X9410YV24 [INTERSIL]
Low Noise/Low Power/SPI Bus; 低噪音/低功耗/ SPI总线
| 型号： | X9410YV24 |
| 厂家： | 
Intersil |
| 描述： | Low Noise/Low Power/SPI Bus |
| 文件： | 总21页 (文件大小：375K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
X9410
®
Low Noise/Low Power/SPI Bus
Data Sheet
September 19, 2005
FN8193.1
DESCRIPTION
Dual Digitally Controlled Potentiometer
(XDCP™)
The X9410 integrates two digitally controlled
potentiometers (XDCPs) on a monolithic CMOS
integrated circuit.
FEATURES
• Two potentiometers per package
• SPI serial interface
• Register oriented format
The digitally controlled potentiometer is implemented
using 63 resistive elements in a series array. Between
each element are tap points connected to the wiper
terminal through switches. The position of the wiper on
the array is controlled by the user through the SPI
serial bus interface. Each potentiometer has
associated with it a volatile Wiper Counter Register
(WCR) and four nonvolatile Data Registers (DR0:DR3)
that can be directly written to and read by the user.
The contents of the WCR controls the position of the
wiper on the resistor array through the switches.
Power-up recalls the contents of DR0 to the WCR.
- Direct read/write/transfer wiper positions
- Store as many as four positions per
potentiometer
• Power supplies
- V = 2.7V to 5.5V
CC
- V+ = 2.7V to 5.5V
- V- = -2.7V to -5.5V
• Low power CMOS
- Standby current < 1µA
- High reliability
The XDCP can be used as a three-terminal
potentiometer or as a two-terminal variable resistor in
a wide variety of applications including control,
parameter adjustments, and signal processing.
- Endurance - 100,000 data changes per bit per
register
- Register data retention - 100 years
• 8-bytes of nonvolatile EEPROM memory
• 10kΩ resistor arrays
• Resolution: 64 taps each pot
• 24 Ld SOIC, 24 Ld TSSOP, and 24 Ld plastic DIP
packages
• Pb-free plus anneal available (RoHS compliant)
BLOCK DIAGRAM
VCC
VSS
Pot 0
R0 R1
VH0/RH0
Wiper
Counter
Register
(WCR)
V+
V-
VL0/RL0
R2 R3
HOLD
CS
VW0/RW0
SCK
SO
SI
Interface
and
Control
8
Circuitry
A0
A1
VW1/RW1
Pot 1
Data
WP
R0 R1
R2 R3
V
H1/RH1
Wiper
Counter
Register
(WCR)
Resistor
Array
Pot1
VL1/RL1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X9410
Ordering Information
POTENTIOMETER
TEMP RANGE
(°C)
PART NUMBER
X9410YS24
PART MARKING VCC LIMITS (V) ORGANIZATION (kΩ)
PACKAGE
24 Ld SOIC (300 mil)
X9410YS
5 ±10%
2.5
0 to 70
-40 to 85
0 to 70
X9410YS24I
X9410YS I
X9410YV
24 Ld SOIC (300 mil)
X9410YV24
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld PDIP
X9410YV24Z (Note)
X9410YV24I
X9410YV Z
X9410YV I
X9410YV Z I
X9410WP
0 to 70
-40 to 85
-40 to 85
0 to 70
X9410YV24IZ (Note)
X9410WP24
10
X9410WP24I
X9410WP I
X9410WS
-40 to 85
0 to 70
24 Ld PDIP
X9410WS24*
24 Ld SOIC (300 mil)
X9410WS24I*
X9410WS I
X9410WV
-40 to 85
0 to 70
24 Ld SOIC (300 mil)
X9410WV24*
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld SOIC (300 mil)
X9410WV24Z* (Note)
X9410WV24I*
X9410WV Z
X9410WV I
X9410WV Z I
X9410YS F
X9410YS G
X9410YV F
X9410YV Z F
X9410YV G
0 to 70
-40 to 85
-40 to 85
0 to 70
X9410WV24IZ* (Note)
X9410YS24-2.7
X9410YS24I-2.7
X9410YV24-2.7
X9410YV24Z-2.7 (Note)
X9410YV24I-2.7
2.7 to 5.5
2.5
-40 to 85
0 to 70
24 Ld SOIC (300 mil)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld PDIP
0 to 70
-40 to 85
-40 to 85
0 to 70
X9410YV24IZ-2.7 (Note) X9410YV Z G
X9410WP24-2.7
X9410WP24I-2.7
X9410WS24-2.7*
X9410WS24I-2.7*
X9410WV24-2.7*
X9410WP F
X9410WP G
X9410WS F
X9410WS G
X9410WV F
10
-40 to 85
0 to 70
24 Ld PDIP
24 Ld SOIC (300 mil)
-40 to 85
0 to 70
24 Ld SOIC (300 mil)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm) (Pb-free)
X9410WV24Z-2.7* (Note) X9410WV Z F
X9410WV24I-2.7* X9410WV G
0 to 70
-40 to 85
-40 to 85
X9410WV24IZ-2.7* (Note) X9410WV Z G
*Add "T1" suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN8193.1
2
September 19, 2005
X9410
PIN DESCRIPTIONS
Hos t Interface Pins
Serial Output (SO)
Hardware Write Protect Input (WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked
out by the falling edge of the serial clock.
Analog Supplies (V+, V-)
The analog supplies V+, V- are the supply voltages for
the XDCP analog section.
Serial Input
PIN CONFIGURATION
SI is the serial data input pin. All opcodes, byte
addresses and data to be written to the pots and pot
registers are input on this pin. Data is latched by the
rising edge of the serial clock.
DIP/SOIC
VCC
VL0/RL0
1
2
24
23
22
21
20
19
18
17
16
15
V+
NC
Serial Clock (SCK)
VH0/RH0
VW0/RW0
3
NC
The SCK input is used to clock data into and out of the
X9410.
NC
4
A0
5
CS
WP
SI
SO
6
Chip Select (CS)
X9410
7
HOLD
SCK
When CS is HIGH, the X9410 is deselected and the
SO pin is at high impedance, and (unless an internal
write cycle is underway) the device will be in the
standby state. CS LOW enables the X9410, placing it
in the active power mode. It should be noted that after
a power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
A1
8
VL1/RL1
VH1/RH1
VW1/RW1
9
NC
NC
10
11
12
14
13
NC
V-
VSS
TSSOP
Hold (HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause
the serial communication with the controller without
resetting the serial sequence. To pause, HOLD must
be brought LOW while SCK is LOW. To resume
communication, HOLD is brought HIGH, again while
SCK is LOW. If the pause feature is not used, HOLD
should be held HIGH at all times.
SI
A1
1
2
24
23
22
21
20
19
18
17
16
15
WP
CS
VL1/RL1
VH1/RH1
3
VW0/RW0
VH0/RH0
VL0/RL0
4
5
VW1/RW1
VSS
VCC
NC
NC
NC
6
X9410
NC
NC
NC
7
8
9
Device Address (A - A )
0
1
10
V-
V+
A0
The address inputs are used to set the least significant
2 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
address input in order to initiate communication with
the X9410. A maximum of 4 devices may occupy the
SPI serial bus.
SCK
11
12
14
13
HOLD
SO
Potentiometer Pins
V /R (V /R - V /R ), V /R (V /R - V /R )
H
H
H0 H0
H1 H1
L
L
L0 L0
L1 L1
The V /R and V /R inputs are equivalent to the terminal
H
H
L
L
connections on either end of a mechanical potentiometer.
V /R (V /R - V /R
)
W1 W1
W
W
W0 W0
The wiper outputs are equivalent to the wiper output of
a mechanical potentiometer.
FN8193.1
September 19, 2005
3
X9410
PIN NAMES
Symbol
Wiper Counter Register (WCR)
The X9410 contains two Wiper Counter Registers, one
for each XDCP potentiometer. The WCR is equivalent
to a serial-in, parallel-out register/counter with its
outputs decoded to select one of sixty-four switches
along its resistor array. The contents of the WCR can
be altered in four ways: it may be written directly by the
host via the Write Wiper Counter Register instruction
(serial load); it may be written indirectly by transferring
the contents of one of four associated Data Registers
via the XFR Data Register or Global XFR Data Register
instructions (parallel load); it can be modified one step
at a time by the Increment/ Decrement instruction.
Finally, it is loaded with the contents of its Data Register
zero (DR0) upon power-up.
Description
Serial Clock
SCK
SI, SO
A0 - A1
Serial Data
Device Address
VH0/RH0 - VH1/RH1
,
Potentiometer Pins
(terminal equivalent)
VL0/RL0 - VL1/RL1
VW0/RW0 - VW1/RW1
Potentiometer Pin
(wiper equivalent)
WP
Hardware Write Protection
Analog Supplies
V+,V-
VCC
VSS
NC
System Supply Voltage
System Ground
The Wiper Counter Register is a volatile register; that
is, its contents are lost when the X9410 is powered-
down. Although the register is automatically loaded
with the value in DR0 upon power-up, this may be
different from the value present at power-down.
No Connection
DEVICE DESCRIPTION
The X9410 is
a
highly integrated microcircuit
incorporating two resistor arrays and their associated
registers and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
Data Registers
Each potentiometer has four 6-bit nonvolatile Data
Registers. These can be read or written directly by the
host. Data can also be transferred between any of the
four Data Registers and the associated Wiper Counter
Register. All operations changing data in one of the
Data Registers is a nonvolatile operation and will take
a maximum of 10ms.
Serial Interface
The X9410 supports the SPI interface hardware
conventions. The device is accessed via the SI input
with data clocked in on the rising SCK. CS must be
LOW and the HOLD and WP pins must be HIGH
during the entire operation.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can
be used as regular memory locations for system
parameters or user preference data.
The SO and SI pins can be connected together, since
they have three state outputs. This can help to reduce
system pin count.
Data Register Detail
(MSB)
D5
(LSB)
D0
Array Description
The X9410 is comprised of two resistor arrays. Each
array contains 63 discrete resistive segments that are
connected in series. The physical ends of each array
are equivalent to the fixed terminals of a mechanical
D4
NV
D3
NV
D2
NV
D1
NV
NV
NV
potentiometer (V /R and V /R inputs).
H
H
L
L
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(V /R ) output. Within each individual array only one
W
W
switch may be turned on at a time.
These switches are controlled by a Wiper Counter
Register (WCR). The six bits of the WCR are decoded
to select, and enable, one of sixty-four switches.
FN8193.1
4
September 19, 2005
X9410
Figure 1. Detailed Potentiometer Block Diagram
(One of Two Arrays)
Serial Data Path
Serial
Bus
Input
VH/RH
From Interface
Circuitry
C
o
u
n
t
Register 0
Register 2
Register 1
8
6
Parallel
Bus
Input
e
r
Wiper
D
e
c
o
d
e
Register 3
Counter
Register
(WCR)
INC/DEC
Logic
If WCR = 00[H] then VW/RW = VL/RL
UP/DN
UP/DN
If WCR = 3F[H] then VW/RW = VH/RH
VL/RL
Modified SCL
CLK
VW/RW
Write in Process
The remaining two bits in the ID byte must be set to 0.
The contents of the Data Registers are saved to
nonvolatile memory when the CS pin goes from LOW
to HIGH after a complete write sequence is received
by the device. The progress of this internal write
operation can be monitored by a Write In Process bit
(WIP). The WIP bit is read with a Read Status
command.
Figure 2. Identification Byte Format
Device Type
Identifier
0
1
0
1
0
0
A1
A0
INSTRUCTIONS
Device Address
Identification (ID) Byte
Instruction Byte
The first byte sent to the X9410 from the host,
following a CS going HIGH to LOW, is called the
Identification byte. The most significant four bits of the
slave address are a device type identifier, for the
X9410 this is fixed as 0101[B] (refer to Figure 2).
The next byte sent to the X9410 contains the
instruction and register pointer information. The four
most significant bits are the instruction. The next four
bits point to one of the two pots and when applicable
they point to one of four associated registers. The
format is shown below in Figure 3.
The two least significant bits in the ID byte select one
of four devices on the bus. The physical device
address is defined by the state of the A - A input
0
1
pins. The X9410 compares the serial data stream with
the address input state; a successful compare of both
address bits is required for the X9410 to successfully
continue the command sequence. The A - A inputs
0
1
can be actively driven by CMOS input signals or tied to
or V
V
.
SS
CC
FN8193.1
5
September 19, 2005
X9410
Figure 3. Instruction Byte Format
Five instructions require a three-byte sequence to
complete. These instructions transfer data between the
host and the X9410; either between the host and one of
the data registers or directly between the host and the
Wiper Counter Register. These instructions are:
Register
Select
I3
I2
I1
I0
R1 R0
0
P0
– Read Wiper Counter Register—read the current
wiper position of the selected pot,
Pot Select
Instructions
– Write Wiper Counter Register—change current
wiper position of the selected pot,
The four high order bits of the instruction byte specify
the operation. The next two bits (R and R ) select one
– Read Data Register—read the contents of the
selected data register;
1
0
of the four registers that is to be acted upon when a
– Write Data Register—write a new value to the
selected data register.
register oriented instruction is issued. The last bit (P )
selects which one of the two potentiometers is to be
affected by the instruction.
0
– Read Status—This command returns the contents
of the WIP bit which indicates if the internal write
cycle is in progress.
Four of the ten instructions are two bytes in length and
end with the transmission of the instruction byte.
These instructions are:
The sequence of these operations is shown in Figure 5
and Figure 6.
– XFR Data Register to Wiper Counter Register—This
transfers the contents of one specified Data Register
to the associated Wiper Counter Register.
The final command is Increment/Decrement. It is
different from the other commands because it’s length
is indeterminate. Once the command is issued, the
master can clock the selected wiper up and/or down in
one resistor segment steps, thereby providing a fine
tuning capability to the host. For each SCK clock pulse
– XFR Wiper Counter Register to Data Register—This
transfers the contents of the specified Wiper
Counter Register to the specified associated Data
Register.
– Global XFR Data Register to Counter Register—This
transfers the contents of both specified Data Registers
to the associated Wiper Counter Registers.
(t
) while SI is HIGH, the selected wiper will move
HIGH
one resistor segment towards the V /R terminal.
H
H
Similarly, for each SCK clock pulse while SI is LOW,
the selected wiper will move one resistor segment
– Global XFR Wiper Counter Register to Data Regis-
ter—This transfers the contents of both Wiper
Counter Registers to the specified associated Data
Registers.
towards the V /R terminal. A detailed illustration of the
L
L
sequence and timing for this operation are shown in
Figures 7-8.
The basic sequence of the two byte instructions is
illustrated in Figure 4. These two-byte instructions
exchange data between the WCR and one of the data
registers. A transfer from a Data Register to a WCR is
essentially a write to a static RAM, with the static RAM
controlling the wiper position. The response of the
wiper to this action will be delayed by t
. A transfer
WRL
from the WCR (current wiper position), to a data
register is a write to nonvolatile memory and takes a
minimum of t
to complete. The transfer can occur
WR
between one of the two potentiometers and one of its
associated registers; or it may occur globally, where
the transfer occurs between both potentiometers and
one associated register.
FN8193.1
6
September 19, 2005
X9410
Figure 4. Two-Byte Instruction Sequence
CS
SCK
SI
0
1
0
1
0
0
A1 A0 I3 I2
I1 I0 R1 R0
0
P0
Figure 5. Three-Byte Instruction Sequence (Write)
CS
SCL
SI
0
0
0
1
0
1
A1 A0
I3 I2
I1 I0 R1 R0
0
P0
0
0
D5 D4 D3 D2 D1 D0
Figure 6. Three-Byte Instruction Sequence (Read)
CS
SCL
SI
Don’t Care
0
0
0
1
0
1
A1 A0
I3 I2
I1 I0 R1 R0
0
P0
S0
0
0
D5 D4 D3 D2 D1 D0
Figure 7. Increment/Decrement Instruction Sequence
CS
SCK
SI
0
1
0
1
0
0
A1 A0
I3 I2
I1 I0
0
0
0
P0
I
I
D
E
C
1
I
D
E
C
n
N
C
1
N
C
2
N
C
n
FN8193.1
September 19, 2005
7
X9410
Figure 8. Increment/Decrement Timing Limits
tWRID
SCK
SI
Voltage Out
VW/RW
INC/DEC CMD Issued
Table 1. Instruction Set
Instruction Set
Instruction
I
I
I
I
R
R
P
P
0
Operation
3
2
1
0
1
0
1
Read Wiper Counter Register
1
1
1
1
1
0
0
0
1
1
0
1
1
0
0
1
0
1
0
1
0
0
0
P0 Read the contents of the Wiper Counter
Register pointed to by P0
Write Wiper Counter Register
Read Data Register
0
0
0
0
0
0
P0 Write new value to the Wiper Counter Register
pointed to by P0
R1 R0
R1 R0
R1 R0
P0 Read the contents of the Data Register pointed
to by P0 and R1 - R0
Write Data Register
P0 Write new value to the Data Register pointed to
by P0 and R1 - R0
XFR Data Register to Wiper
Counter Register
P0 Transfer the contents of the Data Register
pointed to by R1 - R0 to the Wiper Counter
Register pointed to by P0
XFR Wiper Counter Register
to Data Register
1
0
1
1
0
0
1
0
0
0
1
0
R1 R0
R1 R0
R1 R0
0
0
0
P0 Transfer the contents of the Wiper Counter
Register pointed to by P0 to the Register
pointed to by R1 - R0
Global XFR Data Register to
Wiper Counter Register
0
Transfer the contents of the Data Registers
pointed to by R1 - R0 of both pots to their
respective Wiper Counter Register
Global XFR Wiper Counter
Register to Data Register
0
Transfer the contents of all Wiper Counter
Registers to their respective data Registers
pointed to by R1 - R0 of both pots
Increment/Decrement Wiper
Counter Register
0
0
0
1
1
0
0
1
0
0
0
0
0
0
P0 Enable Increment/decrement of the Wiper
Counter Register pointed to by P0
Read Status (WIP bit)
1
Read the status of the internal write cycle, by
checking the WIP bit.
FN8193.1
September 19, 2005
8
X9410
Instruction Format
Notes: (1) “A1 ~ A0”: stands for the device addresses sent by the master.
(2) WPx refers to wiper position data in the Counter Register
(2) “I”: stands for the increment operation, SI held HIGH during active SCK phase (high).
(3) “D”: stands for the decrement operation, SI held LOW during active SCK phase (high).
Read Wiper Counter Register (WCR)
device type
identifier
device
addresses
instruction
opcode
WCR
addresses
wiper position
(sent by X9410 on SO)
CS
CS
Falling
Edge
Rising
Edge
W W W W W W
0 0 P P P P P P
A A
P
0
0
1
0
1
0
0
1
0
0
1
0
0
0
1
0
5
4 3 2 1 0
Write Wiper Counter Register (WCR)
device type
identifier
device
addresses
instruction
opcode
WCR
addresses
Data Byte
(sent by Host on SI)
CS
CS
Falling
Edge
Rising
Edge
W W W W W W
0 P P P P P P
A A
P
0
0
1
0
1
0
0
1
0
1
0
0
0
0
0
1
0
5
4 3 2 1 0
Read Data Register (DR)
device type
identifier
device
addresses
instruction DR and WCR
opcode addresses
Data Byte
(sent by X9410 on SO)
CS
CS
Falling
Edge
Rising
Edge
W W W W W W
0 0 P P P P P P
A A
R
1
R
0
P
0
0
1
0
1
0
0
1
0
1
1
0
1
0
5
4 3 2 1 0
Write Data Register(DR)
device type
identifier
device
addresses
instruction DR and WCR
Data Byte
(sent by host on SI)
opcode
addresses
CS
Falling
Edge
CS
Rising
Edge
HIGH-VOLTAGE
WRITE CYCLE
W W W W W W
0 0 P P P P P P
5 4 3 2 1 0
A A
1 0
R
1
R
0
0
P
0
0 1 0 1 0 0
1 1 0 0
Transfer Data Register (DR) to Wiper Counter Register (WCR)
device type
identifier
device
addresses
instruction DR and WCR
CS
Falling
Edge
CS
Rising
Edge
opcode
addresses
A A
1 0
R
1
R
0
0
P
0
0 1 0 1 0 0
1 1 0 1
FN8193.1
September 19, 2005
9
X9410
Transfer Wiper Counter Register (WCR) to Data Register (DR)
device type
identifier
device
addresses
instruction DR and WCR
opcode addresses
CS
Falling
Edge
CS
Rising
Edge
HIGH-VOLTAGE
WRITE CYCLE
D D
0 A A 1
R
R
0
P
0
0
1
0 1
0
1
1 0
0
1
1
0
Increment/Decrement Wiper Counter Register (WCR)
device type
identifier
device
addresses
instruction
opcode
WCR
increment/decrement
CS
Falling
Edge
CS
Rising
Edge
addresses (sent by master on SDA)
A A
1
P
I/ I/
I/ I/
D D
0
1
0
1
0
0
0
0
1
0
X X
0
.
.
.
.
0
0 D D
Global Transfer Data Register (DR) to Wiper Counter Register (WCR)
device type
identifier
device
addresses
instruction
opcode
DR
addresses
CS
Falling
Edge
CS
Rising
Edge
A A
1
R R
1 0
0
1
0
1
0
0
0
0
0
1
0 0
0
Global Transfer Wiper Counter Register (WCR) to Data Register (DR)
device type
identifier
device
addresses
instruction
opcode
DR
addresses
CS
Falling
Edge
CS
Rising
Edge
HIGH-VOLTAGE
WRITE CYCLE
A A
1 0
R R
0 0
1 0
0 1 0 1 0 0
1 0 0 0
Read Status
device type
identifier
device
addresses
instruction
opcode
wiper
addresses
Data Byte
(sent by X9410 on SO)
CS
CS
Falling
Edge
Rising
Edge
W
I
P
A A
0
1
0
1
0
0
0
1
0
1
0
0
0
1
0
0
0
0
0
0
0
1
0
FN8193.1
10
September 19, 2005
X9410
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias.................... -65°C to +135°C
Storage temperature ......................... -65°C to +150°C
Voltage on SCK, SCL or any address
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
input with respect to V ......................... -1V to +7V
SS
Voltage on V+ (referenced to V ) ........................10V
SS
Voltage on V- (referenced to V ) ........................-10V
SS
(V+) - (V-) ..............................................................12V
Any V .....................................................................V+
H
Any V ......................................................................V-
L
Lead temperature (soldering, 10s) .................... 300°C
I
(10s) ............................................................±12mA
W
RECOMMENDED OPERATING CONDITIONS
Temp
Min.
0°C
Max.
+70°C
+85°C
Device
X9410
Supply Voltage (V ) Limits
CC
Commercial
Industrial
5V ± 10%
-40°C
X9410-2.7
2.7V to 5.5V
ANALOG CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
End to end resistance
Power rating
Min.
Typ.
Max.
±20
50
Unit
%
Test Conditions
RTOTAL
mW
mA
Ω
25°C, each pot
IW
Wiper current
±6
RW
Wiper resistance
150
40
250
Wiper Current = ± 1mA,
VCC = 3V
100
Ω
Wiper Current = ± 1mA,
V
CC = 5V
Vv+
Vv-
Voltage on V+ Pin
Voltage on V- Pin
X9410
+4.5
+2.7
-5.5
-5.5
V-
+5.5
+5.5
-4.5
-2.7
V+
V
X9410-2.7
X9410
V
X9410-2.7
VTERM
Voltage on any VH/RH or VL/RL Pin
Noise
Resolution (4)
V
dBV
-120
1.6
Ref: 1kHz
%
Absolute linearity (1)
Relative linearity (2)
±1
MI(3)
MI(3)
ppm/°C
ppm/°C
pF
Rw(n)(actual) - Rw(n)(expected)
±0.2
Rw(n + 1) - [Rw(n) + MI]
Temperature coefficient of RTOTAL
Ratiometric temp. coefficient
±300
±20
CH/CL/CW Potentiometer capacitances
10/10/25
SeeCircuit #3
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when
used as a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (RH - RL)/63, single pot
(4) Individual array resolution
FN8193.1
September 19, 2005
11
X9410
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Typ.
Max.
Units
Test Conditions
ICC1
VCC supply current (Active)
400
µA
fSCK = 2MHz, SO = Open,
Other Inputs = VSS
ICC2
VCC supply current (Nonvolatile
Write)
1
mA
fSCK = 2MHz, SO = Open,
Other Inputs = VSS
ISB
ILI
VCC current (standby)
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
1
10
µA
µA
µA
V
SCK = SI = VSS, Addr. = VSS
VIN = VSS to VCC
ILO
VIH
VIL
VOL
10
VOUT = VSS to VCC
VCC x 0.7
-0.5
VCC + 0.5
VCC x 0.1
0.4
V
Output LOW voltage
V
IOL = 3mA
ENDURANCE AND DATA RETENTION
Parameter
Minimum endurance
Data retention
Min.
100,000
100
Unit
Data changes per bit per register
years
CAPACITANCE
Symbol
Test
Max.
Unit
pF
Test Conditions
(5)
COUT
Output capacitance (SO)
8
6
VOUT = 0V
VIN = 0V
(5)
CIN
Input capacitance (A0, A1, SI, and SCK)
pF
POWER-UP TIMING
Symbol
Parameter
Min.
Max.
Unit
ms
(6)
tPUR
Power-up to initiation of read operation
Power-up to initiation of write operation
VCC Power-up ramp
1
5
1
5
(6)
tPUW
tR VCC
ms
0.2
50
V/msec
POWER-UP AND POWER-DOWN
EQUIVALENT A.C. LOAD CIRCUIT
There are no restrictions on the power-up or power-
5V
2.7V
down sequencing of the bias supplies V , V+, and V-
CC
provided that all three supplies reach their final values
within 1msec of each other. However, at all times, the
voltages on the potentiometer pins must be less than
V+ and more than V-. The recall of the wiper position
from nonvolatile memory is not in effect until all
supplies reach their final value.
1533Ω
SDA Output
100pF
100pF
FN8193.1
September 19, 2005
12
X9410
A.C. TEST CONDITIONS
Test Circuit #3 SPICE Macro Model
Input pulse levels
VCC x 0.1 to VCC x 0.9
10ns
RTOTAL
Input rise and fall times
Input and output timing level
RH
RL
CL
V
CC x 0.5
CH
CW
10pF
Notes: (5) This parameter is periodically sampled and not 100% tested
(6) tPUR and tPUW are the delays required from the time the
third (last) power supply (VCC, V+ or V-) is stable until
the specific instruction can be issued. These parameters
are periodically sampled and not 100% tested.
10pF
25pF
RW
AC TIMING
Symbol
fSCK
tCYC
tWH
tWL
Parameter
Min.
Max.
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
ns
SSI/SPI clock frequency
SSI/SPI clock cycle time
SSI/SPI clock high time
SSI/SPI clock low time
Lead time
2.0
500
200
200
250
250
50
tLEAD
tLAG
tSU
Lag time
SI, SCK, HOLD and CS input setup time
SI, SCK, HOLD and CS input hold time
SI, SCK, HOLD and CS input rise time
SI, SCK, HOLD and CS input fall time
SO output disable time
tH
50
tRI
2
tFI
2
tDIS
tV
0
0
500
100
SO output valid time
tHO
SO output hold time
tRO
SO output rise time
50
50
tFO
SO output fall time
tHOLD
tHSU
tHH
HOLD time
400
100
100
HOLD setup time
HOLD hold time
tHZ
HOLD low to output in High Z
HOLD high to output in Low Z
100
100
20
tLZ
TI
Noise suppression time constant at SI, SCK, HOLD and CS inputs
CS deselect time
tCS
2
0
0
tWPASU
tWPAH
WP, A0 and A1 setup time
WP, A0 and A1 hold time
FN8193.1
September 19, 2005
13
X9410
HIGH-VOLTAGE WRITE CYCLE TIMING
Symbol
Parameter
Typ.
Max.
Unit
tWR
High-voltage write cycle time (store instructions)
5
10
ms
XDCP TIMING
Symbol
Parameter
Min. Max. Unit
tWRPO
tWRL
Wiper response time after the third (last) power supply is stable
Wiper response time after instruction issued (all load instructions)
10
10
µs
µs
ns
tWRID
Wiper response time from an active SCL/SCK edge (increment/decrement instruction)
450
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
Will change
from Low to
High
May change
from High to
Low
Will change
from High to
Low
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A
Center Line
is High
Impedance
TIMING DIAGRAMS
Input Timing
tCS
CS
tLEAD
tCYC
tLAG
SCK
...
tWH
tRI
tFI
tWL
tSU
tH
...
MSB
LSB
SI
High Impedance
SO
FN8193.1
14
September 19, 2005
X9410
Output Timing
CS
SCK
SO
...
...
tV
tHO
tDIS
MSB
LSB
ADDR
SI
Hold Timing
CS
SCK
SO
tHSU
tHH
...
tRO
tFO
tHZ
tLZ
SI
tHOLD
HOLD
XDCP Timing (for All Load Instructions)
CS
SCK
...
...
tWRL
MSB
LSB
SI
VW/RW
High Impedance
SO
FN8193.1
15
September 19, 2005
X9410
XDCP Timing (for Increment/Decrement Instruction)
CS
SCK
VW/RW
SI
...
tWRID
...
...
ADDR
Inc/Dec
Inc/Dec
High Impedance
SO
Write Protect and Device Address Pins Timing
(Any Instruction)
CS
tWPAH
tWPASU
WP
A0
A1
FN8193.1
16
September 19, 2005
X9410
APPLICATIONS INFORMATION
Basic Configurations of Electronic Potentiometers
VR
VR
VW/RW
I
Three terminal Potentiometer;
Variable voltage divider
Two terminal Variable Resistor;
Variable current
Application Circuits
Noninverting Amplifier
Voltage Regulator
VS
+
–
VO
VIN
VO (REG)
317
R1
R2
Iadj
R1
R2
VO = (1+R2/R1)VS
VO (REG) = 1.25V (1+R2/R1)+Iadj R2
Offset Voltage Adjustment
Comparator with Hysteresis
R1
R2
VS
–
+
VS
VO
100kΩ
–
+
VO
TL072
R1
R2
10kΩ
10kΩ
+12V
VUL = {R1/(R1+R2)} VO(max)
LL = {R1/(R1+R2)} VO(min)
10kΩ
-12V
V
FN8193.1
17
September 19, 2005
X9410
Application Circuits (continued)
Attenuator
Filter
C
VS
+
–
R2
R1
–
R
VO
VS
+
R3
R2
R4
All RS = 10kΩ
R1
G
O = 1 + R2/R1
VO = G VS
-1/2 ≤ G ≤ +1/2
fc = 1/(2πRC)
Inverting Amplifier
Equivalent L-R Circuit
R1
R2
VS
R2
C1
–
+
VS
+
–
VO
R1
ZIN
VO = G VS
G = -R2/R1
R3
ZIN = R2 + s R2 (R1 + R3) C1 = R2 + s Leq
(R1 + R3) >> R2
Function Generator
C
R2
R1
–
+
–
+
R
R
}
}
A
B
frequency ∝ R1, R2, C
amplitude ∝ RA, RB
FN8193.1
18
September 19, 2005
X9410
PACKAGING INFORMATION
24-Lead Plastic, Dual In-Line Package Type P
1.265 (32.13)
1.230 (31.24)
0.557 (14.15)
0.530 (13.46)
Pin 1 Index
Pin 1
0.080 (2.03)
0.065 (1.65)
1.100 (27.94)
Ref.
0.162 (4.11)
0.140 (3.56)
Seating
Plane
0.030 (0.76)
0.015 (0.38)
0.150 (3.81)
0.125 (3.18)
0.110 (2.79)
0.090 (2.29)
0.065 (1.65)
0.040 (1.02)
0.022 (0.56)
0.014 (0.36)
0.625 (15.87)
0.600 (15.24)
0°
Typ. 0.010 (0.25)
15°
NOTE:
1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
FN8193.1
19
September 19, 2005
X9410
PACKAGING INFORMATION
24-Lead Plastic, Small Outline Gull Wing Package Type S
0.393 (10.00)
0.290 (7.37)
0.299 (7.60)
0.420 (10.65)
Pin 1 Index
Pin 1
0.014 (0.35)
0.020 (0.50)
0.598 (15.20)
0.610 (15.49)
(4X) 7°
0.092 (2.35)
0.105 (2.65)
0.003 (0.10)
0.012 (0.30)
0.050 (1.27)
0.050"Typical
0.010 (0.25)
0.020 (0.50)
X 45°
0.050"
Typical
0° - 8°
0.009 (0.22)
0.013 (0.33)
0.420"
0.015 (0.40)
0.050 (1.27)
0.030" Typical
24 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
FN8193.1
September 19, 2005
20
X9410
PACKAGING INFORMATION
24-Lead Plastic, TSSOP, Package Type V
.026 (.65) BSC
.169 (4.3)
.177 (4.5)
.252 (6.4) BSC
.303 (7.70)
.311 (7.90)
.047 (1.20)
.0075 (.19)
.0118 (.30)
.002 (.06)
.005 (.15)
.010 (.25)
Gage Plane
(7.72)
(4.16)
0° - 8°
Seating Plane
.020 (.50)
.030 (.75)
(1.78)
(0.42)
Detail A (20X)
(0.65)
ALL MEASUREMENTS ARE TYPICAL
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8193.1
21
September 19, 2005
相关型号：
X9410YV24-2.7
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24I
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24I-2.7
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24I-2.7
DUAL 2.5K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, 4.40 MM, TSSOP-24Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
RENESAS
X9410YV24IZ
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24IZ-2.7
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24Z
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24Z-2.7
Low Noise/Low Power/SPI BusWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X9410YV24Z-2.7
DUAL 2.5K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, 4.40 MM, GREEN, TSSOP-24Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
RENESAS
X9410_06
Dual Digitally Controlled PotentiometerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
INTERSIL
X94131-V7
THIS DRAWING COVERS A PROPRIETARY LTEN AND IS THE PROPERTY OF MICRO SWITCH, A DIVISION OD HONEYWELLWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
HONEYWELL
X9417WP24
Digital Potentiometer, 2 Func, 10000ohm, 2-wire Serial Control Interface, 64 Positions, CMOS, PDIP24, PLASTIC, DIP-24Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
©2020 ICPDF网 联系我们和版权申明