NUC8I7HVK [INTEL]
Intel NUC Kit;
| 型号： | NUC8I7HVK |
| 厂家： | 
INTEL |
| 描述： | Intel NUC Kit |
| 文件： | 总63页 (文件大小：2099K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Intel® NUC Kit NUC8i7HV
Technical Product Specification
Regulatory Model: NUC8HV
October 2019
Order Number: J89400-009
Intel NUC Kit NUC8i7HV may contain design defects or errors known as errata that may cause the product to deviate from published specifications.
Current characterized errata, if any, are documented in Intel NUC Kit NUC8i7HV Specification Update.
Revision History
Revision
001
Revision History
Date
First release of the Intel NUC Kit NUC8i7HV Technical Product Specification
March 2018
April 2018
002
Spec change
003
Specification clarification
Spec change
May 2018
004
July 2018
005
Spec change
August 2018
September 2018
February 2019
August 2019
October 2019
006
Spec change
007
Spec change
008
Spec change
009
Specification clarification
Disclaimer
This product specification applies to only the standard Intel NUC Kit with BIOS identifier HNSKLi70.86A.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR
IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.
EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO
LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR
USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR
ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL
INJURY OR DEATH MAY OCCUR.
All Intel NUC Kits are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for
installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC
or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc.
may not be supported without further evaluation by Intel.
Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property
rights that relate to the presented subject matter. The furnishing of documents and other materials and information does
not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or
other intellectual property rights.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or
“undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or
incompatibilities arising from future changes to them.
Intel processor numbers are not a measure of performance. Processor numbers differentiate features within each
processor family, not across different processor families: Go to:
Learn About Intel® Processor Numbers
Intel NUC may contain design defects or errors known as errata, which may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product
order.
Intel, the Intel logo, Intel NUC and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2019 Intel Corporation. All rights reserved.
Kit Identification Information
Basic Intel® NUC Kit NUC8i7HV Identification Information
SA Revision
J71485 – 502
J71485 – 502
J71485 – 502
J71485 – 502
J71485 – 502
Power Cord
Original BIOS Revision
HNKBLi70.86A.0029
HNKBLi70.86A.0029
HNKBLi70.86A.0029
HNKBLi70.86A.0029
HNKBLi70.86A.0029
Notes
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
No Power Cord
US Power Cord
EU Power Cord
UK Power Cord
AU Power Cord
Notes:
1. The SA number is found on a bottom side of the chassis.
2. The Intel® Core™ i7-8809G processor is used on this SA revision consisting of the following component:
3. For product revisions check intel QDMS - https://qdms.intel.com/Portal/SearchPCNDataBase.aspx
Device
Stepping
S-Spec Numbers
Intel Core i7-8809G
B0
SR3RL
Product Identification Information
Intel® NUC Products NUC8i7HVK{x} Identification Information
Differentiating Features
Product Name
Intel® NUC
Board
Kit with Power Adapter
NUC8i7HVK
NUC8i7HVB
J71485 – xxx
Kit with Power Adapter, 1TB Intel® M.2 NVME SSD,
16GB DDR4-2400 SDRAM,
NUC8i7HVKVA{x}
Microsoft Windows 10 Home
Kit with Power Adapter, 512GB Intel® M.2 NVME SSD,
8GB DDR4-2400 SDRAM,
NUC8i7HVKVAW
Microsoft Windows 10 Home
Specification Changes or Clarifications
The table below indicates the Specification Changes or Specification Clarifications that apply to
the Intel NUC Board NUC8i7HV.
iii
Intel NUC Kit NUC8i7HV Technical Product Specification
Specification Changes or Clarifications
Date
Type of Change
Description of Changes or Clarifications
Changed TBD86A to HNKBLi70.86A in the section “Overview of BIOS
Features” > “Introduction”
April 2018
Specification
change
Changed hyperlink http://intel.com/TBD to
https://downloadcenter.intel.com/download/27641 in the section “Overview
of BIOS Features” > “System LED Functionality”
May 2018
July 2018
Specification
clarification
Corrected reference to Table 3 in “DisplayPort 1.2 Multi-Stream Transport
Daisy-Chaining” section
Spec change
Added SATA Power section to 2.2.3.1
Added 1.15 – Intel Platform Security Technologies
Added 1.16 – Thunderbolt 3
August 2018
Spec change
Added “Product Identification Information” table
Added text to Wireless row of table in Feature Summary section:
“Pre-installed M.2 module”
September 2018 Spec change
February 2019
August 2019
Spec change
Spec change
Added section 2.4.1 - Weights
Corrected environmental table
Added QDMS link for product change notification information.
Clarified Board vs System environmental specifications.
October 2019
Specification
clarification
Errata
Current characterized errata, if any, are documented in a separate Specification Update. See
http://www.intel.com/content/www/us/en/nuc/overview.html for the latest documentation.
iv
Preface
This Technical Product Specification (TPS) specifies the layout, components, connectors, power
and environmental requirements, and the BIOS for Intel® NUC Kit NUC8i7HV.
NOTE
In this document, the use of “kit” will refer to Intel® NUC Kit NUC8i7HV.
Intended Audience
The TPS is intended to provide detailed, technical information about Intel® NUC Kit NUC8i7HV
and its components to the vendors, system integrators, and other engineers and technicians who
need this level of information. It is specifically not intended for general audiences.
What This Document Contains
Chapter
Description
1
2
3
4
5
A description of the hardware used on Intel NUC Kit NUC8i7HV
A map of the resources of the Intel NUC Kit NUC8i7HV
The features supported by the BIOS Setup program
A description of the BIOS error messages, beep codes, and POST codes
Regulatory compliance and battery disposal information
Typographical Conventions
This section contains information about the conventions used in this specification. Not all of
these symbols and abbreviations appear in all specifications of this type.
Notes, Cautions, and Warnings
NOTE
Notes call attention to important information.
CAUTION
Cautions are included to help you avoid damaging hardware or losing data.
v
Intel NUC Kit NUC8i7HV Technical Product Specification
Other Common Notation
#
Used after a signal name to identify an active-low signal (such as USBP0#)
GB
Gigabyte (1,073,741,824 bytes)
Gigabytes per second
GB/s
Gb/s
KB
Gigabits per second
Kilobyte (1024 bytes)
Kb
Kilobit (1024 bits)
kb/s
MB
1000 bits per second
Megabyte (1,048,576 bytes)
Megabytes per second
MB/s
Mb
Megabit (1,048,576 bits)
Mb/s
TDP
Xxh
x.x V
*
Megabits per second
Thermal Design Power
An address or data value ending with a lowercase h indicates a hexadecimal value.
Volts. Voltages are DC unless otherwise specified.
This symbol is used to indicate third-party brands and names that are the property of their respective
owners.
vi
Contents
Revision History...............................................................................................................ii
Disclaimer .................................................................................................................................................................. ii
Kit Identification Information ........................................................................................................................... iii
Product Identification Information................................................................................................................. iii
Errata...........................................................................................................................................................................iv
Preface ...............................................................................................................................v
Intended Audience................................................................................................................................................. v
What This Document Contains......................................................................................................................... v
Typographical Conventions ............................................................................................................................... v
Contents ..........................................................................................................................vii
1 Product Description ............................................................................................... 13
1.1 Overview ......................................................................................................................................................13
1.1.1
1.1.2
Feature Summary ..................................................................................................................13
Block Diagram.........................................................................................................................15
1.2 Online Support..........................................................................................................................................16
1.3 Processor.....................................................................................................................................................16
1.4 Platform Controller Hub (PCH)...........................................................................................................16
1.4.1
1.5 System Memory........................................................................................................................................17
1.5.1 Memory Configurations ......................................................................................................18
1.6 Graphics Capabilities ..............................................................................................................................19
Direct Media Interface (DMI)..............................................................................................16
1.6.1
1.6.2
Intel Integrated Graphics....................................................................................................19
Radeon RX Vega M................................................................................................................19
1.7 USB.................................................................................................................................................................23
1.8 Storage Interface......................................................................................................................................24
1.8.1
1.8.2
AHCI Mode................................................................................................................................24
Intel® Rapid Storage Technology / SATA RAID .........................................................24
1.9 SDXC Card Reader ...................................................................................................................................24
1.10 Real-Time Clock........................................................................................................................................25
1.11 Audio 25
1.11.1 Audio Software.......................................................................................................................26
1.12 LAN
26
1.12.1 Intel® Gigabit Ethernet Controller I219-LM ................................................................26
1.12.2 Intel® Gigabit Ethernet Controller I210-AT.................................................................26
1.12.3 LAN Software...........................................................................................................................27
1.12.4 RJ-45 LAN Connector with Integrated LEDs..............................................................28
1.12.5 Wireless Network Module..................................................................................................29
1.13 Hardware Management Subsystem .................................................................................................29
vii
1.13.1 Hardware Monitoring...........................................................................................................29
1.13.2 Fan Monitoring........................................................................................................................29
1.13.3 Thermal Solution...................................................................................................................30
1.14 Power Management ................................................................................................................................31
1.14.1 ACPI.............................................................................................................................................31
1.14.2 Hardware Support.................................................................................................................33
1.15 Intel Platform Security Technologies ..............................................................................................35
1.15.1 Intel® Virtualization Technology......................................................................................35
1.15.2 Intel® Platform Trust Technology...................................................................................35
1.16 Thunderbolt 3............................................................................................................................................36
2 Technical Reference............................................................................................... 37
2.1 Memory Resources..................................................................................................................................37
2.1.1
Addressable Memory...........................................................................................................37
2.2 Connectors and Headers.......................................................................................................................37
2.2.1
2.2.2
2.2.3
Front Panel Connectors......................................................................................................38
Back Panel Connectors .......................................................................................................40
USB and I/O Headers ...........................................................................................................41
2.3 VESA Bracket..............................................................................................................................................50
2.4 Mechanical Considerations..................................................................................................................51
2.4.1
Weights......................................................................................................................................51
2.5 Power Supply.............................................................................................................................................52
2.5.1
2.5.2
Power Supply Connector ...................................................................................................53
Fan Header Current Capability.........................................................................................53
2.6 Reliability .....................................................................................................................................................53
2.7 Environmental ...........................................................................................................................................54
3 Overview of BIOS Features................................................................................... 55
3.1 Introduction................................................................................................................................................55
3.2 BIOS Flash Memory Organization .....................................................................................................55
3.3 System Management BIOS (SMBIOS)..............................................................................................55
3.4 Legacy USB Support ...............................................................................................................................56
3.5 BIOS Updates.............................................................................................................................................56
3.5.1
Language Support.................................................................................................................57
3.6 BIOS Recovery...........................................................................................................................................57
3.7 Boot Options..............................................................................................................................................57
3.7.1
3.7.2
3.7.3
3.7.4
Network Boot...........................................................................................................................57
Booting Without Attached Devices................................................................................58
Changing the Default Boot Device During POST......................................................58
Power Button Menu..............................................................................................................59
3.8 Hard Disk Drive Password Security Feature..................................................................................60
3.9 BIOS Security Features ..........................................................................................................................60
3.10 System LED Functionality.....................................................................................................................62
viii
Contents
4 Error Messages and Blink Codes......................................................................... 63
4.1 Front-panel Power LED Blink Codes................................................................................................63
4.2 BIOS Error Messages...............................................................................................................................63
ix
Figures
Figure 1. Block Diagram...........................................................................................................................................15
Figure 2. Memory Channel and SO-DIMM Configuration..........................................................................18
Figure 3. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out ...............................................................................25
Figure 4. LAN Connector LED Locations...........................................................................................................28
Figure 5. Thermal Solution and Fan Header...................................................................................................30
Figure 6. Front Panel Layout .................................................................................................................................38
Figure 7. Back Panel Layout...................................................................................................................................40
Figure 8. Headers and Connectors (Top) .........................................................................................................41
Figure 9. USB 3.0 Internal Header (1.25 mm Pitch) .....................................................................................43
Figure 10. Connection Diagram for the Internal IO Common Header (1.25 mm Pitch)................44
Figure 11. Additional Headers and Connectors............................................................................................45
Figure 12. BIOS Security Jumper ........................................................................................................................46
Figure 13. Kit Dimensions.......................................................................................................................................49
Figure 14. Install VESA Bracket............................................................................................................................50
Figure 15. VESA Bracket Dimensions ................................................................................................................51
Figure 16. Power Adapter and Plugs Included with the Kit......................................................................52
Tables
Table 1. Feature Summary.....................................................................................................................................13
Table 2. Supported DDR4/-RS Non-ECC SO-DIMM Module Configurations....................................17
Table 3. Mini DisplayPort and Type C DisplayPort Multi-Streaming Resolutions ..........................21
Table 4. Multiple Display Configuration Maximum Resolutions ............................................................22
Table 5. Audio Formats Supported by the HDMI and Mini DisplayPort Interfaces........................23
Table 6. LAN Connector LED States...................................................................................................................28
Table 7. Effects of Pressing the Power Switch...............................................................................................31
Table 8. Power States and Targeted System Power ...................................................................................32
Table 9. Wake-up Devices and Events..............................................................................................................33
Table 10. Components Shown in Figure 6......................................................................................................38
Table 11. Components Shown in Figure 7......................................................................................................40
Table 12. Headers and Connectors Shown in Figure 8..............................................................................41
Table 13. Auxiliary SATA power connector pin out.....................................................................................41
Table 14. Headers and Connectors Shown in Figure 11...........................................................................45
Table 15. BIOS Security Jumper Settings........................................................................................................47
Table 16. M.2 2280 Module (key type M) Connectors................................................................................47
Table 18. Select Weights ........................................................................................................................................51
Table 17. Dual Fan Header Current Capability..............................................................................................53
Table 19. Environmental Specifications...........................................................................................................54
Table 20. Acceptable Drives/Media Types for BIOS Recovery ...............................................................57
Table 21. Boot Device Menu Options................................................................................................................58
Table 22. Master Key and User Hard Drive Password Functions...........................................................60
Table 23. Supervisor and User Password Functions...................................................................................61
Table 24. Default RGB LED Locations and Behaviors.................................................................................62
x
Contents
Table 25. Front-panel Power LED Blink Codes .............................................................................................63
Table 26. BIOS Error Messages............................................................................................................................63
xi
1
Product Description
1.1
Overview
1.1.1
Feature Summary
Table 1 summarizes the major features of Intel® NUC Kit NUC8i7HV.
Table 1. Feature Summary
8.66 inches by 5.51 inches by 1.57 inches (220 millimeters by 140 millimeters by
40 millimeters)
Form Factor
•
A soldered-down 8th generation Intel® Core™ i7-8809G quad-core processor with up to a
maximum 45 W TDP
Processor
― Intel® HD Graphics 630
― Integrated memory controller
PCH
Intel® HM175 Platform Controller Hub
•
Two 260-pin DDR4 SDRAM Small Outline Dual Inline Memory Module (SO-DIMM)
sockets
Memory
•
•
•
•
•
Support for DDR4 2400 MHz SO-DIMMs
Support for 4 Gb and 8 Gb memory technology
Support for up to 32 GB of system memory with two SO-DIMMs
Support for non-ECC memory
Support for 1.2 V and 1.35 V low voltage JEDEC memory only
Note: 2 Gb memory technology (SDRAM Density) is not compatible
•
•
Integrated graphics support for processors with Intel® Graphics Technology
Discrete graphics support by Radeon RX Vega M GH
Graphics
― Two Full Size High Definition Multimedia Interface* (HDMI*) Front and Back panel
connectors
― Two Mini DisplayPort* back panel connectors
― Two Type C back panel connectors
•
Intel® High Definition (Intel® HD) Audio via the HDMI v2.0, Mini DisplayPort 1.2 and Type C
interfaces through the processor/Discrete GPU
Audio
•
•
Radeon High Definition Audio
Realtek HD Audio via a stereo microphone/headphone 3.5 mm jack on the front panel
and 3.5mm combination speaker/TOSLINK jack on the back panel
Storage
Two SATA 6.0 Gb/s or Gen3 PCIe X4 AHCI, NVMe ports are reserved for M.2 storage
modules supporting M.2 2242 and M.2 2280 (key type M) modules
Note: Supports key type M (PCI Express* x1/x2/x4 and SATA)
continued
13
Table 1. Feature Summary (continued)
•
USB 3.1 Gen 2 Ports:
Peripheral Interfaces
― One Type-A port is implemented with an external front panel connector (blue), one
Type C port is implemented with an external front panel connnector
•
USB 3.0 Ports:
― One port is implemented with an external front panel connector (yellow charging
capable)
― Four ports are implemented with external back panel connectors (blue)
― Two ports are implemented via an internal header (blue)
― 1 port implemented via the external back panel Type C connector
USB 2.0 ports:
•
― Two ports via an internal common IO header (white)
― One port is reserved for the M.2 2230 Wireless module
Consumer Infrared (CIR)
•
•
Two M.2 connectors supporting M.2 2242 (1 slot) and M.2 2280 (key type M both slots)
modules
Expansion Capabilities
BIOS
•
•
•
One Full Size SDXC Slot
Intel® BIOS resident in the Serial Peripheral Interface (SPI) Flash device
Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and
System Management BIOS (SMBIOS)
•
•
Suspend to RAM support
Instantly Available PC
Technology
Wake on PCI Express, LAN, front panel, CIR, and USB ports
Gigabit (10/100/1000 Mb/s) LAN subsystem using the Intel® Gigabit Ethernet Controller
I219-LM
LAN
Gigabit (10/100/1000 Mb/s) LAN subsystem using the Intel® Gigabit Ethernet Controller
I210-at
Hardware Monitor
Subsystem
Hardware monitoring subsystem, based on a ITE IT8987VG including:
•
•
•
•
•
Voltage sense to detect out of range power supply voltages
Thermal sense to detect out of range thermal values
Two processor fan headers
Fan sense input used to monitor fan activity
Fan speed control
Intel® Dual Band Wireless-AC 8265
Wireless
•
•
•
802.11ac, Dual Band, Wi-Fi + Bluetooth 4.2
Supports Intel® Wireless Display 6.0 (WiDi)
Pre-installed M.2 module
14
Product Description
1.1.2
Block Diagram
Figure 1 is a block diagram of the major functional areas of Intel NUC Kit NUC8i7HV.
Figure 1. Block Diagram
15
1.2
1.3
1.4
Online Support
To find information about…
Intel NUC Kit NUC8i7HV
Intel NUC Kit Support
Visit this World Wide Web site:
http://www.intel.com/NUC
http://www.intel.com/NUCSupport
Available configurations for Intel NUC Kit NUC8i7HV http://ark.intel.com
BIOS and driver updates
Tested memory
http://downloadcenter.intel.com
http://www.intel.com/NUCSupport
http://www.intel.com/NUCSupport
http://ark.intel.com
Integration information
Processor datasheet
Processor
A soldered-down 8th generation Intel® Core™ i7-8809G quad-core processor with up to a
maximum 45 W TDP.
•
•
Intel HD Graphics 630
Integrated memory controller
NOTE
There are specific requirements for providing power to the processor. Refer to Section 2.5.1 on
page 51 for information on power supply requirements.
Platform Controller Hub (PCH)
A soldered-down Intel HM175 Platform Controller Hub with Direct Media Interface (DMI)
interconnect provides interfaces to the processor and the USB, SATA, LAN, PCI Express interfaces.
The HM175 is a centralized controller for the kit’s I/O paths.
1.4.1
Direct Media Interface (DMI)
Direct Media Interface (DMI) is the chip-to-chip connection between the processor and PCH. This
high-speed interface integrates advanced priority-based servicing allowing for concurrent traffic
and true isochronous transfer capabilities.
16
Product Description
1.5
System Memory
The kit has two 260-pin SO-DIMM sockets and supports the following memory features:
•
•
•
•
1.2V / 1.35V DDR4 SDRAM SO-DIMMs with gold plated contacts
Two independent memory channels with interleaved mode support
Unbuffered, single-sided or double-sided SO-DIMMs
32 GB maximum total system memory. Refer to Section 2.1.1 on page 37 for information on
the total amount of addressable memory.
•
•
•
•
Minimum recommended total system memory: 4096 MB
Non-ECC SO-DIMMs
Serial Presence Detect
DDR4 2400 MHz SDRAM SO-DIMMs
NOTE
To be fully compliant with all applicable DDR SDRAM memory specifications, the kit should be
populated with SO-DIMMs that support the Serial Presence Detect (SPD) data structure. This
allows the BIOS to read the SPD data and program the chipset to accurately configure memory
settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to
correctly configure the memory settings, but performance and reliability may be impacted or the
SO-DIMMs may not function under the determined frequency.
Table 2 lists the supported SO-DIMM configurations.
Table 2. Supported DDR4/-RS Non-ECC SO-DIMM Module Configurations
# of
Banks
Inside
DRAM
Raw Card DIMM
DRAM Device
Technology
DRAM
Organization
# of DRAM
Devices
# of
Ranks
# of Row/Col
Address Bits
Page
Size
Version
Capacity
A
4GB
8GB
8GB
16GB
2GB
4GB
8GB
16GB
4Gb
8Gb
4Gb
8Gb
4Gb
8Gb
4Gb
8Gb
512M x 8
1024M x 8
512M x 8
1024M x 8
256M x 16
512M x 16
512M x 8
1024M x 8
8
1
1
2
2
1
1
2
2
15/10
16/10
15/10
16/10
15/10
16/10
15/10
16/10
16
16
16
16
8
8K
8K
8K
8K
8K
8K
8K
8K
A
B
B
C
C
E
E
8
16
16
4
4
8
16
16
16
16
For information about…
Refer to:
http://www.intel.com/NUCSupport
Tested Memory
17
1.5.1
Memory Configurations
The processor supports the following types of memory organization:
•
Dual channel (Interleaved) mode. This mode offers the highest throughput for real world
applications. Dual channel mode is enabled when the installed memory capacities of both
SO-DIMM channels are equal. Technology and device width can vary from one channel to the
other but the installed memory capacity for each channel must be equal. If different speed
SO-DIMMs are used between channels, the slowest memory timing will be used.
Single channel (Asymmetric) mode. This mode is equivalent to single channel bandwidth
operation for real world applications. This mode is used when only a single SO-DIMM is
installed or the memory capacities are unequal. Technology and device width can vary from
one channel to the other. If different speed SO-DIMMs are used between channels, the
slowest memory timing will be used.
•
For information about…
Refer to:
Memory Configuration Examples
http://www.intel.com/NUCSupport
Figure 2 illustrates the memory channel and SO-DIMM configuration.
Figure 2. Memory Channel and SO-DIMM Configuration
18
Product Description
1.6
Graphics Capabilities
The kit supports graphics computing through Intel® HD™ Graphics 630.
1.6.1
Intel Integrated Graphics
The kit supports integrated graphics processing via the processor.
1.6.1.1
Intel® High Definition (Intel® HD) Graphics
The Intel HD graphics controller features the following:
•
3D Features
― DirectX* 12.1 support
― OpenGL* 4.4 support
― OpenCL* 2.1, OpenCL 2.0, OpenCL 1.2 support
•
•
Video:
Next Generation Intel® Clear Video Technology HD support is a collection of video playback
and enhancement features that improve the end user’s viewing experience
Encode/transcode HD content
DirectX* Video Acceleration (DXVA) support for accelerating video processing
Full AVC/VC1/MPEG2/HEVC HW Encode/Decode
•
•
•
•
Intel HD Graphics with Advanced Hardware Video Transcoding (Intel® Quick Sync Video)
*The graphics outputs of the NUC8i7HV are not physically connected to the HD Graphics 630.
NOTE
Intel Quick Sync Video is enabled by an appropriate software application.
1.6.2
Radeon RX Vega M
The kit supports graphics processing via discrete on package Radeon RX Vega M GH graphics
processor.
1.6.2.1
Radeon™ RX Vega M GH Graphics
The Radeon RX Vega M GH Graphics controller features the following:
•
3D Features
― DirectX* 12 (Direct3D feature level 12.0 support)
― OpenGL* 4.5 support
― OpenCL* 2.0 support
― Vulkan 1.0
Decode:
•
•
•
•
HEVC Main Profile@level 5.1
HEVC Main10 Profile@level 5.1
H.264 Constrained Baseline Profile@level 5.2
H.264 Main Profile@level 5.2
19
•
•
•
•
•
•
•
H.264 High Profile@level 5.2
H.264 Stereo High Profile@level 5.2
VC1 Simple & Main Profile@High Level(VLD)
VC1 Advanced Profile@level 3(VLD)
MPEG2 Main Profile@High level(IDCT/VLD)
MPEG4 Part 2 Advanced Simple Profile@level 5
MJPEG 1080p@60fps
Encode:
•
•
•
•
H.264 Constrained Baseline Profile@level 5.2
H.264 Main Profile@level 5.2
H.264 High Profile@level 5.2
HEVC user program up to Main Profile@level 6.2 for offline encode; HEVC Main Profile@level
5.1 in real time
1.6.2.2
Video Memory Allocation
Intel® Dynamic Video Memory Technology (DVMT) is a method for dynamically allocating system
memory for use as graphics memory to balance 2D/3D graphics and system performance. If your
computer is configured to use DVMT, graphics memory is allocated based on system
requirements and application demands (up to the configured maximum amount). When memory
is no longer needed by an application, the dynamically allocated portion of memory is returned to
the operating system for other uses.
1.6.2.3
High Definition Multimedia Interface* (HDMI*)
The HDMI ports support standard, enhanced, or high definition video, plus multi-channel digital
audio on a single cable. The ports are compatible with all ATSC and DVB HDTV standards and
supports eight full range channels at 24-bit/192 kHz audio of lossless audio formats. The
maximum supported resolution is 4096 x 2160 @ 60 Hz, 24 bpp. The HDMI ports are compliant
with the HDMI 2.0b specification.
For information about
Refer to
HDMI technology
http://www.hdmi.org
1.6.2.4
DisplayPort* via Mini DisplayPort and Type C
DisplayPort is a digital communication interface that utilizes differential signaling to achieve a
high bandwidth bus interface designed to support connections between PCs and monitors,
projectors, and TV displays. DisplayPort is suitable for display connections between consumer
electronics devices such as high definition optical disc players, set top boxes, and TV displays.
The Mini DisplayPort and Type C connectors are compliant with the DisplayPort 1.2 specification
and have a maximum supported resolution of 4096 x 2160 @ 60Hz 24bpp.
DisplayPort output supports Multi-Stream Transport (MST) which allows for multiple
independent video streams (daisy-chain connection with multiple monitors) over a single
DisplayPort. This will require the use of displays that support DisplayPort 1.2 specification and
allow for this feature.
20
Product Description
For information about
Refer to
http://www.displayport.org
DisplayPort technology
1.6.2.4.1
DisplayPort 1.2 Multi-Stream Transport Daisy-Chaining
Error! Reference source not found. lists the maximum resolutions available when using
DisplayPort 1.2 Multi-Stream Transport.
Table 3. Mini DisplayPort and Type C DisplayPort Multi-Streaming Resolutions
DisplayPort Usage Models
3 Monitors
Monitor 1
Monitor 2
Monitor 3
1920 x 1200 @ 60 Hz
2560 x 1600 @ 60 Hz
1920 x 1080 @ 60 Hz
1920 x 1200 @ 60 Hz
2560 x 1600 @ 60 Hz
1920 x 1080 @ 60 Hz
1920 x 1200 @ 60 Hz
2 Monitors
3 Monitors
1920 x 1080 @ 60 Hz
(with DisplayPort 1.2 hub)
21
1.6.2.5
Multiple DisplayPort, Type C and HDMI Configurations
Multiple Mini DisplayPort, Type C, and HDMI configurations feature the following:
•
•
Six independent displays with 4K support
― Two Mini DisplayPort, Two HDMI and Two Type C (rear Thunderbolt 3)
Eyefinity Display
Table 4. Multiple Display Configuration Maximum Resolutions
Single Display HDMI
4096 x 2160 @ 60 Hz
Dual Display HDMI
4096 x 2160 @ 60 Hz
Single Display Mini DisplayPort
4096 x 2160 @ 60 Hz
Single DisplayPort (rear Type C)
4096 x 2160 @ 60 Hz
Dual Display Mini DisplayPort
5120 x 2880 @ 60 Hz **
Dual DisplayPort (Rear Type C)
5120 x 2880 @ 60 Hz **
Triple Display – Any Combination of
Quadruple Display – Any Combination
Quintuple Display – Any Combination
Available Ports
of Available Ports*
of Available Ports*
4096 x 2160 @ 60 Hz (Type C)
4096 x 2160 @ 60 Hz (Mini DisplayPort)
4096 x 2160 @ 60Hz (HDMI)
4096 x 2160 @ 60 Hz (Type C)
4096 x 2160 @ 60 Hz (Mini DisplayPort)
4096 x 2160 @ 60Hz (HDMI)
4096 x 2160 @ 60 Hz (Type C)
4096 x 2160 @ 60 Hz (Mini DisplayPort)
4096 x 2160 @ 60Hz (HDMI)
Sextuple Display – Any Combination of
Available Ports*
4096 x 2160 @ 30 Hz (Type C)
4096 x 2160 @ 30 Hz (Mini DisplayPort)
4096 x 2160 @ 30Hz (HDMI)
*Note* Number of Displays can be influenced by default DPM states of the Radeon RX Vega M GH GPU.
**Note** Dual DisplayPort 5120 x 2800 @ 60 Hz refers to dual port monitors, and further requires 2 DisplayPort
connections to enumerate at that resolution.
For information about
Refer to
Multiple display maximum
resolutions
https://www-
ssl.intel.com/content/www/us/en/processors/core/CoreTechnicalResources.html
1.6.2.6
High-bandwidth Digital Content Protection (HDCP)
HDCP is the technology for protecting high definition content against unauthorized copy or
interception between a source (computer, digital set top boxes, etc.) and the sink (panels,
monitor, and TVs). The PCH supports HDCP 1.4 and HDCP 2.2 for content protection over wired
displays using the Mini DisplayPort and HDMI 2.0. The Thunderbolt Type C based DisplayPort
configuration will support up to HDCP1.4.
22
Product Description
1.6.2.7
Integrated Audio Provided by the HDMI and Mini DisplayPort
Interfaces
The HDMI and Mini DisplayPort interfaces from the GPU support audio. The processor supports
two High Definition audio streams on two digital ports simultaneously.
Table 5 shows the specific audio technologies supported by the GPU.
Table 5. Audio Formats Supported by the HDMI and Mini DisplayPort Interfaces
Audio Formats
HDMI Mini DisplayPort or Thunderbolt 3
AC3 – Dolby* Digital
Dolby Digital Plus
DTS-HD*
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
LPCM, 192 kHz/24 bit, 8 channel
Dolby True HD, DTS-HD Master Audio* (Lossless Blu-ray Disc
Audio Format)
1.7
USB
The USB port arrangement is as follows:
•
USB 3.0 ports (maximum current is 900 mA for each blue port, 1.5 A for the yellow charging
port):
― Two ports are implemented with external front panel connectors (one blue and one yellow
charging capable)
― Four ports are implemented with external back panel connectors (blue)
― Two ports are implmented with an internal header (blue)
― Two ports are implemented with the external black panel Type C connectors
All the USB 3.0 ports are super-speed, high-speed, full-speed, and low-speed capable.
•
USB 2.0 ports (maximum current is 500 mA for each port of the white header (1 A total):
― Two ports via internal common IO header (white)
― One port is reserved for the M.2 2230 Wireless module
All the USB 2.0 ports are high-speed, full-speed, and low-speed capable.
NOTE
Computer systems that have an unshielded cable attached to a USB port may not meet FCC
Class B requirements, even if no device is attached to the cable. Use a shielded cable that meets
the requirements for full-speed devices.
NOTE
The yellow USB charging port can be set in the BIOS to “Charging Only.” However this affects only
USB 2.0 devices and transfers and does not affect USB 3.0 devices and transfers.
23
For information about
Refer to
The location of the USB connectors on the back panel
The location of the front panel USB headers
Figure 7, page 40
Figure 6, page 38
1.8
Storage Interface
The kit provides the following storage interface options via 2 M.2 2242 and M.2 2280 (key type M)
connectors:
•
SATA 6.0 Gb/s ports are reserved for the M.2 storage modules supporting M.2 2242 and
M.2 2280 (key type M) modules
― The PCH provides independent SATA ports with a theoretical maximum transfer rate of
6 Gb/s. A point-to-point interface is used for host to device connections.
•
Gen 3 PCIe X4 AHCI, NVMe ports are reserved for the M.2 storage modules supporting
M.2 2242 and M.2 2280 (key type M) modules
1.8.1
AHCI Mode
The kit supports AHCI storage mode.
NOTE
In order to use AHCI mode, AHCI must be enabled in the BIOS. Microsoft* Windows* 10 includes
the necessary AHCI drivers without the need to install separate AHCI drivers during the operating
system installation process; however, it is always good practice to update the AHCI drivers to the
latest available by Intel.
1.8.2
Intel® Rapid Storage Technology / SATA RAID
The PCH supports Intel® Rapid Storage Technology, providing both AHCI and integrated RAID
functionality. The RAID capability provides high-performance RAID 0 and 1 functionality on all
SATA ports. Other RAID features include hot spare support and SMART alerting. Software
components include an Option ROM for pre-boot configuration and boot functionality, a
Microsoft Windows compatible driver, and a user interface for configuration and management of
the RAID capability of the PCH.
NOTE
In order to use supported RAID features, you must first enable RAID in the BIOS.
1.9
SDXC Card Reader
The kit has a standard Secure Digital (SD) card reader that supports the Secure Digital eXtended
Capacity (SDXC) format, 3.01 specification with UHS-I support. SD Card sizes supported from
8GB to 128GB.
24
Product Description
1.10 Real-Time Clock
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the kit is not
plugged into a wall socket, the battery has an estimated life of three years. When the kit is
plugged in, the standby current from the power supply extends the life of the battery. The clock
is accurate to 13 minutes/year at 25 ºC with 3.3 VSB applied via the power supply 5 V STBY rail.
NOTE
If the battery and AC power fail, date and time values will be reset and the user will be notified
during the POST.
When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS
RAM (for example, the date and time) might not be accurate. Replace the battery with an
equivalent one. Figure 12 on page 40 shows the location of the battery.
1.11 Audio
The integrated Realtek ALC700 audio subsystem supports the following features:
•
•
•
Digital microphone array (DMICS) connectors (internal)
Analog line-out/Analog Headphone/Analog Microphone (front panel jack)
Analog stereo line-out/TOSLINK out (back panel jack)
― Analog Speakers only (Stereo)
― SPDIF optical output formats up to compressed 5.1/7.1
•
•
•
Support for 44.1 kHz/48 kHz/96 kHz/192 kHz sample rates on all analog outputs
Support for 44.1 kHz/48 kHz/96 kHz sample rates on all analog inputs
Front Panel Audio Jack Support (see Figure 3 for 3.5 mm audio jack pin out):
― Speakers only (Stereo)
― Headphones only (Stereo)
― Microphone only (mono)
― Combo Headphone (Stereo)/Microphone (mono)
Pin Number
Pin Name
Tip
Ring
Ring
Sleeve
Description
1
2
3
4
Left Audio Out
Right Audio Out
Common/Ground
Audio In/MIC
Figure 3. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out
NOTE
The analog circuit of the front panel audio connector is designed to power headphones or
amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.
25
1.11.1
Audio Software
Audio software and drivers are available from Intel’s World Wide Web site.
For information about
Refer to
Obtaining Audio software and drivers
http://downloadcenter.intel.com
1.12 LAN
The onboard LAN consists of the following:
•
•
•
Intel Gigabit Ethernet Controller I219-LM (10/100/1000 Mb/s)
Intel Gigabit Ethernet Controller I210-AT (10/100/1000 Mb/s)
RJ-45 LAN connectors with integrated status LEDs
Additional features of the LAN subsystem include:
•
•
•
CSMA/CD protocol engine
LAN connect interface between the Processor and the LAN controller
Power management capabilities
― ACPI technology support
― LAN wake capabilities
•
LAN subsystem software
1.12.1
Intel® Gigabit Ethernet Controller I219-LM
The Intel Gigabit Ethernet Controller I219-LM supports the following features:
•
•
•
•
Compliant with the 1 Gb/s Ethernet 802.3, 802.3u, 802.3z, 802.3ab specifications
Multi-speed operation: 10/100/1000 Mb/s
Full-duplex operation at 10/100/1000 Mb/s; Half-duplex operation at 10/100 Mb/s
Flow control support compliant with the 802.3X specification as well as the specific operation
of asymmetrical flow control defined by 802.3z
•
•
VLAN support compliant with the 802.1q specification
Supports Jumbo Frames (up to 9 kB)
― IEEE 1588 supports (Precision Time Protocol)
•
MAC address filters: perfect match unicast filters, multicast hash filtering, broadcast filter, and
promiscuous mode
1.12.2
Intel® Gigabit Ethernet Controller I210-AT
The Intel Gigabit Ethernet Controller I210-at supports the following features:
•
•
•
•
Compliant with the 1 Gb/s Ethernet 802.3, 802.3u, 802.3z, 802.3ab specifications
Multi-speed operation: 10/100/1000 Mb/s
Full-duplex operation at 10/100/1000 Mb/s; Half-duplex operation at 10/100 Mb/s
Flow control support compliant with the 802.3X specification as well as the specific operation
of asymmetrical flow control defined by 802.3z
•
Supports Jumbo Frames (up to 9 kB)
― IEEE 1588 supports (Precision Time Protocol)
26
Product Description
•
MAC address filters: perfect match unicast filters, multicast hash filtering, broadcast filter, and
promiscuous mode
1.12.3
LAN Software
LAN software and drivers are available from Intel’s World Wide Web site.
For information about
Refer to
Obtaining LAN software and drivers
http://downloadcenter.intel.com
27
1.12.4
RJ-45 LAN Connector with Integrated LEDs
Two LEDs are built into the RJ-45 LAN connector (shown in Figure 4).
Item
Description
A
B
C
D
Link LED (Green)
Data Rate LED (Green/Yellow)
Link LED (Green)
Data Rate LED (Green/Yellow)
Figure 4. LAN Connector LED Locations
Table 6 describes the LED states when the board is powered up and the LAN subsystem is
operating.
Table 6. LAN Connector LED States
LED
LED Color
LED State
Off
Condition
LAN link is not established.
LAN link is established.
Link
Green
On
Blinking
Off
LAN activity is occurring.
10 Mb/s data rate is selected.
100 Mb/s data rate is selected.
1000 Mb/s data rate is selected.
Data Rate
Green/Yellow
Green
Yellow
28
Product Description
1.12.5
Wireless Network Module
The Intel Dual Band Wireless-AC 8265 module provides hi-speed wireless connectivity provided
with the following capabilities:
•
Compliant IEEE 802.11abgn, 802.11ac, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w
specifications
•
•
•
•
•
•
•
•
Maximum bandwidth of 867 Mbps
Dual Mode Bluetooth* 4.2
OS certified with : Microsoft Windows 10, Linux* (most features not available on Linux)
Wi-Fi Direct* for peer to peer device connections
Wi-Fi Miracast Source
Intel® Wireless Display 6.0
Wi-Fi Direct for peer to peer device connections
Authentication: WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM,
EAP-AKA
•
Encryption: 64-bit and 128-bit WEP, AES-CCMP, TKIP, WPA2, AES-CCMP
For information about
Obtaining WLAN software and drivers
Full Specifications
Refer to
http://downloadcenter.intel.com
http://intel.com/wireless
1.13 Hardware Management Subsystem
The hardware management features enable the board to be compatible with the Wired for
Management (WfM) specification. The kit has several hardware management features, including
thermal and voltage monitoring.
For information about
Refer to
Wired for Management (WfM) Specification
www.intel.com/design/archives/wfm/
1.13.1
Hardware Monitoring
The hardware monitoring and fan control subsystem is based on an ITE IT8987VG/BX, which
supports the following:
•
•
•
•
•
•
Processor and system ambient temperature monitoring
Chassis fan speed monitoring
Voltage monitoring of +5 V, +3.3 V, Memory Vcc (V_SM), +Vccp,
SMBus interface
Storage activity monitoring
Network activity monitoring
1.13.2
Fan Monitoring
Fan monitoring can be implemented using third-party software.
29
1.13.3
Thermal Solution
Figure 5 shows the location of the fan headers used for the thermal solution.
Figure 5. Thermal Solution and Fan Header
30
Product Description
1.14 Power Management
Power management is implemented at several levels, including:
•
•
Software support through Advanced Configuration and Power Interface (ACPI)
Hardware support:
― Power Input
― Instantly Available PC technology
― LAN wake capabilities
― Wake from USB
― WAKE# signal wake-up support
― Wake from S5
― Wake from CIR
1.14.1
ACPI
ACPI gives the operating system direct control over the power management and Plug and Play
functions of a computer. The use of ACPI with this kit requires an operating system that provides
full ACPI support. ACPI features include:
•
•
Plug and Play (including bus and device enumeration)
Power management control of individual devices, add-in boards (some add-in boards may
require an ACPI-aware driver), video displays, and hard disk drives
Methods for achieving less than 15-watt system operation in the power-on/standby
sleeping state
•
•
•
•
A Soft-off feature that enables the operating system to power-off the kit
Support for multiple wake-up events (see Table 9 on page 33)
Support for a front panel power and sleep mode switch
Table 7 lists the system states based on how long the power switch is pressed, depending on how
ACPI is configured with an ACPI-aware operating system.
Table 7. Effects of Pressing the Power Switch
If the system is in this state…
…and the power switch is pressed for
…the system enters this state
Off
Less than four seconds
Power-on
(ACPI G2/G5 – Soft off)
(ACPI G0 – working state)
On
Less than four seconds
More than six seconds
Less than four seconds
More than six seconds
Soft-off/Standby
(ACPI G0 – working state)
(ACPI G1 – sleeping state) Note
On
Fail safe power-off
(ACPI G2/G5 – Soft off)
(ACPI G0 – working state)
Sleep
Wake-up
(ACPI G0 – working state)
(ACPI G1 – sleeping state)
Sleep
Power-off
(ACPI G1 – sleeping state)
(ACPI G2/G5 – Soft off)
Note: Depending on power management settings in the operating system.
31
1.14.1.1
System States and Power States
Under ACPI, the operating system directs all system and device power state transitions. The
operating system puts devices in and out of low-power states based on user preferences and
knowledge of how devices are being used by applications. Devices that are not being used can be
turned off. The operating system uses information from applications and user settings to put the
system as a whole into a low-power state.
Table 8 lists the power states supported by the kit along with the associated system power
targets. See the ACPI specification for a complete description of the various system and power
states.
Table 8. Power States and Targeted System Power
Processor
States
Targeted System
Power (Note 1)
Global States
Sleeping States
Device States
G0 – working
S0 – working
C0 – working
D0 – working state.
Full power > 30 W
state
(Note 2)
G1 – sleeping
state
S3 – Suspend to RAM. No power
Context saved to
RAM.
D3 – no power
except for wake-up
logic.
Power < 5 W
(Note 2)
G1 – sleeping
state
S4 – Suspend to disk.
Context saved to disk.
No power
No power
No power
D3 – no power
except for wake-up
logic.
Power < 5 W
(Note 2)
G2/S5
S5 – Soft off. Context
not saved. Cold boot
is required.
D3 – no power
except for wake-up
logic.
Power < 5 W
G3 – mechanical
off
No power to the
system.
D3 – no power for
wake-up logic,
except when
provided by battery
or external source.
No power to the system.
Service can be performed
safely.
AC power is
disconnected
from the
computer.
Notes:
1. Total system power is dependent on the system configuration, including add-in boards and peripherals powered by
the system chassis’ power supply.
2. Dependent on the standby power consumption of wake-up devices used in the system.
32
Product Description
1.14.1.2
Wake-up Devices and Events
Table 9 lists the devices or specific events that can wake the kit from specific states.
Table 9. Wake-up Devices and Events
Devices/events that wake up the system…
…from this sleep state
S3, S4, S51
Comments
Power switch
RTC alarm
LAN
S3, S4, S51
Monitor to remain in sleep state
S3, S4, S51, 3
“S5 WOL after G3” must be supported;
monitor to remain in sleep state
USB
S3, S4, S51, 2, 3
S3, S4, S51
Wake S4, S5 controlled by BIOS option
(not after G3)
WAKE#
Via WAKE; monitor to remain in sleep
state
1, 3
Consumer IR
Bluetooth
Will not wake when in Deep S4/S5 sleep
state
S3, S4, S5
N/A
Wake from Bluetooth is not supported
Notes:
1. S4 implies operating system support only.
2. Will not wake from Deep S4/S5. USB S4/S5 Power is controlled by BIOS. USB S5 wake is controlled by BIOS. USB S4
wake is controlled by OS driver, not just BIOS option.
3. Windows 10 Fast startup will block wake from LAN, USB, and CIR from S5.
NOTE
The use of these wake-up events from an ACPI state requires an operating system that provides
full ACPI support. In addition, software, drivers, and peripherals must fully support ACPI wake
events.
1.14.2
Hardware Support
The kit provides several power management hardware features, including:
•
•
•
•
•
•
•
Wake from Power Button signal
Instantly Available PC technology
LAN wake capabilities
Wake from USB (not after G3)
WAKE# signal wake-up support
Wake from S5
Wake from CIR
NOTE
The use of Wake from USB from an ACPI state requires an operating system that provides full
ACPI support.
33
1.14.2.1
Power Input
When resuming from an AC power failure, the kit returns to the power state it was in before
power was interrupted (on or off). The kit’s response can be set using the Last Power State
feature in the BIOS Setup program’s Boot menu.
1.14.2.2
Instantly Available PC Technology
Instantly Available PC technology enables the kit to enter the ACPI S3 (Suspend-to-RAM) sleep-
state. While in the S3 sleep-state, the computer will appear to be off (the power supply is only
supplying Standby power, and the front panel LED will be amber or secondary color if dual
colored, or off if single colored.) When signaled by a wake-up device or event, the system quickly
returns to its last known wake state. Table 9 on page 33 lists the devices and events that can
wake the computer from the S3 state.
The use of Instantly Available PC technology requires operating system support and drivers for
any installed M.2 add-in card.
1.14.2.3
LAN Wake Capabilities
LAN wake capabilities enable remote wake-up of the kit through a network. The LAN subsystem
monitors network traffic at the Media Independent Interface. Upon detecting a Magic Packet*
frame, the LAN subsystem asserts a wake-up signal that powers up the kit.
1.14.2.4
Wake from USB
USB bus activity wakes the computer from an ACPI S3 state (not after G3).
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
1.14.2.5
WAKE# Signal Wake-up Support
When the WAKE# signal on the PCI Express bus is asserted, the kit wakes from an ACPI S3, S4, or
S5 state.
1.14.2.6
Wake from S5
When the RTC Date and Time is set in the BIOS, the kit will automatically wake from an ACPI S5
state.
1.14.2.7
Wake from Consumer IR
CIR activity wakes the kit from an ACPI S3, S4, or S5 state.
34
Product Description
1.15 Intel Platform Security Technologies
Intel platform security technologies provides tools and resources to help the user protect their
information by creating a safer computing environment.
NOTE
Software with security capability is required to take advantage of Intel platform security
technologies.
1.15.1
Intel® Virtualization Technology
Intel Virtualization Technology (Intel® VT) is a hardware-assisted technology that, when
combined with software-based virtualization solutions, provides maximum system utilization by
consolidating multiple environments into a single server or client.
NOTE
A processor with Intel VT does not guarantee that virtualization will work on your system. Intel VT
requires a computer system with a chipset, BIOS, enabling software and/or operating system,
device drivers, and applications designed for this feature.
For information about
Refer to
Intel Virtualization Technology
http://www.intel.com/technology/virtualization/technology.htm
1.15.2
Intel® Platform Trust Technology
Intel® Platform Trust Technology (Intel® PTT) is a platform functionality for credential storage
and key management. Intel® PTT supports Microsoft* BitLocker* Drive Encryption for hard drive
encryption and supports all Microsoft requirements for firmware Trusted Platform Module (fTPM)
2.0.
NOTE
Support for fTPM version 2.0 requires a UEFI-enabled operating system, such as Microsoft*
Windows* 10.
CAUTION
BIOS recovery using the BIOS security jumper clears Intel® Platform Trust Technology (Intel® PTT)
keys. These keys will not be restored after the BIOS recovery.
For information about
Refer to
Intel Platform Trust Technology
http://www.intel.com/content/dam/www/public/us/en/documents
/white-papers/enterprise-security-platform-trust-technology-
white-paper.pdf
35
1.16 Thunderbolt 3
The board supports two Thunderbolt™ 3 ports sharing up to 40Gbps of data throughput. Each
port can support one 4k (60Hz) monitor output, USB3.1 (Gen 2) connection and charging
capabilities up to 5V at 3A via the back panel USB Type-C connectors. Item C in figure 7 shows
the location of the rear panel USB Type-C ports.
For information about
Refer to
https://www.intel.com/content/www/us/en/support/article
s/000027040/mini-pcs/intel-nuc-kits.html
Thunderbolt™ 3 information
http://www.intel.com/Thunderbolt
36
2
Technical Reference
2.1
Memory Resources
2.1.1
Addressable Memory
The kit utilizes 32 GB of addressable system memory. Typically the address space that is
allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash
device), and chipset overhead resides above the top of DRAM (total system memory). On a
system that has 32 GB of system memory installed, it is not possible to use all of the installed
memory due to system address space being allocated for other system critical functions. These
functions include the following:
•
•
•
•
•
•
•
BIOS/SPI Flash device (64 Mb)
Local APIC (19 MB)
Direct Media Interface (40 MB)
PCI Express configuration space (256 MB)
PCH base address registers PCI Express ports (up to 256 MB)
Memory-mapped I/O that is dynamically allocated for M.2 add-in cards (256 MB)
Integrated graphics shared memory (up to 512 MB; 64 MB by default)
The kit provides the capability to reclaim the physical memory overlapped by the memory
mapped I/O logical address space. The kit remaps physical memory from the top of usable DRAM
boundary to the 4 GB boundary to an equivalent sized logical address range located just above
the 4 GB boundary. All installed system memory can be used when there is no overlap of system
addresses.
2.2
Connectors and Headers
CAUTION
Only the following connectors and headers have overcurrent protection: back panel and front
panel USB.
The other internal connectors and headers are not overcurrent protected and should connect only
to devices inside the kit’s chassis, such as fans and internal peripherals. Do not use these
connectors or headers to power devices external to the kit’s chassis. A fault in the load presented
by the external devices could cause damage to the board, the power cable, and the external
devices themselves.
Furthermore, improper connection of USB header single wire connectors may eventually overload
the overcurrent protection and cause damage to the board.
37
This section describes the connectors and headers. The connectors and headers can be divided
into these groups:
•
•
•
Front panel connectors
Back panel connectors
Top-Side headers and connectors
2.2.1
Front Panel Connectors
Figure 6 shows the location of the components on the front of the Intel NUC Kit NUC8i7HV
chassis.
Figure 6. Front Panel Layout
Table 10. Components Shown in Figure 6
Item from Figure 6
Description
A
B
C
D
E
F
G
H
I
Power on/off button/LED
Consumer Infrared (CIR)
SDXC card reader slot
Front USB Port USB 3.1 Gen 2
Front USB Port USB 3.0 / Charging
HDMI Port
Digital Microphones
USB Type-C port
Speaker/Headset
38
Technical Reference
2.2.1.1
Consumer Infrared (CIR) Sensor
The Consumer Infrared (CIR) sensor on the front panel provides features that are designed to
comply with Microsoft Consumer Infrared usage models (RC-6).
The CIR feature is made up of the receiving sensor. The receiving sensor consists of a filtered
translated infrared input compliant with Microsoft CIR specifications.
Customers are required to provide their own media center compatible remote or smart phone
application for use with the Intel NUC. The Location of the CIR is called out as Item B in Table 10
above.
2.2.1.2
Digital Microphone Array
The digital microphone array consists of quad front facing digital microphones located across the
front panel to implement the far-field algorithm to minimize acoustic interference. Item E from
Figure 12 referencing shows the location of the digital microphone array connector. Table 18 lists
the signal names of the DMIC connector. See item G from Figure 6 the physical locations of the
DMIC array on the Intel NUC Kit NUC8i7HVK chassis.
39
2.2.2
Back Panel Connectors
Figure 7 shows the location of the components on the back of the Intel NUC Kit NUC8i7HV
chassis.
Figure 7. Back Panel Layout
Table 11. Components Shown in Figure 7
Item from Figure 7
Description
A
B
C
D
E
Speaker/SPDIF
19.5v DC power input jack
Thunderbolt™ 3 port (Type C)
Mini DisplayPort connectors
Ethernet Ports
F
USB 3.0 Ports
G
H
HDMI Connector
Anti-Theft key lock hole (located on side of unit)
40
Technical Reference
2.2.3
USB and I/O Headers
Figure 8 shows the location of the USB and I/O headers on the top-side of Intel NUC Kit
NUC8i7HV.
Figure 8. Headers and Connectors (Top)
Table 12. Headers and Connectors Shown in Figure 8
Item from Figure 8
Description
A
B
Front panel USB 3.0 header (1.25 mm pitch) (blue)
Internal Common IO header (1.25 mm pitch) (white)
2.2.3.1
Internal 15-pin Auxiliary SATA power connector.
The board has an internal 15-pin auxiliary SATA (male) power connector available for expansion
purposes through additional storage or other custom solutions. Location is designated in Table
13-I referenced by Figure 11.
Table 13. Auxiliary SATA power connector pin out
Pin #
Signal Name
41
1
3.3 V DC
3.3 V DC
3.3 V DC
Ground
Ground
Ground
5 V DC
2
3
4
5
6
7
8
5 V DC
9
5 V DC
10
11
12
13
14
15
Ground
Ground
Ground
12 V DC
12 V DC
12 V DC
The 15-pin auxiliary SATA power connector follows the standard pin-out for SATA power
connectors with 12V, 5V, 3.3V, and GND/common.
The board power supplied through the Auxiliary SATA power connector is rated at a maximum of:
•1.5 Amps from 12V rail
•1.0 Amps from 5V rail
•1.0 Amps from 3.3V rail
NOTE
The power that is provided by the 15-pin auxiliary SATA power connector is calculated into the
power reading that is used to govern the overall system power consumption state. System may
experience power throttling at an earlier than normal state as a result.
CAUTION
Do not install or remove the SATA power connector with the power on. Always turn off the power
and unplug the power cord from the computer before connecting the auxiliary SATA power
connector. Otherwise, the board could be damaged.
42
Technical Reference
2.2.3.2 Internal USB 3.0 Header (1.25 mm Pitch)
Figure 9 is a connection diagram for internal USB .30 header.
NOTE
•
•
The +5 V DC power on the USB header is fused.
Use only an internal USB connector that conforms to the USB 3.0 specification for high-speed
USB devices.
Figure 9. USB 3.0 Internal Header (1.25 mm Pitch)
NOTE
Connector is Molex part number 5041871874, 1.25 mm pitch header, surface mount, vertical.
43
2.2.3.3 Internal Common IO Header (1.25 mm Pitch)
Figure 10 is a connection diagram for internal Common IO header.
NOTE
•
•
The +5 V DC power on the USB header is fused.
Use only an internal USB connector that conforms to the USB 2.0 specification for high-speed
USB devices.
Figure 10. Connection Diagram for the Internal
IO Common Header (1.25 mm Pitch)
NOTE
Pin number 13 on the connector is an output. The PCH asserts RST_N (out) to reset devices
attached to front panel header. Asserted during power-up and when software initiates a hard
reset.
NOTE
Connector is Entry part number 3950K-J20C-00L, 1.25 mm pitch header, surface mount, vertical.
2.2.3.3.1
Consumer Electronics Control (CEC) Header
The Consumer Electronics Control (CEC) is a 500 Mb/s bi-directional serial bus designed to be
used for controlling multiple HDMI devices with a single remote control.
For information about
Refer to
HDMI CEC technology
http://www.hdmi.org/pdf/whitepaper/DesigningCECintoYourNextH
DMIProduct.pdf
44
Technical Reference
Figure 11 shows the location of all user addressable headers and connectors on the top-side of
the Intel NUC Kit NUC8i7HV.
Figure 11. Additional Headers and Connectors
Table 14. Headers and Connectors Shown in Figure 11
Item from Figure 11
Description
A
B
C
D
E
F
Fan Header 1
Fan Header 2M.2 connector B (key type M) for 2242 and 2280 modules
SODIMM A M.2 connector A (key type M) for 2242 and 2280 modules
SODIMM B
Digital Microphone Header
RTC Battery Header (2pin)
G
H
I
RGB LED Header for Top Lid
BIOS Security Jumper
Auxiliary SATA Power Header
J
M.2 Key E (pre-populated with 2230 WIFI Solution)
Internal Common IO Header
K
L
M.2 connector A (key type M) for 2242 and 2280 modules
Internal USB 3.0 Header
M
N
M.2 connector B (key type M) for 2280 modules
45
2.2.3.4
BIOS Security Jumper
CAUTION
Do not move a jumper with the power on. Always turn off the power and unplug the power cord
from the computer before changing a jumper setting. Otherwise, the board could be damaged.
Figure 12 shows the BIOS Security Jumper. The 3-pin jumper determines the BIOS Security
program’s mode.
Table 15 describes the jumper settings for the three modes: normal, lockdown, and
configuration.
Figure 12. BIOS Security Jumper
46
Technical Reference
Table 15 lists the settings for the jumper.
Table 15. BIOS Security Jumper Settings
Function/Mode
Jumper Setting
Configuration
Normal
1-2
The BIOS uses current configuration information and passwords for
booting.
Lockdown
2-3
The BIOS uses current configuration information and passwords for
booting, except:
•
All POST Hotkeys are suppressed (prompts are not displayed and keys
are not accepted. For example, F2 for Setup, F10 for the Boot Menu).
•
Power Button Menu is not available (see Section 3.7.4 Power Button
Menu).
BIOS updates are not available except for automatic Recovery due to flash
corruption.
Configuration
None
BIOS Recovery Update process if a matching *.bio file is found. Recovery
Update can be cancelled by pressing the Esc key.
If the Recovery Update was cancelled or a matching *.bio file was not
found, a Config Menu will be displayed. The Config Menu consists of the
following (selected Power Button Menu options):
[1] Suppress this menu until the BIOS Security Jumper is replaced.
[2] Clear BIOS User and Supervisor Passwords.
See Section 3.7.4 Power Button Menu.
2.2.3.5
Add-in Card Connectors
The kit supports M.2 2242 and 2280 (key type M) modules.
•
•
Supports M.2 SSD SATA-III drives
― Maximum bandwidth is approximately 540 MB/s
Supports M.2 SSD Gen 3 PCIe AHCI, NVMe drives (PCIe x1, x2, and x4)
― Using PCIe x4 M.2 SSD maximum bandwidth is approximately 4000 MB/s
Table 16. M.2 2280 Module (key type M) Connectors
Pin
74
72
70
68
66
64
62
60
58
Signal Name
3.3V
Pin
75
73
71
69
67
65
63
61
59
Signal Name
GND
3.3V
GND
3.3V
GND
SUSCLK(32kHz) (O)(0/3.3V)
Connector Key
Connector Key
Connector Key
Connector Key
N/C
PEDET (NC-PCIe/GND-SATA)
N/C
Connector Key
Connector Key
Connector Key
Connector Key
47
continued
Table 16. M.2 2280 Module (key type M) Connectors (continued)
Pin
56
54
52
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
Signal Name
Pin
57
55
53
51
49
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
Signal Name
GND
N/C
PEWAKE# (I/O)(0/3.3V) or N/C
REFCLKP
REFCLKN
GND
CLKREQ# (I/O)(0/3.3V) or N/C
PERST# (O)(0/3.3V) or N/C
N/C
PETp0/SATA-A+
PETn0/SATA-A-
GND
N/C
N/C
N/C
PERp0/SATA-B-
PERn0/SATA-B+
GND
N/C
DEVSLP (O)
N/C
PETp1
N/C
PETn1
N/C
GND
N/C
PERp1
N/C
PERn1
N/C
GND
N/C
PETp2
N/C
PETn2
N/C
GND
3.3V
PERp2
3.3V
PERn2
3.3V
GND
3.3V
PETp3
DAS/DSS# (I/O)/LED1# (I)(0/3.3V)
PETn3
N/C
N/C
3.3V
3.3V
GND
6
7
PERp3
4
5
PERn3
2
3
GND
1
GND
48
Technical Reference
2.2.3.6 Kit Dimensions
Figure 13 illustrates the dimensions for the kit. Dimensions are given in millimeters.
Figure 13. Kit Dimensions
49
2.3
VESA Bracket
Figure 14 illustrates how to install the VESA mount bracket included with the kit.
Figure 14. Install VESA Bracket
50
Technical Reference
Figure 15 shows the dimensions of the VESA bracket. Dimensions are given in millimeters.
Figure 15. VESA Bracket Dimensions
2.4
Mechanical Considerations
2.4.1
Weights
Table 17 lists select weights of boards and kits.
Table 17. Select Weights
Item
Weight (in kg)
Board with Thermal Solution
0.2
0.6
0.6
Tall Kit (includes Board Assembly)
Tall Mini PC (includes Board Assembly,
memory, and drive)
51
2.5
Power Supply
The NUC8i7HV uses an AC to DC power adapter with a six foot attached cable with a barrel
connector. Figure 16 shows the power adapter and plugs that may be included with the kit.
•
•
•
100-240V AC Input 50-60 Hz 3.5 A
19.5V 11.8 A DC output
3-pin AC Power Cord Plug
AC power cord options are as follows:
•
•
•
•
•
No AC Power Cord
US AC Power Cord
UK AC Power Cord
EU AC Power Cord
AU AC Power Cord
Figure 16. Power Adapter and Plugs Included with the Kit
52
Technical Reference
2.5.1
Power Supply Connector
The kit has the following power supply connector:
•
External Power Supply – the kit can be powered through a 19.5v DC connector on the back
panel (see Figure 16, C). The back panel DC connector is compatible with a 7.4mm/OD (outer
diameter) and 5.0 mm/ID (inner diameter) plug, where the inner 0.8mm contact is +19.5
(±10%) V DC and the shell is GND. The maximum current rating is 11.8 A.
NOTE
External power voltage, 19.5v DC, is dependent on the type of power brick used.
2.5.1.1.1
Power Sensing Circuit
The kit has a power sensing circuit that:
•
•
Manages CPU power usage to maintain system power consumption below 230 W.
Designed for use with 230 W AC-DC adapters.
NOTE
It is recommended that you disable this feature (via BIOS option) when using an AC-DC
adapter greater than 230 W.
2.5.2
Fan Header Current Capability
Table 18 lists the current capability of the fan header.
Table 18. Dual Fan Header Current Capability
Fan Header
Maximum Available Current
Processor fan 1
Processor fan 2
0.75 A
0.75 A
2.6
Reliability
The Mean Time Between Failures (MTBF) prediction is calculated using component and
subassembly random failure rates. The calculation is based on the Telcordia SR-332 Issue 2,
Method I, Case 3, 55 ºC ambient. The MTBF prediction is used to estimate repair rates and spare
parts requirements. The MTBF for Intel NUC8i7HV Kit is TBD Hours.
53
2.7
Environmental
Table 19 lists the environmental specifications.
Table 19. Environmental Specifications
Parameter
Specification
Temperature
Non-Operating
Operating
-40 C to +60 C
0 C to +35 C
The operating temperature of the system may be determined by measuring the air
temperature from the junction of the heatsink fins and fan, next to the attachment screw,
in a closed chassis, while the system is in operation.
Shock
Unpackaged
50 g trapezoidal waveform
Velocity change of 170 inches/s²
Half sine 2 millisecond
Packaged
Product Weight (pounds)
Free Fall (inches)
Velocity Change (inches/s²)
<20
36
30
24
18
167
152
136
118
21-40
41-80
81-100
Vibration
Unpackaged
5 Hz to 20 Hz: 0.001 g²/Hz sloping up to 0.01 g²/Hz
20 Hz to 500 Hz: 0.01 g²/Hz (flat)
Input acceleration is 2.20 g RMS
Packaged
5 Hz to 40 Hz: 0.015 g²/Hz (flat)
40 Hz to 500 Hz: 0.015 g²/Hz sloping down to 0.00015 g²/Hz
Input acceleration is 1.09 g RMS
Note: Before attempting to operate this system, the overall temperature of the system must be above the minimum
operating temperature specified. It is recommended that the system temperature be at least room temperature
before attempting to power on the system. The operating and non-operating environment must avoid condensing
humidity.
54
3
Overview of BIOS Features
3.1
Introduction
The kit uses Intel® Visual BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI
Flash) and can be updated using a disk-based program. The SPI Flash contains the Visual BIOS
Setup program, POST, the PCI auto-configuration utility, LAN EEPROM information, and Plug and
Play support.
The BIOS displays a message during POST identifying the type of BIOS and a revision code. The
initial production BIOSs are identified as HNKBLi70.86A.
The Visual BIOS Setup program can be used to view and change the BIOS settings for the
computer. The BIOS Setup program is accessed by pressing the <F2> key after the Power-On
Self-Test (POST) memory test begins and before the operating system boot begins.
NOTE
The maintenance menu is displayed only when the kit is in configure mode. Section 2.2.3.4 on
page 46 shows how to put the kit in configure mode.
3.2
3.3
BIOS Flash Memory Organization
The Serial Peripheral Interface Flash Memory (SPI Flash) includes a 64 Mb flash memory device.
System Management BIOS (SMBIOS)
SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in
a managed network.
The main component of SMBIOS is the Management Information Format (MIF) database, which
contains information about the computing system and its components. Using SMBIOS, a system
administrator can obtain the system types, capabilities, operational status, and installation dates
for system components. The MIF database defines the data and provides the method for
accessing this information. The BIOS enables applications such as third-party management
software to use SMBIOS. The BIOS stores and reports the following SMBIOS information:
•
•
•
•
BIOS data, such as the BIOS revision level
Fixed-system data, such as peripherals, serial numbers, and asset tags
Resource data, such as memory size, cache size, and processor speed
Dynamic data, such as event detection and error logging
Non-Plug and Play operating systems require an additional interface for obtaining the SMBIOS
information. The BIOS supports an SMBIOS table interface for such operating systems. Using
this support, an SMBIOS service-level application running on a non-Plug and Play operating
system can obtain the SMBIOS information. Additional kit information can be found in the BIOS
under the Additional Information header under the Main BIOS page.
55
3.4
Legacy USB Support
Legacy USB support enables USB devices to be used even when the operating system’s USB
drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and
to install an operating system that supports USB. By default, Legacy USB support is set to
Enabled.
Legacy USB support operates as follows:
1. When you apply power to the computer, legacy support is disabled.
2. POST begins.
3. Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to enter and
configure the BIOS Setup program and the maintenance menu.
4. POST completes.
5. The operating system loads. While the operating system is loading, USB keyboards and mice
are recognized and may be used to configure the operating system. (Keyboards and mice are
not recognized during this period if Legacy USB support was set to Disabled in the BIOS
Setup program.)
6. After the operating system loads the USB drivers, all legacy and non-legacy USB devices are
recognized by the operating system, and Legacy USB support from the BIOS is no longer
used.
To install an operating system that supports USB, verify that Legacy USB support in the BIOS
Setup program is set to Enabled and follow the operating system’s installation instructions.
3.5
BIOS Updates
The BIOS can be updated using one of the following methods:
•
•
•
Intel Express BIOS Update Utility, which enables automated updating while in the Windows
environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB
drive (a flash drive or a USB hard drive), or a CD-ROM, or from the file location on the Web.
Intel Flash Memory Update Utility, which requires booting from DOS. Using this utility, the
BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive),
or a CD-ROM.
Intel® F7 switch during POST allows a user to select where the BIOS .bio file is located and
perform the update from that location/device. Similar to performing a BIOS Recovery without
removing the BIOS configuration jumper.
•
•
Intel® Visual BIOS has an option to update the BIOS from a valid .bio file located on a hard
disk or USB drive. Enter Intel Visual BIOS by pressing <F2> during POST.
Using Front Panel menu option
Both utilities verify that the updated BIOS matches the target system to prevent accidentally
installing an incompatible BIOS.
NOTE
Review the instructions distributed with the upgrade utility before attempting a BIOS update.
56
Overview of BIOS Features
For information about
Refer to
BIOS update utilities
http://support.intel.com/support/motherboards/desktop/sb/CS-
034499.htm
3.5.1
Language Support
The BIOS Setup program and help messages are supported in US English. Check the Intel web
site for support.
3.6
BIOS Recovery
It is unlikely that anything will interrupt a BIOS update; however, if an interruption occurs, the
BIOS could be damaged. Table 20 lists the drives and media types that can and cannot be used
for BIOS recovery. The BIOS recovery media does not need to be made bootable.
Table 20. Acceptable Drives/Media Types for BIOS Recovery
Media Type (Note)
Can be used for BIOS recovery?
Hard disk drive (connected to USB)
CD/DVD drive (connected to USB)
USB flash drive
Yes
Yes
Yes
USB diskette drive (with a 1.4 MB diskette)
No (BIOS update file is bigger than 1.4 MB size limit)
NOTE
Supported file systems for BIOS recovery:
•
•
•
•
•
NTFS (sparse, compressed, or encrypted files are not supported)
FAT32
FAT16
FAT12
ISO 9660
For information about
Refer to
BIOS recovery
http://www.intel.com/support/motherboards/desktop/sb/cs-034524.htm
3.7
Boot Options
In the BIOS Setup program, the user can choose to boot from a hard drive, removable drive, or
the network. The default setting is for the hard drive first, removable drive second, and the
network third.
3.7.1
Network Boot
The network can be selected as a boot device. This selection allows booting from the onboard
LAN or a network add-in card with a remote boot ROM installed.
57
Pressing the <F12> key during POST automatically forces booting from the LAN. To use this key
during POST, the User Access Level in the BIOS Setup program's Security menu must be
set to Full.
3.7.2
Booting Without Attached Devices
For use in embedded applications, the BIOS has been designed so that after passing the POST,
the operating system loader is invoked even if the following devices are not present:
•
•
•
Video Display
Keyboard
Mouse
3.7.3
Changing the Default Boot Device During POST
Pressing the <F10> key during POST causes a boot device menu to be displayed. This menu
displays the list of available boot devices. Table 21 lists the boot device menu options.
Table 21. Boot Device Menu Options
Boot Device Menu Function Keys
Description
<> or <>
<Enter>
<Esc>
Selects a default boot device
Exits the menu, and boots from the selected device
Exits the menu and boots according to the boot priority defined
through BIOS setup
58
Overview of BIOS Features
3.7.4
Power Button Menu
As an alternative to Back-to-BIOS Mode or normal POST Hotkeys, the user can use the power
button to access a menu. The Power Button Menu is accessible via the following sequence:
1. System is in S4/S5/G2
2. User pushes the power button and holds it down for 3 seconds
3. The system will emit three short beeps from the front panel (FP) audio port, then stop to
signal the user to release the power button. The FP power button LED will also change from
Blue to Amber when the user can release the power button.
4. User releases the power button before the 4-second shutdown override
If this boot path is taken, the BIOS will use default settings, ignoring settings in VPD where
possible.
At the point where Setup Entry/Boot would be in the normal boot path, the BIOS will display the
following prompt and wait for a keystroke:
[ESC] Normal Boot
[F2]
[F3]
[F4]
[F7]
Intel Visual BIOS
Disable Fast Boot
BIOS Recovery
Update BIOS
[F10] Enter Boot Menu
[F12] Network Boot
[F2] Enter Setup is displayed instead if Visual BIOS is not supported.
[F3] Disable Fast Boot is only displayed if at least one Fast Boot optimization is enabled.
[F9] Remote Assistance is only displayed if Remote Assistance is supported.
If an unrecognized key is hit, then the BIOS will beep and wait for another keystroke. If one of the
listed hotkeys is hit, the BIOS will follow the indicated boot path. Password requirements must
still be honored.
If Disable Fast Boot is selected, the BIOS will disable all Fast Boot optimizations and reset the
system.
59
3.8
Hard Disk Drive Password Security Feature
The Hard Disk Drive Password Security feature blocks read and write accesses to the hard disk
drive until the correct password is given. Hard Disk Drive Passwords are set in BIOS SETUP and
are prompted for during BIOS POST. For convenient support of S3 resume, the system BIOS will
automatically unlock drives on resume from S3. Valid password characters are A-Z, a-z, and 0-9.
Passwords may be up to 19 characters in length.
The User hard disk drive password, when installed, will be required upon each power-cycle until
the Master Key or User hard disk drive password is submitted.
The Master Key hard disk drive password, when installed, will not lock the drive. The Master Key
hard disk drive password exists as an unlock override in the event that the User hard disk drive
password is forgotten. Only the installation of the User hard disk drive password will cause a hard
disk to be locked upon a system power-cycle.
Table 22 shows the effects of setting the Hard Disk Drive Passwords.
Table 22. Master Key and User Hard Drive Password Functions
Password Set
Neither
Password During Boot
None
Master only
User only
None
User only
Master and User Set
Master or User
During every POST, if a User hard disk drive password is set, POST execution will pause with the
following prompt to force the user to enter the Master Key or User hard disk drive password:
Enter Hard Disk Drive Password:
Upon successful entry of the Master Key or User hard disk drive password, the system will
continue with normal POST.
If the hard disk drive password is not correctly entered, the system will go back to the above
prompt. The user will have three attempts to correctly enter the hard disk drive password. After
the third unsuccessful hard disk drive password attempt, the system will halt with the message:
Hard Disk Drive Password Entry Error
A manual power cycle will be required to resume system operation.
NOTE
As implemented on Intel NUC Kit NUC8i7HV, Hard Disk Drive Password Security is only supported
on SATA port 0 (M.2 ). The passwords are stored on the hard disk drive so if the drive is relocated
to another computer that does not support Hard Disk Drive Password Security feature, the drive
will not be accessible.
Currently, there is no industry standard for implementing Hard Disk Drive Password Security on
AHCI or NVME drives. Hard drive encryption can still be implemented and does not require Hard
Disk Drive Password Security.
3.9
BIOS Security Features
The BIOS includes security features that restrict access to the BIOS Setup program and who can
boot the computer. A supervisor password and a user password can be set for the BIOS Setup
program and for booting the computer, with the following restrictions:
60
Overview of BIOS Features
•
•
•
•
The supervisor password gives unrestricted access to view and change all the Setup options
in the BIOS Setup program. This is the supervisor mode.
The user password gives restricted access to view and change Setup options in the BIOS
Setup program. This is the user mode.
If only the supervisor password is set, pressing the <Enter> key at the password prompt of
the BIOS Setup program allows the user restricted access to Setup.
If both the supervisor and user passwords are set, users can enter either the supervisor
password or the user password to access Setup. Users have access to Setup respective to
which password is entered.
•
Setting the user password restricts who can boot the computer. The password prompt will be
displayed before the computer is booted. If only the supervisor password is set, the
computer boots without asking for a password. If both passwords are set, the user can enter
either password to boot the computer.
•
•
For enhanced security, use different passwords for the supervisor and user passwords.
Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 20 characters in
length.
•
To clear a set password, enter a blank password after entering the existing password.
Table 23 shows the effects of setting the supervisor password and user password. This table is
for reference only and is not displayed on the screen.
Table 23. Supervisor and User Password Functions
Supervisor
Password Set Mode
Password to
Enter Setup
Password
During Boot
User Mode
Setup Options
Neither
Can change all
options
Can change all
options
None
None
None
None
(Note)
(Note)
Supervisor only Can change all
options
Can change a
limited number
of options
Supervisor Password
Supervisor
User only
N/A
Can change all
options
Enter Password
Clear User Password
User
User
Supervisor and
user set
Can change all
options
Can change a
limited number
of options
Supervisor Password
Enter Password
Supervisor or
user
Supervisor or
user
Note:
If no password is set, any user can change all Setup options.
61
3.10 System LED Functionality
The NUC system includes configurable RGB LED functionality in both the top cover skull lid as
well as the front panel status LEDs. The LEDs in both the Top and the Front panel are software
configurable with the WMI command set.
Error! Reference source not found. shows the default location and behavior configurations of the
RGB LEDs that are present on the system.
Table 24. Default RGB LED Locations and Behaviors
Location
Default Behavior
Power Status, S0 and S3.
Storage Disk Activity
Ethernet Activity
Default Colors
Front panel Power Button
Front Panel LED 1
Front Panel LED 2
Front Panel LED 3
S0 – Blue solid, S3 – Blue Blinking
Default Off, flash red during activity
Default On when Network connected, Flash Off during activity
System Performance
Green Transitions to Red, measures power consumption based
on
Top Cover Skull Outline
Top Cover Eyes
Power Status, S0 and S3.
Power Status, S0 and S3.
S0 – Blue Solid, S3 – Blue Blinking
S0 – Blue Solid, S3 – Blue Blinking
For more behaviors please download the Intel NUC LED Companion Application from
https://downloadcenter.intel.com/download/27641
62
4
Error Messages and Blink Codes
4.1
Front-panel Power LED Blink Codes
Whenever a recoverable error occurs during POST, the BIOS causes the kit’s front panel power
LED to blink an error message describing the problem (see Table 25).
Table 25. Front-panel Power LED Blink Codes
Type
Pattern
Note
Power-on
Solid on primary color. Indicates S0 state.
Default to On; can be disabled
via BIOS Setup
S3 Standby
Blink primary color .25 seconds on, .25 seconds off,
indefinitely. Indicates S3 state.
Default behavior; can be
changed via BIOS Setup
Intel Ready Mode
BIOS update in progress
Solid secondary color
Default behavior; can be
changed via BIOS Setup
Off when the update begins, then primary color on for
0.5 seconds, then off for 0.5 seconds. The pattern
repeats until the BIOS update is complete.
Memory error
On-off (1.0 second each) three times, then 2.5-second
pause (off), entire pattern repeats (blinks and pause)
until the system is powered off.
Thermal trip warning
Blink primary color .25 seconds on, .25 seconds off, .25
seconds on, .25 seconds off. This will result in a total of
16 blinks (blink for 8 seconds).
4.2
BIOS Error Messages
Table 26 lists the error messages and provides a brief description of each.
Table 26. BIOS Error Messages
Error Message
Explanation
CMOS Battery Low
CMOS Checksum Bad
The battery may be losing power. Replace the battery soon.
The CMOS checksum is incorrect. CMOS memory may have been
corrupted. Run Setup to reset values.
Memory Size Decreased
No Boot Device Available
Memory size has decreased since the last boot. If no memory was
removed, then memory may be bad.
System did not find a device to boot.
63
相关型号：
©2020 ICPDF网 联系我们和版权申明