DANE-25S-L2-E03-A190 概述
Eurostyle D Subminiature Connectors 欧瑞士达ð类微型连接器
DANE-25S-L2-E03-A190 数据手册
通过下载DANE-25S-L2-E03-A190数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Eurostyle D Subminiature Connectors
Cannon
Introduction
Eurostyle D Subminiature Connectors
The D Subminiature Eurostyle connector is a
The main applications will be found in industrial
as well as in telecommunication equipment.
The major advantage for the end user is to
achieve additional space due to the low profile
configuration.
The D Subminiature Eurostyle connectors are
fully mateable with all standard D Subminiature
connectors according to DIN 41652.
Introduction
product line extension of the well known
D Subminiature family originally invented by
ITT Industries, Cannon.
It is a special low profile 90° solder pin
connector acc. to the CECC75 301 802
European specification. It replaces the D*
version with the code 1AEN which was not
100% in line with above mentioned
specification.
ꢀ Meets European Eurostyle specification CECC75 301 802
ꢀ Available in all common layouts (9, 15, 25, 37-way), male and female
ꢀ Available in Performance Classes 1, 2 and 3 according to DIN 41652
ꢀ Clinch nut with M3 or4-40 UNC thread
Product features
ꢀ Jack Post with M3 or 4-40 UNC thread
Materials and Finishes
Shell
Technical Data
Steel, tin plated
Insulator
Contacts
Boardlock / Grounding Insert
Thermoplastic, UL 94V-0
Copper alloy, gold over nickel plated
Brass, tin plated
Threaded insert
Steel, tin plated
Electrical Data
Current rating
5 A / 25°C, 3,5 A / 70°C ambient
temperature
Test voltage
Insulation resistance
Contact resistance
1000 V ac rms at sea level
5 G Ω min.
25 mΩ
Mechanical Data
Polarizing
Number of contacts
Termination method
CECC 75301802
Keystone shaped front shell
9, 15, 25 and 37
Solder pin 90° Eurostyle acc.
Performance class 3 (Standard)
Performance class 2
Performance class 1
Operating temperature
50 mating cycles (without code)
200 mating cycles (code -A191)
500 mating cycles (code -A190)
- 55°C to 125°C
Dimensions are shown in mm
Dimensions subject to change
Cannon
www.ittcannon.com
2
Eurostyle D Subminiature Connectors
Order Reference
D A N E - 15 S - L 1 - E 03 - *
Order Reference Explanation
Series Prefix
Cannon designation
Shell size
E - 9 way
A - 15 way
B - 25 way
C - 37 way
Class
N - new generation
Termination / Mounting
E - 90° pushfit / row spacing 2,54
F - 90° pushfit / row spacing 2,84
Number of contacts
9, 15, 25, 37
Contact gender
P - pin contact
S - socket contact
Contact termination
L - solder pin
Pushfit Type
0 - no pushfit
1 - for pcb 1,6
2 - for pcb 2,4
3 - for pcb 3,2
Mounting height
E - Euro 3,6
Locking
03 - M3 thread
04 - 4-40 UNC thread
13 - M3 thread with jackpost
14 - 4-40 UNC thread with jackpost
Modification
no code - performance class 3
A191 - performance class 2
A190 - performance class 1
Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
Dimensions are shown in mm
Dimensions subject to change
Cannon
www.ittcannon.com
3
Eurostyle D Subminiature Connectors
Pin Connector
Part numbers Pin
Pin Connector 90°
Shell size Layout
Clinch nut 4-40 UNC
DENE-9P-L1-E04-A191
DANE-15P-L1-E04-A191
DBNE-25P-L1-E04-A191
DCNE-37P-L1-E04-A191
Clinch nut M3
DE
DA
DB
DC
9
DENE-9P-L1-E03-A191
DANE-15P-L1-E03-A191
DBNE-25P-L1-E03-A191
DCNE-37P-L1-E03-A191
15
25
37
Shell size Layout
Jackpost 4-40 UNC
Jackpost M3
DE
DA
DB
DC
9
DENE-9P-L1-E14-A191
DANE-15P-L1-E14-A191
DBNE-25P-L1-E14-A191
DCNE-37P-L1-E14-A191
DENE-9P-L1-E13-A191
DANE-15P-L1-E13-A191
DBNE-25P-L1-E13-A191
DCNE-37P-L1-E13-A191
15
25
37
Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
Note: For performance class 1 replace A-191 by -A190;
For performance class 3 delete -A191.
Example: DENE-9P-L1-E13
For row spacing 2,84 mm replace D*NE with D*NF
Example: DANF-15P-L1-A191
Shell size
Contacts
A - 0,7
31,20
39,50
53,40
69,70
B + 0,25
16,79
C ± 0,1
25,00
33,35
47,04
63,50
D + 0,25
8,23
E - 0,7
12,90
12,90
12,90
12,90
F
DE
DA
DB
DC
9
15
25
37
2,54 or 2,84
2,54 or 2,84
2,54 or 2,84
2,54 or 2,84
25,12
8,23
38,84
8,23
55,30
8,23
pushfit
clinch nut
Jackpost
03 - M3 thread
04 - 4-40 UNC thread
13 - M3 thread
14 - 4-40 UNC thread
Dimensions are shown in mm
Dimensions subject to change
Cannon
www.ittcannon.com
4
Eurostyle D Subminiature Connectors
Socket Connector
Part numbers Socket
Socket Connector 90°
Shell size
Layout Clinch nut 4-40 UNC
Clinch nut M3
DE
DA
DB
DC
9
DENE-9S-L1-E04-A191
DANE-15S-L1-E04-A191
DBNE-25S-L1-E04-A191
DCNE-37S-L1-E04-A191
DENE-9S-L1-E03-A191
DANE-15S-L1-E03-A191
DBNE-25S-L1-E03-A191
DCNE-37S-L1-E03-A191
15
25
37
Shell size
Layout Jackpost 4-40 UNC
Jackpost M3
DE
DA
DB
DC
9
DENE-9S-L1-E14-A191
DANE-15S-L1-E14-A191
DBNE-25S-L1-E14-A191
DCNE-37S-L1-E14-A191
DENE-9S-L1-E13-A191
DANE-15S-L1-E13-A191
DBNE-25S-L1-E13-A191
DCNE-37S-L1-E13-A191
15
25
37
Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
Note: For performance class 1 replace A-191 by -A190;
For performance class 3 delete -A191.
Example: DENE-9S-L1-E13
For row spacing 2,84 mm replace D*NE with D*NF
Example: DANF-15S-L1-A191
Shell size
Contacts
A - 0,7
31,20
39,50
53,40
69,70
B - 0,25
16,46
24,79
38,50
54,96
C ± 0,1
25,00
33,35
47,04
63,50
D - 0,25
8,02
E - 0,7
12,90
12,90
12,90
12,90
F
DE
DA
DB
DC
9
2,54 or 2,84
2,54 or 2,84
2,54 or 2,84
2,54 or 2,84
15
25
37
8,02
8,02
8,02
pushfit
clinch nut
Jackpost
03 - M3 thread
04 - 4-40 UNC thread
13 - M3 thread
14 - 4-40 UNC thread
Dimensions are shown in mm
Dimensions subject to change
Cannon
www.ittcannon.com
5
Eurostyle D Subminiature Connectors
Pattern Hole
Contact Arrangements
Face View Pin Insert
PC Board Hole pattern - 90°European
Standard
Shell size
E
Dimension X
Contact arrangement
Contact size
9
20
Termination / Mounting
E - 90° pushfit / row spacing 2,54, F - 90° pushfit / row spacing 2,84
Shell size
A
Dimension X
Contact arrangement
Contact size
15
20
Termination / Mounting
E - 90° pushfit / row spacing 2,54, F - 90° pushfit / row spacing 2,84
Shell size
B
Dimension X
Contact arrangement
Contact size
25
20
Termination / Mounting
E - 90° pushfit / row spacing 2,54, F - 90° pushfit / row spacing 2,84
Dimension X
Termination / Mounting
E - 90° pushfit / row spacing 2,54, F - 90° pushfit / row spacing 2,84
Shell size
Contact arrangement
Contact size
C
37
20
Signal
Contact
0,60
Recommended PCB
Hole
1,00
Mounting
Type
All
Recommended PCB
Hole
3,10
Dimensions are shown in mm
Dimensions subject to change
Cannon
www.ittcannon.com
6
Product Safety Information
presence of combustible materials and this may Do not permit untrained personnel to wire,
release noxious fumes. Overheating may not be assemble or tramper with connectors. For
visually apparent. Burns may result from touching operation voltage please see appropriate natio-
THIS NOTE SHOULD BE READ IN CON-
JUNCTION WITH THE PRODUCT DATA SHEET/
CATALOGUE. FAILURE TO OBSERVE THE
ADVICE IN THIS INFORMATION SHEET AND
THE OPERATING CONDITIONS SPECIFIED IN
THE PRODUCT DATA SHEET/CATALOGUE
COULD RESULT IN HAZARDOUS SITUATIONS.
overheated components.
nal regulations.
3. HANDLING
IMPORTANT GENERAL INFORMATION.
Care must be taken to avoid damage to any
component parts of electrical connectors during 1. Air and creepage paths/Operating voltage
installation and use. Although there are normally The admissible operating voltages depend on the
no sharp edges, care must be taken when handling individual applications and the valid national and
1. MATERIAL CONTENT AND PHYSICAL
FORM
Electrical connectors do not usually contain
hazardous materials. They contain conducting and
non-conducting materials and can be divided into
two groups.
certain components to avoid injury to fingers.
Electrical connectors may be damaged in transit
other applicable safety regulations.
to the customers, and damage may result in For this reason the air and creepage path data
creation of hazards. Products should therefore be are only reference values. Observe reduction of
examined prior to installation/use and rejected if air and creepage paths due to PC board and or
found to be damaged.
harnessing.
a) Printed circuit types and low cost audio types
which employ all plastic insulators and casings.
4. DISPOSAL
2. Temperature
Incineration of certain materials may release All information given are temperature limits. The
b) Rugged, Fire Barrier and High Reliability types
with metal casings and either natural rubber,
synthetic rubber, plastic or glass insulating
materials.
noxious or even toxic fumes.
operation temperature depends on the individual
application.
5. APPLICATION
Connectors with exposed contacts should not be 3. Other important information
selected for use on the current supply side of an Cannon continuously endeavours to improve their
electrical circuit, because an electric shock could products. Therefore, Cannon products may
result from touching exposed contacts on an deviate from the description, technical data and
unmated connector. Voltages in excess of 30 V ac shape as shown in this catalogue and data sheets.
or 42.5 V dc are potentially hazardous and care
Contact materials vary with type of connector and
also application and are usually manufactured from
either copper, copper alloys, nickel, alumel,
chromel or steel. In special applications, other
alloys may be specified.
should be taken to ensure that such voltages can
not be transmitted in any way to exposed metal
parts of the connector body. The connector and
wiring should be checked, before making live, to
2. FIRE CHARACTERISTICS AND ELECTRIC
SHOCK HAZARD
There is no fire hazard when the connector is
correctly wired and used within the specified
parameters. Incorrect wiring or assembly of
the connector or careless use of metal tools
or conductive fluids, or transit damage to any
of the component parts may cause electric
shock or burns. Live circuits must not be
broken by separating mated connectors as this
may cause arcing, ionisation and burning.
Heat dissipation is greater at maximum resistance
in a circuit. Hot spots may occur when resistance
is raised locally by damage, e.g. cracked or
deformed contacts, broken strands of wire. Local
overheating may also result from the use of the
incorrect application tools or from poor quality
soldering or slack screw terminals. Overheating
may occur if the ratings in the Product Data Sheet/
Catalogue are exceeded and can cause breakdown
of insulation and hence electric shock.
have no damage to metal parts or insulators, no
solder blobs, loose strands, conducting lubricants,
swarf, or any other undersired conducting
particles. Circuit resistance and continuity check
should be made to make certain that there are no
high resistance joints or spurious conducting paths.
Always use the correct application tools as
specified in the Data Sheet / Catalogue.
ITT Cannon, a division of ITT Industries, Inc. manufactures the highest quality products available in the marketplace; however
these products are intended to be used in accordance with the specifications in this publication. Any use or application that
deviates from stated operating specifications is not recommended and may be unsafe. No information and data contained in this
publication shall be construed to create any liability on the part of Cannon. Any new issue of this publication shall automatically
invalidate and supersede any and all previous issues. A limited warranty applies to Cannon products. Except for obligations
assumed by Cannon under this warranty, Cannon shall not be liable for any loss, damage, cost of repairs, incidental or
consequential damages of any kind, whether or not based on express or implied warranty, contract, negligence or strict
liability arising in connection with the design, manufacture, sale, use or repair of the products. Product availability, prices
and delivery dates are exclusively subject to our respective order confirmation form; the same applies to orders based on
development samples delivered. This publication is not to be construed as an offer. It is intended merely as an invitation to make
an offer. By this publication, Cannon does not assume responsibility or any liability for any patent infringements or other rights
of third parties which may result from its use. Reprinting this publication is generally permitted, indicating the source. However,
Cannon's prior consent must be obtained in all cases.
If heating is allowed to continue it intensifies by
further increasing the local resistance through loss
of temper of spring contacts, formation of oxide
film on contacts and wires, and leakage currents
through carbonisation of insulation and tracking
paths. Fire can then result in the
Cannon is a trademark of ITT Industries, Inc
DANE-25S-L2-E03-A190 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
DANE-25S-L2-E03-A191 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L0-E03 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L0-E03-A190 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L0-E03-A191 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L1-E03 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L1-E03-A190 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L1-E03-A191 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L2-E03 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L2-E03-A190 | ITT | Eurostyle D Subminiature Connectors | 获取价格 | |
DANE-37P-L2-E03-A191 | ITT | Eurostyle D Subminiature Connectors | 获取价格 |
DANE-25S-L2-E03-A190 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6