CGS702V [INTEL]
Clock Generator,;型号: | CGS702V |
厂家: | INTEL |
描述: | Clock Generator, |
文件: | 总5页 (文件大小:441K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SUPPORT COMPONENTS
NATIONAL SEMICONDUCTOR
CGS253x Quad 1 to 4 Clock Drivers
■
■
■
■
Pin-to-Pin Skew of Less Than
350 ps
Part-to-Part Skew of Less Than
650 ps
Output Series Resistor Integrated
Into CGS2537
Supports TTL and CMOS Output
Clock Rates to 125 MHz
Accepts TTL and CMOS Inputs
Maximum Propagation Delays of 3.5
to 4.5 ns
■
■
■
Greater Than 125 MHz Maximum
Frequency
■
■
5V/3.3V Options
1X and 0.5X Output Capability
National Semiconductor’s Clock
Generation and Support (CGS*) family
offers you a complete portfolio of clock
generation and distribution timing solu-
tions. The newest family of high perfor-
mance clock drivers offers you the highest
performance and flexibility available in a
cost-effective device – High speed as
measured by maximum frequency, accura-
cy as measured by skew, and flexibility as
measured by supply voltages and output
configurations. National’s clock drivers
save time and effort by offering synchro-
nous signals that reduce timing errors and
system failures. These clock drivers also
integrate output series resistors that reduce
undershoot and simplify line termination
design. They further aid designers by
offering high fanout that reduces compo-
nent count and saves board real estate. In
addition, for today’s mixed voltage sys-
tems, the inputs are 5V tolerant when
using a 3.3V supply. National’s CGS253x
family of clock drivers (CGS2534V/
CGS2535V/CGS2536V/CGS2537V) is
optimized to drive large loads with sub-
3.5ns propagation delays, 1.5ns edge rates,
and 36mA drive.
located. In addition, one can access the
models at URL: http://www/vhdl.org/
pub/ibis (and click on ‘models’and
‘national’) or using a modem to dial up
(415) 335-0110. IBIS (I/O Buffer
Information Specification) is a fast and
accurate behavioral method of modeling
I/O buffers based on V/I curve data
derived from measurements or full circuit
simulation. IBIS uses a standardized soft-
ware parsable format to create the behav-
ioral information needed to model analog
characteristics of ICs and can be used by
almost any analog simulator/EDA tool in
the industry. IBIS is developed by the
IBIS Open Forum and most forum activi-
ties are handled through email discus-
sions using the reflector ibis@vhdl.org.
P R O C E S S O R S S U P P O RT E D :
80186, 80C186, 80C186XL/EA/EB/EC,
80L186EA/EB/EC, 80188,
80C188, 80C188XL/EA/EB/EC,
80L188EA/EB/EC, Intel386™
CX/EX/SX/SXSA/DX, and Intel486™
SX, IntelDX2™ , IntelDX4™ Processors
AVA I L A B I L I T Y:
Now
C O N TA C T:
National Semiconductor
Phone: (800) 272-9959
For international contacts see Appendix B.
IBIS models for the CGS253x, along with
all of National’s clock generators and dri-
vers, can be downloaded (via FTP) from
the Internet at vhdl.org, where all of the
semiconductor industry’s IBIS models are
200
SUPPORT COMPONENTS
NATIONAL SEMICONDUCTOR
CGS70x Low Skew Clock Generators
■
Up to 9 CMOS Clock Outputs
25-160 MHz Output Frequency
Range
■
■
■
Less Than 400 ps Pin-to-Pin Skew
Supports Clock Doubling and
Quadrupling
■
Internal Phase Locked Loop (PLL)
With VCO Operating Greater Than
160 MHz
■
■
■
■
CGS702 Has Reduced EMI
Sub-300 ps Long Term Jitter
30mA Drive
PLCC Packaging For Optimum
Skew Performance
National Semiconductor’s Clock
Generation and Support (CGS*) family
offers a complete portfolio of clock gener-
ation and distribution timing solutions for
all embedded Intel Architecture micro-
processors. National’s newest family of
high performance clock generators offers
high performance and flexibility in a cost-
effective device. The CGS700V/701V/
702V have on-chip PLLs that are used to
generate 25-160 MHz outputs from 25-
40 MHz inputs. The CGS701 has external
feedback for output edge placement
control.
P R O C E S S O R S S U P P O RT E D :
80186, 80C186, 80C186XL/EA/EB/EC,
80L186EA/EB/EC, 80188,
80C188, 80C188XL/EA/EB/EC,
80L188EA/EB/EC, Intel386™
CX/EX/SX/SXSA/DX, and Intel486™
SX, IntelDX2™ , IntelDX4™ Processors
the IBIS Open Forum and most forum
activities are handled through e-mail dis-
cussions using the reflector
ibis@vhdl.org.
IBIS models for the CGS70x, along with
all of National’s clock generators and dri-
vers, can be downloaded (via FTP) from
the Internet at vhdl.org, where all of the
semiconductor industry’s IBIS models are
located. In addition, one can access the
models at URL: http://www/vhdl.org/
pub/ibis (and click on ‘models’and
AVA I L A B I L I T Y:
Now
C O N TA C T:
National Semiconductor
Phone: (800) 272-9959
For international contacts see Appendix B.
‘national’) or using a modem to dial up
(415) 335-0110. IBIS (I/O Buffer
Information Specification) is a fast and
accurate behavioral method of modeling
I/O buffers based on V/I curve data
derived from measurements or full circuit
simulation. IBIS uses a standardized
software parsable format to create the
behavioral information needed to model
analog characteristics of ICs and can be
used by almost any analog simulator/EDA
tool in the industry. IBIS is developed by
201
SUPPORT COMPONENTS
NATIONAL SEMICONDUCTOR
DP843x Programmable DRAM Controllers
■
Supports Nibble, Page, and Static
Column DRAMs
■
■
■
33 MHz Operation
Dual Access Ports (DP8432 only)
Addresses Up to 64MB DRAM
Arrays
■
■
Supports Up to 4MB DRAMs
4 RAS and 4 CAS Drivers
The DP8430V/31V/32V DRAM con-
trollers provide a low cost, single chip
interface between DRAM and all embed-
ded Intel Architecture microprocessors.
The DP8430V/31V/32V generate all the
required access control signal timing for
DRAMs and an on-chip refresh request
clock is used to automatically refresh the
DRAM array. Refreshes and accesses are
arbitrated on chip. If necessary, a WAIT
or DTACK output inserts wait states into
system access cycles, including burst
mode accesses. RAS low time during
refreshes and RAS precharge time after
refreshes and back to back accesses are
guaranteed through the insertion of wait
states. Separate on-chip precharge coun-
ters for each RAS output can be used for
memory interleaving to avoid delayed
back to back accesses because of
DP8430/31/32 BLOCK DIAGRAM
P R O C E S S O R S S U P P O RT E D :
80186, 80C186, 80C186XL/EA/EB/EC,
80L186EA/EB/EC, 80188,
80C188, 80C188XL/EA/EB/EC,
80L188EA/EB/EC, Intel386™
CX/EX/SX/SXSA/DX, and
Intel486™ SX, IntelDX2™ , IntelDX4™
Processors
precharge. An additional feature of the
DP8432V is two access ports to simplify
dual accessing. Arbitration among these
ports and refresh is done on chip.
AVA I L A B I L I T Y:
Now
The DP8430V and DP8431V are available
in a 68-pin PLCC package while the
DP8432V is available in an 84-pin PLCC
package. All are available in 33 MHz
speeds.
C O N TA C T:
National Semiconductor
Phone: (800) 272-9959
For international contacts see Appendix B.
202
SUPPORT COMPONENTS
NATIONAL SEMICONDUCTOR
DP844x Programmable DRAM Controllers
■
■
■
■
■
25 MHz and 40 MHz Operation
Supports Up to 64-Bit Bus Widths
Addresses Up to 1/2 GB of Memory
Supports Up to 64MB DRAMs
Supports Fast Page, Nibble, and
Static Column DRAMs
■
■
■
■
Page Detection
Automatic CPU Burst Accesses
Automatic Internal Refresh
Burst and RAS-Before-CAS Refresh
National Semiconductor’s DP8440 and
DP8441 DRAM Controllers provide an
easy interface between DRAM arrays and
embedded Intel Architecture microproces-
sors. These DRAM Controllers generate
all necessary control and timing signals to
successfully interface and design dynamic
memory systems and support page and
burst accesses for fast page, static column,
and nibble DRAMs.
The DP8440 supports DRAMs as large as
16MB with a maximum addressable space
of 256MB while the DP8441 can support
64MB DRAMs with a maximum address-
able space of 1/2 GB. Both devices sup-
port microprocessor bus widths of up to
32-bits while the DP8441 supports 64-bit
bus widths as well.
P R O C E S S O R S S U P P O RT E D :
80186, 80C186,
80C186XL/EA/EB/EC,
80L186EA/EB/EC, 80188, 80C188,
80C188XL/EA/EB/EC,
80L188EA/EB/EC, Intel386™
CX/EX/SX/SXSA/DX, and Intel486™
SX,
Programmable features make the
DP8440/41 flexible enough to fit many
memory systems. These controllers
include page comparators, burst mode
support, and CAS-before-RAS refresh
features. Burst length is programmable on
both chips. They also include on-chip
Phase-Locked Loops (PLLs) which pro-
vide a high-precision delay line that gen-
erates sub-clock cycle delays to improve
system performance. Because the CMOS
circuits support high-capacitance drive
capabilities, system designers are not
required to add memory buffers.
IntelDX2™ , IntelDX4™ Processors
AVA I L A B I L I T Y:
Now
C O N TA C T:
National Semiconductor
Phone: (800) 272-9959
For international contacts see Appendix B.
Both devices are available in 25 MHz and
40 MHz versions and are packaged in a
100-pin PQFP package. Additionally, the
DP8440 is also available in a 84-pin
PLCC package (40 MHz version only).
203
SUPPORT COMPONENTS
VADEM
Intel Architecture and ISA Compatible Solutions
PCMCIA Host Adapters
H O S T S Y S T E M S S U P P O RT E D :
The VG660, is an industry standard LCD
■
■
■
■
VG365
N/A
VGA controller specifically designed to
support small flat panels with enhanced
features and VGA compatibility at the
same time. Using the highly integrated
VG660, designers can create an entire
VGA LCD subsystem in less than 3
square inches. The device supports a
variety of memory display types
including DRAMS, PSRAMS, and
SRAMS. Built-in power management
capabilities support sleep, suspend and
standby modes.
– Dual Socket PC Card Controller
VG465
– Single Socket PC Card Controller
VG468
– Single Socket PC Card Controller
VG469
– Dual Socket Mixed Voltage PC
Card Controller
P R O C E S S O R S S U P P O RT E D :
Intel386™ CX/EX/SX/SXSA/DX,
and Intel486™ SX, IntelDX2™ , and
IntelDX4 Processors
AVA I L A B I L I T Y:
Immediately available and in volume
production.
C O N TA C T:
VGA LCD/CRT Controller
■
Vadem
1960 Zanker Road
San Jose, CA 95112
Phone: (408) 467-2100
FAX: (408) 467-2199
For international contacts see Appendix B.
VG660
– 100 Pin Low Cost VGA LCD/CRT
Controller
Vadem’s PCMCIA Host Adapters, VG465,
VG365, VG468 and VG469 offer full
compatibility with Intel’s ExCA and
PCMCIA, and are Intel “B” step register
set and software compatible. Vadem’s
PCMCIA controllers offer OEMs an easy
and safe upgrade path to mixed voltage
systems and plug-and-play standards.
They also are designed to help end-users
easily use the standard. Applications
include desktop docking systems for
portables, conventional desktops, informa-
tion appliances, subnotebook computers
and portable peripherals.
204
相关型号:
©2020 ICPDF网 联系我们和版权申明