Z8523008VSG [IXYS]
Serial I/O Controller, 2 Channel(s), 0.25MBps, CMOS, PQCC44, GREEN, PLASTIC, LCC-44;
| 型号： | Z8523008VSG |
| 厂家： | 
IXYS CORPORATION |
| 描述： | Serial I/O Controller, 2 Channel(s), 0.25MBps, CMOS, PQCC44, GREEN, PLASTIC, LCC-44 通信 时钟 数据传输 外围集成电路 |
| 文件： | 总118页 (文件大小：1752K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Z80230/Z85230/L
Enhanced Serial
Communications Controller
Product Specification
PS005308-0609
Copyright ©2009 by Zilog®, Inc. All rights reserved.
www.zilog.com
Warning:
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A
critical component is any component in a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2009 by Zilog, Inc. All rights reserved. Information in this publication concerning the devices,
applications, or technology described is intended to suggest possible uses and may be superseded. ZILOG,
INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY
OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT.
ZILOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR
TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The information contained within this
document has been verified according to the general principles of electrical and mechanical engineering.
Z8 is a registered trademark of Zilog, Inc. All other product or service names are the property of their
respective owners.
PS005308-0609
Z80230/Z85230/L
Product Specification
iii
Revision History
Each instance in Revision History reflects a change to this document from its previous
revision. For more details, refer to the corresponding pages and appropriate links in the
table below.
Revision
Date
Level
Description
Page No
all
June 2009
May 2009
May 2009
08
Removed Security Watermark from pages
Minor update to page 107
07
107
06
system update change only - no technical
content revised
n/a
Mar 2009
05
Updated document to add 3V product
information
Misc
Removed ISO/BSI certification information
Figure 1, 7 and 23 changed 5V to Vcc
Added Z8523L DC Characteristics
Updated Read and Write AC Characteristics
Updated System Timing Characteristics
Updated General Timing Diagram
Ordering Information updated
ii
2, 13, 76
78
90
98
94
107
75
78
Updated Standard Test Conditions
Updatred Table 43
Updated Table 49 - min value
98
June 2008
04
Updated as per new template and Style Guide. All
Updated Figure 4.
3
September 2007 03
November 2002 02
Updated Figure 38 and Implemented Style
Guide
All
Editorial Updates
Original Issue
All
All
August 2001
01
PS005308-0609
Revision History
Z80230/Z85230/L
Product Specification
iv
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pin Descriptions 1
Pins Common to Both Z85230/L and Z80230 . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin Descriptions Exclusive to the Z85230/L . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Descriptions Exclusive to the Z80230 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description 8
Input/Output Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ESCC Data Communications Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Z80230/Z85230/L Enhancements 22
4-Byte Transmit FIFO Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8-Byte Receive FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Write Register 7 PRIME (WR7’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CRC Reception in SDLC Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TxD Forced High in SDLC with NRZI Encoding When Marking Idle . . . . . . 26
Improved Transmit Interrupt Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DPLL Counter Tx Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Read Register 0 Status Latched During Read Cycle . . . . . . . . . . . . . . . . . 27
Software Interrupt Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Fast SDLC Transmit Data Interrupt Response . . . . . . . . . . . . . . . . . . . . . . 28
SDLC FIFO Frame Status Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FIFO Enable/Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FIFO Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FIFO Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SDLC Status FIFO Anti-Lock Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programming 32
Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Write Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Read Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Z80230 Interface Timing 70
Z80230 Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Z80230 Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Z80230 Interrupt Acknowledge Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . 71
Z85230/L Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Z85230/L Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
PS005308-0609
Table of Contents
Z80230/Z85230/L
Product Specification
v
Z85230/L Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Z85230/L Interrupt Acknowledge Cycle Timing . . . . . . . . . . . . . . . . . . . . . . 74
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics 75
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Standard Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Z85230/L AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Z80230/Z85230/L Errata 99
IUS Problem Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
IUS Problem Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RTS Problem Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
RTS Problem Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Automatic TxD Forced High Problem Description . . . . . . . . . . . . . . . . . . . 102
Automatic TxD Forced High Problem Solutions . . . . . . . . . . . . . . . . . . . . 103
SDLC FIFO Overflow Problem Description . . . . . . . . . . . . . . . . . . . . . . . . 103
SDLC FIFO Overflow Problem Solution . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Default RR0 Value Problem Description . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Default RR0 Value Problem Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Default RR10 Value Problem Description . . . . . . . . . . . . . . . . . . . . . . . . . 104
Default RR10 Value Problem Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
CRC Problem Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
CRC Problem Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Information 105
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information 107
Z8523L (3.3V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Z85230 (5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Part Number Suffix Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
PS005308-0609
Table of Contents
Z80230/Z85230/L
Product Specification
1
Pin Descriptions
The Enhanced Serial Communication Controller (ESCC) pins are divided into seven func-
tional groups:
1. Address/Data
2. Bus Timing and Reset
3. Device Control
4. Interrupt
5. Serial Data (both channels)
6. Peripheral Control (both channels)
7. Clocks (both channels)
Figure 1 on page 2 and Figure 2 on page 2 display the pins in each functional group for
both the Z80230 and Z85230/L. The pin functions are unique to each bus interface version
in the Address/Data group, Bus Timing and Reset group, and Device Control group.
The Address/Data group consists of the bidirectional lines used to transfer data between
the CPU and the ESCC (addresses in the Z80230 are latched by AS). The direction of
these lines depends on whether the operation is a Read or a Write operation.
The Timing and Control groups designate the type of transaction to occur and the timing
of the occurrence. The interrupt group provides inputs and outputs for handling and prior-
itizing interrupts. The remaining groups are divided into Channel A and Channel B groups
for:
•
•
•
Serial Data (Transmit or Receive)
Peripheral Control (such as DMA or modem)
Input and Output Line for the Receive and Transmit Clocks
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
2
Serial
Data
D7
D6
TxDA
RxDA
D5
D4
D3
D2
D1
D0
RD
WR
A/B
CE
TRxCA
RTxCA
SYNCA
W/REQA
DTR/REQA
RTSA
Channel
Clocks
Data Bus
Channel A
Channel
Controls
for modem,
DMA and
Other
CTSA
Bus Timing
and Reset
DCDA
TxDB
RxDB
Z85230/L
Serial
Data
Control
D/C
INT
INTACK
IEI
TRxCB
RTxCB
SYNCB
W/REQB
DTR/REQB
RTSB
Channel
Clocks
Channel B
Interrupt
Channel
Controls
for modem,
DMA and
Other
IEO
CTSB
DCDB
+VccGND PCLK
Figure 1. Z85230/L Pin Functions
Serial
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
AS
TxDA
RxDA
Data
TRxCA
RTxCA
SYNCA
W/REQA
DTR/REQA
RTSA
Channel
Clocks
Channel A
Data Bus
Channel
Controls
for modem,
DMA and
Other
CTSA
Bus Timing
and Reset
DS
DCDA
TxDB
RxDB
Z80230
Serial
Data
R/W
CS1
CS0
INT
INTACK
IEI
Control
TRxCB
RTxCB
SYNCB
W/REQB
DTR/REQB
RTSB
Channel
Clocks
Channel B
Interrupt
Channel
Controls
for modem,
DMA and
Other
IEO
CTSB
DCDB
+VCCGND PCLK
Figure 2. Z80230 Pin Functions
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
3
Figure 3 displays the Z85230/L DIP and PLCC pin assignments, respectively. Figure 4
displays the Z80230 DIP and PLCC pin assignments.
1
40
D1
D3
D0
D2
D5
D4
6
1
40
39
IEO
IEI
7
D7
A/B
D6
INT
RD
CE
D/C
N/C
GND
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
INTACK
VCC
W/REQA
SYNCA
RTxCA
RxDA
IEO
WR
IEI
A/B
INTACK
VCC
CE
Z85230/L
D/C
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
DTR/REQA
RTSA
CTSA
DCDA
PCLK
GND
Z85230
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
DTR/REQB
RTSB
CTSB
DCDB
TRxCA
TxDA
N/C
17
18
29
28
20
21
Z85230 DIP Pin Assignments
Z85230/L PLCC Pin Assignments
Figure 3. Z85230/L Pin Assignments
40
AD1
AD3
AD5
AD7
INT
IEO
IEI
AD0
1
AD2
AD4
AD6
6
7
1
40
39
IEO
IEI
INTACK
VCC
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
R/W
CS0
CS1
N/C
DS
AS
R/W
CS0
INTACK
VCC
W/REQA
SYNCA
RTxCA
RxDA
TRxCA
TxDA
GND
CS1
Z80230
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
GND
Z80230
W/REQB
SYNCB
RTxCB
RxDB
TRxCB
TxDB
DTR/REQB
RTSB
CTSB
N/C
29
28
17
18
DTR/REQA
RTSA
CTSA
DCDA
PCLK
20
21 DCDB
Z80230 DIP Pin Assignments
Z80230 PLCC Pin Assignments
Figure 4. Z80230 Pin Assignments
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
4
Pins Common to Both Z85230/L and Z80230
The pin descriptions for pins common to both Z85230/L and Z80230 are provided below:
CTSA, CTSB (Clear To Send (Inputs, Active Low))—These pins function as transmitter
enables if they are programmed for AUTO ENABLE (WR3 bit 5 is 1), in which case a
Low on each input enables the respective transmitter. If not programmed as AUTO
ENABLE,the pins may be used as general-purpose inputs. These pins are Schmitt-trigger
buffered to accommodate slow rise-time inputs. The ESCC detects pulses on these pins
and may interrupt the CPU on both logic level transitions.
DCDA, DCDB (Data Carrier Detect (Inputs, Active Low))—These pins function as
receiver enables if they are programmed for AUTO ENABLE (WR3 bit 5 is 1); otherwise,
they are used as general-purpose input pins. The pins are Schmitt-trigger buffered to
accommodate slow rise-time signals. The ESCC detects pulses on these pins and may
interrupt the CPU on both logic level transitions.
RTSA, RTSB (Request To Send (Outputs, Active Low))—The RTS pins can be used as
general-purpose outputs or with the AUTO ENABLE feature. When AUTO-ENABLE is
off, these pins follow the inverse state of WR5 bit 1. When used with the AUTO-
ENABLE feature in ASYNCHRONOUS mode, this pin immediately goes Low when
WR5 bit 1 is 1. When WR5 bit 0 is 0, this pin remains Low until the transmitter is empty.
In Synchronous Data Link Control (SDLC) mode, the RTS pins can be programmed to be
deasserted when the closing flag of the message clears the TxD pin, if WR7’ bit 2 is 1,
WR10 bit 2 is 0, and WR5 bit 1 is 0.
SYNCA, SYNCB (Synchronization (Inputs Or Outputs, Active Low))—These pins can
act either as inputs, outputs, or as part of the crystal oscillator circuit. In the ASYNCHRO-
NOUS RECEIVE mode (crystal oscillator option not selected), these pins are inputs simi-
lar to CTS and DCD. In this mode, transition on these lines affect the state of the SYNC/
HUNT status bits in Read Register 0 but have no other function.
In EXTERNAL SYNCHRONIZATION mode, with the crystal oscillator not selected,
these lines also act as inputs. In this mode, SYNC is driven Low, two Rx clock cycles after
the last bit of the SYNC character is received. Character assembly begins on the rising
edge of the receive clock immediately preceding the activation of SYNC.
In the INTERNAL SYNCHRONIZATION mode (MONOSYNC and BISYNC) with the
crystal oscillator not selected, these pins act as outputs. These outputs go Low each time a
SYNC pattern is recognized, regardless of character boundaries. In SDLC mode, pins
switch from input to output when MONOSYNC, BISYNC, or SDLC is programmed in
WR4 and SYNC modes are enabled.
DTR/REQA, DTR/REQB (Data Terminal Ready/Request (Output, Active Low))—
These pins can be programmed (WR14 bit 2) to serve either as general-purpose outputs or
as DMA Request lines. When programmed for DTR function (WR14 bit 2 is 0), these out-
puts follow the inverse of the DTR bit of Write Register 5 (WR5 bit 7). When pro-
grammed for REQUEST mode these pins serve as DMA Requests for the transmitter.
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
5
When used as DMA Request line (WR14 bit 2 is 1), the timing for the deactivation request
can be programmed in Write Register 7’(WR7’) bit 4. If this bit is 1, the DTR/REQ pin is
deactivated with the same timing as the W/REQ pin. If 0, the deactivation timing of DTR/
REQ pin is four clock cycles, the same as in the Z80C30/Z85C30.
W/REQA, W/REQB (Wait/request (Output, Open-drain When Programmed For WAIT
Function, Driven High And Low When Programmed For Request Function))—These
dual-purpose outputs may be programmed as REQUEST lines for a DMA controller or as
WAIT lines to synchronize the CPU to the ESCC data rate. The reset state is WAIT.
RxDA, RxDB (Receive Data (inputs, active High))—These inputs receive serial data at
standard Transistor-Transistor Logic (TTL) levels.
RTxCA, RTxCB (Receive/Transmit Clocks (Input, Active Low))—These pins can be
programmed to several modes of operation. In each channel, RTxC may supply the fol-
lowing:
•
•
•
Receive clock and/or the transmit clock
Clock for the baud rate generator (BRG)
Clock for the Digital Phase-Locked Loop
These pins can also be programmed for use with the respective SYNC pins as a crystal
oscillator. The receive clock may be 1, 16, 32, or 64 times the data rate in ASYNCHRO-
NOUS modes.
TxDA, TxDB (Transmit Data (Output, Active High))—These output transmit serial data
at standard TTL levels.
TRxCA, TRxCB (Transmit/Receive Clocks (Input or Output, Active Low))—These
pins can be programmed in several different modes. When configured as an input, the
TRxC may supply the receive clock and/or the transmit clock. When configured as an out-
put, TRxC can echo the clock output of the Digital Phase-Locked Loop, the crystal oscilla-
tor, the BRG or the transmit clock.
PCLK (Clock (Input))—This clock is the master ESCC clock used to synchronize internal
signals. PCLK is a TTL level signal. PCLK is not required to have any phase relationship
with the master system clock.
IEI (Interrupt Enable In (Input, Active High))—IEI is used with IEO to form an interrupt
daisy chain when there is more than one interrupt-driven device. A High IEI indicates that
no higher priority device has an Interrupt Under Service (IUS) or is requesting an
interrupt.
IEO (Interrupt Enable Out (Output, Active High))—IEO is High only if IEI is High and
the CPU is not servicing an ESCC interrupt. During an Interrupt Acknowledge Cycle, IEO
is also driven Low if the ESCC is requesting an interrupt. IEO can be connected to the
next lower priority device’s IEI input, and in this case inhibits interrupts from lower prior-
ity devices.
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
6
INT (Interrupt (Output, Open-Drain, Active Low))—This pin activates when the ESCC
requests an interrupt. The INT is an open-drain output.
INTACK (Interrupt Acknowledge (Input, Active Low))—This pin is a strobe which indi-
cates that an Interrupt Acknowledge Cycle is in progress. During this cycle, the ESCC
interrupt daisy chain is resolved. The device can return an interrupt vector that may be
encoded with the type of interrupt pending. During the acknowledge cycle, if IEI is High,
the ESCC places the interrupt vector on the data bus when RD goes active for the Z85230/
L, or when DS goes active for the Z80230. INTACK is latched by the rising edge of
PCLK.
Pin Descriptions Exclusive to the Z85230/L
The pin description for pins exclusive to Z85230/L is provided below:
Pins D7–D0 (Data Bus (Bidirectional, tristate))—These pins carry data and commands
to and from the Z85230/L.
CE (Chip Enable (Input, Active Low))—This pin selects the Z85230/L for a Read or
Write operation.
RD ((Read (input, Active Low))—This pin indicates a Read operation and, when the
Z85230/L is selected, enables the Z85230/L’s bus drivers. During the Interrupt Acknowl-
edge cycle, RD gates the interrupt vector onto the bus if the Z85230/L is the highest prior-
ity device requesting an interrupt.
WR (Write (Input, Active Low))—When the Z85230/L is selected, this pin denotes a
Write operation, which indicates that the CPU writes command bytes or data to the
Z85230/L write registers.
WR and RD going Low simultaneously is interpreted as a Reset.
Note:
A/B (Channel A/Channel B (Input))—This pin selects the channel in which the Read or
Write operation occurs. A High selects Channel A and a Low selects Channel B.
D/C (Data/Control Select (Input))—This signal defines the type of information trans-
ferred to or from the Z85230/L. A High indicates data transfer and a Low indicates a com-
mand transfer.
Pin Descriptions Exclusive to the Z80230
The pin description for pins exclusive to Z80230 is provided below:
AD7–AD0 (Address/Data Bus (Bidirectional, Active High, tristate))—These multi-
plexed lines carry register addresses to the Z80230 as well as data or control information
to and from the Z80230.
R/W (Read/Write (Input, Read Active High))—This pin specifies if the operation to be
performed is a Read or Write operation.
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
7
CS0 (Chip Select 0 (Input, Active Low))—This pin is latched concurrently with the
addresses on A7-A0 and must be Low for the intended bus transaction to occur.
CS1 (Chip Select 1 (Input, Active High))—This second chip select pin must be High
before and during the intended bus transaction.
DS (Data Strobe (Input, Active Low))—This pin provides timing for the transfer of data
into and out of the Z80230. If AS and DS are both Low, this condition is interpreted as a
RESET.
AS (Address Strobe (Input, Active Low))—Addresses on A7-A0 are latched by the ris-
ing edge of this signal.
PS005308-0609
Pin Descriptions
Z80230/Z85230/L
Product Specification
8
Functional Description
The architecture of the ESCC is described based on its functionality as a:
•
•
Data communications device, which transmits and receives data in a wide variety of
protocols
Microprocessor peripheral, in which the ESCC offers valuable features such as
vectored interrupts and DMA support
The details of the communication between the receive and transmit logic of the system bus
are displayed in Figure 5 and Figure 6 on page 9. The features and data path for each of
the ESCC A and B channels are identical. For more information on SCC/ESCC and ISCC
Family of Products, refer to the respective User Manuals available for download from
www.zilog.com.
Internal Data Bus
to Other Channel
TX FIFO
4 Bytes
WR8
Internal TXD
WR7
WR6
SYNC Register
SYNC Register
Final Tx
MUX
TXD
Shift Register
20-Bit TX
ASYNC
SYNC
SDLC
Transmit
MUX and
2 Bit Delay
NRZI Encode
Zero Insert
CRC-SDLC
Transmit Clock
CRC-Gen
From Receiver
Figure 5. ESCC Transmit Data Path
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
9
CPU I/O
I/O Data Buffer
Internal Data Bus
Status FIFO
10 x 19 Frame
Lower Byte (WR12)
Time Constant
Rx Error FIFO
8 Bytes Deep
Rx Data FIFO
8 Bytes Deep
Upper Byte (WR13)
Time Constant
16 Bit Down Counter
BRG
Output
BRG
Input
Div 2
Rec. Error Logic
14 Bit Counter
Hunt Mode (BISYNC)
SYNC
CRC
DPLL IN
SYNC Register
and 0 Delete
Receive Shift
Register
DPLL
OUT
DPLL
Internal TXD
3 Bits
CRC Delay
Register (8 Bits)
NRZI
Decode
MUX
1 Bit
RxD
MUX
CRC Checker
To Transmit Section
CRC Result
SDLC-CRC
Figure 6. ESCC Receive Data Path
Input/Output Capabilities
System communication to and from the ESCC is accomplished using the
ESCC register set. There are 17 Write registers and 16 Read registers. Many of the fea-
tures on the ESCC are enabled through a new register in the ESCC: Write Register 7
Prime (WR7’). This new register can be accessed if bit 0 or WR15 is set to 1. Table 1 on
page 10 lists the Write registers and a brief description of their functions. Table 2 on page
11 lists the Read Registers.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
10
Throughout this document the Write and Read registers are referenced with the notations
WR for Write Register and RR for Read Register. For example:
Note:
WR4A – Write Register 4 for Channel A
RR3 – Read Register 3 for either or both channels
Table 1. ESCC Write Registers
Write Register
Functions
WR0
Command Register; Select Shift Left/Right Mode, Cyclic
Redundancy Check (CRC) Initialization, and Resets for
Various Modes
WR1
WR2
WR3
WR4
WR5
WR6
WR7
WR7’
WR8
WR9
Interrupt Conditions, Wait/DMA Request Control
Interrupt Vector, Accessed Through Either Channel
Receive and Miscellaneous Control Parameters
Transmit and Receive Parameters and Modes
Transmit Parameters and Controls
SYNC Character or SDLC Address Field
SYNC Character or SDLC Flag
SDLC Enhancements Enable, Accessible if WR15 bit D0 is 1
Transmit FIFO, 4-Bytes Deep
Reset Commands and Master INT Enable, Accessible
Through Either Channel
WR10
WR11
WR12
WR13
WR14
Miscellaneous Transmit and Receive Controls
Clock Mode Control
Lower Byte of BRG Time Constant
Upper Byte of BRG Time Constant
Miscellaneous Controls and Digital Phase-Locked Loop
(DPLL) Commands
WR15
External Interrupt Control
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
11
Table 2. ESCC Read Registers
Register Name
RR0
Functions
Transmit, Receive, and External Status
Special Receive Condition Status Bits
Unmodified Interrupt Vector
Modified Interrupt Vector
RR1
RR2A
RR2B
RR3A
RR4
Interrupt Pending Bits
WR4 Mirror, if WR7’ bit D6 equals 1
WR5 Mirror, if WR7’ bit D6 equals 1
RR5
RR6
SDLC Frame LSB Byte Count, if WR15 bit D2 equals 1
RR7
SDLC Frame 10 X 19 FIFO Status and MSB Byte Count, if
WR15 bit DS equals 1
RR8
Receive Data FIFO, 8 Bits Deep
WR9 Mirror, if WR7’ bit D6 Equals 1
Miscellaneous Status Bits
RR9
RR10
RR11
RR12
RR13
RR14
RR15
WR11 Mirror, if WR7’ bit D6 Equals 1
Lower Byte of BRG Time Constant
Upper Byte of BRG Time Constant
WR14 Mirror, if WR7’ bit D6 Equals 1
WR 15 Mirror, if WR7’ bit D6 Equals 1
There are three modes used to move data into and out of the ESCC:
1. POLLING
2. INTERRUPT (vectored and non-vectored)
3. BLOCK TRANSFER
The BLOCK TRANSFER mode can be implemented under CPU or DMA control.
POLLING
When POLLING, data interrupts are disabled, three registers in the ESCC are automati-
cally updated whenever any function is performed. For example, end-of-frame (EOF) in
SDLC mode sets a bit in one of these status registers. The purpose of POLLING is for the
CPU to periodically read a status register until the register contents indicate the need that
data requires transfer. RR0 is the only register that must be read to determine if data needs
to be transferred. An alternative to polling RR0 for each channel is to poll the Interrupt
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
12
Pending register. Status information for both channels resides in one register. Only one
register may be read. Depending on its contents, the CPU performs one of the three opera-
tions listed below:
1. Write data
2. Read data
3. Continues processing
Two bits in the register indicate the requirement for data transfer.
INTERRUPT
The ESCC INTERRUPT mode supports vectored and nested interrupts. The fill levels at
which the transmit and receive FIFOs interrupt the CPU are programmable, allowing the
ESCC requests for data transfer to be tuned to the system interrupt response time.
Nested interrupts are supported with the interrupt acknowledge (INTACK) feature of the
ESCC. It allows the CPU to acknowledge the occurrence of an interrupt, and re-enable
higher priority interrupts. Since an INTACK cycle releases the INT pin from the active
state, a higher priority ESCC interrupt or another higher priority device can interrupt the
CPU. When an ESCC responds to INTACK signal from the CPU, it can place an interrupt
vector on the data bus. This vector is written in WR2 and may be read in RR2. To increase
the interrupt response time, the ESCC can modify 3 bits in this vector to indicate status. If
the vector is read in Channel A, status is not included. If it is read in Channel B, status is
included.
Each of the six sources of interrupts in the ESCC (Transmit, Receive, and External/Status
interrupts in both channels) has 3 bits associated with the interrupt source as listed below:
1. Interrupt Pending (IP)
2. Interrupt Under Service (IUS)
3. Interrupt Enable (IE)
If the IE bit is set for a given interrupt source, then that source can request interrupts.
However, when the Master Interrupt Enable (MIE) bit in WR9 is reset, no interrupts can
be requested. The IE bits are write-only. The other two bits are related to the interrupt pri-
ority chain (see Figure 7 on page 13). The ESCC can request an interrupt only when no
higher priority device is requesting an interrupt (that is, when IEI is High). If the device in
question requests an interrupt, it pulls down INT. The CPU then responds with INTACK,
and the interrupting device places a vector on the data bus.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
13
Peripheral
Peripheral
Peripheral
+VCC
IEI A7–A0INT INTACKIEO
IEI A7–A0 INTINTACKIEO IEI A7–A0INTINTACK
+VCC
A7–A0
INT
INTACK
Figure 7. ESCC Interrupt Priority Schedule
The ESCC can also execute an Interrupt Acknowledge cycle using software. Sometimes it
is difficult to create the INTACK signal with the necessary timing to acknowledge inter-
rupts and allow the nesting of interrupts. In such cases, interrupts can be acknowledged
with a software command to the ESCC. For more information, Z80230/Z85230/L
Enhancements on page 22
Interrupt Pending (IP) bits signal a need for interrupt servicing. When an IP bit is 1 and the
IEI input is High, the INT output is pulled Low, requesting an interrupt. In the ESCC, if an
IE bit is not set, then the IP for that source is never set. The IP bits are read in RR3A.
The Interrupt Under Service (IUS) bits signal that an interrupt request is serviced. If IUS is
set to 1, all interrupt sources of low priority in the ESCC and external to the ESCC are pre-
vented from requesting interrupts. The internal interrupt sources are inhibited by the state
of the internal daisy chain, while lower priority devices are inhibited by setting IEO Low
for subsequent peripherals. An IUS bit is set during an Interrupt Acknowledge cycle if
there are no higher priority devices requesting interrupt.
There are three type of interrupts as listed below:
1. Transmit
2. Receive
3. External/Status
Each interrupt type is enabled under program control with Channel A having higher prior-
ity than Channel B, and with Transmit, Receive, and External/Status interrupts prioritized
in that order within each channel. When the Transmit interrupt is enabled (WR1 bit 1 is 1),
the occurrence of the interrupt depends on the state of WR7’ bit 5. If WR7’ bit 5 is 0, the
CPU is interrupted when the top byte of the transmit First In First Out (FIFO) becomes
empty. If WR7’ bit 5 is 1, the CPU is interrupted when the transmit FIFO becomes com-
pletely empty. The transmit interrupt occurs when the data in the exit location of the
Transmit FIFO loads into the Transmit Shift Register and the Transmit FIFO becomes
completely empty. This condition means that there must be at least one character written
to the Tx FIFO for it to become empty.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
14
When the receiver is enabled, the CPU is interrupted in one of the following three meth-
ods:
1. Interrupt on First Receive Character or Special Receive Condition
2. Interrupt on All Receive Characters or Special Receive Conditions
3. Interrupt on Special Receive Conditions Only
If WR7’ bit 3 is 1, and the Special Receive Condition is selected, the Receive character
occurs when there are four bytes available in the Receive FIFO. This is most useful in syn-
chronous applications as the data is in consecutive bytes. Interrupt on First Character or
Special Condition and Interrupt on Special Condition Only are typically used with the
BLOCK TRANSFER mode. A special Receive Condition consists of one of the follow-
ing:
•
•
•
•
Receiver Overrun
Framing error in ASYNCHRONOUS mode
EOF in SDLC mode
Parity error (optional)
The Special Receive Condition interrupt is different from an ordinary receive character
available interrupt only by the status placed in the vector during the Interrupt Acknowl-
edge cycle. In Receive Interrupt on First Character or Special Condition mode, an inter-
rupt occurs from Special Receive Conditions any time after the first receive character
interrupt.
The primary function of the External/Status interrupt is to monitor the signal transitions of
the CTS,DCD, and SYNC pins. However, an External/Status interrupt is also caused by
any of the following:
•
•
•
•
•
A Transmit Underrun condition
A zero count in the BRG
A detection of a Break (ASYNCHRONOUS mode)
An ABORT (SDLC mode)
An End Of Poll (EOP) sequence in the data stream (SDLC LOOP mode)
The interrupt caused by the ABORT or EOP sequence has a special feature that allows the
ESCC to interrupt when the ABORT or EOP sequence is detected or terminated. This fea-
ture facilitates the proper termination of the current message, correct initialization of the
next message, and the accurate timing of the ABORT condition by external logic in SDLC
mode. SDLC LOOP mode allows secondary stations to recognize the primary station and
regain control of the loop during a poll sequence.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
15
CPU/DMA BLOCK TRANSFER
The ESCC provides a BLOCK TRANSFER mode to accommodate CPU/DMA controller.
The BLOCK TRANSFER mode uses the WAIT/REQUEST output in conjunction with the
WAIT/REQUEST bits in WR1. The WAIT/REQUEST output can be defined as a WAIT
line in the CPU BLOCK TRANSFER mode or as a REQUEST line in the DMA BLOCK
TRANSFER mode.
To a DMA controller, the ESCC REQUEST output indicates that the ESCC is ready to
transfer data to or from memory.
To the CPU, the WAIT line indicates that the ESCC is not ready to transfer data, thereby
requesting the CPU to extend the I/O cycle.
The DTR/REQUEST line allows full-duplex operation under DMA control. The ESCC
can be programmed to deassert the DTR/REQUEST pin with the same timing as the
WAIT/REQUEST pin if WR7’ bit 4 is 1.
ESCC Data Communications Capabilities
The ESCC provides two independent full-duplex programmable channels for use in any
common ASYNCHRONOUS or SYNCHRONOUS data communication protocols (see
Figure 8). The channels have identical features and capabilities.
Parity
Start
Stop
Marking Line
Marking Line
Data
Data
Data
Asynchronous
SYNC
Data
Data
CRC1
CRC2
Monosync
Bisync
SYNC
SYNC
Signal
Data
Data
Data
Data
CRC1
CRC1
CRC2
CRC2
CRC2
External Sync
Flag
Address
Control
SDLC/HDLC/X.25
Figure 8. Various ESCC Protocols
Information
CRC1
Flag
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
16
ASYNCHRONOUS Mode
The ESCC has significant improvements over the standard Serial Communications Con-
troller (SCC). The addition of the deeper data FIFOs provide greater protection against
underruns and overruns as well as more efficient use of bus bandwidth. The deeper data
FIFOs are accessible regardless of the protocol used and they need not be enabled. For
information on these improvements, see Z80230/Z85230/L Enhancements on page 22
Send and Receive allow 5 to 8 bits per character, plus optional Even or Odd parity. The
transmitters can supply 1, 1.5, or 2 stop bits per character and can provide break indica-
tion. The receiver break-detection logic interrupts the CPU both at the start and at the end
of a received break. Reception is protected from spikes by start-bit validation that delays
the signal for a length of time equal to one half the time period required to process 1 bit of
data after a Low level is detected on the receive data input (RxDA or RxDB pins). If the
Low level does not persist (that is, a transient), the character assembly process does not
start.
Framing errors and overrun errors are detected and buffered together with the character at
which they occur. Vectored interrupts allow fast servicing of error conditions. Further-
more, a built-in checking process avoids the interpretation of a framing error as a new start
bit. A framing error results in the addition of a delay of one half the amount of time
required to process 1 bit of data at the point at which the search for the next start bit
begins. Transmit and Receive clock can be selected from any of the several sources. In
ASYNCHRONOUS mode, the SYNC pin may be programmed as an input with interrupt
capability.
SYNCHRONOUS Mode
The ESCC supports both byte-oriented and bit-oriented SYNCHRONOUS communica-
tion. SYNCHRONOUS byte-oriented protocols are handled in several modes. They
enable character synchronization with a 6- or 8-bit SYNC character (MONOSYNC) or a
12-bit or 16-bit synchronization pattern (BISYNC), or with an external sync signal. Lead-
ing sync characters are removed without interrupting the CPU.
5- or 7-bit sync characters are detected from 8- or 16-bit patterns in the ESCC by overlap-
ping the larger pattern across multiple incoming sync characters as displayed in Figure 9.
5 Bits
SYNC SYNC
SYNC
8
Data
Data
Data
Data
16
Figure 9. Detecting 5- or 7-Bit Synchronous Characters
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
17
CRC checking for SYNCHRONOUS BYTE-ORIENTED mode is delayed by one charac-
ter time so that the CPU may disable CRC checking on specific characters. This action
permits the implementation of protocols such as IBM BISYNC.
Both CRC-16 (X16 + X15 + X2 + 1) and CRC-CCITT (X16 + X12 + X5 + 1) error checking
polynomials are supported. Either polynomial may be selected in all synchronous modes.
You can preset the CRC generator and checker to all 1s or all 0s. The ESCC also provides
a feature that automatically transmits CRC data when no other data is available for trans-
mission. This feature enables high-speed transmissions under DMA control, with no need
for CPU intervention at the end of a message. When there is no data or CRC to send in the
SYNCHRONOUS mode, the transmitter inserts 6-, 8-, 12-, or 16-bit SYNC characters,
regardless of the programmed character length.
SDLC Mode
The ESCC supports SYNCHRONOUS bit-oriented protocols, such as SDLC and
High-Level Data Link Control (HDLC), by performing automatic flag sending, zero inser-
tion, and CRC generation.
A special command is used to abort a frame which is in transmission. At the end of a mes-
sage, the ESCC automatically transmits the CRC and trailing flag when the transmitter
underruns. The transmitter may also be programmed to send an idle line consisting of con-
tinuous flag characters or a steady marking condition.
If a transmit underrun occurs in the middle of a message, an External/Status interrupt
warns the CPU of this status change so that an Abortcommand can be issued. The ESCC
may also be programmed to send an Abortcommand by itself, in the event of an
underrun, relieving the CPU of the task. The last character of a frame may consist of 1- to
8-bits, allowing reception of frames of any length.
The receiver automatically synchronizes on the leading flag of a frame in SDLC or HDLC
and provides a synchronization signal on the SYNC pin (an interrupt may also be pro-
grammed). The receiver may search for frames addressed by 1-byte or 4-bits within a byte
of a user-specified address or for a global broadcast address. Frames not matching either
the user-selected address or broadcast address are ignored.
The number of address bytes are extended under software control. To receive data, an
interrupt can be selected on the first received character, or on every character, or On Spe-
cial Condition Only (EOF). The receiver automatically deletes all zeros inserted by the
transmitter during character assembly. CRC is also calculated and is automatically
checked to validate frame transmission. At the end of transmission, the status of a received
frame is available in the status registers. In SDLC mode, the ESCC must be programmed
to use the CRC-CCITT polynomial, but the generator and checker may be pre-set to all 1s
or all 0s. The CRC data is inverted before transmission and the receiver checks against the
bit pattern 0001110100001111.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
18
NRZ, NRZI, or FM coding may be used in any 1X mode. The parity options available in
ASYNCHRONOUS mode are also available in SYNCHRONOUS mode. However, parity
checking is not normally used for SDLC because CRC checking is more robust.
SDLC LOOP Mode
The ESCC supports SDLC LOOP mode as well as normal SDLC. In SDLC LOOP mode,
a primary controller station manages the message traffic flow on the loop and any number
of secondary stations. In SDLC LOOP mode, the ESCC performs the functions of a sec-
ondary station. An ESCC operation in regular SDLC mode may act as a controller (see
Figure 10). SDLC LOOP mode is selected by setting WR10 bit 1 to 1.
Controller
Secondary #1
Secondary #4
Secondary #2
Secondary #3
Figure 10. SDLC LOOP mode
A secondary station in an SDLC LOOP mode always monitors the messages sent around
the loop and passes these messages to the rest of the loop, retransmitting them with a one-
bit time delay. The secondary station places its own message in the loop only at specific
times. The controller indicates that the secondary stations can transmit messages by send-
ing a special character, called EOP, around the loop. The EOP character has a bit pattern
11111110, the same pattern as an Abort character in normal HDLC. This bit pattern is
unique and easily recognized, because of the zero insertion in the message.
When a secondary station has a message to transmit and recognizes an EOP on the line, it
changes the last binary 1 of the EOP to a 0 before transmission. This action changes the
EOP into a flag sequence. The secondary station now places its message on the loop and
terminates the message with an EOP. Any secondary stations further down the loop with
messages to transmit appends their messages to the message of the first secondary station
using the same process. Secondary stations without any messages to transmit merely echo
the incoming message. All secondary stations are prohibited from placing messages on the
loop except upon recognizing an EOP. In SDLC LOOP mode, NRZ, NRZI or FM coding
can be used.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
19
SDLC Status FIFO
The ESCC’s ability to receive high speed back-to-back SDLC frames is maximized by a
10-bit deep by 19-bit wide status FIFO buffer. When enabled (through WR15 bit 2 is 1),
the storage area enables DMA to continue data transfer into the memory, so that the CPU
examines the message later. For each SDLC frame, 14 counter bits and 5 Status/Error bits
are stored. The byte count and status bits are accessed through Read Registers, RR6, and
RR7. RR6 and RR7 are only used when the SDLC FIFO buffer is enabled. The 10 x 19
status FIFO buffer is separate from the 8-byte receive data FIFO buffer.
Baud Rate Generator
Each channel in the ESCC contains a programmable BRG. Each generator consists of two
8-bit registers that form a 16-bit time constant, a 16-bit down counter, and a flip-flop on
the output, producing a square wave. At start-up, the flip-flop at the output is set High, the
value in the time constant register is loaded into the counter, and the count down begins.
When the BRG reaches zero, the output toggles, the counter is reloaded with the time con-
stant, and the process repeats. The time constant can be changed at any time, but the new
value does not take effect until the counter is loaded again.
The output of the BRG may be used as the Transmit clock, the Receive clock, or both. The
output can also drive the DPLL. For more information, see Digital Phase-Locked Loop.
If the receive clock or the transmit clock is not programmed to come from the TRxC pin,
the output of the BRG may be echoed out by the TRxC pin.
The following formula relates the time constant to the baud rate. PCLK or RTxC is the
clock input to the BRG. The clock mode is 1, 16, 32, or 64, as selected in WR 4 bits 6 and
7.
PCLK or RTxC Frequency
Time Constant =
-2
2(Baud Rate) (Clock Mode)
Digital Phase-Locked Loop
The ESCC contains a DPLL to recover clock information from a data stream with NRZI or
FM encoding. The DPLL is driven by a clock that is nominally 32 (NRZI) or 16 (FM)
times the data rate. The DPLL uses this clock, along with the data stream, to construct a
clock for the data. This clock is then used as the ESCC receive clock, the transmit clock,
or both. When the DPLL is selected as the transmit clock source, it provides a jitter-free
clock output. The clock output is the DPLL input frequency divided by the appropriate
divisor for the selected encoding technique.
For NRZI encoding, the DPLL counts the 32x clock to create nominal bit times. As the
32x clock is counted, the DPLL searches the incoming data stream for edges (either 1 to 0
or 0 to 1). When a transition is detected the DPLL makes a count adjustment (during the
next counting cycle), producing a terminal count closer to the center of the bit cell.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
20
For FM encoding, the DPLL counts from 0 to 32, but with a cycle corresponding to two
bit times. When the DPLL is locked, the clock edges in the data stream occurs between
counts 15 and 16 and between counts 31 and 0. The DPLL looks for edges only during a
time centered on the 15 to 16 counting transition.
The 32x clock for the DPLL can be programmed to come from either the RTxC input or
the output of the BRG. The DPLL output is programmed to be echoed out the ESCC by the
TRxC pin (if this pin is not being used as an input).
Data Encoding
Data encoding allows the transmission of clock and data information over the same
medium. This capability saves the need to transmit clock and data over separate medium
as is normally required tor synchronous data. The ESCC provides four different data
encoding methods, selected by bits 6 and 5 in WR10. Examples of these 4 encoding meth-
ods is displayed in Figure 11. Any encoding method is used in any X1 mode in the ESCC,
ASYNCHRONOUS or SYNCHRONOUS. The data encoding selected is active even if
the transmitter or receiver is idling or disabled.
1
1
0
0
1
0
Data
NRZ
NRZI
FM1
FM0
Figure 11. Data Encoding Methods
Table 3 lists the four encoding methods, their levels, and values.
Table 3. Data Encoding Descriptions
Code Type
Level
Value
NRZ
High
Low
1
0
NRZI
No Change
Change
1
0
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
21
Table 3. Data Encoding Descriptions (Continued)
Code Type Level
Value
FM1 (biphase mark) Additional Transition at the Center of the Bit Cell
1
0
No Additional Transition at the Center of the Bit
Cell
FM0 (biphase
space)
A transition occurs at the beginning of every bit
call. A 0 is represented by an additional transition
at the center of the bit cell.
A 1 is represented by no additional transition at
the center of the bit cell.
0
1
In addition to the four methods, ESCC can be used to decode Manchester (biphase level)
data using DPLL in the FM mode and programming the receiver for NRZ data. Man-
chester encoding always produces a transition at the center of the bit cell. If the transition
is 0 to 1, the bit is a 0. If the transition is 1 to 0, the bit is a 1.
Auto Echo and Local Loopback
The ESCC is capable of automatically echoing everything it receives. This feature is use-
ful mainly in ASYNCHRONOUS modes, but works in SYNCHRONOUS and SDLC
modes as well. AUTO ECHO mode (TxD is RxD) is used with NRZI or FM encoding
with an additional delay because the data stream is not decoded before retransmission. In
AUTO ECHO mode, the CTS input is ignored as a transmitter enable, (although transi-
tions for this input can cause interrupts if programmed to do so). In this mode, the trans-
mitter is actually bypassed and the programmer is responsible for disabling transmitter
interrupts and Wait/Request on transmit.
The ESCC is also capable of LOCAL LOOPBACK. In this mode the internal transmit
data is tied to the internal receive data and RxD is ignored. The CTS and DCD inputs are
also ignored as transmit and receive enables. However, transitions on these inputs can
cause interrupts. LOCAL LOOPBACK works in ASYNCHRONOUS, SYNCHRO-
NOUS, and SDLC modes with NRZ, NRZI, or FM coding of the data stream.
PS005308-0609
Functional Description
Z80230/Z85230/L
Product Specification
22
Z80230/Z85230/L Enhancements
A detailed description of the enhancements to the Z80230/Z85230/L ESCC that differenti-
ate it from the standard SCC is provided below:
4-Byte Transmit FIFO Buffer
The ESCC has a 4-byte transmit buffer with programmable interrupt and DMA request
levels. It is not necessary to enable the FIFO buffer as it is always available. You can set
the Transmit Buffer Empty (TBE) interrupt and DMA Request on Transmit command to
be generated either when the top byte of transmit FIFO is empty or only when the FIFO is
completely empty. A hardware or channel reset clears the transmit shift register, flushes
the transmit FIFO, and sets WR7’ bit 5 to 1.
If the transmitter generates the interrupt or DMA request for data when the top byte of the
FIFO is empty (WR7’ bit 5 is 0), the system allows for a long response time to the data
request without underflowing. The interrupt service routine (ISR) writes 1byte and then
tests RR0 bit 2. The DMA Request on Transmit in this mode is set to 0 after each data
Write (that is, TBE), RR0 bit 2, is set to 1 when the top byte of the FIFO is empty. WR7’
bit 5 resets to 1.
In applications for which the interrupt frequency is important, the transmit ISR can be
optimized by programming the ESCC to generate the TBE interrupt only when the FIFO is
completely empty (WR7’ bit 5 is 1) and, writing 4 bytes to fill the FIFO. When WR7’ bit
5 is 1, only one DMA request is generated, filling the bottom of the FIFO. However, this
may be advantageous for applications where the possible reassertion of the DMA request
is not required. The TBE status bit, RR0 bit 2, is set to 1 when the top byte of the FIFO is
empty. WR7’ bit 5 is set to1 after a hardware or channel reset.
8-Byte Receive FIFO
The ESCC has an 8-byte receive FIFO with programmable interrupt levels. It is not neces-
sary to enable the 8-byte FIFO as it is always available. A hardware or channel reset clears
the Receive Shift register and flushes the Receive FIFO. The Receive Character Available
interrupt is generated as selected by WR7’ bit 3. The Receive Character Available bit,
RR0 bit 0 is set to 1 when at least one byte is available at the top of the FIFO (independent
of WR7’ bit 3).
A DMA Request on Receive, if enabled, is generated whenever 1 byte is available in the
receive FIFO independent of WR7’ bit 3. If more than 1 byte is available in the FIFO, the
Wait/Request pin becomes inactive and becomes active when the FIFO is emptied.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
23
By resetting WR7’ bit 3 to 0, applications which have a long latency to interrupts can gen-
erate the request to read data from the FIFO when one byte is available. The application
can then test the Receive Character Available bit to determine if more data is available.
By setting WR7’ bit 3 to 0, the ESCC can issue an interrupt when the receive FIFO is half
full (4 bytes available), allowing the frequency of interrupts to be reduced. If WR7’ bit 3 is
1, the Receive Character Available interrupt is generated when there are 4 bytes available.
If the ISR reads 4 bytes during each routine, the frequency of interrupts is reduced.
If WR7’ bit 3 is 1 and Receive Interrupt on All Characters and Special Conditions is
enabled, the receive character available interrupt is generated when four characters are
available. However, when a character is detected to have a special condition, an interrupt
is generated when the character is loaded into the top four bytes of the FIFO. Therefore,
the Special Condition ISR must be RR1 before reading the data to determine which byte
has the special condition.
Write Register 7 PRIME (WR7’)
A new register, WR7’, has been added to the ESCC to enable the programming of six new
features. The format of this register is listed in Table 4.
Table 4. Write Register 7 Prime (WR7’)
Bit
7
W
0
6
W
0
5
W
0
4
/W
0
3
W
0
2
W
0
1
W
0
0
W
0
R/W
Reset
Note: R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value Description
7
6
5
4
3
2
1
0
W
W
W
W
W
W
W
W
0
Reserved, must be 0
Extended Read Enable
Transmit FIFO Int Level
DTR/REQ Timing Mode
Receive FIFO Int Level
Auto RTS Deactivation
Auto EOM Reset
Auto Transmit Flag
WR7’ is written by first setting Bit 0 of Write Register 15 (WR15 bit 0) to 1 and then
accessing WR7. All write commands to register 7 are to WR7’ while WR15 bit 0 is set to
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
24
1. WR15 bit 0 must be reset to 0 to address the SYNC character in register WR7. If bit 6 of
WR7’ is set to 1, then WR7’ can be read by performing a read cycle to RR14. The WR7’
features remain enabled until specifically disabled or by a hardware or software reset. Bit
5 is set to 1 and all other bits are reset to 0 after a reset.
For applications which use either the Zilog Z8X30SCC or Z80230, these two device types
can be identified in software with the following test:
1. Write 01Hto Write Register 15
2. Read Register 15
If bit 0 is set to 0, the device is Z8X30SCC. If bit 0 is set to 1, it is a Z80C30. If the device
is Z8XC30, a write to WR15 is required before proceeding. If the device is Z80230, all
writes to address 7 are to WR7’ until WR15 is set to 0.
The WR7 register bits are described below:
Bit 7 (Not used)
This bit must always be 0.
Bit 6 (Extended Read Enable)
Setting this bit to 1 enables WR3, WR4, WR5, WR7’ and WR10 to be read by issuing a
READ command for RR9 (WR3) RR4, RR5, RR14 (WR7’) and RR11 (WR10), respec-
tively.
Bit 5 (Transmit FIFO Interrupt Level)
If this bit is set to 1, the TBE interrupt is generated when the transmit FIFO is completely
empty. If this bit is set to 0, the TBE interrupt is generated when the top byte of the trans-
mit FIFO is empty. This bit is set following a hardware or channel reset.
In DMA REQUEST ON TRANSMIT mode, when using either the W/REQ or DTR/REQ
pins, the request is asserted when the Tx FIFO is completely empty if WR7’ bit 5 is set to
1. The request is asserted when the top byte of the FIFO is empty if bit 5 is reset.
Bit 4 (DTR/REQ Timing)
If this bit is set to 1 and the DTR/REQ pin is used for REQUEST mode (WR14 bit 2 is 1),
the deactivation of the DTR/REQ pin is identical to the W/REQ pin as displayed in
Figure 12 on page 25. If this bit is reset, the deactivation time is 4TcPc.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
25
WR
D7–D0
Transmit Data
WR7 bit 4 =1
WR7 bit 4 = 0
DTR/REQ
WAIT/REQ
Figure 12. DMA Request on Transmit Deactivation Timing
Bit 3 (Receive FIFO Interrupt Level)
This bit sets the interrupt level of the receive FIFO. If this bit is set to 1, the receive data
available bit is asserted when the receive FIFO is half full (4 bytes available). If this bit is
reset to 0, the Receive Data Available interrupt is requested when all bytes are set. For
more information, see 8-Byte Receive FIFO on page 22.
Bit 2 (Automatic RTS Pin Deassertion)
This bit controls the timing of the deassertion of the RTS pin in SDLC mode. If this bit is
1 and WR5 bit 1 is set to 0 during the transmission of an SDLC frame, the deassertion of
the RTS pin is delayed until the last bit of the closing flag clears the TxD pin. The RTS pin
is pulled High after the rising edge of the transmit clock cycle from the last bit of the clos-
ing flag. This action implies that the ESCC must be programmed for Flag on Underrun
(WR10 bit 2 is 0) for the RTS pin to deassert at the end of the frame. This feature works
independently of the programmed Transmitter Idle state. In SYNCHRONOUS mode other
than SDLC, the RTS pin immediately follows the state programmed into WR5 bit 1. When
WR7’ bit 2 is set to 0, the RTS follows the state of WR5 bit 1.
Bit 1 (Automatic EOM Reset)
If this bit is 1, the ESCC automatically resets the Tx Underrun/EOM latch and presets the
transmit CRC generator to its programmed preset state (per values set in WR5 bit 2 and
WR10 bit 7). Therefore, it is not necessary to issue the Reset Tx Underrun/EOM Latch
command when this feature is enabled.
Bit 0 (Automatic Tx SDLC Flag)
If this bit is 1, the ESCC automatically transmits an SDLC flag before transmitting data.
This action removes the requirement to reset the Mark Idle bit (WR10 bit 3) before writing
data to the transmitter.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
26
Historically, the SCC latched the databus on the falling edge of WR. However, as many
CPUs do not guarantee that the databus is valid when the WR pin goes Low, Zilog modi-
fied the databus timing to allow a maximum delay of 20 nS from the WR signal going
active Low to the latching of the databus.
CRC Reception in SDLC Mode
In SDLC mode, the entire CRC is clocked into the receive FIFO. The ESCC completes
clocking in the CRC to allow it to be retransmitted or manipulated software. In the SCC,
when the closing flag is recognized, the contents of the receive shift register are immedi-
ately transferred to the receive FIFO, resulting in the loss of the last two bits of the CRC.
In the ESCC, it is not necessary to program this feature. When the closing flag is detected,
the last 2 bits of the CRC are transferred into the receive FIFO. In all other
SYNCHRONOUS mode, the ESCC does not clock in the last 2 CRC bits (same as the
SCC).
TxD Forced High in SDLC with NRZI Encoding When Marking Idle
When the ESCC is programmed for SDLC mode with NRZI data encoding and Mark Idle
(WR10 bit 6 is 0, bit 5 is 1, bit 3 is 1), the TxD pin is automatically forced High when the
transmitter enters the Mark Idle state. There are several different ways for the transmitter
to enter the Idle state. In each of the following cases the TxD pin is forced High when the
Mark Idle condition is reached:
•
•
•
•
•
Data, CRC, flag, and Idle
Data, flag, and Idle
Data, abort (on underrun), and Idle
Data, abort (command), and Idle
Idle flag and command to Idle Mark
The Force High feature is disabled when the Mark Idle bit is set to 0.
This feature is used in combination with the automatic SDLC opening flag transmission
feature, WR7’ bit 0 is 1, to assure that data packets are formatted correctly. In this case, the
CPU is not required to issue any commands. If WR7’ bit 0 is 0, as on the SCC, the Mark
Idle bit (WR10 bit 3), is set to 1, to enable flag transmission before an SDLC packet trans-
mits.
Improved Transmit Interrupt Handling
The ESCC latches the TBE interrupt because the CRC is loaded into the Transmit Shift
register even if the TBE interrupt, due at the last data byte, has not been reset. The end of a
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
27
synchronous frame is guaranteed to generate two TBE interrupts even if a Reset Transmit
Buffer Interrupt command for the data created interrupt is issued after the CRC interrupt
occurs (Time A in Figure 13). Two ResetTBEcommands are required. The TxIP latches
if the EOM latch resets before the end of the frame.
Data
Data
CRC1
CRC2
Flag
TxBE
Time A
TxIP Bit
TxIP 2
TxIP 1
Figure 13. TxIP Latching
DPLL Counter Tx Clock Source
When the DPLL is selected as the transmit clock source, the DPLL counter output is the
DPLL source clock divided by the appropriate divisor for the programmed data encoding
format. In FM mode (FM0 or FM1), the DPLL counter output signal is the input frequency
divided by 16.
In NRZI mode, the DPLL counter output signal is the input clock cycle divided by 32.
This feature provides a jitter-free output signal that replaces the DPLL transmit clock out-
put as the transmit clock source. This action has no effect on the use of the DPLL as the
receive clock source (see Figure 14).
DPLL CLK
DPLL Output to Receiver
DPLL Output to Transmitter
DPLL
Input
DPLL Counter
Input Frequency Divided by 16 (FM0 or FM1)
Input Clock Cycle Divided by 32 for NRZI
Figure 14. DPLL Outputs
Read Register 0 Status Latched During Read Cycle
The contents of Read Register 0, RR0 is latched during a Read operation. The ESCC pre-
vents the contents of RR0 from changing during a Read operation. But, the SCC allows
the status of RR0 to change while reading the register and may require reading RR0 twice.
The contents of RR0 is updated after the rising edge of RD signal.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
28
Software Interrupt Acknowledge
The Z80230/Z85230/L interrupt acknowledge cycle can be initiated using software. If
Write Register 9 (WR9 bit 5 is 1), Read Register 2 (RR2) results in an interrupt INTACK
cycle, a software acknowledgment causes the INT pin to go High. The IEO pin goes Low.
The Interrupt Under Service (IUS) latch is set to the highest priority pending interrupt.
When a hardware INTACK signal is desired, a software acknowledge cycle requires that a
Reset Highest IUS command be issued in the ISR. If RR2 is read from Channel A, the
unmodified vector is returned. If RR2 is read from Channel B, then the vector is modified
to indicate the source of the interrupt. The Vector Includes Status (VIS) and No Vector
(NV) bits in WR9 are ignored when WR9 bit 5 is set to 1.
If the INTACK and IEI pins are not used, they are pulled up to VCC through a resistor
(2.2 k?, typical).
Fast SDLC Transmit Data Interrupt Response
To facilitate the transmission of back-to-back SDLC frames with a single shared flag
between frames, the ESCC allows data for a second frame to be written to the transmit
FIFO after the Tx Underrun/EOM interrupt occurs. This feature allows application soft-
ware more time to write the data to the transmitter while allowing the current frame to
conclude with CRC and flag. The SCC required that data not be written to the transmitter
until a TBE interrupt is generated after the CRC completed transmission.
If data is written to the transmit FIFO after the Transmit Underrun/EOM interrupt is issued
but before the TBE interrupt is issued, the Automatic EOM Reset function is enabled
(WR7’ bit 1 is 1). Consequently, the commands Reset Tx/Underrun EOM Latch and Reset
Tx CRC Generator must never be used.
SDLC FIFO Frame Status Enhancement
When used with a DMA controller, the ESCC SDLC Frame Status FIFO enhancement
maximizes the ESCC’s ability to receive high-speed, back-to-back SDLC messages. It
minimizes frame overruns due to CPU latencies in responding to interrupts. The feature
(displayed in Figure 15 on page 29) includes:
•
•
•
10-bit deep by 19-bit wide status FIFO
14-bit receive byte counter
Control logic
The 10 x 19 bits status FIFO is separate from the 8-byte receive data FIFO.
When the enhancement is enabled, the status in Read Register 1 (RR1) and byte count for
the SDLC frame are stored in the 10- x 19-bit status FIFO. This action allows the DMA
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
29
controller to transfer the next frame into memory while the CPU verifies the previously
received frame.
Frame Status FIFO Circuitry
Reset on Flag Detect
SCC Status Register
Increment on
Byte Counter
RR1
Residue Bits (3)
Overrun, CRC Error
Each Received Character
Enable Count in SDLC
EOF Signal
Status Read Complete
5 Bits
14 Bits
FIFO Array
10- by 19- Bits
Tail Pointer
4-Bit Counter
Head Pointer
4-Bit Counter
4-Bit Comparator
Equal
Over
8 Bits
EN
5 Bits
EOF=1
6 Bits
6-Bit MUX
6 Bits
RR1
2 Bits
FIFO
Enable
Bit
7
Bit
6
Bits
5-0
RR6
WR15 Bit 2
Set Enables
Status FIFO
Interface
to SCC
RR7 5 - 0 + RR6 7-0
14-Bit Byte Counter
(16 KB Maximum Count)
RR7 Bit 7
FIFO data-available status bit
(1 during read)
RR7 Bit 7
FIFO Overflow Status Bit
(1 on overflow)
See Notes:, next.
Figure 15. SDLC Frame Status FIFO
Notes:
1. All Sent bypasses MUX and equals contents of SCC Status Register.
2. Parity bits bypass MUX and equals contents of SCC Status Register.
3. EOF is set to 1 whenever reading from the FIFO.
Summarizing the operation: Data is received, assembled, and loaded into the 8-byte FIFO
before transferring to memory by the DMA controller.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
30
When a flag is received at the end of an SDLC frame, the frame byte count from the 14-bit
counter and 5 status bits are loaded into the status FIFO for verification by the CPU. The
CRC checker is automatically reset in preparation for the next frame, which starts immedi-
ately.
Because the byte count and status are saved for each frame, the message integrity can be
verified at a later time. Status information for up to ten frames is stored before a status
FIFO overrun occurs.
If a frame is terminated with an Abortcommand, the byte count and status is loaded to
the status FIFO and the counter is reset for the next frame.
FIFO Enable/Disable
This FIFO buffer is enabled when WR15 bit 2 is 1 and the ESCC is in the SDLC/HDLC
mode. Otherwise, the status register contents bypass the FIFO and transfer directly to the
bus interface (the FIFO pointer logic is reset either when disabled or by a channel or
power-on reset). When the FIFO mode is disabled, the ESCC is downward-compatible
with the NMOS Z8030/Z8530. The FIFO mode is disabled on power-up (WR15 bit 2 set
to 0 on reset). The effects of backward compatibility on the register set are that RR4 is an
image of RR0, RR5 is an image of RR1, RR6 is an image of RR2, and RR7 is an image of
RR3. For information on the added registers, see Read Registers on page 53. The status of
the FIFO Enable signal is read at RR15 bit 2. If the FIFO is enabled, the bit is set to 1; oth-
erwise it is reset to 0.
FIFO Read Operation
When WR15 bit 2 is 1 and the FIFO is not empty, the next read status register RR1 or the
additional registers RR7 and RR6, reads the FIFO. Reading status register RR1 causes one
location of the FIFO to empty, so status is read after reading the byte count; otherwise the
count is incorrect. Before the FIFO underflows, it is disabled. In this case, the multiplexer
is switched to allow status to read directly from the status register. In this state, reads from
RR7 and RR6 are undefined bit 6 of RR7 (FIFO data available) status data is coming from
the FIFO or directly from the status register, because it is set to 1 whenever the FIFO is not
empty.
Since all status bits are not stored in the FIFO, the All Sent, Parity, and EOF bits bypass
the FIFO. The status bits sent through the FIFO are the three Residue Bits, Overrun, and
CRC Error.
The correct sequence for polling the byte count and FIFO logic is RR7, RR6, then RR1
(reading RR6 is optional). Additional logic prevents the FIFO from emptying by multiple
reads from RR1. The read from RR7 latches the FIFO empty/full status bit (bit 6) and
steers the status multiplexer to read the ESCC megacell instead of the status FIFO
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
31
(because the status FIFO is empty). The read from RR1 allows an entry to be read from the
FIFO (if the FIFO is empty, the logic prevents a FIFO underflow condition).
FIFO Write Operation
When the end of an SDLC frame is received and the Status FIFO is enabled, the contents
of the status and byte-count registers load into the FIFO. The EOF signal increments the
FIFO. If the FIFO overflows, the RR7 bit 7 (FIFO overflow) is set, indicating the over-
flow. This bit and the FIFO control logic is reset by disabling and re-enabling the FIFO
control bit (WR15 bit 2). For details about FIFO control timing during an SDLC frame,
see Figure 16.
0
F
1
2
3
4
5
6
7
0
F
1
2
3
4
5
6
7
0
F
A
D
D
D
D
C
C
A
D
D
D
D
C
F
C
Internal byte strobe
increments counter
Internal byte strobe
increments counter
Do not load
counter on
first flag.
reset byte
counter here
Reset byte
Reset byte
counter, then
load counter
into FIFO and
increment PTR
counter, then
load counter
into FIFO and
increment PTR.
Figure 16. SDLC Byte Counting Detail
SDLC Status FIFO Anti-Lock Feature
When the Frame Status FIFO is enabled and the ESCC is programmed for Special Receive
Condition Only (WR1 bit 4 = bit 3=1), the data FIFO is not locked when a character with
EOF status is read.When EOF status is at the top of the FIFO, an interrupt with a vector
for receive data is generated. The command ResetHighestIUSmust be issued at the
end of the ISR regardless of whether an Interrupt Acknowledge cycle was executed (hard-
ware or software).
This action allows the DMA to complete the transfer of the received frame to memory,
then interrupt the CPU that a frame was completed, without locking the FIFO. Because in
the RECEIVE INTERRUPT ON SPECIAL CONDITION ONLY mode the interrupt vec-
tor for receive data is not used, it indicates that the last byte of a frame has been read from
the receive FIFO. Reading the frame status (CRC, byte count and other status stored in the
status FIFO) determines that EOF is not required.
When a character with a special receive condition other than EOF is received (receiver
overrun or parity), a special receive condition interrupt is generated after the character is
read from the FIFO and the receive FIFO is locked until the ErrorResetcommand is
issued.
PS005308-0609
Z80230/Z85230/L Enhancements
Z80230/Z85230/L
Product Specification
32
Programming
The ESCC contains write registers in each channel that are programmed by the system
separately to configure the function of each channel.
In the Z85230/L ESCC, the data FIFOs are directly accessible by selecting a High on the
D/C pin. Except WR0 and RR0, programming the write registers requires two write oper-
ations and reading a read register requires a write and a read operation. The first Write is to
WR0 which contains bits that point to the selected register. If the next operation is a Write
the selected write register is written. If the next operation is a read, the selected read regis-
ter is read. The pointer bits are automatically cleared after the second operation so the next
read or write comes from RR0 or goes to WR0. It is not necessary to write 00 to WR0 to
access WR0 or RR0.
For the Z80230 ESCC, the registers are directly addressable. A command issued to WR0B
determines how the ESCC decodes the address placed on the address/data bus at the
beginning of a Read or Write cycle. In Shift Right mode the channel select A/B is taken
from AD0 and the state of AD5 is ignored. In Shift Left mode, the channel select A/B is
taken from AD5 and the state of AD0 is ignored. AD7 and AD6 are always ignored as
address bits and the register address itself occupies AD4–AD1.
Initializing
The software first issues a series of commands to initialize the basic mode of operation.
These commands are followed by other commands to qualify conditions within the
selected mode. For example, in the ASYNCHRONOUS mode, character length, clock
rate, number of stop bits, and even and odd parity is set first. Next, the INTERRUPT mode
is set. Finally, the receiver and transmitter are enabled.
Write Registers
The ESCC contains 16 write registers (17 counting the transmit buffer) in each channel.
These write registers are programmed to configure the function of the channel. There are
two registers (WR2 and WR9) shared by the two channels, which can be accessed through
either of them. WR2 contains the interrupt vector for both channels. WR9 contains the
interrupt control bits and reset commands. Register WR7’ can be written to if WR15 bit 0
is 1.
Z80X20 Register Access
The Z80230 registers are addressed using the address on AD7–AD0 which are latched by
the rising edge of AS. The Shift Right/Shift Left bit in the Channel B WR0 controls which
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
33
bits are decoded to form the register address. This bit is placed in this register to simplify
programming when the current state of the Shift right/Shift Left bit is not known.
A hardware reset forces SHIFT LEFT mode where the address is decoded from
AD5–AD0. In SHIFT RIGHT mode, the address is decoded from AD4–AD0. The Shift
Right/Shift Left bit is written using a command to make the software writing to WR0 inde-
pendent of the state of the Shift Right/Shift Left bit.
While in the SHIFT LEFT mode, the register address is placed on AD4–AD0 and the
Channel Select bit A/B, is decoded from AD5. In SHIFT RIGHT mode, the register
address is again placed on AD4–AD1 but the Channel Select A/B is decoded from AD0.
Since Z80230 does not contain 16 read registers, the decoding of the read registers is not
complete; this state is listed in Table 4 on page 23 and Table 5 by parentheses around the
register name. These addresses may also be used to access the read registers. The Z80230
contains only one WR2 and WR9; these registers may be written from either channel.
SHIFT LEFT mode is used when Channel A and B are programmed differently. Using
SHIFT LEFT mode allows the software to sequence through the registers of one channel
at a time. The SHIFT RIGHT mode is used when the channels are programmed the same.
By incrementing the address, you can program the same data value into both Channel A
and Channel B registers.
Table 5 lists details of the Z80X30 Register Map in SHIFT LEFT Mode.
Table 5. Z80230 Register Map (Shift Left Mode)
80230
80230
80230
WR15 D2=1
AD5
AD4
AD3
AD2
AD1
Write
WR15 D2=0 WR15 D2=1 WR7’ D6=1
WR08
WR1B
WR2
RR0B
RR1B
RR2B
RR3B
RR0B
RR1B
RR2B
RR3B
RR08
RR1B
RR2B
RR3B
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
WR3B
1
1
1
1
WR4B
WR5B
WR6B
WR7B
(RR0B)
(RR1B)
RR6B
(RR0B)
(RR1B)
(RR2B)
(RR3B)
(WR4B)
(WR5B)
RR6B
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
RR7B
RR7B
1
1
1
1
WR8B
WR9
WR10B
WR11B
RR8B
(RR13B)
RR10B
RR8B
(RR13B)
RR10B
RR8B
(WR3B)
RR10B
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
(RR15B)
(RR15B)
(WR10B)
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
34
Table 5. Z80230 Register Map (Shift Left Mode) (Continued)
80230
80230
80230
WR15 D2=1
AD5
AD4
AD3
AD2
AD1
Write
WR15 D2=0 WR15 D2=1 WR7’ D6=1
1
1
1
1
1
1
1
1
WR12B
WR13B
WR14B
WR15B
RR12B
RR13B
RR14B
RR15B
RR12B
RR13B
RR14B
RR15B
RR12B
RR13B
(WR7’B)
RR15B
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
WR0A
WR1A
WR2
RR0A
RR1A
RR2A
RR3A
RR0A
RR1A
RR2A
RR3A
RR0A
RR1A
RR2A
RR3A
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
WR3A
1
1
1
1
1
1
1
1
WR4A
WR5A
WR6A
WR7A
(RR0A)
(RR1A)
(RR2A)
(RR3A)
(RR0A)
(RR1A)
RR6A
(WR4A)
(WR5A)
RR6A
0
0
0
0
0
0
1
1
0
1
0
1
RR7A
RR7A
1
1
1
1
1
1
1
1
WR8A
WR9
WR10A
WR11A
RR8A
(RR13A)
RR10A
RR8A
(RR13A)
RR10A
RR8A
(WR3A)
RR10A
0
0
0
0
0
0
1
1
0
1
0
1
(RR15A)
(RR15A)
(WR10A)
1
1
1
1
1
1
1
1
1
1
1
1
WR12A
WR13A
WR14A
WR15A
RR12A
RR13A
RR14A
RR15A
RR12A
RR13A
RR14A
RR15A
RR12A
RR13A
(WR7’A)
RR15A
0
0
1
1
0
1
0
1
Notes:
1. The register names in ( ) are the values read out from that register location.
2. WR15 bit D2 enables status FIFO function (not available on NMOS).
3. WR7’ bit D6 enables extend read function (only on ESCC).
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
35
Table 6 lists details of the Z80X30 Register Map in SHIFT RIGHT mode.
Table 6. Z80X30 Register Map (Shift Right Mode)
80230
80230
80230
WR15 D2=1
AD4
AD3
AD2
AD1
AD0
Write
WR15 D2=0 WR15 D2=1 WR7’ D6=1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
WR08
WR0A
WR1B
WR1A
RR0B
RR0A
RR1B
RR1A
RR0B
RR0A
RR1B
RR1A
RR0B
RR0A
RR1B
RR1A
1
1
1
1
WR2
WR2
WR3B
WR3A
RR2B
RR2A
RR3B
RR3A
RR2B
RR2A
RR3B
RR3A
RR2B
RR2A
RR3B
RR3A
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
WR4B
WR4A
WR5B
WR5A
(RR0B)
(RR0A)
(RR1B)
(RR1A)
(RR0B)
(RR0A)
(RR1B)
(RR1A))
(WR4B)
(WR4A)
(WR5B)
(WR5A)
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
1
1
1
1
WR6B
WR6A
WR7B
WR7A
(RR2B)
(RR2A)
(RR3B)
(RR3A)
RR12B
RR13B
RR14B
RR15B
RR12B
RR13B
(WR7’B)
RR15B
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
WR8B
WR8A
WR9
RR8B
RR8A
(RR13B)
(RR13A)
RR8B
RR8A
(RR13B)
(RR13A)
RR8B
RR8A
(WR3B)
(WR3A)
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
WR9
1
1
1
1
1
1
1
1
WR10B
WR10A
WR11B
WR11A
RR10B
RR10A
(RR15B)
(RR15A)
RR10B
RR10A
(RR15B)
(RR15A)
RR10B
RR10A
(WR10B)
(WR10A)
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
1
1
1
1
WR12B
WR12A
WR13B
WR13A
RR12B
RR12B
RR13B
RR13A
RR12B
RR12B
RR13B
RR13A
RR12B
RR12B
RR13B
RR13A
0
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
WR14B
WR14A
WR15B
WR15A
RR12B
RR12B
RR13B
RR13A
RR12B
RR12B
RR13B
RR13A
(WR7’B)
(WR7’B)
RR13B
RR13A
0
0
1
1
0
1
0
1
Notes:
1. The register names in ( ) are the values read out from that register location.
2. WR15 bit D2 enables status FIFO function (not available on NMOS).
3. WR7’ bit D6 enables extend read function (only on ESCC).
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
36
Bits 2–0 of WR0 select registers 0–7. With the Point High command, Registers 8–15 are
selected. Table 7 lists details of the Z8530 Register Map.
Table 7. Z85230/L Register Map
85230
WR15 D2=1
WR7’ D6=1
85230
WR15 D2=0
85230
WR15 D2=1
A/B
PNT2
PNT1
PNT0
Write
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
WR0B
WR1B
WR2
RR0B
RR1B
RR2B
RR3B
RR0B
RR1B
RR2B
RR3B
RR0B
RR1B
RR2B
RR3B
WR3B
1
1
1
1
WR4B
WR5B
WR6B
WR7A
(RR0B)
(RR1B)
(RR2B)
(RR3B)
(RR0B)
(RR1B)
RR6B
(WR4B)
(WR5B)
RR6B
0
0
0
0
0
0
0
0
0
0
1
1
RR7B
RR7B
1
1
1
1
WR0A
WR1A
WR2
RR0A
RR1A
RR2A
RR3A
RR0A
RR1A
RR2A
RR3A
RR0A
RR1A
RR2A
RR3A
1
1
1
1
0
0
0
0
0
0
1
1
WR3A
1
1
1
1
1
1
1
1
WR4A
WR5A
WR6A
WR7A
(RR0A)
(RR1A)
(RR2A)
(RR3A)
(RR0A)
(RR1A)
RR6A
(WR4A)
(WR5A)
RR6A
1
1
1
1
0
0
1
1
RR7A
RR7A
With Point High Command
0
0
0
0
WR8B
WR9
WR10B
WR11B
RR8B
(RR13B)
RR10B
RR8B
(RR13B)
RR10B
RR8B
(WR3B)
RR10B
0
0
0
0
0
0
0
0
0
0
1
1
(RR15B)
(RR15B)
(WR10B)
0
0
0
0
1
1
1
1
WR12B
WR13B
WR14B
WR15B
RR12B
RR13B
RR14B
RR15B
RR12B
RR13B
RR14B
RR15B
RR12B
RR13B
(WR7’B)
RR15B
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
WR8A
WR9
WR10A
WR11A
RR8A
(RR13A)
RR10A
RR8A
(RR13A)
RR10A
RR8A
(WR3A)
RR10A
0
0
0
0
0
0
1
1
(RR15A)
(RR15A)
(WR10A)
1
1
1
1
1
1
1
1
1
1
1
1
WR12A
WR13A
WR14A
WR15A
RR12A
RR13A
RR14A
RR15A
RR12A
RR13A
RR14A
RR15A
RR12A
RR13A
(WR7’A)
RR15A
0
0
1
1
0
0
0
0
WR0B
WR1B
WR2
RR0B
RR1B
RR2B
RR3B
RR0B
RR1B
RR2B
RR3B
RR0B
RR1B
RR2B
RR3B
0
0
0
0
0
0
0
0
0
0
1
1
WR3B
Notes:
1. The register names in ( ) are the values read out from that register location.
2. WR15 bit D2 enables status FIFO function (not available on NMOS).
3. WR7’ bit D6 enables extend read function (only on ESCC).
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
37
Table 8 through Table 24 on page 53 list the format of each write register.
Table 8. Write Register 0
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
0
0
0
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
W
00
01
10
11
Null Code
Reset Tx CRC Checker
Reset Tx CRC Generator
Reset Tx Underrun/EOM Latch
5, 4, 3
000
001
010
011
100
101
110
111
Null Code
Point High
Reset Ext/Status Interrupts
Send Abort (SDLC)
Enable Int on Next Rx Character
Reset Tx Int Pending
Error Reset
Reset Highest IUS
2, 1, 0
000
001
010
011
100
101
110
111
000
001
010
011
100
101
110
111
Register 0
Register 1
Register 2
Register 3
Register 4
Register 5
Register 6
Register 7
Register 8 (with Point High)
Register 9 (with Point High)
Register 10 (with Point High)
Register 11 (with Point High)
Register 12 (with Point High)
Register 13 (with Point High)
Register 14 (with Point High)
Register 15 (with Point High)
For the 80230, bits 1 and 0 are accessible only through Channel B.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
38
Table 9. Write Register 1
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
0
0
X
0
0
X
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
WAIT/DMA Request Enable
Disabled
Enabled
0
1
6
WAIT/DMA Request Function
0
1
Wait
Request
5
WAIT/DMA Request on Receive/Transmit
0
1
Transmit
Receive
4, 3
00
01
10
11
Receive Interrupt Disable
Rec Int on First Character or Special Condition
Int on all Rx Characters or Special Condition
Rx Int on Special Condition Only
2
1
0
Parity is Special condition
Tx Int Enable
Ext Int Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
39
Table 10. Write Register 2
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
V7–Interrupt Vector
V6–Interrupt Vector
V5–Interrupt Vector
V4–Interrupt Vector
V3–Interrupt Vector
V2–Interrupt Vector
V1–Interrupt Vector
V0–Interrupt Vector
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
40
Table 11. Write Register 3
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
00
01
10
11
Rx 5 Bits/Character
Rx 7 Bits/Character
Rx 6 Bits/Character
Rx 8 bits/Character
5
4
3
2
1
0
Auto Enable
Enter HUNT Mode
Rx CRC Enable
Address Search Mode (SDLC)
Sync Character Load Inhibit
Rx Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
41
Table 12. Write Register 4
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
1
X
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
00
01
10
11
X1 Clock Mode
X16 Clock Mode
Z32 Clock Mode
X64 Clock Mode
5, 4
3, 2
00
01
10
11
8-Bit Sync Character
16-Bit Sync Character
SDLC Mode (01111110 Flag)
External Sync Mode
00
01
10
11
Sync Modes Enable
1 Stop Bit/Character
1.5 Stop Bits/Character
2 Stop Bits/Character
1
0
Parity EVEN/ODD
Odd
Even
0
1
Parity Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
42
Table 13. Write Register 5
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
0
X
X
0
0
0
0
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
DTR
6, 5
00
01
10
11
Tx 5 Bits (or less)/Character
Tx 7 Bits/Character
Tx 6 Bits/Character
Tx 8 Bits/Character
4
3
2
Send Break
Tx Enable
CRC-16/CRC-CCITT
CRC-CCITT
CRC-16
0
1
1
0
RTS
Tx CRC Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
43
Table 14. Write Register 6
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Description
SDLC
(Address
Range)
Monos
ync 6
Bits
Bit
Bisync
16 Bits
Bisync
12 Bits
Monosync 8
Bits
Position R/W
Value
SDLC
7
6
5
4
3
2
1
0
Sync7
Sync6
Sync5
Sync4
Sync3
Sync2
Sync1
Sync0
Sync1
Sync0
Sync5
Sync4
Sync3
Sync2
Sync1
Sync0
Sync7
Sync6
Sync5
Sync4
Sync3
Sync2
Sync1
Sync0
Sync3
ADR7
ADR6
ADR5
ADR4
ADR3
ADR2
ADR1
ADR0
ADR7
ADR6
ADR5
ADR4
X
Sync2
Sync1
Sync0
1
1
1
1
X
X
X
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
44
Table 15. Write Register 7
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Description
Bit
Position
R/W
Value
This
Bisync 16
Bits
Bisync
12 Bits
Monosync 8 Monosync 6
column
contains
no data
SDLC
Bits
Bits
7
6
5
4
3
2
1
0
Sync7
Sync6
Sync5
Sync4
Sync3
Sync2
Sync1
Sync0
Sync5
Sync4
Sync3
Sync2
Sync1
Sync0
X
Sync15
Sync14
Sync13
Sync12
Sync11
Sync10
Sync9
Sync11
Sync10
Sync9
Sync8
Sync7
Sync6
Sync5
Sync4
0
1
1
1
1
1
1
0
X
Sync8
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
45
Table 16. Write Register 7’
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
0
0
1
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
0
Not Used. Must be 0.
Extended Read Enable
Tx FIFO Int Level
DTR/REQ Timing Mode
Rx FIFO Int Level
Auto RTS Deactivation
Auto EOM Reset
Auto Tx Flag
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
46
Table 17. Write Register 8
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
0
0
1
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
47
Table 18. Write Register 9
Bit
7
6
5
4
3
2
1
0
W
R/W
1
1
0
0
0
0
0
X
X
X
X
Hardware
Reset
X
X
X
X
X
Channel Reset
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
00
01
10
11
No Reset
Channel Reset B
Channel Reset A
Force Hardware Reset
5
4
Software INTACK Enable
Status High/ Status Low
0
1
Low
High
3
2
1
0
Master Interrupt Enable
Disable Lower Chain
No Vector
Vector Includes Status
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
48
Table 19. Write Register 10
Bit
7
6
5
4
3
2
1
0
W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Hardware
Reset
X
X
Channel Reset
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
CRC Preset I/O
6, 5
00
01
10
11
NRZ
NRZI
FM 1 (Transition = 1)
FM 0 (Transition = 0)
4
3
Go Active on Poll
Mark/Flag Idle
Flag Idle
Mark Idle
0
1
2
Abort/Flag on Underrun
0
1
Flag
Abort
1
0
Loop Mode
6-Bit/8-Bit sync
8-Bit
6-bit
0
1
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
49
Table 20. Write Register 11
Bit
7
6
5
4
3
2
1
0
W
R/W
0
0
0
0
1
0
0
0
Hardware
Reset
X
X
X
X
X
X
X
X
Channel Reset
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
RTxC Xtal/No Xtal
No Xtal
RTxC Xtal
0
1
6, 5
4, 3
00
01
10
11
Receive Clock = RTxC Pin
Receive Clock = TRxC Pin
Receive Clock = BRG Output
Receive Clock = DPLL Output
00
01
10
11
Transmit Clock = RTxC Pin
Transmit Clock = TRxC Pin
Transmit Clock = BRG Output
Transmit Clock = DPLL Output
2
1
TRxC Input/Output
Output
Input
0
1
00
01
10
11
TRxC Out = Xtal Output
TRxC Out = Transmit Clock
TRxC Out = BRG Output
TRxC Out = DPLL Output
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
50
Table 21. Write Register 12
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Lower Byte of Time Constant)
7
6
5
4
3
2
1
0
TC7
TC6
TC5
TC4
TC3
TC2
TC1
TC0
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
51
Table 22. Write Register 13
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Upper Byte of Time Constant)
7
6
5
4
3
2
1
0
TC15
TC14
TC13
TC12
TC11
TC10
TC9
TC8
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
52
Table 23. Write Register 14
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Upper Byte of Time Constant)
7, 6, 5
000
001
010
011
100
101
110
111
Null Command
Enter Search Mode
Reset Missing Clock
Disable DPLL
Set source - BRG
Set Source = RTxC
Set FM Mode
Set NRZI Mode
4
3
2
1
0
Local Loopback
Auto Echo
DTR/Request Generator Source
BRG Source
BRG Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
53
Table 24. Write Register 15
Bit
7
6
5
4
3
2
1
0
W
R/W
Reset
1
1
1
1
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
Break/Abort Interrupt Enable
Tx Underrun/EOM Interrupt Enable
CTS Interrupt Enable
Sync/Hunt
DCD Interrupt Enable
SDLC FIFO Enable
Zero Count Interrupt Enable
WR7’ SDLC Feature Enable
Read Registers
The ESCC contains ten read registers (eleven, counting the receive buffer RR8) in each
channel. Four of these may be read to obtain status information (RR0, RR1, RR10, and
RR15).
Two registers, RR12 and RR13, are read to learn the BRG time constant. RR2 contains
either the unmodified interrupt vector, Channel A, or the vector modified by status infor-
mation, Channel B.
RR3 contains the Interrupt Pending (IP) bits for Channel A.
RR6 and RR7 contain the information in the SDLC Frame Status FIFO, but is only read
when WR15 bit 2 is 1. If WR7’ bit 6 is 1, Write Registers WR3, WR4, WR5, and WR10
can be read as RR9, RR4, RR5, and RR14, respectively. Table 25 on page 54 through
Table 40 on page 69 list the format of the read registers.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
54
Table 25. Read Register 0
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
1
X
X
X
1
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
Break/Abort
Tx Underrun/EOM
CTS
Sync/Hunt
DCD Interrupt Enable
Tx Buffer Empty
Zero Count
Rx Character Available
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
55
Table 26. Read Register 1
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
0
0
0
0
0
1
1
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
EOF (SDLC)
CRC/Framing Error
Rx Overrun Error
Parity Error
Residue Code 0
Residue Code 1
Residue Code 2
All Sent
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
56
Table 27. Read Register 2
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Interrupt Vector)
7
6
5
4
3
2
1
0
V7
V6
V5
V4
V3
V2
V1
V0
These bits include status information when read from Channel B.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
57
Table 28. Read Register 3
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
0
0
Channel A Rx IP
Channel A Tx IP
Channel A Ext/Status IP
Channel B Rx IP
Channel B Tx IP
Channel B Ext/Status IP
Bits 5, 4, 3, 2, 1 and 0 are always 0 when read from Channel B.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
58
Table 29. Read Register 4
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
00
01
10
11
X1 Clock Mode
X16 Clock Mode
Z32 Clock Mode
X64 Clock Mode
5, 4
3, 2
00
01
10
11
8-Bit Sync Character
16-Bit Sync Character
SDLC Mode (01111110 Flag)
External Sync Mode
00
01
10
11
Sync Modes Enable
1 Stop Bit/Character
1.5 Stop Bits/Character
2 Stop Bits/Character
1
0
Parity EVEN/ODD
Odd
Even
0
1
Parity Enable
This register reflects the contents of RR0 if WR7’ bit 6 is enabled.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
59
Table 30. Read Register 5
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
DTR
6, 5
00
01
10
11
Tx 5 Bits (or less)/Character
Tx 7 Bits/Character
Tx 6 Bits/Character
Tx 8 Bits/Character
4
3
2
Send Break
Tx Enable
CRC-16/CRC-CCITT
CRC-CCITT
CRC-16
0
1
1
0
RTS
Tx CRC Enable
This register reflects the contents of RR1 if WR7’ bit 6 is enabled.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
60
Table 31. Read Register 6
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
BC7
BC6
BC5
BC4
BC3
BC2
BC1
BC0
This register can be accessed only if WR15 bit 2 is 1. If this bit is not enabled this register reflects
RR2.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
61
Table 32. Read Register 7
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
FOS: FIFO Status Overflow
FIFO Overflowed
Normal
0
1
6
FDA: FIFO Data Available
Status Reads from FIFO
Status Reads from ESCC
0
1
5
4
3
2
1
0
BC13
BC12
BC11
BC10
BC9
BC8
This register can be accessed only if WR15 bit 2 is 1. If this bit is not enabled this register reflects
RR3.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
62
Table 33. Read Register 8
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
0
0
1
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
63
Table 34. Read Register 9
Bit
7
6
5
4
3
2
1
0
R
R/W
1
1
0
0
0
0
0
X
X
X
X
Hardware Reset
Channel Reset
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7, 6
00
01
10
11
No Reset
Channel Reset B
Channel Reset A
Force Hardware Reset
5
4
Software INTACK Enable
Status High/Status Low
0
1
Low
High
3
2
1
0
Master Interrupt Enable
Disable Lower Chain
No Vector
Vector Includes Status
To access this register WR7’ bit 6 must be enabled.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
64
Table 35. Read Register 10
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
0
0
1
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
One Clock Missing
Two Clocks Missing
0
Loop Sending
0
0
On Loop
0
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
65
Table 36. Read Register 11
Bit
7
6
5
4
3
2
1
0
R
R/W
0
0
0
0
0
0
0
0
Hardware Reset
Channel Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
CRC Preset I/O
6, 5
00
01
10
11
NRZ
NRZI
FM1 (Transition = 1)
FM0 (Transition = 0)
4
3
Go Active on Poll
Mark/Flag Idle
Flag Idle
Mark Idle
0
1
2
Abort Flag on Underrun
0
1
Flag
Abort
1
0
Loop Mode
6-Bit/8-Bit Sync
8-Bit Sync
6-Bit Sync
0
1
To access this register WR7’ bit 6 must be enabled. If this bit is not enabled, this register reflects
RR15.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
66
Table 37. Read Register 12
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Lower Byte of Time Constant)
7
6
5
4
3
2
1
0
TC7
TC6
TC5
TC4
TC3
TC2
TC1
TC0
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
67
Table 38. Read Register 13
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description (Upper Byte of Time Constant)
7
6
5
4
3
2
1
0
TC15
TC14
TC13
TC12
TC11
TC10
TC9
TC8
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
68
Table 39. Read Register 14
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
0
0
1
0
0
0
0
0
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
0
Not Used. Must be 0.
Extended Read Enable
Tx FIFO Int Level
DTR/REQ Timing Mode
Rx FIFO Int Level
Auto RTS Deactivation
Auto EOM Reset
Auto Tx Flag
To access this register WR7’ bit 6 must be enabled. If this bit is not enabled this register reflects
RR10.
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
69
Table 40. Read Register 15
Bit
7
6
5
4
3
2
1
0
R
R/W
Reset
X
X
X
X
X
X
X
X
R = Read W = Write X = Indeterminate
Bit
Position
R/W
Value
Description
7
6
5
4
3
2
1
0
Break/Abort Interrupt Enable
Tx Underrun/EOM Interrupt Enable
CTS Interrupt Enable
Sync/Hunt
DCD Interrupt Enable
SDLC FIFO Enable
Zero Count Interrupt Enable
WR7’ SDLC Feature Enable
PS005308-0609
Programming
Z80230/Z85230/L
Product Specification
70
Z80230 Interface Timing
Z80230 Write Cycle Timing
The Z-Bus compatible ESCC is suited for system applications with multiplexed address/
data buses.
Two control signals, AS and DS, are used by the Z80230 to control bus transactions. Addi-
tionally, four other control signals (CS0, CS1, RW, and INTACK) control the type of bus
transaction that occurs. A bus transaction is initiated by AS. The rising edge latches the
register address on the Address/Data bus and the state of INTACK and CS0.
In addition to bus transactions, the interrupt section uses the AS to set Interrupt Pending
(IP) bits. Therefore, AS must be kept cycling for the interrupt section to function.
The Z80230 generates internal control signals in response to a register access. Because AS
and DS have no defined phase relationship with PCLK, the circuitry generating these
internal control signals provide time for metastable conditions to disappear. This action
results in a recovery time related to PCLK.
This recovery time applies only to transactions involving the Z80230, and any intervening
transactions are ignored. This recovery time is four PCLK cycles, measured from the fall-
ing edge of DS for one access to the ESCC, to the falling edge of DS for a subsequent
access. Figure 17 displays the Write cycle timing.
AS
CS0
INTACK
Data Valid
A7–A0
R/W
CS1
DS
Address
Figure 17. Z80230 Write Cycle Timing
PS005308-0609
Z80230 Interface Timing
Z80230/Z85230/L
Product Specification
71
Z80230 Read Cycle Timing
The Read Cycle Timing for the Z80230 is displayed in Figure 18. The register address on
A7-A0, as well as the state of CS0 and INTACK, are latched by the rising edge of AS.
R/W must be High before DS falls to indicate a Read cycle. The Z80230 data bus drivers
are enabled while CS1 is High and DS is Low.
AS
CS0
INTACK
Data Valid
Address
A7–A0
R/W
CS1
DS
Figure 18. Z80230 Read Cycle Timing
Z80230 Interrupt Acknowledge Cycle Timing
The Interrupt Acknowledge cycle timing for the Z80230 is displayed in Figure 19 on page
72. The address on A7-A0 and the state of CS0 and INTACK are latched by the rising -
edge of AS. However, if INTACK is Low. The address on A7-A0, CS0, CS1, and R/W
are ignored for the duration of the interrupt acknowledge cycle.
The Z80230 samples the state of INTACK on the rising edge of AS, and AC parameters.
Parameters 7 and 8 of Table 45 on page 83, specify the setup and hold time requirements.
Between the rising edge of AS and the falling edge of DS, the internal and external daisy
chains settle, as specified in parameter 29. A system with no external daisy chain provides
the time priority internal to the ESCC. Systems using an external daisy chain must refer to
Note 5 of Table 45, for the time required to settle the daisy chain.
If there is an interrupt pending in the ESCC, and IEI is High when DS falls, the acknowl-
edge cycle is intended for the ESCC. Consequently, the Z80230 sets the Interrupt Under
Service (IUS) latch for the highest priority pending interrupt, and places an interrupt vec-
PS005308-0609
Z80230 Interface Timing
Z80230/Z85230/L
Product Specification
72
tor on A7-A0. WR9 bit 1 is set to 1 to disable the placing of a vector on a bus. The INT pin
also goes inactive in response to the falling edge of DS. There is only one DS per interrupt
acknowledge cycle.
IP bits in the Z80230 are updated by AS, which can delay interrupt requests if the proces-
sor does not supply AS strobes during the time in between accesses of the Z80230.
AS
CS0
A7–A0
DS
Vector
INTACK
IEI
IEO
INT
Figure 19. Z80230 Interrupt Acknowledge Cycle Timing
Z85230/L Timing
The ESCC generates internal control signals from WR and RD that relate to PCLK.
Because PCLK had no defined phase relationship with WR and RD, the circuitry generat-
ing the internal control signals provides time for metastable conditions to disappear. This
causes a recovery time related to PCLK. The recovery time applies only to bus transac-
tions involving the ESCC. The recovery time required for proper operation is specified
PS005308-0609
Z80230 Interface Timing
Z80230/Z85230/L
Product Specification
73
from the falling edge of WR or RD in the first transaction involving the ESCC, to the fall-
ing edge of WR or RD in the second transaction. This time must be at least four PCLKs
regardless of which register or channel is accessed.
Z85230/L Read Cycle Timing
Figure 20 displays Read Cycle timing. Addresses on A/B and D/C and the status on
INTACK must remain stable throughout the cycle. The effective RD time reduces if CE
falls after RD falls, or if it rises before RD rises.
A/B, D/C
INTACK
CE
Address Valid
D7–D0
RD
Data Valid
Figure 20. Read Cycle Timing (Z85230/L)
Z85230/L Write Cycle Timing
Figure 21 on page 74 displays Write Cycle timing. Addresses on A/B and D/C and the sta-
tus on INTACK must remain stable throughout the cycle. The effective WR time reduces
if CE falls after WR falls, or if it rises before WR rises. In Write Cycle timing, the WR sig-
nal returns a High slightly before the Address goes invalid.
Because many popular CPUs do not guarantee that the databus is valid when WR is Low,
the ESCC no longer requires a valid databus when the WR pin is Low. For more informa-
tion, see AC characteristics parameter 29 available in Table 47 on page 90.
PS005308-0609
Z80230 Interface Timing
Z80230/Z85230/L
Product Specification
74
A/B, D/C
INTACK
CE
Address Valid
Address Valid
D7–D0
WR
Figure 21. Write Cycle Timing (Z85230/L)
Z85230/L Interrupt Acknowledge Cycle Timing
Figure 22 displays Interrupt Acknowledge Cycle timing. Between the time INTACK goes
Low and the falling edge of RD, the internal and external IEI/IEO daisy chains settle. If
there is an interrupt pending in the ESCC and IEI is High when RD falls, the Acknowl-
edge cycle is intended for the ESCC. In this case, the ESCC may be programmed to
respond to RD Low by placing its interrupt vector on D7–D0. It then sets the appropriate
IUS latch internally. If the external daisy chain is not used, then AC Parameter 38 is
required to settle the interrupt priority daisy chain internal to the ESCC. If the external
daisy chain is used, follow the equation in AC Characteristics Note 5 (Table 47 on
page 90) to calculate the required daisy chain settle time.
INTACK
RD
D7–D0
Vector
Figure 22. Interrupt Acknowledge Cycle Timing (Z85230/L)
PS005308-0609
Z80230 Interface Timing
Z80230/Z85230/L
Product Specification
75
Electrical Characteristics
Absolute Maximum Ratings
Stresses greater than those listed in this section can cause permanent damage to the device.
These ratings are stress ratings only. Operation of the device at any condition above those
indicated in the operational section of this specification is not implied. Exposure to abso-
lute maximum rating conditions for extended periods can affect reliability.
VCC Supply Voltage Range
–0.3 V to +7.0 V
Voltages on All Pins with Respect to
GND
–0.3 V to VCC +0.3 V
Operating Ambient Temperature
See Ordering Information on
page 107
Storage Temperatures
–65º C to +150º C
Standard Test Conditions
The DC Characteristics and capacitance sections apply for the following standard test
conditions, unless otherwise noted. All voltages reference GND. Positive current flows
into the referenced pin. Standard conditions are as follows:
•
•
•
GND = 0 V
T as specified in Ordering Information
+4.5V VCC +5.5V" or +3.0 V VCC +3.6V (Z8523L only)
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
76
Figure 23 displays typical test load configurations.
+VCC
+VCC
2.1K
2.2K
From Output
Under Test
From Output
50pf
100pf
250µA
Open-Drain Test Load
Standard Test Load
Figure 23. Standard and Open-Drain Test Loads
Capacitance
Table 41 lists the capacitance parameters and contains the symbols and test conditions for
each.
Table 41. Capacitance Parameters
Symbol
Parameter
Min
Max
10
Unit
pF
Test Condition
C
C
C
Input Capacitance
Output Capacitance
Bidirectional Capacitance
Unmeasured Pins
Returned to Ground
IN
15
pF
OUT
I/O
20
pF
Note: f = 1 MHz, over specified temperature range.
Miscellaneous
Gate count—11,000 for both Z80230 and Z85230/L.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
77
DC Characteristics
Table 42 lists the DC characteristics for the Z80230/Z85230 device.
Table 42. Z80230/Z85230 DC Characteristics
Symbol
Parameter
Min.
Typ. Max.
+ 0.3
Unit Condition
V
V
V
V
V
Input High Voltage 2.2
V
V
IH
CC
Input Low Voltage
– 0.3
0.8
V
IL
Output High Voltage 2.4
V
IOH = – 1.6 mA
IOH = – 250 A
IOL = +2.0 mA
OH1
OH2
OL
Output High Voltage V – 0.8
V
CC
Output Low Voltage
Input Leakage
0.4
V
I
I
I
± 10.0
± 10.0
µA
µA
0.4 <V <+2.4 V
IN
IL
Output Leakage
0.4 <V
<+2.4 V
OUT
OL
V
Supply Current
4
5
7
9
10 (8.5 MHz)
12 (10 MHz)
15 (16 MHz)
20 (20 MHz)
mA
mA
mA
mA
V
=5 V,V =4.8,
CC IH
CC1
CC
V =0.2 V
Crystal oscillators off
IL
I
Crystal OSC Current
6
mA
Current for each oscillator
CC(OSC)
in addition to I
CC1
Notes:
1. Vcc=5 V ± 10% unless otherwise specified, over specified temperature range.
2. Typical Icc was measured with oscillator off.
3. No Icc(osc) max is specified because of dependency on the external circuit.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
78
Table 43 lists the DC characteristics for the Z8523L device.
Table 43. Z8523L DC Characteristics
Symbol
Parameter
Min.
Typ. Max.
+ 0.3
Unit Condition
V
V
V
V
V
Input High Voltage 2.2
V
V
IH
CC
Input Low Voltage
– 0.3
0.2*V
V
IL
CC
Output High Voltage 2.4
V
IOH = – 1.6 mA
IOH = – 250 A
IOL = +2.0 mA
OH1
OH2
OL
Output High Voltage V – 0.4
V
CC
Output Low Voltage
Input Leakage
0.2
V
I
I
I
± 10.0
± 10.0
µA
µA
0.4 <V <+2.4 V
IN
IL
Output Leakage
0.4 <V
<+2.4 V
OUT
OL
V
Supply Current
2
2.5
4
3 (8.5 MHz)
4 (10 MHz)
6 (16 MHz)
mA
mA
mA
V
=3.3 V,V =3.1,
CC IH
CC1
CC
V =0.2 V
Crystal oscillators off
IL
I
Crystal OSC Current
6
mA
Current for each oscillator
CC(OSC)
in addition to I
CC1
Notes:
1. Vcc=3.3 V ± 10% unless otherwise specified, over specified temperature range.
2. Typical Icc was measured with oscillator off.
3. No Icc(osc) max is specified because of dependency on the external circuit.
4. I/O pins are NOT 5V tolerant
AC Characteristics
Figure 24 on page 79 displays the Z80230 Read/Write timing diagram.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
79
AS
CS0
CS1
2
1
3
4
6
5
14
INTACK
7
8
R/W
Read
9
10
10
W/R
Write
11
DS
12
18
20
23
13
AD7-AD0
Write
16
16
15
15
17
AD7-AD0
Read
19
25
21
22
24
W/REQ
Wait
W/REQ
Request
26
DTR/REQ
Request
27
INT
28
PCLK
41
43
40
44
42
Figure 24. Z80230 Read/Write Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
80
Figure 25 displays the Z80230 Interrupt Acknowledge timing diagram
AS
7
INTACK
8
DS
30
29
20
19
AD7-AD0
Active
Valid
22
33
31
32
IEI
IEO
INT
35
34
36
Figure 25. Z80230 Interrupt Acknowledge Timing Diagram
Figure 26 displays the Z80230 Reset timing diagram
AS
DS
35
38
37
Figure 26. Z80230 Reset Timing Diagram
Table 45 lists the AC characteristics of the Z80230 and Table 47 lists the AC characteris-
tics of Z85230/L.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
81
Figure 27 displays the Z80230 general timing diagram.
PCLK
1
W/REQ
Request
2
W/REQ
Wait
3
CTS/TRxC,
RTxC
Receive
4
6
5
7
RxD
8
9
SYNC
External
10
CTS/TRxC,
RTxC
Transmit
11
12
TxD
13
CTS/TRxC
Output
14
15
RTxC
16
17
CTS/TRxC
18
19
20
CTS/TRxC,
DCD
21
22
21
22
SYNC
Input
Figure 27. Z80230 General Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
82
Table 44 lists the Z80230 general timing characteristics details.
Table 44. Z80230 General Timing Characteristics
10 MHz
Min.
16 MHz
No.
1
Symbol
Parameter
Max.
Min.
Max. Notes
TdPC (REQ)
TsPC (W)
TsRXC (PC)
PCLK Low to W/REQ Valid
PCLK Low to Wait Inactive
200
300
110
9
2
180
9
3
RxC High to PCLK High Setup NA
Time
NA
1, 4, 9
4
TsRXD (RXCr) RxD to RxC High Setup Time
ThRXD (RxCr) RxD to RxC High Hold Time
TsRXD (RXCf) RxD to RxC Low Setup Time
ThRXD (RXCf) RxD to RxC Low Hold Time
0
0
1,9
5
125
0
60
0
1,9
6
1, 5, 9
1, 5, 9
1, 9
7
125
60
8
TsSY (RXC)
ThSY (RXC)
TsTXC (PC)
SYNC to RxC High Setup Time -150
SYNC to RxC High Hold Time
-100
5
9
5
1, 10
2, 4, 9
10
TxC Low to PCLK High Setup NA
Time
NA
11
12
13
14
15
16a
16b
17
18
19
20
21
22
TdTXCf (TXD) TxC Low to TxD Delay
150
150
140
85
85
80
2, 9
2, 5, 9
9
TdTxCr (TXD)
TdTXD (TRX)
TwRTXh
TwRTXI
TxC High to TxD Delay
TxD to TRxC Delay
RTxC High Width
120
120
400
50
80
6, 9
6, 9
6, 7, 9
7, 8, 9
3, 9
6, 9
6, 9
6, 7, 9
9
TRxC Low Width
80
TcRTX
RTxC Cycle Time
244
31
TxRX (DPLL)
TcRTXX
TwTRXh
TwTRXI
DPLL Cycle Time Minimum
Crystal Oscillator Period
TRxC High Width
100
120
120
400
120
120
1000
100
80
1000
TRxC Low Width
80
TcTRX
TRxC Cycle Time
244
70
TwEXT
DCD or CTS Pulse Width
SYNC Pulse Width
TwSY
70
9
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
83
Table 44. Z80230 General Timing Characteristics (Continued)
10 MHz
Min.
16 MHz
No.
Symbol
Parameter
Max.
Min.
Max. Notes
Notes:
1. RxC is RTxC or TRxC, whichever is supplying the receive clock.
2. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
3. Both RTxC and SYNC have 30 pf capacitors to ground connected to them.
4. Synchronization of RxC to PCLK is eliminated in divide by four operation.
5. Parameter applies only to FM encoding/decoding.
6. Parameter applies only for transmitter and receiver; DPLL and BRG timing requirements are identical to PCLK
requirements.
7. The maximum transmit or receive data rate is 1/4 PCLK.
8. Applies to the DPLL clock source only. Maximum data rate of 1/4 PCLK still applies. DPLL clock must have a
50% duty cycle.
9. Units in ns.
10.Units in TcPc.
Table 45 lists the Z80230 Read and Write AC characteristics.
Table 45. Z80230 AC Characteristics
10 MHz
Max.
16 MHz
Max
No
1
Symbol
TwAS
Parameter
Min.
30
10
0
Min.
20
10
0
Notes
8
AS Low Width
2
TdDS (AS)
DS Rise to AS Fall Delay
1, 8
1, 8
1, 8
1, 8
1, 8
8
3
TsCS0 (AS) CS0 to AS Rise Setup Time
ThCS0 (AS) CS0 to AS Rise Hold Time
TsCS1 (DS) CS1 to DS Fall Setup Time
ThCS1 (DS) CS1 to DS Rise Hold Time
4
20
50
20
10
125
50
15
35
10
10
100
35
5
6
7
TsIA (AS)
ThIA (AS)
INTACK to AS Rise Setup Time
INTACK to AS Rise Hold Time
8
8
9
TsRWR
(DS)
R/W (Read) to DS Fall Setup
Time
8
10
11
ThRW (DS) R/W to DS Rise Hold Time
0
0
0
0
8
8
TsRWW
(DS)
R/W (Write) to DS Fall Setup
Time
12
TdAS (DS)
AS Rise to DS Fall Delay
20
15
8
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
84
Table 45. Z80230 AC Characteristics (Continued)
10 MHz
Max.
16 MHz
No
13
14
15
16
17
18
19
20
Symbol
TwDSI
TrC
Parameter
Min.
125
4
Min.
80
4
Max
Notes
DS Low Width
8
Valid Access Recovery Time
Address to AS Rise Setup Time
Address to AS Rise Hold Time
2, 9
1, 8
1, 8
8
TsA (AS)
ThA (AS)
10
10
10
10
0
20
TsDW (DS) Write Data to DS Fall Setup Time 10
ThDW (DS) Write Data to DS Rise Hold Time
TdDS (DA) DS Fall to Data Active Delay
0
0
0
8
0
8
TdDSr (DR) DS Rise to Read Data Not Valid
Delay
0
8
21
22
23
TdDSf (DR) DS Fall to Data Active Delay
120
190
35
70
8
TdAS (DR)
AS Rise to Read Data Valid Delay
110
20
8
TdDS (DRz) DS Rise to Read Data Float
Delay
3, 8
24
TdA (DR)
Address Required Valid to Read
Data Valid Delay
210
100
25
26
TdDS (W)
DS Fall to Wait Valid Delay
160
160
60
60
4, 8
8
TdDSf
(REQ)
DS Fall to W/REQ Not Valid
Delay
27
TdDSr
(REQ)
DS Fall to DTR/REQ Not Valid
Delay
4
4
9
5
28
29
TdAS (INT) AS Rise to INT Valid Delay
500
175
TdAS (DSA) AS Rise to DS Fall
(Acknowledge) Hold Time
225
50
30
31
TsDSA
DS (Acknowledge) Low Width
125
120
75
70
8
8
TdDSA (DR) DS Fall (Acknowledge) to Read
Data Valid Delay
32
33
TsIEI (DSA) IEI to DS Fall (Acknowledge)
Setup time
80
0
50
0
8
8
ThIEI (DSA) IEI to DS Rise (Acknowledge)
Hold Time
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
85
Table 45. Z80230 AC Characteristics (Continued)
10 MHz
16 MHz
No
34
35
36
Symbol
Parameter
Min.
Max.
90
Min.
Max
45
Notes
TdIEI (IEO) IEI to IEO Delay
8
TdAS (IEO) AS Rise to IEO Delay
175
450
80
6
TdDSA (INT) DS Fall (Acknowledge) to INT
Inactive Delay
200
4, 8
37
38
39
TdDS (ASQ) DS Rise to AS Fall Delay for No 15
Reset
10
10
75
8
8
8
TdASQ (DS) AS Rise to DS Fall Delay for No 15
Reset
TwRES
AS and DS Coincident Low for
Reset7
100
40
TwPCl
TwPCh
TcPc
PCLK Low Width
PCLK High Width
PCLK Cycle Time
PCLK Rise Time
PCLK Fall Time
40
100
1000
2000
10
26
26
61
1000
1000
2000
5
8
8
8
8
8
41
40
42
100
43
TrPC
44
TfPC
10
5
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Parameter applies only between transactions involving the ESCC.
3. Float delay is defined as the time required for a ±0.5 V change in the output with a maximum DC load and a min-
imum AC load.
4. Open-drain output, measured with open-drain test load.
5. Parameter is system-dependent. For any Zilog ESCC in the daisy chain. TdAS (DSA) must be greater than the
sum of TdAS (IEO) for the highest priority device in the daisy chain. TsIEI (DSA) for the Zilog ESCC, and TdIEI
(IEO) for each device separating them in the daisy chain.
6. Parameter applies only to a Zilog ESCC pulling INT Low at the beginning of the Interrupt Acknowledge transac-
tion.
®
7. Internal circuitry allows for the reset provided by the Z8 to be recognized as a reset by the Z-ESCC. All timing
references assume 2.0 V for a 1 and 0.8 V for a logic 0.
8. Units in ns.
9. Units inTcPc
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
86
Figure 28 displays the Z80230 system timing diagram.
RTxC,TRxC
Receive
W/REQ
Request
1
W/REQ
Wait
2
SYNC
Output
3
INT
4
TRxC,RTxC
Transmit
W/REQ
Request
5
W/REQ
Wait
6
DTR/REQ
Request
7
INT
8
CTS,DCD
SYNC
Input
9
INT
10
Figure 28. Z80230 System Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
87
Table 46 lists the Z80230 system timing parameter details.
Table 46. Z80230 System Timing Table
10 MHz
Max.
16 MHz
No.
1
Symbol
Parameter
Min.
13
13
9
Min.
13
13
9
Max.
17
Notes
2, 5
TdRXC (REQ) RxC High to W/REQ Valid
17
19
12
2
TdRXC (W)
TdRXC (SY)
RxC High to Wait Inactive
RxC High to SYNC Valid
19
1, 2, 5
2, 5
3
12
4
TdRXC (INT), RxC High to INT Valid
Z80230
13
2
17
3
13
2
17
3
1, 2, 4
5
6
7
8
TdTXC (REQ) TxC Low to W/REQ Valid
11
8
14
14
11
8
14
14
3, 5
TdTXC (W)
TxC Low to Wait Inactive
1, 3, 5
3, 5
TdTXC (DRQ) TxC Low to DTR/REQ Valid
TdTXC (INT), TxC Low to INT Valid
Z80230
7
2
9
3
7
2
9
3
1, 3, 4
9
TdSY (INT)
SYNC to INT Valid
2
+2
6
+3
2
+2
6
+3
1, 5
1, 4
10
TdEXT (INT), DCD or CTS to INT Valid
Z80230
2
3
3
8
Notes:
1. Open-drain output, measured with open-drain test load.
2. RxC is RTxC or TRxC, whichever is supplying the receive clock.
3. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
4. Units equal to AS.
5. Units equal to TcPc.
Z85230/L AC Characteristics
Figure 29 on page 88 displays the Z85230/L Read and Write Timing Diagram. Figure 30
on page 89 displays the Z85230/L Reset Timing Diagram. Figure 31 on page 89 displays
the Z85230/L Interrupt Acknowledge Timing Diagram. Figure 32 on page 89 displays the
Z85230/L Cycle Timing Diagram.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
88
1
PCLK
2
4
3
6
5
A/B, D/C
7
10
9
8
INTACK
CE
12
11
16
13
10
14
15
18
RD
19
20
21
22
D7–D0
Read
Active
Valid
24
23
26
17
25
27
WR
28
D7–D0
Write
29
31
30
W/REQ
Wait
32
35
W/REQ
Request
33
DTR/REQ
Request
34
36
INT
37
Figure 29. Z85230/L Read/Write Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
89
WR
RD
46
47
48
Figure 30. Z85230/L Reset Timing Diagram
PCLK
15
10
INTACK
RD
10
38
14
24
39
23
Active
40
Valid
D 7–D0
IEI
26
42
41
44
43
IEO
45
INT
Figure 31. Z85230/L Interrupt Acknowledge Timing Diagram
CE
49
RD or WR
Figure 32. Z85230/L Cycle Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
90
Table 47 lists the Z85230/L Read and Write AC characteristics details.
Table 47. Z85230/L AC Characteristics (20MHz applies only to Z85230)
8.5 MHz
10 MHz
16 MHz
20 MHz
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
1
2
3
4
5
6
TwPCl
TxPCh
TfPC
TrPC
TcPc
TsA
PCLK Low Width 45
PCLK High Width 45
PCLK Fall Time
1000 40
1000 40
10
1000 26
1000 26
10
1000 22
1000
1000
5
6
6
6
6
6
6
1000 22
5
PCLK Rise Time
10
10
5
5
PCLK Cycle Time 118 2000 100 2000 61
2000 50
30
2000
Address to WR fall 66
Setup Time
50
35
7
ThA (WR)
TsA (RD)
ThA (RD)
TsIA (PC)
TsIAi (WR)
ThIA (WR)
TsIAi (RD)
ThIA (RD)
ThIA (PC)
Address to WR
Rise Hold Time
0
0
0
0
6
8
Address to RD Fall 66
Setup Time
50
0
35
0
30
0
6
9
Address to RD
Rise Hold Time
0
6
10
11
12
13
14
15
16
17
INTACK to PCLK 20
Rise Setup Time
20
130
0
15
70
0
15
65
0
6
INTACK to WR
Fall Setup Time
140
1, 6
6
INTACK to WR
Rise Hold Time
0
INTACK to RD Fall 140
Setup Time
130
0
70
0
65
0
1, 6
6
INTACK to RD
Rise Hold Time
0
INTACK to PCLK 38
Rise Hold Time
30
0
15
0
15
0
6
TsCEI (WR) CE Low to WR Fall 0
Setup Time
6
ThCE (WR) CE to WR Rise
Hold Time
0
0
0
0
6
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
91
Table 47. Z85230/L AC Characteristics (20MHz applies only to Z85230) (Continued)
8.5 MHz
10 MHz
16 MHz
20 MHz
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
18
19
20
21
TsCEh (WR) CE High to WR
Fall Setup Time
58
58
0
38
0
25
0
6
TsCEI (RD) CE Low to RD Fall 0
Setup Time
1, 6
1, 6
1, 6
ThCE ((RD) CE to RD Rise
Hold Time
0
0
0
0
TsCEh (RD) CE High to RD Fall 58
Setup Time
50
30
25
22
23
TwRDI
RD Low Width
145
0
125
0
70
0
65
0
1, 6
6
TdRD (DRA) RD Fall to Read
Data Active Delay
24
25
26
27
TdRDr (DR) RD Rise to Data
Not Valid Delay
0
0
0
0
6
6
6
6
TdRDI
RD Fall to Read
Data Valid Delay
135
38
120
35
70
65
30
90
TdRD (DRz) RD Rise to Read
Data Float Delay
30
TdA (DR)
Addr to Read Data
Valid Delay
210
180
100
28
29
TwWRI
WR Low Width
145
0
125
0
75
0
65
0
6
6
TdWR (DW) WR Fall to Write
Data Valid Delay
20
20
20
20
30
31
32
33
34
ThDW (WR) Write Data to WR
Rise Hold Time
6
TdWR (W)
WR Fall to Wait
Valid Delay
168
168
168
168
100
100
100
100
50
50
50
50
50
50
3, 6
3, 6
TdRD (W)
RD Fall to Wait
Valid Delay
TdWRf
(REQ)
WR Fall to W/REQ
not Valid Delay
50
60
6
8
TdRDf
(REQ)
RD Fall to WR/
REQ Not Valid
Delay
50
60
5,6
8
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
92
Table 47. Z85230/L AC Characteristics (20MHz applies only to Z85230) (Continued)
8.5 MHz
10 MHz
16 MHz
20 MHz
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
35a TdWRr
(REQ)
WR Fall to DTR/
REQ Not Valid
4
4
4
4
7
35b TdWRr
(REQ)
WR Fall to DTR/
REQ Not Valid
168
NA
100
NA
50
60
50
NA
5, 6
8
36
TdRDr
(REQ)
RD Rise to DTR/
REQ Not Valid
Delay
NA
6
37
38
39
40
TdPC (INT) PCLK Fall to INT
Valid Delay
500
320
175
160
6
TdIAi (RD)
INTACK to RD Fall 145
90
50
75
70
45
65
60
4, 6
6
(ACK) Delay
TwRDA
RD (Acknowledge) 145
Width
125
120
TdRDA (DR) RD Fall (ACK) to
Read Data Valid
Delay
135
6
41
42
43
44
45
46
TsIEI (RDA) IEI to RD Fall
(ACK) Setup Time
95
0
95
0
50
60
45
0
6
8
ThIEI (RDA) IEI to RD Rise
(Ack) Hold Time
0
6
TdIEI (IEO) IEI to IEO Delay
Time
95
90
45
40
6
TdPC (IEO) PCLK Rise to IEO
Delay
195
480
175
320
80
80
6
TdRDA
(INT)
RD Fall to INT
Inactive Delay
200
180
3, 6
6
TdRD
(WRQ)
RD Rise to WR
Fall Delay for No
Reset
15
15
10
10
75
10
10
65
47
48
TdWRQ
(RD)
WR Rise to RD
Fall Delay for No
Reset
15
15
6
6
6
TwRES
WR and RD Low
for Reset
145
100
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
93
Table 47. Z85230/L AC Characteristics (20MHz applies only to Z85230) (Continued)
8.5 MHz
Min Max Min Max Min Max Min Max Notes
2, 7
10 MHz
16 MHz
20 MHz
No Symbol
49 Trc
Parameter
Valid Access
4
4
4
4
Recovery Time
Notes:
1. Parameter does not apply to Interrupt Acknowledge transactions.
2. Parameter applies only between transactions involving the ESCC.
3. Open-drain output, measured with open-drain test load.
4. Parameter is system-dependent. For any ESCC in the daisy chain, TdIAi (RD) must be greater than the sum of
TdPC (IEO) for the highest priority device in the daisy chain. TsIEI (RDA) for the ESCC and TdIEI (IEO) for each
device separating them in the daisy chain.
5. Parameter applies to enhanced Request mode only (WR7’ bit 4=1)
6. Units in ns.
7. Units in TcPc.
8. Applies to 8523L (3V version) only
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
94
Figure 33 displays the Z85230/L General Timing Diagram
PCLK
1
W/REQ
Request
2
W/REQ
Wait
3
RTxC,TRxC
Receive
4
7
5
6
RxD
9
8
SYNC
External
10
TRxC,RTxC
Transmit
12
11
TxD
13
TRxC
Output
15
14
RTxC
16
17
TRxC
18
19
20
CTS,DCD
21
22
21
22
SYNC
Input
Figure 33. Z85230/L General Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
95
Table 48 lists the Z85230/L general timing characteristics details. Table 49 on page 98 lists
the Z85230/L Read/Write Timing characteristics details.
Table 48. Z85230/L General Timing Table (20MHz applies only to Z85230)
8.5 MHz
10 MHz
16 MHz
20 MHz
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
1
TdPC (REQ) PCLK to W/REQ
Valid
250
350
200
300
80
70
9
2
TdPC (W)
PCLK to Wait
Inactive
180
170
9
3
TsRXC (PC) RxC to PCLK
Setup Time
NA
NA
NA
NA
1, 4, 9
1, 9
4
TsRXD
(RXCr)
RxD to RXC
Setup Time
0
0
0
0
5
ThRXD
(RxCr)
RxD to RXC
Hold Time
150
0
125
0
50
0
45
0
1, 9
6
TsRXD
(RXCf)
RxD to RXC
Setup Time
1, 5, 9
1, 5, 9
1, 9
7
ThRXD
(RXCf)
RXD to RXC
Hold Time
150
–200
5
125
–150
5
50
–100
5
45
–90
5
8
TsSY (RXC) SYNC to RXC
Setup Time
9
ThSY (RXC) SYNC to RXC
Hold Time
1, 10
10
11
12
13
14
15
TsTXC (PC) TxC to PCLK
NA
NA
NA
NA
2,4
Setup Time
TdTXCf
(TXD)
TxC to TxD
Delay
190
190
200
150
150
140
80
80
80
70
70
70
2, 9
2, 5, 9
9
TdTxCr
(TXD)
TxC to TxD
Delay
TdTXD (TRX) TxD to TRxC
Delay
TwRTXh
RTxC High
Width
130
120
120
80
80
70
70
6, 9
6, 9
TwRTXI
RTxC Low Width 130
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
96
Table 48. Z85230/L General Timing Table (20MHz applies only to Z85230) (Continued)
8.5 MHz
10 MHz
16 MHz
20 MHz
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
16a TcRTX
RTxC Cycle
Time
472
50
400
50
244
31
200
31
6, 7, 9
7, 8, 9
16b TxRX (DPLL) DPLL Cycle
Time Min.
17
TcRTXX
Crystal Osc.
Period
125
130
1000 100
120
1000 61
1000 61
1000 3, 9
18
TwRTXh
TRxC High
Width
80
70
5, 9
19
20
TwTRXI
TcTRX
TRxC Low Width 130
120
400
80
70
6, 9
TRxC Cycle
Time
472
200
200
244
200
6, 7, 9
21
TwEXT
TwSY
DCD or CTS
Pulse Width
120
120
70
70
60
60
9
9
22
SYNC Pulse
Width
Notes:
1. RxC is RTxC or TRxC, whichever is supplying the receive clock.
2. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
3. Both RTxC and SYNC have 30 pF capacitors to ground connected to them.
4. Synchronization of RxC to PCLK is eliminated in divide by four operation.
5. Parameter applies only to FM encoding/decoding.
6. Parameter applies only for transmitter and receiver; DPLL and BRG timing requirements are identical to case
PCLK requirements.
7. The maximum receive or transmit data rate is 1/4 PCLK.
8. Applies to the DPLL clock source only. Maximum data rate of 1/4 PCLK still applies. DPLL clock must have a
50% duty cycle.
9. Units in ns.
10.Units in TcPc.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
97
Figure 34 displays the Z85230/L System Timing Diagram. Table 49 on page 98 lists the
Z85230/L System Timing Characteristics.
RTxC,TRxC
Receive
W/REQ
Request
1
2
W/REQ
Wait
SYNC
Output
3
INT
4
RTxC,TRxC
Transmit
W/REQ
Request
5
W/REQ
Wait
6
DTR/REQ
Request
7
INT
8
CTS,DCD
SYNC
Input
9
INT
10
Figure 34. Z85230/L System Timing Diagram
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
98
Table 49. Z85230/L System Timing Characteristics (20MHz applies only to Z85230)
8.5 MHz
10 MHz
16 MHz
20 MHZ
No Symbol
Parameter
Min Max Min Max Min Max Min Max Notes
1
2
3
TdRXC
(REQ)
RxC to W/REQ
Valid
13
13
4
17
17
7
13
13
4
17
17
7
13
13
4
17
17
7
13
13
4
18
18
8
2, 4
TdRXC (W)
RxC to Wait
Inactive
1, 2, 4
2, 4
TdRXC (SY) RxC to SYNC
2
Valid
4
5
TdRXC (INT) RxC to INT Valid 15
21
13
15
8
21
13
15
8
21
13
15
8
22
12
1, 2, 4
3, 4
TdTXC
(REQ)
TxC to W/REQ
Valid
8
8
7
7
6
7
TdTXC (W)
TxC to Wait
Inactive
14
10
8
7
14
10
8
7
14
10
8
7
15
11
1, 3, 4
3, 4
TdTXC
(DRQ)
TxC to DTR/REQ
Valid
8
TdTXC (INT) TxC to INT Valid
TsSY (INT)
13
7
7
2
3
13
7
7
2
3
13
7
7
2
3
14
7
1, 3, 4
1, 4
9
SYNC to INT Valid 2
10
TdEXT (INT) DCD or CTS to
INT Valid
3
8
8
8
9
1, 4
Notes:
1. Open-drain output, measured with open-drain test load.
2. RxC is RTxC or TRxC, whichever is supplying the receive clock.
3. TxC is TRxC or RTxC, whichever is supplying the transmit clock.
4. Units in TcPc.
PS005308-0609
Electrical Characteristics
Z80230/Z85230/L
Product Specification
99
Z80230/Z85230/L Errata
The current revision of Zilog’s ESCC has six known bugs. This section identifies these
bugs and provides workarounds.
IUS Problem Description
The IUS problem occurs under the following conditions:
•
•
SDLC 10x19 Status FIFO is enabled
Interrupts on Receive Special Conditions only
This mode is intended for an application where received characters are read by a DMA
controller. EOF is treated differently from other special conditions (for example, parity
error, overrun error, and CRC error).
When EOF is detected, the following conditions occur:
•
•
A Receive Character Available (RCA) interrupt is generated, rather than the Special
Conditions interrupt, as in other operating modes.
The data FIFO is not locked, as in other operating modes, and is known as the Anti-
Lock feature.
This feature allows the processor to service the EOF interrupt with more latency. Immedi-
ate attention from the processor is not necessary because the data FIFO is not locked.
Incoming data can still be delivered to the Receive FIFO and not get lost. It also allows for
operation with no servicing of the interrupt.
When the EOF interrupt (RCA interrupt) is serviced, the processor must use the Reset
HighestIUScommand to clear the EOF.
If an EOF interrupt occurs when another lower priority interrupt is enabled (for example,
Ext/Status interrupt is serviced) the ResetHighestIUScommand issued by the lower
priority ISR (to clear out the pending interrupt) can accidentally clear the pending EOF
interrupt.
The ResetHighestIUScommand clears the IP bit related to the EOF (in this mode, the
RCA IP bit) regardless of the priorities of the pending interrupts. This action causes errors
under the following circumstances:
•
•
Another ESCC interrupt is being serviced (for example, an Ext/Status interrupt for
Transmitter Underrun in Full Duplex operation)
The DMA reads a byte marked with EOF. The corresponding IP bit is set to 1 and the
INT line goes Low (highest priority interrupt in the daisy chain).
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
100
•
•
•
The processor does not acknowledge this interrupt because it is servicing another
interrupt.
The processor finishes servicing the other interrupt and uses the ResetHighestIUS
command.
The IP bit reset corresponding to the EOF, and the EOF interrupt is lost.
IUS Problem Solutions
The following methods can be used to work around the previously described problems.
•
Alternate Operating Mode–A similar operating mode can be used to achieve the same
functionality with minimum code modifications. The ESCC must operate in Receive
Interrupts on First Character and Special Condition, instead of Receive Interrupt on
Special Condition Only.
In this mode, the Anti-Lock feature is not enabled. The FIFO is locked after the last
character of a frame has been transferred, and the interrupt condition does not
disappear until after an ErrorResetcommand is issued to the ESCC. No Reset
HighestIUScommand can clear any IP bit.
•
•
Daisy Chain– This workaround uses the following two conditions:
–
–
The EOF interrupt is the highest priority interrupt if only one channel is used.
Channel A is the only channel issuing interrupts.
If both conditions are satisfied, allowing nested interrupts can solve the problem.
The processor servicing an interrupt on the daisy chain must be interruptible again
from another interrupt of higher priority on that same daisy chain.
RR7 Register–This workaround is applicable if the EOF interrupt is used only to
notify another part of the software that there has been another frame received:
–
–
Read RR7 after issuing the ResetIUScommand.
Check bit 6 of RR7. This bit, when set, indicates that the SDLC frame FIFO con-
tains a valid frame. Although one interrupt might have been lost (IP reset) by the
ResetIUScommand, bit 6 of RR7 always indicates that at least one frame is
available in the frame FIFO. If bit 6 of RR7 is 1, notify the concerned part of the
software that at least one frame is available in the frame FIFO.
When the SDLC FIFO is enabled and Receive Interrupts on Special Conditions Only is
selected, software checks that there is a Receive Character Available interrupt, which is
generated by DMA reading an EOF character, and before issuing the ResetHighest
IUScommand. Otherwise, the EOF interrupt conditions are cleared by that command.
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
101
Figure 35 displays the procedure for resetting highest IUS.
DMA read
EOF
Ext/Status
Interrupt
INT
Reset Highest
IUS from
Ext/Status
Handler
Ext/Status IP
RCA IP
Ext/Status IUS
Resetting highest IUS from lower priority interrupt clears the EOF (RCA) interrupt.
Figure 35. Resetting Highest IUS from Lower Priority
RTS Problem Description
The ESCC (Z80230/Z85230/L) contains a functional problem in Automatic RTS Deacti-
vation (see Figure 36 on page 102).
This mode is intended for SDLC applications where the RTS signal from the ESCC is used
to enable a line driver in multi-drop line communications.
Before the frame transmission, RTS is asserted by an ActivateRTScommand (ER5 bit1
equals 0).
After the last data bit of a frame is sent, a Transmit Underrun interrupt is requested. A
DeactivateRTScommand is issued (WR5 bit 1 equals 1) to deactivate the RTS signal to
turn off the line driver after the multiple-frame packet is sent.
On the SCC, the processor must monitor the data line to ensure that the frame has been
sent before it issues the DeactivateRTScommand.
On the ESCC, RTS can be programmed to deactivate automatically after the frame is sent.
If the following sequence is performed, additional monitoring is not required:
1. Enable Automatic RTS Deactivation (WR7’ bit 2 equals 1).
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
102
2. Enable the CRC/Flag on Underrun (WR10 bit 2 equals 0).
3. Issue a DeactivateRTScommand in the Transmit Underrun ISR. The RTS signal
deactivates automatically after the closing flag disappears.
The Automatic RTS Deactivationcommand works for a single frame and for two
consecutive frames back-to-back. This command does not work with more than two back-
to-back frames.
In the latter condition, if the DeactivateRTScommand is issued at the beginning of the
TransmitUnderrunISR. RTS is deactivated after the CRC is gone, but before the clos-
ing flag is sent. The final frame is not concluded, and is corrupted.
RTS Problem Solutions
A workaround for the RTS problem is not to send back-to-back frames. Idle time is
inserted between frames.
There is, however, a limitation to this workaround in that the system throughput is reduced
by the idle time inserted between the frames.
Figure 36 displays Automatic RTS Deactivation.
Frame n
Frame n-1
RTS
TxD
Flag Frame n-1 CRC Flag Frame n CRC Flag
RTS deactivates correctly (after the closing flag)
if only one back-to-back frame is sent.
Frame n
Frame n-1
RTS
TxD
RTS must deactivate
after the last closing
flag is gone.
Flag Frame n-1 CRC Flag Frame n CRC Flag
RTS deactivates too soon, after the CRC, but before the closing
flag if more than two back-to-back frames are sent.
Figure 36. Automatic RTS Deactivation
Automatic TxD Forced High Problem Description
If WR10 is programmed with bits 6 and 5 equal to 01 (NRZI), bit 3 equals 1 (Mark Idle)
and WR4 bits 5 and 4 equal 10 (SDLC), the TxD pin is forced High after detecting the last
bit of the closing flag at the falling edge of TxC. This feature does not work if back-to-
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
103
back frames are sent. The TxD output is automatically forced High for eight bit-times and
the first byte of the second frame is corrupted. In a multiple-frame transmission, a zero (0)
bit is inserted before the opening flag of the second frame.
Automatic TxD Forced High Problem Solutions
Send back-to-back frames in FLAG IDLE mode, because the Automatic TxD Forced High
feature creates problems only if all the following conditions are true:
•
•
•
Back-to-back frame transmission
NRZI
Mark Idle
Setting the system in Flag Idle mode (WR10 bit 3 equals 0) in frame transmission allows
back-to-back frames to be sent without any data corruption.
SDLC FIFO Overflow Problem Description
In SDLC mode, bit 7 of RR7 (FIFO Overflow status bit) is set if an 11th frame ends while
the FIFO is full (that is, ten frames have accumulated in the Status FIFO and have not yet
been read by the processor). Under this circumstance, the status FIFO is locked and no
data can be written to the Status FIFO until bit 7 of RR7 is reset.
If the ESCC is set up in ANTI-LOCK mode (that is, the SDKC FIFO is used when
Receive Interrupts on Special Condition Only is enabled), the only method of resetting bit
7 of RR7(the FIFO Overflow bit) is to reset and set WR15 bit 2 (SDLC FIFO Enable Bit).
This action causes the SDLC FIFO to reset and all the SDLC frame information is lost.
With no Anti-Lock feature, the FIFO Overflow status bit is reset if the SDLC FIFO is
read.
If the ESCC is in NRZI and Mark Idle in back-to-back frame transmission, (one the FIFO
Overflow bit RR7 bit 7) is set, the only method of resetting the status is to reset and set
WR15 bit 2. This action causes the SDLC FIFO to reset and the unprocessed frame infor-
mation stored in the SDLC FIFO is lost.
SDLC FIFO Overflow Problem Solution
Do not use Receive Interrupts on Special Conditions Only and Mark Idle if there is a pos-
sibility of Status FIFO Overflow.
Default RR0 Value Problem Description
RR7 bit 7, the Break/Abort status bit, does not always clear after reset.
Default RR0 Value Problem Solution
Ignore the first bit 7 value read from RR0 after reset.
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
104
Default RR10 Value Problem Description
RR10 bit 6, the 2 clock missing bit, is sometimes erroneously set to indicate that the DPLL
detects a clock edge in two successive tries after hardware reset.
Default RR10 Value Problem Solution
Ignore the first bit 7 value Read from RR10 after reset.
CRC Problem Description
The CRC cannot be interpreted from the Receive FIFO when one or two residue bits are
sent. The CRC value is received and checked correctly but is not loaded to the Receive
FIFO. The two types of CRC problems are described below:
•
Two Residue bits (Residue code is 000)
The last three bytes of the Receive FIFO read:
D7
D6
D5
D4
D3
D2
D1
D9
C9
D0
D8
C8
C5
C4
C3
C2
C1
C0
C15
C14
C13
C12
C11
C10
Bits 6 and 7 of the CRC are lost.
One Residue Bit (Residue code is 111)
The last three bytes of the Receive FIFO read:
•
D7
D6
D5
D4
D3
D2
D1
C0
C9
D0
D8
C8
C6
C5
C4
C3
C2
C1
C15
C14
C13
C12
C11
C10
Bit 7 of the CRC is lost.
The CRC is received and loaded into the Receive FIFO in other situations (that is, the 0, 3,
4, 5, 6, and 7 residue bits).
The Residue code, RR1 bits 3, 2, and 1, is reported independently of the number of residue
bits sent.
CRC Problem Solution
Ignore the CRC value read from the Receive FIFO if one or two residue bits are sent.
PS005308-0609
Z80230/Z85230/L Errata
Z80230/Z85230/L
Product Specification
105
Package Information
Figure 37 displays the 40-pin Dual-Inline Package (DIP).
E
1
20
C
E1
eA
MILLIMETER
INCH
MAX
40
21
SYMBOL
D
MIN
MAX
MIN
A1
0.51
0.81
.020
.128
.015
.040
.009
2.050
.600
.535
.032
.135
.021
.060
.015
2.070
.620
.560
A2
B
3.25
3.43
A2
L
A1
0.38
0.53
B1
C
1.02
1.52
B1
B
E
S
0.23
0.38
D
52.07
15.24
13.59
52.58
15.75
14.22
E
E1
2.54 TYP
.100 TYP
E
eA
L
15.49
3.18
1.52
1.52
16.51
3.81
1.91
2.29
.610
.125
.060
.060
.650
.150
.075
.090
Q1
S
Controlling Dimensions: Inch
Figure 37. 40-Pin DIP Package Diagram
PS005308-0609
Package Information
Z80230/Z85230/L
Product Specification
106
Figure 38 displays the 44-pin Plastic Leaded Chip Carrier (PLCC) package.
h
A
D
D1
A1
0.71/0.51
.028/.020
45°
6
1
40
7
39
e
0.51/0.36
0.020/0.014
M
E1 E
0.81/0.66
0.032/0.026
17
29
18
28
R 1.14/0.64
0.045/0.025
MILLIMETER
INCH
MIN MAX
SYMBOL
MIN
4.27
MAX
4.57
A
A1
0.168
0.095
0.685
0.650
0.600
0.180
0.115
0.695
0.656
0.630
2.41
2.92
D/E
D1/E1
D2
17.40
16.51
15.24
17.65
16.66
16.00
NOTES:
1. CONTROLLING DIMENSION : INCH
2. LEADS ARE COPLANAR WITHIN 0.004".
3. DIMENSION : MM
INCH
e
1.27 BSC
0.050 BSC
Figure 38. 44-Pin PLCC Package Diagram
PS005308-0609
Package Information
Z80230/Z85230/L
Product Specification
107
Ordering Information
Order the required ESCC from Zilog using the following part details. For more informa-
tion on ordering, consult your local Zilog sales offices. The Zilog website
(www.zilog.com) lists all the regional offices and provides additional product information.
Z8523L (3.3V)
Z8523L Available Packages
8 MHz Z8523L
10 MHz Z8523L
16 MHz Z8523L
Z8523L08VSG
Z8523L08VEG
Z8523L10VSG
Z8523L10VEG
Z8523L16VSG
Z8523L16VEG
Z85230 (5V)
Z85230 Available Packages
8 MHz Z85230
Z8523008PSG
Z8523008VSG
Z8523008PEG
Z8523008VEG
10 MHz Z85230
16 MHz Z85230
20 MHz Z85230
Z8523010PSG
Z8523010VSG
Z8523010PEG
Z8523010VEG
Z8523016PSG
Z8523016VSG
Z8523016PEG
Z8523016VEG
Z8523020PSG
Z8523020VSG
PS005308-0609
Ordering Information
Z80230/Z85230/L
Product Specification
108
Z80230
Z80230 Available Packages
10 MHz Z80230
Z8023010PSG
Z8023010VSG
16 MHz Z80230
Z8023016PSG
Z8023016VSG
Part Number Suffix Designation
Z
80230
16
P
S
G
Environmental Flow
G = Green Plastic Packaging
Compound
Temperature
E = -40C to +100C
S = 0C to +70C
Package
P = Plastic DIP (PDIP)
V = Plastic LCC (PLCC)
Speed
8 = 8.0 MHz
10 = 10.0 MHz
16 = 16.384 MHz
20 = 20 MHz
Product Number
Zilog Prefix
PS005308-0609
Ordering Information
Z80230/Z85230/L
Product Specification
112
Customer Support
For answers to technical questions about the product, documentation, or any other issues
with Zilog’s offerings, please visit Zilog’s Knowledge Base at
http://www.zilog.com/kb.
For any comments, detail technical questions, or reporting problems, please visit Zilog’s
Technical Support at http://support.zilog.com.
PS005308-0609
Customer Support
Z80230/Z85230/L
108
D
Index
data communications capabilities 15
data encoding 20
DC characteristics 77
default RR0 value problem
description 103
solution 103
default RR10 value problem
A
abort character 18
absolute maximum ratings 75
AC characteristics 78
AC characteristics table, Z85230 90
AC characteristics, Z85230 87
asynchronous receive mode 4
auto echo and logical loopback 21
auto enable 4
description 104
solution 104
device type identification 24
diagram
40-pin DIP package 105
44-pin PLCC package 106
automatic RTS deactivation 102
cycle timing, Z85230 89
data encoding methods 20
detecting 5-or 7-bit characters 16
DPLL Outputs 27
automatic EOM reset 28
B
baud rate generator 19
bisync 4, 16
block transfer, CPU/DMA 15
ESCC protocols 15
general timing, Z80230 81
general timing, Z85230 94
interrupt acknowledge cycle timing, Z80230
72
C
capacitance 76
character
interrupt acknowledge cycle timing, Z85230
74
abort 18
interrupt acknowledge timing, Z80230 80
interrupt acknowledge timing, Z85230 89
interrupt priority schedule 13
read cycle timing, Z80230 71
read cycle timing, Z85230 73
read/write timing, Z80230 79
read/write timing, Z85230 88
receive data path 9
reset timing, Z80230 80
reset timing, Z85230 89
resetting highest IUS from lower priority 101
SDLC frame status FIFO 29
SDLC loop 18
EOP 18
code
NRZ 18
NRZI 18
command
reset highest IUS 28
reset Tx CRC generator 28
reset Tx/underrun latch 28
counter
transmit clock 5
CRC problem
description 104
solution 104
standard and open-drain test conditions 76
system timing, Z80230 86
system timing, Z85230 98
transmit data path 8
CRC reception in SDLC mode 26
Customer Feedback Form 112
TxIP latching 27
PS005308-0609
P R E L I M I N A R Y
Index
Z80230/Z85230/L
109
write cycle timing,Z85230 74
Z80230 pin assignments 3
Z80230 pin functions 2
Z85230 pin assignments 3
Z85230 pin functions 2
INTACK 13
interface timing, Z80230 70
internal synchronization 4
interrupt acknowledge cycle timing
Z80230 71
digital phase-locked loop 5, 19
DPLL counter Tx clock source 27
Z85230 74
interrupts 12
external/status 13, 14
interrupt cknowledge (INTACK) 13
interrupt enable (IE) 12
interrupt on all receive characters or special re-
ceive conditions 14
E
encoding, data 20
end of poll (EOP) character 18
enhancements
receive FIFO, 8 bytes 22
transmit FIFO, 4 bytes 22
Z80230 and Z85230 22
EOP 18
errata 99
ESCC
programming 32
read registers 53
write registers 32
external synchronization 4
interrupt on first receive character or special re-
ceive condition 14
interrupt on special receive conditions only 14
interrupt pending (IP) 12, 13
interrupt under service (IUS) 12, 13
receive 13
receive character available 22
transmit 13
transmit buffer empty 22, 24
Tx underrun/EOM 28
IUS latch 28
IUS problem
description 99
solutions 100
F
FIFO
anti-lock feature 31
enable/disable 30
read operation 30
write operation 31
functional description 8
L
latch
ISU 28
RR0 27
TxIP 26
local loopback 21
G
general timing characteristics table, Z80230 82
general timing table, Z85230 95
M
mark idle 26
mode
1x 18
I
asynchronous receive 4
auto echo 21
request on transmit 24
SDLC 17
identification, device types 24
IE 12
input/output capabilities 9
PS005308-0609
P R E L I M I N A R Y
Index
Z80230/Z85230/L
110
SDLC loop 18
SDLC status FIFO 19
synchronous 16
SYNCB 4
TRxCA 5
TRxCB 5
TxDA 5
monosync 4, 16
TxDB 5
W/REQA 5
W/REQB 5
pins, Z80230 exclusive
A7-A0 6
N
no vector (NV) 28
NV 28
AS 7
CS0 7
CS1 7
DS 7
R/W 6
O
ordering information 107
pins, Z85230 exclusive
CE 6
Channels A/B 6
D/C 6
D7-D0 6
RD 6
P
package information 105
part number descriiption 108
pin assignments
Z80230 3
WR 6
Z85230 3
polynomial, SDLC CRC 17
pin descriptions 1
pin functions
Z80230 2
R
Z85230 2
ratings, absolute maximum 75
read cycle timing
pins, common
CTSA 4
CTSB 4
DCDA 4
DCDB 4
DTR/REQA 4
DTR/REQB 4
IEI 5
IEO 5
INT 6
INTACK 6
PCLK 5
RTSA 4
RTSB 4
RTxCA 5
Z80230 71
Z85230 73
read register (RR) 10
read registers 53
receive conditions 14
request on receive 22
request on transmit 22
request on transmit mode 24
reset highest IUS command 28
reset Tx CRC generator command 28
reset Tx/underrun EOM latch 28
RR 10
RR0 latch 27
RTS problem
RTxCB 5
description 101
solutions 102
RxDA 5, 16
RxDB 5, 16
SYNCA 4
PS005308-0609
P R E L I M I N A R Y
Index
Z80230/Z85230/L
111
write cycle timing
Z80230 70
Z85230 73
write register (WR) 10
write register 7 prime (WR&’) 23
write register 7 prime (WR7’) 9
S
SDLC
CRC polynomial 17
FIFO frame status enhancement 28
loop mode 18
mode, CRC reception 26
mode, TxD forced high 26
status FIFO 19
bit 0 25
bit 1 25
bit 2 25
bit 3 25
bit 4 24
bit 5 24
bit 6 24
bit 7 24
status FIFO anti-lock feature 31
transmit data interrupt response 28
SDLC FIFO overflow problem
description 103
solutions 103
SDLC mode 17
write registers 32
software interrupt acknowledge 28
standard test conditions 75
synchronization
external 4
internal 4
synchronous modes 16
system timing characteristics table, Z85230 98
T
timing, Z85230 72
transmit buffer empty interrupt 22
transmit clock counter 5
Tx underrun/EOM interrupt 28
TxD forced high in SDLC mode 26
TxD forced high problem
description 102
solutions 103
TxIP latch 26
V
vector includes status (VIS) 28
VIS 28
W
WR 10
WR7’ 9, 23
PS005308-0609
P R E L I M I N A R Y
Index
相关型号：
Z8523010PEG
Serial I/O Controller, 2 Channel(s), 0.3125MBps, CMOS, PDIP40, GREEN, PLASTIC, DIP-40
IXYS
Z8523010PEG
IC 2 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PDIP40, GREEN, PLASTIC, DIP-40, Serial IO/Communication Controller
ZILOG
Z8523010PSG
IC 2 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PDIP40, GREEN, PLASTIC, DIP-40, Serial IO/Communication Controller
ZILOG
Z8523010VEG
Serial I/O Controller, 2 Channel(s), 0.3125MBps, CMOS, PQCC44, GREEN, PLASTIC, LCC-44
IXYS
Z8523010VEG
IC 2 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PQCC44, GREEN, PLASTIC, LCC-44, Serial IO/Communication Controller
ZILOG
Z8523010VSG
Serial I/O Controller, 2 Channel(s), 0.3125MBps, CMOS, PQCC44, GREEN, PLASTIC, LCC-44
IXYS
©2020 ICPDF网 联系我们和版权申明