ISL9014IRCCZ [INTERSIL]
Dual LDO with Low Noise, Low IQ, and High PSRR; 双路LDO具有低噪声,低智商,和高PSRR型号: | ISL9014IRCCZ |
厂家: | Intersil |
描述: | Dual LDO with Low Noise, Low IQ, and High PSRR |
文件: | 总11页 (文件大小:212K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ISL9014
®
Data Sheet
April 26, 2006
FN9245.2
Dual LDO with Low Noise, Low I , and
Q
Features
High PSRR
• Integrates two high performance LDOs
- VO1 - 300mA output
ISL9014 is a high performance dual LDO capable of
sourcing 300mA current from both outputs. The device has a
low standby current and high-PSRR and is stable with output
capacitance of 1μF to 10μF with ESR of up to 200mΩ.
- VO2 - 300mA output
• Excellent transient response to large current steps
• Excellent load regulation: <1% voltage change across full
range of load current
A reference bypass pin allows an external capacitor for
adjusting a noise filter for low noise and high PSRR
applications.
• High PSRR: 70dB @ 1kHz
• Wide input voltage capability: 2.3V - 6.5V
• Extremely low quiescent current: 45μA (both LDOs active)
• Low dropout voltage: typically 200mV @ 300mA
• Low output noise: typically 30μVrms @ 100μA (1.5V)
• Stable with 1-10μF ceramic capacitors
The quiescent current is typically only 45μA with both LDOs
enabled and active. Separate enable pins control each
individual LDO output. When both enable pins are low, the
device is in shutdown, typically drawing less than 0.1μA.
Several combinations of voltage outputs are standard.
Others are available on request. Output voltage options for
each LDO range from 1.2V to 3.6V.
• Separate enable pins for each LDO
• Soft-start to limit input current surge during enable
• Current limit and overheat protection
Pinout
ISL9014
10 LD 3X3 DFN
TOP VIEW
• ±1.8% accuracy over all operating conditions
• Tiny 10 Ld 3x3mm DFN package
1
2
3
4
5
10 VO1
VIN
EN1
• -40°C to +85°C operating temperature range
• Pin compatible with Micrel MIC2211
9
8
7
6
VO2
NC
EN2
• Pb-free plus anneal available (RoHS compliant)
NC
CBYP
NC
Applications
GND
• PDAs, Cell Phones and Smart Phones
• Portable Instruments, MP3 Players
• Handheld Devices including Medical Handhelds
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2005, 2006. All Rights Reserved.
1
All other trademarks mentioned are the property of their respective owners.
ISL9014
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
PACKAGE
(Pb-Free)
PART MARKING VO1 VOLTAGE VO2 VOLTAGE TEMP RANGE (°C)
PKG. DWG. #
ISL9014IRNNZ
DCBS
DBBK
DBBL
DCBT
DCBV
DBBV
DCCC
DCEA
DCCG
DBBW
DCFA
DBBM
DDJA
DCBA
DCCH
DBBT
DCDA
DBBP
DCCA
DDBA
DBBR
DBBN
DCCV
DCDB
DBBY
DDCA
DCDH
DCDL
DCDS
DBBS
DCDV
DDFA
3.3V
3.3V
3.3V
3.3V
3.0V
3.0V
3.0V
2.9V
2.85V
2.85V
2.85V
2.85V
2.85V
2.85V
2.8V
2.8V
2.8V
2.8V
2.8V
2.7V
2.7V
2.5V
2.5V
2.5V
1.85V
1.85V
1.8V
1.8V
1.5V
1.5V
1.5V
1.5V
3.3V
2.8V
2.5V
1.8V
3.3V
3.0V
2.7V
2.9V
3.3V
2.85V
2.8V
2.5V
1.85V
1.8V
3.3V
3.0V
2.6V
1.8V
1.5V
1.85V
1.8V
2.8V
2.0V
1.8V
2.9V
1.85V
2.8V
1.8V
2.9V
2.8V
1.8V
1.5V
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
10 Ld 3x3 DFN L10.3x3C
ISL9014IRNJZ
ISL9014IRNFZ
ISL9014IRNCZ
ISL9014IRMNZ
ISL9014IRMMZ
ISL9014IRMGZ
ISL9014IRLLZ
ISL9014IRKNZ
ISL9014IRKKZ
ISL9014IRKJZ
ISL9014IRKFZ
ISL9014IRKPZ
ISL9014IRKCZ
ISL9014IRJNZ
ISL9014IRJMZ
ISL9014IRJRZ
ISL9014IRJCZ
ISL9014IRJBZ
ISL9014IRGPZ
ISL9014IRGCZ
ISL9014IRFJZ
ISL9014IRFDZ
ISL9014IRFCZ
ISL9014IRPLZ
ISL9014IRPPZ
ISL9014IRCJZ
ISL9014IRCCZ
ISL9014IRBLZ
ISL9014IRBJZ
ISL9014IRBCZ
ISL9014IRBBZ
NOTES:
1. Add “-T” to part number for tape and reel.
2. For availability and lead time of devices with voltage combinations not listed in the table, contact Intersil Marketing.
3. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are
MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN9245.2
April 26, 2006
2
ISL9014
Absolute Maximum Ratings
Thermal Information
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1V
Thermal Resistance (Notes 4, 5)
θ
(°C/W)
50
θ
(°C/W)
10
JA
JC
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (V +0.3)V
IN
3x3 DFN Package . . . . . . . . . . . . . . . .
Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C
Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C
Recommended Operating Conditions
Ambient Temperature Range (T ) . . . . . . . . . . . . . . . .-40°C to 85°C
A
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
4. θ is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
JA
Tech Brief TB379.
5. θ , “case temperature” location is at the center of the exposed metal pad on the package underside. See Tech Brief TB379.
JC
Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature
range of the device as follows:
T
= -40°C to +85°C; V = (V +1.0V) to 6.5V with a minimum V of 2.3V; C = 1μF; C = 1μF;
A
IN
O
IN
IN
O
C
= 0.01μF
BYP
PARAMETER
DC CHARACTERISTICS
Supply Voltage
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
V
2.3
6.5
V
IN
Ground Current
Quiescent condition: I = 0μA; I = 0μA
O1 O2
I
One LDO active
Both LDO active
@25°C
25
45
40
60
μA
μA
μA
V
DD1
DD2
DDS
I
Shutdown Current
UVLO Threshold
I
0.1
2.1
1.8
1.0
2.3
2.0
+1.8
V
1.9
1.6
UV+
V
V
UV-
Regulation Voltage Accuracy
Variation from nominal voltage output, V = V +0.5 to 5.5V,
IN
-1.8
%
O
T = -40°C to 125°C
J
Line Regulation
Load Regulation
V
= (V
+1.0V relative to highest output voltage) to 5.5V
OUT
-0.2
0
0.2
0.7
1.0
%/V
%
IN
I
I
= 100μA to 150mA
= 100μA to 300mA
0.1
OUT
OUT
%
Maximum Output Current
I
VO1: Continuous
VO2: Continuous
300
300
350
mA
mA
mA
mV
mV
mV
mV
°C
MAX
Internal Current Limit
I
V
V
V
V
T
475
125
300
250
200
145
110
600
200
500
400
325
LIM
Dropout Voltage (Note 6)
I
I
I
I
= 150mA; V > 2.1V
O
DO1
DO2
DO3
DO4
SD+
O
O
O
O
= 300mA; V < 2.5V
O
= 300mA; 2.5V ≤ V ≤ 2.8V
O
= 300mA; V > 2.8V
O
Thermal Shutdown Temperature
T
°C
SD-
AC CHARACTERISTICS
Ripple Rejection
I
= 10mA, V = 2.8V(min), V = 1.8V, C
IN
= 0.1μF
BYP
O
O
@ 1kHz
70
55
40
30
dB
dB
@ 10kHz
@ 100kHz
dB
Output Noise Voltage
I
= 100μA, V = 1.5V, T = 25°C, C
BYP
= 0.1μF
μVrms
O
O
A
BW = 10Hz to 100kHz
FN9245.2
April 26, 2006
3
ISL9014
Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature
range of the device as follows:
T
= -40°C to +85°C; V = (V +1.0V) to 6.5V with a minimum V of 2.3V; C = 1μF; C = 1μF;
A
IN
O
IN
IN
O
C
= 0.01μF (Continued)
BYP
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
DEVICE START-UP CHARACTERISTICS
Device Enable TIme
T
Time from assertion of the ENx pin to when the output voltage
reaches 95% of the VO(nom)
250
30
500
60
μs
EN
LDO Soft-Start Ramp Rate
T
Slope of linear portion of LDO output voltage ramp during
start-up
μs/V
SSR
EN1, EN2 PIN CHARACTERISTICS
Input Low Voltage
V
-0.3
1.4
0.5
V
V
IL
Input High Voltage
Input Leakage Current
Pin Capacitance
V
V
+0.3
IN
IH
I , I
IL IH
0.1
μA
pF
C
Informative
5
PIN
NOTES:
6. VOx = 0.98 * VOx(NOM); Valid for VOx greater than 1.85V.
FN9245.2
April 26, 2006
4
ISL9014
Typical Performance Curves
0.10
0.08
0.06
0.04
0.02
0.00
-0.02
-0.04
-0.06
-0.08
-0.10
0.8
0.6
0.4
VIN = 3.8V
VO = 3.3V
VO = 3.3V
= 0mA
I
LOAD
0.2
-40°C
-40°C
25°C
0.0
-0.2
25°C
85°C
-0.4
-0.6
-0.8
85°C
0
50
100
150
200
250
300
350
400
3.4
3.8
4.2
4.6
5.0
5.4
5.8
6.2
6.6
LOAD CURRENT - I (mA)
O
INPUT VOLTAGE (V)
FIGURE 1. OUTPUT VOLTAGE vs INPUT VOLTAGE
(3.3V OUTPUT)
FIGURE 2. OUTPUT VOLTAGE CHANGE vs LOAD CURRENT
0.10
3.4
VIN = 3.8V
VO = 3.3V
VO = 3.3V
0.08
0.06
0.04
0.02
0.00
-0.02
-0.04
-0.06
I
= 0mA
O
I
= 0mA
LOAD
3.3
3.2
3.1
3.0
2.9
2.8
I
= 150mA
O
I
= 300mA
O
-0.08
-0.10
-40 -25 -10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
3.1
3.6
4.1
4.6
5.1
5.6
6.1
6.5
INPUT VOLTAGE (V)
FIGURE 3. OUTPUT VOLTAGE CHANGE vs TEMPERATURE
FIGURE 4. OUTPUT VOLTAGE vs INPUT VOLTAGE
(3.3V OUTPUT)
2.9
350
300
VO2 = 2.8V
I
= 0mA
O
2.8
2.7
2.6
2.5
2.4
2.3
250
VO = 2.8V
I
= 150mA
O
200
VO = 3.3V
150
100
50
I
= 300mA
O
0
2.6
3.1
3.6
4.1
4.6
5.1
5.6
6.1 6.5
0
50
100
150
200
250
300
350
400
INPUT VOLTAGE (V)
OUTPUT LOAD (mA)
FIGURE 5. OUTPUT VOLTAGE vs INPUT VOLTAGE
(VO2 = 2.8V)
FIGURE 6. DROPOUT VOLTAGE vs LOAD CURRENT
FN9245.2
April 26, 2006
5
ISL9014
Typical Performance Curves (Continued)
55
50
45
40
35
30
25
175
VO1 = 3.3V
150
125
125°C
25°C
85°C
25°C
-40°C
100
75
50
25
0
-40°C
VO1 = 3.3V
VO2 = 2.8V
I
(BOTH CHANNELS) = 0µA
O
3.0
3.5
4.0
4.58
5.0
5.5
6.0
6.5
0
25
50
75
100
125
150
175
200
OUTPUT LOAD (mA)
INPUT VOLTAGE (V)
FIGURE 7. VO1 DROPOUT VOLTAGE vs LOAD CURRENT
FIGURE 8. GROUND CURRENT vs INPUT VOLTAGE
55
50
45
40
200
180
160
140
25°C
85°C
120
100
80
60
40
20
0
-40°C
35
VIN = 3.8V
VIN = 3.8V
VO1 = 3.3V
VO2 = 2.8V
VO = 3.3V
= 0µA
30
25
I
LOAD
BOTH OUTPUTS ON
0
50
100
150
200
250
300
350
400
-40 -25 -10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
LOAD CURRENT (mA)
FIGURE 10. GROUND CURRENT vs TEMPERATURE
FIGURE 9. GROUND CURRENT vs LOAD
VO1 = 3.3V
VO2 = 2.8V
VO2 (10mV/DIV)
5
4
3
2
1
0
I 1 = 300mA
L
VIN = 5.0V
VO1 = 3.3V
VO2 = 2.8V
VIN
VO1
I 2 = 300mA
L
3
I 1 = 300mA
2
1
0
5
0
L
I 2 = 300mA
L
C -1, C -2 = 1µF
L
L
VO2
C
= 0.01µF
BYP
0
100 200 300 400 500 600 700 800 900 1000
TIME (µs)
0
1
2
3
4
5
6
7
8
9
10
TIME (s)
FIGURE 12. TURN-ON/TURN-OFF RESPONSE
FIGURE 11. POWER-UP/POWER-DOWN
FN9245.2
April 26, 2006
6
ISL9014
Typical Performance Curves (Continued)
VO2 = 2.8V
= 300mA
VO = 3.3V
I
LOAD
I
= 300mA
LOAD
C
C
= 1µF
LOAD
= 0.01µF
C
C
= 1µF
LOAD
= 0.01µF
BYP
BYP
4.3V
3.6V
4.2V
3.5V
10mV/DIV
10mV/DIV
400µs/DIV
400µs/DIV
FIGURE 13. LINE TRANSIENT RESPONSE, 3.3V OUTPUT
FIGURE 14. LINE TRANSIENT RESPONSE, 2.8V OUTPUT
100
VIN = 3.6V
90
80
70
60
50
40
30
20
10
0
VO = 1.8V
= 10mA
I
O
VO (25mV/DIV)
C
C
= 0.1μF
BYP
= 1μF
LOAD
VO = 1.8V
VIN = 2.8V
300mA
I
LOAD
100μA
0.1
1
10
100
1000
100μs/DIV
FREQUENCY (kHz)
FIGURE 16. PSRR vs FREQUENCY
FIGURE 15. LOAD TRANSIENT RESPONSE
1000
100
10
VIN = 3.6V
VO = 1.8V
I
= 10mA
LOAD
C
C
C
= 0.1μF
BYP
1
= 1μF
IN
= 1μF
LOAD
0.1
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
FIGURE 17. SPECTRAL NOISE DENSITY vs FREQUENCY
FN9245.2
April 26, 2006
7
ISL9014
Pin Description
PIN
PIN #
NAME
TYPE
DESCRIPTION
1
VIN
Analog I/O
Supply Voltage/LDO Input:
Connect a 1μF capacitor to GND.
2
3
4
EN1
EN2
Low Voltage Compatible
CMOS Input
LDO-1 Enable.
Low Voltage Compatible
CMOS Input
LDO-2 Enable.
CBYP
Analog I/O
Reference Bypass Capacitor Pin:
Optionally connect capacitor of value 0.01μF to 1μF between this pin and GND to tune in the
desired noise and PSRR performance.
5, 7, 8
NC
NC
No Connection
6
9
GND
VO2
Ground
Analog I/O
GND is the connection to system ground. Connect to PCB Ground plane.
LDO-2 Output:
Connect capacitor of value 1μF to 10μF to GND (1µF recommended).
10
VO1
Analog I/O
LDO-1 Output:
Connect capacitor of value 1μF to 10μF to GND (1µF recommended).
Typical Application
ISL9014
10
9
1
2
VIN (2.3-6.5V)
ON
Vout 1
Vout 2
VIN
VO1
VO2
EN1
Enable 1
ON
OFF
8
7
3
4
EN2
NC
NC
Enable 2
OFF
CBYP
6
5
NC
GND
C1
C2
C3
C4
C1, C3, C4: 1μF X5R ceramic capacitor
C2: 0.1μF X5R ceramic capacitor
FN9245.2
April 26, 2006
8
ISL9014
Block Diagram
VIN
IS1
LDO
VREF
TRIM
VO1
VO2
ERROR
1V
VO1
AMPLIFIER
QEN1
~1.0V
LDO-1
LDO-2
EN1
EN2
CONTROL
LOGIC
BANDGAP AND
TEMPERATURE
SENSOR
VOLTAGE
REFERENCE
GENERATOR
1.00V
UVLO
GND
CBYP
mode. During this condition, all on-chip circuits are off, and
the device draws minimum current, typically less than 0.1μA.
When one or both of the enable pins are asserted, the
device first polls the output of the UVLO detector to ensure
that VIN voltage is at least about 2.1V. Once verified, the
device initiates a start-up sequence. During the start-up
sequence, trim settings are first read and latched. Then,
sequentially, the bandgap, reference voltage and current
generation circuitry power up. Once the references are
stable, a fast-start circuit quickly charges the external
reference bypass capacitor (connected to the CBYP pin) to
the proper operating voltage. After the bypass capacitor has
been charged, the LDO’s power up.
Functional Description
The ISL9014 contains all circuitry required to implement two
high performance LDO’s. High performance is achieved
through a circuit that delivers fast transient response to
varying load conditions. In a quiescent condition, the
ISL9014 adjusts its biasing to achieve the lowest standby
current consumption.
The device also integrates current limit protection, smart
thermal shutdown protection, staged turn-on and soft-start.
Smart Thermal shutdown protects the device against
overheating. Staged turn-on and soft-start minimize start-up
input current surges without causing excessive device
turn-on time.
If EN1 is brought high, and EN2 goes high before the VO1
output stabilizes, the ISL9014 delays the VO2 turn-on until
the VO1 output reaches its target level.
Power Control
The ISL9014 has two separate enable pins, EN1 and EN2,
to individually control power to each of the LDO outputs.
When both EN1 and EN2 are low, the device is in shutdown
If EN2 is brought high, and EN1 goes high before VO2 starts
its output ramp, then VO1 turns on first and the ISL9014
FN9245.2
April 26, 2006
9
ISL9014
delays the VO2 turn-on until the VO1 output reaches its
target level.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9014 provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1μF to 10μF output
capacitor that has a tolerance better than 20% and ESR less
than 200mΩ. The design is performance-optimized for a 1μF
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7μF is not recommended as LDO
performance improvement is minimal.
If EN2 is brought high, and EN1 goes high after VO2 starts
its output ramp, then the ISL9014 immediately starts to ramp
up the VO1 output.
If both EN1 and EN2 are brought high at the same time, the
VO1 output has priority, and is always powered up first.
During operation, whenever the VIN voltage drops below
about 1.8V, the ISL9014 immediately disables both LDO
outputs. When VIN rises back above 2.1V, the device re-
initiates its start-up sequence and LDO operation will
resume automatically.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30μs/V to minimize current surge. The
ISL9014 provides short-circuit protection by limiting the
output current to about 475mA.
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter. The filter
includes the external capacitor connected to the CBYP pin.
A 0.01μF capacitor connected CBYP implements a 100Hz
lowpass filter, and is recommended for most high
Each LDO uses an independently trimmed 1V reference. An
internal resistor divider drops the LDO output voltage down
to 1V. This is compared to the 1V reference for regulation.
The resistor division ratio is programmed in the factory.
performance applications. For the lowest noise application, a
0.1μF or greater CBYP capacitor should be used. This filters
the reference noise to below the 10Hz – 1kHz frequency
band, which is crucial in many noise-sensitive applications.
Overheat Detection
The bandgap outputs a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about 145°C, one or both of the
LDO’s momentarily shut down until the die cools sufficiently.
In the overheat condition, only the LDO sourcing more than
50mA will be shut off. This does not affect the operation of
the other LDO. If both LDOs source more than 50mA and an
overheat condition occurs, both LDO outputs are disabled.
Once the die temperature falls back below about 110°C, the
disabled LDO(s) are re-enabled and soft-start automatically
takes place.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider
provides the regulation reference and other voltage
references required for current generation and over-
temperature detection.
The current generator outputs references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
FN9245.2
April 26, 2006
10
ISL9014
Dual Flat No-Lead Plastic Package (DFN)
L10.3x3C
2X
0.10 C
A
10 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE
A
D
MILLIMETERS
2X
0.10
C B
SYMBOL
MIN
0.85
-
NOMINAL
0.90
MAX
0.95
0.05
NOTES
A
A1
A3
b
-
-
-
E
0.20 REF
0.25
-
6
INDEX
AREA
0.20
2.33
1.59
0.30
2.43
1.69
5, 8
D
3.00 BSC
2.38
-
TOP VIEW
B
A
D2
E
7, 8
3.00 BSC
1.64
-
// 0.10
0.08
C
E2
e
7, 8
C
0.50 BSC
-
-
A3
C
SIDE VIEW
k
0.20
0.35
-
-
SEATING
PLANE
L
0.40
0.45
8
N
10
2
D2
D2/2
2
7
8
(DATUM B)
Nd
5
3
Rev. 1 4/06
1
6
NOTES:
INDEX
AREA
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
NX k
E2
(DATUM A)
3. Nd refers to the number of terminals on D.
E2/2
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
NX L
N
N-1
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
NX b
8
e
5
(Nd-1)Xe
REF.
M
0.10
C A B
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
BOTTOM VIEW
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
C
L
9. COMPLIANT TO JEDEC MO-229-WEED-3 except for
dimensions E2 & D2.
(A1)
NX (b)
L
9
5
e
SECTION "C-C"
TERMINAL TIP
FOR ODD TERMINAL/SIDE
C C
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN9245.2
April 26, 2006
11
相关型号:
ISL9014IRCJZ
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRCJZ-T
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRFCZ
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRFDZ
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRFJZ
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRFJZ-T
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10
RENESAS
ISL9014IRFNZ
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229-WEED-3, DFN-10
RENESAS
ISL9014IRFNZ-T
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10, 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229-WEED-3, DFN-10
RENESAS
©2020 ICPDF网 联系我们和版权申明