MGH2812DZ/883 概述
Analog Circuit,
MGH2812DZ/883 数据手册
通过下载MGH2812DZ/883数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载FEATURES
• –55° to +125°C operation
MGH SERIES
1.5 WATT
DC/DC CONVERTERS
28 VOLT NPUT
• 12 to 50 VDC input
• Fully Isolated
I
• Magnetic feedback
MODELS
VDC OUTPUT
• Fixed frequency 370 kHz typical
• Topology – Current Mode Flyback
• 80 V for up to 120 ms transient protection
(70 V for 15 V single and dual models)
• Inhibit function
SINGLE
DUAL
±5
5
12
15
±12
±15
• Indefinite short circuit protection
• Up to 79% efficiency
Size (max.): 1.010 x 0.880 x 0.250 inches (25.65 x 22.35 x 6.35 mm)
Shown with “Gull Wing” lead option, also available with straight
leads. See Section B8, case B, for dimensions and options.
12 grams maximum
Weight:
Screening: Standard, ES, or 883 (Class H). See Section C2 for
screening options, see Section A5 for ordering information.
DESCRIPTION
The MGH Series™ of DC/DC converters delivers 1.5 watts of output
power in a labor saving surface mount package. The wide input
voltage range of 12 to 50 VDC accepts the varying voltages of mili-
tary, aerospace, or space applications. Single output converters
feature outputs of 5, 12, or 15 volts while dual output models feature
outputs of ±5, ±12, or ±15 volts. Transient protection of 80 volts for
up to 120 milliseconds exceeds the requirements of MIL-STD-704A
for the 5 and 12 volt single and dual models. The 15 volt single and
dual converters will withstand transients of up to 70 volts for up to
120 milliseconds.
PROTECTION FEATURES
Undervoltage lockout prevents the MGH Series converters from
operating below approximately 8 VDC input voltage to keep system
current levels smooth, especially during initialization or re-start oper-
ations. All models include a soft-start function to prevent large
current draw and minimize overshoot. The MGH Series of
converters also provide short circuit protection by limiting the current
to approximately 125% of full load.
MIL-STD-461
Use Interpoint’s FMGA-461 EMI filter to pass the CE03 require-
ments of MIL-STD-461C.
CONVERTER DESIGN
MGH Series DC/DC converters incorporate a continuous flyback
topology with a constant switching frequency of approximately 370
kHz. Output voltage regulation is accomplished on the primary side
using current-mode pulse width modulation (PWM). Regulation is
affected by the output load; refer to the specifications tables for
more information.
SURFACE MOUNT PACKAGE
MGH DC/DC converters can be surface mounted with pick-and-
place equipment or manually. It is recommended that the case be
attached with flexible epoxy adhesive or silicone which is thermally
conductive (>1 watt /meter/°K).
For dual output models, up to 80% of the total load may be on one
output providing the other output carries a minimum of 20% of the
total load. The dual models can be used at double the output voltage
by connecting the load between positive and negative outputs,
leaving the common unconnected. As an example the MGH2805D
(5 volt dual output) can be used as a 10 VDC output.
Internal components are soldered with SN96 (melting temperature
221°C) to prevent damage during reflow. Maximum reflow tempera-
ture for surface mounting the MGH converter is 220°C for a
maximum of 30 seconds. SN60, 62, or 63 are the recommended
types of solder. Hand soldering should not exceed 300°C for 10
seconds per pin.
INHIBIT FUNCTION
The hermetically sealed metal cases are available in two different
lead configurations. See Section B8, case B.
When an open collector TTL logic low is applied to the inhibit
terminal, pin 18, the converter shuts down and lowers the output
voltage to near zero and input current to as low 2.3 mA. Leaving the
terminal open or applying an open collector TTL logic high will
enable the converter.
B2-93
MGH SERIES
DC/DC CONVERTERS
1.5 WATT
ABSOLUTE MAXIMUM RATINGS
INHIBIT
TYPICAL CHARACTERISTICS
Inhibit:TTL Open Collector
• Logic low (output disabled)
Logic low voltage ≤0.8 V
Inhibit pin current 1 mA max
• Referenced to input common
• Logic high (output enabled) open collector
Input Voltage
• 12 to 50 V
Output Power
• 1.5 watts
Output Voltage Temperature Coefficient
• 100 ppm/°C typical
Input to Output Capacitance
• 100 to 170 pF typical
Undervoltage Lockout
• 8 V input typical
Current Limit
• 125% of full load typical
Isolation
• 100 megohm minimum at 500 V
Conversion Frequency (kHz)
• 25°C
300 min, 370 typ, 450 max
• –55°C to +125°C
Capacitive Load
• 200 µF single output models
• 100 µF each output, dual output models
Lead Soldering Temperature
• Reflow 220°C 30 sec. max
SN60, 62 or 63 recommended solder
• Hand solder 300°C 10 sec. max per lead
Storage Temperature Range (Case)
• –65°C to +150°C
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range
• 12 to 50 VDC continuous
•
80 V for 120 msec transient
(70 V for 15 V single and dual models)
Case Operating Temperature (Tc)
• –55°C to +125°C full power
270 min, 370 typ, 470 max
Inhibit Pin Voltage (unit enabled)
• 7 to 12 V
• –55°C to +135°C absolute
Derating Output Power/Current
• Linearly from 100% at 125C° to 0% at 135 C
Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
SINGLE OUTPUT MODELS
PARAMETER
OUTPUT VOLTAGE
MGH2805S
MGH2812S
MGH2815S
CONDITIONS
Tc = 25°C
Tc = –55°C TO +125°C
MIN
4.95
4.80
TYP
5
5
MAX
5.05
5.20
MIN
11.88
11.52
TYP
12
12
MAX
12.12
12.48
MIN
14.85
14.40
TYP
15
15
MAX
15.15
15.60
UNITS
1
VDC
OUTPUT CURRENT
OUTPUT POWER
V
V
= 12 to 50 VDC
= 12 to 50 VDC
0
0
—
—
300
1.5
0
0
—
—
125
1.5
0
0
—
—
100
1.5
mA
W
IN
IN
OUTPUT RIPPLE
VOLTAGE
10 kHz - 2 MHz
Tc = –55°C TO +125°C
—
—
45
65
150
300
—
—
50
70
200
300
—
—
35
50
150
250
mV p-p
mV
LINE REGULATION
VIN = 12 to 50 VDC
Tc = –55°C TO +125°C
—
—
35
40
100
120
—
—
60
70
200
250
—
—
70
80
300
350
LOAD REGULATION
10% TO FULL LOAD
Tc = –55°C TO +125°C
—
—
350
380
700
800
—
—
600
640
1300
1400
—
—
700
760
1500
1600
mV
50% TO FULL LOAD
Tc = –55°C TO +125°C
—
—
100
115
200
300
—
—
145
160
300
400
—
—
165
185
350
450
INPUT VOLTAGE
NO LOAD TO FULL
CONTINUOUS
TRANSIENT 120 ms
12
0
28
—
50
80
12
0
28
—
50
80
12
0
28
—
50
70
VDC
V
INPUT CURRENT
NO LOAD
Tc = –55°C TO +125°C
—
—
5.5
6.0
10
11
—
—
6.0
6.5
10
12
—
—
6.0
6.5
11
12
FULL LOAD
Tc = –55°C TO +125°C
—
—
70
73
74
78
—
—
68
70
72
74
—
—
68
70
72
74
mA
INHIBITED
Tc = –55°C TO +125°C
—
—
2.3
2.4
3.2
3.5
—
—
2.3
2.4
3.2
3.5
—
—
2.3
2.4
3.2
3.5
INPUT RIPPLE
CURRENT
10k Hz - 10 MHz
Tc = –55°C TO +125°C
—
—
100
130
200
250
—
—
100
150
200
250
—
—
100
150
200
250
mA p-p
%
2
EFFICIENCY
Tc = 25°C
Tc = –55°C TO +125°C
72
69
77
75
—
—
74
72
79
77
—
—
74
72
79
77
—
—
3, 4
LOAD FAULT
POWER DISSIPATION
Tc = –55°C TO +125°C
—
—
1.3
1.4
2.0
2.3
—
—
2.0
2.2
3.2
3.5
—
—
2.3
2.5
3.7
4.0
W
RECOVERY
Tc = -–55°C TO +125°C
—
—
3.0
3.5
12
15
—
—
3.5
3.5
15
20
—
—
4.0
4.0
18
20
ms
mV pk
µs
STEP LOAD
TRANSIENT
Tc = –55°C TO +125°C
–400
–500
185
185
400
500
–700
–800
350
380
700
800
–700
–800
350
380
700
800
5
RESPONSE
50 %–100%– 50%
RECOVERY
Tc = –55°C TO +125°C
—
—
125
125
500
600
—
—
130
130
500
600
—
—
140
180
600
750
STEP LINE
RESPONSE
TRANSIENT
Tc = –55°C TO +125°C
–400
–500
170
180
400
500
–900
–1000
400
400
900
1000
–750
–850
400
450
750
850
mV pk
ms
5
12 TO 50 TO 12 V
IN
RECOVERY
Tc = –55°C TO +125°C
—
—
0.75
0.75
3.0
4.0
—
—
0.6
0.6
2.5
3.0
—
—
0.47
0.5
2.0
2.5
START-UP
0 TO 28 VDC
DELAY
Tc = –55°C TO +125°C
OVERSHOOT
—
—
—
—
7
10
0
20
40
100
150
—
—
—
—
7
10
0
20
40
250
350
—
—
—
—
7
10
0
20
40
300
450
ms
mV pk
Tc = –55°C TO +1 25°C
0
0
0
Notes
1. Specified at 50% of full load.
2. Lin = 2 µH
3. Max. duration of short circuit: 25°C– 90 seconds; 125°C – 30 seconds.
4. Load fault is a short circuit (<50 mohms). Recovery into resistive full load.
5. Input step transition ≥ 10 µs.Recovery is time to settle to within 1% of Vout
final value.
B2-94
MGH SERIES
1.5 WATT
DC/DC CONVERTERS
Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
DUAL OUTPUT MODELS
PARAMETER
OUTPUT VOLTAGE
MGH2805D
MGH2812D
MGH2815D
CONDITIONS
Tc = 25°C
MIN
±4.95
±4.80
TYP
±5
±5
MAX
±5.05
±5.20
MIN
±11.88
±11.52
TYP
±12
±12
MAX
±12.12
±12.48
MIN
TYP
±15
±15
MAX
±15.15
±15.60
UNITS
1
±14.85
±14.40
VDC
Tc = –55°C TO +125°C
2
OUTPUT CURRENT
V
= 12 to 50 VDC
= 12 to 50 VDC
0
±150
240
0
±62.5
100
0
±50
80
mA
W
IN
OUTPUT POWER
OUTPUT RIPPLE
V
0
—
35
50
1.5
150
250
0
—
35
40
1.5
150
250
0
—
30
35
1.5
150
250
IN
10 kHz - 2 MHz
—
—
—
—
—
—
VOLTAGE +V
OUT
Tc = –55°C TO +125°C
mV p-p
V
–V
10 kHz - 2 MHz
—
—
35
50
150
250
—
—
35
40
150
250
—
—
30
35
150
250
OUT
Tc = –55°C TO +125°C
3
LINE REGULATION
VIN = 12 to 50 VDC
Tc = –55°C TO +125°C
—
—
10
20
50
100
—
—
100
110
300
400
—
—
165
180
500
650
LOAD
3
REGULATION , 4
10% TO FULL LOAD
–55°C TO +125°C
—
—
300
350
600
700
—
—
550
570
1100
1200
—
—
600
630
1300
1400
mV
mV
50% TO FULL LOAD
–55°C TO +125°C
—
—
80
100
200
300
—
—
115
130
250
350
—
—
125
135
300
400
CROSS
5
REGULATION
–V
—
—
400
—
—
500
—
—
500
OUT
INPUT VOLTAGE
NO LOAD TO FULL
CONTINUOUS
TRANSIENT 120 ms
12
0
28
—
50
80
12
0
28
—
50
80
12
0
28
—
50
70
VDC
V
INPUT CURRENT
NO LOAD
Tc = –55°C TO +125°C
—
—
5.0
6.0
10
12
—
—
7.5
8.0
13
14
—
—
7.5
8.0
13
14
FULL LOAD
Tc = –55°C TO +125°C
—
—
69
72
73
77
—
—
70
71
73
77
—
—
71
72
74
78
mA
INHIBITED
Tc = –55°C TO +125°C
—
—
2.3
2.4
3.2
3.5
—
—
2.3
2.4
3.2
3.5
—
—
2.3
2.4
3.2
3.5
6
INPUT RIPPLE
CURRENT
10 kHz - 10 MHz
Tc = –55°C TO +125°C
—
—
100
130
200
250
—
—
115
150
200
250
—
—
90
120
200
250
mA p-p
%
EFFICIENCY
Tc = 25°C
Tc = –55°C TO +125°C
73
70
77
75
—
—
73
70
77
75
—
—
72
69
76
74
—
—
7,8
LOAD FAULT
POWER DISSIPATION
Tc = –55°C TO +125°C
—
—
1.4
1.6
2.2
2.5
—
—
2.5
2.7
3.8
4.2
—
—
2.7
3.0
4.1
4.5
W
RECOVERY
Tc = –55°C TO +125°C
—
—
3.7
3.8
15
20
—
—
3.2
3.2
15
20
—
—
4.0
4.0
15
20
ms
STEP LOAD
RESPONSE
TRANSIENT
Tc = –55°C TO +125°C
–300
–400
130
140
300
400
–600
–700
250
260
600
700
–600
–700
250
270
600
700
mV pk
µs
9
± V
out
50 %–100%– 50%
RECOVERY
–55°C TO +125°C
—
—
100
100
400
500
—
—
165
165
700
800
—
—
50
50
200
300
STEP LINE
RESPONSE
TRANSIENT
Tc = –55°C TO +125°C
–250
–300
125
130
250
300
–500
–600
240
250
500
600
–500
–600
220
230
500
600
mV pk
ms
19
± V
out
12 TO 50 TO 12 V
RECOVERY
Tc = –55°C TO +125°C
—
—
0.6
0.6
2.5
3.0
—
—
0.9
0.9
3.0
4.0
—
—
0.6
0.7
3.0
4.0
IN
START–UP
0 TO 28 VDC, ± V
DELAY
Tc = –55°C TO +125°C
—
—
8
10
25
45
—
—
8
10
25
45
—
—
8
10
25
45
ms
out
OVERSHOOT
Tc = –55°C TO +125°C
—
—
0
0
100
150
—
—
0
0
250
350
—
—
0
0
750
900
mV pk
Notes:
1. Specified at 50% load.
6. Lin = 2 µH.
2. Max. spec indicates 80% of the converter’s total available power. This 80%
is available from either output.
3. Specification applies to both + and –Vout.
4. Although no minimum load is required, at no load the output voltage may
increase up to 15%.
7. Max. duration of short circuit: 25°C – 90 seconds; 125°C – 30 seconds.
8. Load fault is a short circuit (<50 mohms). Recovery into resistive full load.
9. Input step transition ≥ 10 µs.Recovery is time to settle to within 1% of Vout
final value.
5. Cross regulation is specified as the effect on –Vout for the following percent-
ages of total output power: +Po = 20% and
–Po = 80% to +Po=80% and –Po=20%
B2-95
MGH SERIES
1.5 WATT
DC/DC CONVERTERS
Positive
Input
+
+V
FB
+V
Positive
Output
in
+
+
PWM
Controller
Shutdown
Inhibit
Input
out
Output
Common
Negative
Output
Common
Dual models only
Case
Ground
FIGURE 1: BLOCK DIAGRAM
SMD NUMBERS
PIN OUT
Single Output
STANDARD MICROCIRCUIT
MGH SERIES
SIMILAR PART
Pin
1
Dual Output
Positive Input
No connection
Input Common
Positive Output
Case Ground
DRAWING (SMD)
Positive Input
No connection
Input Common
Positive Output
Case Ground
2
5962-9569601HXC
5962-9569701HXC
5962-9569801HXC
5962-9570201HXC
5962-9570301HXC
5962-9570401HXC
MGH2805S/883
MGH2812S/883
MGH2815S/883
MGH2805D/883
MGH2812D/883
MGH2815D/883
3
4, 5
6, 7
8, 9
10, 11
12
Output Common Output Common
For exact specifications for an SMD product, refer to the SMD
drawing. Call your Interpoint representative for status on the
MGH SMD releases. See Section A3, SMDs, for more infor-
mation.
Case Ground
No connection
No connection
Case Ground
No connection
Negative Output
No connection
Inhibit
13, 14
15, 16, 17 No connection
18 Inhibit
To meet specified performance, all pins must
be connected except “No Connection” pins.
MODEL NUMBERING KEY
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
MGH
28 12
S
Z / ES
Base Model
Input Voltage
Output Voltage
TOP VIEW
MGH
Number of Outputs
(S = single, D = dual)
Gull Wing Lead Option
(Straight leaded case has no designator
in this position.)
Differently colored glass bead around pin one or dimple in
header (bottom or side of case) indicates pin one.
Cover marking is oriented with pin one at the upper right corner.
Screening
(Standard screening has no designator
in this position.)
See Section B8, case B, for dimensions and “gull-wing” option.
FIGURE 2: PIN OUT
B2-96
MGH SERIES
1.5 WATT
DC/DC CONVERTERS
Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, unless otherwise specified.
90
80
70
90
80
70
90
80
70
60
50
40
30
12 VOLT
12 VOLT
28 VOLT
12 VOLT
28 VOLT
28 VOLT
50 VOLT
60
50
60
50
50 VOLT
50 VOLT
40
30
40
30
0
0.25 0.5
1
1.25 1.5 1.75
0.75
0
0.25 0.5
1
1.25 1.5 1.75
12 & 15 V SINGLES
0.75
0
0.25 0.5
1
1.25 1.5 1.75
ALL 5 VOLT MODELS
0.75
OUTPUT POWER
12 & 15 V DUAL MODELS
OUTPUT POWER
OUTPUT POWER
EFFICIENCY vs LINE & LOAD
EFFICIENCY vs LINE & LOAD
EFFICIENCY vs LINE & LOAD
FIGURE 3
FIGURE 4
FIGURE 5
0
20
V
in
50 VDC
12 VDC
FULL LOAD TO HALF LOAD
40
60
V
out
80
HALF LOAD TO FULL LOAD
100
1
10
60
500 s / div.
MGH2805S
200 s / div.
MGH2805S
FREQUENCY (kHz)
MGH2815S - Representative of all models
AUDIO REJECTION
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
FIGURE 6
FIGURE 7
FIGURE 8
V
in
V
+V
OUT
–V
OUT
FULL LOAD TO HALF LOAD
HALF LOAD TO FULL LOAD
in
50 VDC
12 VDC
+V
–V
out
V
out
–V
+V
FULL LOAD TO HALF LOAD
HALF LOAD TO FULL LOAD
OUT
OUT
out
0
2
4
6
8
10 12 14 16 18
MGH2805S
TIME (ms)
500 s / div.
MGH2815D
200 s / div.
MGH2815D
Representative of all 5 volt models
TURN-ON INTO FULL LOAD
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
FIGURE 9
FIGURE 10
FIGURE 11
B2-97
MGH SERIES
1.5 WATT
DC/DC CONVERTERS
Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, unless otherwise specified.
4
2
4
2
0
–5
±5
V
in
±12
±15
–15
–12
0
+15
+12
+5
0 V for –V
out
–V
5
+V
out
out
-2
-4
-2
-4
0 V for +V
out
0
10 15 20 25 30 35 40 45
MGH2815D
TIME (ms)
90/10 70/30 50/50 30/70 10/90
OUTPUT LOAD (%) DUAL
90% TO 10% LOAD ON +V
10
20
40
50
DUAL
30
Also representative of MGH2812S & D and MGH2815S
TURN-ON INTO FULL LOAD
OUTPUT LOAD (%)
50% LOAD +V; 50% TO 10% LOAD –V
AND
10% TO 90% LOAD ON –V
50% LOAD –V; 50% TO 10% LOAD +V
CROSS REGULATION
CROSS REGULATION
FIGURE 12
FIGURE 13
FIGURE 14
120
100
80
TRIP POINT
125%
60
SAFE OPERATING AREA
40
20
0
20
40 60 80 100 120 140 160
% OF FULL LOAD
0
OUTPUT VOLTAGE vs. OUTPUT LOAD
FIGURE 15
22622-001-DTS Rev A
DQ# 1033
All technical information is believed to be accurate, but no responsibility is
assumed for errors or omissions. Interpoint reserves the right to make changes in
products or specifications without notice. MGH Series is a trademark of Interpoint.
Copyright © 1998 - 1999 Interpoint. All rights reserved.
B2-98
CASE B
CASES
TOP VIEW CASE B
FMGA EMI Filter: Screening – Standard, ES, or 883
MGH Series: Screening – Standard, ES, or 883
Differently colored glass bead around pin one or dimple
in header (bottom or side of case) indicates pin one.
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
0.900 (22.86)
0.800 (20.32)
0.700 (17.78)
0.600 (15.24)
0.500 (12.70)
0.400 (10.16)
0.300 ( 7.62)
0.200 ( 5.08)
0.100 ( 2.54)
CASE B
TOP VIEW
See Figure 6
for pin
configurations.
1.010 max
(25.65)
(This view shows
straight leads.)
0.015
(0.38)
0.000
Differently colored glass bead around pin one or dimple in
header (bottom or side of case) indicates pin one.
0.880 max
(22.35)
Cover marking is oriented with pin one at the upper right corn
Cover marking is oriented with pin one
at the upper right corner.
Materials
0.010
(0.25)
1.870 ref. (47.50)
0.08 (2.0)
Header
Cover
Pins
Kovar/Nickel/Gold
Kovar/Nickel
Kovar/Nickel/Gold,
matched glass seal
0.250 max.
Straight Leads
(6.35)
0.50
(12.7)
Seam seal
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
1.140 ref. (28.96)
0.135 ref. (3.43)
0.010
1
(0.25)
CAUTION
Gull Wing Leads
Option
Maximum reflow temperature is 220°C for a
maximum of 30 seconds. SN60, SN62, or SN63
are the recommended types of solder. See below
for Solder Mask instructions.
1
Gull wing leads are solder dipped.
Lead dimensions are prior to solder dip.
0.010 (0.25)
Bottom of case to
bottom of lead
0.055
(1.40)
Hand soldering should not exceed 300°C for 10
seconds per pin.
FIGURE 5: CASE B MAXIMUM DIMENSIONS
0.08
(2.0)
0.070
(1.78)
FIGURE 6: CASE B
Solder Mask Notes
0.075 (1.91)
1. Pad dimensions are for the solder mask opening. Lead common to
each other can be connected underneath as desired.
2. Ground pins should be connected to the center pad for improved
grounding.
0.060 (1.52)
0.870 (22.10)
0.030 (0.76)
3. Center pad should not have a solder mask. Solder, copper, or Au/Ni
plate are preferred over solder for adhesive attach.
4. Solder coat to solder down converter.
5. If less rotation of case is desired, make the pad width 0.020inches
(0.51 mm). Pad length can be extended 0.010 inches (0.25 mm)
towards the case body and as-desired dimension away from the case
body.
6. Do not exceed 220°C as measured on the body of the converter (top
or bottom).
7. Attach the body of the case to the board with a thermally conductive
adhesive or SN60, 62, or 63 solder. The adhesive can be electrically
conductive as well. It can be applied as an underfill post solder or
dispensed and cured prior or during solder.
1.000
(25.40)
0.100 (2.54) 16X
0.100 (2.54) 4X
FIGURE 7: CASE B SOLDER MASK
Note: Although every effort has been made to render the case drawings at actual size, variations in the printing process may cause some distortion. Please refer
to the numerical dimensions for accuracy.
B8-7
QA SCREENING
125°C PRODUCTS
125°C PRODUCTS
TEST (125°C Products)
STANDARD
/ES
/883 (Class H)*
PRE-CAP INSPECTION
Method 2017, 2032
yes
yes
yes
TEMPERATURE CYCLE (10 times)
Method 1010, Cond. C, -65°C to 150°C
Method 1010, Cond. B, -55°C to 125°C
no
no
no
yes
yes
no
CONSTANT ACCELERATION
Method 2001, 3000 g
Method 2001, 500 g
no
no
no
yes
yes
no
BURN-IN
Method 1015, 160 hours at 125°C
96 hours at 125°C case (typical)
no
no
no
yes
yes
no
FINAL ELECTRICAL TEST MIL-PRF-38534, Group A
Subgroups 1 through 6: -55°C, +25°C, +125°C
Subgroups 1 and 4: +25°C case
no
yes
no
yes
yes
no
HERMETICITY TESTING
Fine Leak, Method 1014, Cond. A
Gross Leak, Method 1014, Cond. C
Gross Leak, Dip (1 x 10 )
no
no
yes
yes
yes
no
yes
yes
no
-3
FINAL VISUAL INSPECTION
Method 2009
yes
yes
yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534.
*883 products are built with element evaluated components and are 100% tested and guaranteed over
the full military temperature range of –55°C to +125°C.
Applies to the following products
MOR Series
MFLHP Series
MFL Series
MHP Series
MTR Series
MQO Series**
MHD Series
MHV Series
MHF+ Series
MHF Series**
MGA Series
MSA Series
MGH Series
MCH Series
FM-704A EMI Filter
FMD**/FME EMI Filter
FMC EMI Filter
FMH EMI Filter
FMGA EMI Filter
FMSA EMI Filter
HUM Modules**
LCM Modules**
LIM Modules
**MFLHP Series, MQO Series, MHF Series, FMD EMI Filters, Hum Modules, and LCM Modules do not offer
‘883” screening.
C2-10
MGH2812DZ/883 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
MGH2812DZ/ES | CRANE | DC/DC CONVERTERS 28 VOLT INPUT | 获取价格 | |
MGH2812S | CRANE | MCH/MGH Single and Dual DC/DC Converters | 获取价格 | |
MGH2812S/883 | CRANE | MCH/MGH Single and Dual DC/DC Converters | 获取价格 | |
MGH2812SG/883 | CRANE | Analog Circuit, | 获取价格 | |
MGH2812SY/883 | CRANE | 1-OUTPUT 1.5W DC-DC REG PWR SUPPLY MODULE | 获取价格 | |
MGH2812SZ | CRANE | Analog Circuit, | 获取价格 | |
MGH2812SZ/883 | CRANE | MCH/MGH Single and Dual DC-DC Converters 28 Volt input â 1.5 Watt | 获取价格 | |
MGH2812SZ/ES | CRANE | DC/DC CONVERTERS 28 VOLT INPUT | 获取价格 | |
MGH2815D | CRANE | MCH/MGH Single and Dual DC/DC Converters | 获取价格 | |
MGH2815D/883 | CRANE | MCH/MGH Single and Dual DC/DC Converters | 获取价格 |
MGH2812DZ/883 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6