IS22C011S [ISSI]
Speech Synthesizer, 12.8s, CMOS, PDSO16, 0.300 INCH, PLASTIC, SOP-16;型号: | IS22C011S |
厂家: | INTEGRATED SILICON SOLUTION, INC |
描述: | Speech Synthesizer, 12.8s, CMOS, PDSO16, 0.300 INCH, PLASTIC, SOP-16 贺卡 光电二极管 商用集成电路 |
文件: | 总8页 (文件大小:79K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
IS22C011
8 to 12 SEC INSTANT
VOICE ROM
ISSI
OCTOBER 1998
FEATURES
• 2.4V to 6V single power supply operation
• Low standby current (<5 µA at 3V)
• Auto power-down
• Built-in oscillator, D/A converter, EPROM
• ADPCM data compression
• Optional pop noise elimination function
• COUT pin drives speaker with a transistor
• Development tools support
• VOUT1 and VOUT2 drives buzzer directly
• Sampling rate determined by external resistor
• Holdable and unholdable triggering option
• Industrial temperature available
• Voice length at:
– 8 KHz sampling is 8 seconds
– 6 KHz sampling is 10 seconds
– 5 KHz sampling is 12.8 seconds
• Four trigger pins, S1 to S4 for eight sections
• SBT pin play-all or sequential play-all
• 15 ms debounce suitable for CDs
• IRP interrupt pin stops playback at once
• STP stop pulse comes out after playback
• BUSY signal for CPU control
• Two LEDs flash at 3 Hz interval
GENERAL DESCRIPTION
The IS22C011 is a high-quality voice synthesizer
with capacity from 8 to 12 seconds. A proprietary
ADPCM algorithm is used. The audio message is
stored in a 256K bit on-chip one-time programmable
memory.
TheIS22C011provideswidevoltageoperatingrange
from 2.4V to 6.0V. A pair of PWM output pins, VOUT1
and VOUT2, provide direct drive to a buzzer. Voice
quality is comparable to a speaker output and power
consumption is much lower. This facilitates button
battery applications such as greeting cards.
The IS22C011 eliminates the need for complicated
circuitryinvoiceplaybackbutstillachieveshighvoice
quality. Sounds such as human speech, animal
sounds, musical sounds, and even special effects
can be synthesized. Devices can be cascaded to
achieve longer voice duration. Two devices can be
configured in parallel in order to achieve signal mix-
ingwithoutanexternalmixersospeechcanbemixed
withbackgroundmusiceachfromoneoftwodifferent
chips.
A current output pin, COUT, enables the device to
driveaspeakerthroughalowcostNPNtransistor.No
complex filtering or amplifier circuit is needed. An
automatic ramp-down function eliminates undesired
noise at the end of playback.
Up to eight sections are available and accessible
through the S1 to S4 trigger pins. The SBT trigger pin
can be programmed to playback all eight sections or
sequentially from section 1 to 8. An interrupt pin
(IRP), stop pulse (STP) or BUSY signals provide
handshaking with µP or other IS22C011 devices. All
trigger pins give 15 ms debounce time and are ideal
for CDS applications. Two LED drivers are available,
flashing on and off approximately at 3 Hz. The inter-
nal voltage compensation oscillator requires only
one external resistor. Different sampling frequencies
are determined by the external oscillator resistor
value.
The instant programming nature of the IS22C011
gives a very short turn around time free of NRE
charges usually required with conventional voice
ROMs. Usersnowcanaddavoicesynthesisfunction
as an additional feature to their products even when
production volume is small. As a result, initial invest-
ment is minimal and the risk in the product develop-
ment phase is reduced.
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which
may appear in this publication. © Copyright 1998, Integrated Silicon Solution, Inc.
Integrated Silicon Solution, Inc.
VP001-1I
1
10/01/98
®
IS22C011
ISSI
SEGMENT DECODE
Programmable Options
1
H
L
L
L
2
L
H
L
L
3
L
L
H
L
4
L
L
L
H
5
H
H
L
6
L
7
8
H
L
TheIS22C011providesdifferentcontrolfunctionsfor
user specified applications. They include:
S1
S2
S3
S4
L
L
H
H
L
•
•
•
•
Non-sequence or Sequence play-all
Unholdable or Holdable trigger
H
H
L
L
H
STOP or BUSY signal selection
Automatic ramp-down or no ramp-down
SAMPLE FREQUENCY
3.5
3.0
2.5
R
OSC
2.0
1.5
1.0
0.5
0
(MΩ)
5
6
7
8
9 10 11 12 13 14 15
SAMPLE FREQUENCY (KHz)
Typical Value, Vcc = 4.5V
BLOCK DIAGRAM
OSC
OSCILLATOR
VCC
GND
ADDRESS
SEQUENCER
EPROM
CLOCK
GENERATOR
ADPCM
DECODER
S1
S2
S3
S4
CONTROL
LOGIC
D/A
COUT
SBT
IRP
POP NOISE
REDUCTION
V
V
OUT1
OUT2
BUZZER
BUFFER
LED1
LED2
STP/BUSY
LED
DRIVER
2
Integrated Silicon Solution, Inc.
VP001-1I
10/01/98
®
IS22C011
ISSI
PIN DESCRIPTIONS
PIN CONFIGURATIONS
16-Pin DIP and SOP
LED1
Drives First LED Flash at 3 Hz
PWM Audio Signal Output for Buzzer
VOUT1
STP/BUSY
Generate Busy Signal or 30 ms Pulse after Voice
Playback
LED1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
IRP
SBT
S4
V
OUT1
OUT2
GND
GND
VOUT2
LED2
COUT
Ground
V
Compliment PWM Audio Signal Output for Buzzer
Drives Second LED Flash at 3 Hz
S3
STP/BUSY
LED2
VCC
S2
S1
Current Output from Internal DAC for Speaker
Playback
COUT
OSC
VPP
OSC
Oscillator Resistor Pin to Control Sampling
Frequency
VPP
Program Power Supply, No Connect When Voice
Playback
S1-S4
SBT
Input Switches, Internal Pull LOW, Active HIGH
One Key or Sequential Trigger, Internal Pull LOW,
Active HIGH
IRP
Vcc
Interrupt to Stop Playback, Internal Pull LOW,
Active HIGH
Power Supply Voltage
BONDING DIAGRAM
BONDING PARAMETERS
Pin
1
Name
LED1
VOUT1
VOUT2
GND
STP
LED2
COUT
OSC
VPP
X
Y
5
4
2005
2005
2005
2005
86.25
86.25
86.25
86.25
86.25
86.25
86.25
86.25
2005
2005
2005
2005
1584
1891
2139
2422
2383
2130
1854
1368
1005
637
6
3
2
2
7
8
3
1
4
NC
5
9
16
15
14
13
6
10
11
7
8
Y
12
9
X
10
11
12
13
14
15
16
S1
(0,0)
Note: Substrate must be connected to GND
S2
355
Pad size = 95 µm x 95 µm
Vcc
112
Die size = 2100 µm x 2550 µm
S3
156
S4
468
Note: Programming requires connection to
pins 4, 5, 6, 8, 9, 12, 15, and 16.
SBT
IRP
775
1038
Integrated Silicon Solution, Inc.
VP001-1I
3
10/01/98
®
IS22C011
ISSI
ABSOLUTE MAXIMUM RATINGS(1)
Symbol Parameter
Value
Unit
V
°C
°C
VTERM
TBIAS
TSTG
Terminal Voltage with Respect to GND
Temperature Under Bias
Storage Temperature
–0.5 to +7.0
–40 to +85
–55 to +125
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
DC CHARACTERISTICS
Symbol
VCC
VIH
Parameter Description
Operating Voltage
Input HIGH Voltage
Test Conditions
Min.
2.4
2.5
–0.3
—
—
—
—
—
6
—
—
—
Typ.
3.0
3.0
0
–12
12
–2
–5
5
8
1
—
—
Max.
6.0
3.5
0.3
—
—
—
—
—
10
5
100
5
Unit
V
V
Vcc = 3.0V
Vcc = 2.0V
VIL
Input LOW Voltage
V
IOH
VOUT HIGH Operating Current
VOUT LOW Operating Current
COUT Operating Current
STP HIGH Operating Current
STP LOW Operating Current
LED Output Current
Standby Current
Operating Current
Frequency Stability
Vcc = 3.0V, VOUT = 3.0V
Vcc = 3.0V, VOUT = 0V
Vcc = 3.0V, VCOUT = 0.7V
Vcc = 3.0V, VSTP = 3.0V
Vcc = 3.0V, VSTP = 0V
Vcc = 2.2V – 6.0V
Vcc = 3.0V, I/O Open
Vcc = 3.0V, I/O Open
1 – FOSC(3.5V)/FOSC(3.0V)
mA
mA
mA
mA
mA
mA
µA
µA
%
IOL
ICO
ISTPH
ISTPL
ILED
ISB
IOP
∆F/F
AC SWITCHING CHARACTERISTICS
OPERATING RANGE
Symbol
Parameter Description
Typ.
Unit
Range
Ambient Temp.
Vcc
tDD
tST
Debounce Delay
Stop Pulse Width
15
30
ms
ms
Commercial
Industrial
0°C to +70°C
2.4V to 6.0V
2.4V to 6.0V
–40°C to +85°C
SWITCHING WAVEFORMS
S1 to S4 SEGMENT TRIGGERS. PULSE TRIGGERED.
a. Trigger is shorter than a phrase output
b. Trigger is longer than a phrase output
S1
S2
Phrase 2
Phrase 1
Phrase 2
Phrase 2
COUT
LED
STP
4
Integrated Silicon Solution, Inc.
VP001-1I
10/01/98
®
IS22C011
ISSI
LEVEL TRIGGERED
a. Trigger is shorter than a phrase output
b. Trigger is longer than a phrase output
S1
S2
Phrase 2
Phrase 1
Phrase 2
Phrase 2
COUT
LED
SWITCHING WAVEFORMS
SINGLE BUTTON TRIGGER, NONSEQUENTIAL (SBT)
a. Pulse Triggered
SBT
Phrase 1
Phrase 2
Phrase N
Phrase 1
Phrase N
Phrase 1
C
OUT
b. Level Triggered
SBT
Phrase 1
Phrase 2
Phrase 1
Phrase N
Phrase 1
C
OUT
SINGLE BUTTON TRIGGER, SEQUENTIAL (SBT)
a. Pulse Triggered
SBT
Phrase 1
Phrase 2
Phrase 2
Phrase 2
Phrase N
Phrase 1
C
OUT
b. Level Triggered
SBT
Phrase 1
Phrase 2
Phrase 2
Phrase 2
Phrase N
Phrase 1
C
OUT
Integrated Silicon Solution, Inc.
VP001-1I
5
10/01/98
®
IS22C011
ISSI
APPLICATION CIRCUITS
TYPICAL APPLICATION
VDD
VDD
V
ROSC
ROSC
SP
OUT1
OUT2
OSC
OSC
C
OUT
V
PIEZO
BUZZER
S1
S1
S2
S3
S2
S3
S4
SBT
IRP
S4
SBT
IRP
VSS
VSS
CASCADE APPLICATION
VDD
OSC
VCC
OSC
ROSC
ROSC
SP
C
OUT
COUT
SBT
IRP
SBT
IRP
STP
VSS
VSS
6
Integrated Silicon Solution, Inc.
VP001-1I
10/01/98
®
IS22C011
ISSI
APPLICATION CIRCUITS
PARALLEL APPLICATION
Vcc
Vcc
ROSC
ROSC
SP
OSC
OSC
COUT
COUT
S1
S2
S1
S2
S3
S4
S3
S4
SBT
IRP
SBT
IRP
GND
GND
LED APPLICATION
VDD
ROSC
SP
OSC
C
OUT
S1
S2
S3
S4
SBT
IRP
LED2
LED1
VSS
Notes:
The following are typical values:
1. ROSC = 2.0 MΩ.
2. ß OF N (NPN transistor) > 130.
3. SP = 8Ω. 1/4W.
4. Piezo buzzer resonant frequency = 1 KHz.
Integrated Silicon Solution, Inc.
VP001-1I
7
10/01/98
®
IS22C011
ISSI
ORDERING INFORMATION
Commerical Range: 0°C to +70°C
Order Part No.
IS22C011X
IS22C011P
IS22C011S
Package
Unpackaged
300-mil Plastic DIP
300-mil Plastic SOP
Industrial Range: –40°C to +85°C
Order Part No.
IS22C011XI
IS22C011PI
IS22C011SI
Package
Unpackaged
300-mil Plastic DIP
300-mil Plastic SOP
NOTICE
Integrated Silicon Solution, Inc., reserves the right to make changes to the products contained in this publication
in order to improve design, performance or reliability. Integrated Silicon Solution, Inc. assumes no responsibility
for the use of any circuits described herein, conveys no license under any patent or other right, and makes no
representation that the circuits are free of patent infringement. Charts and schedules contained herein reflect
representative operating parameters, and may vary depending upon a user's specific application. While the
information in this publication has been carefully checked, Integrated Silicon Solution, Inc. shall not be liable for
any damages arising as a result of any error or omission.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications
where the failure or malfunction of the product can reasonably be expected to cause failure of the life support
system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications
unless Integrated Silicon Solution, Inc. receives written assurances, to its satisfaction, that: (a) the risk of injury
or damage has been minimized; (b) the user assumes all such risks; and (c) potential liability of Integrated Silicon
Solution, Inc. is adequately protected under the circumstances.
Copyright 1998 Integrated Silicon Solution, Inc.
Reproduction in whole or in part, without the prior written consent of Integrated Silicon Solution, Inc., is prohibited.
®
ISSI
Integrated Silicon Solution, Inc.
2231 Lawson Lane
Santa Clara, CA 95054
Tel: 1-800-379-4774
Fax: (408) 588-0806
e-mail: sales@issiusa.com
http://www.issiusa.com
相关型号:
©2020 ICPDF网 联系我们和版权申明