EPM7128BFC256-4N [INTEL]
EE PLD, 4ns, 128-Cell, CMOS, PBGA256, FBGA-256;型号: | EPM7128BFC256-4N |
厂家: | INTEL |
描述: | EE PLD, 4ns, 128-Cell, CMOS, PBGA256, FBGA-256 时钟 LTE 输入元件 可编程逻辑 |
文件: | 总76页 (文件大小:1516K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MAX 7000B
Programmable Logic
Device
®
September 2005, ver. 3.5
Data Sheet
■
High-performance 2.5-V CMOS EEPROM-based programmable logic
devices (PLDs) built on second-generation Multiple Array MatriX
(MAX®) architecture (see Table 1)
Features...
–
Pin-compatible with the popular 5.0-V MAX 7000S and 3.3-V
MAX 7000A device families
–
–
High-density PLDs ranging from 600 to 10,000 usable gates
3.5-ns pin-to-pin logic delays with counter frequencies in excess
of 303.0 MHz
■
Advanced 2.5-V in-system programmability (ISP)
–
Programs through the built-in IEEE Std. 1149.1 Joint Test Action
Group (JTAG) interface with advanced pin-locking capability
Enhanced ISP algorithm for faster programming
ISP_Done bit to ensure complete programming
Pull-up resistor on I/O pins during in-system programming
ISP circuitry compliant with IEEE Std. 1532
–
–
–
–
For information on in-system programmable 5.0-V MAX 7000S or 3.3-V
MAX 7000A devices, see the MAX 7000 Programmable Logic Device Family
Data Sheet or the MAX 7000A Programmable Logic Device Family Data Sheet.
f
Table 1. MAX 7000B Device Features
Feature
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
Usable gates
Macrocells
600
32
2
1,250
64
2,500
128
8
5,000
256
16
10,000
512
Logic array blocks
4
32
Maximum user I/O
pins
36
68
100
164
212
t
PD (ns)
SU (ns)
3.5
2.1
3.5
2.1
4.0
2.5
5.0
3.3
5.5
3.6
t
tFSU (ns)
CO1 (ns)
1.0
1.0
1.0
1.0
1.0
t
2.4
2.4
2.8
3.3
3.7
fCNT (MHz)
303.0
303.0
243.9
188.7
163.9
Altera Corporation
1
DS-MAX7000B-3.5
MAX 7000B Programmable Logic Device Data Sheet
■
System-level features
–
...and More
Features
MultiVoltTM I/O interface enabling device core to run at 2.5 V,
while I/O pins are compatible with 3.3-V, 2.5-V, and 1.8-V logic
levels
–
–
–
Programmable power-saving mode for 50% or greater power
reduction in each macrocell
Fast input setup times provided by a dedicated path from I/O
pin to macrocell registers
Support for advanced I/O standards, including SSTL-2 and
SSTL-3, and GTL+
–
–
–
Bus-hold option on I/O pins
PCI compatible
Bus-friendly architecture including programmable slew-rate
control
–
–
–
Open-drain output option
Programmable security bit for protection of proprietary designs
Built-in boundary-scan test circuitry compliant with
IEEE Std. 1149.1
–
–
Supports hot-socketing operation
Programmable ground pins
■
Advanced architecture features
–
–
–
Programmable interconnect array (PIA) continuous routing
structure for fast, predictable performance
Configurable expander product-term distribution, allowing up
to 32 product terms per macrocell
Programmable macrocell registers with individual clear, preset,
clock, and clock enable controls
–
–
–
Two global clock signals with optional inversion
Programmable power-up states for macrocell registers
6 to 10 pin- or logic-driven output enable signals
■
Advanced package options
–
Pin counts ranging from 44 to 256 in a variety of thin quad flat
pack (TQFP), plastic quad flat pack (PQFP), ball-grid array
(BGA), space-saving FineLine BGATM, 0.8-mm Ultra
FineLine BGA, and plastic J-lead chip carrier (PLCC) packages
Pin-compatibility with other MAX 7000B devices in the same
package
–
■
Advanced software support
–
Software design support and automatic place-and-route
provided by Altera’s MAX+PLUS® II development system for
Windows-based PCs and Sun SPARCstation, and HP 9000
Series 700/800 workstations
2
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
–
–
Additional design entry and simulation support provided by
EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized
modules (LPMs), Verilog HDL, VHDL, and other interfaces to
popular EDA tools from manufacturers such as Cadence,
Exemplar Logic, Mentor Graphics, OrCAD, Synopsys,
Synplicity, and VeriBest
Programming support with Altera’s Master Programming Unit
(MPU), MasterBlasterTM serial/universal serial bus (USB)
communications cable, and ByteBlasterMVTM parallel port
download cable, as well as programming hardware from third-
party manufacturers and any JamTM STAPL File (.jam), Jam Byte-
Code File (.jbc), or Serial Vector Format File (.svf)-capable in-
circuit tester
MAX 7000B devices are high-density, high-performance devices based on
Altera’s second-generation MAX architecture. Fabricated with advanced
CMOS technology, the EEPROM-based MAX 7000B devices operate with
a 2.5-V supply voltage and provide 600 to 10,000 usable gates, ISP,
pin-to-pin delays as fast as 3.5 ns, and counter speeds up to 303.0 MHz.
See Table 2.
General
Description
Table 2. MAX 7000B Speed Grades
Note (1)
Speed Grade
Device
-3
-4
-5
-7
-10
EPM7032B
v
v
v
v
v
v
v
v
EPM7064B
v
EPM7128B
EPM7256B
EPM7512B
v
v
v
v
v
v
Notes:
(1) Contact Altera Marketing for up-to-date information on available device speed
grades.
The MAX 7000B architecture supports 100% TTL emulation and high-
density integration of SSI, MSI, and LSI logic functions. It easily integrates
multiple devices ranging from PALs, GALs, and 22V10s to MACH and
pLSI devices. MAX 7000B devices are available in a wide range of
packages, including PLCC, BGA, FineLine BGA, 0.8-mm Ultra FineLine
BGA, PQFP, TQFP, and TQFP packages. See Table 3.
Altera Corporation
3
MAX 7000B Programmable Logic Device Data Sheet
Table 3. MAX 7000B Maximum User I/O Pins
Note (1)
Device
44-Pin 44-Pin 48-Pin 49-Pin
PLCC TQFP TQFP 0.8-mm
100-
Pin
TQFP
100-Pin
FineLine
BGA (4)
144- 169-Pin 208-
256- 256-Pin
Pin FineLine
BGA BGA (4)
Pin
TQFP
0.8-mm
Ultra
Pin
PQFP
(2)
Ultra
FineLine
BGA (3)
FineLine
BGA (3)
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
36
36
36
36
36
40
36
41
41
68
84
84
68
84
100
120
120
100
141
141
100
164
164
176
212
212
Notes:
(1) When the IEEE Std. 1149.1 (JTAG) interface is used for in-system programming or boundary-scan testing, four I/O
pins become JTAG pins.
(2) Contact Altera for up-to-date information on available device package options.
(3) All 0.8-mm Ultra FineLine BGA packages are footprint-compatible via the SameFrameTM pin-out feature. Therefore,
designers can design a board to support a variety of devices, providing a flexible migration path across densities
and pin counts. Device migration is fully supported by Altera development tools. See “SameFrame Pin-Outs” on
page 14 for more details.
(4) All FineLine BGA packages are footprint-compatible via the SameFrame pin-out feature. Therefore, designers can
design a board to support a variety of devices, providing a flexible migration path across densities and pin counts.
Device migration is fully supported by Altera development tools. See “SameFrame Pin-Outs” on page 14 for more
details.
MAX 7000B devices use CMOS EEPROM cells to implement logic
functions. The user-configurable MAX 7000B architecture accommodates
a variety of independent combinatorial and sequential logic functions.
The devices can be reprogrammed for quick and efficient iterations
during design development and debug cycles, and can be programmed
and erased up to 100 times.
MAX 7000B devices contain 32 to 512 macrocells that are combined into
groups of 16 macrocells, called logic array blocks (LABs). Each macrocell
has a programmable-AND/fixed-ORarray and a configurable register with
independently programmable clock, clock enable, clear, and preset
functions. To build complex logic functions, each macrocell can be
supplemented with both shareable expander product terms and high-
speed parallel expander product terms to provide up to 32 product terms
per macrocell.
4
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices provide programmable speed/power optimization.
Speed-critical portions of a design can run at high speed/full power,
while the remaining portions run at reduced speed/low power. This
speed/power optimization feature enables the designer to configure one
or more macrocells to operate up to 50% lower power while adding only
a nominal timing delay. MAX 7000B devices also provide an option that
reduces the slew rate of the output buffers, minimizing noise transients
when non-speed-critical signals are switching. The output drivers of all
MAX 7000B devices can be set for 3.3 V, 2.5 V, or 1.8 V and all input pins
are 3.3-V, 2.5-V, and 1.8-V tolerant, allowing MAX 7000B devices to be
used in mixed-voltage systems.
MAX 7000B devices are supported by Altera development systems, which
are integrated packages that offer schematic, text—including VHDL,
Verilog HDL, and the Altera Hardware Description Language (AHDL)—
and waveform design entry, compilation and logic synthesis, simulation
and timing analysis, and device programming. Altera software provides
EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for
additional design entry and simulation support from other industry-
standard PC- and UNIX-workstation-based EDA tools. Altera software
runs on Windows-based PCs, as well as Sun SPARCstation, and HP 9000
Series 700/800 workstations.
For more information on development tools, see the MAX+PLUS II
Programmable Logic Development System & Software Data Sheet and the
Quartus Programmable Logic Development System & Software Data Sheet.
f
The MAX 7000B architecture includes the following elements:
Functional
Description
■
■
■
■
■
LABs
Macrocells
Expander product terms (shareable and parallel)
PIA
I/O control blocks
The MAX 7000B architecture includes four dedicated inputs that can be
used as general-purpose inputs or as high-speed, global control signals
(clock, clear, and two output enable signals) for each macrocell and I/O
pin. Figure 1 shows the architecture of MAX 7000B devices.
Altera Corporation
5
MAX 7000B Programmable Logic Device Data Sheet
Figure 1. MAX 7000B Device Block Diagram
INPUT/GCLK1
INPUT/OE2/GCLK2
INPUT/OE1
INPUT/GCLRn
6 or 10 Output Enables (1)
6 or 10 Output Enables (1)
LAB A
LAB B
2 to 16
2 to 16
2 to 16
2 to 16
36
36
Macrocells
1 to 16
Macrocells
17 to 32
I/O
I/O
2 to 16 I/O
Control
Block
Control
Block
2 to 16 I/O
16
16
6 or 10
2 to 16
2 to 16
6 or 10
LAB C
LAB D
2 to 16
2 to 16
PIA
2 to 16
2 to 16
36
36
Macrocells
33 to 48
Macrocells
49 to 64
I/O
Control
Block
I/O
Control
Block
2 to 16 I/O
2 to 16 I/O
16
16
6 or 10
6 or 10
2 to 16
2 to 16
Note:
(1) EPM7032B, EPM7064B, EPM7128B, and EPM7256B devices have six output enables. EPM7512B devices have ten
output enables.
Logic Array Blocks
The MAX 7000B device architecture is based on the linking of
high-performance LABs. LABs consist of 16 macrocell arrays, as shown in
Figure 1. Multiple LABs are linked together via the PIA, a global bus that
is fed by all dedicated input pins, I/O pins, and macrocells.
Each LAB is fed by the following signals:
■
■
■
36 signals from the PIA that are used for general logic inputs
Global controls that are used for secondary register functions
Direct input paths from I/O pins to the registers that are used for fast
setup times
6
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Macrocells
The MAX 7000B macrocell can be individually configured for either
sequential or combinatorial logic operation. The macrocell consists of
three functional blocks: the logic array, the product-term select matrix,
and the programmable register. Figure 2 shows the MAX 7000B
macrocell.
Figure 2. MAX 7000B Macrocell
Global Global
LAB Local Array
Clear
Clocks
From
2
I/O pin
Parallel Logic
Expanders
(from other
macrocells)
Fast Input
Select
Programmable
Register
Register
Bypass
To I/O
Control
Block
PRN
D/T
Q
Clock/
Enable
Select
Product-
Term
Select
Matrix
ENA
CLRN
VCC
Clear
Select
To PIA
Shared Logic
Expanders
36 Signals
from PIA
16 Expander
Product Terms
Combinatorial logic is implemented in the logic array, which provides
five product terms per macrocell. The product-term select matrix allocates
these product terms for use as either primary logic inputs (to the ORand
XORgates) to implement combinatorial functions, or as secondary inputs
to the macrocell’s register preset, clock, and clock enable control
functions.
Two kinds of expander product terms (“expanders”) are available to
supplement macrocell logic resources:
■
■
Shareable expanders, which are inverted product terms that are fed
back into the logic array
Parallel expanders, which are product terms borrowed from adjacent
macrocells
Altera Corporation
7
MAX 7000B Programmable Logic Device Data Sheet
The Altera development system automatically optimizes product-term
allocation according to the logic requirements of the design.
For registered functions, each macrocell flipflop can be individually
programmed to implement D, T, JK, or SR operation with programmable
clock control. The flipflop can be bypassed for combinatorial operation.
During design entry, the designer specifies the desired flipflop type; the
MAX+PLUS II software then selects the most efficient flipflop operation
for each registered function to optimize resource utilization.
Each programmable register can be clocked in three different modes:
■
■
Global clock signal. This mode achieves the fastest clock-to-output
performance.
Global clock signal enabled by an active-high clock enable. A clock
enable is generated by a product term. This mode provides an enable
on each flipflop while still achieving the fast clock-to-output
performance of the global clock.
■
Array clock implemented with a product term. In this mode, the
flipflop can be clocked by signals from buried macrocells or I/O pins.
Two global clock signals are available in MAX 7000B devices. As shown
in Figure 1, these global clock signals can be the true or the complement of
either of the global clock pins, GCLK1or GCLK2.
Each register also supports asynchronous preset and clear functions. As
shown in Figure 2, the product-term select matrix allocates product terms
to control these operations. Although the product-term-driven preset and
clear from the register are active high, active-low control can be obtained
by inverting the signal within the logic array. In addition, each register
clear function can be individually driven by the active-low dedicated
global clear pin (GCLRn). Upon power-up, each register in a MAX 7000B
device may be set to either a high or low state. This power-up state is
specified at design entry.
All MAX 7000B I/O pins have a fast input path to a macrocell register.
This dedicated path allows a signal to bypass the PIA and combinatorial
logic and be clocked to an input D flipflop with an extremely fast input
setup time. The input path from the I/O pin to the register has a
programmable delay element that can be selected to either guarantee zero
hold time or to get the fastest possible set-up time (as fast as 1.0 ns).
8
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Expander Product Terms
Although most logic functions can be implemented with the five product
terms available in each macrocell, more complex logic functions require
additional product terms. Another macrocell can be used to supply the
required logic resources. However, the MAX 7000B architecture also
offers both shareable and parallel expander product terms (“expanders”)
that provide additional product terms directly to any macrocell in the
same LAB. These expanders help ensure that logic is synthesized with the
fewest possible logic resources to obtain the fastest possible speed.
Shareable Expanders
Each LAB has 16 shareable expanders that can be viewed as a pool of
uncommitted single product terms (one from each macrocell) with
inverted outputs that feed back into the logic array. Each shareable
expander can be used and shared by any or all macrocells in the LAB to
build complex logic functions. A small delay (tSEXP) is incurred when
shareable expanders are used. Figure 3 shows how shareable expanders
can feed multiple macrocells.
Figure 3. MAX 7000B Shareable Expanders
Shareable expanders can be shared by any or all macrocells in an LAB.
Macrocell
Product-Term
Logic
Product-Term Select Matrix
Macrocell
Product-Term
Logic
36 Signals
from PIA
16 Shared
Expanders
Altera Corporation
9
MAX 7000B Programmable Logic Device Data Sheet
Parallel Expanders
Parallel expanders are unused product terms that can be allocated to a
neighboring macrocell to implement fast, complex logic functions.
Parallel expanders allow up to 20 product terms to directly feed the
macrocell ORlogic, with five product terms provided by the macrocell and
15 parallel expanders provided by neighboring macrocells in the LAB.
The Altera Compiler can automatically allocate up to three sets of up to
five parallel expanders to the macrocells that require additional product
terms. Each set of five parallel expanders incurs a small, incremental
timing delay (tPEXP). For example, if a macrocell requires 14 product
terms, the Compiler uses the five dedicated product terms within the
macrocell and allocates two sets of parallel expanders; the first set
includes five product terms and the second set includes four product
terms, increasing the total delay by 2 × tPEXP
.
Two groups of eight macrocells within each LAB (e.g., macrocells 1
through 8, and 9 through 16) form two chains to lend or borrow parallel
expanders. A macrocell borrows parallel expanders from lower-
numbered macrocells. For example, macrocell 8 can borrow parallel
expanders from macrocell 7, from macrocells 7 and 6, or from macrocells
7, 6, and 5. Within each group of eight, the lowest-numbered macrocell
can only lend parallel expanders and the highest-numbered macrocell can
only borrow them. Figure 4 shows how parallel expanders can be
borrowed from a neighboring macrocell.
10
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 4. MAX 7000B Parallel Expanders
Unused product terms in a macrocell can be allocated to a neighboring macrocell.
From
Previous
Macrocell
Preset
Product-
Term
Select
Matrix
Macrocell
Product-
Term Logic
Clock
Clear
Preset
Product-
Term
Select
Matrix
Macrocell
Product-
Term Logic
Clock
Clear
To Next
Macrocell
36 Signals 16 Shared
from PIA
Expanders
Programmable Interconnect Array
Logic is routed between LABs on the PIA. This global bus is a
programmable path that connects any signal source to any destination on
the device. All MAX 7000B dedicated inputs, I/O pins, and macrocell
outputs feed the PIA, which makes the signals available throughout the
entire device. Only the signals required by each LAB are actually routed
from the PIA into the LAB. Figure 5 shows how the PIA signals are routed
into the LAB. An EEPROM cell controls one input to a two-input ANDgate,
which selects a PIA signal to drive into the LAB.
Altera Corporation
11
MAX 7000B Programmable Logic Device Data Sheet
Figure 5. MAX 7000B PIA Routing
To LAB
PIA Signals
While the routing delays of channel-based routing schemes in masked or
field-programmable gate arrays (FPGAs) are cumulative, variable, and
path-dependent, the MAX 7000B PIA has a predictable delay. The PIA
makes a design’s timing performance easy to predict.
I/O Control Blocks
The I/O control block allows each I/O pin to be individually configured
for input, output, or bidirectional operation. All I/O pins have a tri-state
buffer that is individually controlled by one of the global output enable
signals or directly connected to ground or VCC. Figure 6 shows the I/O
control block for MAX 7000B devices. The I/O control block has
six or ten global output enable signals that are driven by the true or
complement of two output enable signals, a subset of the I/O pins, or a
subset of the I/O macrocells.
12
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 6. I/O Control Block of MAX 7000B Devices
6 or 10 Global
Output Enable Signals (1)
PIA
OE Select Multiplexer
VCC
Programmable
to Other I/O Pins
GND
Pull-up
from
Macrocell
Open-Drain Output
Slew-Rate Control
I/O Standards
Bus Hold
Programmable
Ground
Fast Input to
Macrocell
Register
Programmable Delay
to PIA
Note:
(1) EPM7032B, EPM7064B, EPM7128B, and EPM7256B devices have six output enable signals. EPM7512B devices have
ten output enable signals.
When the tri-state buffer control is connected to ground, the output is
tri-stated (high impedance) and the I/O pin can be used as a dedicated
input. When the tri-state buffer control is connected to VCC, the output is
enabled.
The MAX 7000B architecture provides dual I/O feedback, in which
macrocell and pin feedbacks are independent. When an I/O pin is
configured as an input, the associated macrocell can be used for buried
logic.
Altera Corporation
13
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices support the SameFrame pin-out feature for
SameFrame
Pin-Outs
FineLine BGA and 0.8-mm Ultra FineLine BGA packages. The
SameFrame pin-out feature is the arrangement of balls on FineLine BGA
and 0.8-mm Ultra FineLine BGA packages such that the lower-ball-count
packages form a subset of the higher-ball-count packages. SameFrame
pin-outs provide the flexibility to migrate not only from device to device
within the same package, but also from one package to another. FineLine
BGA packages are compatible with other FineLine BGA packages, and
0.8-mm Ultra FineLine BGA packages are compatible with other 0.8-mm
Ultra FineLine BGA packages. A given printed circuit board (PCB) layout
can support multiple device density/package combinations. For example,
a single board layout can support a range of devices from an EPM7064B
device in a 100-pin FineLine BGA package to an EPM7512B device in a
256-pin FineLine BGA package.
The Altera software provides support to design PCBs with SameFrame
pin-out devices. Devices can be defined for present and future use. The
Altera software generates pin-outs describing how to layout a board to
take advantage of this migration (see Figure 7).
Figure 7. SameFrame Pin-Out Example
Printed Circuit Board
Designed for 256-Pin FineLine BGA Package
100-Pin
FineLine
BGA
256-Pin
FineLine
BGA
100-Pin FineLine BGA Package
(Reduced I/O Count or
256-Pin FineLine BGA Package
(Increased I/O Count or
Logic Requirements)
Logic Requirements)
14
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices can be programmed in-system via an industry-
standard 4-pin IEEE Std. 1149.1 (JTAG) interface. ISP offers quick, efficient
iterations during design development and debugging cycles. The
MAX 7000B architecture internally generates the high programming
voltages required to program EEPROM cells, allowing in-system
programming with only a single 2.5-V power supply. During in-system
programming, the I/O pins are tri-stated and weakly pulled-up to
eliminate board conflicts. The pull-up value is nominally 50 k¾.
In-System
Programma-
bility (ISP)
MAX 7000B devices have an enhanced ISP algorithm for faster
programming. These devices also offer an ISP_Done bit that provides safe
operation when in-system programming is interrupted. This ISP_Done
bit, which is the last bit programmed, prevents all I/O pins from driving
until the bit is programmed.
ISP simplifies the manufacturing flow by allowing devices to be mounted
on a PCB with standard pick-and-place equipment before they are
programmed. MAX 7000B devices can be programmed by downloading
the information via in-circuit testers, embedded processors, the Altera
MasterBlaster communications cable, and the ByteBlasterMV parallel port
download cable. Programming the devices after they are placed on the
board eliminates lead damage on high-pin-count packages (e.g., QFP
packages) due to device handling. MAX 7000B devices can be
reprogrammed after a system has already shipped to the field. For
example, product upgrades can be performed in the field via software or
modem.
In-system programming can be accomplished with either an adaptive or
constant algorithm. An adaptive algorithm reads information from the
unit and adapts subsequent programming steps to achieve the fastest
possible programming time for that unit. A constant algorithm uses a
pre-defined (non-adaptive) programming sequence that does not take
advantage of adaptive algorithm programming time improvements.
Some in-circuit testers cannot program using an adaptive algorithm.
Therefore, a constant algorithm must be used. MAX 7000B devices can be
programmed with either an adaptive or constant (non-adaptive)
algorithm.
The Jam Standard Test and Programming Language (STAPL), JEDEC
standard JESD-71, can be used to program MAX 7000B devices with
in-circuit testers, PCs, or embedded processors.
For more information on using the Jam language, see Application Note 88
(Using the Jam Language for ISP & ICR via an Embedded Processor) and
Application Note 122 (Using STAPL for ISP & ICR via an Embedded Processor).
f
The ISP circuitry in MAX 7000B devices is compliant with the IEEE
Std. 1532 specification. The IEEE Std. 1532 is a standard developed to
allow concurrent ISP between multiple PLD vendors.
Altera Corporation
15
MAX 7000B Programmable Logic Device Data Sheet
Programming Sequence
During in-system programming, instructions, addresses, and data are
shifted into the MAX 7000B device through the TDIinput pin. Data is
shifted out through the TDOoutput pin and compared against the
expected data.
Programming a pattern into the device requires the following six ISP
stages. A stand-alone verification of a programmed pattern involves only
stages 1, 2, 5, and 6.
1. Enter ISP. The enter ISP stage ensures that the I/O pins transition
smoothly from user mode to ISP mode. The enter ISP stage requires
1 ms.
2. Check ID. Before any program or verify process, the silicon ID is
checked. The time required to read this silicon ID is relatively small
compared to the overall programming time.
3. Bulk Erase. Erasing the device in-system involves shifting in the
instructions to erase the device and applying one erase pulse of
100 ms.
4. Program. Programming the device in-system involves shifting in the
address and data and then applying the programming pulse to
program the EEPROM cells. This process is repeated for each
EEPROM address.
5. Verify. Verifying an Altera device in-system involves shifting in
addresses, applying the read pulse to verify the EEPROM cells, and
shifting out the data for comparison. This process is repeated for
each EEPROM address.
6. Exit ISP. An exit ISP stage ensures that the I/O pins transition
smoothly from ISP mode to user mode. The exit ISP stage requires
1 ms.
Programming Times
The time required to implement each of the six programming stages can
be broken into the following two elements:
■
■
A pulse time to erase, program, or read the EEPROM cells.
A shifting time based on the test clock (TCK) frequency and the
number of TCKcycles to shift instructions, address, and data into the
device.
16
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
By combining the pulse and shift times for each of the programming
stages, the program or verify time can be derived as a function of the TCK
frequency, the number of devices, and specific target device(s). Because
different ISP-capable devices have a different number of EEPROM cells,
both the total fixed and total variable times are unique for a single device.
Programming a Single MAX 7000B Device
The time required to program a single MAX 7000B device in-system can
be calculated from the following formula:
Cycle
PTCK
t
= t
+ -------------------------------
PROG
PPULSE
f
TCK
where: tPROG
= Programming time
= Sum of the fixed times to erase, program, and
verify the EEPROM cells
tPPULSE
CyclePTCK = Number of TCKcycles to program a device
fTCK = TCKfrequency
The ISP times for a stand-alone verification of a single MAX 7000B device
can be calculated from the following formula:
Cycle
VTCK
t
= t
+ --------------------------------
VER
VPULSE
f
TCK
where: tVER
tVPULSE
CycleVTCK = Number of TCKcycles to verify a device
= Verify time
= Sum of the fixed times to verify the EEPROM cells
Altera Corporation
17
MAX 7000B Programmable Logic Device Data Sheet
The programming times described in Tables 4 through 6 are associated
with the worst-case method using the enhanced ISP algorithm.
Table 4. MAX 7000B tPULSE & CycleTCK Values
Device
Programming
Stand-Alone Verification
tVPULSE (s) CycleVTCK
tPPULSE (s)
CyclePTCK
EMP7032B
EMP7064B
EMP7128B
EMP7256B
EMP7512B
2.12
2.12
2.12
2.12
2.12
70,000
120,000
222,000
466,000
914,000
0.002
0.002
0.002
0.002
0.002
18,000
35,000
69,000
151,000
300,000
Tables 5 and 6 show the in-system programming and stand alone
verification times for several common test clock frequencies.
Table 5. MAX 7000B In-System Programming Times for Different Test Clock Frequencies
Device
fTCK
Units
10 MHz 5 MHz
2 MHz
1 MHz 500 kHz 200 kHz 100 kHz 50 kHz
EMP7032B
EMP7064B
EMP7128B
EMP7256B
EMP7512B
2.13
2.13
2.14
2.17
2.21
2.13
2.14
2.16
2.21
2.30
2.15
2.18
2.23
2.35
2.58
2.19
2.24
2.34
2.58
3.03
2.26
2.36
2.56
3.05
3.95
2.47
2.72
3.23
4.45
6.69
2.82
3.32
4.34
6.78
11.26
3.52
4.52
s
s
s
s
s
6.56
11.44
20.40
Table 1. MAX 7000B Stand-Alone Verification Times for Different Test Clock Frequencies
Device
fTCK
1 MHz 500 kHz 200 kHz 100 kHz 50 kHz
Units
10 MHz 5 MHz
2 MHz
EMP7032B
EMP7064B
EMP7128B
EMP7256B
EMP7512B
0.00
0.01
0.01
0.02
0.03
0.01
0.01
0.02
0.03
0.06
0.01
0.02
0.04
0.08
0.15
0.02
0.04
0.07
0.15
0.30
0.04
0.07
0.14
0.30
0.60
0.09
0.18
0.35
0.76
1.50
0.18
0.35
0.69
1.51
3.00
0.36
0.70
1.38
3.02
6.00
s
s
s
s
s
18
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices can be programmed on Windows-based PCs with an
Altera Logic Programmer card, the Master Programming Unit (MPU),
and the appropriate device adapter. The MPU performs continuity
checking to ensure adequate electrical contact between the adapter and
the device.
Programming
with External
Hardware
For more information, see the Altera Programming Hardware Data Sheet.
f
The Altera software can use text- or waveform-format test vectors created
with the Altera Text Editor or Waveform Editor to test the programmed
device. For added design verification, designers can perform functional
testing to compare the functional device behavior with the results of
simulation.
Data I/O, BP Microsystems, and other programming hardware
manufacturers provide programming support for Altera devices. For
more information, see Programming Hardware Manufacturers.
MAX 7000B devices include the JTAG boundary-scan test circuitry
defined by IEEE Std. 1149.1. Table 6 describes the JTAG instructions
supported by MAX 7000B devices. The pin-out tables starting on page 59
of this data sheet show the location of the JTAG control pins for each
device. If the JTAG interface is not required, the JTAG pins are available
as user I/O pins.
IEEE Std.
1149.1 (JTAG)
Boundary-Scan
Support
Table 6. MAX 7000B JTAG Instructions
JTAG Instruction
Description
SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during
normal device operation, and permits an initial data pattern output at the device pins.
EXTEST
Allows the external circuitry and board-level interconnections to be tested by forcing a
test pattern at the output pins and capturing test results at the input pins.
BYPASS
Places the 1-bit bypass register between the TDIand TDOpins, which allows the
boundary-scan test data to pass synchronously through a selected device to adjacent
devices during normal operation.
CLAMP
Allows the values in the boundary-scan register to determine pin states while placing the
1-bit bypass register between the TDIand TDOpins.
IDCODE
Selects the IDCODE register and places it between the TDIand TDOpins, allowing the
IDCODE to be serially shifted out of TDO.
USERCODE
ISP Instructions
Selects the 32-bit USERCODE register and places it between the TDIand TDOpins,
allowing the USERCODE value to be shifted out of TDO.
These instructions are used when programming MAX 7000B devices via the JTAG ports
with the MasterBlaster or ByteBlasterMV download cable, or using a Jam File (.jam),
Jam Byte-Code File (.jbc), or Serial Vector Format File (.svf) via an embedded
processor or test equipment.
Altera Corporation
19
MAX 7000B Programmable Logic Device Data Sheet
The instruction register length of MAX 7000B devices is ten bits. The
MAX 7000B USERCODE register length is 32 bits. Tables 7 and 8 show the
boundary-scan register length and device IDCODE information for
MAX 7000B devices.
Table 7. MAX 7000B Boundary-Scan Register Length
Device
Boundary-Scan Register Length
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
96
192
288
480
624
Table 8. 32-Bit MAX 7000B Device IDCODE Note (1)
Device
IDCODE (32 Bits)
Version
(4 Bits)
Part Number (16 Bits) Manufacturer’s 1 (1 Bit)
Identity (11 Bits)
(2)
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
0010
0010
0010
0010
0010
0111 0000 0011 0010 00001101110
0111 0000 0110 0100 00001101110
0111 0001 0010 1000 00001101110
0111 0010 0101 0110 00001101110
0111 0101 0001 0010 00001101110
1
1
1
1
1
Notes:
(1) The most significant bit (MSB) is on the left.
(2) The least significant bit (LSB) for all JTAG IDCODEs is 1.
See Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera
Devices) for more information on JTAG boundary-scan testing.
f
Figure 8 shows the timing information for the JTAG signals.
20
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 8. MAX 7000B JTAG Waveforms
TMS
TDI
tJCP
tJCH
t JCL
tJPH
tJPSU
TCK
TDO
tJPXZ
tJPZX
tJPCO
tJSSU
tJSH
Signal
to Be
Captured
tJSCO
tJSZX
tJSXZ
Signal
to Be
Driven
Table 9 shows the JTAG timing parameters and values for MAX 7000B
devices.
Table 9. JTAG Timing Parameters & Values for MAX 7000B Devices
Note (1)
Symbol
Parameter
Min Max Unit
t
TCKclock period
100
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
JCP
t
TCKclock high time
50
JCH
t
TCKclock low time
50
JCL
t
JTAG port setup time
20
45
JPSU
t
JTAG port hold time
JPH
t
JTAG port clock to output
25
25
25
JPCO
t
JTAG port high impedance to valid output
JTAG port valid output to high impedance
Capture register setup time
JPZX
t
JPXZ
t
20
45
JSSU
t
Capture register hold time
JSH
t
Update register clock to output
Update register high impedance to valid output
Update register valid output to high impedance
25
25
25
JSCO
t
JSZX
t
JSXZ
Note:
(1) Timing parameters in this table apply to all V
levels.
CCIO
Altera Corporation
21
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices offer a power-saving mode that supports low-power
Programmable
Speed/Power
Control
operation across user-defined signal paths or the entire device. This
feature allows total power dissipation to be reduced by 50% or more,
because most logic applications require only a small fraction of all gates to
operate at maximum frequency.
The designer can program each individual macrocell in a MAX 7000B
device for either high-speed or low-power operation. As a result, speed-
critical paths in the design can run at high speed, while the remaining
paths can operate at reduced power. Macrocells that run at low power
incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC, tACL
tCPPW, tEN, and tSEXP parameters.
,
MAX 7000B device outputs can be programmed to meet a variety of
system-level requirements.
Output
Configuration
MultiVolt I/O Interface
The MAX 7000B device architecture supports the MultiVolt I/O interface
feature, which allows MAX 7000B devices to connect to systems with
differing supply voltages. MAX 7000B devices in all packages can be set
for 3.3-V, 2.5-V, or 1.8-V pin operation. These devices have one set of VCC
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
The VCCIOpins can be connected to either a 3.3-V, 2.5-V, or 1.8-V power
supply, depending on the output requirements. When the VCCIOpins are
connected to a 1.8-V power supply, the output levels are compatible with
1.8-V systems. When the VCCIOpins are connected to a 2.5-V power
supply, the output levels are compatible with 2.5-V systems. When the
VCCIOpins are connected to a 3.3-V power supply, the output high is at
3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices
operating with VCCIO levels of 2.5 V or 1.8 V incur a nominal timing delay
adder.
Table 10 describes the MAX 7000B MultiVolt I/O support.
22
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 10. MAX 7000B MultiVolt I/O Support
VCCIO (V)
Input Signal (V)
Output Signal (V)
1.8
2.5
3.3
5.0
1.8
2.5
3.3
5.0
1.8
2.5
3.3
v
v
v
v
v
v
v
v
v
v
v
v
v
Open-Drain Output Option
MAX 7000B devices provide an optional open-drain (equivalent to
open-collector) output for each I/O pin. This open-drain output enables
the device to provide system-level control signals (e.g., interrupt and
write enable signals) that can be asserted by any of several devices. It can
also provide an additional wired-ORplane.
Programmable Ground Pins
Each unused I/O pin on MAX 7000B devices may be used as an additional
ground pin. This programmable ground feature does not require the use
of the associated macrocell; therefore, the buried macrocell is still
available for user logic.
Slew-Rate Control
The output buffer for each MAX 7000B I/O pin has an adjustable output
slew rate that can be configured for low-noise or high-speed performance.
A faster slew rate provides high-speed transitions for high-performance
systems. However, these fast transitions may introduce noise transients
into the system. A slow slew rate reduces system noise, but adds a
nominal delay of 4 to 5 ns. When the configuration cell is turned off, the
slew rate is set for low-noise performance. Each I/O pin has an individual
EEPROM bit that controls the slew rate, allowing designers to specify the
slew rate on a pin-by-pin basis. The slew rate control affects both the rising
and falling edges of the output signal.
Advanced I/O Standard Support
The MAX 7000B I/O pins support the following I/O standards: LVTTL,
LVCMOS, 1.8-V I/O, 2.5-V I/O, GTL+, SSTL-3 Class I and II, and SSTL-2
Class I and II.
Altera Corporation
23
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B devices contain two I/O banks. Both banks support all
standards. Each I/O bank has its own VCCIOpins. A single device can
support 1.8-V, 2.5-V, and 3.3-V interfaces; each bank can support a
different standard independently. Within a bank, any one of the
terminated standards can be supported.
Figure 9 shows the arrangement of the MAX 7000B I/O banks.
Figure 9. MAX 7000B I/O Banks for Various Advanced I/O Standards
Programmable I/O Banks
Individual
Power Bus
Table 11 shows which macrocells have pins in each I/O bank.
Table 11. Macrocell Pins Contained in Each I/O Bank
Device
Bank 1
Bank 2
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
1-16
1-32
17-32
33-64
1-64
65-128
1-128, 177-181
1-265
129-176, 182-256
266-512
Each MAX 7000B device has two VREFpins. Each can be set to a separate
VREF level. Any I/O pin that uses one of the voltage-referenced standards
(GTL+, SSTL-2, or SSTL-3) may use either of the two VREFpins. If these
pins are not required as VREFpins, they may be individually
programmed to function as user I/O pins.
24
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Programmable Pull-Up Resistor
Each MAX 7000B device I/O pin provides an optional programmable
pull-up resistor during user mode. When this feature is enabled for an I/O
pin, the pull-up resistor (typically 50 k¾) weakly holds the output to
VCCIO level.
Bus Hold
Each MAX 7000B device I/O pin provides an optional bus-hold feature.
When this feature is enabled for an I/O pin, the bus-hold circuitry weakly
holds the signal at its last driven state. By holding the last driven state of
the pin until the next input signals is present, the bus-hold feature can
eliminate the need to add external pull-up or pull-down resistors to hold
a signal level when the bus is tri-stated. The bus-hold circuitry also pulls
undriven pins away from the input threshold voltage where noise can
cause unintended high-frequency switching. This feature can be selected
individually for each I/O pin. The bus-hold output will drive no higher
than VCCIO to prevent overdriving signals. The propagation delays
through the input and output buffers in MAX 7000B devices are not
affected by whether the bus-hold feature is enabled or disabled.
The bus-hold circuitry weakly pulls the signal level to the last driven state
through a resistor with a nominal resistance (RBH) of approximately
8.5 k¾. Table 12 gives specific sustaining current that will be driven
through this resistor and overdrive current that will identify the next
driven input level. This information is provided for each VCCIO voltage
level.
Table 12. Bus Hold Parameters
Parameter
Conditions
VCCIO Level
2.5 V
Units
1.8 V
3.3 V
Min Max Min Max Min Max
Low sustaining current
VIN > VIL (max)
30
50
70
μA
μA
μA
μA
High sustaining current VIN < VIH (min)
–30
–50
–70
Low overdrive current
High overdrive current
0 V < VIN < VCCIO
0 V < VIN < VCCIO
200
300
500
–295
–435
–680
The bus-hold circuitry is active only during user operation. At power-up,
the bus-hold circuit initializes its initial hold value as VCC approaches the
recommended operation conditions. When transitioning from ISP to User
Mode with bus hold enabled, the bus-hold circuit captures the value
present on the pin at the end of programming.
Altera Corporation
25
MAX 7000B Programmable Logic Device Data Sheet
Two inverters implement the bus-hold circuitry in a loop that weakly
drives back to the I/O pin in user mode.
Figure 10 shows a block diagram of the bus-hold circuit.
Figure 10. Bus-Hold Circuit
Bus Hold Circuit
Drive to
VCCIO level
R
BH
I/O
MAX 7000B devices are compatible with PCI applications as well as all
3.3-V electrical specifications in the PCI Local Bus Specification
Revision 2.2 except for the clamp diode. While having multiple clamp
diodes on a signal trace may be redundant, designers can add an external
clamp diode to meet the specification. Table 13 shows the MAX 7000B
device speed grades that meet the PCI timing specifications.
PCI
Compatibility
Table 13. MAX 7000B Device Speed Grades that Meet PCI Timing
Specifications
Device
Specification
33-MHz PCI
66-MHz PCI
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
All speed grades
All speed grades
All speed grades
All speed grades
All speed grades
-3
-3
-4
-5 (1)
-5 (1)
Note:
(1) The EPM7256B and EPM7512B devices in a -5 speed grade meet all PCI timing
specifications for 66-MHz operation except the Input Setup Time to CLK—Bused
Signal parameter. However, these devices are within 1 ns of that parameter.
EPM7256B and EPM7512B devices meet all other 66-MHz PCI timing
specifications.
26
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Because MAX 7000B devices can be used in a mixed-voltage environment,
they have been designed specifically to tolerate any possible power-up
sequence. The VCCIO and VCCINT power planes can be powered in any
order.
Power
Sequencing &
Hot-Socketing
Signals can be driven into MAX 7000B devices before and during power-
up (and power-down) without damaging the device. Additionally,
MAX 7000B devices do not drive out during power-up. Once operating
conditions are reached, MAX 7000B devices operate as specified by the
user.
MAX 7000B device I/O pins will not source or sink more than 300 µA of
DC current during power-up. All pins can be driven up to 4.1 V during
hot-socketing.
All MAX 7000B devices contain a programmable security bit that controls
access to the data programmed into the device. When this bit is
programmed, a design implemented in the device cannot be copied or
retrieved. This feature provides a high level of design security, because
programmed data within EEPROM cells is invisible. The security bit that
controls this function, as well as all other programmed data, is reset only
when the device is reprogrammed.
Design Security
Generic Testing
MAX 7000B devices are fully functionally tested. Complete testing of each
programmable EEPROM bit and all internal logic elements ensures 100%
programming yield. AC test measurements are taken under conditions
equivalent to those shown in Figure 11. Test patterns can be used and then
erased during early stages of the production flow.
Altera Corporation
27
MAX 7000B Programmable Logic Device Data Sheet
Figure 11. MAX 7000B AC Test Conditions
Power supply transients can affect AC
measurements. Simultaneous transitions
of multiple outputs should be avoided for
accurate measurement. Threshold tests
must not be performed under AC
VCCIO
S1
conditions. Large-amplitude, fast-ground-
current transients normally occur as the
device outputs discharge the load
capacitances. When these transients flow
through the parasitic inductance between
the device ground pin and the test system
ground, significant reductions in
720 Ω
[521 Ω]
Device
Output
To Test
System
observable noise immunity can result.
Numbers in brackets are for 2.5-V
outputs. Numbers without brackets are for
3.3-V outputs. Switches S1 and S2 are
open for all tests except output disable
timing parameters.
600 Ω
[481 Ω]
C1 (includes jig
capacitance)
Device input
rise and fall
times < 2 ns
S2
Tables 14 through 17 provide information on absolute maximum ratings,
recommended operating conditions, operating conditions, and
capacitance for MAX 7000B devices.
Operating
Conditions
Table 14. MAX 7000B Device Absolute Maximum Ratings
Note (1)
Symbol
Parameter
Conditions
Min
Max
Unit
V
Supply voltage
–0.5
–0.5
–2.0
–33
–65
–65
–65
3.6
3.6
4.6
50
V
V
CCINT
V
Supply voltage
CCIO
V
I
DC input voltage
(2)
V
I
DC output current, per pin
Storage temperature
Ambient temperature
Junction temperature
mA
° C
° C
° C
OUT
T
No bias
150
135
135
STG
T
A
Under bias
Under bias
T
J
28
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 15. MAX 7000B Device Recommended Operating Conditions
Symbol
Parameter
Conditions
Min
Max
Unit
V
Supply voltage for internal logic and (10)
input buffers
2.375
2.625
V
CCINT
V
Supply voltage for output drivers,
3.3-V operation
3.0
3.6
V
V
V
V
CCIO
Supply voltage for output drivers,
2.5-V operation
2.375
1.71
2.625
1.89
Supply voltage for output drivers,
1.8-V operation
V
Supply voltage during in-system
programming
2.375
2.625
CCISP
V
I
Input voltage
(3)
–0.5
0
3.9
VCCIO
70
V
V
O
Output voltage
V
T
A
Ambient temperature
For commercial use
For industrial use (11)
For commercial use
For industrial use (11)
0
° C
° C
° C
° C
ns
–40
0
85
T
J
Junction temperature
90
–40
105
40
t
Input rise time
Input fall time
R
t
40
ns
F
Altera Corporation
29
MAX 7000B Programmable Logic Device Data Sheet
Table 16. MAX 7000B Device DC Operating Conditions
Note (4)
Symbol
Parameter
Conditions
Min
Max
Unit
V
High-level input voltage for 3.3-V
TTL/CMOS
2.0
3.9
V
IH
High-level input voltage for 2.5-V
TTL/CMOS
1.7
3.9
3.9
V
V
High-level input voltage for 1.8-V
TTL/CMOS
0.65 ×
VCCIO
V
IL
Low-level input voltage for 3.3-V
TTL/CMOS and PCI compliance
–0.5
–0.5
–0.5
0.8
0.7
V
V
Low-level input voltage for 2.5-V
TTL/CMOS
Low-level input voltage for 1.8-V
TTL/CMOS
0.35 ×
VCCIO
V
3.3-V high-level TTL output voltage
I
I
= –8 mA DC, V
= 3.00 V (5)
2.4
V
V
OH
OH
CCIO
3.3-V high-level CMOS output
voltage
= –0.1 mA DC, V
= 3.00 V (5)
= 2.30 V (5)
CCIO
VCCIO
0.2
–
OH
CCIO
2.5-V high-level output voltage
I
I
I
I
I
I
= –100 μA DC, V
2.1
2.0
1.7
1.2
V
V
V
V
V
V
OH
OH
OH
OH
OL
OL
= –1 mA DC, V
= 2.30 V (5)
= 2.30 V (5)
=1.65 V (5)
CCIO
= –2 mA DC, V
= –2 mA DC, V
= 8 mA DC, V
CCIO
CCIO
1.8-V high-level output voltage
V
3.3-V low-level TTL output voltage
= 3.00 V (6)
= 3.00 V (6)
0.4
0.2
OL
CCIO
3.3-V low-level CMOS output
voltage
= 0.1 mA DC, V
CCIO
2.5-V low-level output voltage
I
I
I
I
= 100 μA DC, V
= 2.30 V (6)
CCIO
0.2
0.4
0.7
0.4
10
V
V
OL
OL
OL
OL
= 1 mA DC, V
= 2.30 V (6)
= 2.30 V (6)
= 1.7 V (6)
CCIO
= 2 mA DC, V
= 2 mA DC, V
V
CCIO
CCIO
1.8-V low-level output voltage
Input leakage current
V
I
I
V = –0.5 to 3.9 V (7)
–10
–10
20
μA
μA
k¾
I
I
Tri-state output off-state current
V = –0.5 to 3.9 V (7)
10
OZ
I
R
Value of I/O pin pull-up resistor
during in-system programming or
during power up
V
= 1.7 to 3.6 V (8)
CCIO
74
ISP
30
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 17. MAX 7000B Device Capacitance
Note (9)
Symbol
Parameter
Conditions
Min
Max
Unit
C
Input pin capacitance
V
V
= 0 V, f = 1.0 MHz
= 0 V, f = 1.0 MHz
OUT
8
8
pF
pF
IN
IN
C
I/O pin capacitance
I/O
Notes to tables:
(1) See the Operating Requirements for Altera Devices Data Sheet.
(2) Minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to 4.6 V
for input currents less than 100 mA and periods shorter than 20 ns.
(3) All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before V
powered.
and V
are
CCINT
CCIO
(4) These values are specified under the Recommended Operating Conditions in Table 15 on page 29.
(5) The parameter is measured with 50% of the outputs each sourcing the specified current. The I
parameter refers
OH
to high-level TTL or CMOS output current.
(6) The parameter is measured with 50% of the outputs each sinking the specified current. The I parameter refers to
OL
low-level TTL or CMOS output current.
(7) This value is specified for normal device operation. During power-up, the maximum leakage current is 300 μA.
(8) This pull-up exists while devices are being programmed in-system and in unprogrammed devices during
power-up. The pull-up resistor is from the pins to V
.
CCIO
(9) Capacitance is measured at 25° C and is sample-tested only. Two of the dedicated input pins (OE1and GCLRN) have
a maximum capacitance of 15 pF.
(10) The POR time for all 7000B devices does not exceed 100 μs. The sufficient V
voltage level for POR is 2.375 V.
CCINT
The device is fully initialized within the POR time after V
reaches the sufficient POR voltage level.
CCINT
(11) These devices support in-system programming for –40° to 100° C. For in-system programming support between
–40° and 0° C, contact Altera Applications.
Altera Corporation
31
MAX 7000B Programmable Logic Device Data Sheet
Figure 12 shows the typical output drive characteristics of MAX 7000B
devices.
Figure 12. Output Drive Characteristics of MAX 7000B Devices
3.3-V VCCIO
2.5-V VCCIO
150
120
150
IOL
IOL
120
VCCINT = 2.5 V
VCCIO = 3.0 V
Typical IO
Output
Current (mA)
Typical IO
Output
90
60
90
60
VCCINT = 2.5 V
VCCIO = 2.5 V
Room Temperature Current (mA)
Room Temperature
30
30
IOH
IOH
1
2
3
4
1
2
3
4
VO Output Voltage (V)
VO Output Voltage (V)
1.8-V VCCIO
150
IOL
120
Typical IO
Output
Current (mA)
90
60
VCCINT = 2.5 V
VCCIO = 1.8 V
Room Temperature
30
IOH
1
2
3
4
VO Output Voltage (V)
32
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
MAX 7000B device timing can be analyzed with the Altera software, with
a variety of popular industry-standard EDA simulators and timing
analyzers, or with the timing model shown in Figure 13. MAX 7000B
devices have predictable internal delays that enable the designer to
determine the worst-case timing of any design. The Altera software
provides timing simulation, point-to-point delay prediction, and detailed
timing analysis for device-wide performance evaluation.
Timing Model
Figure 13. MAX 7000B Timing Model
Internal Output
Enable Delay
tIOE
Global Control
Delay
Input
Delay
t I N
Output
Delay
tGLOB
Register
Delay
tSU
Parallel
Expander Delay
tPEXP
Logic Array
Delay
t LAD
tOD1
tOD2
tOD3
tXZ
tZX1
tZX2
tZX3
PIA
Delay
tPIA
tH
tPRE
tCLR
tRD
tCOMB
tFSU
tFH
Register
Control Delay
tLAC
tIC
tEN
I/O
Delay
tIO
Shared
Expander Delay
tSEXP
Fast
Input Delay
tFIN
+
tFIN tFIND
The timing characteristics of any signal path can be derived from the
timing model and parameters of a particular device. External timing
parameters, which represent pin-to-pin timing delays, can be calculated
as the sum of internal parameters. Figure 14 shows the timing relationship
between internal and external delay parameters.
See Application Note 94 (Understanding MAX 7000 Timing) for more
information.
f
Altera Corporation
33
MAX 7000B Programmable Logic Device Data Sheet
Figure 14. MAX 7000B Switching Waveforms
tR & tF < 2 ns. Inputs are
driven at 3.0 V for a logic
high and 0 V for a logic
low. All timing
characteristics are
measured at 1.5 V.
Combinatorial Mode
tIN
Input Pin
I/O Pin
tIO
tPIA
PIA Delay
tSEXP
Shared Expander
Delay
tLAC , tLAD
Logic Array
Input
tPEXP
Parallel Expander
Delay
tCOMB
Logic Array
Output
tOD
Output Pin
Global Clock Mode
tR
tCH
tCL
tF
Global
Clock Pin
tIN
tGLOB
Global Clock
at Register
tSU
tH
Data or Enable
(Logic Array Output)
Array Clock Mode
tR
tACH
tACL
tF
Input or I/O Pin
Clock into PIA
tIN
tIO
tPIA
Clock into
Logic Array
tIC
tSU
Clock at
Register
tH
Data from
Logic Array
tRD
tPIA
tPIA
tCLR , tPRE
Register to PIA
to Logic Array
tOD
tOD
Register Output
to Pin
34
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Tables 18 through 32 show MAX 7000B device timing parameters.
Table 18. EPM7032B External Timing Parameters
Notes (1)
Symbol
Parameter
Conditions
Speed Grade
-5.0
Unit
-3.5
-7.5
Min
Max
Min
Max
Min
Max
t
Input to non-registered
output
C1 = 35 pF (2)
3.5
5.0
7.5
ns
ns
PD1
t
I/O input to non-registered C1 = 35 pF (2)
output
3.5
5.0
7.5
PD2
t
t
t
Global clock setup time
Global clock hold time
(2)
(2)
2.1
0.0
1.0
3.0
0.0
1.0
4.5
0.0
1.5
ns
ns
ns
SU
H
Global clock setup time of
fast input
FSU
t
Global clock hold time of
fast input
1.0
2.0
1.0
2.5
1.0
3.0
ns
ns
FH
t
Global clock setup time of
fast input with zero hold
time
FZHSU
t
t
Global clock hold time of
fast input with zero hold
time
0.0
1.0
0.0
1.0
0.0
1.0
ns
ns
FZHH
Global clock to output
delay
C1 = 35 pF
2.4
3.6
3.4
5.1
5.0
7.6
CO1
t
t
t
t
t
t
t
t
Global clock high time
Global clock low time
Array clock setup time
Array clock hold time
1.5
1.5
0.9
0.2
1.0
1.5
1.5
1.5
2.0
2.0
1.3
0.3
1.0
2.0
2.0
2.0
3.0
3.0
1.9
0.6
1.0
3.0
3.0
3.0
ns
ns
ns
ns
ns
ns
ns
ns
CH
CL
(2)
(2)
ASU
AH
Array clock to output delay C1 = 35 pF (2)
Array clock high time
ACO1
ACH
ACL
CPPW
Array clock low time
Minimum pulse width for
clear and preset
t
f
t
f
Minimum global clock
period
(2)
3.3
3.3
4.7
4.7
7.0
7.0
ns
MHz
ns
CNT
Maximum internal global
clock frequency
(2), (3)
(2)
303.0
303.0
212.8
212.8
142.9
142.9
CNT
Minimum array clock
period
ACNT
ACNT
Maximum internal array
clock frequency
(2), (3)
MHz
Altera Corporation
35
MAX 7000B Programmable Logic Device Data Sheet
Table 19. EPM7032B Internal Timing Parameters
Notes (1)
Symbol
Parameter
Conditions
Speed Grade
-5.0
Unit
-3.5
-7.5
Min Max Min Max Min Max
Input pad and buffer delay
I/O input pad and buffer delay
Fast input delay
tIN
0.3
0.3
0.9
1.0
0.5
0.5
1.3
1.5
0.7
0.7
2.0
1.5
ns
ns
ns
ns
tIO
tFIN
tFIND
Programmable delay adder for
fast input
Shared expander delay
Parallel expander delay
Logic array delay
tSEXP
tPEXP
tLAD
tLAC
tIOE
1.5
0.4
1.4
1.2
0.1
0.9
2.1
0.6
2.0
1.7
0.2
1.2
3.2
0.9
3.1
2.6
0.3
1.8
ns
ns
ns
ns
ns
ns
Logic control array delay
Internal output enable delay
Output buffer and pad delay
slow slew rate = off
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
tOD1
V
= 3.3 V
CCIO
Output buffer and pad delay
slow slew rate = on
tOD3
tZX1
tZX3
5.9
1.6
6.6
1.6
6.2
2.2
7.2
2.2
6.8
3.4
8.4
3.4
ns
ns
ns
V
= 2.5 V or 3.3 V
CCIO
Output buffer enable delay
slow slew rate = off
V
= 3.3 V
CCIO
Output buffer enable delay
slow slew rate = on
V
= 2.5 V or 3.3 V
CCIO
Output buffer disable delay
Register setup time
Register hold time
tXZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSU
0.7
0.4
0.8
1.2
1.1
0.5
0.8
1.2
1.6
0.9
1.1
1.4
tH
Register setup time of fast input
Register hold time of fast input
Register delay
tFSU
tFH
tRD
0.5
0.2
1.2
1.2
0.7
1.0
1.0
0.7
1.5
0.6
0.3
1.8
1.7
1.1
1.3
1.3
1.0
2.1
0.9
0.5
2.8
2.6
1.6
1.9
1.9
1.4
3.2
Combinatorial delay
Array clock delay
tCOMB
tIC
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
tEN
tGLOB
tPRE
tCLR
tPIA
tLPA
(2)
(4)
Low-power adder
36
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 20. EPM7032B Selectable I/O Standard Timing Adder Delays
Parameter
Notes (1)
I/O Standard
3.3 V TTL/CMOS
2.5 V TTL/CMOS
1.8 V TTL/CMOS
SSTL-2 Class I
SSTL-2 Class II
SSTL-3 Class I
SSTL-3 Class II
GTL+
Speed Grade
-5.0
Unit
-3.5
Min
-7.5
Max Min Max
Min Max
Input to (PIA)
0.0
0.0
0.0
0.0
0.3
0.3
0.2
0.2
0.5
0.5
0.4
1.2
1.3
1.2
0.9
0.0
1.3
1.2
0.9
–0.1
1.2
0.9
0.8
0.0
1.2
0.9
0.8
0.0
1.6
1.6
1.5
0.0
0.0
0.0
0.0
0.0
0.4
0.4
0.3
0.3
0.8
0.8
0.5
1.8
1.9
1.8
1.3
0.0
1.9
1.8
1.3
–0.1
1.8
1.3
1.1
0.0
1.8
1.3
1.1
0.0
2.3
2.3
2.1
0.0
0.0
0.0
0.0
0.0
0.6
0.6
0.4
0.4
1.1
1.1
0.8
2.6
2.8
2.6
1.9
0.0
2.8
2.6
1.9
–0.2
2.6
1.9
1.7
0.0
2.6
1.9
1.7
0.0
3.4
3.4
3.2
0.0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Altera Corporation
37
MAX 7000B Programmable Logic Device Data Sheet
Table 20. EPM7032B Selectable I/O Standard Timing Adder Delays
Notes (1)
I/O Standard
Parameter
Speed Grade
-5.0
Unit
-3.5
Min
-7.5
Max Min Max
Min Max
PCI
Input to PIA
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Notes to tables:
(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for
more information on switching waveforms.
(2) These values are specified for a PIA fan-out of all LABs.
(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(4) The t
parameter must be added to the t
, t
, t , t
, t
, t , and t parameters for macrocells
LPA
LAD LAC IC ACL CPPW EN
SEXP
running in low-power mode.
38
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 21. EPM7064B External Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-5
Unit
-3
-7
Min
Max
Min
Max
Min
Max
t
Input to non-registered
output
C1 = 35 pF (2)
3.5
5.0
7.5
ns
ns
PD1
PD2
t
I/O input to non-registered C1 = 35 pF (2)
output
3.5
5.0
7.5
t
t
t
Global clock setup time
Global clock hold time
(2)
(2)
2.1
0.0
1.0
3.0
0.0
1.0
4.5
0.0
1.5
ns
ns
ns
SU
H
Global clock setup time of
fast input
FSU
t
t
Global clock hold time of
fast input
1.0
2.0
1.0
2.5
1.0
3.0
ns
ns
FH
Global clock setup time of
fast input with zero hold
time
FZHSU
t
t
Global clock hold time of
fast input with zero hold
time
0.0
1.0
0.0
1.0
0.0
1.0
ns
ns
FZHH
CO1
Global clock to output
delay
C1 = 35 pF
2.4
3.6
3.4
5.1
5.0
7.6
t
t
t
t
t
t
t
t
Global clock high time
Global clock low time
Array clock setup time
Array clock hold time
1.5
1.5
0.9
0.2
1.0
1.5
1.5
1.5
2.0
2.0
1.3
0.3
1.0
2.0
2.0
2.0
3.0
3.0
1.9
0.6
1.0
3.0
3.0
3.0
ns
ns
ns
ns
ns
ns
ns
ns
CH
CL
(2)
(2)
ASU
AH
Array clock to output delay C1 = 35 pF (2)
Array clock high time
ACO1
ACH
ACL
CPPW
Array clock low time
Minimum pulse width for
clear and preset
t
f
t
f
Minimum global clock
period
(2)
3.3
3.3
4.7
4.7
7.0
7.0
ns
MHz
ns
CNT
Maximum internal global
clock frequency
(2), (3)
(2)
303.0
303.0
212.8
212.8
142.9
142.9
CNT
Minimum array clock
period
ACNT
ACNT
Maximum internal array
clock frequency
(2), (3)
MHz
Altera Corporation
39
MAX 7000B Programmable Logic Device Data Sheet
Table 22. EPM7064B Internal Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-5
Unit
-3
-7
Min Max Min Max Min Max
Input pad and buffer delay
I/O input pad and buffer delay
Fast input delay
tIN
0.3
0.3
0.9
1.0
0.5
0.5
1.3
1.5
0.7
0.7
2.0
1.5
ns
ns
ns
ns
tIO
tFIN
tFIND
Programmable delay adder for
fast input
Shared expander delay
Parallel expander delay
Logic array delay
tSEXP
tPEXP
tLAD
tLAC
tIOE
1.5
0.4
1.4
1.2
0.1
0.9
2.1
0.6
2.0
1.7
0.2
1.2
3.2
0.9
3.1
2.6
0.3
1.8
ns
ns
ns
ns
ns
ns
Logic control array delay
Internal output enable delay
Output buffer and pad delay
slow slew rate = off
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
tOD1
V
= 3.3 V
CCIO
Output buffer and pad delay
slow slew rate = on
tOD3
tZX1
tZX3
5.9
1.6
6.6
1.6
6.2
2.2
7.2
2.2
6.8
3.4
8.4
3.4
ns
ns
ns
V
= 2.5 V or 3.3 V
CCIO
Output buffer enable delay
slow slew rate = off
V
= 3.3 V
CCIO
Output buffer enable delay
slow slew rate = on
V
= 2.5 V or 3.3 V
CCIO
Output buffer disable delay
Register setup time
Register hold time
tXZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSU
0.7
0.4
0.8
1.2
1.1
0.5
0.8
1.2
1.6
0.9
1.1
1.4
tH
Register setup time of fast input
Register hold time of fast input
Register delay
tFSU
tFH
tRD
0.5
0.2
1.2
1.2
0.7
1.0
1.0
0.7
1.5
0.6
0.3
1.8
1.7
1.1
1.3
1.3
1.0
2.1
0.9
0.5
2.8
2.6
1.6
1.9
1.9
1.4
3.2
Combinatorial delay
Array clock delay
tCOMB
tIC
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
tEN
tGLOB
tPRE
tCLR
tPIA
tLPA
(2)
(4)
Low-power adder
40
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 23. EPM7064B Selectable I/O Standard Timing Adder Delays (Part 1 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-5
Unit
-3
-7
Min
Max Min Max
Min Max
3.3 V TTL/CMOS
Input to PIA
0.0
0.0
0.0
0.0
0.3
0.3
0.2
0.2
0.5
0.5
0.4
1.2
1.3
1.2
0.9
0.0
1.3
1.2
0.9
–0.1
1.2
0.9
0.8
0.0
1.2
0.9
0.8
0.0
1.6
1.6
1.5
0.0
0.0
0.0
0.0
0.0
0.4
0.4
0.3
0.3
0.7
0.7
0.6
1.7
1.9
1.7
1.3
0.0
1.9
1.7
1.3
–0.1
1.7
1.3
1.1
0.0
1.7
1.3
1.1
0.0
2.3
2.3
2.1
0.0
0.0
0.0
0.0
0.0
0.6
0.6
0.4
0.4
1.1
1.1
0.9
2.6
2.8
2.6
1.9
0.0
2.8
2.6
1.9
–0.2
2.6
1.9
1.7
0.0
2.6
1.9
1.7
0.0
3.4
3.4
3.2
0.0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
2.5 V TTL/CMOS
1.8 V TTL/CMOS
SSTL-2 Class I
SSTL-2 Class II
SSTL-3 Class I
SSTL-3 Class II
GTL+
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Altera Corporation
41
MAX 7000B Programmable Logic Device Data Sheet
Table 23. EPM7064B Selectable I/O Standard Timing Adder Delays (Part 2 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-5
Unit
-3
-7
Min
Max Min Max
Min Max
PCI
Input to PIA
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Notes to tables:
(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for
more information on switching waveforms.
(2) These values are specified for a PIA fan-out of all LABs.
(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(4) The t
parameter must be added to the t
, t
, t , t
, t
, t , and t parameters for macrocells
LPA
LAD LAC IC ACL CPPW EN
SEXP
running in low-power mode.
42
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 24. EPM7128B External Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-4
-10
Min
Max
Min
Max
Min
Max
t
Input to non-registered
output
C1 = 35 pF (2)
4.0
7.5
10.0
ns
ns
PD1
PD2
t
I/O input to non-registered C1 = 35 pF (2)
output
4.0
7.5
10.0
t
t
t
Global clock setup time
Global clock hold time
(2)
(2)
2.5
0.0
1.0
4.5
0.0
1.5
6.1
0.0
1.5
ns
ns
ns
SU
H
Global clock setup time of
fast input
FSU
t
t
Global clock hold time of
fast input
1.0
2.0
1.0
3.0
1.0
3.0
ns
ns
FH
Global clock setup time of
fast input with zero hold
time
FZHSU
t
t
Global clock hold time of
fast input with zero hold
time
0.0
1.0
0.0
1.0
0.0
1.0
ns
ns
FZHH
CO1
Global clock to output
delay
C1 = 35 pF
2.8
4.1
5.7
8.2
7.5
t
t
t
t
t
t
t
t
Global clock high time
Global clock low time
Array clock setup time
Array clock hold time
1.5
1.5
1.2
0.2
1.0
1.5
1.5
1.5
3.0
3.0
2.0
0.7
1.0
3.0
3.0
3.0
4.0
4.0
2.8
0.9
1.0
4.0
4.0
4.0
ns
ns
ns
ns
ns
ns
ns
ns
CH
CL
(2)
(2)
ASU
AH
Array clock to output delay C1 = 35 pF (2)
Array clock high time
10.8
ACO1
ACH
ACL
CPPW
Array clock low time
Minimum pulse width for
clear and preset
t
f
t
f
Minimum global clock
period
(2)
4.1
4.1
7.9
7.9
10.6
10.6
ns
MHz
ns
CNT
Maximum internal global
clock frequency
(2), (3)
(2)
243.9
243.9
126.6
126.6
94.3
94.3
CNT
Minimum array clock
period
ACNT
ACNT
Maximum internal array
clock frequency
(2), (3)
MHz
Altera Corporation
43
MAX 7000B Programmable Logic Device Data Sheet
Table 25. EPM7128B Internal Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-4
-10
Min Max Min Max Min Max
Input pad and buffer delay
I/O input pad and buffer delay
Fast input delay
tIN
0.3
0.3
1.3
1.0
0.6
0.6
2.9
1.5
0.8
0.8
3.7
1.5
ns
ns
ns
ns
tIO
tFIN
tFIND
Programmable delay adder for
fast input
Shared expander delay
Parallel expander delay
Logic array delay
tSEXP
tPEXP
tLAD
tLAC
tIOE
1.5
0.4
1.6
1.4
0.1
0.9
2.8
0.8
2.9
2.6
0.3
1.7
3.8
1.0
3.8
3.4
0.4
2.2
ns
ns
ns
ns
ns
ns
Logic control array delay
Internal output enable delay
Output buffer and pad delay
slow slew rate = off
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
tOD1
V
= 3.3 V
CCIO
Output buffer and pad delay
slow slew rate = on
tOD3
tZX1
tZX3
5.9
1.8
6.8
1.8
6.7
3.3
8.3
3.3
7.2
4.4
9.4
4.4
ns
ns
ns
V
= 2.5 V or 3.3 V
CCIO
Output buffer enable delay
slow slew rate = off
V
= 3.3 V
CCIO
Output buffer enable delay
slow slew rate = on
V
= 2.5 V or 3.3 V
CCIO
Output buffer disable delay
Register setup time
Register hold time
tXZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSU
1.0
0.4
0.8
1.2
1.9
0.8
0.9
1.6
2.6
1.1
0.9
1.6
tH
Register setup time of fast input
Register hold time of fast input
Register delay
tFSU
tFH
tRD
0.5
0.2
1.4
1.4
1.1
1.0
1.0
1.0
1.5
1.1
0.3
2.8
2.6
2.3
1.9
1.9
2.0
2.8
1.4
0.4
3.6
3.4
3.1
2.6
2.6
2.8
3.8
Combinatorial delay
Array clock delay
tCOMB
tIC
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
tEN
tGLOB
tPRE
tCLR
tPIA
tLPA
(2)
(4)
Low-power adder
44
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 26. EPM7128B Selectable I/O Standard Timing Adder Delays (Part 1 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-4
-10
Min
Max Min Max
Min Max
3.3 V TTL/CMOS
Input to PIA
0.0
0.0
0.0
0.0
0.3
0.3
0.2
0.2
0.5
0.5
0.4
1.2
1.4
1.2
1.0
0.0
1.4
1.2
1.0
–0.1
1.3
1.0
0.9
0.0
1.3
1.0
0.9
0.0
1.7
1.7
1.6
0.0
0.0
0.0
0.0
0.0
0.6
0.6
0.4
0.4
0.9
0.9
0.8
2.3
2.6
2.3
1.9
0.0
2.6
2.3
1.9
–0.2
2.4
1.9
1.7
0.0
2.4
1.9
1.7
0.0
3.2
3.2
3.0
0.0
0.0
0.0
0.0
0.0
0.8
0.8
0.5
0.5
1.3
1.3
1.0
3.0
3.5
3.0
2.5
0.0
3.5
3.0
2.5
–0.3
3.3
2.5
2.3
0.0
3.3
2.5
2.3
0.0
4.3
4.3
4.0
0.0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
2.5 V TTL/CMOS
1.8 V TTL/CMOS
SSTL-2 Class I
SSTL-2 Class II
SSTL-3 Class I
SSTL-3 Class II
GTL+
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Altera Corporation
45
MAX 7000B Programmable Logic Device Data Sheet
Table 26. EPM7128B Selectable I/O Standard Timing Adder Delays (Part 2 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-4
-10
Min
Max Min Max
Min Max
PCI
Input to PIA
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Notes to tables:
(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for
more information on switching waveforms.
(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.1 ns to the PIA timing value.
(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(4) The t
parameter must be added to the t
, t
, t , t
, t
, t , and t parameters for macrocells
LPA
LAD LAC IC ACL CPPW EN
SEXP
running in low-power mode.
46
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 27. EPM7256B External Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-5
-10
Min
Max
Min
Max
Min
Max
t
Input to non-registered
output
C1 = 35 pF (2)
5.0
7.5
10.0
ns
ns
PD1
t
I/O input to non-registered C1 = 35 pF (2)
output
5.0
7.5
10.0
PD2
t
t
t
Global clock setup time
Global clock hold time
(2)
(2)
3.3
0.0
1.0
4.8
0.0
1.5
6.6
0.0
1.5
ns
ns
ns
SU
H
Global clock setup time of
fast input
FSU
t
Global clock hold time for
fast input
1.0
2.5
1.0
3.0
1.0
3.0
ns
ns
FH
t
Global clock setup time of
fast input with zero hold
time
FZHSU
t
t
Global clock hold time of
fast input with zero hold
time
0.0
1.0
0.0
1.0
0.0
1.0
ns
ns
FZHH
Global clock to output
delay
C1 = 35 pF
3.3
5.2
5.1
7.9
6.7
CO1
t
t
t
t
t
t
t
t
Global clock high time
Global clock low time
Array clock setup time
Array clock hold time
2.0
2.0
1.4
0.4
1.0
2.0
2.0
2.0
3.0
3.0
2.0
0.8
1.0
3.0
3.0
3.0
4.0
4.0
2.8
1.0
1.0
4.0
4.0
4.0
ns
ns
ns
ns
ns
ns
ns
ns
CH
CL
(2)
(2)
ASU
AH
Array clock to output delay C1 = 35 pF (2)
Array clock high time
10.5
ACO1
ACH
ACL
CPPW
Array clock low time
Minimum pulse width for
clear and preset
t
f
t
f
Minimum global clock
period
(2)
5.3
5.3
7.9
7.9
10.6
10.6
ns
MHz
ns
CNT
Maximum internal global
clock frequency
(2), (3)
(2)
188.7
188.7
126.6
126.6
94.3
94.3
CNT
Minimum array clock
period
ACNT
ACNT
Maximum internal array
clock frequency
(2), (3)
MHz
Altera Corporation
47
MAX 7000B Programmable Logic Device Data Sheet
Table 28. EPM7256B Internal Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-5
-10
Min Max Min Max Min Max
Input pad and buffer delay
I/O input pad and buffer delay
Fast input delay
tIN
0.4
0.4
1.5
1.5
0.6
0.6
2.5
1.5
0.8
0.8
3.1
1.5
ns
ns
ns
ns
tIO
tFIN
tFIND
Programmable delay adder for
fast input
Shared expander delay
Parallel expander delay
Logic array delay
tSEXP
tPEXP
tLAD
tLAC
tIOE
1.5
0.4
1.7
1.5
0.1
0.9
2.3
0.6
2.5
2.2
0.2
1.4
3.0
0.8
3.3
2.9
0.3
1.9
ns
ns
ns
ns
ns
ns
Logic control array delay
Internal output enable delay
Output buffer and pad delay
slow slew rate = off
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
tOD1
V
= 3.3 V
CCIO
Output buffer and pad delay
slow slew rate = on
tOD3
tZX1
tZX3
5.9
2.2
7.2
2.2
6.4
3.3
8.3
3.3
6.9
4.5
9.5
4.5
ns
ns
ns
V
= 2.5 V or 3.3 V
CCIO
Output buffer enable delay
slow slew rate = off
V
= 3.3 V
CCIO
Output buffer enable delay
slow slew rate = on
V
= 2.5 V or 3.3 V
CCIO
Output buffer disable delay
Register setup time
Register hold time
tXZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSU
1.2
0.6
0.8
1.2
1.8
1.0
1.1
1.4
2.5
1.3
1.1
1.4
tH
Register setup time of fast input
Register hold time of fast input
Register delay
tFSU
tFH
tRD
0.7
0.3
1.5
1.5
1.3
1.0
1.0
1.7
2.0
1.0
0.4
2.3
2.2
2.1
1.6
1.6
2.6
3.0
1.3
0.5
3.0
2.9
2.7
2.1
2.1
3.3
4.0
Combinatorial delay
Array clock delay
tCOMB
tIC
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
tEN
tGLOB
tPRE
tCLR
tPIA
tLPA
(2)
(4)
Low-power adder
48
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 29. EPM7256B Selectable I/O Standard Timing Adder Delays (Part 1 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-5
-10
Min
Max Min Max
Min Max
3.3 V TTL/CMOS
Input to PIA
0.0
0.0
0.0
0.0
0.4
0.3
0.2
0.2
0.6
0.6
0.5
1.3
1.5
1.3
1.1
0.0
1.5
1.3
1.1
–0.1
1.4
1.1
1.0
0.0
1.4
1.1
1.0
0.0
1.8
1.8
1.7
0.0
0.0
0.0
0.0
0.0
0.6
0.5
0.3
0.3
0.9
0.9
0.8
2.0
2.3
2.0
1.7
0.0
2.3
2.0
1.7
–0.2
2.1
1.7
1.5
0.0
2.1
1.7
1.5
0.0
2.7
2.7
2.6
0.0
0.0
0.0
0.0
0.0
0.8
0.6
0.4
0.4
1.2
1.2
1.0
2.6
3.0
2.6
2.2
0.0
3.0
2.6
2.2
–0.2
2.8
2.2
2.0
0.0
2.8
2.2
2.0
0.0
3.6
3.6
3.4
0.0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
2.5 V TTL/CMOS
1.8 V TTL/CMOS
SSTL-2 Class I
SSTL-2 Class II
SSTL-3 Class I
SSTL-3 Class II
GTL+
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Altera Corporation
49
MAX 7000B Programmable Logic Device Data Sheet
Table 29. EPM7256B Selectable I/O Standard Timing Adder Delays (Part 2 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-5
-10
Min
Max Min Max
Min Max
PCI
Input to PIA
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Notes to tables:
(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for
more information on switching waveforms.
(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.1 ns to the PIA timing value.
(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(4) The t
parameter must be added to the t
, t
, t , t
, t
, t , and t parameters for macrocells
LPA
LAD LAC IC ACL CPPW EN
SEXP
running in low-power mode.
50
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 30. EPM7512B External Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-5
-10
Min
Max
Min
Max
Min
Max
t
Input to non-registered
output
C1 = 35 pF (2)
5.5
7.5
10.0
ns
ns
PD1
PD2
t
I/O input to non-registered C1 = 35 pF (2)
output
5.5
7.5
10.0
t
t
t
Global clock setup time
Global clock hold time
(2)
(2)
3.6
0.0
1.0
4.9
0.0
1.5
6.5
0.0
1.5
ns
ns
ns
SU
H
Global clock setup time of
fast input
FSU
t
t
Global clock hold time of
fast input
1.0
2.5
1.0
3.0
1.0
3.0
ns
ns
FH
Global clock setup time of
fast input with zero hold
time
FZHSU
t
t
Global clock hold time of
fast input with zero hold
time
0.0
1.0
0.0
1.0
0.0
1.0
ns
ns
FZHH
CO1
Global clock to output
delay
C1 = 35 pF
3.7
5.9
5.0
8.0
6.7
t
t
t
t
t
t
t
t
Global clock high time
Global clock low time
Array clock setup time
Array clock hold time
3.0
3.0
1.4
0.5
1.0
3.0
3.0
3.0
3.0
3.0
1.9
0.6
1.0
3.0
3.0
3.0
4.0
4.0
2.5
0.8
1.0
4.0
4.0
4.0
ns
ns
ns
ns
ns
ns
ns
ns
CH
CL
(2)
(2)
ASU
AH
Array clock to output delay C1 = 35 pF (2)
Array clock high time
10.7
ACO1
ACH
ACL
CPPW
Array clock low time
Minimum pulse width for
clear and preset
t
f
t
f
Minimum global clock
period
(2)
6.1
6.1
8.4
8.4
11.1
11.1
ns
MHz
ns
CNT
Maximum internal global
clock frequency
(2), (3)
(2)
163.9
163.9
119.0
119.0
90.1
90.1
CNT
Minimum array clock
period
ACNT
ACNT
Maximum internal array
clock frequency
(2), (3)
MHz
Altera Corporation
51
MAX 7000B Programmable Logic Device Data Sheet
Table 31. EPM7512B Internal Timing Parameters
Note (1)
Symbol
Parameter
Conditions
Speed Grade
-7
Unit
-5
-10
Min Max Min Max Min Max
Input pad and buffer delay
I/O input pad and buffer delay
Fast input delay
tIN
0.3
0.3
2.2
1.5
0.3
0.3
3.2
1.5
0.5
0.5
4.0
1.5
ns
ns
ns
ns
tIO
tFIN
tFIND
Programmable delay adder for
fast input
Shared expander delay
Parallel expander delay
Logic array delay
tSEXP
tPEXP
tLAD
tLAC
tIOE
1.5
0.4
1.7
1.5
0.1
0.9
2.1
0.5
2.3
2.0
0.2
1.2
2.7
0.7
3.0
2.6
0.2
1.6
ns
ns
ns
ns
ns
ns
Logic control array delay
Internal output enable delay
Output buffer and pad delay
slow slew rate = off
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 35 pF
C1 = 5 pF
tOD1
V
= 3.3 V
CCIO
Output buffer and pad delay
slow slew rate = on
tOD3
tZX1
tZX3
5.9
2.8
7.8
2.8
6.2
3.8
8.8
3.8
6.6
5.0
ns
ns
ns
V
= 2.5 V or 3.3 V
CCIO
Output buffer enable delay
slow slew rate = off
V
= 3.3 V
CCIO
Output buffer enable delay
slow slew rate = on
10.0
5.0
V
= 2.5 V or 3.3 V
CCIO
Output buffer disable delay
Register setup time
Register hold time
tXZ
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSU
1.5
0.4
0.8
1.2
2.0
0.5
1.1
1.4
2.6
0.7
1.1
1.4
tH
Register setup time of fast input
Register hold time of fast input
Register delay
tFSU
tFH
tRD
0.5
0.2
1.8
1.5
2.0
1.0
1.0
2.4
2.0
0.7
0.3
2.4
2.0
2.8
1.4
1.4
3.4
2.7
1.0
0.4
3.1
2.6
3.6
1.9
1.9
4.5
3.6
Combinatorial delay
Array clock delay
tCOMB
tIC
Register enable time
Global control delay
Register preset time
Register clear time
PIA delay
tEN
tGLOB
tPRE
tCLR
tPIA
tLPA
(2)
(4)
Low-power adder
52
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Table 32. EPM7512B Selectable I/O Standard Timing Adder Delays (Part 1 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-5
-10
Min
Max Min Max
Min Max
3.3 V TTL/CMOS
Input to PIA
0.0
0.0
0.0
0.0
0.4
0.3
0.2
0.2
0.7
0.6
0.5
1.3
1.5
1.4
1.1
0.0
1.5
1.4
1.1
–0.1
1.4
1.2
1.0
0.0
1.4
1.2
1.0
0.0
1.8
1.9
1.8
0.0
0.0
0.0
0.0
0.0
0.5
0.4
0.3
0.3
1.0
0.8
0.6
1.8
2.0
1.9
1.5
0.0
2.0
1.9
1.5
–0.1
1.9
1.6
1.4
0.0
1.9
1.6
1.4
0.0
2.5
2.6
2.5
0.0
0.0
0.0
0.0
0.0
0.7
0.5
0.3
0.3
1.3
1.0
0.8
2.3
2.7
2.5
2.0
0.0
2.7
2.5
2.0
–0.2
2.5
2.2
1.8
0.0
2.5
2.2
1.8
0.0
3.3
3.5
3.3
0.0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
2.5 V TTL/CMOS
1.8 V TTL/CMOS
SSTL-2 Class I
SSTL-2 Class II
SSTL-3 Class I
SSTL-3 Class II
GTL+
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Input to PIA
Input to global clock and clear
Input to fast input register
All outputs
Altera Corporation
53
MAX 7000B Programmable Logic Device Data Sheet
Table 32. EPM7512B Selectable I/O Standard Timing Adder Delays (Part 2 of 2)
Note (1)
I/O Standard
Parameter
Speed Grade
-7
Unit
-5
-10
Min
Max Min Max
Min Max
PCI
Input to PIA
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ns
ns
ns
ns
Input to global clock and clear
Input to fast input register
All outputs
Notes to tables:
(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for
more information on switching waveforms.
(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.12 ns to the PIA timing value.
(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(4) The t
parameter must be added to the t
, t
, t , t
, t
, t , and t
parameters for macrocells
LPA
LAD LAC IC ACL CPPW EN
SEXP
running in low-power mode.
Supply power (P) versus frequency (fMAX, in MHz) for MAX 7000B
devices is calculated with the following equation:
Power
Consumption
P = PINT + PIO = ICCINT × VCC + PIO
The PIO value, which depends on the device output load characteristics
and switching frequency, can be calculated using the guidelines given in
Application Note 74 (Evaluating Power for Altera Devices).
54
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
The ICCINT value depends on the switching frequency and the application
logic. The ICCINT value is calculated with the following equation:
ICCINT
=
(A × MCTON) + [B × (MCDEV – MCTON)] + (C × MCUSED × fMAX × togLC
)
The parameters in this equation are:
MCTON
=
Number of macrocells with the Turbo BitTM option turned
on, as reported in the MAX+PLUS II Report File (.rpt)
Number of macrocells in the device
Total number of macrocells in the design, as reported in
the Report File
MCDEV
MCUSED
=
=
fMAX
togLC
=
=
Highest clock frequency to the device
Average percentage of logic cells toggling at each clock
(typically 12.5%)
A, B, C
=
Constants, shown in Table 33
Table 33. MAX 7000B ICC Equation Constants
Device
A
B
C
EPM7032B
EPM7064B
EPM7128B
EPM7256B
EPM7512B
0.91
0.91
0.91
0.91
0.91
0.54
0.54
0.54
0.54
0.54
0.010
0.012
0.016
0.017
0.019
This calculation provides an ICC estimate based on typical conditions
using a pattern of a 16-bit, loadable, enabled, up/down counter in each
LAB with no output load. Actual ICC should be verified during operation
because this measurement is sensitive to the actual pattern in the device
and the environmental operating conditions.
Altera Corporation
55
MAX 7000B Programmable Logic Device Data Sheet
Figure 15. ICC vs. Frequency for EPM7032B Devices
45
40
35
30
25
20
15
10
5
EPM7032B
285.7 MHz
VCC = 2.5 V
Room Temperature
High Speed
Typical ICC
Active (mA)
153.8 MHz
Low Power
0
50
100
150
200
250
300
Frequency (MHz)
Figure 16. ICC vs. Frequency for EPM7064B Devices
90
EPM7064B
285.7 MHz
VCC = 2.5 V
Room Temperature
80
70
60
50
40
30
High Speed
Typical ICC
Active (mA)
153.8 MHz
Low Power
20
10
0
50
100
150
200
250
300
Frequency (MHz)
56
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 17. ICC vs. Frequency for EPM7128B Devices
220
200
180
160
EPM7128B
VCC = 2.5 V
Room Temperature
238.1 MHz
140
120
High Speed
Typical ICC
Active (mA)
100
80
129.9 MHz
Low Power
60
40
20
0
50
100
150
200
250
Frequency (MHz)
Figure 18. ICC vs. Frequency for EPM7256B Devices
400
EPM7256B
VCC = 2.5 V
Room Temperature
350
300
188.7 MHz
High Speed
250
Typical ICC
Active (mA)
200
150
107.5 MHz
Low Power
100
50
0
50
100
Frequency (MHz)
150
200
Altera Corporation
57
MAX 7000B Programmable Logic Device Data Sheet
Figure 19. ICC vs. Frequency for EPM7512B Devices
700
EPM7512B
163.9 MHz
VCC = 2.5 V
Room Temperature
600
500
400
High Speed
99.0 MHz
Typical ICC
Active (mA)
300
200
Low Power
100
0
20
40
60
80
100
120
140
160
180
Frequency (MHz)
58
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
See the Altera web site (http://www.altera.com) or the Altera Digital
Library for pin-out information.
Device
Pin-Outs
Figures 20 through 29 show the package pin-out diagrams for
MAX 7000B devices.
Figure 20. 44-Pin PLCC/TQFP Package Pin-Out Diagram
Package outlines not drawn to scale.
Pin 34
Pin 1
6
5
4
3
2
1 44 43 42 41 40
7
39
38
37
36
35
34
33
32
31
30
29
I/O
I/O/TDI
I/O
I/O/TDI
I/O
I/O
8
I/O/TDO
I/O
I/O/TDO
9
I/O
I/O
I/O
10
11
12
13
14
15
16
17
I/O
GND
I/O
GND
I/O
I/O
VCC
I/O
VCC
I/O
I/O
EPM7032B
EPM7064B
EPM7032B
EPM7064B
I/O
I/O
I/O/TMS
I/O
I/O
I/O/TMS
I/O
I/O/TCK
I/O
I/O/TCK
I/O
VCC
I/O
GND
I/O
VCC
I/O
I/O
GND
I/O
I/O
18 19 20 21 22 23 24 25 26 27 28
Pin 12
Pin 23
44-Pin PLCC
44-Pin TQFP
Altera Corporation
59
MAX 7000B Programmable Logic Device Data Sheet
Figure 21. 48-Pin VTQFP Package Pin-Out Diagram
Package outlines not drawn to scale.
48 47 46 45 44 43 42 41 40 39 38 37
36
35
34
33
32
31
30
29
28
27
26
25
I/O
1
N/C
I/O/TDI
I/O
I/O/TDO
I/O
2
3
I/O
I/O
4
VCCIO2
I/O
GNDIO
I/O / VREFA
I/O
5
6
EPM7032B
EPM7064B
I/O
7
I/O/TCK
I/O / VREFB
GNDIO
I/O
I/O/TMS
I/O
8
9
VCCIO1
I/O
10
11
12
I/O
I/O
13 14 15 16 17 18 19 20 21 22 23 24
48-Pin VTQFP
Figure 22. 49-Pin Ultra FineLine BGA Package Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball
Pad Corner
Indicates
location of
Ball A1
A
B
C
D
E
F
EPM7032B
EPM7064B
EPM7128B
G
7
6
5
4
3
2
1
60
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 23. 100-Pin TQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Pin 1
Pin 76
EPM7064B
EPM7128B
EPM7256B
Pin 26
Pin 51
Figure 24. 100-Pin FineLine BGA Package Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball
Pad Corner
Indicates
location of
Ball A1
A
B
C
D
E
F
G
H
EPM7064B
EPM7128B
EPM7256B
J
K
10
9
8
7
6
5
4
3
2
1
Altera Corporation
61
MAX 7000B Programmable Logic Device Data Sheet
Figure 25. 144-Pin TQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Indicates location
of Pin 1
Pin 1
Pin 109
EPM7128B
EPM7256B
EPM7512B
Pin 37
Pin 73
Figure 26. 169-Pin Ultra FineLine BGA Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball
Pad Corner
Indicates
Location of
Ball A1
A
B
C
D
E
F
G
H
J
K
EPM7128AE
L
M
N
13 12 11 10
9
8
7
6
5
4
3
2
1
62
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 27. 208-Pin PQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Pin 1
Pin 157
EPM7256B
EPM7512B
Pin 53
Pin 105
Altera Corporation
63
MAX 7000B Programmable Logic Device Data Sheet
Figure 28. 256-Pin BGA Package Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball
Pad Corner
Indicates
Location of
Ball A1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
EPM7512B
U
V
W
Y
20 19 18 17 16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
64
Altera Corporation
MAX 7000B Programmable Logic Device Data Sheet
Figure 29. 256-Pin FineLine BGA Package Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball
Pad Corner
A
Indicates
Location of
Ball A1
B
C
D
E
F
G
H
J
K
EPM7128B
EPM7256B
EPM7512B
L
M
N
P
R
T
16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
The information contained in the MAX 7000B Programmable Logic Device
Family Data Sheet version 3.5 supersedes information published in
previous versions.
Revision
History
Version 3.5
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.5:
■
Updated Figure 28.
Version 3.4
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.4:
■
Updated text in the “Power Sequencing & Hot-Socketing” section.
Altera Corporation
65
MAX 7000B Programmable Logic Device Data Sheet
Version 3.3
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.3:
■
■
Updated Table 3.
Added Tables 4 through 6.
Version 3.2
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.2:
■
Updated Note (10) and added ambient temperature (TA) information
to Table 15.
Version 3.1
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.1:
■
■
Updated VIH and VIL specifications in Table 16.
Updated leakage current conditions in Table 16.
Version 3.0
The following changes were made to the MAX 7000B Programmable Logic
Device Family Data Sheet version 3.0:
■
■
■
Updated timing numbers in Table 1.
Updated Table 16.
Updated timing in Tables 18, 19, 21, 22, 24, 25, 27, 28, 30, and 31.
101 Innovation Drive
San Jose, CA 95134
(408) 544-7000
http://www.altera.com
Applications Hotline:
(800) 800-EPLD
Customer Marketing:
(408) 544-7104
Literature Services:
lit_req@altera.com
Copyright © 2003 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the
stylized Altera logo, specific device designations, and all other words and logos that are identified as
trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera
Corporation in the U.S. and other countries. All other product or service names are the property of their
respective holders. Altera products are protected under numerous U.S. and foreign patents and pending
applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to
current specifications in accordance with Altera's standard warranty, but reserves the right
to make changes to any products and services at any time without notice. Altera assumes no
responsibility or liability arising out of the application or use of any information, product, or
service described herein except as expressly agreed to in writing by Altera Corporation.
Altera customers are advised to obtain the latest version of device specifications before
relying on any published information and before placing orders for products or services.
66
Altera Corporation
Printed on Recycled Paper.
Literature
Buy On-Line
Licensing
Download
Entire Site
|
|
|
|
|
|
|
Buy On-Line
Home
Products
Support
End Markets
Technology Center
Education & Events
Corporate
EPM7032B
Results For:
10 part numbers found and 4 obsolete part numbers found
MAX 7000B Device Family (2.5V, SSTL, GTL+)
MAX 7000B Datasheet
Part Number Format
MAX 7000 Literature
Buying Altera Devices
Part Number
Device
Pin & Package Temperature Speeds
Options
EPM7032BTC44-3
EPM7032BTC44-3N
EPM7032BTC44-5
EPM7032BTC44-5N
EPM7032BTC44-7
EPM7032BTC44-7N
EPM7032B 44 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-3, -5, -7 N: Lead-free
EPM7032BTI44-5
EPM7032B 44 pin TQFP
Pinout
Industrial
-5
None
( -40 to 105°C)
EPM7032BUC49-3 EPM7032B 49 pin UBGA
Commercial
( 0 to 90°C)
-3, -5, -7 None
EPM7032BUC49-5
EPM7032BUC49-7
Pinout
Your search for
found 4 obsolete part numbers.
EPM7032B
Obsolete Part Numbers
Part Number Format
Buying Altera Devices
Part Number
Last Order Date Last Ship Date Replacement
Notes
EPM7032BLC44-3
06-30-2006
12-30-2006
Call Factory
PDN 0510
EPM7032BLC44-5
06-30-2006
12-30-2006
Call Factory
PDN 0510
EPM7032BLC44-7
06-30-2006
12-30-2006
06-30-2007
Call Factory
Call Factory
PDN 0510
PDN 0518
EPM7032BUC49-3A 12-21-2006
Search
EPM7032B
Advanced Search
Please Give Us Feedback
Sign Up for E-mail Updates
Home | Products | Support | End Markets | Technology Center | Education & Events | Corporate | Buy On-Line
Contact Us | Site Help | Site Map | Privacy | Legal Notice
Copyright © 1995-2006 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA
Literature
Buy On-Line
Licensing
Download
Entire Site
|
|
|
|
|
|
|
Buy On-Line
Home
Products
Support
End Markets
Technology Center
Education & Events
Corporate
EPM7064B
Results For:
13 part numbers found and 6 obsolete part numbers found
MAX 7000B Device Family (2.5V, SSTL, GTL+)
MAX 7000B Datasheet
Part Number Format
MAX 7000 Literature
Buying Altera Devices
Part Number
Device
Pin & Package Temperature Speeds
Options
EPM7064BFC100-3
EPM7064BFC100-5
EPM7064BFC100-7
EPM7064B 100 pin FBGA Commercial
-3, -5, -7 None
Pinout
( 0 to 90°C)
EPM7064BTC44-3
EPM7064BTC44-5
EPM7064BTC44-7
EPM7064BTC44-7N
EPM7064B 44 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-3, -5, -7 N: Lead-free
-3, -5, -7 N: Lead-free
EPM7064BTC100-3
EPM7064BTC100-3N
EPM7064BTC100-5
EPM7064BTC100-5N
EPM7064BTC100-7
EPM7064B 100 pin TQFP
Pinout
Commercial
( 0 to 90°C)
EPM7064BTI44-5
EPM7064B 44 pin TQFP
Pinout
Industrial
-5
None
( -40 to 105°C)
Your search for
found 6 obsolete part numbers.
EPM7064B
Obsolete Part Numbers
Part Number Format
Buying Altera Devices
Replacement Notes
Part Number
Last Order Date Last Ship Date
EPM7064BTI100-5 06-30-2006
EPM7064BTI100-7 06-30-2006
EPM7064BTI44-7 06-30-2006
EPM7064BUC49-3 06-30-2006
EPM7064BUC49-5 06-30-2006
EPM7064BUC49-7 06-30-2006
12-30-2006
12-30-2006
12-30-2006
12-30-2006
12-30-2006
12-30-2006
EPM7064BTC100-3 PDN 0510
EPM7064BTC100-5 PDN 0510
EPM7064BTC44-5 PDN 0510
Call Factory
Call Factory
Call Factory
PDN 0510
PDN 0510
PDN 0510
Search
EPM7064B
Advanced Search
Please Give Us Feedback
Sign Up for E-mail Updates
Home | Products | Support | End Markets | Technology Center | Education & Events | Corporate | Buy On-Line
Contact Us | Site Help | Site Map | Privacy | Legal Notice
Copyright © 1995-2006 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA
Literature
Buy On-Line
Licensing
Download
Entire Site
|
|
|
|
|
|
|
Buy On-Line
Home
Products
Support
End Markets
Technology Center
Education & Events
Corporate
EPM7128B
Results For:
19 part numbers found and 1 obsolete part number found
MAX 7000B Device Family (2.5V, SSTL, GTL+)
MAX 7000B Datasheet
Part Number Format
MAX 7000 Literature
Buying Altera Devices
Part Number
Device
Pin & Package Temperature Speeds
Options
EPM7128BFC100-4
EPM7128BFC100-4N
EPM7128BFC100-7
EPM7128BFC100-10
EPM7128BFC100-10N
EPM7128B 100 pin FBGA Commercial
-4, -7, -10 N: Lead-free
Pinout ( 0 to 90°C)
EPM7128BFC256-4
EPM7128BFC256-7
EPM7128BFC256-10
EPM7128B 256 pin FBGA Commercial
Pinout ( 0 to 90°C)
-4, -7, -10 None
EPM7128BFI100-7
EPM7128B 100 pin FBGA Industrial
-7
-7
None
None
Pinout
( -40 to 105°C)
EPM7128BFI256-7
EPM7128B 256 pin FBGA Industrial
Pinout
( -40 to 105°C)
EPM7128BTC100-4
EPM7128BTC100-4N
EPM7128BTC100-7
EPM7128BTC100-7N
EPM7128BTC100-10
EPM7128B 100 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-4, -7, -10 N: Lead-free
EPM7128BTC144-4
EPM7128BTC144-7
EPM7128BTC144-10
EPM7128BTC144-10N
EPM7128B 144 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-4, -7, -10 N: Lead-free
Your search for
found 1 obsolete part number.
EPM7128B
Obsolete Part Numbers
Part Number Format
Buying Altera Devices
Part Number
Last Order Date Last Ship Date
12-30-2006
Replacement
Notes
EPM7128BTI100-7 06-30-2006
EPM7128BTC100-4 PDN 0510
Search
EPM7128B
Advanced Search
Please Give Us Feedback
Sign Up for E-mail Updates
Home | Products | Support | End Markets | Technology Center | Education & Events | Corporate | Buy On-Line
Contact Us | Site Help | Site Map | Privacy | Legal Notice
Copyright © 1995-2006 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA
Literature
Buy On-Line
Licensing
Download
Entire Site
|
|
|
|
|
|
|
Buy On-Line
Home
Products
Support
End Markets
Technology Center
Education & Events
Corporate
EPM7256B
Results For:
27 part numbers found and 2 obsolete part numbers found
MAX 7000B Device Family (2.5V, SSTL, GTL+)
MAX 7000B Datasheet
Part Number Format
MAX 7000 Literature
Buying Altera Devices
Part Number
Device
Pin & Package Temperature Speeds
Options
EPM7256BFC256-5
EPM7256BFC256-7
EPM7256BFC256-7N
EPM7256BFC256-10
EPM7256BFC256-10N
EPM7256B 256 pin FBGA Commercial
-5, -7, -10 N: Lead-free
Pinout ( 0 to 90°C)
EPM7256BFI256-7
EPM7256B 256 pin FBGA Industrial
-7
None
Pinout
( -40 to 105°C)
EPM7256BQC208-5
EPM7256BQC208-7
EPM7256BQC208-10
EPM7256B 208 pin PQFP Commercial
-5, -7, -10 None
Pinout
( 0 to 90°C)
EPM7256BTC100-5
EPM7256BTC100-5N
EPM7256BTC100-7
EPM7256BTC100-7N
EPM7256BTC100-10
EPM7256BTC100-10N
EPM7256B 100 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-5, -7, -10 N: Lead-free
EPM7256BTC144-5
EPM7256BTC144-5N
EPM7256BTC144-7
EPM7256BTC144-7N
EPM7256BTC144-10
EPM7256BTC144-10N
EPM7256B 144 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-5, -7, -10 N: Lead-free
EPM7256BTI100-7N
EPM7256B 100 pin TQFP
Industrial
-7
N: Lead-free
Pinout
( -40 to 105°C)
EPM7256BUC169-5
EPM7256BUC169-7
EPM7256BUC169-7N
EPM7256BUC169-10
EPM7256BUC169-10N
EPM7256B 169 pin UBGA Commercial
-5, -7, -10 N: Lead-free
Pinout ( 0 to 90°C)
Your search for
found 2 obsolete part numbers.
EPM7256B
Obsolete Part Numbers
Part Number Format
Buying Altera Devices
Part Number
Last Order Date Last Ship Date
Replacement
Notes
EPM7256BQI208-7 06-30-2006
12-30-2006
EPM7256BQC208-5 PDN 0510
EPM7256BTI100-7 06-30-2006
12-30-2006
EPM7256BTC100-5 PDN 0510
Search
EPM7256B
Advanced Search
Please Give Us Feedback
Sign Up for E-mail Updates
Home | Products | Support | End Markets | Technology Center | Education & Events | Corporate | Buy On-Line
Contact Us | Site Help | Site Map | Privacy | Legal Notice
Copyright © 1995-2006 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA
Literature
Buy On-Line
Licensing
Download
Entire Site
|
|
|
|
|
|
|
Buy On-Line
Home
Products
Support
End Markets
Technology Center
Education & Events
Corporate
EPM7512B
Results For:
19 part numbers found and 1 obsolete part number found
MAX 7000B Device Family (2.5V, SSTL, GTL+)
MAX 7000B Datasheet
Part Number Format
MAX 7000 Literature
Buying Altera Devices
Part Number
Device
Pin & Package Temperature Speeds
Options
EPM7512BBC256-5
EPM7512BBC256-7
EPM7512BBC256-10
EPM7512B 256 pin BGA
Pinout
Commercial
( 0 to 90°C)
-5, -7, -10 None
EPM7512BFC256-5
EPM7512BFC256-5N
EPM7512BFC256-7
EPM7512BFC256-7N
EPM7512BFC256-10
EPM7512B 256 pin FBGA Commercial
Pinout ( 0 to 90°C)
-5, -7, -10 N: Lead-free
EPM7512BFI256-7
EPM7512B 256 pin FBGA Industrial
-7
None
Pinout
( -40 to 105°C)
EPM7512BQC208-5
EPM7512BQC208-7
EPM7512BQC208-10
EPM7512B 208 pin PQFP Commercial
-5, -7, -10 None
Pinout
( 0 to 90°C)
EPM7512BTC144-5
EPM7512BTC144-7
EPM7512BTC144-10
EPM7512B 144 pin TQFP
Pinout
Commercial
( 0 to 90°C)
-5, -7, -10 None
EPM7512BUC169-5
EPM7512BUC169-7
EPM7512BUC169-7N
EPM7512BUC169-10
EPM7512B 169 pin UBGA Commercial
Pinout ( 0 to 90°C)
-5, -7, -10 N: Lead-free
Your search for
found 1 obsolete part number.
EPM7512B
Obsolete Part Numbers
Part Number Format
Buying Altera Devices
Part Number
Last Order Date Last Ship Date
Replacement
Notes
EPM7512BFI256-10 06-30-2006
12-30-2006
EPM7512BFC256-7 PDN 0510
Search
EPM7512B
Advanced Search
Please Give Us Feedback
Sign Up for E-mail Updates
Home | Products | Support | End Markets | Technology Center | Education & Events | Corporate | Buy On-Line
Contact Us | Site Help | Site Map | Privacy | Legal Notice
Copyright © 1995-2006 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA
相关型号:
©2020 ICPDF网 联系我们和版权申明