TLE4959-5U-SP [INFINEON]

The Infineon XENSIV TLE4959-5U-SP is an integrated differential Hall speed sensor ideally suited for transmission applications. The sensors´ basic function is to provide information about rotational speed and direction of rotation to the transmission control unit. The product includes a sophisticated algorithm which actively suppresses vibration while keeping excellent airgap performance. The product is qualified for automotive usage. ;


型号：	TLE4959-5U-SP
厂家：	Infineon
描述：	The Infineon XENSIV TLE4959-5U-SP is an integrated differential Hall speed sensor ideally suited for transmission applications. The sensors´ basic function is to provide information about rotational speed and direction of rotation to the transmission control unit. The product includes a sophisticated algorithm which actively suppresses vibration while keeping excellent airgap performance. The product is qualified for automotive usage.
文件：	总14页 (文件大小：455K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TLE4959-5U-SP Transmission Speed

Sensor

Features

•

Hall based differential speed sensor

High magnetic sensitivity

Large operating airgap

Dynamic self-calibration principle

Adaptive hysteresis

High vibration suppression capabilities

Three wire voltage interface

Magnetic encoder and ferromagnetic wheel application

High immunity against ESD, EMC and mechanical stress, improved voltage dropout capability

Automotive operating temperature range

4-pin package PG-SSO-4-1

Green Product (RoHS compliant)

AEC Qualified

Applications

The TLE4959-5U-SP is an integrated differential Hall speed sensor ideally suited for transmission applications.

Its basic function is to provide information about rotational speed and direction of rotation to the

transmission control unit. TLE4959-5U-SP includes a sophisticated algorithm which actively suppresses

vibration while keeping excellent airgap performance.

Table 1

Type

Description

Marking

Ordering Code

Package

TLE4959-5U-SP

59AYA2

SP004842810

PG-SSO-4-1

Data Sheet

www.infineon.com/sensors

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Description

The TLE4959-5U-SP comes in a RoHs compliant four-pin package, qualified for automotive usage. the

recommended capacitors increase the EMC robustness of the device. In 12 V applications it is further

recommended to use a serial resistor R_Supplyfor protection on the supply line. A pull-up resistor R_Loadis

mandatory on the output pin and determines the maximum current flowing through the output transistor. A

value of 1.2 kΩ is recommended for the 5V application. (see Figure 1)

Option for 12V

V_pullup

R_LOAD

V_S

R_Supply

100 ...330Ω

R_Q

1.2 kΩ

V_DD

150 ... 220Ω

I_Q

GND

100...470nF

V_Q

1.8 ... 4.7nF

Figure 1

Typical Application Circuit

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Functional Description

The differential Hall sensor IC detects the motion of tooth and magnet encoder applications. To detect the

motion of ferromagnetic objects, the magnetic field must be provided by a back biasing permanent magnet.

Either south or north pole of the magnet can be attached to the rear unmarked side of the IC package (See

Figure 2). The magnetic measurement is based on three equally spaced Hall elements, integrated on the IC.

Both magnetic and mechanical offsets are cancelled by a self calibration algorithm.

1.1

Definition of the Magnetic Field Direction

The magnetic field of a permanent magnet exits from the north pole and enters the south pole. If a north pole

is attached to the backside of the High End Transmission Sensor, the field at the sensor position is positive, as

shown in Figure 2.

Notch

Tooth

Notch

Tooth

Notch

IC Branded

Side

IC Branded

Side

Figure 2

Definition of the Positive Magnetic Field Direction

1.2

Block Diagram

PMU:

V_DD

Chopper switches

Separated supplies

Bandgap (Temp. Compensated)

GND

Digital-Core:

Min/Max-detection

Offset-calculation

Compensated

Amplifier and

Tracking ADC

Diff. Hall

Speed-sensing

Hysteresis-calculation

Offset compensation

Direction detection

Vibration suppression

Output-protocol

Open

Drain

Hall

Direction-

sensing

Compensated

Amplifier and

Tracking ADC

Figure 3

Block Diagram

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Functional Description

1.3

Basic Operation

The speed signal calculated out of the differential hall elements, is amplified, filtered and digitized. An

algorithm in the digital core for peak detection and offset calculation will be executed. The offset is fed back

into the speed signal path with a digital to analog converter for offset correction. During uncalibrated mode,

the output of the speed pulse is triggered in the digital core by exceeding a certain threshold of the tracking

ADC. In calibrated mode the output is triggered by the visible hysteresis.

The direction signal is calculated out of center Hall signals. The direction signal is amplified, filtered, and

digitized. In the digital core the direction and the vibration detection information is determined and the

output protocol is issued.

1.4

Uncalibrated and Calibrated Mode

After power on the differential magnetic speed signal is tracked by an analog to digital converter (Tracking

ADC) and monitored within the digital core. If the signal slope is identified as a rising edge or falling edge, the

first output pulse is triggered. A second trigger pulse is issued with direction information.

In uncalibrated mode, the output protocols are triggered by the DNC (detection noise constant) in the speed

path. After start up the sensor switches with the DNC min value and after that the DNC is adapted to the

magnetic input signal amplitude.

The offset update starts if two valid extrema values are found and the direction of the update has the same

orientation as the magnetic signal. For example, a positive offset update is being issued on a rising magnetic

edge only. After a successful offset correction, the sensor is in calibrated mode. Switching occurs at the

adaptive hysteresis threshold level.

In calibrated mode, the DNC is adapted to magnetic input signal amplitude with a minimum of

ΔB_limit. The output pulses are then triggered with adaptive hysteresis.

1.5

Hysteresis Concept

The adaptive hysteresis is linked to the input signal. Therefore, the system is able to suppress switching if

vibration or noise signals are smaller than the adaptive hysteresis levels. The typical value for the hysteresis

level is 1/4 of the magnetic input signal amplitude, the minimum hysteresis level is ΔB_limit

The visible hysteresis keeps the excellent performance in large pitch transmission application wheels.

Hysteresis = 0.25 * ΔB_pp(peak to peak )

magnetic input signal

hysteresis HI

hysteresis LO

ΔB_z,diff

-2

-4

-6

-8

-10

0.01

0.02

0.03

0.04

0.05

0.06

0.07

time [s]

Figure 4

Adaptive Hysteresis

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Functional Description

1.6

Vibration Suppression

The direction signal is digitized by an analog to digital converter (direction ADC) and fed into the digital core.

Depending upon the rotation direction of the target wheel, the signal of the center probe anticipates or lags

behind for 90°. This phase relationship is evaluated and converted into rotation direction information by

sampling the signal of the center probe in the proximity of the zero crossing of the “speed” bridge signal.

The first pulse after power has a different length to signalize that there is no direction information available.

The magnetic signal amplitude and the direction information are used for detection of parasitic magnetic

signals. Unwanted magnetic signal can be caused by angular or air gap vibrations. If an input signal is

identified as a vibration the output pulse will be suppressed.

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

General Characteristics

2.1

Absolute Maximum Ratings

Table 2

Absolute Maximum Ratings

Parameter

Symbol

Values

Typ. Max.

Unit Note or Test Condition

Min.

Supply voltage without V_DD

supply resistor

-16

–

°C

continuous, T_J≤ 175°C

max. 60 s, T_J≤ 175°C

-18

-1.0

-0.3

–

max. 60 s, T_J≤ 175°C

Output OFF voltage

Output ON voltage

V_{Q_OFF}

V_{Q_ON}

–

max. 1 h,T_Amb≤ 40°C

26.5

continuous, T_J≤ 175°C

continuous, T_Amb≤ 40°C

max. 1 h, T_Amb≤ 40°C

–

26.5

185

max. 60 s, T_Amb≤ 40°C

exposure time: max. 10 × 1 h, V_DD= 16V

Junction temperature

range

T_J

-40

Magnetic field induction B_Z

-5

–

magnetic pulse during magnet

magnetization.

Valid 10 s with T_ambient≤ 80°C

ESD compliance

ESD_HBM

-2

–

HBM¹⁾

1) ESD susceptibility, HBM according to EIA/JESD 22-A114B

Note:

Stresses above the max values listed here may cause permanent damage to the device. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability. Maximum

ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to

the integrated circuit.

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

General Characteristics

2.2

Operating Range

All parameters specified in the following sections refer to these operating conditions unless otherwise

specified.

Table 3

General Operating Conditions

Symbol

Parameter

Values

Unit Note or Test Condition

Min. Typ. Max.

Supply voltage without supply

resistance R_s

V_DD

4.0

–

Continuous Output Off voltage

V_{Q_OFF}

–

Supply voltage power- up/down

voltage ramp

dV_DD/dt

3.0

1e4 V/ms

Supply current

I_DD

I_{Q_ON}

8.0

–

13.4 mA

Continuous output On current

Magnetic signal frequency range

mA V_{Q_LOW}< 0.5 V

kHz

Dynamic range of the magnetic field DR_{mag_field_s}-120

120 mT

of the differential speed channel

Dynamic range of the magnetic field DR_{mag_field_dir}-60

of the direction channel

–

60 mT

Static range of the magnetic field of SR_{mag_field_s}

550 mT

450 mT

the outer Hall probes

Static range of the magnetic field of DR_{mag_field_dir}-100

the center Hall probe

Allowed static difference between

outer probes

SR_{mag_field_diff}-30

Normal operating junction

temperature

T_J

-40

175 °C

185 °C

exposure time: max. 2500 h

at T_J= 175°C, V_DD= 16 V

exposure time: max.

10 × 1 h at T_J= 185°C,

_DD= 16 V, additive to other

lifetime

Not operational lifetime

T_no

-40

150 °C

without sensor function;

exposure time max 500 h @

150°C; increased time for

lower temperatures

according to Arrhenius-

Model, additive to other

lifetime

Temperature compensation range TC

of magnetic material

-800

ppm internal compensation of

magnetic signal amplitude

of speed signal

Note:

In the operating range the functions given in the functional description are fulfilled

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Electrical and Magnetic Characteristics

All values specified at constant amplitude and offset of input signal, over operating range, unless otherwise

specified. Typical values correspond to V_S= 5 V and T_Amb.= 25°C

Table 4

Electrical and Magnetic Parameters

Symbol

Parameter

Values

Unit

Note or Test Condition

Min. Typ.

Max.

500

–

Output saturation voltage

V_Qsat

I_Q≤ 15 mA

Clamping voltage V_DD-Pin

V_{DD_clamp}

leakage current through ESD

diode < 0.5mA

Clamping voltage V_Q-Pin

V_Qclamp

leakage current through ESD

diode < 0.5mA

Reset voltage

V_{DD_reset}

I_Qleak

2.8

3.6

Output leakage current

0.1

µA

V_Q= 18 V

Output current limit during

short-circuit condition

I_Qshort

Junction temperature limit for T_prot

output protection

190

0.8

205

°C

Power on time

t_{power_on}

0.9

µs

during this time the output is

locked to high.

Delay time between magnetic t_delay

signal switching point and

corresponding output signal

falling edge switching event

Output fall time

t_fall

2.0

3.2

2.5

4.5

–

3.0

5.8

µs

V_Pullup= 5 V, R_Pullup= 1.2 kΩ (+/-

10%), C_Q= 1.8 nF (+/-15%),

valid between 80% - 20%

_Pullup= 5 V, R_Pullup= 1.2 kΩ (+/-

10%), C_Q= 1.8 nF (+/-15%),

valid between 90% - 10%

Output rise time

t_rise

11.4 µs

1.78 mT

R_Pullup= 1.2 kΩ (+/-10%),

C_Q= 1.8 nF (+/-15%),

valid between 10% - 90%

Digital noise constant of speed DNC_min

1.22

1.5

channel during start up

Duty Cycle in calibrated mode ²⁾Dty

-1

-1.1

–

on sinusoidal signals

Period Jitter, f ≤ 8 kHz³⁾

Period Jitter, 8kHz≤f ≤10kHz²⁾Jit_10kHz

Jit_8kHz

–

1 sigma, ΔB_pkpk= 3mT

in forward rotational direction

1.1

Number of wrong pulses at

start-up

n_Start

–

in backward rotational

direction

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Electrical and Magnetic Characteristics

Table 4

Electrical and Magnetic Parameters (cont’d)

Parameter

Symbol

Values

Min. Typ.

Unit

Note or Test Condition

Max.

Global run out⁴⁾

Runout_glob

–

of magnetic speed signal

amplitude

al,speed

–

of magnetic speed signal

amplitude with reduced

performance on stop-start-

functionality

Runout_glob

–

of magnetic direction signal

amplitude

al,dir

of magnetic direction signal

amplitude with reduced

performance on stop-start-

functionality

Tooth to tooth run out (peak to Runout_tooth

–

of magnetic speed signal

amplitude

peak variation on two

,speed

consecutive teeth / pole-pair)³⁾

Runout_tooth

of magnetic direction signal

amplitude

,dir

1) Application parameter, IC shall not increase the rise time, Values are calculated and not tested

2) During fast offset alterations, due to the calibration algorithm, exceeding the specified duty cycle is permitted for

short time periods. Parameter not subject to production test, verify by design/characterization.

3) Parameter not subject to productive test. Verified by lab characterization based on jitter-measurement > 1000

periods

4) Defined as 1-(amplitude_min/amplitude_max)

Note:

The listed Electrical and magnetic characteristics are ensured over the operating range of the

integrated circuit. Typical characteristics specify mean values expected over the production spread.

If not other specified, typical characteristics apply at T_Amb= 25°C and V_S= 5 V.

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Package Information

Pure tin covering (green lead plating) is used. The product is RoHS (Restriction of Hazardous Substances)

compliant and marked with letter G in front of the data code marking and may contain a data matrix code on

the rear side of the package (see also information note 136/03). Please refer to your key account team or

regional sales if you need further information.

The specification for soldering and welding is defined in the latest revision of application note

“Recommendation for Board Assembly-Hallsensor SSO Packages”.

4.1

Package Outline

Figure 5

PG-SSO-4-1 (Plastic Green Single Slim Outline), Package Dimensions

Figure 6

Position of the Hall Elements and distance to the branded Side

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Package Information

4.2

Marking and Data Matrix Code

Figure 7

Table 5

Marking of PG-SSO-4-1 Package

Pin Description

Pin Number¹⁾

Symbol

V_DD

Function

Supply Voltage

Ground

GND

Ground

Open Drain Output

1) Refer to frontside view: leftmost pin corresponding to pin number 1

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Package Information

4.3

Packing Information

Figure 8

PG-SSO-4-1 Ammopack

Data Sheet

Ver. 1.0

2019-07

TLE4959-5U-SP Transmission Speed Sensor

Revision History

Version Date

Changes

1.0

2019-07

First version of released datasheet

Data Sheet

Ver. 1.0

2019-07

Please read the Important Notice and Warnings at the end of this document

Trademarks of Infineon Technologies AG

µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,

DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,

HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,

OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,

SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.

Trademarks updated November 2015

Other Trademarks

All referenced product or service names and trademarks are the property of their respective owners.

IMPORTANT NOTICE

The information given in this document shall in no For further information on technology, delivery terms

Edition 2019-07

Published by

Infineon Technologies AG

81726 Munich, Germany

event be regarded as a guarantee of conditions or and conditions and prices, please contact the nearest

characteristics ("Beschaffenheitsgarantie").

Infineon Technologies Office (www.infineon.com).

With respect to any examples, hints or any typical

values stated herein and/or any information regarding

the application of the product, Infineon Technologies

hereby disclaims any and all warranties and liabilities

of any kind, including without limitation warranties of

non-infringement of intellectual property rights of any

third party.

In addition, any information given in this document is

subject to customer's compliance with its obligations

stated in this document and any applicable legal

requirements, norms and standards concerning

customer's products and any use of the product of

Infineon Technologies in customer's applications.

The data contained in this document is exclusively

intended for technically trained staff. It is the

responsibility of customer's technical departments to

evaluate the suitability of the product for the intended

application and the completeness of the product

information given in this document with respect to

such application.

WARNINGS

Due to technical requirements products may contain

dangerous substances. For information on the types

in question please contact your nearest Infineon

Technologies office.

Do you have a question about any

aspect of this document?

Email: erratum@infineon.com

Except as otherwise explicitly approved by Infineon

Technologies in a written document signed by

authorized representatives of Infineon Technologies,

Infineon Technologies’ products may not be used in

any applications where a failure of the product or any

consequences of the use thereof can reasonably be

expected to result in personal injury.

TLE4959-5U-SP [INFINEON]

相关型号：

TLE4959C

TLE4959C-FX

TLE4961-1K

TLE4961-1M

TLE4961-2M

TLE4961-3L

TLE49611KXTSA1

TLE49611LHALA1

TLE49611MXTMA1

TLE49611MXTSA1

TLE49612MXTSA1

TLE49613LHALA1