Locking Bit is programmed, the Persistent Sector Protection
Locking Bit is disabled from programming, guaranteeing that no changes to the protection scheme are allowed.
13.2 64-bit Password
The 64-bit Password is located in its own memory space and is accessible through the use of the Password Program and Verify
commands (see “Password Verify Command”). The password function works in conjunction with the Password Mode Locking Bit,
which when set, prevents the Password Verify command from reading the contents of the password on the pins of the device.
Document Number: 002-00615 Rev. *F
Page 34 of 80
S29PL-J
13.3 Write Protect (WP#)
The Write Protect feature provides a hardware method of protecting the upper two and lower two sectors without using VID. This
function is provided by the WP# pin and overrides the previously discussed Section 13.4 High Voltage Sector Protection on page 35
method.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two outermost 4 Kword sectors
on both ends of the flash array independent of whether it was previously protected or unprotected.
If the system asserts VIH on the WP#/ACC pin, the device reverts the upper two and lower two sectors to whether they were last set
to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last protected
or unprotected using the method described in the Section 13.4 High Voltage Sector Protection on page 35.
Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result.
13.3.1 Persistent Protection Bit Lock
The Persistent Protection Bit (PPB) Lock is a volatile bit that reflects the state of the Password Mode Locking Bit after power-up reset.
If the Password Mode Lock Bit is also set after a hardware reset (RESET# asserted) or a power-up reset, the ONLY means for clearing
the PPB Lock Bit in Password Protection Mode is to issue the Password Unlock command. Successful execution of the Password
Unlock command clears the PPB Lock Bit, allowing for sector PPBs modifications. Asserting RESET#, taking the device through a
power-on reset, or issuing the PPB Lock Bit Set command sets the PPB Lock Bit to a “1” when the Password Mode Lock Bit is not set.
If the Password Mode Locking Bit is not set, including Persistent Protection Mode, the PPB Lock Bit is cleared after power-up or
hardware reset. The PPB Lock Bit is set by issuing the PPB Lock Bit Set command. Once set the only means for clearing the PPB
Lock Bit is by issuing a hardware or power-up reset. The Password Unlock command is ignored in Persistent Protection Mode.
13.4 High Voltage Sector Protection
Sector protection and unprotection may also be implemented using programming equipment. The procedure requires high voltage
(VID) to be placed on the RESET# pin. Refer to Figure 6 on page 36 for details on this procedure. Note that for sector unprotect, all
unprotected sectors must first be protected prior to the first sector write cycle.
Document Number: 002-00615 Rev. *F
Page 35 of 80
S29PL-J
Figure 6. In-System Sector Protection/Sector Unprotection Algorithms
START
START
Protect all sectors:
PLSCNT = 1
PLSCNT = 1
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
RESET# = VID
RESET# = VID
Wait 1 μs
Wait 1 μs
unprotect address
No
No
First Write
First Write
Cycle = 60h?
Temporary Sector
Unprotect Mode
Temporary Sector
Unprotect Mode
Cycle = 60h?
Yes
Yes
Set up sector
address
No
All sectors
protected?
Sector Protect:
Write 60h to sector
address with
Yes
Set up first sector
address
A7-A0 = 00000010
Sector Unprotect:
Wait 150 µs
Write 60h to sector
address with
A7-A0 =
Verify Sector
Protect: Write 40h
to sector address
with A7-A0 =
01000010
Reset
PLSCNT = 1
Increment
PLSCNT
Wait 15 ms
00000010
Verify Sector
Unprotect: Write
40h to sector
address with
A7-A0 =
Read from
sector address
with A7-A0 =
00000010
Increment
PLSCNT
No
00000010
No
PLSCNT
= 25?
Read from
sector address
with A7-A0 =
00000010
Data = 01h?
Yes
No
Yes
Set up
next sector
address
Yes
No
PLSCNT
= 1000?
Protect another
sector?
Remove V
ID
Data = 00h?
Yes
from RESET#
No
Yes
Write reset
command
Remove VID
from RESET#
No
Last sector
verified?
Remove V
from RESET#
ID
Sector Protect
complete
Write reset
command
Yes
Write reset
command
Remove VID
from RESET#
Device failed
Sector Protect
complete
Sector Protect
complete
Write reset
command
Sector Protect
Algorithm
Device failed
Sector Unprotect
complete
Sector Unprotect
Algorithm
Document Number: 002-00615 Rev. *F
Page 36 of 80
S29PL-J
13.5 Temporary Sector Unprotect
This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is
activated by setting the RESET# pin to VID. During this mode, formerly protected sectors can be programmed or erased by selecting
the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 7
on page 37 shows the algorithm, and Figure 26 on page 68 shows the timing diagrams, for this feature. While PPB lock is set, the
device cannot enter the Temporary Sector Unprotection Mode.
Figure 7. Temporary Sector Unprotect Operation[15, 16]
START
RESET# = VID
Note 15
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Unprotect Completed
Note 16
13.6 Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector feature provides a Flash memory region that enables permanent part identification through an Electronic
Serial Number (ESN) The 128-word Secured Silicon sector is divided into 64 factory-lockable words that can be programmed and
locked by the customer. The Secured Silicon sector is located at addresses 000000h-00007Fh in both Persistent Protection mode
and Password Protection mode. Indicator bits DQ6 and DQ7 are used to indicate the factory-locked and customer locked status of
the part.
The system accesses the Secured Silicon Sector through a command sequence (see Section 15.4 Enter/Exit Secured Silicon Sector
Command Sequence on page 44). After the system has written the Enter Secured Silicon Sector command sequence, it may read
the Secured Silicon Sector by using the addresses normally occupied by the boot sectors. This mode of operation continues until the
system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. Once the Enter SecSi
Sector Command sequence has been entered, the standard array cannot be accessed until the Exit SecSi Sector command has been
entered or the device has been reset. On power-up, or following a hardware reset, the device reverts to sending commands to the
normal address space. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is
enabled.
13.6.1 Factory-Locked Area (64 words)
The factory-locked area of the Secured Silicon Sector (000000h-00003Fh) is locked when the part is shipped, whether or not the area
was programmed at the factory. The Secured Silicon Sector Factory-locked Indicator Bit (DQ7) is permanently set to a “1”. Optional
Cypress programming services can program the factory-locked area with a random ESN, a customer-defined code, or any combi-
nation of the two. Because only Cypress can program and protect the factory-locked area, this method ensures the security of the
ESN once the product is shipped to the field. Contact your local sales office for details on using Cypress’s programming services.
Note that the ACC function and unlock bypass modes are not available when the Secured Silicon sector is enabled.
Notes
15. All protected sectors unprotected (If WP#/ACC = V , upper two and lower two sectors will remain protected).
IL
16. All previously protected sectors are protected once again.
Document Number: 002-00615 Rev. *F
Page 37 of 80
S29PL-J
13.6.2 Customer-Lockable Area (64 words)
The customer-lockable area of the Secured Silicon Sector (000040h-00007Fh) is shipped unprotected, which allows the customer to
program and optionally lock the area as appropriate for the application. The Secured Silicon Sector Customer-locked Indicator Bit
(DQ6) is shipped as “0” and can be permanently locked to “1” by issuing the Secured Silicon Protection Bit Program Command. The
Secured Silicon Sector can be read any number of times, but can be programmed and locked only once. Note that the accelerated
programming (ACC) and unlock bypass functions are not available when programming the Secured Silicon Sector.
The Customer-lockable Secured Silicon Sector area can be protected using one of the following procedures:
■ Writethethree-cycleEnterSecuredSiliconSectorRegioncommandsequence, andthenfollowthein-systemsectorprotectalgorithm
as shown in Figure 6 on page 36, except that RESET# may be at either VIH or VID. This allows in-system protection of the Secured
Silicon Sector Region without raising any device pin to a high voltage. Note that this method is only applicable to the Secured Silicon
Sector.
■ To verify the protect/unprotect status of the Secured Silicon Sector, follow the algorithm shown in Figure 8 on page 38.
■ Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector Region command
sequence to return to reading and writing the remainder of the array.
The Secured Silicon Sector lock must be used with caution since, once locked, there is no procedure available for unlocking the
Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way.
13.6.3 Secured Silicon Sector Protection Bits
The Secured Silicon Sector Protection Bits prevent programming of the Secured Silicon Sector memory area. Once set, the Secured
Silicon Sector memory area contents are non-modifiable.
Figure 8. Secured Silicon Sector Protect Verify
START
If data = 00h,
RESET# =
SecSi Sector is
VIH or VID
unprotected.
If data = 01h,
SecSi Sector is
protected.
Wait 1 µs
Write 60h to
any address
Remove VIH or VID
from RESET#
Write 40h to SecSi
Sector address
Write reset
with A6 = 0,
command
A1 = 1, A0 = 0
SecSi Sector
Read from SecSi
Protect Verify
Sector address
complete
with A6 = 0,
A1 = 1, A0 = 0
Document Number: 002-00615 Rev. *F
Page 38 of 80
S29PL-J
13.7 Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes.
In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise.
13.7.1 Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down.
The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes
are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional
writes when VCC is greater than VLKO
.
13.7.2 Write Pulse “Glitch” Protection
Noise pulses of less than 3 ns (typical) on OE#, CE#, or WE# do not initiate a write cycle.
13.7.3 Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be
a logical zero while OE# is a logical one.
13.7.4 Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal
state machine is automatically reset to the read mode on power-up.
Document Number: 002-00615 Rev. *F
Page 39 of 80
S29PL-J
14. Common Flash Memory Interface (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows
specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be
device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash
vendors can standardize their existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device
is ready to read array data. The system can read CFI information at the addresses given in Table 24 on page 40 to Table 27
on page 42. To terminate reading CFI data, the system must write the reset command. The CFI Query mode is not accessible when
the device is executing an Embedded Program or embedded Erase algorithm.
The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode,
and the system can read CFI data at the addresses given in Table 24 through Table 27. The system must write the reset command
to return the device to reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100. Contact your local sales office for copies of
these documents.
Table 24. CFI Query Identification String
Addresses
Data
Description
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
Primary OEM Command Set
13h
14h
0002h
0000h
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
19h
1Ah
0000h
0000h
Table 25. System Interface String
Addresses
Data
Description
V
CC Min. (write/erase)
1Bh
1Ch
0027h
D7–D4: volt, D3–D0: 100 millivolt
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
0036h
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
0000h
0000h
0003h
0000h
0009h
0000h
0004h
0000h
0004h
0000h
VPP Min. voltage (00h = no VPP pin present)
VPP Max. voltage (00h = no VPP pin present)
Typical timeout per single byte/word write 2N µs
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
Typical timeout per individual block erase 2N ms
Typical timeout for full chip erase 2N ms (00h = not supported)
Max. timeout for byte/word write 2N times typical
Max. timeout for buffer write 2N times typical
Max. timeout per individual block erase 2N times typical
Max. timeout for full chip erase 2N times typical (00h = not supported)
Document Number: 002-00615 Rev. *F
Page 40 of 80
S29PL-J
Table 26. Device Geometry Definition
Addresses
Data
Description
0018h (PL127J)
0017h (PL064J)
0016h (PL032J)
27h
Device Size = 2N byte
28h
29h
0001h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
0000h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
0003h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
0007h
0000h
0020h
0000h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
00FDh (PL127J)
007Dh (PL064J)
003Dh (PL032J)
31h
Erase Block Region 2 Information
(refer to the CFI specification or CFI publication 100)
32h
33h
34h
0000h
0000h
0001h
35h
36h
37h
38h
0007h
0000h
0020h
0000h
Erase Block Region 3 Information
(refer to the CFI specification or CFI publication 100)
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
Erase Block Region 4 Information
(refer to the CFI specification or CFI publication 100)
Document Number: 002-00615 Rev. *F
Page 41 of 80
S29PL-J
Table 27. Primary Vendor-Specific Extended Query
Addresses
Data
Description
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
44h
0031h
0033h
Major version number, ASCII (reflects modifications to the silicon)
Minor version number, ASCII (reflects modifications to the CFI table)
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Silicon Revision Number (Bits 7-2)
45h
TBD
Erase Suspend
46h
47h
48h
49h
0002h
0001h
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
Sector Protect
0 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
0001h
Sector Protect/Unprotect scheme
07 = Advanced Sector Protection
0007h (PLxxxJ)
00E7h (PL127J)
0077h (PL064J)
003Fh (PL032J)
Simultaneous Operation
00 = Not Supported, X = Number of Sectors excluding Bank 1
4Ah
Burst Mode Type
4Bh
4Ch
4Dh
4Eh
0000h
0002h (PLxxxJ)
0085h
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
0095h
Top/Bottom Boot Sector Flag
00h = Uniform device, 01h = Both top and bottom boot with write protect,
02h = Bottom Boot Device, 03h = Top Boot Device,
04h = Both Top and Bottom
4Fh
0001h
Program Suspend
50h
57h
0001h
0004h
0 = Not supported, 1 = Supported
Bank Organization
00 = Data at 4Ah is zero, X = Number of Banks
0027h (PL127J)
0017h (PL064J)
000Fh (PL032J)
Bank 1 Region Information
58h
59h
5Ah
5Bh
X = Number of Sectors in Bank 1
0060h (PL127J)
0030h (PL064J)
0018h (PL032J)
Bank 2 Region Information
X = Number of Sectors in Bank 2
0060h (PL127J)
0030h (PL064J)
0018h (PL032J)
Bank 3 Region Information
X = Number of Sectors in Bank 3
0027h (PL127J)
0017h (PL064J)
000Fh (PL032J)
Bank 4 Region Information
X = Number of Sectors in Bank 4
Document Number: 002-00615 Rev. *F
Page 42 of 80
S29PL-J
15. Command Definitions
Writing specific address and data commands or sequences into the command register initiates device operations. Table 28
on page 49 defines the valid register command sequences. Writing incorrect address and data values or writing them in the
improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading
array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE#
or CE#, whichever happens first. Refer to Section 20. AC Characteristics on page 60 for timing diagrams.
15.1 Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. Each bank
is ready to read array data after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the corresponding bank enters the erase-suspend-read mode, after which the
system can read data from any non-erase-suspended sector within the same bank. The system can read array data using the standard
read timing, except that if it reads at an address within erase-suspended sectors, the device outputs status data. After completing a
programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See
Section 15.8 Erase Suspend/Erase Resume Commands on page 47 for more information.
After the device accepts a Program Suspend command, the corresponding bank enters the program-suspend-read mode, after which
the system can read data from any non-program-suspended sector within the same bank. See Section 15.9 Program
Suspend/Program Resume Commands on page 48 for more information.
The system must issue the reset command to return a bank to the read (or erase-suspend-read) mode if DQ5 goes high during an
active program or erase operation, or if the bank is in the autoselect mode. See Section 15.2 Reset Command on page 43 for more
information.
See also Section 10.1 Requirements for Reading Array Data on page 18 for more information. Section 20. AC Characteristics
on page 60 provides the read parameters, and Figure 12 on page 54 shows the timing diagram.
15.2 Reset Command
Writing the reset command resets the banks to the read or erase-suspend-read mode. Address bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets
the bank to which the system was writing to the read mode. Once erasure begins, however, the device ignores reset commands until
the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence before programming begins.
This resets the bank to which the system was writing to the read mode. If the program command sequence is written to a bank that
is in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. Once programming
begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode,
the reset command must be written to return to the read mode. If a bank entered the autoselect mode while in the Erase Suspend
mode, writing the reset command returns that bank to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to the read mode (or
erase-suspend-read mode if that bank was in Erase Suspend and program-suspend-read mode if that bank was in Program Suspend).
15.3 Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or
not a sector is protected. The autoselect command sequence may be written to an address within a bank that is either in the read or
erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing in the
other bank.
The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains
the bank address and the autoselect command. The bank then enters the autoselect mode. The system may read any number of
autoselect codes without reinitiating the command sequence.
Table 28 on page 49 shows the address and data requirements. To determine sector protection information, the system must write to
the appropriate bank address (BA) and sector address (SA). Table 15 on page 19 shows the address range and bank number
associated with each sector.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the bank was previously in
Erase Suspend).
Document Number: 002-00615 Rev. *F
Page 43 of 80
S29PL-J
15.4 Enter/Exit Secured Silicon Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing a random, eight word electronic serial number (ESN). The
system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command sequence.
The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector
command sequence. The Exit Secured Silicon Sector command sequence returns the device to normal operation. The Secured Silicon
Sector is not accessible when the device is executing an Embedded Program or embedded Erase algorithm. Table 28 on page 49
shows the address and data requirements for both command sequences. See also Section 13.6 Secured Silicon Sector
Flash Memory Region on page 37 for further information. Note that the ACC function and unlock bypass modes are not available when
the Secured Silicon Sector is enabled.
15.5 Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed
by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program
algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated
program pulses and verifies the programmed cell margin. Table 28 on page 49 shows the address and data requirements for the
program command sequence. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a
[program/erase] operation is in progress.
When the Embedded Program algorithm is complete, that bank then returns to the read mode and addresses are no longer latched.
The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to Section 16. Write Operation
Status on page 52 for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately
terminates the program operation. The program command sequence should be reinitiated once that bank has returned to the read
mode, to ensure data integrity. Note that the Secured Silicon Sector, autoselect and CFI functions are unavailable when the Secured
Silicon Sector is enabled.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from “0” back to a “1.”
Attempting to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was
successful. However, a succeeding read will show that the data is still “0.” Only erase operations can convert a “0” to a “1.”
Document Number: 002-00615 Rev. *F
Page 44 of 80
S29PL-J
15.5.1 Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program data to a bank faster than using the standard program command sequence.
The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing
the unlock bypass command, 20h. That bank then enters the unlock bypass mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command,
A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode
dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming
time. Table 28 on page 49 shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock
bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. (See Table 29 on page 50)
The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin,
the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command
sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not
be at VHH any operation other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not
be left floating or unconnected; inconsistent behavior of the device may result.
Figure 9 on page 45 illustrates the algorithm for the program operation. Refer to the table Section 20.5 Erase/Program Operations
on page 64 for parameters, and Figure 19 on page 65 for timing diagrams.
Figure 9. Program Operation[17]
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
No
Increment Address
Last Address?
Yes
Programming
Completed
Note
17. See Table 28 on page 49 for program command sequence.
Document Number: 002-00615 Rev. *F
Page 45 of 80
S29PL-J
15.6 Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a
set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the
Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not
required to provide any controls or timings during these operations. Table 28 on page 49 shows the address and data requirements
for the chip erase command sequence.
When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no longer latched. The
system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or
RY/BY#. Refer to Section 16. Write Operation Status on page 52 for information on these status bits.
Any commands written during the chip erase operation are ignored. Note that Secured Silicon Sector, autoselect, and CFI functions
are unavailable when a [program/erase] operation is in progress. However, note that a hardware reset immediately terminates the
erase operation. If that occurs, the chip erase command sequence should be reinitiated once that bank has returned to reading array
data, to ensure data integrity.
Figure 10 on page 47 illustrates the algorithm for the erase operation. Refer to the tables in Section 20.5 Erase/Program Operations
on page 64 for parameters, and Figure 21 on page 66 for timing diagrams.
15.7 Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by
a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the
sector erase command. Table 28 on page 49 shows the address and data requirements for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and
verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or
timings during these operations.
After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector
addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number
of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise erasure
may begin. Any sector erase address and command following the exceeded time-out may or may not be accepted. It is recommended
that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after
the last Sector Erase command is written. If any command other than 30h, B0h, F0h is input during the time-out period, the
normal operation will not be guaranteed. The system must rewrite the command sequence and any additional addresses and
commands. Note that Secured Silicon Sector, autoselect, and CFI functions are unavailable when a [program/erase] operation is in
progress.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3: Sector Erase Timer). The
time-out begins from the rising edge of the final WE# pulse in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are no longer latched. Note
that while the Embedded Erase operation is in progress, the system can read data from the non-erasing bank. The system can
determine the status of the erase operation by reading DQ7, DQ6, DQ2, or RY/BY# in the erasing bank. Refer to Section 16. Write
Operation Status on page 52 for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However,
note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should
be reinitiated once that bank has returned to reading array data, to ensure data integrity.
Figure 2 on page 12 illustrates the algorithm for the erase operation. Refer to the tables in Section 20.5 Erase/Program Operations
on page 64 for parameters, and Figure 21 on page 66 for timing diagrams.
Document Number: 002-00615 Rev. *F
Page 46 of 80
S29PL-J
Figure 10. Erase Operation
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
Embedded
Erase
algorithm
in progress
No
Data = FFh?
Yes
Erasure Completed
15.8 Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data
to, any sector not selected for erasure. The bank address is required when writing this command. This command is valid only during
the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend
command is ignored if written during the chip erase operation or Embedded Program algorithm.
When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 35 µs to suspend
the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately
terminates the time-out period and suspends the erase operation. Addresses are “don’t-cares” when writing the Erase suspend
command.
After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system can read data from or
program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any
address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2
together, to determine if a sector is actively erasing or is erase-suspended. Refer to Section 16. Write Operation Status on page 52
for information on these status bits.
After an erase-suspended program operation is complete, the bank returns to the erase-suspend-read mode. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard Word Program operation.
Refer to Section 16. Write Operation Status on page 52 for more information.
In the erase-suspend-read mode, the system can also issue the autoselect command sequence. The device allows reading autoselect
codes even at addresses within erasing sectors, since the codes are not stored in the memory array. When the device exits the
autoselect mode, the device reverts to the Erase Suspend mode, and is ready for another valid operation. Refer to Table 19 on page
27 and Section 15.3 Autoselect Command Sequence on page 43 for details.
To resume the sector erase operation, the system must write the Erase Resume command (address bits are don’t care). The bank
address of the erase-suspended bank is required when writing this command. Further writes of the Resume command are ignored.
Another Erase Suspend command can be written after the chip has resumed erasing.
Notes
18. See Table 28 on page 49 for erase command sequence.
19. See the section on DQ3 for information on the sector erase timer.
Document Number: 002-00615 Rev. *F
Page 47 of 80
S29PL-J
If the Persistent Sector Protection Mode Locking Bit is verified as programmed without margin, the Persistent Sector Protection Mode
Locking Bit Program Command should be reissued to improve program margin. If the Secured Silicon Sector Protection Bit is verified
as programmed without margin, the Secured Silicon Sector Protection Bit Program Command should be reissued to improve program
margin. µµAfter programming a PPB, two additional cycles are needed to determine whether the PPB has been programmed with
margin. If the PPB has been programmed without margin, the program command should be reissued to improve the program margin.
Also note that the total number of PPB program/erase cycles is limited to 100 cycles. Cycling the PPBs beyond 100 cycles is not
guaranteed.
After erasing the PPBs, two additional cycles are needed to determine whether the PPB has been erased with margin. If the PPBs
has been erased without margin, the erase command should be reissued to improve the program margin. The programming of either
the PPB or DYB for a given sector or sector group can be verified by writing a Sector Protection Status command to the device.
Note that there is no single command to independently verify the programming of a DYB for a given sector group.
15.9 Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming operation so that data can read from any
non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the
programming operation within tPSL (program suspend latency) and updates the status bits. Addresses are “don’t-cares” when writing
the Program Suspend command. After the programming operation has been suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is
suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from
the Secured Silicon Sector area, then user must use the proper command sequences to enter and exit this region. The system may
also write the autoselect command sequence when the device is in Program Suspend mode. The device allows reading autoselect
codes in the suspended sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the
device reverts to Program Suspend mode, and is ready for another valid operation. See Section 15.3 Autoselect Command Sequence
on page 43 for more information. After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See
Section 16. Write Operation Status on page 52 for more information. The system must write the Program Resume command (address
bits are “don’t care”) to exit the Program Suspend mode and continue the programming operation. Further writes of the Program
Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming.
Document Number: 002-00615 Rev. *F
Page 48 of 80
S29PL-J
15.10 Command Definitions Tables
Table 28 contains the Memory Array Command Definitions.
Table 28. Memory Array Command Definitions
Bus Cycles (Notes 20–23)
Command (Notes)
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
[24]
[25]
Read
1
1
RA
RD
F0
Reset
XXX
(BA)
555
(BA)
X00
Manufacturer ID
4
6
4
555
555
555
AA
AA
AA
2AA
2AA
2AA
55
55
55
90
90
90
01
(BA)
555
(BA)
X01
(BA)
X0E
Note
[29]
(BA)
X0F
Note
[29]
[29]
Device ID
227E
Secured Silicon Sector
(BA)
555
X03
Note [27]
[27]
Factory Protect
Sector Group
Protect Verify
(BA)
555
XX00/
XX01
4
555
AAA
2AA
55
90
(SA) X02
[28]
Program
4
6
6
1
1
1
2
3
2
2
1
2
555
555
555
BA
AA
AA
AA
B0
30
98
A0
AA
A0
80
98
90
2AA
2AA
2AA
55
55
55
555
555
555
A0
80
80
PA
555
555
PD
AA
AA
Chip Erase
2AA
2AA
55
55
555
SA
10
30
Sector Erase
[30]
Program/Erase Suspend
[31]
Program/Erase Resume
BA
[32]
CFI Query
55
[33]
Accelerated Program
XX
PA
2AA
PA
PD
55
[33]
Unlock Bypass Entry
555
XX
555
20
[33]
Unlock Bypass Program
PD
10
[33]
Unlock Bypass Erase
XX
XX
[32, 33]
Unlock Bypass CFI
XX
[33]
Unlock Bypass Reset
XXX
XXX
00
Legend
BA = Address of bank switching to autoselect mode, bypass mode, or erase operation. Determined by PL127J: Amax:A20, PL064J: Amax:A19, PL032J: Amax:A18.
PA = Program Address (Amax:A0). Addresses latch on falling edge of WE# or CE# pulse, whichever happens later.
PD = Program Data (DQ15:DQ0) written to location PA. Data latches on rising edge of WE# or CE# pulse, whichever happens first.
RA = Read Address (Amax:A0).
RD = Read Data (DQ15:DQ0) from location RA.
SA = Sector Address (Amax:A12) for verifying (in autoselect mode) or erasing.
WD = Write Data. See “Configuration Register” definition for specific write data. Data latched on rising edge of WE#.
X = Don’t care
Notes
20. See Table 13 for description of bus operations.
21. All values are in hexadecimal.
22. Shaded cells in table denote read cycles. All other cycles are write operations.
23. During unlock and command cycles, when lower address bits are 555 or 2AAh as shown in table, address bits higher than A11 (except where BA is required) and
data bits higher than DQ7 are don’t cares.
24. No unlock or command cycles required when bank is reading array data.
25. The Reset command is required to return to reading array (or to erase-suspend-read mode if previously in Erase Suspend) when bank is in autoselect mode, or if
DQ5 goes high (while bank is providing status information).
26. Fourth cycle of autoselect command sequence is a read cycle. System must provide bank address to obtain manufacturer ID or device ID information. See Section 15.3
Autoselect Command Sequence on page 43 for more information.
27. The data is DQ6=1 for factory and customer locked and DQ7=1 for factory locked.
28. The data is 00h for an unprotected sector group and 01h for a protected sector group.
29. Device ID must be read across cycles 4, 5, and 6. PL127J (X0Eh = 2220h, X0Fh = 2200h), PL064J (X0Eh = 2202h, X0Fh = 2201h), PL032J (X0Eh = 220Ah, X0Fh
= 2201h).
30. System may read and program in non-erasing sectors, or enter autoselect mode, when in Program/Erase Suspend mode. Program/Erase Suspend command is valid
only during a sector erase operation, and requires bank address.
31. Program/Erase Resume command is valid only during Erase Suspend mode, and requires bank address.
32. Command is valid when device is ready to read array data or when device is in autoselect mode.
33. WP#/ACC must be at V during the entire operation of command.
ID
Document Number: 002-00615 Rev. *F
Page 49 of 80
S29PL-J
Table 29. Sector Protection Command Definitions
Bus Cycles (Notes 34-37)
Command (Notes)
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Reset
1
3
XXX
F0
Secured Silicon
Sector Entry
555
555
AA
AA
2AA
2AA
55
55
555
555
88
90
[49]
Secured Silicon
Sector Exit
4
6
XX
OW
OW
00
68
48
[49]
Secured Silicon
Protection Bit
Program
RD
(0)
555
AA
2AA
55
555
60
OW
OW
48
OW
[38, 39]
Secured Silicon
RD
(0)
5
4
4
7
6
4
555
555
555
555
555
555
AA
AA
AA
AA
AA
AA
2AA
2AA
2AA
2AA
2AA
2AA
55
55
55
55
55
55
555
555
555
555
555
60
38
C8
28
60
90
Protection Bit Status
XX
[0-3]
PD
[0-3]
[38, 40, 41]
Password Program
PWA
[0-3]
PWD
[0-3]
[39, 41, 42]
Password Verify
PWA
[0]
PWD
[0]
PWA
[1]
PWD
[1]
PWA
[2]
PWD
[2]
PWA
[3]
PWD
[3]
[40, 43, 44]
Password Unlock
(SA)
WP
(SA)
WP
(SA)
WP
[38, 39, 44]
PPB Program
PPB Status
68
48
RD(0)
BA+55
5
(SA)
WP
RD
(0)
(SA)
WP
[38, 39, 46, 47]
All PPB Erase
6
3
4
555
555
555
AA
AA
AA
2AA
2AA
2AA
55
55
55
555
555
60
78
58
WP
60
(SA)
40
RD(0)
PPB Lock Bit Set
BA+55
5
RD
(1)
[48]
PPB Lock Bit Status
SA
[40]
DYB Write
4
4
555
555
AA
AA
2AA
2AA
55
55
555
555
48
48
SA
SA
X1
X0
[40]
DYB Erase
BA+55
5
RD
(0)
[39]
DYB Status
4
6
5
6
5
555
555
555
555
555
AA
AA
AA
AA
AA
2AA
2AA
2AA
2AA
2AA
55
55
55
55
55
58
60
60
60
60
SA
PL
PL
SL
SL
[38, 39, 45]
[38, 39, 45]
PPMLB Program
555
555
555
555
68
48
68
48
PL
PL
SL
SL
48
PL
SL
RD(0)
RD(0)
RD
(0)
[38]
PPMLB Status
SPMLB Program
48
RD
(0)
[38]
SPMLB Status
Legend
DYB = Dynamic Protection Bit
OW = Address (A7:A0) is (00011010)
PD[3:0] = Password Data (1 of 4 portions)
PPB = Persistent Protection Bit
PWA = Password Address. A1:A0 selects portion of password.
PWD = Password Data being verified.
PL = Password Protection Mode Lock Address (A7:A0) is (00001010)
RD(0) = Read Data DQ0 for protection indicator bit.
RD(1) = Read Data DQ1 for PPB Lock status.
SA = Sector Address where security command applies. Address bits Amax:A12 uniquely select any sector.
SL = Persistent Protection Mode Lock Address (A7:A0) is (00010010)
WP = PPB Address (A7:A0) is (00000010)
X = Don’t care
PPMLB = Password Protection Mode Locking Bit
SPMLB = Persistent Protection Mode Locking Bit
Document Number: 002-00615 Rev. *F
Page 50 of 80
S29PL-J
Notes
34. See Table 13 on page 18 for description of bus operations.
35. All values are in hexadecimal.
36. Shaded cells in table denote read cycles. All other cycles are write operations.
37. During unlock and command cycles, when lower address bits are 555 or 2AAh as shown in table, address bits higher than A11 (except where BA is required) and data
bits higher than DQ7 are don’t cares.
38. The reset command returns device to reading array.
39. Cycle 4 programs the addressed locking bit. Cycles 5 and 6 validate bit has been fully programmed when DQ0 = 1. If DQ0 = 0 in cycle 6, program command must be
issued and verified again.
40. Data is latched on the rising edge of WE#.
41. Entire command sequence must be entered for each portion of password.
42. Command sequence returns FFh if PPMLB is set.
43. The password is written over four consecutive cycles, at addresses 0-3.
44. A 2 µs timeout is required between any two portions of password.
45. A 100 µs timeout is required between cycles 4 and 5.
46. A 1.2 ms timeout is required between cycles 4 and 5.
47. Cycle 4 erases all PPBs. Cycles 5 and 6 validate bits have been fully erased when DQ0 = 0. If DQ0 = 1 in cycle 6, erase command must be issued and verified again.
Before issuing erase command, all PPBs should be programmed to prevent PPB overerasure.
48. DQ1 = 1 if PPB locked, 0 if unlocked.
49. Once the Secured Silicon Sector Entry Command sequence has been entered, the standard array cannot be accessed until the Exit SecSi Sector command has been
entered or the device has been reset.
Document Number: 002-00615 Rev. *F
Page 51 of 80
S29PL-J
16. Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 30
on page 56 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining
whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#,
to determine whether an Embedded Program or Erase operation is in progress or has been completed.
16.1 DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or
completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command
sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7
status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs
the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program
address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then that bank returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or
if the bank enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any
of the sectors selected for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for
approximately 400 µs, then the bank returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address
within a protected sector, the status may not be valid.
When the system detects DQ7 has changed from the complement to true data, it can read valid data at DQ15–DQ0 on the following
read cycles. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ15–
DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on
DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed
the program or erase operation and DQ7 has valid data, the data outputs on DQ15–DQ0 may be still invalid. Valid data on DQ15–
DQ0 will appear on successive read cycles. Table 30 on page 56 shows the outputs for Data# Polling on DQ7. Figure 11 on page 52
shows the Data# Polling algorithm. Figure 23 on page 67 shows the Data# Polling timing diagram.
Figure 11. Data# Polling Algorithm[50, 51]
START
Read DQ7–DQ0
Addr = VA
Yes
DQ7 = Data?
No
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
Yes
DQ7 = Data?
No
PASS
FAIL
Notes
50. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid
address is any non-protected sector address.
51. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5.
Document Number: 002-00615 Rev. *F
Page 52 of 80
S29PL-J
16.2 RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The
RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output,
several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC
.
If the output is low (Busy), the device is actively erasing or programming. This includes programming in the Erase Suspend mode. If
the output is high (Ready), the device is in the read mode, the standby mode, or one of the banks is in the erase-suspend-read mode.
Table 30 on page 56 shows the outputs for RY/BY#.
16.3 DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device
has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE#
pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system
may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 400 µs,
then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device
is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend
mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended.
Alternatively, the system can use DQ7 (see the Section 16.1 DQ7: Data# Polling on page 52).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is
written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete.
Table 30 on page 56 shows the outputs for Toggle Bit I on DQ6. Figure 12 on page 54 shows the toggle bit algorithm. Figure 24
on page 67 in shows the toggle bit timing diagrams. Figure 25 on page 68 shows the differences between DQ2 and DQ6 in graphical
form. See also Section 16.4 DQ2: Toggle Bit II on page 55.
Document Number: 002-00615 Rev. *F
Page 53 of 80
S29PL-J
Figure 12. Toggle Bit Algorithm[52]
START
Read Byte
(DQ7–DQ0)
Address =VA
Read Byte
(DQ7–DQ0)
Address =VA
No
Toggle Bit
= Toggle?
Yes
No
DQ5 = 1?
Yes
Read Byte Twice
(DQ7–DQ0)
Address = VA
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note
52. The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the Section 16.3 DQ6: Toggle Bit
I on page 53 and Section 16.4 DQ2: Toggle Bit II on page 55 for more information.
Document Number: 002-00615 Rev. *F
Page 54 of 80
S29PL-J
16.4 DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase
algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse
in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use
either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended.
DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors
are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 30 on page 56 to compare
outputs for DQ2 and DQ6.
Figure 12 on page 54 shows the toggle bit algorithm in flowchart form, and the Section 16.4 DQ2: Toggle Bit II on page 55 explains
the algorithm. See also the Section 16.3 DQ6: Toggle Bit I on page 53. Figure 24 on page 67 shows the toggle bit timing diagram.
Figure 25 on page 68 shows the differences between DQ2 and DQ6 in graphical form.
16.5 Reading Toggle Bits DQ6/DQ2
Refer to Figure 12 on page 54 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read
DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value
of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If
the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–
DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note
whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is
toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has
successfully completed the program or erase operation. If it is still toggling, the devic did not completed the operation successfully,
and the system must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system
may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous
paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the operation (top of Figure 12).
16.6 DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5
produces a “1,” indicating that the program or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” Only
an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
Under both these conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read
mode if a bank was previously in the erase-suspend-program mode).
Document Number: 002-00615 Rev. *F
Page 55 of 80
S29PL-J
16.7 DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The
sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” See
also Section 15.7 Sector Erase Command Sequence on page 46.
After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure
that the device has accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun;
all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device will accept
additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3
prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might
not have been accepted.
Table 30 shows the status of DQ3 relative to the other status bits.
Table 30. Write Operation Status
Status
DQ7[54]
DQ6
DQ5[53]
DQ3
DQ2[54]
RY/BY#
Embedded Program
Algorithm
DQ7#
Toggle
0
N/A
No toggle
0
Standard
Mode
Embedded Erase
Algorithm
0
1
Toggle
0
0
1
Toggle
Toggle
0
1
Erase
Erase
Suspend- Suspended
No toggle
N/A
Read
Sector
Erase
Suspend
Mode
Non-Erase
Suspended
Sector
Data
Data
Data
Data
Data
1
Erase-Suspend
-Program
DQ7#
Toggle
Invalid
0
N/A
N/A
0
1
Reading within Program
Suspended Sector
Invalid
Invalid
Invalid
Invalid
(Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed)
Program
Suspend
Mode[55]
Reading within
Non-program
Data Data Data Data Data
1
Suspended Sector
Notes
53. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to Section 16.6 DQ5: Exceeded
Timing Limits on page 55 for more information.
54. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
55. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm is in progress. The device outputs array
data if the system addresses a non-busy bank.
Document Number: 002-00615 Rev. *F
Page 56 of 80
S29PL-J
17. Absolute Maximum Ratings
Storage Temperature Plastic Packages
Ambient Temperature with Power Applied
Voltage with Respect to Ground
–65°C to +150°C
–65°C to +125°C
[56]
VCC
–0.5 V to +4.0 V
–0.5 V to +12.5 V
–0.5 V to +10.5 V
–0.5 V to VCC +0.5 V
200 mA
A9, OE#, and RESET#[57]
WP#/ACC[57]
All other pins[56]
Output Short Circuit Current[58]
Figure 13. Maximum Overshoot Waveforms
20 ns
20 ns
20 ns
V
+0.8 V
CC
+2.0 V
V
–0.5 V
–2.0 V
CC
+0.5 V
2.0 V
20 ns
20 ns
20 ns
Maximum Negative Overshoot Waveform
Maximum Positive Overshoot Waveform
Notes
56. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot V to –2.0 V for periods of up to 20 ns. Maximum DC
SS
voltage on input or I/O pins is V +0.5 V. During voltage transitions, input or I/O pins may overshoot to V +2.0 V for periods up to 20 ns. See Figure 13 on page 57.
CC
CC
57. Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is –0.5 V. During voltage transitions, A9, OE#, WP#/ACC, and RESET# may overshoot V to
SS
–2.0 V for periods of up to 20 ns. See Figure 13 on page 57. Maximum DC input voltage on pin A9, OE#, and RESET# is +12.5 V which may overshoot to +14.0 V
for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns.
58. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
59. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum
rating conditions for extended periods may affect device reliability.
Document Number: 002-00615 Rev. *F
Page 57 of 80
S29PL-J
18. Operating Ranges
Operating ranges define those limits between which the functionality of the device is guaranteed.
Industrial (I) Devices
Ambient Temperature (TA)............................ –40°C to +85°C
Wireless (W) Devices
Ambient Temperature (TA)............................ –25°C to +85°C
Supply Voltages
VCC ........................................................................2.7–3.6 V
VIO (see Note)1.65–1.95 V (for PL127J) or 2.7–3.6 V (for all PLxxxJ devices)
Note
60. For all AC and DC specifications, V = V ; contact your local sales office for other V options.
IO
CC
IO
Document Number: 002-00615 Rev. *F
Page 58 of 80
S29PL-J
19. DC Characteristics
Table 31. CMOS Compatible
Parameter
Parameter Description (notes)
Test Conditions
Min
Typ
Max
Unit
ILI
Input Load Current
VIN = VSS to VCC, VCC = VCC max
1.0
35
µA
A9, OE#, RESET#
Input Load Current
ILIT
ILR
ILO
VCC = VCC max; VID= 12.5 V
VCC = VCC max; VID= 12.5 V
µA
µA
µA
Reset Leakage Current
Output Leakage Current
35
V
OUT = VSS to VCC, OE# = VIH
1.0
VCC = VCC max
5 MHz
20
45
15
0.2
0.2
0.2
21
46
21
46
30
55
25
5
ICC1
VCC Active Read Current[61, 62]
OE# = VIH, VCC = VCC max
mA
10 MHz
ICC2
ICC3
ICC4
ICC5
VCC Active Write Current[62, 63]
VCC Standby Current[62]
VCC Reset Current[62]
OE# = VIH, WE# = VIL
mA
µA
µA
µA
CE#, RESET#, WP#/ACC = VIO 0.3 V
RESET# = VSS 0.3 V
5
Automatic Sleep Mode[62, 64]
VIH = VIO 0.3 V; VIL = VSS 0.3 V
5
5 MHz
45
70
45
70
VCC Active Read-While-Program
Current[61, 62]
ICC6
OE# = VIH
,
,
mA
mA
10 MHz
5 MHz
VCC Active Read-While-Erase
Current[61, 62]
ICC7
ICC8
ICC9
VIL
OE# = VIH
OE# = VIH
10 MHz
VCC Active Program-While-Erase-
Suspended Current[62, 65]
VCC Active Page Read Current[62]
17
10
25
15
mA
mA
V
OE# = VIH, 8 word Page Read
IO = 1.65–1.95 V
V
–0.4
–0.5
IO–0.4
2.0
0.4
(PL127J)
Input Low Voltage
V
IO = 2.7–3.6 V
0.8
V
V
IO = 1.65–1.95 V
V
VIO+0.4
VCC+0.3
9.5
V
(PL127J)
VIH
Input High Voltage
V
V
IO = 2.7–3.6 V
V
Voltage for ACC
Program Acceleration
VHH
VID
CC = 3.0 V ± 10%
8.5
V
Voltage for Autoselect and
Temporary Sector Unprotect
VCC = 3.0 V 10%
11.5
12.5
0.1
V
V
V
V
IOL = 100 µA, VCC = VCC min
VIO = 1.65–1.95 V
(PL127J)
,
VOL
Output Low Voltage
IOL = 2.0 mA, VCC = VCC min
VIO = 2.7–3.6 V
,
0.4
IOH = –100 µA, VCC = VCC min
VIO = 1.65–1.95 V
(PL127J)
,
VIO–0.1
VOH
Output High Voltage
IOH = ––100 µA, VIO = VCC min
VCC–0.2V
2.3
V
V
VLKO
Low VCC Lock-Out Voltage[65]
2.5
Notes
61. The I current listed is typically less than 5 mA/MHz, with OE# at V
.
IH
CC
62. Maximum I specifications are tested with V = V .
CC
CC
CCmax
63. I active while Embedded Erase or Embedded Program is in progress.
CC
64. Automatic sleep mode enables the low power mode when addresses remain stable for t
65. Not 100% tested.
+ 30 ns. Typical sleep mode current is 2 µA.
ACC
Document Number: 002-00615 Rev. *F
Page 59 of 80
S29PL-J
20. AC Characteristics
20.1 Test Conditions
Figure 14. Test Setups[66]
3.6 V
2.7 k
Device
Under
Test
Device
Under
Test
C
L
C
6.2 k
L
VIO = 3.0 V
VIO = 1.8 V (PL127J)
Table 32. Test Specifications
Test Conditions
All Speeds
1 TTL gate
30
Unit
Output Load
Output Load Capacitance, CL (including jig capacitance)
pF
ns
VIO = 1.8 V (PL127J)
IO = 3.0 V
VIO = 1.8 V (PL127J)
IO = 3.0 V
Input Rise and Fall Times
Input Pulse Levels
5
V
0.0 - 1.8
0.0–3.0
VIO/2
V
V
Input timing measurement reference levels
Output timing measurement reference levels
V
V
VIO/2
Note
66. Diodes are IN3064 or equivalent.
Document Number: 002-00615 Rev. *F
Page 60 of 80
S29PL-J
20.2 Switching Waveforms
Table 33. Key To Switching Waveforms
Waveform
Inputs
Outputs
Steady
Changing from H to L
Changing from L to H
Don’t Care, Any Change Permitted
Does Not Apply
Changing, State Unknown
Center Line is High Impedance State (High Z)
Figure 15. Input Waveforms and Measurement Levels
VIO
VIO/2
VIO/2
Input
Measurement Level
Output
0.0 V
20.3 Read Operations
Table 34. Read-Only Operations
Parameter
Speed Options
Description (Notes)
Test Setup
Unit
JEDEC
tAVAV
Std.
55
55
55
55
20
20
60
60
60
60
25
25
65
65
65
65
25
70
70
70
70
30
80
80
80
80
30
35
tRC
Read Cycle Time[67]
Min
ns
ns
ns
ns
ns
ns
ns
tAVQV
tELQV
tACC Address to Output Delay
tCE Chip Enable to Output Delay
tPACC Page Access Time
CE#, OE# = VIL Max
OE# = VIL
Max
Max
Max
Max
Max
tGLQV
tEHQZ
tGHQZ
tOE
tDF
tDF
Output Enable to Output Delay
Chip Enable to Output High Z[69]
Output Enable to Output High Z[67, 69]
30
16
16
Output Hold Time From Addresses,
tAXQX
tOH
Min
Min
Min
5
0
ns
ns
ns
CE# or OE#, Whichever Occurs First[69]
Read
Output Enable Hold
tOEH
Time[67]
Toggle and Data#
10
Polling
Notes
67. Not 100% tested.
68. See Figure 14 on page 60 and Table 32 on page 60 for test specifications
69. Measurements performed by placing a 50 ohm termination on the data pin with a bias of V /2. The time from OE# high to the data bus driven to V /2 is taken as t .
DF
CC
CC
70. For 70 pF Output Load Capacitance, 2 ns will be added to the above t
,t ,t
,t values for all speed grades
ACC CE PACC OE
Document Number: 002-00615 Rev. *F
Page 61 of 80
S29PL-J
Figure 16. Read Operation Timings
tRC
Addresses Stable
tACC
Addresses
CE#
tRH
tRH
tD
tOE
OE#
WE
tOEH
tCE
tOH
Valid Data
High Z
High Z
Data
RESET#
RY/BY#
0 V
Figure 17. Page Read Operation Timings
Same Page
Amax
-
-
A3
A0
A2
Ad
Aa
tACC
Ab
tPACC
Ac
tPACC
tPACC
Data
Qa
Qb
Qc
Qd
CE#
OE#
Document Number: 002-00615 Rev. *F
Page 62 of 80
S29PL-J
20.4 Reset
Table 35. Hardware Reset (RESET#)
Parameter
All Speed
Options
Description
Unit
JEDEC
Std
tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode[71]
tReady RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode[71]
Max
Max
Min
Min
Min
Min
20
500
500
50
µs
ns
ns
ns
µs
ns
tRP
tRH
RESET# Pulse Width
Reset High Time Before Read[71]
tRPD RESET# Low to Standby Mode
tRB RY/BY# Recovery Time
20
0
Note
71. Not 100% tested.
Figure 18. Reset Timings
RY/BY#
CE#, OE#
RESET#
tRH
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Document Number: 002-00615 Rev. *F
Page 63 of 80
S29PL-J
20.5 Erase/Program Operations
Table 36. Erase and Program Operations
Parameter
Speed Options (ns)
Description
Unit
JEDEC
tAVAV
Std
tWC
tAS
55
Min 55
Min
60
65
65
0
70
80
Write Cycle Time[72]
Address Setup Time
60
70
80
tAVWL
ns
ns
ns
ns
ns
ns
ns
ns
tASO
tAH
tAHT
tDS
Address Setup Time to OE# low during toggle bit polling
Address Hold Time
Min
15
tWLAX
Min 30
35
30
Address Hold Time From CE# or OE# high during toggle bit polling Min
0
tDVWH
tWHDX
Data Setup Time
Data Hold Time
Min 25
tDH
Min
Min
Min
0
10
0
tOEPH Output Enable High during toggle bit polling
tGHWL
tGHWL Read Recovery Time Before Write
(OE# High to WE# Low)
tELWL
tWHEH
tWLWH
tWHDL
tCS
tCH
CE# Setup Time
Min
Min
0
0
ns
ns
ns
ns
ns
µs
µs
sec
µs
ns
ns
ns
µs
µs
CE# Hold Time
tWP
Write Pulse Width
Write Pulse Width High
Min
35
tWPH
Min 20
Min
25
tSR/W Latency Between Read and Write Operations
0
6
tWHWH1 tWHWH1 Programming Operation[73]
tWHWH1 tWHWH1 Accelerated Programming Operation[73]
tWHWH2 tWHWH2 Sector Erase Operation[73]
Typ
Typ
4
Typ
0.5
50
0
tVCS
tRB
VCC Setup Time[72]
Min
Write Recovery Time from RY/BY#
Min
tBUSY Program/Erase Valid to RY/BY# Delay
Max
Min
90
35
35
35
tPSL
tESL
Program Suspend Latency
Erase Suspend Latency
Max
Max
Notes
72. Not 100% tested.
73. See Table 39 on page 71 for more information.
Document Number: 002-00615 Rev. *F
Page 64 of 80
S29PL-J
20.6 Timing Diagrams
Figure 19. Program Operation Timings[74]
Program Command Sequence (last two cycles) Read Status Data (last two cycles)
tAS
PA
tWC
Addresses
555h
PA
PA
tAH
CE#
OE#
tCH
tWHWH1
tWP
WE#
Data
tWPH
tCS
tDS
tDH
PD
DOUT
A0h
Status
tBUSY
tRB
RY/BY#
VCC
tVCS
Figure 20. Accelerated Program Timing Diagram
VHH
VIL or VIH
VIL or VIH
WP#/ACC
tVHH
tVHH
Note
74. PA = program address, PD = program data, D
is the true data at the program address.
OUT
Document Number: 002-00615 Rev. *F
Page 65 of 80
S29PL-J
Figure 21. Chip/Sector Erase Operation Timings[75]
Erase Command Sequence (last two cycles)
Read Status Data
tAS
SA
tWC
VA
Addresses
CE#
2AAh
VA
555h for chip erase
tAH
tCH
OE#
tWP
WE#
tWPH
tWHWH2
tCS
tDS
tDH
Data
Status
D
OUT
55h
30h
10 for Chip Erase
tBUSY
tRB
RY/BY#
VCC
tVCS
Figure 22. Back-to-back Read/Write Cycle Timings
tWC
tWC
tRC
tWC
Valid PA
tAH
Valid RA
Valid PA
Valid PA
Addresses
tAS
tAS
tCPH
tAH
tACC
tCE
CE#
OE#
tCP
tOE
tOEH
tGHWL
tWP
WE#
Data
tDF
tWPH
tDS
tOH
tDH
Valid
Out
Valid
In
Valid
In
Valid
In
tSR/W
WE# Controlled Write Cycle
Read Cycle
CE# Controlled Write Cycles
Note
75. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Section 16. Write Operation Status on page 52).
Document Number: 002-00615 Rev. *F
Page 66 of 80
S29PL-J
Figure 23. Data# Polling Timings (During Embedded Algorithms)[76]
tRC
Addresses
CE#
VA
tACC
tCE
VA
VA
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
High Z
DQ7
Valid Data
Complement
Complement
True
DQ6–DQ0
Status Data
True
Valid Data
Status Data
tBUSY
RY/BY#
Figure 24. Toggle Bit Timings (During Embedded Algorithms)[77]
tAHT
tAS
Addresses
CE#
tAHT
tASO
tCEPH
tOEH
WE#
OE#
tOEPH
tDH
tOE
Valid
Status
Valid
Status
Valid
Status
Valid Data
DQ6/DQ2
RY/BY#
Valid Data
(first read)
(second read)
(stops toggling)
Notes
76. VA = Valid address. The illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.
77. VA = Valid address; not required for DQ6. The illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle.
Document Number: 002-00615 Rev. *F
Page 67 of 80
S29PL-J
Figure 25. DQ2 vs. DQ6[78]
Enter
Embedded
Erasing
Erase
Suspend
Enter Erase
Suspend Program
Erase
Resume
Erase
Erase Suspend
Read
Erase
Suspend
Program
Erase
Complete
WE#
Erase
Erase Suspend
Read
DQ6
DQ2
21. Protect/Unprotect
Table 37. Temporary Sector Unprotect[79]
Parameter
Description
All Speed Options
Unit
JEDEC
Std
tVIDR
tVHH
tRSP
tRRB
VID Rise and Fall Time (See Note)
VHH Rise and Fall Time (See Note)
Min
500
250
4
ns
ns
µs
Min
Min
RESET# Setup Time for Temporary Sector Unprotect
RESET# Hold Time from RY/BY# High for Temporary
Sector Unprotect
Min
4
µs
Note
79. Not 100% tested.
Figure 26. Temporary Sector Unprotect Timing Diagram
VID
VID
RESET#
VIL or VIH
VIL or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
Note
78. DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6.
Document Number: 002-00615 Rev. *F
Page 68 of 80
S29PL-J
Figure 27. Sector/Sector Block Protect and Unprotect Timing Diagram[80]
VID
VIH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Valid*
Status
Sector Group Protect/Unprotect
Verify
40h
Data
60h
60h
1 µs
Sector Group Protect: 150 µs
Sector Group Unprotect: 15 ms
CE#
WE#
OE#
21.1 Controlled Erase Operations
Table 38. Alternate CE# Controlled Erase and Program Operations
Parameter
Speed Options
Description (Notes)
Unit
80
JEDEC
tAVAV
Std
tWC
tAS
tAH
tDS
tDH
55
60
60
65
65
0
70
70
Write Cycle Time[81, 82]
Address Setup Time
Address Hold Time
Data Setup Time
Min
Min
Min
Min
Min
55
80
ns
ns
ns
ns
ns
tAVWL
tELAX
tDVEH
tEHDX
30
25
35
30
Data Hold Time
0
0
Read Recovery Time Before Write (OE# High to
WE# Low)
tGHEL
tGHEL
Min
ns
tWLEL
tEHWH
tELEH
tWS
tWH
tCP
WE# Setup Time
WE# Hold Time
Min
Min
Min
Min
Typ
Typ
Typ
0
0
ns
ns
CE# Pulse Width
35
20
40
25
ns
tEHEL
tCPH
CE# Pulse Width High
ns
tWHWH1
tWHWH1
tWHWH2
tWHWH1 Programming Operation[82]
tWHWH1 Accelerated Programming Operation[82]
tWHWH2 Sector Erase Operation[82]
6
4
µs
µs
sec
0.5
Notes
81. Not 100% tested.
82. See Section 39 Erase And Programming Performance on page 71 for more information.
Note
80. For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0.
Document Number: 002-00615 Rev. *F
Page 69 of 80
S29PL-J
Figure 28. Alternate CE# Controlled Write (Erase/Program) Operation Timings[83, 84, 85]
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tWH
tAS
tAH
WE#
OE#
tGHEL
tWHWH1 or 2
tCP
CE#
Data
tWS
tCPH
tDS
tBUSY
tDH
DQ7#
DOUT
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Figure 29. Timing Diagram for Alternating Between CE1# and CE2# Control
CE1#
tCCR
tCCR
CE2#
Notes
83. Figure indicates last two bus cycles of a program or erase operation.
84. PA = program address, SA = sector address, PD = program data.
85. DQ7# is the complement of the data written to the device. D
is the data written to the device.
OUT
Document Number: 002-00615 Rev. *F
Page 70 of 80
S29PL-J
Table 39. Erase And Programming Performance
Parameter
Sector Erase Time
PL127J
Typ[86]
0.5
135
71
Max[87]
5
Unit
sec
sec
sec
sec
µs
Comments
216
113.6
62.4
100
60
Excludes 00h programming prior to
erasure[89]
Chip Erase Time
PL064J
PL032J
39
Word Program Time
6
Excludes system level overhead[90]
Accelerated Word Program
4
µs
PL127J
PL064J
PL032J
50.4
25.2
12.6
200
50.4
25.2
sec
sec
sec
Chip Program Time[88]
Notes
86. Typical program and erase times assume the following conditions: 25°C, 3.0 V V , 100,000 cycles. Additionally, programming typicals assume checkerboard pattern.
CC
All values are subject to change.
87. Under worst case conditions of 90°C, V = 2.7 V, 1,000,000 cycles. All values are subject to change.
CC
88. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster than the maximum program
times listed.
89. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
90. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 28 on page 49 for further information
on command definitions.
91. The device has a minimum erase and program cycle endurance of 100,000 cycles.
Document Number: 002-00615 Rev. *F
Page 71 of 80
S29PL-J
22. Pin Capacitance
22.1 BGA Pin Capacitance
Parameter Symbol
Parameter Description
Test Setup
VIN = 0
Typ
6.3
7.0
5.5
11
Max
7
Unit
pF
CIN
COUT
CIN2
CIN3
Input Capacitance
Output Capacitance
VOUT = 0
VIN = 0
8
pF
Control Pin Capacitance
WP#/ACC Pin Capacitance
8
pF
VIN = 0
12
pF
Notes
92. Sampled, not 100% tested.
93. Test conditions T = 25°C, f = 1.0 MHz.
A
22.2 TSOP Pin Capacitance
Parameter Symbol
Parameter Description
Test Setup
VIN = 0
Typ
10
Max
10.5
6.5
10
Unit
pF
CIN
COUT
CIN2
CIN3
Input Capacitance
Output Capacitance
VOUT = 0
VIN = 0
5.5
8
pF
Control Pin Capacitance
WP#/ACC Pin Capacitance
pF
VIN = 0
9.5
10
pF
Notes
94. Sampled, not 100% tested.
95. Test conditions T = 25°C, f = 1.0 MHz.
A
Document Number: 002-00615 Rev. *F
Page 72 of 80
S29PL-J
23. Physical Dimensions
Figure 30. VBG080—80-Ball Fine-pitch Ball Grid Array 8 × 11 mm Package (PL127J)
002-25352 Rev. **
Document Number: 002-00615 Rev. *F
Page 73 of 80
S29PL-J
Figure 31. VBH064—64-Ball Fine-pitch Ball Grid Array 8 × 11.6 mm package (PL127J)
002-28179 Rev. **
Document Number: 002-00615 Rev. *F
Page 74 of 80
S29PL-J
Figure 32. VBK048—48-Ball Fine-pitch Ball Grid Array 8.15 × 6.15 mm package (PL032J and PL064J)
002-19063 Rev. **
Document Number: 002-00615 Rev. *F
Page 75 of 80
S29PL-J
Figure 33. VBU056—56-Ball Fine-pitch BGA 7 × 9mm package (PL064J and PL032J)
NOTES:
DIMENSIONS
1.
2.
3.
DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 .
ALL DIMENSIONS ARE IN MILLIMETERS .
SYMBOL
MIN.
NOM.
MAX.
1.00
A
-
-
-
BALL POSITION DESIGNATION PER JEP95, SECTION 3, SPP-010/020.
A1
D
0.17
-
4.
5.
e
REPRESENTS THE SOLDER BALL GRID PITCH .
9.00 BSC.
SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D" DIRECTION.
E
7.00 BSC.
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE "E" DIRECTION.
n IS THE TOTAL NUMBER OF POPULATED SOLDER BALLS FOR MATRIX SIZE MD AND ME.
D1
E1
5.60 BSC.
5.60 BSC.
6
7
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C.
8
8
MD
ME
"SD" AND "SE" ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE
POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW.
n
56
-
Øb
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW, "SD" OR "SE" = 0.
0.33
0.45
eD/eE
SD/SE
0.80 BSC.
0.40 BSC.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, "SD" = eD/2 and "SE" = eE/2.
8.
9
"+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS.
A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK, METALLIZED
MARK INDENTATION OR OTHER MEANS.
002-15551 Rev. **
Document Number: 002-00615 Rev. *F
Page 76 of 80
S29PL-J
Figure 34. TS056—20 × 14 mm, 56-pin TSOP (PL127J)
NOTES:
DIMENSIONS
SYMBOL
1. DIMENSIONS ARE IN MILLIMETERS (mm).
MIN. NOM. MAX.
A
1.20
2. PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
0.15
0.05
A1
A2
b1
b
3. PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN): INK OR LASER MARK.
0.95
0.17
0.17
1.00
0.20
1.05
0.23
0.27
4. TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
0.22
5. DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
c1
0.10
0.10
0.16
0.21
MOLD PROTRUSION ON E IS 0.15mm PER SIDE AND ON D1 IS 0.25mm PER SIDE.
c
D
6. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08mm TOTAL IN EXCESS OF b DIMENSION AT MAX.
MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON LOWER RADIUS OR
THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD
TO BE 0.07mm .
20.00 BASIC
18.40 BASIC
14.00 BASIC
0.50 BASIC
D1
E
e
L
0
0.50
0.60 0.70
7. THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10mm AND 0.25mm FROM THE LEAD TIP.
0°
8
0.20
R
N
0.08
8. LEAD COPLANARITY SHALL BE WITHIN 0.10mm AS MEASURED FROM THE
SEATING PLANE.
56
9. DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
10. JEDEC SPECIFICATION NO. REF: MO-142(D)EC.
002-15549 Rev. *B
Document Number: 002-00615 Rev. *F
Page 77 of 80
S29PL-J
22. Document History Page
Document Title: S29PL-J, 128-/64-/32-Mbit (8/4/2M × 16-Bit), 3 V, Flash with Enhanced VersatileIO™
Document Number: 002-00615
Orig. of
Change
Rev.
ECN No.
Submission Date
Description of Change
Initial release
Included backward compatibility with MBM29xx families.
48-ball BGA package is not supported and was removed.
Model numbers for the 48-ball BGA configurations were removed.
An illustration was added to show the pin-out configuration.
Added the description of 01h for address 4Fh and removed the 0004 data.
Provided the time units of measure for the erase and programming performances.
Corrected typo in device ID.
Added 3V VIO for PL064J and PL032J devices.
Corrected the voltage rating, ball configuration, and physical dimensions for model numbers 12 and
13.
Removed the 64-ball, 8x9 mm diagram.
Clarified the supply voltages that apply to the PL127J/PL129J and all other PLxxxJ
products.
Added information applicable to the CIN3 symbol.
Removed the 9x8 mm package drawing.
Added the 56-ball 7x9 mm pinout diagram.
Updated to include the 8 x 6 mm, 48-ball Fine pitch BGAand 7 x 9 mm, 56-ball Fine-pitch BGAoptions.
Added the VBK048 package drawing.
Changed names.
Updated specs in this table.
Updated the Model Number offerings.
Corrected the Package Markings for the 64-ball FBGA packages.
Added combinations for the TLC056 package on the PL064J and PL032J devices.
Valid Combinations for BGA Packages (128Mb)
Package Options
Added the 7 x 9mm 56-ball package.
56-ball connection diagram
Notes 1 and 2 corrected to reflect accurate temperature ranges and cycling.
Updated the Model Number offerings
Updated the Package Types information.
Figure 6, In-System Sector Protection/Sector Unprotection Algorithms
Program Suspend/Program Resume Commands
New section added. Made global changes to include program suspend/resume commands.
Added Erase Suspend Latency.
Updated table and added a notes section.
01/29/2004 to
04/18/2013
Added the VBU056 package
**
RYSU
Added note: When Polling the SecSi indicator bit the A21 to A12 should be set within the address
range 004000h-03FFFFh.
Added sentence: Once the Enter Secured Silicon Sector Command sequence has been entered, the
standard array cannot be accessed until the Exit Secured Silicon Sector command has been entered
or the device has been reset.
Added note 16: Once the Secured Silicon Sector Entry Command sequence has been entered, the
standard array cannot be accessed until the Exit Secured Silicon Sector command has been entered
or the device has been reset.
Content the same, tables consolidated to match Ordering Information Descriptions
Consolidated Special Package Handling Instructions and put the information before the
package/pinout descriptions.
Added Figure numbers to the connection diagram graphics.
Updated operating temperatures.
Updated VOH parameter.
Added tESL parameter
Updated the product that uses this package from PL127J to PL064J and PL032J
64-Ball Fine-Pitch BGA—MCP Compatible—PL127JChanged ball F9 to A22
Pin DescriptionCorrected WP#/ACC description.
GlobalChanged data sheet status from Advanced Information to Full Production
Ordering InformationModified/Added note to the Valid Combinations to be Supported for this Device
tables
VCC Ramp RateRemoved Section
Connection DiagramCorrected 64-Ball Fine-Pitch BGA ball description (H9 and L5)
Ordering InformationUnder Package Type, changed wording of “Lead (Pb)-free compliant” material
type to “Standard”.
GlobalRemoved 55 ns as a valid speed supported by PL127J.
Product Selector GuideCorrected the 55 ns Speed Option's Max Page Access and Max OE# Access
time from 2 to 20 ns.
Corrected the 65 ns Speed Option's Max Access and Max CE# Access time from 25 to 65 ns.
Dynamic Protection Bit (DYB)Corrected reference to Table 17 to Table 10.15.
Erase Suspend/Erase Resume CommandsCorrected “This command is valid only during
the sector erase operation, including the 80 µs time-out period...” to “This command is
valid only during the sector erase operation, including the 50 µs time-out period...”.
Command Definitions TablesIn Table 15.2, corrected the value of the third bus cycle of
the “PPB Status”, “PPB Lock Bit Status” and “DYB Status” commands from 555 to
BA+555.
Document Number: 002-00615 Rev. *F
Page 78 of 80
S29PL-J
Document Title: S29PL-J, 128-/64-/32-Mbit (8/4/2M × 16-Bit), 3 V, Flash with Enhanced VersatileIO™
Document Number: 002-00615
Orig. of
Change
Rev.
ECN No.
Submission Date
Description of Change
Absolute Maximum RatingsCorrected the A9, OE# and RESET# “Voltage with Respect to Ground”
maximum range value from +13.0V to +12.5V.
01/29/2004 to
04/18/2013
DQ6: Toggle Bit ICorrected Figure 16.2: Toggle Bit Algorithm.
** (cont'd)
*A
-
RYSU
Pin CapacitanceAdded TSOP package pin capacitance values.
Ordering InformationFor model number 13, corrected “56-ball” TSOP package description to “56-pin”.
GlobalChanged 65 ns and 70 ns initial access time for VIO=1.8V to 80 ns.
4959015
RYSU
10/13/2015
08/10/2016
Updated to Cypress template.
Updated Section 3. Ordering Information on page 6:
Added 1.8V V TSOP package.
IO
Updated Valid Combinations - Standard:
Added 14 in “Additional Ordering Options” column in “128 Mb Products Based on 110 nm Floating
Gate Technology”.
*B
*C
5398456
5644215
NFB
Updated to new template.
Updated Section 3. Ordering Information on page 6:
Removed “BA” and “TA” details under “Package Type”.
Updated Valid Combinations - Standard:
Removed “BA” and “TA” related information.
Updated to new template.
SZZX
02/27/2017
Completing Sunset Review.
*D
*E
5755150
6381371
NIBK
PRIT
05/31/2017
12/05/2018
Updated Cypress Logo and Copyright.
Updated Section 3. Ordering Information on page 6.
Updated Max Sector Erase Time.
Updated Section 23. Physical Dimensions on page 73.
Removed S29PL129J MCP Device.
Added Automotive Device: A = Automotive, AEC-Q100 Grade 3 (-40°C to +85°C).
*F
6654238
BWHA
08/20/2019
Updated Cypress template.
Document Number: 002-00615 Rev. *F
Page 79 of 80
S29PL-J
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
®
Products
PSoC Solutions
Arm® Cortex® Microcontrollers
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/iot
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
Automotive
Cypress Developer Community
Clocks & Buffers
Interface
Community | Projects | Video | Blogs | Training | Components
Technical Support
Internet of Things
Memory
cypress.com/support
cypress.com/memory
cypress.com/mcu
Microcontrollers
PSoC
cypress.com/psoc
cypress.com/pmic
cypress.com/touch
cypress.com/usb
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
cypress.com/wireless
© Cypress Semiconductor Corporation, 2004-2019. This document is the property of Cypress Semiconductor Corporation and its subsidiaries ("Cypress"). This document, including any software or
firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress
reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property
rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants
you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce
the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or
indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by
Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing
device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such
as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING
CYPRESS PRODUCTS, WILLBE FREE FROM CORRUPTION,ATTACK, VIRUSES, INTERFERENCE, HACKING, DATALOSS OR THEFT, OR OTHER SECURITYINTRUSION (collectively, "Security
Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In
addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted
by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or
circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the
responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device"
means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other
medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk
Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of
a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents, affiliates, distributors, and assigns harmless from
and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress
product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i)
Cypress's published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to
use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-00615 Rev. *F
Revised August 20, 2019
Page 80 of 80
相关型号:
©2020 ICPDF网 联系我们和版权申明