SSDSC2BW180H6 [INTEL]
Intel® Solid-State Drive 535 Series (2.5-inch);型号: | SSDSC2BW180H6 |
厂家: | INTEL |
描述: | Intel® Solid-State Drive 535 Series (2.5-inch) |
文件: | 总31页 (文件大小:740K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Intel® Solid-State Drive 535 Series (2.5-inch)
Intel® Solid-State Drive 535 Series (2.5-inch)
Product Specification
Capacities: 56GB, 120GB, 180GB, 240GB,
Power
360GB, 480GB
Active (BAPCo MobileMark* 2007 Workload):
165 mW
Form Factor: 2.5-inch
Thickness: 7 mm
Idle3: 55 mW
DevSleep: 5 mW
Weight: Up to 78 grams
SATA 6Gb/s Bandwidth Performance1
Temperature
Operating4: 0o C to 70o C
Non-Operating: -55o C to 95o C
(IOMeter* Queue Depth 32)
Sustained Sequential Read: up to 540MB/s
Sustained Sequential Write: up to 490MB/s
Reliability
Read and Write IOPS1
Uncorrectable Bit Error Rate (UBER):
<1 sector per 1016 bits read
(IOMeter Queue Depth 32)
Mean Time Between Failure (MTBF):
1.2 million hours
Random 4KB Reads: up to 48,000 IOPS
Random 4KB Writes: up to 80,000 IOPS2
Shock
Data Compression
Operating and Non-Operating: 1,500 G/0.5 ms
End-to-End Data Protection
AES 256-bit Encryption
Compatibility
Vibration
Operating: 2.17 GRMS (5-700Hz)
Non-operating: 3.13 GRMS (5-800Hz)
® ®
Intel SSD Toolbox with Intel SSD Optimizer
Certifications and Declarations:
®
Intel Data Migration Software
UL*
CE*
C-Tick*
BSMI*
KCC*
Microsoft* WHCK
VCCI*
SATA-IO*
®
Intel Rapid Storage Technology
SATA Revision 3.2
ACS-3 (ATA/ATAPI Command Set 3)
SSD Enhanced SMART ATA feature set
Power Management
5.0 V SATA Supply Rail
SATA Link Power Management (LPM)
Advanced Power Management (APM)
Device Sleep (DevSleep)
Product Ecological Compliance
RoHS*
NOTES:
1.
2.
3.
4.
Performance values vary by capacity.
Random 4KB writes measured using out-of-box SSD.
Non-DevSleep idle power with SATA Link Power Management (LPM) enabled.
As measured by temperature sensor, SMART Attribute BEh. Active airflow is recommended within the system for maintaining proper
device operating temperatures on heavier workloads.
Order Number: 332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
Ordering Information
Contact your local Intel sales representative for ordering information.
Revision History
Revision Number
Description
Revision Date
Initial release
Updated Performance Rating in Table 4, 360GB Capacity
001
April 2015
002
003
April 2015
Updated Endurance Rating in Table 10, from 20GB to 40GB
Added 56GB Capacity
Sept 2015
Tests document performance of components on a particular test, in specific systems. Differences in hardware, software, or
configuration will affect actual performance. Consult other sources of information to evaluate performance as you consider your
purchase.
IOMeter* Test and System Configurations: Intel® Core™ i5-2400S (6MB L3 Cache, 2.5GHz), Intel Desktop Board DH67CF, Intel HD
Graphics driver 9.17.10.2875, BIOS: BLH6710H.84A.0160.2012.1204.1156, Chipset: Intel INF 9.2.0.1016, Memory: 4GB (2X2GB)
Kingston DDR3-1333, Intel RST driver 12.9, Microsoft Windows 7 Enterprise 64-bit with SP1.
For more complete information about performance and benchmark results, visit http://www.intel.com/performance
All documented endurance test results are obtained in compliance with JESD218 Standards; refer to individual sub-sections
within this document for specific methodologies. See www.jedec.org for detailed definitions of JESD218 Standards.
Low Halogen applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel
components as well as purchased components on the finished assembly meet JS-709 requirements, and the PCB/substrate
meet IEC 61249-2-21 requirements. The replacement of halogenated flame retardants and/or PVC may not be better for the
environment.
Intel and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2015 Intel Corporation. All rights reserved.
Product Specification
2
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
Contents
Revision History ......................................................................................................................... 2
1
Overview ...................................................................................................................... 5
1.1
1.2
Terms and Acronyms........................................................................................................ 6
Reference Documents....................................................................................................... 7
2
Product Specifications ..................................................................................................... 8
2.1
2.2
2.3
2.4
Capacity........................................................................................................................ 8
Performance .................................................................................................................. 8
Electrical Characteristics.................................................................................................... 9
Environmental Conditions.................................................................................................10
2.4.1
2.4.2
Temperature, Shock, Vibration .........................................................................10
Altitude..........................................................................................................10
2.5
2.6
2.7
Product Regulatory Compliance .........................................................................................11
Reliability .....................................................................................................................12
Hot Plug Support............................................................................................................12
3
4
Mechanical Information.................................................................................................. 13
Pin and Signal Descriptions............................................................................................. 14
4.1
4.2
Pin Locations ................................................................................................................14
Signal Descriptions .........................................................................................................14
4.2.1
4.2.2
Connector Pin Signal Definitions............................................................................14
Power Pin Signal Definitions .................................................................................15
4.3
Device Sleep Feature .......................................................................................................15
5
Supported Command and Feature Sets .............................................................................. 16
5.1
5.2
5.3
Supported ATA General Feature Command Set.......................................................................16
Advanced Power Management (APM) ...................................................................................19
Security .......................................................................................................................19
5.3.1
Sanitization Methods..........................................................................................19
5.4
5.5
5.6
5.7
5.8
5.9
Device Statistics .............................................................................................................19
Software Settings Preservation...........................................................................................20
DevSleep .....................................................................................................................21
SMART Command Transport .............................................................................................21
SMART Attributes ...........................................................................................................22
SMART Logs..................................................................................................................24
6
Certifications and Declarations ........................................................................................ 26
7
Appendix.................................................................................................................... 27
7.1
7.2
Identify Device...............................................................................................................27
Models ........................................................................................................................31
September 2015
332062-003US
Product Specification
3
Intel® Solid-State Drive 535 Series (2.5-inch)
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Glossary of Terms and Acronyms ............................................................................ 6
Standard References ........................................................................................... 7
User Addressable Sectors ..................................................................................... 8
Compressible Performance ................................................................................... 8
Incompressible Performance ................................................................................. 8
Latency........................................................................................................... 9
Operating Voltage and Power Consumption............................................................... 9
Temperature, Shock, Vibration ..............................................................................10
Product Regulatory Compliance Specifications ..........................................................11
Reliability Specifications ......................................................................................12
Serial ATA Connector Pin Definitions.......................................................................14
Serial ATA Power Pin Definitions............................................................................15
Supported ATA Commands and Feature Sets ............................................................16
APM Subcommand Codes for Power Management and Definitions ..................................19
APM Subcommand Codes for Thermal Power Management and Definitions.......................19
Supported Secure Erase Modes and Definitions .........................................................19
Supported Sanitize Device Modes and Definitions ......................................................19
Device Statistics Log...........................................................................................20
Preserved Software Settings .................................................................................20
DevSleep Control Parameters ...............................................................................21
SMART Attributes ..............................................................................................22
SMART Attribute Status Flags ...............................................................................24
Device Certifications and Declarations .....................................................................26
Identify Device Returned Sector Data ......................................................................27
Available Models ...............................................................................................31
Figures
Figure 1:
Figure 2:
Dimensions for Full Size 2.5-inch Drives...................................................................13
Layout of Signal and Power Segment Pins ................................................................14
Product Specification
4
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
1
Overview
The Intel® Solid-State Drive 535 Series is the next generation of Intel Solid-State Drive Consumer
Family which continue to deliver reliable performance and low power consumption with high quality.
The Intel SSD 535 Series is built for a wide range of consumer and embedded platforms. Along with a
variety of capacities, the Intel SSD 535 Series offers:
High I/O and Throughput Performance
Low Power Consumption
High Reliability
Advanced Encryption Standard (AES) 256-bit Encryption
End-to-End Data Protection
Data Compression
The Intel SSD 535 Series is aligned with the latest version of the Intel® SSD Toolbox for monitoring and
maintaining the health of the SSD. To find the latest version of Intel SSD Toolbox, and for more
information on the Intel SSD 535 Series, visit www.intel.com/ssd and click on the Consumer Family or
Resource Center links.
September 2015
332062-003US
Product Specification
5
Intel® Solid-State Drive 535 Series (2.5-inch)
1.1
Table 1:
Terms and Acronyms
Glossary of Terms and Acronyms
Term
Description
AHCI*
APM
Advanced Host Controller Interface
Advanced Power Management
ATA
Advanced Technology Attachment
Device Activity Signal
DAS
DevSleep
DIPM
DMA
Device Sleep
Device Initiated Power Management
Direct Memory Access
DPTF
eDrive
EXT
Dynamic Platform Thermal Framework
Microsoft* specification for a drive that complies to the TCG Opal 2.0 and IEEE 1667* standards
Extended
FPDMA
First Party Direct Memory Access
Gigabyte (1,000,000,000 bytes)
Note: The total usable capacity of the SSD may be less than the total physical capacity because a small
portion of the capacity is used for NAND flash management and maintenance purposes.
GB
HDD
HIPM
I/O
Hard Disk Drive
Host Initiated Power Management
Input/Output
IOPS
KB
Input/Output Operations Per Second
Kilobyte (1,024 bytes)
Logical Block Address
Link Power Management
Megabyte (1,000,000 bytes)
Multi-level Cell
LBA
LPM
MB
MLC
MTBF
NCQ
NOP
Mean Time Between Failures
Native Command Queuing
No Operation
PIO
Programmed Input/Output
PSID
RDT
Physical Security ID, public drive-unique value
Reliability Demonstration Test
Root Mean Squared
RMS
SATA
SED
Serial Advanced Technology Attachment
Self-Encrypting Drive
SMART
SSD
Self-Monitoring, Analysis and Reporting Technology
Solid-State Drive
TYP
Typical
UBER
Uncorrectable Bit Error Rate
Product Specification
6
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
1.2
Reference Documents
Table 2:
Standard References
Date or Rev. #
Title
Location
http://www.sffcommittee.org/
http://www.sffcommittee.org/
May 2005
May 2006
SFF-8201, 2.5-inch drive form factor
SFF-8223, 2.5-inch Drive w/Serial Attachment
Connector
IEC 55022 Information Technology Equipment —
Radio disturbance Characteristics— Limits and
methods of measurement CISPR22:2008 (Modified)
Sept 2008
Dec 2008
June 2009
http://www.iec.ch/
VCCI
http://www.vcci.jp/vcci_e/
http://qdms.intel.com/
Click Search MDDS Database and search
for material description datasheet
RoHS
IEC 55024 Information Technology Equipment —
Immunity characteristics— Limits and methods of
measurement CISPR24:2010
August 2010
Sept 2010
http://www.iec.ch/
Solid-State Drive (SSD) Requirements and
Endurance Test Method (JESD218)
http://www.jedec.org/standards-
documents/docs/jesd218/
August 2013
October 2013
Serial ATA Revision 3.2
ACS-3 Specification
http://www.sata-io.org/
http://www.t13.org/
September 2015
332062-003US
Product Specification
7
Intel® Solid-State Drive 535 Series (2.5-inch)
2
Product Specifications
2.1
Capacity
Table 3:
User Addressable Sectors
Capacity
Unformatted Capacity (Total User Addressable Sectors in LBA mode)
56GB
120GB
180GB
240GB
360GB
480GB
109,417,392
234,441,648
351,651,888
468,862,128
703,282,608
937,703,088
2.2
Performance
Table 4:
Compressible Performance
Specification
Random
4KB Read
(up to)1
Random
4KB Write
(up to)2
Random
4KB Write
(TYP)1
Sequential
Sequential
Capacity
128KB Read1
128KB Write1
IOPS
IOPS
IOPS
MB/s
540
540
540
MB/s
480
480
490
56GB
120GB
180GB
240GB
360GB
480GB
12,000
24,000
41,000
80,000
80,000
80,000
23,000
37,500
49,000
41,000
45,000
48,000
80,000
33,000
37,000
49,000
29,500
31,000
540
540
540
490
490
490
Note:
1.
Performance measured by Intel using IOMeter* with Queue Depth 32. Measurements are performed on 8 GB of
Logical Block Address (LBA) range on a full SSD.
2.
Random 4 KB writes measured using out-of-box SSD.
Table 5:
Incompressible Performance
Specification
Random
4KB Read
(up to)1
Random
4KB Write
(up to)1
Sequential
Sequential
Capacity
128KB Read1
128KB Write1
IOPS
IOPS
MB/s
400
450
470
510
525
540
MB/s
100
130
170
230
240
300
56GB
120GB
180GB
240GB
360GB
480GB
13,000
18,000
37,500
37,500
37,500
37,500
2,000
15,000
17,000
23,000
10,000
13,000
Note:
1.
Performance measured by Intel using IOMeter* with Queue Depth 32
Product Specification
8
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
Table 6: Latency
Specification
Intel SSD 535 Series (All Capacities)
Read1
80 µs (TYP)
85 µs (TYP)
500 ms (TYP)
<10 s
Write1
Power On To Ready2
Max Power On To Ready3
Note:
1.
Based on sequential 4KB using IOMeter with Queue Depth 1 workload with compressible (non-random) data
pattern. Write Cache enabled.
Power On To Ready time assumes safe shutdown
Max Power On To Ready time assumes unsafe shutdown. Based on statistical measurement of 95% quality of
service.
2.
3.
2.3
Electrical Characteristics
Table 7:
Operating Voltage and Power Consumption
Value
Electrical Characteristics
56GB
120GB
180GB
240GB
360GB
480GB
Operating Voltage for 5 V (±5%)
Min
4.75 V
5.25 V
Max
Rise Time (Max/Min)
Fall Time (Max/Min)
Noise Tolerance
Min Off Time1
100 ms / 0.1 ms
5 s / 1 ms
100 mV pp (10 Hz – 30 MHz)
1 s
Power Consumption (TYP)
Active2
Idle3
DevSleep4
165 mW
55 mW
5 mW
Thermal Power5
Regulator Power6
2.1 W
2.5 W
3.1 W
3.4 W
3.7 W
4.0 W
4.5 W
4.9 W
4.5 W
5.5 W
4.5 W
5.8 W
NOTES:
1.
2.
3.
4.
5.
Minimum time from when power removed from drive (Vcc < 100 mV) to when power can be reapplied to drive.
Active power measured during execution of MobileMark* 2007 with SATA Link Power Management (LPM) enabled.
Non-DevSleep idle power with SATA Link Power Management (LPM) enabled.
Power consumption during DevSleep state.
Power measured during 128kB sequential writes with Queue Depth 32 workload using 100 ms sample period. This
represents power that would be thermal load on system during heavy workloads.
6.
Power measured during 128kB sequential writes with Queue Depth 32 workload using 500 us sample period. This
represents power that system power supply would have to regulate for proper device operation.
September 2015
332062-003US
Product Specification
9
Intel® Solid-State Drive 535 Series (2.5-inch)
2.4
Environmental Conditions
2.4.1
Temperature, Shock, Vibration
Table 8:
Temperature, Shock, Vibration
Electrical Characteristics
Range
Case Temperature
Operating
0° C – 70° C
-55° C – 95° C
Non-operating1
Temperature Gradient2
Operating
30 (TYP)° C/hr
30 (TYP)° C/hr
Non-operating
Humidity
Operating
Non-operating
5 – 95 %
5 – 95 %
Shock and Vibration
Range
Shock3
Operating
Non-operating
Vibration4
1,500 G (Max) at 0.5 msec
1,500 G (Max) at 0.5 msec
Operating
Non-operating
2.17 GRMS (5-700 Hz) Max
3.13 RMS (5-800 Hz) Max
NOTES:
1.
Please contact your Intel representative for details on the non-operating temperature range.
Temperature gradient measured without condensation.
Shock specifications assume SSD is mounted securely with the input vibration applied to the drive-mounting
screws. Stimulus may be applied in the X, Y or Z axis. Shock specification is measured using peak acceleration and
pulse width value.
2.
3.
4.
Vibration specifications assume the SSD is mounted securely with the input vibration applied to the drive-mounting
screws. Stimulus may be applied in the X, Y or Z axis. Vibration specification is measured using G Root Mean
Squared (GRMS) value.
2.4.2
Altitude
The drive is not sensitive to changes in atmospheric pressure because it has no moving parts. Drive tested under
non-operational conditions to pressures representative of -1 K and +40 K feet.
Product Specification
10
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
2.5
Product Regulatory Compliance
The Intel SSD 535 Series meets or exceeds the regulatory or certification requirements in the table below.
Table 9:
Product Regulatory Compliance Specifications
Title
Region For Which
Description
Conformity Declared
TITLE 47-Telecommunications CHAPTER 1—
FEDERAL COMMUNMICATIONS COMMISSION
PART 15 — RADIO FREQUENCY DEVICES
FCC Part 15B Class B
USA
ICES-003, Issue 4 Interference-Causing
Equipment
Standard Digital Apparatus
CAN/CSA – CEI/IEC CISPR 22-10 (Ref. CISPR
22:2008)
Canada
IEC 55024 Information Technology Equipment
— Immunity characteristics— Limits and
methods of measurement CISPR24:2010
EN-55024: 2010 and its amendments
EN-55022: 2010 and its amendments
European Union
IEC 55022 Information Technology Equipment
— Radio disturbance Characteristics— Limits
and methods of measurement CISPR22:2008
(Modified)
European Union
Information Technology Equipment — Safety —
Part 1: General Requirements
EN-60950-1 2nd Edition
USA/Canada
USA/Canada
Information Technology Equipment — Safety —
Part 1: General Requirements
UL/CSA EN-60950-1 2nd Edition
September 2015
332062-003US
Product Specification
11
Intel® Solid-State Drive 535 Series (2.5-inch)
2.6
Reliability
The Intel SSD 535 Series meets or exceeds SSD endurance and data retention requirements as specified in the
JESD218 specification.
Table 10: Reliability Specifications
Parameter
Value
Uncorrectable Bit Error Rate (UBER)
Uncorrectable bit error rate will not exceed one sector in the specified number of bits
read. In the unlikely event of a non-recoverable read error, the SSD will report it as a
read failure to the host; the sector in error is considered corrupt and is not returned to
the host.
< 1 sector per 1016 bits read
Mean Time Between Failures (MTBF)
Mean Time Between Failures is estimated based on Telcordia* methodology and
demonstrated through Reliability Demonstration Test (RDT).
≥ 1.2 million hours
Minimum Useful Life/Endurance Rating
The SSD will have a minimum of five years of useful life under client workloads with up
to 40 GB† of host writes per day.
5 years
Insertion Cycles
250 insertion/removal cycles
Maximum insertion/removal cycles on 2.5-inch port
†56GB and 120GB SSD qualified to 20GB of host writes per day.
2.7
Hot Plug Support
Hot Plug insertion and removal is supported in the presence of a proper connector and appropriate operation
system, as described in the SATA 3.2 specification.
This product supports asynchronous signal recovery and issues an unsolicited COMINIT when first mated with a
powered connector to enable detection by a host system without hardware device detection.
Product Specification
12
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
3
Mechanical Information
The figure below shows the mechanical information for the full size 2.5-inch Intel SSD 535 Series. All dimensions
are in millimeters.
Figure 1: Dimensions for Full Size 2.5-inch Drives
September 2015
332062-003US
Product Specification
13
Intel® Solid-State Drive 535 Series (2.5-inch)
4
Pin and Signal Descriptions
4.1
Pin Locations
Figure 2: Layout of Signal and Power Segment Pins
4.2
Signal Descriptions
4.2.1
Connector Pin Signal Definitions
Table 11: Serial ATA Connector Pin Definitions
Pin
S1
S2
S3
S4
S5
S6
S7
Function
Ground
A+
Definition
1st mate
Differential signal pair A
1st mate
A-
Ground
B-
Differential signal pair B
1st mate
B+
Ground
Note:
Key and spacing separate signal and power segments.
Product Specification
14
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
4.2.2
Power Pin Signal Definitions
Table 12: Serial ATA Power Pin Definitions
Pin1
Name
Definition
3.3 V Power; not used
Mating Order
P12
P22
2nd Mate
2nd Mate
1st Mate
1st Mate
1st Mate
1st Mate
1st Mate
2nd Mate
2nd Mate
1st Mate
2nd Mate
1st Mate
1st Mate
2nd Mate
2nd Mate
V33
V33
3.3 V Power; not used
Device Sleep Pin
DevSleep
Ground
Ground
Ground
V5
P3
P43,4
P53
P63
P73,5
P83,5
P93,5
P103
P116
P123, 4
P132
P142
P152
5 V Power
5 V Power
5 V Power
V5
V5
Ground
DAS
Device Activity Signal
Ground
V12
12 V Power; not used
12 V Power; not used
12 V Power; not used
V12
V12
NOTES:
1.
All pins are in a single row, with a 1.27 mm (0.050-inch) pitch.
2.
Pins P1 and P2 are connected together; Pins P13, P14 and P15 are connected together. Although they are not
connected internally to the device, the host may apply voltage on these pins.
The mating sequence is:
- Ground pins P4-P6, P10, P12 and the 5V power pin P7.
- Signal pins and the rest of the 5V power pins P8-P9.
Ground connectors P4 and P12 may contact before the other 1st mate pins in both the power and signal connectors
to discharge ESD in a suitably configured backplane connector.
3.
4.
5.
6.
Power pins P7, P8, and P9 are internally connected to one another within the device.
The host may ground P11 if it is not used for Device Activity Signal (DAS).
4.3
Device Sleep Feature
Device Sleep (or DevSleep/DEVSLP) is the latest feature aligned with Intel® 4th Generation Core™-based
Ultrabook™. Ultrabook™ has stringent power requirements for SSDs and as such requires an ability to put the drive
in a low power state. Although Link Power Management allows some control over power consumption, both
methods still require the SATA link to remain online. The DevSleep pin is an “Enable” (High) pin which is pulled up
by the drive.
September 2015
332062-003US
Product Specification
15
Intel® Solid-State Drive 535 Series (2.5-inch)
5
Supported Command and Feature Sets
The Intel SSD 535 Series supports all mandatory Advanced Technology Attachment (ATA) and Serial ATA (SATA)
commands defined in the ACS-3 and SATA Revision 3.2 specifications. The mandatory and optional commands are
defined in this section.
5.1
Supported ATA General Feature Command Set
Below are mandatory and optional ATA feature sets supported by Intel SSD 535 Series.
48-Bit Address
Advanced Power Management (APM)
General
General Purpose Logging (GPL)
Native Command Queuing (NCQ)
Power Management
Sanitize Device
Security
SMART
Software Settings Preservation (SSP)
Below are mandatory and optional ATA commands supported by Intel SSD 535 Series.
Table 13: Supported ATA Commands and Feature Sets
Commands
Feature Set
BLOCK ERASE EXT
CHECK POWER MODE
CRYPTO SCRAMBLE EXT
DATA SET MANAGEMENT
DOWNLOAD MICROCODE
EXECUTE DEVICE DIAGNOSTIC
FLUSH CACHE
Sanitize Device
Power Management
Sanitize Device
ATA General Feature
ATA General Feature
ATA General Feature
ATA General Feature
48-Bit Address
FLUSH CACHE EXT
IDENTIFY DEVICE 1
ATA General Feature
IDLE
Power Management
Power Management
ATA General Feature
ATA General Feature
ATA General Feature
48-Bit Address
IDLE IMMEDIATE
NOP
READ BUFFER
READ DMA
READ DMA EXT
Product Specification
16
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
Commands
Feature Set
READ FPDMA QUEUED
Native Command Queuing
General Purpose Logging
General Purpose Logging
ATA General Feature
48-Bit Address
48-Bit Address
48-Bit Address
ATA General Feature
48-Bit Address
ATA General Feature
48-Bit Address
Sanitize Device
Sanitize Device
ATA Security
READ LOG DMA EXT
READ LOG EXT
READ MULTIPLE
READ MULTIPLE EXT
READ NATIVE MAX ADDRESS
READ NATIVE MAX ADDRESS EXT
READ SECTOR(S)
READ SECTOR(S) EXT
READ VERIFY SECTOR(S)
READ VERIFY SECTOR(S) EXT
SANITIZE FREEZE LOCK EXT
SANITIZE STATUS EXT
SECURITY DISABLE PASSWORD
SECURITY ERASE PREPARE
SECURITY ERASE UNIT
ATA Security
ATA Security
SECURITY FREEZE LOCK
SECURITY SET PASSWORD
SECURITY UNLOCK
ATA Security
ATA Security
ATA Security
SEEK
ATA General Feature
ATA General Feature
48-Bit Address
ATA General Feature
Power Management
SMART
SET FEATURES
SET MAX ADDRESS EXT
SET MULTIPLE MODE
SLEEP
SMART DISABLE OPERATIONS
SMART ENABLE OPERATIONS
SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
SMART EXECUTE OFF-LINE IMMEDIATE
SMART READ DATA
SMART
SMART
SMART
SMART
SMART READ ATTRIBUTE THRESHOLDS
SMART READ LOG
SMART
SMART
SMART READ LOG SECTOR
SMART RETURN STATUS
SMART SAVE ATTRIBUTE VALUES
SMART
SMART
SMART
September 2015
332062-003US
Product Specification
17
Intel® Solid-State Drive 535 Series (2.5-inch)
Commands
SMART WRITE LOG SECTOR
STANDBY
Feature Set
SMART
Power Management
Power Management
ATA General Feature
ATA General Feature
48-Bit Address
STANDBY IMMEDIATE
WRITE BUFFER
WRITE DMA
WRITE DMA EXT
WRITE DMA FUA EXT
WRITE FPDMA QUEUED
WRITE LOG DMA EXT
WRITE LOG EXT
48-Bit Address
Native Command Queuing
General Purpose Logging
General Purpose Logging
ATA General Feature
48-Bit Address
WRITE MULTIPLE
WRITE MULTIPLE EXT
WRITE MULTIPLE FUA EXT
WRITE SECTOR(S)
48-Bit Address
ATA General Feature
48-Bit Address
WRITE SECTOR(S) EXT
WRITE UNCORRECTABLE EXT
ATA General Feature
NOTES:
1.
See the Appendix for details on the sector data returned after issuing an IDENTIFY DEVICE command.
Product Specification
18
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
5.2
Advanced Power Management (APM)
The Advanced Power Management can be enabled or disabled using the SET FEATURES command.
Table 14: APM Subcommand Codes for Power Management and Definitions
Subcommand Codes
Definition
10h
40h
80h
FEh
Power optimized for connected standby power
Power optimized for lid up
Balanced power/performance for non-connected standby
Optimized for high performance (Default)
Table 15: APM Subcommand Codes for Thermal Power Management and Definitions
Subcommand Codes
Definition
60h
6Fh
Most aggressive thermal setting
Light thermal setting
5.3
Security
5.3.1
Sanitization Methods
Sanitization refers to a process to render data inaccessible. Various sanitization methods are listed below.
5.3.1.1
Secure Erase
Secure Erase runs the SECURITY ERASE UNIT command
Table 16: Supported Secure Erase Modes and Definitions
Secure Erase Mode
Definition
Normal Mode
Full NAND erase of user available space and spare area
Cryptographically erase data
Enhanced Mode
5.3.1.2
Sanitize Device
Table 17: Supported Sanitize Device Modes and Definitions
Mode
Definition
Block erase method, all user data areas including user data not currently
allocated, irretrievable
Block Erase
Crypto Scramble Ext
Changes the internal encryption keys
5.4
Device Statistics
In addition to the SMART attribute structure, statistics pertaining to the operation and health of the Intel SSD 535
Series can be reported to the host on request through the Device Statistics log as defined in the ATA specification.
The Device Statistics log is a read-only GPL/SMART log located at read log address 0x04 and is accessible using
READ LOG EXT, READ LOG DMA EXT or SMART READ LOG commands.
The following table lists the Device Statistics supported by the Intel SSD 535 Series.
September 2015
332062-003US
Product Specification
19
Intel® Solid-State Drive 535 Series (2.5-inch)
Table 18: Device Statistics Log
Page Offset
Equivalent SMART attribute
if applicable
Description
0x00
-
List of Supported Pages
Power Cycle Count
Power-On Hours
-
0x08
0x10
0x18
0x28
0Ch
09h
E1h
F2h
0x01 - General
Statistics
Logical Sectors Written
Logical Sectors Read
Num Reported Uncorrectable
Errors
0x08
0x10
BBh
-
0x04 - General
Errors Statistics
Num Resets Between Command
Acceptance and Completion
0x08
0x10
0x18
Num Hardware Resets
Num ASR Events
-
0x06 - Transport
Statistics
-
Num Interface CRC Errors
-
E9h
0x07 - Solid State
Device Statistics
Percentage Used Endurance
Indicator
This statistic counts up from 0 rather than
down from 100, and may go beyond 100 for
drives that exceed their expected lifetime.
0x08
5.5
Software Settings Preservation
Intel SSD 535 Series supports the SET FEATURES parameter to enable/disable the preservation of software
settings. The following table lists the software setting that will be preserved across a COMRESET.
Table 19: Preserved Software Settings
Feature
Preserved Settings
Advanced Power Management
Multiple Mode
Enabled or Disabled
Block size from the last set multiple mode
NCQ Streaming commands
processing
WDNC bit and RDNC bit states
Password Attempt Counter
Read look-ahead
Password Attempt Counter value
Enabled or Disabled
Read/Write Stream Error Logs
Reverting to defaults mode
Sanitize Device
Log contents
Enabled or disabled
Whether device is in the Sanitize Frozen state
Current Security state
Security
Standby Timer
Standby Timer setting
Transfer Mode
DMA and UDMA transfer mode settings
Enabled or Disabled
Volatile Write Cache
Write-Read-Verify feature set settings. Device shall not return to factory
default Write-Read-Verify settings after a COMRESET
Write-Read Verify
Product Specification
20
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
5.6
DevSleep
Intel SSD 535 Series supports the DevSleep feature. DevSleep must be enabled on the device by the
host system through the SET FEATURES command. If DevSleep is enabled by the host, the host must drive
the DevSleep signal to proper assert/de-assert voltage levels according to the SATA specification. Entry into
DevSleep must be preceded by LPM slumber entry by host and device. The Intel SSD 535 Series also supports
DevSleep_to_ReducedPwrState which allows the host to wake the drive using normal LPM COMWAKE
out-of-band signaling.
For the Intel SSD 535 Series, the recommended total time to DevSleep for system active state is 6 sec.
The AHCI* controller has 4 parameters used to define proper DevSleep operation between the host and drive.
The following table provides those recommended values for the Intel SSD 535 Series drive.
Table 20: DevSleep Control Parameters
Recommended
Parameter
Definition
Control
Settings
DevSleep Idle Time Out – number of
milliseconds prior to host asserting
DevSleep
Set by Host
Active (lid-up): 375
DITO
DM
DITO Multiplier – set once at boot-up
Set by Host
15
10
Minimum DevSleep Assertion Time –
minimum time in milliseconds for host to
assert DevSleep
Reported by Drive
MDAT
DevSleep Exit Time Out – max time in
milliseconds from when DevSleep is
negated to when device ready to detect
OOB
Reported by Drive
20
DETO
Total time to DevSleep entry = DITO * (DM+1)
5.7
SMART Command Transport
With SMART Command Transport (SCT), a host can send commands and data to an SSD and receive status
and data from an SSD using standard write/read commands to manipulate two SMART Logs:
Log Address E0h ("SCT Command/Status") — used to send commands and retrieve status
Log Address E1h ("SCT Data Transfer") — used to transport data
September 2015
332062-003US
Product Specification
21
Intel® Solid-State Drive 535 Series (2.5-inch)
5.8
SMART Attributes
The following two tables list the SMART attributes supported by the Intel SSD 535 Series, and the
corresponding status flags and threshold settings.
Table 21: SMART Attributes
Status Flags
ID
Attribute
Threshold
SP
EC
ER
PE
OC
PW
Re-allocated Sector Count
The raw value of this attribute shows the
number of retired blocks since leaving the
factory (grown defect count).
05h
1
1
0
0
1
0
0 (none)
Power-On Hours Count
The raw value reports two values: the first
4 bytes report the cumulative number of
power-on hours over the life of the device,
the remaining bytes report the number of
milliseconds since the last hour increment.
The On/Off status of the Device Initiated
Power Management (DIPM) feature will
affect the number of hours reported. If DIPM
is turned On, the recorded value for
power-on hours does not include the time
that the device is in a "slumber" state. If
DIPM is turned Off, the recorded value for
power-on hours should match the clock
time, as all three device states are counted:
active, idle and slumber.
09h
1
1
0
0
1
0
0 (none)
Power Cycle Count
The raw value of this attribute reports the
cumulative number of power cycle events
over the life of the device.
0Ch
1
1
1
1
0
0
0
0
1
1
0
1
0 (none)
10
AAh Available Reserved Space
Program Fail Count
The raw value of this attribute shows total
ABh
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
0 (none)
count of program fails and the normalized
value, beginning at 100, shows the percent
remaining of allowable program fails.
Erase Fail Count
The raw value of this attribute shows total
count of erase fails and the normalized
value, beginning at 100, shows the percent
remaining of allowable erase fails.
ACh
Unexpected Power Loss
The raw value of this attribute reports the
cumulative number of unsafe (unclean)
shutdown events over the life of the device.
An unsafe shutdown occurs whenever the
device is powered off without STANDBY
IMMEDIATE being the last command
AEh
B7h
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
SATA Downshift Count
0
The count of the number of times
SATAinterface selected lower signaling rate
Product Specification
22
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
Status Flags
ID
Attribute
Threshold
SP
EC
ER
PE
OC
PW
dueto error.
End-to-End Error Detection Count
Reports number of errors encountered during
end-to-end error detection within the SSD
data path.
B8h
BBh
1
1
1
1
0
0
0
0
1
1
1
0
90
Uncorrectable Error Count
The raw value shows the count of errors that
could not be recovered using Error
Correction Code (ECC).
0 (none)
Temperature
Reports real-time temperature of drive as
measured by temperature sensor on drive
PCB. The normalized value reports the
current temperature value. The raw value
shows current, lifetime highest and lifetime
lowest temperatures. Byte 1:0 = current
temp Celsius; Byte 3:2 = lifetime highest
temp Celsius; Byte 5:4 = lifetime lowest
temp Celsius.
BEh
1
1
0
0
1
0
0 (none)
Power-Off Retract Count (Unsafe Shutdown
Count)
The raw value of this attribute reports the
cumulative number of unsafe (unclean)
shutdown events over the life of the device.
An unsafe shutdown occurs whenever the
device is powered off without STANDBY
IMMEDIATE being the last command.
C0h
1
1
0
0
1
0
0 (none)
CRC Error Count
The total number of encountered SATA
interface cyclic redundancy check (CRC)
errors.
C7h
E1h
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
0 (none)
Host Writes
The raw value of this attribute reports the
total number of sectors written by the host
system. The raw value is increased by 1 for
every 65,536 sectors (32MB) written by the
host.
Timed Workload Media Wear
Measures the wear seen by the SSD (since
reset of the workload timer, attribute E4h),
as a percentage of the maximum rated
cycles.
E2h
E3h
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
0 (none)
Timed Workload Host Read/Write Ratio
Shows the percentage of I/O operations that
are read operations (since reset of the
workload timer, attribute E4h).
Timed Workload Timer
E4h
E8h
1
1
1
1
0
0
0
0
1
1
0
1
0 (none)
10
Measures the elapsed time (number of
minutes since starting this workload timer).
Available Reserved Space
This attribute reports the number of reserve
September 2015
332062-003US
Product Specification
23
Intel® Solid-State Drive 535 Series (2.5-inch)
Status Flags
ID
Attribute
Threshold
SP
EC
ER
PE
OC
PW
blocks remaining. The normalized value
begins at 100 (64h), which corresponds to
100 percent availability of the reserved
space. The threshold value for this attribute
is 10 percent availability.
Media Wearout Indicator
This attribute reports the number of cycles
the NAND media has undergone. The
normalized value declines linearly from 100
to 1 as the average erase cycle count
increases from 0 to the maximum rated
cycles. Once the normalized value reaches 1,
the number will not decrease, although it is
likely that significant additional wear can be
put on the device
E9h
F1h
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
0 (none)
Total LBAs Written
The raw value of this attribute reports the
total number of sectors written by the host
system. The raw value is increased by 1 for
every 65,536 sectors (32MB) written by the
host.
Total LBAs Read
The raw value of this attribute reports the
total number of sectors read by the host
system. The raw value is increased by 1 for
every 65,536 sectors (32MB) read by the
host.
F2h
F9h
1
1
1
1
0
0
0
0
1
1
0
0
0 (none)
0 (none)
Total NAND Writes
Raw value reports the number of writes to
NAND in 1 GB increments.
Table 22: SMART Attribute Status Flags
Status Flag
Description
Value = 0
Value = 1
SP
EC
ER
PE
Self-preserving attribute
Event count attribute
Error rate attribute
Not a self-preserving attribute
Not an event count attribute
Not an error rate attribute
Not a performance attribute
Self-preserving attribute
Event count attribute
Error rate attribute
Performance attribute
Performance attribute
Collected only during offline
activity
Collected during both offline
and online activity
OC
Online collection attribute
Pre-fail warranty attribute
PW
Advisory
Pre-fail
5.9
SMART Logs
Intel SSD 535 Series implements the following Log Addresses: 00h, 02h, 03h, 06h, and 07h.
The Intel SSD 535 Series implements host vendor specific logs (addresses 80h-9Fh) as read and write scratchpads,
where the default value is zero (0). Intel SSD 535 Series does not write any specific values to these logs unless
directed by the host through the appropriate commands.
Product Specification
24
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
The Intel SSD 535 Series also implements a device vendor specific log at address A9h as a read-only log area with
a default value of zero (0).
September 2015
332062-003US
Product Specification
25
Intel® Solid-State Drive 535 Series (2.5-inch)
6
Certifications and Declarations
The following table describes the Device Certifications supported by the Intel SSD 535 Series.
Table 23: Device Certifications and Declarations
Certification
Description
European Economic Area (EEA): Compliance with the essential requirements of EC Council
Directives Low Voltage Directive (LVD) 2006/95/EC, EMC Directive 2004/108/EC and Directive
2011/65/EU.
CE* Compliant
Certified Underwriters Laboratories, Inc. Bi-National Component Recognition; UL 60950-1, 2nd
Edition, 2007-03-27 (Information Technology Equipment - Safety - Part 1: General
Requirements)
UL* Certified
CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03 (Information Technology Equipment - Safety -
Part 1: General Requirements)
Compliance with the Australia/New Zealand Standard AS/NZS3548 and Electromagnetic
Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
C-Tick* Compliant
BSMI* Compliant
Compliance to the Taiwan EMC standard CNS 13438: Information technology equipment - Radio
disturbance Characteristics - limits and methods of measurement, as amended on June 1, 2006,
is harmonized with CISPR 22: 2005.04.
Compliance with paragraph 1 of Article 11 of the Electromagnetic Compatibility Control
Regulation and meets the Electromagnetic Compatibility (EMC) Framework requirements of the
Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea.
KCC*
Microsoft WHCK*
RoHS* Compliant
Microsoft Windows Hardware Certification Kit
Restriction of Hazardous Substance Directive
Voluntary Control Council for Interface to cope with disturbance problems caused by personal
computers or facsimile.
VCCI*
SATA-IO*
Indicates certified logo program from Serial ATA International Organization.
Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final
product. Intel components as well as purchased components on the finished assembly meet JS-
709 requirements, and the PCB/substrate meet IEC 61249-2-21 requirements. The replacement
of halogenated flame retardants and/or PVC may not be better for the environment.
Low Halogen
Product Specification
26
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
7
Appendix
7.1
Identify Device
The table below describes the sector data returned from an identify device command
Table 24: Identify Device Returned Sector Data
F = Fixed
Word
V = Variable
X = Both
Default Value
Description
0
1
F
X
V
X
X
X
V
X
F
0040h
3FFFh
C837h
0010h
0h
General configuration bit-significant information
Obsolete - Number of logical cylinders (16,383)
Specific configuration
2
3
Obsolete - Number of logical heads (16)
Retired
4-5
6
003Fh
0h
Obsolete - Number of logical sectors per logical track (63)
Reserved for assignment by the CompactFlash* Association (CFA)
Retired
7-8
9
0h
10-19
20-21
22
varies
0h
Serial number (20 ASCII characters)
Retired
X
X
F
0h
Obsolete
23-26
27-46
varies
varies
Firmware revision (8 ASCII characters)
Model number (Intel Solid-State Drive)
F
7:0—Maximum number of sectors transferred per interrupt on
multiple commands
47
F
8010h
48
49
F
F
4000h
2F00h
4000h
0h
Reserved
Capabilities
50
F
Capabilities
51-52
53
X
F
Obsolete
0007h
3FFFh
Words 88 and 70:64 valid
54
X
X
X
X
V
Obsolete - Number of logical cylinders (16,383)
Obsolete - Number of logical heads (16)
Obsolete - Number of logical sectors per logical track (63)
Obsolete
55
0010h
003Fh
00FBFC10h
B110h
56
57-58
59
Number of sectors transferred per interrupt on multiple commands
September 2015
332062-003US
Product Specification
27
Intel® Solid-State Drive 535 Series (2.5-inch)
F = Fixed
V = Variable
X = Both
Word
Default Value
Description
60-61
62
63
64
65
66
67
68
69
70
71-74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
F
X
F
F
F
F
F
F
F
F
F
F
F
F
F
V
F
F
F
F
F
V
V
V
V
F
F
V
V
varies
0h
Total number of user-addressable sectors
Obsolete
0007h
0003h
0078h
0078h
0078h
0078h
4010h
0h
Multi-word DMA modes supported/selected
PIO modes supported
Minimum multiword DMA transfer cycle time per word
Manufacturer’s recommended multiword DMA transfer cycle time
Minimum PIO transfer cycle time without flow control
Minimum PIO transfer cycle time with IORDY flow control
Additional Supported
Reserved
0h
Reserved for IDENTIFY PACKET DEVICE command
Queue depth
001Fh
070Eh
0086h
014Ch
0044h
07FCh
FFFFh
746Bh
7429h
6163h
7469h
B409h
6163h
407Fh
0002h
0001h
00FEh
FFFEh
Serial ATA capabilities
Reserved for future Serial ATA definition
Serial ATA features supported
Serial ATA features enabled
Major version number
Minor version number
Command set supported
Command sets supported
Command set/feature supported extension
Command set/feature enabled
Command set/feature enabled
Command set/feature default
Ultra DMA Modes
Time required for security erase unit completion
Time required for enhanced security erase completion
Current advanced power management value
Master Password Revision Code
Hardware reset result: the contents of bits (12:0) of this word shall
change only during the execution of a hardware reset
93
F
0h
Product Specification
28
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
F = Fixed
V = Variable
X = Both
Word
Default Value
Description
94
95
V
F
V
V
F
V
V
F
F
F
F
F
V
F
F
F
F
F
V
X
F
X
X
F
F
V
X
X
X
X
X
0h
0h
Vendor’s recommended and actual acoustic management value
Stream minimum request size
96
0h
Streaming transfer time - DMA
Streaming access latency - DMA and PIO
Streaming performance granularity
Maximum user LBA for 48-bit address feature set
Streaming transfer time - PIO
97
0h
98-99
100-103
104
0h
varies
0h
105
0001h
4000h
0h
Reserved
106
Physical sector size / logical sector size
Inter-seek delay for ISO-7779 acoustic testing in microseconds
Unique ID
107
108-111
112-115
116
varies
0h
Reserved for world wide name extension to 128 bits
Reserved for technical report
0h
117-118
119
0h
Words per logical sector
401Ch
401Ch
0h
Supported settings
120
Command set/feature enabled/supported
Reserved
121-126
127
0h
Removable Media Status Notification feature set support
Security status
128
0021h
varies
0h
129-159
160
Vendor-specific
CompactFlash Association (CFA) power mode 1
Reserved for assignment by the CFA
Data set management Trim attribute support
Additional Product Identifier
161-168
169
0h
0001h
0h
170-173
174-175
176-205
206
0h
Reserved
0h
Current media serial number
0025h
0h
SCT Command Transport
207-208
209
Reserved
4000h
0h
Alignment of logical blocks within a physical block
Write-Read-Verify Sector Count Mode 3 (DWord)
Write-Read-Verify Sector Count Mode 2 (DWord)
210-211
212-213
0h
September 2015
332062-003US
Product Specification
29
Intel® Solid-State Drive 535 Series (2.5-inch)
F = Fixed
V = Variable
X = Both
Word
Default Value
Description
214
215-216
217
X
X
X
X
X
X
X
X
X
X
X
0h
0h
NV Cache Capabilities
NV Cache Size in Logical Blocks (DWord)
Nominal media rotation rate
Reserved
0001h
0h
218
219
0h
NV Cache Options
220
0h
Write-Read-Verify feature set
Reserved
221
0h
222
10FFh
0h
Transport major version number
Transport minor version number
Reserved
223
224-229
230-233
0h
0h
Extended Number of User Addressable Sectors (QWord)
Minimum number of 512-byte data blocks per DOWNLOAD
MICROCODE command for mode 03h
234
235
X
X
0002h
0400h
Maximum number of 512-byte data blocks per DOWNLOAD
MICROCODE command for mode 03h
236-254
255
X
X
0h
Reserved
varies
Integrity word
Note:
F = Fixed. The content of the word is fixed and does not change. For removable media devices, these values may change
when media is removed or changed.
V = Variable. The state of at least one bit in a word is variable and may change depending on the state of the device or the
commands executed by the device.
X = F or V. The content of the word may be fixed or variable.
Product Specification
30
September 2015
332062-003US
Intel® Solid-State Drive 535 Series (2.5-inch)
7.2
Models
The following table lists the available 2.5-inch models of the Intel SSD 535 Series.
Table 25: Available Models
Model String
Capacity
SSDSC2BW056H6
SSDSC2BW120H6
SSDSC2BW180H6
SSDSC2BW240H6
SSDSC2BW360H6
SSDSC2BW480H6
56GB
120GB
180GB
240GB
360GB
480GB
September 2015
332062-003US
Product Specification
31
相关型号:
©2020 ICPDF网 联系我们和版权申明