HA2-2602/883 [INTERSIL]
Wideband, High Impedance Operational Amplifier; 宽带，高阻抗运算放大器
| 型号： | HA2-2602/883 |
| 厂家： | 
Intersil |
| 描述： | Wideband, High Impedance Operational Amplifier |
| 文件： | 总5页 (文件大小：148K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
HA-2602/883
Wideband, High Impedance
Operational Amplifier
October 2004
Features
Des cription
• This Circuit is Processed in Accordance to MIL-STD- The HA-2602/883 is an internally compensated bipolar oper-
883 and is Fully Conformant Under the Provisions of ational amplifier that features very high input impedance
Paragraph 1.2.1.
coupled with wideband AC performance. The high resis-
tance of the input stage is complemented by low offset volt-
age (5mV max at +25oC) and low bias and offset current
(25nA max at +25oC) to facilitate accurate signal processing.
Offset voltage can be reduced further by means of an exter-
nal nulling potentiometer. The 4V/µs minimum slew rate at
+25oC and the minimum open loop gain of 80kV/V at +25oC
enables the HA-2602/883 to perform high gain amplification
of fast, wideband signals. These dynamic characteristics,
coupled with fast settling times, make these amplifiers ide-
ally suited to pulse amplification designs as well as high fre-
quency or video applications. The frequency response of the
amplifier can be tailored to exact design requirements by
means of an external bandwidth control capacitor. Other
high performance designs such as high gain, low distortion
audio amplifiers, high-Q and wideband active filters and high
speed comparators, are excellent uses of this part.
• High Input Impedance . . . . . . . . . . . . . . . . . 40MΩ (Min)
500MΩ (Typ)
• High Slew Rate. . . . . . . . . . . . . . . . . . . . . . . .4V/µs (Min)
7V/µs (Typ)
• Low Input Bias Current . . . . . . . . . . . . . . . . 25nA (Max)
1nA (Typ)
• Low Input Offset Current. . . . . . . . . . . . . . . . 5mV (Max)
• Wide Unity Gain Bandwidth . . . . . . . . . . . 12MHz (Typ)
• Output Short Circuit Protection
Applications
• Video Amplifier
• Pulse Amplifier
Part Number Information
• High-Q Active Filters
• High Speed Comparators
• Low Distortion Oscillators
PART
NUMBER
TEMPERATURE
RANGE
PACKAGE
8 Pin Can
HA2-2602/883
-55oC to +125oC
Pinout
HA-2602/883
(METAL CAN)
TOP VIEW
COMP
8
BAL
V+
1
3
7
-
+
2
6
OUT
-IN
5
+IN
BAL
4
V-
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Spec Number 511005-883
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002, 2004. All Rights Reserved
1
FN3700.2
HA-2602/883
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Thermal Resistance
θJA
θJC
Metal Can Package . . . . . . . . . . . . . . . . . 160oC/W 75oC/W
Voltage at Either Input Terminal. . . . . . . . . . . . . . . . . . . . . . V+ to V- Package Power Dissipation Limit at +75oC for TJ ≤ +175oC
Peak Output Current . . . . . . . . . . . . . . .Full Short Circuit Protection
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mW
Package Power Dissipation Derating Factor Above +75oC
Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mW/oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
Operating Conditions
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
V
INCM ≤ 1/2 (V+ - V-)
Operating Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V
RL ≥ 2kΩ
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
HA-2602/883
GROUP A
PARAMETERS
SYMBOL
CONDITIONS
SUBGROUPS TEMPERATURE
MIN
-5
MAX UNITS
Input Offset
Voltage
VIO
VCM = 0V
1
2, 3
1
+25oC
+125oC, -55oC
+25oC
5
7
mV
mV
nA
nA
nA
nA
nA
nA
V
-7
Input Bias Current
+IB
-IB
VCM = 0V, +RS = 100kΩ, -RS = 100Ω
VCM = 0V, +RS = 100Ω, -RS = 100kΩ
VCM = 0V, +RS = 100kΩ, -RS = 100kΩ
V+ = +4V, V- = -26V
-25
-60
-25
-60
-25
-60
11
11
-
25
60
25
60
25
60
-
2, 3
1
+125oC, -55oC
+25oC
2, 3
1
+125oC, -55oC
+25oC
Input Offset
Current
IIO
2, 3
1
+125oC, -55oC
+25oC
Common Mode
Range
+CMR
-CMR
+AVOL
-AVOL
+CMRR
-CMRR
+VOUT
-VOUT
2, 3
1
+125oC, -55oC
+25oC
-
V
V+ = +26V, V- = -4V
-11
-11
-
V
2, 3
4
+125oC, -55oC
+25oC
-
V
Large Signal
Voltage Gain
VOUT = 0V and +10V, RL = 2kΩ
VOUT = 0V and -10V, RL = 2kΩ
∆VCM = +10V, V+ = +5V, V- = -25V,
80
60
80
60
74
74
74
74
10
10
-
kV/V
kV/V
kV/V
kV/V
dB
dB
dB
dB
V
5, 6
4
+125oC, -55oC
+25oC
-
-
5, 6
1
+125oC, -55oC
+25oC
-
Common Mode
Rejection Ratio
-
V
OUT = -10V
2, 3
1
+125oC, -55oC
+25oC
-
∆VCM = -10V, V+ = +25V, V- = -5V,
OUT = +10V
-
V
2, 3
4
+125oC, -55oC
+25oC
-
Output Voltage
Swing
RL = 2kΩ
RL = 2kΩ
-
5, 6
4
+125oC, -55oC
+25oC
-
V
-10
-10
V
5, 6
+125oC, -55oC
-
V
Spec Number 511005-883
2
HA-2602/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
HA-2602/883
GROUP A
PARAMETERS
SYMBOL
CONDITIONS
VOUT = -10V
SUBGROUPS TEMPERATURE
MIN
10
MAX UNITS
Output Current
+IOUT
4
5, 6
4
+25oC
+125oC, -55oC
+25oC
-
mA
mA
mA
mA
mA
mA
mA
mA
dB
7.5
-
-
-IOUT
VOUT = +10V
-10
5, 6
1
+125oC, -55oC
+25oC
-
-7.5
Quiescent Power
Supply Current
+ICC
VOUT = 0V, IOUT = 0mA
VOUT = 0V, IOUT = 0mA
-
3.7
2, 3
1
+125oC, -55oC
+25oC
-
4.0
-ICC
-3.7
-4.0
74
-
-
-
-
-
-
-
-
-
-
2, 3
1
+125oC, -55oC
+25oC
Power Supply
Rejection Ratio
+PSRR
-PSRR
+VIOAdj
-VIOAdj
∆VSUP = ±5V, V+ = +10V, V- = -15V,
V+ = +20V, V- = -15V
2, 3
1
+125oC, -55oC
+25oC
74
dB
∆VSUP = ±5V, V+ = +15V, V- = -10V,
V+ = +15V, V- = -20V
74
dB
2, 3
1
+125oC, -55oC
+25oC
74
dB
Offset Voltage
Adjustment
Note 1
Note 1
VIO-1
VIO-1
VIO+1
VIO+1
mV
mV
mV
mV
2, 3
1
+125oC, -55oC
+25oC
2, 3
+125oC, -55oC
NOTE:
1. Offset adjustment range is [VIO(Measured) ±1mV] minimum referred to output. This test is for functionality only to assure adjustment
through 0V.
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified.
HA-2602/883
GROUP A
PARAMETERS
SYMBOL
CONDITIONS
VOUT = -5V to +5V
SUBGROUPS TEMPERATURE
MIN
MAX UNITS
Slew Rate
+SR
7
8A, 8B
7
+25oC
+125oC, -55oC
+25oC
4
3
4
3
-
-
-
V/µs
V/µs
V/µs
V/µs
ns
-SR
TR
VOUT = +5V to -5V
-
8A, 8B
7
+125oC, -55oC
+25oC
-
Rise and Fall
Time
VOUT = 0 to +200mV, 10% ≤ TR ≤ 90%
VOUT = 0 to -200mV, 10% ≤ TF ≤ 90%
60
70
60
70
8A, 8B
7
+125oC, -55oC
+25oC
-
ns
TF
-
ns
8A, 8B
+125oC, -55oC
-
ns
Spec Number 511005-883
3
HA-2602/883
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified.
HA-2602/883
GROUP A
PARAMETERS
SYMBOL
CONDITIONS
VOUT = 0 to +200mV
SUBGROUPS TEMPERATURE
MIN
MAX UNITS
Overshoot
+OS
7
+25oC
+125oC, -55oC
+25oC
-
-
-
-
40
50
40
50
%
%
%
%
8A, 8B
7
-OS
VOUT = 0 to -200mV
8A, 8B
+125oC, -55oC
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, Unless Otherwise Specified.
HA-2602/883
PARAMETERS
SYMBOL
CONDITIONS
NOTES
TEMPERATURE
MIN
MAX UNITS
Differential Input
Resistance
RIN
VCM = 0V
1
+25oC
40
-
-
-
MΩ
kHz
V/V
Full Power
Bandwidth
FPBW
CLSG
+ISC
V
PEAK = 10V
1, 2
1
+25oC
50
1
Minimum Closed
Loop Stable Gain
RL = 2kΩ, CL = 50pF
VOUT = 1V, RL = 10Ω
-55oC to +125oC
Output Short
Circuit Current
1
1
+25oC
+125oC
-
-
50
45
60
-
mA
mA
mA
mA
mA
mA
mW
1
-55oC
-
-ISC
VOUT = -1V, RL = 10Ω
1
+25oC
-50
-45
-60
-
1
+125oC
-
1
-55oC
-
Quiescent Power
Consumption
PC
V
OUT = 0V, IOUT = 0mA
1, 3
-55oC to +125oC
120
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These param-
eters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.)
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
Interim Electrical Parameters (Pre Burn-In)
Final Electrical Test Parameters
Group A Test Requirements
SUBGROUPS (SEE TABLES 1 AND 2)
1
1 (Note 1), 2, 3, 4, 5, 6, 7, 8A, 8B
1, 2, 3, 4, 5, 6, 7, 8A, 8B
1
Groups C and D Endpoints
NOTE:
1. PDA applies to Subgroup 1 only.
Spec Number 511005-883
4
HA-2602/883
Die Characteristics
DIE DIMENSIONS:
69 x 56 x 19 mils ± 1 mils
1750 x 1420 x 483µm ± 25.4µm
Silox Thickness: 12kÅ ± 2kÅ
Nitride Thickness: 3.5kÅ ± 1.5kÅ
WORST CASE CURRENT DENSITY:
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16kÅ ± 2kÅ
3.9 x 104A/cm2
SUBSTRATE POTENTIAL (Powered Up): Unbiased
TRANSISTOR COUNT:
HA-2602/883: 140
GLASSIVATION:
Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.)
Metallization Mas k Layout
HA-2602/883
+IN
-IN
BAL
V-
COMP
V+
BAL
OUT
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
Spec Number 511005-883
5
相关型号：
HA2-2620-2
100MHz, High Input Impedance, Very Wideband, Uncompensated Operational Amplifiers
INTERSIL
HA2-2625-5
100MHz, High Input Impedance, Very Wideband, Uncompensated Operational Amplifiers
INTERSIL
©2020 ICPDF网 联系我们和版权申明