JSF-21S2AA1 [JDSU]
Fibre Channel Small Form Factor PTH Transceiver;型号: | JSF-21S2AA1 |
厂家: | JDSU |
描述: | Fibre Channel Small Form Factor PTH Transceiver |
文件: | 总23页 (文件大小:1380K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
.
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Features
Applications
• International Class 1 laser safety certified
• 1.0625 Gb/s or 2.125 Gb/s data rates
• 1x and 2x (ANSI) Fibre Channel compliant [1]
• Short wavelength (SW) (distance £ 500 m)
• 3 mm pin length for standard boards
• 4.5 mm pin length for thick boards
• Low Power Dissipation, 500 mW Typical
• LVTTL Signal-Detect Output
• 2x Gigabit Fibre Channel
• Gigabit Fibre Channel
• Client/Server environments
• Distributed multi-processing
• Fault tolerant applications
• Visualization, real-time video, collaboration
• Channel extenders, data storage, archiving
• Data acquisition
• AC coupling of PECL signals
• Single +3.3 +/-10% V Power Supply
• Withstand normal wave solder and aqueous
spray cleaning
• UL and TUV approved
-12
• Low bit error rate (< 10
)
• High reliability AFR < 0.01%/khr@50°C, 100 FIT
Description
The 1.0625/2.125 Gbps Small Form Factor (SFF-
PTH-SW-2X5/2X6) is an integrated fiber optic trans-
ceiver that provides a high-speed serial link at a sig-
naling rate up to 2.125 Gb/s. The SFF-PTH-SW-
2X5/2X6 conforms to the American National Stan-
dards Institute’s (ANSI) Fibre Channel, FC-PI speci-
fication for short wavelength operation (200-M5-SN-
I, 200-M6-SN-I,100-M5-SN-I, and 100-M6-SN-I).
Laser) source. This enables low cost data transmis-
sion over optical fibers at distances up to 500m at
1.0625 Gb/s and 300 m at 2.125 Gb/s. A 50/125 mm
multimode optical fiber, terminated with an industry
standard LC connector, is the preferred medium. (A
62.5/125 mm multimode fiber can be substituted with
shorter maximum link distances.)
Encoded (8B/10B) [3], [4], gigabit/sec serial differen-
tial PECL signals traverse a PTH connector interfac-
ing the SFF-PTH-SW-2X5/2X6 to the host card. The
serial data modulates the laser and is sent out over
the outgoing fiber of a duplex cable.
The transceiver is insensitive to the data rate of the
incoming electrical and optical signals. The trans-
ceiver complies with the 1.0625 Gb/s and 2.125
Gb/s Fibre Channel Standard without an external
control signal.
Incoming modulated light is detected by a photore-
ceiver mounted in the LC receptacle. The optical
signal is converted to an electrical one, amplified
and delivered to the host card. This module is
designed to work with industry standard “10b” Seri-
alizer/Deserializer modules.
The SFF-PTH-SW-2X5/2X6 is ideally suited for
Fibre Channel applications which include point to
point links as well as Fibre Channel Arbitrated Loop
(FC-AL). It can also be used for other serial applica-
tions where high data rates are required. This speci-
fication applies to a pin through hole (PTH) module
which has a 2 by 5 or 2 by 6 electrical connector pin
configuration.
The SFF-PTH-SW-2X5/2X6 is a Class 1 laser safe
product. The optical power levels, under normal
operation, are at eye safe levels. Optical fiber cables
can be connected and disconnected without shutting
off the laser transmitter.
The SFF-PTH-2125-SW uses a short wavelength
(850nm) VCSEL (Vertical Cavity Surface Emitting
03/06/02
Page 1 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Package Outline
Pin Assignments
Pin Name
Rx Ground
Type
Ground
Pin #
1
Rx Power
Rx_SD
Power
2
Status Out
Signal Out
Signal Out
Power
3
Rx_DAT -
Rx_DAT +
Tx Power
Tx Ground
Tx_Disable
Tx_DAT +
Tx_DAT -
N/C
4
5
6
Ground
7
Control In
Signal In
Signal In
Not Connected
Status Out
8
9
10
A
Tx_Fault (2X6 Only)
B
Ordering Information
Product Descriptor
Part Number
Signaling Rate
Wavelength
Pin Length
2.125 Gb/s
2.125 Gb/s
2.125 Gb/s
2.125 Gb/s
850 nm
850 nm
850 nm
850 nm
SFF-PTH-2125-SW-2X5-3
SFF-PTH-2125-SW-2X5-3
SFF-PTH-2125-SW-2X6-45
SFF-PTH-2125-SW-2X6-45
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
3.0 mm
3.0 mm
4.5 mm
4.5 mm
Laser Safety Compliance Requirements
ulations contained in 21 CFR(J) or CENELEC regu-
lations contained in EN 60825. The person(s)
performing such an act is required by law to recertify
and reidentify the product in accordance with the
provisions of 21 CFR(J) for distribution within the
United States, and in accordance with provisions of
CENELEC EN 60825 (or successive regulations) for
distribution within the CENELEC countries or coun-
tries using the IEC 825 standard.
The SFF-PTH-SW-2X5/2X6 is designed and certi-
fied as a Class 1 laser product. If the power supply
voltage exceeds 5.0 volts, the transceiver may no
longer remain a Class 1 product. The system using
the SFF-PTH-SW-2X5/2X6 must provide power sup-
ply over voltage protection that guarantees the sup-
ply does not exceed 5.0 volts under all fault
conditions. If the voltage exceeds 4.0 volts, the reli-
ability of the part may be compromised.
ESD Notice
Caution: Operating the power supply above 5.0
volts or otherwise operating the SFF-PTH-SW-
2X5/2X6 in a manner inconsistent with its design
and function may result in hazardous radiation expo-
sure, and may be considered an act of modifying or
new manufacturing of a laser product under US reg-
It is advised that normal static precautions be taken
in the handling and assembly of the SFF-PTH-SW-
2X5/2X6 to prevent damage and/or degradation
which may be introduced by electrostatic discharge.
03/06/02
Page 2 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Block Diagram
Optical
Electrical
Receive Section
Fiber
Input
+Rx_DAT
-Rx_DAT
Post-amp
and
Photoreceiver
Signal Detect
Rx_SD
Transmit Section
Fiber
Output
Laser
+Tx_DAT
-Tx_DAT
AC Modulation
DC Drive
and
Safety Control
Tx_Disable
Fault
Sense
Tx_Fault
(Only available on 2 X 6)
Transmit Section
The input, an AC coupled differential data stream from the host, enters the AC Modulation section of the laser
driver circuitry where it modulates the output optical intensity of a semiconductor laser. The DC Drive main-
tains the laser at the correct preset power level. In addition, safety circuits in the DC Drive will shut off the
laser if a fault is detected. The transceiver provides the AC coupling for the +Tx/-Tx lines. No AC coupling
capacitors are required on the host card for proper operation.
Receive Section
The incoming modulated optical signal is converted to an electrical signal by the photoreceiver. This electrical
signal is then amplified and converted to a differential serial output data stream and delivered to the host. A
transition detector detects sufficient AC level of modulated light entering the photoreceiver. This signal is pro-
vided to the host as a signal detect status line. The transceiver provides the AC coupling for the +Rx/-Rx
lines. No AC coupling capacitors are required on the host card for proper operation.
03/06/02
Page 3 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Input Signal Definitions
Levels for the signals described in this section are listed in Transmit Signal Interface on page 8 and Control
Electrical Interface on page 9.
Tx_DAT
A differential PECL serial data stream is presented to the SFF-PTH-SW-2X5/2X6 for transmission onto an
optical fiber by modulating the optical output intensity of the laser.
Tx_Disable
When high (a logical one), the Tx_Disable signal turns off the power to both the AC and DC laser driver cir-
cuits. It will also reset a laser fault if one should happen. When low (a logical zero), the laser will be turned on
within 1 ms if a hard fault is not detected. The transceiver contains a pull-down resistor to enable the laser
when the line is not connected on the host side. If driven, this line should be connected to a push-pull output
driver.
Timing of Tx_Disable Function
t_reset
> 10ms
Tx_Disable
Transmitter optical
signal
t_off
t_on
< 1ms
< 10ms
03/06/02
Page 4 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Output Signal Definitions
Levels for the signals described in this section are listed in Receive Signal Interface on page 8 and Control
Electrical Interface on page 9.
Rx_DAT
The incoming optical signal is converted and repowered as a differential PECL serial data stream. The
Receive Signal Interface table on page 8 gives the voltage levels and timing characteristics for the Rx_DAT
signals.
Rx_SD
The Receive Signal Detect line is high (a logical one) when the incoming modulated light intensity is sufficient
for reliable operation. This is the state for normal operation. The line is low (a logical zero) when incoming
modulated light intensity is the below that required to guarantee the correct operation of the link. Normally,
this only occurs when either the link is unplugged or the companion transceiver is turned off. This signal is
normally used by the system for diagnostic purposes.
This signal has a push-pull output driver.
Tx_Fault (Only available on 2 X 6)
Upon sensing an improper power level in the laser driver, the SFF sets this signal high and turns off the laser.
The Tx_Fault signal can be reset with the Tx_Disable line.
The laser is turned off within 100 ms as shown in the Transmitter Fault Detection timing diagram below.
This signal has an open drain TTL driver. A pull up resistor is required on the host side of the SFF connector.
The recommended value for this resistor is 10 kW.
Transmitter Fault Detection
Receive Signal Detection
transmitter
safety fault
Optical Signal
Rx_SD
Signal Removed
Tx_Fault
Optical
Power
t_SD_off
<100ms
t_SD_on
<100ms
t_fault
<100ms
Tx_Fault option is only available on 2 X 6
03/06/02
Page 5 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Operation
Initialization Timings
SFF-PTH-2125-SW-2X5/2X6
with Tx_Disable De-asserted
SFF-PTH-2125-SW-2X5/2X6
with Tx_Disable Asserted
Vcc > 3.15V
Vcc > 3.15V
Tx_Fault
Tx_Fault
Tx_Disable
1
0
Tx_Disable
Optical Transmit
Signal
Optical Transmit
Signal
t_init
< 300ms
< 300ms
t_init
Tx_Fault option is only available on 2 X 6
Tx_Fault option is only available on 2 X 6
Resetting a Laser Fault
Resetting a laser fault by toggling the Tx_Disable input will permit the SFF-PTH-SW-2X5/2X6 to attempt to
power on the laser following a fault condition. Continuous resetting and re-powering of the laser under a hard
fault condition could cause a series of optical pulses with sufficient energy to violate laser safety standards.
To alleviate the possibility of violating laser safety standards, the SFF-PTH-SW-2X5/2X6 will turn off the laser
if a second fault is detected within 25 ms of the laser powering on. This lock is cleared during each power on
cycle. Please refer to the timing diagrams below.
Successful Recovery from a
Transmitter Safety Fault
Unsuccessful Recovery from a
Transmitter Safety Fault
Occurrence
of transmitter
safety fault
Occurrence
of transmitter
safety fault
Tx_Fault
Tx_Fault
Tx_Disable
Tx_Disable
Optical
Power
Optical
Power
t_fault
t_reset
<100ms
t_reset
>10ms
>10ms
t_init*
<300ms
t_init*
<300ms
Tx_Fault option is only available on 2 X 6
*only if the fault is transient
Tx_Fault option is only available on 2 X 6
*only if the fault is transient
03/06/02
Page 6 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Absolute Maximum Ratings
Symbol
TS
Parameter
Storage Temperature
Min.
-40
0
Typical
Max.
85
Unit
°C
%
Notes
1
RHS
VCC
Relative Humidity–Storage
Supply Voltage
95
1, 2
-0.5
0
4.0
V
1
1
VI
VCC + 0.7
TTL DC Input Voltage
V
TSOLD
TSOLD
Connector Pin Temp during soldering
Optics Temperature during soldering
165/5
1,3
4
°C/s
°C/s
100/60
1. Stresses listed may be applied one at a time without causing permanent damage. Exposure to these values for extended periods
may affect reliability. Specification Compliance is only defined within Specified Operating Conditions.
2. Non-condensing environment.
3. The connector pin temperature can be measured with a thermocouple attached to pin 3 of the header.
4. The optics temperature can be measured with a thermocouple on the device with the cover off.
Specified Operating Conditions
Symbol
TOP
Parameter
Ambient Operating Temperature
R
Supply Voltage
Min.
0
Typical
3.3
Max.
70
Unit
°C
V
VDDT, VDD
RHOP
2.97
8
3.63
80
Relative Humidity-Operating
%
Power Supply Interface
Symbol
ITx
Parameter
Min
Typical
60
Max.
Unit
mA
Tx Power Current (@ 3.3 V)
Rx Power Current (@ 3.3 V)
Tx Power Current (@ 3.63 V)
Rx Power Current (@ 3.63 V)
Tx Power Dissipation (@ 3.3 V)
Rx Power Dissipation (@ 3.3 V)
Tx Power Dissipation (@ 3.63 V)
Rx Power Dissipation (@ 3.63 V)
Ripple & Noise
IRx
ITx
90
mA
85
mA
IRx
115
mA
PTx
PRx
PTx
PRx
200
300
mW
mW
300
400
100
mW
mW
mV (pk-pk)
03/06/02
Page 7 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Transmit Signal Interface (from host to SFF-PTH-SW-2X5/2X6)
Symbol
Vo
Parameter
Min
400
Max.
2000
0.14
Unit
mV
UI
Notes
1
PECL Amplitude
PECL Deterministic Jitter
DJelec-xmit
TJelec-xmt
2,4
PECL Total Jitter
PECL Rise/Fall
0.26
200
20
UI
ps
ps
2,4
3,4
4
50
PECL Differential Skew
1. At 100W, differential peak-to-peak, the figure below shows the simplified circuit schematic for the SFF-PTH-SW-2X5/2X6 high-
speed differential input lines. The PECL input data lines have AC coupling capacitors. The capacitors are not required on the host
card.
VDD
+Tx_DAT
2.4kW
50W
3.8kW
8pF
50W
-Tx_DAT
2. Deterministic jitter (DJ) and total jitter (TJ) values are measured according to the methods defined in [2]. Jitter values at the output
of a transmitter or receiver section assume worst case jitter values at its respective input. [1UI(Unit Interval)=470.6ps at 2.125Gb/s]
3. Rise and fall times are measured from 20 - 80%, 100W differential.
4. When in 1Gb/s mode the transceiver is compliant with 1G specifications as defined in [1].
Receive Signal Interface (from SFF-PTH-SW-2X5/2X6 to host)
Symbol
Vo
Parameter
Min
600
Max.
1000
0.39
0.64
Unit
mV
UI
Note(s)
1
PECL Amplitude
PECL Deterministic Jitter
PECL Total Jitter
DJelec-rcv
TJelec-rcv
2,3
UI
2,3
1. At 100W, differential peak-to-peak, the figure below shows the simplified circuit schematic for the SFF-PTH-SW-2X5/2X6 high-
speed differential output lines. The PECL input data lines have AC coupling capacitors. The capacitors are not required on the host
card.
Rx_VDD
50W
50W
+Rx_DAT
-Rx_DAT
...
Rx_Gnd
2. Deterministic jitter (DJ) and total jitter (TJ) values are measured according to the methods defined in [2]. Jitter values at the output
of a transmitter or receiver section assume worst case jitter values at its respective input. [1UI(Unit Interval)=470.6ps at 2.125Gb/s]
3. When in 1Gb/s mode the transceiver is compliant with 1G specifications as defined in [1]. 1UI(Unit Interval)=941.2ps at
1.0625Gb/s)
03/06/02
Page 8 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Control Electrical Interface
Symbol
Voltage Levels
VOL
Parameter
Min
Max.
Unit
Note(s)
0.0
0.50
V
V
V
V
TTL Output (from SFF-PTH-SW-2X5/2X6)
VOH
VIL
VCC-0.5
VCC+0.3
0
0.8
TTL Input (to SFF-PTH-SW-2X5/2X6)
1
VIH
VDDT+0.3
2.0
Timing Characteristics
t_off
t_on
Tx_Disable Assert time
10
1
2
2
2
3
3
4
4
ms
ms
ms
ms
ms
ms
ms
Tx_Disable De-assert time
Tx_Disable Time to start reset
Initialization Time
t_reset
t_init
10
300
100
100
100
t_fault
t_SD_on
t_SD_off
Tx_Fault Assert Time (only available on the 2 X 6)
Rx_SD Assert Delay
Rx_SD De-Assert Delay
1. A 1 kW pull-down resistor to GND is present on the SFF-PTH-SW-2X5/2X6 to allow the laser to be active when no input signal is
provided on Tx_Disable.
2. See Tx_Disable on page 4 for timing relationships.
3. See Operation on page 6
4. See Rx_SD on page 5 for timing relations.
03/06/02
Page 9 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Optical Receiver Specifications (Short Wavelength)
Symbol
l
Parameter
Operating Wavelength
Min
830
12
Typical
Max.
860
Unit
nm
Notes
RL
Return Loss of Receiver
dB
OMA
OMA
Poff
Optical Modulation Amplitude - 2.125Gb/s
Optical Modulation Amplitude - 1.0625Gb/s
Rx_SD De-Assert (negate) Level
49
2000
2000
-17.5
1, 2
1, 2
3
mW (pk-pk)
mW (pk-pk)
dBm (avg)
31
-27.0
Pon
Rx_SD Assert Level
Rx_SD Hysteresis
-17.0
5.0
dBm (avg)
3
3
0.5
2.5
dB (optical)
1. The minimum and maximum values of the average received power in dBm give the input power range to maintain a
BER < 10-12 when the data is sampled in the center of the receiver eye. These values take into account power penalties caused by
the use of a laser transmitter with a worst-case combination of spectral width, extinction ratio and pulse shape characteristics.
2. Optical Modulation Amplitude (OMA) is defined as the difference in optical power between a logic level one and a logic level zero.
The Optical Modulation Amplitude is defined in terms of average optical power (PAVG in mW) and extinction ratio (ER) as given by
OMA=2PAVG((ER-1)/(ER+1)). The extinction ratio, defined as the ratio of the average optical power (in mW) in a logic level one to
the average optical power in a logic level zero measured under fully modulated conditions in the presence of worst case reflec-
tions, must be the absolute (unitless linear) ratio and not expressed in dB.The specified Optical Modulation Amplitude at 2.125Gb/s
is equivalent to an average power of -15 dBm at an extinction ratio of 9 dB. At 1.0625Gb/s, the specified OMA is equivalent to an
average power of -17 dBm at an ER of 9 dB.
3. The Rx_SD has hysteresis to minimize “chatter” on the output line. In principle, hysteresis alone does not guarantee chatter-free
operation. The SFF-PTH-SW-2X5/2X6, however, presents an Rx_SD line without chatter, where chatter is defined as a transient
response having a voltage level of greater than 0.5 volts (in the case of going from the negate level to the assert level) and of any
duration that can be sensed by the host logic.
03/06/02
Page 10 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Optical Transmitter Specifications (Short Wavelength)
Symbol
Parameter
Min
830
Typical
Max.
860
Unit
nm
Notes
l C
Spectral Center Wavelength
Spectral Width
0.85
-4.0
150
nm (rms)
dBm (avg)
ps
Dl
PT
Launched Optical Power
-10
1
2
3
3
Trise/Tfall
Optical Rise/Fall Time
OMA
OMA
RIN12
Optical Modulation Amplitude (2.125Gb/s)
Optical Modulation Amplitude (1.0625Gb/s)
196
156
mW (pk-pk)
mW (pk-pk)
Relative Intensity Noise
Eye Opening
-117
0.26
dB/Hz
UI
4
5
6
7
0.56
9
DJ
Deterministic Jitter
Coupled Power Ratio
UI
CPR
dB
1. Launched optical power is measured at the end of a two meter section of a 50/125mm fiber (N.A.=0.20). The maximum and mini-
mum of the allowed range of average transmitter power coupled into the fiber are worst case values to account for manufacturing
variances, drift due to temperature variations, and aging effects. The minimum launched optical power specified assumes an infi-
nite extinction ratio at the minimum specified OMA.
2. Optical transition time is the time interval required for the rising or falling edge of an optical pulse to transition between the 20% and
80% amplitudes relative to the logical 1 and 0 levels. This is measured through a 4th order Bessel -Thompson filter with 0.75 *
Data Rate 3-dB bandwidth and corrected to the full bandwidth value.
3. Optical Modulation Amplitude (OMA) is defined as the difference in optical power between a logic level one and a logic level zero.
The Optical Modulation Amplitude is defined in terms of average optical power (PAVG in mW) and extinction ratio (ER) as given by
OMA=2PAVG((ER-1)/(ER+1)). In this expression, the extinction ratio, the ratio of the average optical power (in mW) in a logic level
one to the average optical power in a logic level zero measured under fully modulated conditions in the presence of worst case
reflections, must be the absolute (unitless linear) ratio and not expressed in dB. The specified Optical Modulation Amplitude is
equivalent to an average power of -9 dBm at an extinction ratio of 9 dB.
4. RIN12 is the laser noise, integrated over a specified bandwidth, measured relative to average optical power with 12dB return loss.
See ANSI Fibre Channel Specification Annex A.
5. Eye opening is the portion of the bit time where the bit error rate (BER) £ 10-12. 1.0625Gb/s values meet the criteria listed in Ref
[1].
6. Deterministic Jitter is measured as the peak-to-peak timing variation of the 50% optical signal crossings when transmitting repeti-
tive K28.5 characters. It is defined in FC-PH, version 4.3, clause 3.1.87 as:
Timing distortions caused by normal circuit effects in the transmission system. Deterministic jitter is often subdivided into
duty cycle distortion (DCD) caused by propagation differences between the two transitions of a signal and data depen-
dent jitter (DDJ) caused by the interaction of the limited bandwidth of the transmission system components and the sym-
bol sequence. 1.0625Gb/s values meet the criteria listed in Ref [1].
7. Coupled Power Ratio is the ratio of the average power coupled into a multimode fiber to the average power coupled into a single
mode fiber. This measurement is defined in EIA/TIA-526-14A.
03/06/02
Page 11 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Optical Cable and Connector Specifications (Short Wavelength)
Symbol
Parameter
Min
Typical
Max.
Unit
Notes
50/125 mm Cable Specifications (Multimode 850 nm, 400 MHz-km)
L
L
Length - 2.125 Gb/s
2
2
260
450
m
m
Length - 1.0625 Gb/s
Bandwidth @ l = 850 nm
BW
400
MHz-km
m
3.5
dB/km
Attenuation @ l = 850 nm
c
N.A.
Numerical Aperture
0.20
50/125 mm Cable Specifications (Multimode 850 nm, 500 MHz-km)
L
L
Length - 2.125 Gb/s
2
2
300
500
m
m
Length - 1.0625 Gb/s
Bandwidth @ l = 850 nm
BW
500
MHz-km
m
3.5
dB/km
Attenuation @ l = 850 nm
c
N.A.
Numerical Aperture
0.20
62.5/125 mm Cable Specifications (Multimode 850 nm, 160 MHz-km)
L
L
Length - 2.125 Gb/s
2
2
120
250
m
m
Length - 1.0625 Gb/s
Bandwidth @ l = 850 nm
BW
160
MHz-km
m
3.75
dB/km
Attenuation @ l = 850 nm
c
N.A.
Numerical Aperture
0.275
62.5/125 mm Cable Specifications (Multimode 850 nm, 200 MHz-km)
L
L
Length - 2.125 Gb/s
2
2
150
300
m
m
Length - 1.0625 Gb/s
Bandwidth @ l = 850 nm
BW
200
MHz-km
m
3.75
dB/km
Attenuation @ l = 850 nm
c
N.A.
Numerical Aperture
0.275
LC Optical Connector Specifications (Multimode)
m
Nominal Attenuation
0.25
0.15
0.4
dB
dB
1
1
1
con
s con
Attenuation Standard Deviation
Connects/Disconnects
250
cycles
1. The optical interface connector dimensionally conforms to the industry standard LC type connector documented in [1]. A dual
keyed LC receptacle mechanically aligns the optical transmission fiber to the SFF-PTH-SW-2X5/2X6.
03/06/02
Page 12 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Reliability Projections
Symbol
Parameter
Max.
0.01
Unit
Note
1
AFR
Average Failure Rate
%/khr
1. AFR specified over 44 khours at 50°C, with minimum airflow of 100 fpm.
ESD Compliance
Symbol
ESDEP
ESDLC
Parameter
HBM ESD Rating to Electrical Pins
Air Discharge into Front Bezel
Compliance
+/- 2000
Unit
V
Notes
1
2
+/- 15000
V
1. The HBM (human body model) is a 100 pF capacitor discharged through a 1.5 kW resistor into each pin per JESD22-A114-B.
2. Complies with European ESD Immunity Test (C-B-2-0001-034).
Soldering Information
The SFF transceiver comes with a process/dust plug. When the plug is in place the transceiver can withstand
normal wave soldering and aqueous spray cleaning processes. While the transceiver is able to withstand an
aqueous cleaning process, it is not hermetically sealed; it was not designed to be immersed in cleaning sol-
vents. An opening in the back of the top lid is to allow compressed air to be blown into the module to aid in the
removal of trapped water. This process should be performed after aqueous cleaning with the plug still
inserted. If the plug was not contaminated during the wave soldering and aqueous spray cleaning process it
can be reused as a dust plug.
03/06/02
Page 13 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Mechanical Description (2 X 5 Pin 3 mm Configuration)
The SFF-PTH-SW-2X5/2X6 3 mm is intended to be used on a host card having a thickness of 0.062" to
0.100”. The host card footprint with essential keepouts and drill holes is shown in Host Card Footprint (2 X 5
Pin Configuration) on page 16.
03/06/02
Page 14 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Mechanical Description (2 X 5 Pin 4.5 mm Configuration)
The SFF-PTH-SW-2X5/2X6 4.5 mm is intended to be used on a host card having a thickness of 0.100" to
0.160”. The host card footprint with essential keepouts and drill holes is shown in Host Card Footprint (2 X 5
Pin Configuration) on page 16.
03/06/02
Page 15 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Host Card Footprint (2 X 5 Pin Configuration)
03/06/02
Page 16 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Mechanical Description (2 X 6 Pin 3 mm Configuration)
The SFF-PTH-SW-2X5/2X6 3 mm is intended to be used on a host card having a thickness of 0.062" to
0.100”. The host card footprint with essential keepouts and drill holes is shown in Host Card Footprint (2 X 6
Pin Configuration) on page 19.
03/06/02
Page 17 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Mechanical Description (2 X 6 Pin 4.5 mm Configuration)
The SFF-PTH-SW-2X5/2X6 4.5 mm is intended to be used on a host card having a thickness of 0.100" to
0.160”. The host card footprint with essential keepouts and drill holes is shown in Host Card Footprint (2 X 6
Pin Configuration) on page 19.
03/06/02
Page 18 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Host Card Footprint (2 X 6 Pin Configuration)
03/06/02
Page 19 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Suggested Transceiver/Host Interface
SFF
+3.3 V
1 uH
VccT
6
0.1uF
10 uF
0.1uF
10 uF
1 kohm
Tx_Disable
TD+
8
9
0.01uF
TX+
TX-
Transmitter
Driver
100 ohm
0.01uF
TD- 10
+3.3 V
100 ohm differential pair
10 kohm
ASIC
Fault detection logic
Tx_Fault
VeeT
B
1
+3.3 V
100 ohm differential pair
RX+
RX-
1 uH
VccR
2
10 uF
0.1 uF
10 uF
0.1 uF
0.01 uF
RX+
5
4
Receiver
Amplifier
100 ohm
0.01 uF
RX-
Rx_SD
3
VeeR
7
03/06/02
Page 20 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
References
Standards
1. American National Standards Institute Inc. (ANSI), T11/Project 1235-DT/Rev 10, Fibre Channel-Physical
Interface (FC-PI). Drafts of this standard are available to members of the standards working committee.
For further information see the T11.2 website at www.t11.org. To be added to the email reflector, send an
E-mail to:
majordomo@dpt.com
containing the line:
subscribe t11.2 <your email address>
2. American National Standards Institute Inc. (ANSI), T11.2/Project 1230/Rev10, Fibre Channel-Methodolo-
gies for Jitter Specifications (MJS). Drafts of this standard are available to members of the standards
working committee. For further information see the T11.2 website at www.t11.org. To be added to the
email reflector, send an E-mail to:
majordomo@network.com
containing the line:
subscribe T11 <your email address>
Industry Specifications
3. A.X. Widmer and P.A. Franaszek, “A DC-Balanced, Partitioned-Block, 8B/10B Transmission Code,” IBM
Journal of Research and Development, vol. 27, no. 5, pp. 440-451, September 1983. This paper fully
defines the 8B/10B code. It is primarily theoretical.
4. A.X. Widmer, The ANSI Fibre Channel Transmission Code, IBM Research Report, RC 18855 (82405),
April, 23 1993. Copies may be requested from:
Publications
IBM Thomas J. Watson Research Center
Post Office Box 218
Yorktown Heights, New York 10598
Phone: (914) 945-1259
Fax: (914) 945-4144
03/06/02
Page 21 of 22
JSF-21S0AA1
JSF-21S2AA1
JSG-21S1AA1
JSG-21S3AA1
SW 2x / 1x Fibre Channel Small Form Factor PTH Transceiver
Revision Log
Date
Description of Modification
08/15/00
Initial release.
Page 1, Added Dissipation words
Page 7, Added Dissipation words and rounded off numbers
Page 13, Changed Fall Time, Wavelength, Launched Power, and OMA to match industry specs.
Page 16, Rearranged ESD table
3/14/01
Page 21, New updated schematic
Page 17,19, New pictures with air access hole
New SW versions with longer EMI fingers
Voltage range increased to +/-10%
Page 2, new picture and laser safety wording
As of 1/1/2002, JDS Uniphase purchased the IBM optical transceiver group. The next revision of the specification
will be referenced with these part numbers:
02/08/02
03/06/02
JSF-21S0AA1 will be JSF-21S0AA1.
JSG-21S1AA1 will be JSG-21S1AA1.
JSG-21S3AA1 will be JSF-21L0AA1.
JSF-21S2AA1 will be JSG-211AA1.
JDS Uniphase Specification
New picture
03/06/02
Page 22 of 22
Ó JDS Uniphase Corporation 2002
Printed in the United States of America, April 2002
All statements, technical information and recommendations related to the products herein are based upon information
believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no respon-
sibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use
of a product or its application. JDS Uniphase reserves the right to change at any time without notice the design, speci-
fications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for
sale herein. JDS Uniphase makes no representations that the products herein are free from any intellectual property
claims of others. Please contact JDS Uniphase for more information. JDS Uniphase and the JDS Uniphase logo are
trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. Copyright
JDS Uniphase Corporation. All rights reserved.
The JDS Uniphase home page can be found at http://www.jdsu.com
1/2Gbps SFF PTH.07
03/06/02
相关型号:
JSFC1-12.000MHZ
Series - Fundamental Quartz Crystal, 12MHz Nom, ROHS COMPLIANT, CERAMIC PACKAGE-4
MMD
JSFC1-12.000MHZ-T
Series - Fundamental Quartz Crystal, 12MHz Nom, ROHS COMPLIANT, CERAMIC PACKAGE-4
MMD
JSFC1-16.000MHZ
Series - Fundamental Quartz Crystal, 16MHz Nom, ROHS COMPLIANT, CERAMIC PACKAGE-4
MMD
JSFC1-16.000MHZ-T
Series - Fundamental Quartz Crystal, 16MHz Nom, ROHS COMPLIANT, CERAMIC PACKAGE-4
MMD
JSFC1-8.000MHZ-T
Series - Fundamental Quartz Crystal, 8MHz Nom, ROHS COMPLIANT, CERAMIC PACKAGE-4
MMD
©2020 ICPDF网 联系我们和版权申明