TLF80511TF V50 [INFINEON]

TLF80511TF V50 是一款线性低压差稳压器，适用于具有固定输出电压（5V），负载电流高达 400 mA 的 D²PAK、DPAK 和 DSO8-EP 封装。高达 40V 的输入电压调节为 V Q，nom 为 5V，精度为±2％。TLF80511TF V50 的典型静态电流为38μA，对于需要极低工作电流的系统来说，它就是理想的解决方案，例如永久连接电池的系统。当输出电流小于 100mA 时，它具有 100mV 的极低压差。此外，压差区域始于输入电压为 3.3 V 时（扩展操作范围）。因此，TLF80511TF V50 适用于汽车系统。此外，TLF80511TF V50 的新型快速调节理念仅需一个 1μF 的输出电容即可保持电压稳定。;


型号：	TLF80511TF V50
厂家：	Infineon
描述：	TLF80511TF V50 是一款线性低压差稳压器，适用于具有固定输出电压（5V），负载电流高达 400 mA 的 D²PAK、DPAK 和 DSO8-EP 封装。高达 40V 的输入电压调节为 V Q，nom 为 5V，精度为±2％。TLF80511TF V50 的典型静态电流为38μA，对于需要极低工作电流的系统来说，它就是理想的解决方案，例如永久连接电池的系统。当输出电流小于 100mA 时，它具有 100mV 的极低压差。此外，压差区域始于输入电压为 3.3 V 时（扩展操作范围）。因此，TLF80511TF V50 适用于汽车系统。此外，TLF80511TF V50 的新型快速调节理念仅需一个 1μF 的输出电容即可保持电压稳定。电池稳压器
文件：	总20页 (文件大小：1754K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TLF80511TF

Low Dropout Linear Fixed Voltage Regulator

TLF80511TFV50

TLF80511TFV33

Data Sheet

Rev. 1.0, 2014-01-28

Automotive Power

TLF80511TF

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1

3.2

Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pin Assignment PG-TO252-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pin Definitions and Functions PG-TO252-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.1

4.2

4.3

Block Description and Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Voltage Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Typical Performance Characteristics Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Typical Performance Characteristics Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1

5.2

5.3

5.4

Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Selection of External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Input Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Output Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Thermal Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Reverse Polarity Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.1

6.2

6.2.1

6.2.2

6.3

6.4

6.5

Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Data Sheet

Rev. 1.0, 2014-01-28

Low Dropout Linear Fixed Voltage Regulator

TLF80511TF

Overview

Features

•

Output Voltage 5 V and 3.3 V

Output Voltage Precision ±2 %

Output Current up to 400 mA

Ultra Low Current Consumption 38 µA

Very Low Dropout Voltage: 100 mV at 100 mA Output Current

Extended Operating Range Starting at 3.3 V

Small Output Capacitor 1 µF

Output Current Limitation

Overtemperature Shutdown

Suitable for Use in Automotive Electronics

Wide Temperature Range from -40 °C up to 150 °C

Green Product (RoHS compliant)

AEC Qualified

PG-TO252-3

Description

The TLF80511TF is a linear low dropout voltage regulator for load currents up to 400 mA. An input voltage of up

to 40 V is regulated to V_Q,nom= 5 V (TLF80511TFV50) or V_Q,nom= 3.3 V (TLF80511TFV33) with ±2 % precision.

The TLF80511TF with a typical quiescent current of 38 µA, is the ideal solution for systems requiring very low

operating currents, such as those permanently connected to a battery.

It features a very low dropout voltage of 100 mV, when the output current is less than 100 mA. In addition, the

dropout region begins at input voltages of 3.3 V (extended operating range). This makes the TLF80511TF suitable

to supply automotive systems.

In addition, the TLF80511’s new fast regulation concept requires only a single, 1 µF output capacitor to maintain

stable regulation.

The device is designed for the harsh environment of automotive applications. Therefore standard features like

output current limitation and overtemperature shutdown are implemented and protect the device against failures

like output short circuit to GND, over-current and over-temperatures. The TLF80511TF can be also used in all

other applications requiring a stabilized 5 V or 3.3 V supply voltage.

Type

Package

Marking

80511V5

80511V3

TLF80511TFV50

TLF80511TFV33

PG-TO252-3

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Diagram

Current

Limitation

Bandgap

Reference

Temperature

Shutdown

GND

Figure 1

Block Diagram

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Pin Configuration

3.1

Pin Assignment PG-TO252-3

GND

Figure 2

Pin Configuration

3.2

Pin Definitions and Functions PG-TO252-3

Symbol

Function

Input

for compensating line influences, a capacitor to GND close to the IC terminals is

recommended

GND

Ground

Output

block to GND with a capacitor close to the IC terminals, respecting the values given

for its capacitance CQ and ESR in the table “Functional Range” on Page 7

Tab

GND

Heat Slug

connect to heatsink area;

connect with GND on PCB

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

General Product Characteristics

4.1

Absolute Maximum Ratings

Table 1

Absolute Maximum Ratings ¹⁾

T_j= -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin

(unless otherwise specified)

Parameter

Symbol

Values

Typ.

Unit Note /

Test Condition

Number

Min.

-0.3

Max.

Input I

Voltage

V_I

–

P_4.1.1

P_4.1.2

Output Q

Voltage

V_Q

–

Temperature

Junction Temperature

Storage Temperature

ESD Susceptibility

T_j

-40

-55

–

150

°C

–

P_4.1.3

P_4.1.4

T_stg

V_ESD

-4

–

HBM²⁾

CDM³⁾

P_4.1.5

P_4.1.6

-1.5

1.5

1) Not subject to production test, specified by design.

2) ESD susceptibility, HBM according to ANSI/ESDA/JEDEC JS001 (1.5k Ω, 100 pF)

3) ESD susceptibility, Charged Device Model “CDM” according JEDEC JESD22-C101

Note:Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

Note:Integrated protection functions are designed to prevent IC destruction under fault conditions described in the

data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are

not designed for continuous repetitive operation.

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

General Product Characteristics

4.2

Functional Range

Table 2

Functional Range

Parameter

Symbol

Values

Typ. Max.

Unit

Note /

Test Condition

Number

Min.

Input Voltage Range for Normal

Operation

V_I

_Q,nom+ V_dr

–

P_4.2.1

Extended Input Voltage Range

V_I,ext

3.3

–

T_j> 25 °C¹⁾

P_4.2.2

P_4.2.3

Output Capacitor’s Requirements C_Q

µF

–

for Stability

Output Capacitor’s Requirements ESR(C_Q)

for Stability

–

Ω

–

P_4.2.4

P_4.2.5

Junction Temperature

T_j

-40

150

°C

–

1) Between min. value and V_Q,nom+ V_dr: V_Q= V_I- V_dr. Below min. value: V_Q= 0 V

2) the minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30%

3) relevant ESR value at f = 10 kHz

Note:Within the functional range the IC operates as described in the circuit description. The electrical

characteristics are specified within the conditions given in the related electrical characteristics table.

4.3

Thermal Resistance

Note:This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, go

to www.jedec.org.

Table 3

Thermal Resistance

Parameter

Symbol

Values

Typ.

Unit

Note /

Test Condition

Number

Min.

Max.

Package Version PG-TO252-3

Junction to Case¹⁾

R_thJC

R_thJA

–

K/W

–

P_4.3.1

P_4.3.2

P_4.3.3

Junction to Ambient

footprint only³⁾

300 mm²heatsink P_4.3.4

area on PCB³⁾

Junction to Ambient

R_thJA

–

K/W

600 mm²heatsink P_4.3.5

area on PCB³⁾

1) Not subject to production test, specified by design

2) Specified R_thJAvalue is according to Jedec JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The Product

(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm³ board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu).

Where applicable a thermal via array under the exposed pad contacted the first inner copper layer.

3) Specified R_thJAvalue is according to JEDEC JESD 51-3 at natural convection on FR4 1s0p board; The Product

(Chip+Package) was simulated on a 76.2 × 114.3 × 1.5 mm³board with 1 copper layer (1 x 70µm Cu).

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

5.1

Voltage Regulation

The output voltage V_Qis divided by a resistor network. This fractional voltage is compared to an internal voltage

reference and drives the pass transistor accordingly.

The control loop stability depends on the output capacitor C_Q, the load current, the chip temperature and the

internal circuit design. To ensure stable operation, the output capacitor’s capacitance and its equivalent series

resistor ESR requirements given in Table 2 “Functional Range” on Page 7 must be maintained. For details see

the typical performance graph “Stability Region: Equivalent Serial Resistor ESR versus Output Current IQ”

on Page 11. Since the output capacitor is used to buffer load steps, it should be sized according to the

application’s needs.

An input capacitor C_Iis not required for stability, but is recommended to compensate line fluctuations. An

additional reverse polarity protection diode and a combination of several capacitors for filtering should be used.

Connect the capacitors close to the regulator terminals.

Whenever the load current exceeds the specified limit, e.g. in case of a short circuit, the output current is limited

and the output voltage decreases.

The overtemperature shutdown circuit prevents the IC from immediate destruction under fault conditions (e.g.

output continuously short-circuited) by switching off the power stage. After the chip has cooled, the regulator

restarts. This oscillatory thermal behaviour causes the junction temperature to exceed the 150° C maximum and

significantly reducing the IC’s life.

Regulated

Output Voltage

Supply

I_Q

I_I

Current

Limitation

LOAD

Bandgap

Reference

C_I

V_I

V_Q

ESR

C_Q

Temperature

Shutdown

GND

ApplicationDiagram.vsd

Figure 3

Block Diagram Voltage Regulation

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

Table 4

Electrical Characteristics Voltage Regulator 5 V and 3.3 V version

V_I= 13.5 V; T_j= -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin

(unless otherwise specified)

Parameter

Symbol

Values

Unit Note / Test Condition Number

Min. Typ. Max.

Output Voltage Precision

TLF80511TFV50

V_Q

4.9

5.0

5.1

0.05 mA < I_Q< 400 mA P_5.1.1

6 V < V_I< 28 V

Output Voltage Precision

TLF80511TFV50

V_Q

4.9

5.0

5.1

0.05 mA < I_Q< 200 mA P_5.1.2

5.5 V < V_I< 40 V

Output Voltage Precision

TLF80511TFV33

V_Q

3.23 3.3

3.37

0.05 mA < I_Q< 400 mA P_5.1.3

4.4 V < V_I< 28 V

Output Voltage Precision

TLF80511TFV33

V_Q

0.05 mA < I_Q< 200 mA P_5.1.4

3.9 V < V_I< 40 V

Output Current Limitation

I_Q,max

401

600

900

0 V < V_Q< 4.8 V

P_5.1.5

Load Regulation

steady-state

|∆VQ,load| –

I_Q= 0.05 mA to 400 mA P_5.1.6

V_I= 6 V

Line Regulation

steady-state

Dropout Voltage¹⁾

V_dr= V_I- V_Q

TLF80511TFV50

|∆VQ,line|

Vdr

–

V_I= 8 V to 32 V

I_Q= 5 mA

P_5.1.7

250

500

I_Q= 250 mA

I_Q= 100 mA

I_Q= 250 mA

I_Q= 100 mA

P_5.1.8

Dropout Voltage

V_dr= V_I- V_Q

TLF80511TFV50

Vdr

–

100

320

130

–

P_5.1.9

Dropout Voltage

V_dr= V_I- V_Q

TLF80511TFV33

650

–

P_5.1.10

P_5.1.11

Dropout Voltage

V_dr= V_I- V_Q

TLF80511TFV33

Power Supply Ripple Rejection²⁾PSRR

TLF80511TFV50

–

°C

_ripple= 100 Hz

P_5.1.12

P_5.1.13

P_5.1.14

V_ripple= 0.5 Vpp

Overtemperature Shutdown

Threshold

T_j,sd

151

–

175

200

–

T_jincreasing²⁾

T_jdecreasing²⁾

Overtemperature Shutdown

Threshold Hysteresis

T_j,sdh

1) Measured when the output voltage V_Qhas dropped 100 mV from the nominal value obtained at V_I= 13.5V

2) Not subject to production test, specified by design

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

5.2

Typical Performance Characteristics Voltage Regulator

Typical Performance Characteristics

Output Voltage V_Qversus

Dropout Voltage V_drversus

Junction Temperature T_j(TLF80511TFV50)

5,20

400

V_I= 13.5 V

I_Q= 200 mA

5,15

5,10

5,05

5,00

4,95

4,90

4,85

4,80

350

_Q= 250 mA

300

250

200

150

100

_Q= 100 mA

_Q= 10 mA

-40

120

160

-40

120

160

_j[°C]

Dropout Voltage V_drversus

Output Current I_Q(TLF80511TFV50)

Maximum Output Current I_Qversus

Input Voltage V_I(TLF80511TFV50)

600

700

V_Q= 4.8 V

600

500

400

300

200

100

500

_j= 125 °C

T_j= 150 °C

T_j= 25 °C

T_j= -40 °C

400

300

200

100

_j= 25 °C

100

200

300

400

I_Q[mA]

_I[V]

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

Load Regulation ΔV_Q,loadversus

Output Current Change ΔI_Q

Line Regulation ΔV_Q,lineversus

Input Voltage ∆V_I

I_Q= 5 mA

V_I= 13.5 V

T_j= 25 °C

-2

T_j= -40 °C

T_j= 150 °C

T_j= 25 °C

-4

-6

T_j= -40 °C

-2

-8

-4

-6

-8

-10

-12

100

200

300

400

ΔI_Q[mA]

ΔV_I[V]

Power Supply Ripple Rejection versus

Frequency (TLF80511TFV50)

Stability Region: Equivalent Serial Resistor ESR

versus Output Current I_Q

100

_Q= 1 µF

_Q= 10 mA

_Q= 1 µF

V_I= 6..28 V

_I= 13.5 V

V_ripple= 0.5 Vpp

Unstable

Region

T_j= 25 °C

Stable

Region

0,1

0,01

100

200

300

400

0,01

0,1

100

1000

[kHz]

I_Q[mA]

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

Output Voltage V_Qversus

Input Voltage V_I(TLF80511TFV50)

_Q= 100 mA

T_j= 25°C

_I[V]

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

5.3

Current Consumption

Table 5

Electrical Characteristics Current Consumption

V_I= 13.5 V; T_j= -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin

(unless otherwise specified)

Parameter

Symbol

Values

Typ.

Unit

Note / Test Condition Number

Min.

Max.

Current Consumption

I_q= I_I- I_Q

I_q

–

µA

I_Q= 0.05 mA

T_j< 25 °C

P_5.3.1

P_5.3.2

P_5.3.3

Current Consumption

I_q= I_I- I_Q

–

I_Q= 0.05 mA

T_j< 125 °C

Current Consumption

I_q= I_I- I_Q

I_Q= 400 mA

T_j< 125 °C¹⁾

1) Not subject to production test, specified by design.

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Block Description and Electrical Characteristics

5.4

Typical Performance Characteristics Current Consumption

Typical Performance Characteristics

Current Consumption I_qversus

Output Current I_Q

Current Consumption I_qversus

Input Voltage V_I

100

V_I= 13.5 V

R_LOAD= 100 Ω

T_j= 25 °C

_j= 150 °C

T_j= 25 °C

_j= -40 °C

100

200

300

400

_I[V]

I_Q[mA]

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Application Information

6.1

Application Diagram

Supply

Regulated Output Voltage

Load

e. g.

D_I1

Micro

Controller

Current

Limitation

XC22xx

C_Q

D_I2

C_I2

C_I1

1µF

(ESR<5ꢀ)

100nF

<45V

10µF

Bandgap

Reference

GND

Temperature

Shutdown

GND

Figure 4

Application Diagram

6.2

Selection of External Components

6.2.1

Input Pin

The typical input circuitry for a linear voltage regulator is shown in the application diagram above.

A ceramic capacitor at the input, in the range of 100nF to 470nF, is recommended to filter out the high frequency

disturbances imposed by the line e.g. ISO pulses 3a/b. This capacitor must be placed very close to the input pin

of the linear voltage regulator on the PCB.

An aluminum electrolytic capacitor in the range of 10µF to 470µF is recommended as an input buffer to smooth

out high energy pulses, such as ISO pulse 2a. This capacitor should be placed close to the input pin of the linear

voltage regulator on the PCB.

An overvoltage suppressor diode can be used to further suppress any high voltage beyond the maximum rating

of the linear voltage regulator and protect the device against any damage due to over-voltage above 45 V.

The external components at the input are not mandatory for the operation of the voltage regulator, but they are

recommended in order to protect the voltage regulator against external disturbances and damages.

6.2.2

Output Pin

An output capacitor is mandatory for the stability of linear voltage regulators.

The requirement to the output capacitor is given in “Functional Range” on Page 7. The graph “Stability Region:

Equivalent Serial Resistor ESR versus Output Current IQ” on Page 11 shows the stable operation range of

the device.

TLF80511TF is designed to be stable with extremely low ESR capacitors. According to the automotive

requirements, ceramic capacitors with X5R or X7R dielectrics are recommended.

The output capacitor should be placed as close as possible to the regulator’s output and GND pins and on the

same side of the PCB as the regulator itself.

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Application Information

In case of rapid transients of input voltage or load current, the capacitance should be dimensioned in accordance

and verified in the real application that the output stability requirements are fulfilled.

6.3

Thermal Considerations

Knowing the input voltage, the output voltage and the load profile of the application, the total power dissipation

can be calculated:

P_D= (V_I- V_Q) × I_Q+ V_I× I_q

(1)

with

•

P_D: continuous power dissipation

V_I: input voltage

V_Q: output voltage

I_Q: output current

I_q: quiescent current

The maximum acceptable thermal resistance R_thJAcan then be calculated:

R_thJA,max= ( T_j,max- T_a) / P_D

(2)

with

•

_j,max: maximum allowed junction temperature

T_a: ambient temperature

Based on the above calculation the proper PCB type and the necessary heat sink area can be determined with

reference to the specification in “Thermal Resistance” on Page 7.

Example

Application conditions:

V_I= 13.5V

V_Q= 5V

I_Q= 150mA

T_a= 85°C

Calculation of R_thJA,max

P_D= (V_I– V_Q) × I_Q+ V_I× I_q

= (13.5V – 5V) × 150mA

= 1.275W

(V_I× I_qcan be neglected because of very low I_q)

R_thJA,max= (T_j,max– T_a) / P_D

= (150°C – 85°C) / 1.275W = 50.98K/W

As a result, the PCB design must ensure a thermal resistance R_thJAlower than 50.98 K/W. According to “Thermal

Resistance” on Page 7, at least 600 mm²heatsink area is needed on the FR4 1s0p PCB, or the FR4 2s2p board

can be used.

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Application Information

6.4

Reverse Polarity Protection

TLF80511TF is not self protected against reverse polarity faults and must be protected by external components

against negative supply voltage. An external reverse polarity diode is needed. The absolute maximum ratings of

the device as specified in “Absolute Maximum Ratings” on Page 6 must be kept.

6.5

Further Application Information

•

For further information you may contact http://www.infineon.com/

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Package Outlines

+0.15

6.5

5.4

-0.05

+0.05

-0.10

2.3

±0.1

+0.08

(5)

0.5

-0.04

+0.20

-0.01

0.9

0...0.15

0.15 MAX.

per side

0.75

+0.08

-0.04

0.5

±0.1

2.28

0.1 B

4.57

0.25

A B

All metal surfaces tin plated,

except area of cut.

GPT09277

Figure 5

PG-TO252-3

Data Sheet

Rev. 1.0, 2014-01-28

TLF80511TF

Revision History

Revision

Date

Changes

1.0

2014-01-28

Data Sheet - Initial version

Data Sheet

Rev. 1.0, 2014-01-28

Edition 2014-01-28

Published by

Infineon Technologies AG

81726 Munich, Germany

Legal Disclaimer

The information given in this document shall in no event be regarded as a guarantee of conditions or

characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any

information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties

and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights

of any third party.

Information

For further information on technology, delivery terms and conditions and prices, please contact the nearest

Infineon Technologies Office (www.infineon.com).

Warnings

Due to technical requirements, components may contain dangerous substances. For information on the types in

question, please contact the nearest Infineon Technologies Office.

Infineon Technologies components may be used in life-support devices or systems only with the express written

approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure

of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support

devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain

and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may

be endangered.

TLF80511TF V50 [INFINEON]

相关型号：

TLF80511TFV33

TLF80511TFV50

TLF9CB1020R8

TLF9CB102R54

TLF9CB102W0R8

TLF9CB102WR54

TLF9CB103R54

TLF9CB103W0R8

TLF9CB103WR54

TLF9CBH1020R8

TLF9CBH102R54

TLF9CBH102W0R8